Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 209 insertions, 0 deletions

diff --git a/arch/mips/netlogic/xlp/ahci-init.c b/arch/mips/netlogic/xlp/ahci-init.c
new file mode 100644
index 000000000..92be1a325
--- /dev/null
+++ b/arch/mips/netlogic/xlp/ahci-init.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright (c) 2003-2014 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <linux/bitops.h>
+
+#include <asm/cpu.h>
+#include <asm/mipsregs.h>
+
+#include <asm/netlogic/haldefs.h>
+#include <asm/netlogic/xlp-hal/xlp.h>
+#include <asm/netlogic/common.h>
+#include <asm/netlogic/xlp-hal/iomap.h>
+#include <asm/netlogic/mips-extns.h>
+
+#define SATA_CTL		0x0
+#define SATA_STATUS		0x1	/* Status Reg */
+#define SATA_INT		0x2	/* Interrupt Reg */
+#define SATA_INT_MASK		0x3	/* Interrupt Mask Reg */
+#define SATA_CR_REG_TIMER	0x4	/* PHY Conrol Timer Reg */
+#define SATA_CORE_ID		0x5	/* Core ID Reg */
+#define SATA_AXI_SLAVE_OPT1	0x6	/* AXI Slave Options Reg */
+#define SATA_PHY_LOS_LEV	0x7	/* PHY LOS Level Reg */
+#define SATA_PHY_MULTI		0x8	/* PHY Multiplier Reg */
+#define SATA_PHY_CLK_SEL	0x9	/* Clock Select Reg */
+#define SATA_PHY_AMP1_GEN1	0xa	/* PHY Transmit Amplitude Reg 1 */
+#define SATA_PHY_AMP1_GEN2	0xb	/* PHY Transmit Amplitude Reg 2 */
+#define SATA_PHY_AMP1_GEN3	0xc	/* PHY Transmit Amplitude Reg 3 */
+#define SATA_PHY_PRE1		0xd	/* PHY Transmit Preemphasis Reg 1 */
+#define SATA_PHY_PRE2		0xe	/* PHY Transmit Preemphasis Reg 2 */
+#define SATA_PHY_PRE3		0xf	/* PHY Transmit Preemphasis Reg 3 */
+#define SATA_SPDMODE		0x10	/* Speed Mode Reg */
+#define SATA_REFCLK		0x11	/* Reference Clock Control Reg */
+#define SATA_BYTE_SWAP_DIS	0x12	/* byte swap disable */
+
+/*SATA_CTL Bits */
+#define SATA_RST_N		BIT(0)
+#define PHY0_RESET_N		BIT(16)
+#define PHY1_RESET_N		BIT(17)
+#define PHY2_RESET_N		BIT(18)
+#define PHY3_RESET_N		BIT(19)
+#define M_CSYSREQ		BIT(2)
+#define S_CSYSREQ		BIT(3)
+
+/*SATA_STATUS Bits */
+#define P0_PHY_READY		BIT(4)
+#define P1_PHY_READY		BIT(5)
+#define P2_PHY_READY		BIT(6)
+#define P3_PHY_READY		BIT(7)
+
+#define nlm_read_sata_reg(b, r)		nlm_read_reg(b, r)
+#define nlm_write_sata_reg(b, r, v)	nlm_write_reg(b, r, v)
+#define nlm_get_sata_pcibase(node)	\
+		nlm_pcicfg_base(XLP_IO_SATA_OFFSET(node))
+/* SATA device specific configuration registers are starts at 0x900 offset */
+#define nlm_get_sata_regbase(node)	\
+		(nlm_get_sata_pcibase(node) + 0x900)
+
+static void sata_clear_glue_reg(uint64_t regbase, uint32_t off, uint32_t bit)
+{
+	uint32_t reg_val;
+
+	reg_val = nlm_read_sata_reg(regbase, off);
+	nlm_write_sata_reg(regbase, off, (reg_val & ~bit));
+}
+
