Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1533 insertions, 0 deletions

diff --git a/drivers/gpu/drm/gma500/psb_intel_reg.h b/drivers/gpu/drm/gma500/psb_intel_reg.h
new file mode 100644
index 000000000..835cc924c
--- /dev/null
+++ b/drivers/gpu/drm/gma500/psb_intel_reg.h
@@ -0,0 +1,1533 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2009, Intel Corporation.
+ */
+#ifndef __PSB_INTEL_REG_H__
+#define __PSB_INTEL_REG_H__
+
+/*
+ * GPIO regs
+ */
+#define GPIOA			0x5010
+#define GPIOB			0x5014
+#define GPIOC			0x5018
+#define GPIOD			0x501c
+#define GPIOE			0x5020
+#define GPIOF			0x5024
+#define GPIOG			0x5028
+#define GPIOH			0x502c
+# define GPIO_CLOCK_DIR_MASK		(1 << 0)
+# define GPIO_CLOCK_DIR_IN		(0 << 1)
+# define GPIO_CLOCK_DIR_OUT		(1 << 1)
+# define GPIO_CLOCK_VAL_MASK		(1 << 2)
+# define GPIO_CLOCK_VAL_OUT		(1 << 3)
+# define GPIO_CLOCK_VAL_IN		(1 << 4)
+# define GPIO_CLOCK_PULLUP_DISABLE	(1 << 5)
+# define GPIO_DATA_DIR_MASK		(1 << 8)
+# define GPIO_DATA_DIR_IN		(0 << 9)
+# define GPIO_DATA_DIR_OUT		(1 << 9)
+# define GPIO_DATA_VAL_MASK		(1 << 10)
+# define GPIO_DATA_VAL_OUT		(1 << 11)
+# define GPIO_DATA_VAL_IN		(1 << 12)
+# define GPIO_DATA_PULLUP_DISABLE	(1 << 13)
+
+#define GMBUS0			0x5100 /* clock/port select */
+#define   GMBUS_RATE_100KHZ	(0<<8)
+#define   GMBUS_RATE_50KHZ	(1<<8)
+#define   GMBUS_RATE_400KHZ	(2<<8) /* reserved on Pineview */
+#define   GMBUS_RATE_1MHZ	(3<<8) /* reserved on Pineview */
+#define   GMBUS_HOLD_EXT	(1<<7) /* 300ns hold time, rsvd on Pineview */
+#define   GMBUS_PORT_DISABLED	0
+#define   GMBUS_PORT_SSC	1
+#define   GMBUS_PORT_VGADDC	2
+#define   GMBUS_PORT_PANEL	3
+#define   GMBUS_PORT_DPC	4 /* HDMIC */
+#define   GMBUS_PORT_DPB	5 /* SDVO, HDMIB */
+				  /* 6 reserved */
+#define   GMBUS_PORT_DPD	7 /* HDMID */
+#define   GMBUS_NUM_PORTS       8
+#define GMBUS1			0x5104 /* command/status */
+#define   GMBUS_SW_CLR_INT	(1<<31)
+#define   GMBUS_SW_RDY		(1<<30)
+#define   GMBUS_ENT		(1<<29) /* enable timeout */
+#define   GMBUS_CYCLE_NONE	(0<<25)
+#define   GMBUS_CYCLE_WAIT	(1<<25)
+#define   GMBUS_CYCLE_INDEX	(2<<25)
+#define   GMBUS_CYCLE_STOP	(4<<25)
+#define   GMBUS_BYTE_COUNT_SHIFT 16
+#define   GMBUS_SLAVE_INDEX_SHIFT 8
+#define   GMBUS_SLAVE_ADDR_SHIFT 1
+#define   GMBUS_SLAVE_READ	(1<<0)
+#define   GMBUS_SLAVE_WRITE	(0<<0)
+#define GMBUS2			0x5108 /* status */
+#define   GMBUS_INUSE		(1<<15)
+#define   GMBUS_HW_WAIT_PHASE	(1<<14)
+#define   GMBUS_STALL_TIMEOUT	(1<<13)
+#define   GMBUS_INT		(1<<12)
+#define   GMBUS_HW_RDY		(1<<11)
+#define   GMBUS_SATOER		(1<<10)
+#define   GMBUS_ACTIVE		(1<<9)
+#define GMBUS3			0x510c /* data buffer bytes 3-0 */
+#define GMBUS4			0x5110 /* interrupt mask (Pineview+) */
+#define   GMBUS_SLAVE_TIMEOUT_EN (1<<4)
+#define   GMBUS_NAK_EN		(1<<3)
+#define   GMBUS_IDLE_EN		(1<<2)
+#define   GMBUS_HW_WAIT_EN	(1<<1)
+#define   GMBUS_HW_RDY_EN	(1<<0)
+#define GMBUS5			0x5120 /* byte index */
+#define   GMBUS_2BYTE_INDEX_EN	(1<<31)
+
+#define BLC_PWM_CTL		0x61254
+#define BLC_PWM_CTL2		0x61250
+#define  PWM_ENABLE		(1 << 31)
+#define  PWM_LEGACY_MODE	(1 << 30)
+#define  PWM_PIPE_B		(1 << 29)
+#define BLC_PWM_CTL_C		0x62254
+#define BLC_PWM_CTL2_C		0x62250
+#define BACKLIGHT_MODULATION_FREQ_SHIFT		(17)
+/*
+ * This is the most significant 15 bits of the number of backlight cycles in a
+ * complete cycle of the modulated backlight control.
+ *
+ * The actual value is this field multiplied by two.
+ */
+#define BACKLIGHT_MODULATION_FREQ_MASK	(0x7fff << 17)
+#define BLM_LEGACY_MODE			(1 << 16)
+/*
+ * This is the number of cycles out of the backlight modulation cycle for which
+ * the backlight is on.
+ *
+ * This field must be no greater than the number of cycles in the complete
+ * backlight modulation cycle.
+ */
+#define BACKLIGHT_DUTY_CYCLE_SHIFT	(0)
+#define BACKLIGHT_DUTY_CYCLE_MASK	(0xffff)
+
+#define I915_GCFGC			0xf0
+#define I915_LOW_FREQUENCY_ENABLE	(1 << 7)
+#define I915_DISPLAY_CLOCK_190_200_MHZ	(0 << 4)
+#define I915_DISPLAY_CLOCK_333_MHZ	(4 << 4)
+#define I915_DISPLAY_CLOCK_MASK		(7 << 4)
+
+#define I855_HPLLCC			0xc0
+#define I855_CLOCK_CONTROL_MASK		(3 << 0)
+#define I855_CLOCK_133_200		(0 << 0)
+#define I855_CLOCK_100_200		(1 << 0)
+#define I855_CLOCK_100_133		(2 << 0)
+#define I855_CLOCK_166_250		(3 << 0)
+
+/* I830 CRTC registers */
+#define HTOTAL_A		0x60000
+#define HBLANK_A		0x60004
+#define HSYNC_A			0x60008
+#define VTOTAL_A		0x6000c
+#define VBLANK_A		0x60010
+#define VSYNC_A			0x60014
+#define PIPEASRC		0x6001c
+#define BCLRPAT_A		0x60020
+#define VSYNCSHIFT_A		0x60028
+
+#define HTOTAL_B		0x61000
+#define HBLANK_B		0x61004
+#define HSYNC_B			0x61008
+#define VTOTAL_B		0x6100c
+#define VBLANK_B		0x61010
+#define VSYNC_B			0x61014
+#define PIPEBSRC		0x6101c
+#define BCLRPAT_B		0x61020
+#define VSYNCSHIFT_B		0x61028
+
+#define HTOTAL_C		0x62000
+#define HBLANK_C		0x62004
+#define HSYNC_C			0x62008
+#define VTOTAL_C		0x6200c
+#define VBLANK_C		0x62010
+#define VSYNC_C			0x62014
+#define PIPECSRC		0x6201c
+#define BCLRPAT_C		0x62020
+#define VSYNCSHIFT_C		0x62028
+
+#define PP_STATUS		0x61200
+# define PP_ON				(1 << 31)
+/*
+ * Indicates that all dependencies of the panel are on:
+ *
+ * - PLL enabled
+ * - pipe enabled
+ * - LVDS/DVOB/DVOC on
+ */
+#define PP_READY			(1 << 30)
+#define PP_SEQUENCE_NONE		(0 << 28)
+#define PP_SEQUENCE_ON			(1 << 28)
+#define PP_SEQUENCE_OFF			(2 << 28)
+#define PP_SEQUENCE_MASK		0x30000000
+#define	PP_CYCLE_DELAY_ACTIVE		(1 << 27)
+#define	PP_SEQUENCE_STATE_ON_IDLE	(1 << 3)
+#define	PP_SEQUENCE_STATE_MASK		0x0000000f
+
+#define PP_CONTROL		0x61204
+#define POWER_TARGET_ON			(1 << 0)
+#define	PANEL_UNLOCK_REGS		(0xabcd << 16)
+#define	PANEL_UNLOCK_MASK		(0xffff << 16)
