Adding debian version 5.10.209-2.debian/5.10.209-2

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 423 insertions, 0 deletions

diff --git a/debian/patches/features/arm64/arm64-dts-raspberry-Add-support-for-the-CM4.patch b/debian/patches/features/arm64/arm64-dts-raspberry-Add-support-for-the-CM4.patch
new file mode 100644
index 000000000..8619cfcdd
--- /dev/null
+++ b/debian/patches/features/arm64/arm64-dts-raspberry-Add-support-for-the-CM4.patch
@@ -0,0 +1,423 @@
+From: Cyril Brulebois <cyril@debamax.com>
+Date: Mon, 03 Jan 2022 21:59:36 +0100
+Subject: arm64: dts: Add support for Raspberry Pi Compute Module 4 IO Board
+
+It was introduced in mainline during the v5.16 release cycle. Since
+many broadcom includes were reworked since v5.10, adding support would
+involve more than cherry-picking a DTS addition that uses a few
+includes.
+
+To avoid side effects on other models, introduce a DTS that leverages
+some existing includes (bcm2711.dtsi and bcm283x-rpi-usb-host.dtsi)
+and describes the rest without re-using parts of the Raspberry Pi 4 B
+model.
+
+To avoid phandle rotation (0x16, 0x17, and 0x18) across 3 nodes
+(dma@7e007000, i2c@7e205000, and interrupt-controller@7ef00100), and the
+related changes in other nodes referencing them, hardcode 0x16 as the
+phandle for interrupt-controller@7ef00100. This leads to an empty dtdiff
+between this new DTB and the one produced by a v5.16-rc8 build.
+
+Authored-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
+Reviewed-by: Cyril Brulebois <cyril@debamax.com>
+
+--- a/arch/arm64/boot/dts/broadcom/Makefile
++++ b/arch/arm64/boot/dts/broadcom/Makefile
+@@ -1,5 +1,6 @@
+ # SPDX-License-Identifier: GPL-2.0
+ dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-4-b.dtb \
++			      bcm2711-rpi-cm4-io.dtb \
+ 			      bcm2837-rpi-3-a-plus.dtb \
+ 			      bcm2837-rpi-3-b.dtb \
+ 			      bcm2837-rpi-3-b-plus.dtb \
+--- /dev/null
++++ b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
+@@ -0,0 +1,2 @@
++// SPDX-License-Identifier: GPL-2.0
++#include "arm/bcm2711-rpi-cm4-io.dts"
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
+ 	bcm2837-rpi-3-b-plus.dtb \
+ 	bcm2837-rpi-cm3-io3.dtb \
+ 	bcm2711-rpi-4-b.dtb \
++	bcm2711-rpi-cm4-io.dtb \
+ 	bcm2835-rpi-zero.dtb \
+ 	bcm2835-rpi-zero-w.dtb
+ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts
+@@ -0,0 +1,373 @@
++/dts-v1/;
++
++#include "bcm2711.dtsi"
++#include "bcm283x-rpi-usb-host.dtsi"
++
++/ {
++	model = "Raspberry Pi Compute Module 4 IO Board";
++	compatible = "raspberrypi,4-compute-module\0brcm,bcm2711";
++
++	aliases {
++		emmc2bus = "/emmc2bus";
++		ethernet0 = "/scb/ethernet@7d580000";
++		pcie0 = "/scb/pcie@7d500000";
++		blconfig = &blconfig;
++	};
++
++	chosen {
++		stdout-path = "serial1:115200n8";
++	};
++
++	leds {
++		compatible = "gpio-leds";
++
++		led-act {
++			label = "ACT";
++			default-state = "keep";
++			linux,default-trigger = "heartbeat";
++			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
++		};
++
++		led-pwr {
++			label = "PWR";
++			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
++			default-state = "keep";
++			linux,default-trigger = "default-on";
++		};
++	};
++
++	soc {