+static void sata_set_glue_reg(uint64_t regbase, uint32_t off, uint32_t bit)
+{
+	uint32_t reg_val;
+
+	reg_val = nlm_read_sata_reg(regbase, off);
+	nlm_write_sata_reg(regbase, off, (reg_val | bit));
+}
+
+static void nlm_sata_firmware_init(int node)
+{
+	uint32_t reg_val;
+	uint64_t regbase;
+	int i;
+
+	pr_info("XLP AHCI Initialization started.\n");
+	regbase = nlm_get_sata_regbase(node);
+
+	/* Reset SATA */
+	sata_clear_glue_reg(regbase, SATA_CTL, SATA_RST_N);
+	/* Reset PHY */
+	sata_clear_glue_reg(regbase, SATA_CTL,
+			(PHY3_RESET_N | PHY2_RESET_N
+			 | PHY1_RESET_N | PHY0_RESET_N));
+
+	/* Set SATA */
+	sata_set_glue_reg(regbase, SATA_CTL, SATA_RST_N);
+	/* Set PHY */
+	sata_set_glue_reg(regbase, SATA_CTL,
+			(PHY3_RESET_N | PHY2_RESET_N
+			 | PHY1_RESET_N | PHY0_RESET_N));
+
+	pr_debug("Waiting for PHYs to come up.\n");
+	i = 0;
+	do {
+		reg_val = nlm_read_sata_reg(regbase, SATA_STATUS);
+		i++;
+	} while (((reg_val & 0xF0) != 0xF0) && (i < 10000));
+
+	for (i = 0; i < 4; i++) {
+		if (reg_val  & (P0_PHY_READY << i))
+			pr_info("PHY%d is up.\n", i);
+		else
+			pr_info("PHY%d is down.\n", i);
+	}
+
+	pr_info("XLP AHCI init done.\n");
+}
+
+static int __init nlm_ahci_init(void)
+{
+	int node = 0;
+	int chip = read_c0_prid() & PRID_IMP_MASK;
+
+	if (chip == PRID_IMP_NETLOGIC_XLP3XX)
+		nlm_sata_firmware_init(node);
+	return 0;
+}
+
+static void nlm_sata_intr_ack(struct irq_data *data)
+{
+	uint32_t val = 0;
+	uint64_t regbase;
+
+	regbase = nlm_get_sata_regbase(nlm_nodeid());
+	val = nlm_read_sata_reg(regbase, SATA_INT);
+	sata_set_glue_reg(regbase, SATA_INT, val);
+}
+
+static void nlm_sata_fixup_bar(struct pci_dev *dev)
+{
+	/*
+	 * The AHCI resource is in BAR 0, move it to
+	 * BAR 5, where it is expected
+	 */
+	dev->resource[5] = dev->resource[0];
+	memset(&dev->resource[0], 0, sizeof(dev->resource[0]));
+}
+
+static void nlm_sata_fixup_final(struct pci_dev *dev)
+{
+	uint32_t val;
+	uint64_t regbase;
+	int node = 0; /* XLP3XX does not support multi-node */
+
+	regbase = nlm_get_sata_regbase(node);
+
+	/* clear pending interrupts and then enable them */
+	val = nlm_read_sata_reg(regbase, SATA_INT);
+	sata_set_glue_reg(regbase, SATA_INT, val);
+
+	/* Mask the core interrupt. If all the interrupts
+	 * are enabled there are spurious interrupt flow
+	 * happening, to avoid only enable core interrupt
+	 * mask.
+	 */
+	sata_set_glue_reg(regbase, SATA_INT_MASK, 0x1);
+
+	dev->irq = PIC_SATA_IRQ;
+	nlm_set_pic_extra_ack(node, PIC_SATA_IRQ, nlm_sata_intr_ack);
+}
+
+arch_initcall(nlm_ahci_init);
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_SATA,
+		nlm_sata_fixup_bar);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_SATA,
+		nlm_sata_fixup_final);