+#define	EDP_FORCE_VDD			(1 << 3)
+#define	EDP_BLC_ENABLE			(1 << 2)
+#define	PANEL_POWER_RESET		(1 << 1)
+#define	PANEL_POWER_OFF			(0 << 0)
+#define	PANEL_POWER_ON			(1 << 0)
+
+/* Poulsbo/Oaktrail */
+#define LVDSPP_ON		0x61208
+#define LVDSPP_OFF		0x6120c
+#define PP_CYCLE		0x61210
+
+/* Cedartrail */
+#define PP_ON_DELAYS		0x61208		/* Cedartrail */
+#define PANEL_PORT_SELECT_MASK 		(3 << 30)
+#define PANEL_PORT_SELECT_LVDS 		(0 << 30)
+#define PANEL_PORT_SELECT_EDP		(1 << 30)
+#define PANEL_POWER_UP_DELAY_MASK	(0x1fff0000)
+#define PANEL_POWER_UP_DELAY_SHIFT	16
+#define PANEL_LIGHT_ON_DELAY_MASK	(0x1fff)
+#define PANEL_LIGHT_ON_DELAY_SHIFT	0
+
+#define PP_OFF_DELAYS		0x6120c		/* Cedartrail */
+#define PANEL_POWER_DOWN_DELAY_MASK	(0x1fff0000)
+#define PANEL_POWER_DOWN_DELAY_SHIFT	16
+#define PANEL_LIGHT_OFF_DELAY_MASK	(0x1fff)
+#define PANEL_LIGHT_OFF_DELAY_SHIFT	0
+
+#define PP_DIVISOR		0x61210		/* Cedartrail */
+#define  PP_REFERENCE_DIVIDER_MASK	(0xffffff00)
+#define  PP_REFERENCE_DIVIDER_SHIFT	8
+#define  PANEL_POWER_CYCLE_DELAY_MASK	(0x1f)
+#define  PANEL_POWER_CYCLE_DELAY_SHIFT	0
+
+#define PFIT_CONTROL		0x61230
+#define PFIT_ENABLE			(1 << 31)
+#define PFIT_PIPE_MASK			(3 << 29)
+#define PFIT_PIPE_SHIFT			29
+#define PFIT_SCALING_MODE_PILLARBOX	(1 << 27)
+#define PFIT_SCALING_MODE_LETTERBOX	(3 << 26)
+#define VERT_INTERP_DISABLE		(0 << 10)
+#define VERT_INTERP_BILINEAR		(1 << 10)
+#define VERT_INTERP_MASK		(3 << 10)
+#define VERT_AUTO_SCALE			(1 << 9)
+#define HORIZ_INTERP_DISABLE		(0 << 6)
+#define HORIZ_INTERP_BILINEAR		(1 << 6)
+#define HORIZ_INTERP_MASK		(3 << 6)
+#define HORIZ_AUTO_SCALE		(1 << 5)
+#define PANEL_8TO6_DITHER_ENABLE	(1 << 3)
+
+#define PFIT_PGM_RATIOS		0x61234
+#define PFIT_VERT_SCALE_MASK			0xfff00000
+#define PFIT_HORIZ_SCALE_MASK			0x0000fff0
+
+#define PFIT_AUTO_RATIOS	0x61238
+
+#define DPLL_A			0x06014
+#define DPLL_B			0x06018
+#define DPLL_VCO_ENABLE			(1 << 31)
+#define DPLL_DVO_HIGH_SPEED		(1 << 30)
+#define DPLL_SYNCLOCK_ENABLE		(1 << 29)
+#define DPLL_VGA_MODE_DIS		(1 << 28)
+#define DPLLB_MODE_DAC_SERIAL		(1 << 26)	/* i915 */
+#define DPLLB_MODE_LVDS			(2 << 26)	/* i915 */
+#define DPLL_MODE_MASK			(3 << 26)
+#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10	(0 << 24)	/* i915 */
+#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5	(1 << 24)	/* i915 */
+#define DPLLB_LVDS_P2_CLOCK_DIV_14	(0 << 24)	/* i915 */
+#define DPLLB_LVDS_P2_CLOCK_DIV_7	(1 << 24)	/* i915 */
+#define DPLL_P2_CLOCK_DIV_MASK		0x03000000	/* i915 */
+#define DPLL_FPA0h1_P1_POST_DIV_MASK	0x00ff0000	/* i915 */
+#define DPLL_LOCK			(1 << 15)	/* CDV */
+
+/*
+ *  The i830 generation, in DAC/serial mode, defines p1 as two plus this
+ * bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set.
+ */
+# define DPLL_FPA01_P1_POST_DIV_MASK_I830	0x001f0000
+/*
+ * The i830 generation, in LVDS mode, defines P1 as the bit number set within
+ * this field (only one bit may be set).
+ */
+#define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS	0x003f0000
+#define DPLL_FPA01_P1_POST_DIV_SHIFT	16
+#define PLL_P2_DIVIDE_BY_4		(1 << 23)	/* i830, required
+							 * in DVO non-gang */
+# define PLL_P1_DIVIDE_BY_TWO		(1 << 21)	/* i830 */
+#define PLL_REF_INPUT_DREFCLK		(0 << 13)
+#define PLL_REF_INPUT_TVCLKINA		(1 << 13)	/* i830 */
+#define PLL_REF_INPUT_TVCLKINBC		(2 << 13)	/* SDVO
+								 * TVCLKIN */
+#define PLLB_REF_INPUT_SPREADSPECTRUMIN	(3 << 13)
+#define PLL_REF_INPUT_MASK		(3 << 13)
+#define PLL_LOAD_PULSE_PHASE_SHIFT	9
+/*
+ * Parallel to Serial Load Pulse phase selection.
+ * Selects the phase for the 10X DPLL clock for the PCIe
+ * digital display port. The range is 4 to 13; 10 or more
+ * is just a flip delay. The default is 6
+ */
+#define PLL_LOAD_PULSE_PHASE_MASK	(0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
+#define DISPLAY_RATE_SELECT_FPA1	(1 << 8)
+
+/*
+ * SDVO multiplier for 945G/GM. Not used on 965.
+ *
+ * DPLL_MD_UDI_MULTIPLIER_MASK
+ */
+#define SDVO_MULTIPLIER_MASK		0x000000ff
+#define SDVO_MULTIPLIER_SHIFT_HIRES	4
+#define SDVO_MULTIPLIER_SHIFT_VGA	0
+
+/*
+ * PLL_MD
+ */
+/* Pipe A SDVO/UDI clock multiplier/divider register for G965. */
+#define DPLL_A_MD		0x0601c
+/* Pipe B SDVO/UDI clock multiplier/divider register for G965. */
+#define DPLL_B_MD		0x06020
+/*
+ * UDI pixel divider, controlling how many pixels are stuffed into a packet.
+ *
+ * Value is pixels minus 1.  Must be set to 1 pixel for SDVO.
+ */
+#define DPLL_MD_UDI_DIVIDER_MASK	0x3f000000
+#define DPLL_MD_UDI_DIVIDER_SHIFT	24
+/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
+#define DPLL_MD_VGA_UDI_DIVIDER_MASK	0x003f0000
+#define DPLL_MD_VGA_UDI_DIVIDER_SHIFT	16
+/*
+ * SDVO/UDI pixel multiplier.
+ *
+ * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus
+ * clock rate is 10 times the DPLL clock.  At low resolution/refresh rate
+ * modes, the bus rate would be below the limits, so SDVO allows for stuffing
+ * dummy bytes in the datastream at an increased clock rate, with both sides of
+ * the link knowing how many bytes are fill.
+ *
+ * So, for a mode with a dotclock of 65Mhz, we would want to double the clock
+ * rate to 130Mhz to get a bus rate of 1.30Ghz.  The DPLL clock rate would be
+ * set to 130Mhz, and the SDVO multiplier set to 2x in this register and
+ * through an SDVO command.
+ *
+ * This register field has values of multiplication factor minus 1, with
+ * a maximum multiplier of 5 for SDVO.
+ */
+#define DPLL_MD_UDI_MULTIPLIER_MASK	0x00003f00
+#define DPLL_MD_UDI_MULTIPLIER_SHIFT	8
+/*
+ * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
+ * This best be set to the default value (3) or the CRT won't work. No,
+ * I don't entirely understand what this does...