++		aon_intr: interrupt-controller@7ef00100 {
++			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
++			reg = <0x7ef00100 0x30>;
++			phandle = <0x16>;
++			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
++			interrupt-controller;
++			#interrupt-cells = <1>;
++		};
++
++		firmware: firmware {
++			compatible = "raspberrypi,bcm2835-firmware\0simple-mfd";
++			#address-cells = <0x01>;
++			#size-cells = <0x01>;
++			mboxes = <&mailbox>;
++			dma-ranges;
++
++			firmware_clocks: clocks {
++				compatible = "raspberrypi,firmware-clocks";
++				#clock-cells = <0x01>;
++			};
++
++			expgpio: gpio {
++				compatible = "raspberrypi,firmware-gpio";
++				gpio-controller;
++				#gpio-cells = <2>;
++				status = "okay";
++				gpio-line-names = "BT_ON", "WL_ON", "PWR_LED_OFF", "ANT1", "VDD_SD_IO_SEL", "CAM_GPIO", "SD_PWR_ON", "ANT2";
++				ant1-hog {
++					gpio-hog;
++					gpios = <0x03 0x00>;
++					output-high;
++					line-name = "ant1";
++				};
++
++				ant2-hog {
++					gpio-hog;
++					gpios = <0x07 0x00>;
++					output-low;
++					line-name = "ant2";
++				};
++			};
++
++			reset {
++				compatible = "raspberrypi,firmware-reset";
++				#reset-cells = <1>;
++			};
++		};
++
++		power: power {
++			compatible = "raspberrypi,bcm2835-power";
++			firmware = <&firmware>;
++			#power-domain-cells = <1>;
++		};
++
++		mailbox@7e00b840 {
++			compatible = "brcm,bcm2835-vchiq";
++			reg = <0x7e00b840 0x3c>;
++			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
++		};
++
++		vec@7ec13000 {
++			compatible = "brcm,bcm2711-vec";
++			reg = <0x7ec13000 0x1000>;
++			clocks = <&clocks BCM2835_CLOCK_VEC>;
++			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
++			status = "disabled";
++			power-domains = <&power /* RPI_POWER_DOMAIN_VEC = */ 7>;
++		};
++	};
++
++	memory@0 {
++		device_type = "memory";
++		reg = <0x00 0x00 0x00>;
++	};
++
++	wifi_pwrseq: wifi-pwrseq {
++		compatible = "mmc-pwrseq-simple";
++		reset-gpios = <&expgpio 0x01 0x01>;
++	};
++
++	sd_io_1v8_reg: sd_io_1v8_reg {
++		compatible = "regulator-gpio";
++		regulator-name = "vdd-sd-io";
++		regulator-min-microvolt = <1800000>;
++		regulator-max-microvolt = <3300000>;
++		regulator-boot-on;
++		regulator-always-on;
++		regulator-settling-time-us = <5000>;
++		gpios = <&expgpio 0x04 GPIO_ACTIVE_HIGH>;
++		states = <1800000 0x1>,
++			 <3300000 0x0>;
++		status = "okay";
++	};
++
++	sd_vcc_reg: sd_vcc_reg {
++		compatible = "regulator-fixed";
++		regulator-name = "vcc-sd";
++		regulator-min-microvolt = <3300000>;
++		regulator-max-microvolt = <3300000>;
++		regulator-boot-on;
++		enable-active-high;
++		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
++	};
++};
++
++&ddc0 {
++	status = "okay";
++};
++
++&ddc1 {
++	status = "okay";
++};
++
++&dsi0 {
++	power-domains = <&power 17>;
++};
++
++&dsi1 {
++	compatible = "brcm,bcm2711-dsi1";
++	power-domains = <&power 18>;
++};
++
++&emmc2 {
++	status = "okay";
++	bus-width = <8>;
++	vqmmc-supply = <&sd_io_1v8_reg>;
++	vmmc-supply = <&sd_vcc_reg>;
++	broken-cd;
++	mmc-hs200-1_8v;
++};
++
++&gpio {
++	pinctrl-names = "default";
++	/*
++	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
++	 * the official GPU firmware DT blob.