+ */
+#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK	0x0000003f
+#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
+
+#define DPLL_TEST		0x606c
+#define DPLLB_TEST_SDVO_DIV_1		(0 << 22)
+#define DPLLB_TEST_SDVO_DIV_2		(1 << 22)
+#define DPLLB_TEST_SDVO_DIV_4		(2 << 22)
+#define DPLLB_TEST_SDVO_DIV_MASK	(3 << 22)
+#define DPLLB_TEST_N_BYPASS		(1 << 19)
+#define DPLLB_TEST_M_BYPASS		(1 << 18)
+#define DPLLB_INPUT_BUFFER_ENABLE	(1 << 16)
+#define DPLLA_TEST_N_BYPASS		(1 << 3)
+#define DPLLA_TEST_M_BYPASS		(1 << 2)
+#define DPLLA_INPUT_BUFFER_ENABLE	(1 << 0)
+
+#define ADPA			0x61100
+#define ADPA_DAC_ENABLE			(1 << 31)
+#define ADPA_DAC_DISABLE		0
+#define ADPA_PIPE_SELECT_MASK		(1 << 30)
+#define ADPA_PIPE_A_SELECT		0
+#define ADPA_PIPE_B_SELECT		(1 << 30)
+#define ADPA_USE_VGA_HVPOLARITY		(1 << 15)
+#define ADPA_SETS_HVPOLARITY		0
+#define ADPA_VSYNC_CNTL_DISABLE		(1 << 11)
+#define ADPA_VSYNC_CNTL_ENABLE		0
+#define ADPA_HSYNC_CNTL_DISABLE		(1 << 10)
+#define ADPA_HSYNC_CNTL_ENABLE		0
+#define ADPA_VSYNC_ACTIVE_HIGH		(1 << 4)
+#define ADPA_VSYNC_ACTIVE_LOW		0
+#define ADPA_HSYNC_ACTIVE_HIGH		(1 << 3)
+#define ADPA_HSYNC_ACTIVE_LOW		0
+
+#define FPA0			0x06040
+#define FPA1			0x06044
+#define FPB0			0x06048
+#define FPB1			0x0604c
+#define FP_N_DIV_MASK			0x003f0000
+#define FP_N_DIV_SHIFT			16
+#define FP_M1_DIV_MASK			0x00003f00
+#define FP_M1_DIV_SHIFT			8
+#define FP_M2_DIV_MASK			0x0000003f
+#define FP_M2_DIV_SHIFT			0
+
+#define PORT_HOTPLUG_EN		0x61110
+#define HDMIB_HOTPLUG_INT_EN		(1 << 29)
+#define HDMIC_HOTPLUG_INT_EN		(1 << 28)
+#define HDMID_HOTPLUG_INT_EN		(1 << 27)
+#define SDVOB_HOTPLUG_INT_EN		(1 << 26)
+#define SDVOC_HOTPLUG_INT_EN		(1 << 25)
+#define TV_HOTPLUG_INT_EN		(1 << 18)
+#define CRT_HOTPLUG_INT_EN		(1 << 9)
+#define CRT_HOTPLUG_FORCE_DETECT	(1 << 3)
+/* CDV.. */
+#define CRT_HOTPLUG_ACTIVATION_PERIOD_64	(1 << 8)
+#define CRT_HOTPLUG_DAC_ON_TIME_2M		(0 << 7)
+#define CRT_HOTPLUG_DAC_ON_TIME_4M		(1 << 7)
+#define CRT_HOTPLUG_VOLTAGE_COMPARE_40		(0 << 5)
+#define CRT_HOTPLUG_VOLTAGE_COMPARE_50		(1 << 5)
+#define CRT_HOTPLUG_VOLTAGE_COMPARE_60		(2 << 5)
+#define CRT_HOTPLUG_VOLTAGE_COMPARE_70		(3 << 5)
+#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK	(3 << 5)
+#define CRT_HOTPLUG_DETECT_DELAY_1G		(0 << 4)
+#define CRT_HOTPLUG_DETECT_DELAY_2G		(1 << 4)
+#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV	(0 << 2)
+#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV	(1 << 2)
+#define CRT_HOTPLUG_DETECT_MASK			0x000000F8
+
+#define PORT_HOTPLUG_STAT	0x61114
+#define CRT_HOTPLUG_INT_STATUS		(1 << 11)
+#define TV_HOTPLUG_INT_STATUS		(1 << 10)
+#define CRT_HOTPLUG_MONITOR_MASK	(3 << 8)
+#define CRT_HOTPLUG_MONITOR_COLOR	(3 << 8)
+#define CRT_HOTPLUG_MONITOR_MONO	(2 << 8)
+#define CRT_HOTPLUG_MONITOR_NONE	(0 << 8)
+#define SDVOC_HOTPLUG_INT_STATUS	(1 << 7)
+#define SDVOB_HOTPLUG_INT_STATUS	(1 << 6)
+
+#define SDVOB			0x61140
+#define SDVOC			0x61160
+#define SDVO_ENABLE			(1 << 31)
+#define SDVO_PIPE_B_SELECT		(1 << 30)
+#define SDVO_STALL_SELECT		(1 << 29)
+#define SDVO_INTERRUPT_ENABLE		(1 << 26)
+#define SDVO_COLOR_RANGE_16_235		(1 << 8)
+#define SDVO_AUDIO_ENABLE		(1 << 6)
+
+/**
+ * 915G/GM SDVO pixel multiplier.
+ *
+ * Programmed value is multiplier - 1, up to 5x.
+ *
+ * DPLL_MD_UDI_MULTIPLIER_MASK
+ */
+#define SDVO_PORT_MULTIPLY_MASK		(7 << 23)
+#define SDVO_PORT_MULTIPLY_SHIFT	23
+#define SDVO_PHASE_SELECT_MASK		(15 << 19)
+#define SDVO_PHASE_SELECT_DEFAULT	(6 << 19)
+#define SDVO_CLOCK_OUTPUT_INVERT	(1 << 18)
+#define SDVOC_GANG_MODE			(1 << 16)
+#define SDVO_BORDER_ENABLE		(1 << 7)
+#define SDVOB_PCIE_CONCURRENCY		(1 << 3)
+#define SDVO_DETECTED			(1 << 2)
+/* Bits to be preserved when writing */
+#define SDVOB_PRESERVE_MASK		((1 << 17) | (1 << 16) | (1 << 14))
+#define SDVOC_PRESERVE_MASK		(1 << 17)
+
+/*
+ * This register controls the LVDS output enable, pipe selection, and data
+ * format selection.
+ *
+ * All of the clock/data pairs are force powered down by power sequencing.
+ */
+#define LVDS			0x61180
+/*
+ * Enables the LVDS port.  This bit must be set before DPLLs are enabled, as
+ * the DPLL semantics change when the LVDS is assigned to that pipe.
+ */
+#define LVDS_PORT_EN			(1 << 31)
+/* Selects pipe B for LVDS data.  Must be set on pre-965. */
+#define LVDS_PIPEB_SELECT		(1 << 30)
+
+/* Turns on border drawing to allow centered display. */
+#define LVDS_BORDER_EN			(1 << 15)
+
+/*
+ * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
+ * pixel.
+ */
+#define LVDS_A0A2_CLKA_POWER_MASK	(3 << 8)
+#define LVDS_A0A2_CLKA_POWER_DOWN	(0 << 8)
+#define LVDS_A0A2_CLKA_POWER_UP		(3 << 8)
+/*
+ * Controls the A3 data pair, which contains the additional LSBs for 24 bit
+ * mode.  Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
+ * on.
+ */
+#define LVDS_A3_POWER_MASK		(3 << 6)
+#define LVDS_A3_POWER_DOWN		(0 << 6)
+#define LVDS_A3_POWER_UP		(3 << 6)
+/*
+ * Controls the CLKB pair.  This should only be set when LVDS_B0B3_POWER_UP
+ * is set.
+ */
+#define LVDS_CLKB_POWER_MASK		(3 << 4)
+#define LVDS_CLKB_POWER_DOWN		(0 << 4)
+#define LVDS_CLKB_POWER_UP		(3 << 4)
+/*
+ * Controls the B0-B3 data pairs.  This must be set to match the DPLL p2
+ * setting for whether we are in dual-channel mode.  The B3 pair will
+ * additionally only be powered up when LVDS_A3_POWER_UP is set.
+ */
+#define LVDS_B0B3_POWER_MASK		(3 << 2)
+#define LVDS_B0B3_POWER_DOWN		(0 << 2)
+#define LVDS_B0B3_POWER_UP		(3 << 2)
+
+#define PIPEACONF		0x70008
+#define PIPEACONF_ENABLE		(1 << 31)
+#define PIPEACONF_DISABLE		0
+#define PIPEACONF_DOUBLE_WIDE		(1 << 30)
+#define PIPECONF_ACTIVE			(1 << 30)
+#define PIPECONF_DSIPLL_LOCK		(1 << 29)
+#define PIPEACONF_SINGLE_WIDE		0
+#define PIPEACONF_PIPE_UNLOCKED		0
+#define PIPEACONF_DSR			(1 << 26)
+#define PIPEACONF_PIPE_LOCKED		(1 << 25)
+#define PIPEACONF_PALETTE		0
+#define PIPECONF_FORCE_BORDER		(1 << 25)
+#define PIPEACONF_GAMMA			(1 << 24)
+#define PIPECONF_PROGRESSIVE		(0 << 21)
+#define PIPECONF_INTERLACE_W_FIELD_INDICATION	(6 << 21)
+#define PIPECONF_INTERLACE_FIELD_0_ONLY		(7 << 21)
+#define PIPECONF_PLANE_OFF		(1 << 19)
+#define PIPECONF_CURSOR_OFF		(1 << 18)
+
+#define PIPEBCONF		0x71008
+#define PIPEBCONF_ENABLE		(1 << 31)
+#define PIPEBCONF_DISABLE		0
+#define PIPEBCONF_DOUBLE_WIDE		(1 << 30)
+#define PIPEBCONF_DISABLE		0
+#define PIPEBCONF_GAMMA			(1 << 24)
+#define PIPEBCONF_PALETTE		0
+
+#define PIPECCONF		0x72008
+
+#define PIPEBGCMAXRED		0x71010
+#define PIPEBGCMAXGREEN		0x71014
+#define PIPEBGCMAXBLUE		0x71018
+
+#define PIPEASTAT		0x70024
+#define PIPEBSTAT		0x71024
+#define PIPECSTAT		0x72024
+#define PIPE_VBLANK_INTERRUPT_STATUS		(1UL << 1)
+#define PIPE_START_VBLANK_INTERRUPT_STATUS	(1UL << 2)
+#define PIPE_VBLANK_CLEAR			(1 << 1)
+#define PIPE_VBLANK_STATUS			(1 << 1)
+#define PIPE_TE_STATUS				(1UL << 6)
+#define PIPE_DPST_EVENT_STATUS			(1UL << 7)
+#define PIPE_VSYNC_CLEAR			(1UL << 9)
+#define PIPE_VSYNC_STATUS			(1UL << 9)
+#define PIPE_HDMI_AUDIO_UNDERRUN_STATUS		(1UL << 10)
+#define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS	(1UL << 11)
+#define PIPE_VBLANK_INTERRUPT_ENABLE		(1UL << 17)
+#define PIPE_START_VBLANK_INTERRUPT_ENABLE	(1UL << 18)
+#define PIPE_TE_ENABLE				(1UL << 22)
+#define PIPE_LEGACY_BLC_EVENT_ENABLE		(1UL << 22)
+#define PIPE_DPST_EVENT_ENABLE			(1UL << 23)
+#define PIPE_VSYNC_ENABL			(1UL << 25)
+#define PIPE_HDMI_AUDIO_UNDERRUN		(1UL << 26)
+#define PIPE_HDMI_AUDIO_BUFFER_DONE		(1UL << 27)
+#define PIPE_FIFO_UNDERRUN			(1UL << 31)
+#define PIPE_HDMI_AUDIO_INT_MASK		(PIPE_HDMI_AUDIO_UNDERRUN | \
+						PIPE_HDMI_AUDIO_BUFFER_DONE)
+#define PIPE_EVENT_MASK ((1 << 29)|(1 << 28)|(1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)|(1 << 22)|(1 << 21)|(1 << 20)|(1 << 16))
+#define PIPE_VBLANK_MASK ((1 << 25)|(1 << 24)|(1 << 18)|(1 << 17))
+#define HISTOGRAM_INT_CONTROL		0x61268
+#define HISTOGRAM_BIN_DATA		0X61264
+#define HISTOGRAM_LOGIC_CONTROL		0x61260
+#define PWM_CONTROL_LOGIC		0x61250
+#define PIPE_HOTPLUG_INTERRUPT_STATUS		(1UL << 10)
+#define HISTOGRAM_INTERRUPT_ENABLE		(1UL << 31)
+#define HISTOGRAM_LOGIC_ENABLE			(1UL << 31)
+#define PWM_LOGIC_ENABLE			(1UL << 31)
+#define PWM_PHASEIN_ENABLE			(1UL << 25)
+#define PWM_PHASEIN_INT_ENABLE			(1UL << 24)
+#define PWM_PHASEIN_VB_COUNT			0x00001f00
+#define PWM_PHASEIN_INC				0x0000001f
+#define HISTOGRAM_INT_CTRL_CLEAR		(1UL << 30)
+#define DPST_YUV_LUMA_MODE			0
+
+struct dpst_ie_histogram_control {
+	union {
+		uint32_t data;
+		struct {
+			uint32_t bin_reg_index:7;
+			uint32_t reserved:4;
+			uint32_t bin_reg_func_select:1;
+			uint32_t sync_to_phase_in:1;
+			uint32_t alt_enhancement_mode:2;
+			uint32_t reserved1:1;
+			uint32_t sync_to_phase_in_count:8;
+			uint32_t histogram_mode_select:1;
+			uint32_t reserved2:4;
+			uint32_t ie_pipe_assignment:1;
+			uint32_t ie_mode_table_enabled:1;
+			uint32_t ie_histogram_enable:1;
+		};
+	};
+};
+
+struct dpst_guardband {
+	union {
+		uint32_t data;
+		struct {
+			uint32_t guardband:22;
+			uint32_t guardband_interrupt_delay:8;
+			uint32_t interrupt_status:1;
+			uint32_t interrupt_enable:1;
+		};
+	};
+};
+
+#define PIPEAFRAMEHIGH		0x70040
+#define PIPEAFRAMEPIXEL		0x70044
+#define PIPEBFRAMEHIGH		0x71040
+#define PIPEBFRAMEPIXEL		0x71044
+#define PIPECFRAMEHIGH		0x72040
+#define PIPECFRAMEPIXEL		0x72044
+#define PIPE_FRAME_HIGH_MASK	0x0000ffff
+#define PIPE_FRAME_HIGH_SHIFT	0
+#define PIPE_FRAME_LOW_MASK	0xff000000
+#define PIPE_FRAME_LOW_SHIFT	24
+#define PIPE_PIXEL_MASK		0x00ffffff
+#define PIPE_PIXEL_SHIFT	0
+
+#define FW_BLC_SELF		0x20e0 
+#define FW_BLC_SELF_EN          (1<<15)
+
+#define DSPARB			0x70030
+#define DSPFW1			0x70034
+#define DSP_FIFO_SR_WM_MASK		0xFF800000
+#define DSP_FIFO_SR_WM_SHIFT		23
+#define CURSOR_B_FIFO_WM_MASK		0x003F0000
+#define CURSOR_B_FIFO_WM_SHIFT		16
+#define DSPFW2			0x70038
+#define CURSOR_A_FIFO_WM_MASK		0x3F00
+#define CURSOR_A_FIFO_WM_SHIFT		8
+#define DSP_PLANE_C_FIFO_WM_MASK	0x7F
+#define DSP_PLANE_C_FIFO_WM_SHIFT	0
+#define DSPFW3			0x7003c
+#define DSPFW4			0x70050
+#define DSPFW5			0x70054
+#define DSP_PLANE_B_FIFO_WM1_SHIFT	24
+#define DSP_PLANE_A_FIFO_WM1_SHIFT	16
+#define CURSOR_B_FIFO_WM1_SHIFT		8
+#define CURSOR_FIFO_SR_WM1_SHIFT	0
+#define DSPFW6			0x70058
+#define DSPCHICKENBIT		0x70400
+#define DSPACNTR		0x70180
+#define DSPBCNTR		0x71180
+#define DSPCCNTR		0x72180
+#define DISPLAY_PLANE_ENABLE			(1 << 31)
+#define DISPLAY_PLANE_DISABLE			0
+#define DISPPLANE_GAMMA_ENABLE			(1 << 30)
+#define DISPPLANE_GAMMA_DISABLE			0
+#define DISPPLANE_PIXFORMAT_MASK		(0xf << 26)
+#define DISPPLANE_8BPP				(0x2 << 26)
+#define DISPPLANE_15_16BPP			(0x4 << 26)
+#define DISPPLANE_16BPP				(0x5 << 26)
+#define DISPPLANE_32BPP_NO_ALPHA		(0x6 << 26)
+#define DISPPLANE_32BPP				(0x7 << 26)
+#define DISPPLANE_STEREO_ENABLE			(1 << 25)
+#define DISPPLANE_STEREO_DISABLE		0
+#define DISPPLANE_SEL_PIPE_MASK			(1 << 24)
+#define DISPPLANE_SEL_PIPE_POS			24
+#define DISPPLANE_SEL_PIPE_A			0
+#define DISPPLANE_SEL_PIPE_B			(1 << 24)
+#define DISPPLANE_SRC_KEY_ENABLE		(1 << 22)
+#define DISPPLANE_SRC_KEY_DISABLE		0
+#define DISPPLANE_LINE_DOUBLE			(1 << 20)
+#define DISPPLANE_NO_LINE_DOUBLE		0
+#define DISPPLANE_STEREO_POLARITY_FIRST		0
+#define DISPPLANE_STEREO_POLARITY_SECOND	(1 << 18)
+/* plane B only */
+#define DISPPLANE_ALPHA_TRANS_ENABLE		(1 << 15)
+#define DISPPLANE_ALPHA_TRANS_DISABLE		0
+#define DISPPLANE_SPRITE_ABOVE_DISPLAYA		0
+#define DISPPLANE_SPRITE_ABOVE_OVERLAY		(1)
+#define DISPPLANE_BOTTOM			(4)
+
+#define DSPABASE		0x70184
+#define DSPALINOFF		0x70184
+#define DSPASTRIDE		0x70188
+
+#define DSPBBASE		0x71184
+#define DSPBLINOFF		0X71184
+#define DSPBADDR		DSPBBASE
+#define DSPBSTRIDE		0x71188
+
+#define DSPCBASE		0x72184
+#define DSPCLINOFF		0x72184
+#define DSPCSTRIDE		0x72188
+
+#define DSPAKEYVAL		0x70194
+#define DSPAKEYMASK		0x70198
+
+#define DSPAPOS			0x7018C	/* reserved */
+#define DSPASIZE		0x70190
+#define DSPBPOS			0x7118C
+#define DSPBSIZE		0x71190
+#define DSPCPOS			0x7218C
+#define DSPCSIZE		0x72190
+
+#define DSPASURF		0x7019C
+#define DSPATILEOFF		0x701A4
+
+#define DSPBSURF		0x7119C
+#define DSPBTILEOFF		0x711A4
+
+#define DSPCSURF		0x7219C
+#define DSPCTILEOFF		0x721A4
+#define DSPCKEYMAXVAL		0x721A0
+#define DSPCKEYMINVAL		0x72194
+#define DSPCKEYMSK		0x72198
+
+#define VGACNTRL		0x71400
+#define VGA_DISP_DISABLE		(1 << 31)
+#define VGA_2X_MODE			(1 << 30)
+#define VGA_PIPE_B_SELECT		(1 << 29)
+
+/*
+ * Overlay registers
+ */
+#define OV_C_OFFSET		0x08000
+#define OV_OVADD		0x30000
+#define OV_DOVASTA		0x30008
+# define OV_PIPE_SELECT			((1 << 6)|(1 << 7))
+# define OV_PIPE_SELECT_POS		6
+# define OV_PIPE_A			0
+# define OV_PIPE_C			1
+#define OV_OGAMC5		0x30010
+#define OV_OGAMC4		0x30014
+#define OV_OGAMC3		0x30018
+#define OV_OGAMC2		0x3001C
+#define OV_OGAMC1		0x30020
+#define OV_OGAMC0		0x30024
+#define OVC_OVADD		0x38000
+#define OVC_DOVCSTA		0x38008
+#define OVC_OGAMC5		0x38010
+#define OVC_OGAMC4		0x38014
+#define OVC_OGAMC3		0x38018
+#define OVC_OGAMC2		0x3801C
+#define OVC_OGAMC1		0x38020
+#define OVC_OGAMC0		0x38024
+
+/*
+ * Some BIOS scratch area registers.  The 845 (and 830?) store the amount
+ * of video memory available to the BIOS in SWF1.
+ */
+#define SWF0			0x71410
+#define SWF1			0x71414
+#define SWF2			0x71418
+#define SWF3			0x7141c
+#define SWF4			0x71420
+#define SWF5			0x71424
+#define SWF6			0x71428
+
+/*
+ * 855 scratch registers.