++	 *
++	 * Legend:
++	 * "FOO" = GPIO line named "FOO" on the schematic
++	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
++	 */
++	gpio-line-names = "ID_SDA",
++			  "ID_SCL",
++			  "SDA1",
++			  "SCL1",
++			  "GPIO_GCLK",
++			  "GPIO5",
++			  "GPIO6",
++			  "SPI_CE1_N",
++			  "SPI_CE0_N",
++			  "SPI_MISO",
++			  "SPI_MOSI",
++			  "SPI_SCLK",
++			  "GPIO12",
++			  "GPIO13",
++			  /* Serial port */
++			  "TXD1",
++			  "RXD1",
++			  "GPIO16",
++			  "GPIO17",
++			  "GPIO18",
++			  "GPIO19",
++			  "GPIO20",
++			  "GPIO21",
++			  "GPIO22",
++			  "GPIO23",
++			  "GPIO24",
++			  "GPIO25",
++			  "GPIO26",
++			  "GPIO27",
++			  "RGMII_MDIO",
++			  "RGMIO_MDC",
++			  /* Used by BT module */
++			  "CTS0",
++			  "RTS0",
++			  "TXD0",
++			  "RXD0",
++			  /* Used by Wifi */
++			  "SD1_CLK",
++			  "SD1_CMD",
++			  "SD1_DATA0",
++			  "SD1_DATA1",
++			  "SD1_DATA2",
++			  "SD1_DATA3",
++			  /* Shared with SPI flash */
++			  "PWM0_MISO",
++			  "PWM1_MOSI",
++			  "STATUS_LED_G_CLK",
++			  "SPIFLASH_CE_N",
++			  "SDA0",
++			  "SCL0",
++			  "RGMII_RXCLK",
++			  "RGMII_RXCTL",
++			  "RGMII_RXD0",
++			  "RGMII_RXD1",
++			  "RGMII_RXD2",
++			  "RGMII_RXD3",
++			  "RGMII_TXCLK",
++			  "RGMII_TXCTL",
++			  "RGMII_TXD0",
++			  "RGMII_TXD1",
++			  "RGMII_TXD2",
++			  "RGMII_TXD3";
++
++	gpioout {
++		brcm,pins = <0x06>;
++		brcm,function = <0x01>;
++	};
++
++	alt0 {
++		brcm,pins = <0x04 0x05 0x07 0x08 0x09 0x0a 0x0b>;
++		brcm,function = <0x04>;
++	};
++};
++
++&hdmi0 {
++	status = "okay";
++	interrupt-parent = <&aon_intr>;
++	interrupts = <0>, <1>, <2>, <3>, <4>, <5>;
++	interrupt-names = "cec-tx", "cec-rx", "cec-low", "wakeup", "hpd-connected", "hpd-removed";
++	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
++	wifi-2.4ghz-coexistence;
++};
++
++&hdmi1 {
++	status = "okay";
++	interrupt-parent = <&aon_intr>;
++	interrupts = <8>, <7>, <6>, <9>, <10>, <11>;
++	interrupt-names = "cec-tx", "cec-rx", "cec-low", "wakeup", "hpd-connected", "hpd-removed";
++	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
++	wifi-2.4ghz-coexistence;
++};
++
++&hvs {
++	clocks = <&firmware_clocks 4>;
++};
++
++&i2c0 {
++	status = "okay";
++	pinctrl-names = "default";
++	pinctrl-0 = <&i2c0_gpio0>;
++	clock-frequency = <100000>;
++};
++
++&i2c1 {
++	status = "okay";
++	pinctrl-names = "default";
++	pinctrl-0 = <&i2c1_gpio2>;
++	clock-frequency = <100000>;
++};
++
++&genet {
++	status = "okay";
++	phy-handle = <&ethphy0>;
++	phy-mode = "rgmii-rxid";
++};
++
++&genet_mdio {
++	ethphy0: ethernet-phy@0 {
++		reg = <0>;
++	};
++};
++
++&pixelvalve0 {
++	status = "okay";
++};
++
++&pixelvalve1 {
++	status = "okay";
++};
++
++&pixelvalve2 {
++	status = "okay";
++};
++
++&pixelvalve4 {
++	status = "okay";
++};
++
++&rmem {
++	blconfig: nvram@0 {
++		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
++		#address-cells = <0x01>;
++		#size-cells = <0x01>;
++		reg = <0x00 0x00 0x00>;
++		no-map;
++		status = "disabled";
++	};
++};
++
++&sdhci {
++	status = "okay";
++	#address-cells = <1>;
++	#size-cells = <0>;
++	pinctrl-names = "default";
++	pinctrl-0 = <&emmc_gpio34>;
++	bus-width = <4>;
++	non-removable;
++	mmc-pwrseq = <&wifi_pwrseq>;
++
++	wifi@1 {
++		reg = <0x01>;
++		compatible = "brcm,bcm4329-fmac";
++	};
++};
++
++&uart0 {
++	status = "okay";
++	pinctrl-names = "default";
++	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
++	uart-has-rtscts;
++
++	bluetooth {
++		compatible = "brcm,bcm43438-bt";
++		max-speed = <0x1e8480>;
++		shutdown-gpios = <&expgpio 0x00 0x00>;
++	};
++};
++
++&uart1 {
++	status = "okay";
++	pinctrl-names = "default";
++	pinctrl-0 = <&uart1_gpio14>;
++};
++
++&usb {
++	power-domains = <&power 6>;
++};
++
++&vc4 {
++	status = "okay";
++};
++
++/delete-node/ &vec;