+ */
+#define SWF00			0x70410
+#define SWF01			0x70414
+#define SWF02			0x70418
+#define SWF03			0x7041c
+#define SWF04			0x70420
+#define SWF05			0x70424
+#define SWF06			0x70428
+
+#define SWF10			SWF0
+#define SWF11			SWF1
+#define SWF12			SWF2
+#define SWF13			SWF3
+#define SWF14			SWF4
+#define SWF15			SWF5
+#define SWF16			SWF6
+
+#define SWF30			0x72414
+#define SWF31			0x72418
+#define SWF32			0x7241c
+
+
+/*
+ * Palette registers
+ */
+#define PALETTE_A		0x0a000
+#define PALETTE_B		0x0a800
+#define PALETTE_C		0x0ac00
+
+/* Cursor A & B regs */
+#define CURACNTR		0x70080
+#define CURSOR_MODE_DISABLE		0x00
+#define CURSOR_MODE_64_32B_AX		0x07
+#define CURSOR_MODE_64_ARGB_AX		((1 << 5) | CURSOR_MODE_64_32B_AX)
+#define MCURSOR_GAMMA_ENABLE		(1 << 26)
+#define CURABASE		0x70084
+#define CURAPOS			0x70088
+#define CURSOR_POS_MASK			0x007FF
+#define CURSOR_POS_SIGN			0x8000
+#define CURSOR_X_SHIFT			0
+#define CURSOR_Y_SHIFT			16
+#define CURBCNTR		0x700c0
+#define CURBBASE		0x700c4
+#define CURBPOS			0x700c8
+#define CURCCNTR		0x700e0
+#define CURCBASE		0x700e4
+#define CURCPOS			0x700e8
+
+/*
+ * Interrupt Registers
+ */
+#define IER			0x020a0
+#define IIR			0x020a4
+#define IMR			0x020a8
+#define ISR			0x020ac
+
+/*
+ * MOORESTOWN delta registers
+ */
+#define MRST_DPLL_A		0x0f014
+#define MDFLD_DPLL_B		0x0f018
+#define MDFLD_INPUT_REF_SEL		(1 << 14)
+#define MDFLD_VCO_SEL			(1 << 16)
+#define DPLLA_MODE_LVDS			(2 << 26)	/* mrst */
+#define MDFLD_PLL_LATCHEN		(1 << 28)
+#define MDFLD_PWR_GATE_EN		(1 << 30)
+#define MDFLD_P1_MASK			(0x1FF << 17)
+#define MRST_FPA0		0x0f040
+#define MRST_FPA1		0x0f044
+#define MDFLD_DPLL_DIV0		0x0f048
+#define MDFLD_DPLL_DIV1		0x0f04c
+#define MRST_PERF_MODE		0x020f4
+
+/*
+ * MEDFIELD HDMI registers
+ */
+#define HDMIPHYMISCCTL		0x61134
+#define HDMI_PHY_POWER_DOWN		0x7f
+#define HDMIB_CONTROL		0x61140
+#define HDMIB_PORT_EN			(1 << 31)
+#define HDMIB_PIPE_B_SELECT		(1 << 30)
+#define HDMIB_NULL_PACKET		(1 << 9)
+#define HDMIB_HDCP_PORT			(1 << 5)
+
+/* #define LVDS			0x61180 */
+#define MRST_PANEL_8TO6_DITHER_ENABLE	(1 << 25)
+#define MRST_PANEL_24_DOT_1_FORMAT	(1 << 24)
+#define LVDS_A3_POWER_UP_0_OUTPUT	(1 << 6)
+
+#define MIPI			0x61190
+#define MIPI_C			0x62190
+#define MIPI_PORT_EN			(1 << 31)
+/* Turns on border drawing to allow centered display. */
+#define SEL_FLOPPED_HSTX		(1 << 23)
+#define PASS_FROM_SPHY_TO_AFE		(1 << 16)
+#define MIPI_BORDER_EN			(1 << 15)
+#define MIPIA_3LANE_MIPIC_1LANE		0x1
+#define MIPIA_2LANE_MIPIC_2LANE		0x2
+#define TE_TRIGGER_DSI_PROTOCOL		(1 << 2)
+#define TE_TRIGGER_GPIO_PIN		(1 << 3)
+#define MIPI_TE_COUNT		0x61194
+
+/* #define PP_CONTROL	0x61204 */
+#define POWER_DOWN_ON_RESET		(1 << 1)
+
+/* #define PFIT_CONTROL	0x61230 */
+#define PFIT_PIPE_SELECT		(3 << 29)
+#define PFIT_PIPE_SELECT_SHIFT		(29)
+
+/* #define BLC_PWM_CTL		0x61254 */
+#define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT	(16)
+#define MRST_BACKLIGHT_MODULATION_FREQ_MASK	(0xffff << 16)
+
+/* #define PIPEACONF 0x70008 */
+#define PIPEACONF_PIPE_STATE		(1 << 30)
+/* #define DSPACNTR		0x70180 */
+
+#define MRST_DSPABASE		0x7019c
+#define MRST_DSPBBASE		0x7119c
+#define MDFLD_DSPCBASE		0x7219c
+
+/*
+ * Moorestown registers.
+ */
+
+/*
+ *	MIPI IP registers
+ */
+#define MIPIC_REG_OFFSET		0x800
+
+#define DEVICE_READY_REG		0xb000
+#define LP_OUTPUT_HOLD				(1 << 16)
+#define EXIT_ULPS_DEV_READY			0x3
+#define LP_OUTPUT_HOLD_RELEASE			0x810000
+# define ENTERING_ULPS				(2 << 1)
+# define EXITING_ULPS				(1 << 1)
+# define ULPS_MASK				(3 << 1)
+# define BUS_POSSESSION				(1 << 3)
+#define INTR_STAT_REG			0xb004
+#define RX_SOT_ERROR				(1 << 0)
+#define RX_SOT_SYNC_ERROR			(1 << 1)
+#define RX_ESCAPE_MODE_ENTRY_ERROR		(1 << 3)
+#define RX_LP_TX_SYNC_ERROR			(1 << 4)
+#define RX_HS_RECEIVE_TIMEOUT_ERROR		(1 << 5)
+#define RX_FALSE_CONTROL_ERROR			(1 << 6)
+#define RX_ECC_SINGLE_BIT_ERROR			(1 << 7)
+#define RX_ECC_MULTI_BIT_ERROR			(1 << 8)
+#define RX_CHECKSUM_ERROR			(1 << 9)
+#define RX_DSI_DATA_TYPE_NOT_RECOGNIZED		(1 << 10)
+#define RX_DSI_VC_ID_INVALID			(1 << 11)
+#define TX_FALSE_CONTROL_ERROR			(1 << 12)
+#define TX_ECC_SINGLE_BIT_ERROR			(1 << 13)
+#define TX_ECC_MULTI_BIT_ERROR			(1 << 14)
+#define TX_CHECKSUM_ERROR			(1 << 15)
+#define TX_DSI_DATA_TYPE_NOT_RECOGNIZED		(1 << 16)
+#define TX_DSI_VC_ID_INVALID			(1 << 17)
+#define HIGH_CONTENTION				(1 << 18)
+#define LOW_CONTENTION				(1 << 19)
+#define DPI_FIFO_UNDER_RUN			(1 << 20)
+#define HS_TX_TIMEOUT				(1 << 21)
+#define LP_RX_TIMEOUT				(1 << 22)
+#define TURN_AROUND_ACK_TIMEOUT			(1 << 23)
+#define ACK_WITH_NO_ERROR			(1 << 24)
+#define HS_GENERIC_WR_FIFO_FULL			(1 << 27)
+#define LP_GENERIC_WR_FIFO_FULL			(1 << 28)
+#define SPL_PKT_SENT				(1 << 30)
+#define INTR_EN_REG			0xb008
+#define DSI_FUNC_PRG_REG		0xb00c
+#define DPI_CHANNEL_NUMBER_POS			0x03
+#define DBI_CHANNEL_NUMBER_POS			0x05
+#define FMT_DPI_POS				0x07
+#define FMT_DBI_POS				0x0A
+#define DBI_DATA_WIDTH_POS			0x0D
+
+/* DPI PIXEL FORMATS */
+#define RGB_565_FMT				0x01	/* RGB 565 FORMAT */
+#define RGB_666_FMT				0x02	/* RGB 666 FORMAT */
+#define LRGB_666_FMT				0x03	/* RGB LOOSELY PACKED
+							 * 666 FORMAT
+							 */
+#define RGB_888_FMT				0x04	/* RGB 888 FORMAT */
+#define VIRTUAL_CHANNEL_NUMBER_0		0x00	/* Virtual channel 0 */
+#define VIRTUAL_CHANNEL_NUMBER_1		0x01	/* Virtual channel 1 */
+#define VIRTUAL_CHANNEL_NUMBER_2		0x02	/* Virtual channel 2 */
+#define VIRTUAL_CHANNEL_NUMBER_3		0x03	/* Virtual channel 3 */
+
+#define DBI_NOT_SUPPORTED			0x00	/* command mode
+							 * is not supported
+							 */
+#define DBI_DATA_WIDTH_16BIT			0x01	/* 16 bit data */
+#define DBI_DATA_WIDTH_9BIT			0x02	/* 9 bit data */
+#define DBI_DATA_WIDTH_8BIT			0x03	/* 8 bit data */
+#define DBI_DATA_WIDTH_OPT1			0x04	/* option 1 */
+#define DBI_DATA_WIDTH_OPT2			0x05	/* option 2 */
+
+#define HS_TX_TIMEOUT_REG		0xb010
+#define LP_RX_TIMEOUT_REG		0xb014
+#define TURN_AROUND_TIMEOUT_REG		0xb018
+#define DEVICE_RESET_REG		0xb01C
+#define DPI_RESOLUTION_REG		0xb020
+#define RES_V_POS				0x10
+#define DBI_RESOLUTION_REG		0xb024 /* Reserved for MDFLD */
+#define HORIZ_SYNC_PAD_COUNT_REG	0xb028
+#define HORIZ_BACK_PORCH_COUNT_REG	0xb02C
+#define HORIZ_FRONT_PORCH_COUNT_REG	0xb030
+#define HORIZ_ACTIVE_AREA_COUNT_REG	0xb034
+#define VERT_SYNC_PAD_COUNT_REG		0xb038
+#define VERT_BACK_PORCH_COUNT_REG	0xb03c
+#define VERT_FRONT_PORCH_COUNT_REG	0xb040
+#define HIGH_LOW_SWITCH_COUNT_REG	0xb044
+#define DPI_CONTROL_REG			0xb048
+#define DPI_SHUT_DOWN				(1 << 0)
+#define DPI_TURN_ON				(1 << 1)
+#define DPI_COLOR_MODE_ON			(1 << 2)
+#define DPI_COLOR_MODE_OFF			(1 << 3)
+#define DPI_BACK_LIGHT_ON			(1 << 4)
+#define DPI_BACK_LIGHT_OFF			(1 << 5)
+#define DPI_LP					(1 << 6)
+#define DPI_DATA_REG			0xb04c
+#define DPI_BACK_LIGHT_ON_DATA			0x07
+#define DPI_BACK_LIGHT_OFF_DATA			0x17
+#define INIT_COUNT_REG			0xb050
+#define MAX_RET_PAK_REG			0xb054
+#define VIDEO_FMT_REG			0xb058
+#define COMPLETE_LAST_PCKT			(1 << 2)
+#define EOT_DISABLE_REG			0xb05c
+#define ENABLE_CLOCK_STOPPING			(1 << 1)
+#define LP_BYTECLK_REG			0xb060
+#define LP_GEN_DATA_REG			0xb064
+#define HS_GEN_DATA_REG			0xb068
+#define LP_GEN_CTRL_REG			0xb06C
+#define HS_GEN_CTRL_REG			0xb070
+#define DCS_CHANNEL_NUMBER_POS		0x6
+#define MCS_COMMANDS_POS		0x8
+#define WORD_COUNTS_POS			0x8
+#define MCS_PARAMETER_POS			0x10
+#define GEN_FIFO_STAT_REG		0xb074
+#define HS_DATA_FIFO_FULL			(1 << 0)
+#define HS_DATA_FIFO_HALF_EMPTY			(1 << 1)
+#define HS_DATA_FIFO_EMPTY			(1 << 2)
+#define LP_DATA_FIFO_FULL			(1 << 8)
+#define LP_DATA_FIFO_HALF_EMPTY			(1 << 9)
+#define LP_DATA_FIFO_EMPTY			(1 << 10)
+#define HS_CTRL_FIFO_FULL			(1 << 16)
+#define HS_CTRL_FIFO_HALF_EMPTY			(1 << 17)
+#define HS_CTRL_FIFO_EMPTY			(1 << 18)
+#define LP_CTRL_FIFO_FULL			(1 << 24)
+#define LP_CTRL_FIFO_HALF_EMPTY			(1 << 25)
+#define LP_CTRL_FIFO_EMPTY			(1 << 26)
+#define DBI_FIFO_EMPTY				(1 << 27)
+#define DPI_FIFO_EMPTY				(1 << 28)
+#define HS_LS_DBI_ENABLE_REG		0xb078
+#define TXCLKESC_REG			0xb07c
+#define DPHY_PARAM_REG			0xb080
+#define DBI_BW_CTRL_REG			0xb084
+#define CLK_LANE_SWT_REG		0xb088
+
+/*
+ * MIPI Adapter registers
+ */
+#define MIPI_CONTROL_REG		0xb104
+#define MIPI_2X_CLOCK_BITS			((1 << 0) | (1 << 1))
+#define MIPI_DATA_ADDRESS_REG		0xb108
+#define MIPI_DATA_LENGTH_REG		0xb10C
+#define MIPI_COMMAND_ADDRESS_REG	0xb110
+#define MIPI_COMMAND_LENGTH_REG		0xb114
+#define MIPI_READ_DATA_RETURN_REG0	0xb118
+#define MIPI_READ_DATA_RETURN_REG1	0xb11C
+#define MIPI_READ_DATA_RETURN_REG2	0xb120
+#define MIPI_READ_DATA_RETURN_REG3	0xb124
+#define MIPI_READ_DATA_RETURN_REG4	0xb128
+#define MIPI_READ_DATA_RETURN_REG5	0xb12C
+#define MIPI_READ_DATA_RETURN_REG6	0xb130
+#define MIPI_READ_DATA_RETURN_REG7	0xb134
+#define MIPI_READ_DATA_VALID_REG	0xb138
+
+/* DBI COMMANDS */
+#define soft_reset			0x01
+/*
+ *	The display module performs a software reset.
+ *	Registers are written with their SW Reset default values.
+ */
+#define get_power_mode			0x0a
+/*
+ *	The display module returns the current power mode
+ */
+#define get_address_mode		0x0b
+/*
+ *	The display module returns the current status.
+ */
+#define get_pixel_format		0x0c
+/*
+ *	This command gets the pixel format for the RGB image data
+ *	used by the interface.
+ */
+#define get_display_mode		0x0d
+/*
+ *	The display module returns the Display Image Mode status.
+ */
+#define get_signal_mode			0x0e
+/*
+ *	The display module returns the Display Signal Mode.
+ */
+#define get_diagnostic_result		0x0f
+/*
+ *	The display module returns the self-diagnostic results following
+ *	a Sleep Out command.
+ */
+#define enter_sleep_mode		0x10
+/*
+ *	This command causes the display module to enter the Sleep mode.
+ *	In this mode, all unnecessary blocks inside the display module are
+ *	disabled except interface communication. This is the lowest power
+ *	mode the display module supports.
+ */
+#define exit_sleep_mode			0x11
+/*
+ *	This command causes the display module to exit Sleep mode.
+ *	All blocks inside the display module are enabled.
+ */
+#define enter_partial_mode		0x12
+/*
+ *	This command causes the display module to enter the Partial Display
+ *	Mode. The Partial Display Mode window is described by the
+ *	set_partial_area command.
+ */
+#define enter_normal_mode		0x13
+/*
+ *	This command causes the display module to enter the Normal mode.
+ *	Normal Mode is defined as Partial Display mode and Scroll mode are off
+ */
+#define exit_invert_mode		0x20
+/*
+ *	This command causes the display module to stop inverting the image
+ *	data on the display device. The frame memory contents remain unchanged.
+ *	No status bits are changed.
+ */
+#define enter_invert_mode		0x21
+/*
+ *	This command causes the display module to invert the image data only on
+ *	the display device. The frame memory contents remain unchanged.
+ *	No status bits are changed.
+ */
+#define set_gamma_curve			0x26
+/*
+ *	This command selects the desired gamma curve for the display device.
+ *	Four fixed gamma curves are defined in section DCS spec.
+ */
+#define set_display_off			0x28
+/* ************************************************************************* *\
+This command causes the display module to stop displaying the image data
+on the display device. The frame memory contents remain unchanged.
+No status bits are changed.
+\* ************************************************************************* */
+#define set_display_on			0x29
+/* ************************************************************************* *\
+This command causes the display module to start displaying the image data
+on the display device. The frame memory contents remain unchanged.
+No status bits are changed.
+\* ************************************************************************* */
+#define set_column_address		0x2a
+/*
+ *	This command defines the column extent of the frame memory accessed by
+ *	the hostprocessor with the read_memory_continue and
+ *	write_memory_continue commands.
+ *	No status bits are changed.
+ */
+#define set_page_addr			0x2b
+/*
+ *	This command defines the page extent of the frame memory accessed by
+ *	the host processor with the write_memory_continue and
+ *	read_memory_continue command.
+ *	No status bits are changed.
+ */
+#define write_mem_start			0x2c
+/*
+ *	This command transfers image data from the host processor to the
+ *	display modules frame memory starting at the pixel location specified
+ *	by preceding set_column_address and set_page_address commands.
+ */
+#define set_partial_area		0x30
+/*
+ *	This command defines the Partial Display mode s display area.
+ *	There are two parameters associated with this command, the first
+ *	defines the Start Row (SR) and the second the End Row (ER). SR and ER
+ *	refer to the Frame Memory Line Pointer.
+ */
+#define set_scroll_area			0x33
+/*
+ *	This command defines the display modules Vertical Scrolling Area.
+ */
+#define set_tear_off			0x34
+/*
+ *	This command turns off the display modules Tearing Effect output
+ *	signal on the TE signal line.
+ */
+#define set_tear_on			0x35
+/*
+ *	This command turns on the display modules Tearing Effect output signal
+ *	on the TE signal line.
+ */
+#define set_address_mode		0x36
+/*
+ *	This command sets the data order for transfers from the host processor
+ *	to display modules frame memory,bits B[7:5] and B3, and from the
+ *	display modules frame memory to the display device, bits B[2:0] and B4.
+ */
+#define set_scroll_start		0x37
+/*
+ *	This command sets the start of the vertical scrolling area in the frame
+ *	memory. The vertical scrolling area is fully defined when this command
+ *	is used with the set_scroll_area command The set_scroll_start command
+ *	has one parameter, the Vertical Scroll Pointer. The VSP defines the
+ *	line in the frame memory that is written to the display device as the
+ *	first line of the vertical scroll area.
+ */
+#define exit_idle_mode			0x38
+/*
+ *	This command causes the display module to exit Idle mode.
+ */
+#define enter_idle_mode			0x39
+/*
+ *	This command causes the display module to enter Idle Mode.
+ *	In Idle Mode, color expression is reduced. Colors are shown on the
+ *	display device using the MSB of each of the R, G and B color
+ *	components in the frame memory
+ */
+#define set_pixel_format		0x3a
+/*
+ *	This command sets the pixel format for the RGB image data used by the
+ *	interface.
+ *	Bits D[6:4]  DPI Pixel Format Definition
+ *	Bits D[2:0]  DBI Pixel Format Definition
+ *	Bits D7 and D3 are not used.
+ */
+#define DCS_PIXEL_FORMAT_3bpp		0x1
+#define DCS_PIXEL_FORMAT_8bpp		0x2
+#define DCS_PIXEL_FORMAT_12bpp		0x3
+#define DCS_PIXEL_FORMAT_16bpp		0x5
+#define DCS_PIXEL_FORMAT_18bpp		0x6
+#define DCS_PIXEL_FORMAT_24bpp		0x7
+
+#define write_mem_cont			0x3c
+
+/*
+ *	This command transfers image data from the host processor to the
+ *	display module's frame memory continuing from the pixel location
+ *	following the previous write_memory_continue or write_memory_start
+ *	command.
+ */
+#define set_tear_scanline		0x44
+/*
+ *	This command turns on the display modules Tearing Effect output signal
+ *	on the TE signal line when the display module reaches line N.
+ */
+#define get_scanline			0x45
+/*
+ *	The display module returns the current scanline, N, used to update the
+ *	 display device. The total number of scanlines on a display device is
+ *	defined as VSYNC + VBP + VACT + VFP.The first scanline is defined as
+ *	the first line of V Sync and is denoted as Line 0.
+ *	When in Sleep Mode, the value returned by get_scanline is undefined.
+ */
+
+/* MCS or Generic COMMANDS */
+/* MCS/generic data type */
+#define GEN_SHORT_WRITE_0	0x03  /* generic short write, no parameters */
+#define GEN_SHORT_WRITE_1	0x13  /* generic short write, 1 parameters */
+#define GEN_SHORT_WRITE_2	0x23  /* generic short write, 2 parameters */
+#define GEN_READ_0		0x04  /* generic read, no parameters */
+#define GEN_READ_1		0x14  /* generic read, 1 parameters */
+#define GEN_READ_2		0x24  /* generic read, 2 parameters */
+#define GEN_LONG_WRITE		0x29  /* generic long write */
+#define MCS_SHORT_WRITE_0	0x05  /* MCS short write, no parameters */
+#define MCS_SHORT_WRITE_1	0x15  /* MCS short write, 1 parameters */
+#define MCS_READ		0x06  /* MCS read, no parameters */
+#define MCS_LONG_WRITE		0x39  /* MCS long write */
+/* MCS/generic commands */
+/* TPO MCS */
+#define write_display_profile		0x50
+#define write_display_brightness	0x51
+#define write_ctrl_display		0x53
+#define write_ctrl_cabc			0x55
+  #define UI_IMAGE		0x01
+  #define STILL_IMAGE		0x02
+  #define MOVING_IMAGE		0x03
+#define write_hysteresis		0x57
+#define write_gamma_setting		0x58
+#define write_cabc_min_bright		0x5e
+#define write_kbbc_profile		0x60
+/* TMD MCS */
+#define tmd_write_display_brightness 0x8c
+
+/*
+ *	This command is used to control ambient light, panel backlight
+ *	brightness and gamma settings.
+ */
+#define BRIGHT_CNTL_BLOCK_ON	(1 << 5)
+#define AMBIENT_LIGHT_SENSE_ON	(1 << 4)
+#define DISPLAY_DIMMING_ON	(1 << 3)
+#define BACKLIGHT_ON		(1 << 2)
+#define DISPLAY_BRIGHTNESS_AUTO	(1 << 1)
+#define GAMMA_AUTO		(1 << 0)
+
+/* DCS Interface Pixel Formats */
+#define DCS_PIXEL_FORMAT_3BPP	0x1
+#define DCS_PIXEL_FORMAT_8BPP	0x2
+#define DCS_PIXEL_FORMAT_12BPP	0x3
+#define DCS_PIXEL_FORMAT_16BPP	0x5
+#define DCS_PIXEL_FORMAT_18BPP	0x6
+#define DCS_PIXEL_FORMAT_24BPP	0x7
+/* ONE PARAMETER READ DATA */
+#define addr_mode_data		0xfc
+#define diag_res_data		0x00
+#define disp_mode_data		0x23
+#define pxl_fmt_data		0x77
+#define pwr_mode_data		0x74
+#define sig_mode_data		0x00
+/* TWO PARAMETERS READ DATA */
+#define scanline_data1		0xff
+#define scanline_data2		0xff
+#define NON_BURST_MODE_SYNC_PULSE	0x01	/* Non Burst Mode
+						 * with Sync Pulse
+						 */
+#define NON_BURST_MODE_SYNC_EVENTS	0x02	/* Non Burst Mode
+						 * with Sync events
+						 */
+#define BURST_MODE			0x03	/* Burst Mode */
+#define DBI_COMMAND_BUFFER_SIZE		0x240   /* 0x32 */    /* 0x120 */
+						/* Allocate at least
+						 * 0x100 Byte with 32
+						 * byte alignment
+						 */
+#define DBI_DATA_BUFFER_SIZE		0x120	/* Allocate at least
+						 * 0x100 Byte with 32
+						 * byte alignment
+						 */
+#define DBI_CB_TIME_OUT			0xFFFF
+
+#define GEN_FB_TIME_OUT			2000
+
+#define SKU_83				0x01
+#define SKU_100				0x02
+#define SKU_100L			0x04
+#define SKU_BYPASS			0x08
+
+/* Some handy macros for playing with bitfields. */
+#define PSB_MASK(high, low) (((1<<((high)-(low)+1))-1)<<(low))
+#define SET_FIELD(value, field) (((value) << field ## _SHIFT) & field ## _MASK)
+#define GET_FIELD(word, field) (((word)  & field ## _MASK) >> field ## _SHIFT)
+
+#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
+
+/* PCI config space */
+
+#define SB_PCKT         0x02100 /* cedarview */
+# define SB_OPCODE_MASK                         PSB_MASK(31, 16)
+# define SB_OPCODE_SHIFT                        16
+# define SB_OPCODE_READ                         0
+# define SB_OPCODE_WRITE                        1
+# define SB_DEST_MASK                           PSB_MASK(15, 8)
+# define SB_DEST_SHIFT                          8
+# define SB_DEST_DPLL                           0x88
+# define SB_BYTE_ENABLE_MASK                    PSB_MASK(7, 4)
+# define SB_BYTE_ENABLE_SHIFT                   4
+# define SB_BUSY                                (1 << 0)
+
+#define DSPCLK_GATE_D		0x6200
+# define VRHUNIT_CLOCK_GATE_DISABLE		(1 << 28) /* Fixed value on CDV */
+# define DPOUNIT_CLOCK_GATE_DISABLE		(1 << 11)
+# define DPIOUNIT_CLOCK_GATE_DISABLE		(1 << 6)
+# define DPUNIT_PIPEB_GATE_DISABLE		(1 << 30)
+# define DPUNIT_PIPEA_GATE_DISABLE		(1 << 25)
+# define DPCUNIT_CLOCK_GATE_DISABLE		(1 << 24)
+# define DPLSUNIT_CLOCK_GATE_DISABLE		(1 << 13)
+
+#define RAMCLK_GATE_D		0x6210
+
+/* 32-bit value read/written from the DPIO reg. */
+#define SB_DATA		0x02104 /* cedarview */
+/* 32-bit address of the DPIO reg to be read/written. */
+#define SB_ADDR		0x02108 /* cedarview */
+#define DPIO_CFG	0x02110 /* cedarview */
+# define DPIO_MODE_SELECT_1			(1 << 3)
+# define DPIO_MODE_SELECT_0			(1 << 2)
+# define DPIO_SFR_BYPASS			(1 << 1)
+/* reset is active low */
+# define DPIO_CMN_RESET_N			(1 << 0)
+
+/* Cedarview sideband registers */
+#define _SB_M_A			0x8008
+#define _SB_M_B			0x8028
+#define SB_M(pipe) _PIPE(pipe, _SB_M_A, _SB_M_B)
+# define SB_M_DIVIDER_MASK			(0xFF << 24)
+# define SB_M_DIVIDER_SHIFT			24
+
+#define _SB_N_VCO_A		0x8014
+#define _SB_N_VCO_B		0x8034
+#define SB_N_VCO(pipe) _PIPE(pipe, _SB_N_VCO_A, _SB_N_VCO_B)
+#define SB_N_VCO_SEL_MASK			PSB_MASK(31, 30)
+#define SB_N_VCO_SEL_SHIFT			30
+#define SB_N_DIVIDER_MASK			PSB_MASK(29, 26)
+#define SB_N_DIVIDER_SHIFT			26
+#define SB_N_CB_TUNE_MASK			PSB_MASK(25, 24)
+#define SB_N_CB_TUNE_SHIFT			24
+
+/* the bit 14:13 is used to select between the different reference clock for Pipe A/B */
+#define SB_REF_DPLLA		0x8010
+#define SB_REF_DPLLB		0x8030
+#define	REF_CLK_MASK		(0x3 << 13)
+#define REF_CLK_CORE		(0 << 13)
+#define REF_CLK_DPLL		(1 << 13)
+#define REF_CLK_DPLLA		(2 << 13)
+/* For the DPLL B, it will use the reference clk from DPLL A when using (2 << 13) */
+
+#define _SB_REF_A		0x8018
+#define _SB_REF_B		0x8038
+#define SB_REF_SFR(pipe)	_PIPE(pipe, _SB_REF_A, _SB_REF_B)
+
+#define _SB_P_A			0x801c
+#define _SB_P_B			0x803c
+#define SB_P(pipe) _PIPE(pipe, _SB_P_A, _SB_P_B)
+#define SB_P2_DIVIDER_MASK			PSB_MASK(31, 30)
+#define SB_P2_DIVIDER_SHIFT			30
+#define SB_P2_10				0 /* HDMI, DP, DAC */
+#define SB_P2_5				1 /* DAC */
+#define SB_P2_14				2 /* LVDS single */
+#define SB_P2_7				3 /* LVDS double */
+#define SB_P1_DIVIDER_MASK			PSB_MASK(15, 12)
+#define SB_P1_DIVIDER_SHIFT			12
+
+#define PSB_LANE0		0x120
+#define PSB_LANE1		0x220
+#define PSB_LANE2		0x2320
+#define PSB_LANE3		0x2420
+
+#define LANE_PLL_MASK		(0x7 << 20)
+#define LANE_PLL_ENABLE		(0x3 << 20)
+#define LANE_PLL_PIPE(p)	(((p) == 0) ? (1 << 21) : (0 << 21))
+
+#define DP_B				0x64100
+#define DP_C				0x64200
+
+#define   DP_PORT_EN			(1 << 31)
+#define   DP_PIPEB_SELECT		(1 << 30)
+#define   DP_PIPE_MASK			(1 << 30)
+
+/* Link training mode - select a suitable mode for each stage */
+#define   DP_LINK_TRAIN_PAT_1		(0 << 28)
+#define   DP_LINK_TRAIN_PAT_2		(1 << 28)
+#define   DP_LINK_TRAIN_PAT_IDLE	(2 << 28)
+#define   DP_LINK_TRAIN_OFF		(3 << 28)
+#define   DP_LINK_TRAIN_MASK		(3 << 28)
+#define   DP_LINK_TRAIN_SHIFT		28
+
+/* Signal voltages. These are mostly controlled by the other end */
+#define   DP_VOLTAGE_0_4		(0 << 25)
+#define   DP_VOLTAGE_0_6		(1 << 25)
+#define   DP_VOLTAGE_0_8		(2 << 25)
+#define   DP_VOLTAGE_1_2		(3 << 25)
+#define   DP_VOLTAGE_MASK		(7 << 25)
+#define   DP_VOLTAGE_SHIFT		25
+
+/* Signal pre-emphasis levels, like voltages, the other end tells us what
+ * they want
+ */
+#define   DP_PRE_EMPHASIS_0		(0 << 22)
+#define   DP_PRE_EMPHASIS_3_5		(1 << 22)
+#define   DP_PRE_EMPHASIS_6		(2 << 22)
+#define   DP_PRE_EMPHASIS_9_5		(3 << 22)
+#define   DP_PRE_EMPHASIS_MASK		(7 << 22)
+#define   DP_PRE_EMPHASIS_SHIFT		22
+
+/* How many wires to use. I guess 3 was too hard */
+#define   DP_PORT_WIDTH_1		(0 << 19)
+#define   DP_PORT_WIDTH_2		(1 << 19)
+#define   DP_PORT_WIDTH_4		(3 << 19)
+#define   DP_PORT_WIDTH_MASK		(7 << 19)
+
+/* Mystic DPCD version 1.1 special mode */
+#define   DP_ENHANCED_FRAMING		(1 << 18)
+
+/** locked once port is enabled */
+#define   DP_PORT_REVERSAL		(1 << 15)
+
+/** sends the clock on lane 15 of the PEG for debug */
+#define   DP_CLOCK_OUTPUT_ENABLE	(1 << 13)
+
+#define   DP_SCRAMBLING_DISABLE		(1 << 12)
+#define   DP_SCRAMBLING_DISABLE_IRONLAKE	(1 << 7)
+
+/** limit RGB values to avoid confusing TVs */
+#define   DP_COLOR_RANGE_16_235		(1 << 8)
+
+/** Turn on the audio link */
+#define   DP_AUDIO_OUTPUT_ENABLE	(1 << 6)
+
+/** vs and hs sync polarity */
+#define   DP_SYNC_VS_HIGH		(1 << 4)
+#define   DP_SYNC_HS_HIGH		(1 << 3)
+
+/** A fantasy */
+#define   DP_DETECTED			(1 << 2)
+
+/** The aux channel provides a way to talk to the
+ * signal sink for DDC etc. Max packet size supported
+ * is 20 bytes in each direction, hence the 5 fixed
+ * data registers
+ */
+#define DPB_AUX_CH_CTL			0x64110
+#define DPB_AUX_CH_DATA1		0x64114
+#define DPB_AUX_CH_DATA2		0x64118
+#define DPB_AUX_CH_DATA3		0x6411c
+#define DPB_AUX_CH_DATA4		0x64120
+#define DPB_AUX_CH_DATA5		0x64124
+
+#define DPC_AUX_CH_CTL			0x64210
+#define DPC_AUX_CH_DATA1		0x64214
+#define DPC_AUX_CH_DATA2		0x64218
+#define DPC_AUX_CH_DATA3		0x6421c
+#define DPC_AUX_CH_DATA4		0x64220
+#define DPC_AUX_CH_DATA5		0x64224
+
+#define   DP_AUX_CH_CTL_SEND_BUSY	    (1 << 31)
+#define   DP_AUX_CH_CTL_DONE		    (1 << 30)
+#define   DP_AUX_CH_CTL_INTERRUPT	    (1 << 29)
+#define   DP_AUX_CH_CTL_TIME_OUT_ERROR	    (1 << 28)
+#define   DP_AUX_CH_CTL_TIME_OUT_400us	    (0 << 26)
+#define   DP_AUX_CH_CTL_TIME_OUT_600us	    (1 << 26)
+#define   DP_AUX_CH_CTL_TIME_OUT_800us	    (2 << 26)
+#define   DP_AUX_CH_CTL_TIME_OUT_1600us	    (3 << 26)
+#define   DP_AUX_CH_CTL_TIME_OUT_MASK	    (3 << 26)
+#define   DP_AUX_CH_CTL_RECEIVE_ERROR	    (1 << 25)
+#define   DP_AUX_CH_CTL_MESSAGE_SIZE_MASK    (0x1f << 20)
+#define   DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT   20
+#define   DP_AUX_CH_CTL_PRECHARGE_2US_MASK   (0xf << 16)
+#define   DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT  16
+#define   DP_AUX_CH_CTL_AUX_AKSV_SELECT	    (1 << 15)
+#define   DP_AUX_CH_CTL_MANCHESTER_TEST	    (1 << 14)
+#define   DP_AUX_CH_CTL_SYNC_TEST	    (1 << 13)
+#define   DP_AUX_CH_CTL_DEGLITCH_TEST	    (1 << 12)
+#define   DP_AUX_CH_CTL_PRECHARGE_TEST	    (1 << 11)
+#define   DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK    (0x7ff)
+#define   DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT   0
+
+/*
+ * Computing GMCH M and N values for the Display Port link
+ *
+ * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes
+ *
+ * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz)
+ *
+ * The GMCH value is used internally
+ *
+ * bytes_per_pixel is the number of bytes coming out of the plane,
+ * which is after the LUTs, so we want the bytes for our color format.
+ * For our current usage, this is always 3, one byte for R, G and B.
+ */
+
+#define _PIPEA_GMCH_DATA_M			0x70050
+#define _PIPEB_GMCH_DATA_M			0x71050
+
+/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */
+#define   PIPE_GMCH_DATA_M_TU_SIZE_MASK		(0x3f << 25)
+#define   PIPE_GMCH_DATA_M_TU_SIZE_SHIFT	25
+
+#define   PIPE_GMCH_DATA_M_MASK			(0xffffff)
+
+#define _PIPEA_GMCH_DATA_N			0x70054
+#define _PIPEB_GMCH_DATA_N			0x71054
+#define   PIPE_GMCH_DATA_N_MASK			(0xffffff)
+
+/*
+ * Computing Link M and N values for the Display Port link
+ *
+ * Link M / N = pixel_clock / ls_clk
+ *
+ * (the DP spec calls pixel_clock the 'strm_clk')
+ *
+ * The Link value is transmitted in the Main Stream
+ * Attributes and VB-ID.
+ */
+
+#define _PIPEA_DP_LINK_M				0x70060
+#define _PIPEB_DP_LINK_M				0x71060
+#define   PIPEA_DP_LINK_M_MASK			(0xffffff)
+
+#define _PIPEA_DP_LINK_N				0x70064
+#define _PIPEB_DP_LINK_N				0x71064
+#define   PIPEA_DP_LINK_N_MASK			(0xffffff)
+
+#define PIPE_GMCH_DATA_M(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_M, _PIPEB_GMCH_DATA_M)
+#define PIPE_GMCH_DATA_N(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_N, _PIPEB_GMCH_DATA_N)
+#define PIPE_DP_LINK_M(pipe) _PIPE(pipe, _PIPEA_DP_LINK_M, _PIPEB_DP_LINK_M)
+#define PIPE_DP_LINK_N(pipe) _PIPE(pipe, _PIPEA_DP_LINK_N, _PIPEB_DP_LINK_N)
+
+#define   PIPE_BPC_MASK				(7 << 5)
+#define   PIPE_8BPC				(0 << 5)
+#define   PIPE_10BPC				(1 << 5)
+#define   PIPE_6BPC				(2 << 5)
+
+#endif