diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power/supply')
56 files changed, 2777 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt new file mode 100644 index 000000000..f181e46d8 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt @@ -0,0 +1,16 @@ +=== AB8500 Battery Temperature Monitor Driver === + +The properties below describes the node for btemp driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-btemp" +- battery = Shall be battery specific information + + Example: + ab8500_btemp { + compatible = "stericsson,ab8500-btemp"; + battery = <&ab8500_battery>; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt new file mode 100644 index 000000000..56636f927 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt @@ -0,0 +1,16 @@ +=== AB8500 Charging Algorithm Driver === + +The properties below describes the node for chargalg driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-chargalg" +- battery = Shall be battery specific information + +Example: +ab8500_chargalg { + compatible = "stericsson,ab8500-chargalg"; + battery = <&ab8500_battery>; +}; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt new file mode 100644 index 000000000..24ada03e0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt @@ -0,0 +1,25 @@ +=== AB8500 Charger Driver === + +Required Properties: +- compatible = Shall be "stericsson,ab8500-charger" +- battery = Shall be battery specific information + Example: + ab8500_charger { + compatible = "stericsson,ab8500-charger"; + battery = <&ab8500_battery>; + }; + +- vddadc-supply: Supply for USB and Main charger + Example: + ab8500-charger { + vddadc-supply = <&ab8500_ldo_tvout_reg>; + } +- autopower_cfg: + Boolean value depicting the presence of 'automatic poweron after powerloss' + Example: + ab8500-charger { + autopower_cfg; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt new file mode 100644 index 000000000..ccafcb911 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt @@ -0,0 +1,58 @@ +=== AB8500 Fuel Gauge Driver === + +AB8500 is a mixed signal multimedia and power management +device comprising: power and energy-management-module, +wall-charger, usb-charger, audio codec, general purpose adc, +tvout, clock management and sim card interface. + +Fuelgauge support is part of energy-management-modules, other +components of this module are: +main-charger, usb-combo-charger and battery-temperature-monitoring. + +The properties below describes the node for fuelgauge driver. + +Required Properties: +- compatible = This shall be: "stericsson,ab8500-fg" +- battery = Shall be battery specific information + Example: + ab8500_fg { + compatible = "stericsson,ab8500-fg"; + battery = <&ab8500_battery>; + }; + +dependent node: + ab8500_battery: ab8500_battery { + }; + This node will provide information on 'thermistor interface' and + 'battery technology type' used. + +Properties of this node are: +thermistor-on-batctrl: + A boolean value indicating thermistor interface to battery + + Note: + 'btemp' and 'batctrl' are the pins interfaced for battery temperature + measurement, 'btemp' signal is used when NTC(negative temperature + coefficient) resister is interfaced external to battery whereas + 'batctrl' pin is used when NTC resister is internal to battery. + + Example: + ab8500_battery: ab8500_battery { + thermistor-on-batctrl; + }; + indicates: NTC resister is internal to battery, 'batctrl' is used + for thermal measurement. + + The absence of property 'thermal-on-batctrl' indicates + NTC resister is external to battery and 'btemp' signal is used + for thermal measurement. + +battery-type: + This shall be the battery manufacturing technology type, + allowed types are: + "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn" + Example: + ab8500_battery: ab8500_battery { + stericsson,battery-type = "LIPO"; + } + diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt new file mode 100644 index 000000000..cb737a9e1 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt @@ -0,0 +1,44 @@ +Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a-charger". + - active-semi,chglev-gpios: charge current level phandle with args + as described in ../gpio/gpio.txt. + - active-semi,lbo-gpios: specify the low battery voltage detect phandle + with args as as described in ../gpio/gpio.txt. + - interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. + +Optional properties: + - active-semi,input-voltage-threshold-microvolt: unit: mV; + Specifies the charger's input over-voltage threshold value; + The value can be: 6600, 7000, 7500, 8000; default: 6600 + - active-semi,precondition-timeout: unit: minutes; + Specifies the charger's PRECONDITION safety timer setting value; + The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; + default: 40. + - active-semi,total-timeout: unit: hours; + Specifies the charger's total safety timer setting value; + The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; + default: 3. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 IRQ_TYPE_LEVEL_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt new file mode 100644 index 000000000..7a1fb532a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt @@ -0,0 +1,25 @@ +AXP20X and AXP22X PMICs' AC power supply + +Required Properties: + - compatible: One of: + "x-powers,axp202-ac-power-supply" + "x-powers,axp221-ac-power-supply" + "x-powers,axp813-ac-power-supply" + +This node is a subnode of the axp20x PMIC. + +The AXP20X can read the current current and voltage supplied by AC by +reading ADC channels from the AXP20X ADC. + +The AXP22X is only able to tell if an AC power supply is present and +usable. + +AXP813/AXP803 are able to limit current and supply voltage + +Example: + +&axp209 { + ac_power_supply: ac-power-supply { + compatible = "x-powers,axp202-ac-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt new file mode 100644 index 000000000..41916f699 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt @@ -0,0 +1,20 @@ +AXP20x and AXP22x battery power supply + +Required Properties: + - compatible, one of: + "x-powers,axp209-battery-power-supply" + "x-powers,axp221-battery-power-supply" + "x-powers,axp813-battery-power-supply" + +This node is a subnode of its respective PMIC DT node. + +The supported devices can read the battery voltage, charge and discharge +currents of the battery by reading ADC channels from the ADC. + +Example: + +&axp209 { + battery_power_supply: battery-power-supply { + compatible = "x-powers,axp209-battery-power-supply"; + } +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt new file mode 100644 index 000000000..b2d4968fd --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt @@ -0,0 +1,41 @@ +AXP20x USB power supply + +Required Properties: +-compatible: One of: "x-powers,axp202-usb-power-supply" + "x-powers,axp221-usb-power-supply" + "x-powers,axp223-usb-power-supply" + "x-powers,axp813-usb-power-supply" + +The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight +variations such as the former being able to set the VBUS power supply max +current to 100mA, unlike the latter. + +This node is a subnode of the axp20x PMIC. + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + ... + }; + + usb-power-supply: usb-power-supply { + compatible = "x-powers,axp202-usb-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt new file mode 100644 index 000000000..a9f80cc49 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/battery.txt @@ -0,0 +1,3 @@ +The contents of this file has been moved to battery.yaml + +Please note that not all charger drivers respect all of the properties. diff --git a/Documentation/devicetree/bindings/power/supply/battery.yaml b/Documentation/devicetree/bindings/power/supply/battery.yaml new file mode 100644 index 000000000..0c7e2e447 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/battery.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Battery Characteristics + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: | + The devicetree battery node provides static battery characteristics. + In smart batteries, these are typically stored in non-volatile memory + on a fuel gauge chip. The battery node should be used where there is + no appropriate non-volatile memory, or it is unprogrammed/incorrect. + + Upstream dts files should not include battery nodes, unless the battery + represented cannot easily be replaced in the system by one of a + different type. This prevents unpredictable, potentially harmful, + behavior should a replacement that changes the battery type occur + without a corresponding update to the dtb. + + Battery properties are named, where possible, for the corresponding elements + in enum power_supply_property, defined in include/linux/power_supply.h + + Batteries must be referenced by chargers and/or fuel-gauges using a phandle. + The phandle's property should be named "monitored-battery". + +properties: + compatible: + const: simple-battery + + over-voltage-threshold-microvolt: + description: battery over-voltage limit + + re-charge-voltage-microvolt: + description: limit to automatically start charging again + + voltage-min-design-microvolt: + description: drained battery voltage + + voltage-max-design-microvolt: + description: fully charged battery voltage + + energy-full-design-microwatt-hours: + description: battery design energy + + charge-full-design-microamp-hours: + description: battery design capacity + + trickle-charge-current-microamp: + description: current for trickle-charge phase + + precharge-current-microamp: + description: current for pre-charge phase + + precharge-upper-limit-microvolt: + description: limit when to change to constant charging + + charge-term-current-microamp: + description: current for charge termination phase + + constant-charge-current-max-microamp: + description: maximum constant input current + + constant-charge-voltage-max-microvolt: + description: maximum constant input voltage + + factory-internal-resistance-micro-ohms: + description: battery factory internal resistance + + resistance-temp-table: + description: | + An array providing the temperature in degree Celsius + and corresponding battery internal resistance percent, which is used to + look up the resistance percent according to current temperature to get an + accurate batterty internal resistance in different temperatures. + + ocv-capacity-celsius: + description: | + An array containing the temperature in degree Celsius, + for each of the battery capacity lookup table. + + operating-range-celsius: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: operating temperature range of a battery + items: + - description: minimum temperature at which battery can operate + - description: maximum temperature at which battery can operate + + ambient-celsius: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: safe range of ambient temperature + items: + - description: alert when ambient temperature is lower than this value + - description: alert when ambient temperature is higher than this value + + alert-celsius: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: safe range of battery temperature + items: + - description: alert when battery temperature is lower than this value + - description: alert when battery temperature is higher than this value + +required: + - compatible + +patternProperties: + '^ocv-capacity-table-[0-9]+$': + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: | + An array providing the open circuit voltage (OCV) + of the battery and corresponding battery capacity percent, which is used + to look up battery capacity according to current OCV value. And the open + circuit voltage unit is microvolt. + maxItems: 100 + items: + items: + - description: open circuit voltage (OCV) in microvolts + - description: battery capacity percent + maximum: 100 + +additionalProperties: false + +examples: + - | + power { + #address-cells = <1>; + #size-cells = <0>; + + battery: battery { + compatible = "simple-battery"; + over-voltage-threshold-microvolt = <4500000>; + re-charge-voltage-microvolt = <250000>; + voltage-min-design-microvolt = <3200000>; + voltage-max-design-microvolt = <4200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + precharge-current-microamp = <256000>; + precharge-upper-limit-microvolt = <2500000>; + charge-term-current-microamp = <128000>; + constant-charge-current-max-microamp = <900000>; + constant-charge-voltage-max-microvolt = <4200000>; + factory-internal-resistance-micro-ohms = <250000>; + ocv-capacity-celsius = <(-10) 0 10>; + /* table for -10 degree Celsius */ + ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>; + /* table for 0 degree Celsius */ + ocv-capacity-table-1 = <4200000 100>, <4185000 95>, <4113000 90>; + /* table for 10 degree Celsius */ + ocv-capacity-table-2 = <4250000 100>, <4200000 95>, <4185000 90>; + resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>; + operating-range-celsius = <(-30) 50>; + ambient-celsius = <(-5) 50>; + alert-celsius = <0 40>; + }; + + charger@11 { + reg = <0x11>; + monitored-battery = <&battery>; + }; + + fuel-gauge@22 { + reg = <0x22>; + monitored-battery = <&battery>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq2415x.txt b/Documentation/devicetree/bindings/power/supply/bq2415x.txt new file mode 100644 index 000000000..d0327f0b5 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq2415x.txt @@ -0,0 +1,47 @@ +Binding for TI bq2415x Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24150" + * "ti,bq24150" + * "ti,bq24150a" + * "ti,bq24151" + * "ti,bq24151a" + * "ti,bq24152" + * "ti,bq24153" + * "ti,bq24153a" + * "ti,bq24155" + * "ti,bq24156" + * "ti,bq24156a" + * "ti,bq24158" +- reg: integer, i2c address of the device. +- ti,current-limit: integer, initial maximum current charger can pull + from power supply in mA. +- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV. + The chip will use slow precharge if battery voltage + is below this value. +- ti,battery-regulation-voltage: integer, maximum charging voltage in mV. +- ti,charge-current: integer, maximum charging current in mA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in mA). +- ti,resistor-sense: integer, value of sensing resistor in milliohm. + +Optional properties: +- ti,usb-charger-detection: phandle to usb charger detection device. + (required for auto mode) + +Example from Nokia N900: + +bq24150a { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt new file mode 100644 index 000000000..ffe2be408 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24190.txt @@ -0,0 +1,61 @@ +TI BQ24190 Li-Ion Battery Charger + +Required properties: +- compatible: contains one of the following: + * "ti,bq24190" + * "ti,bq24192" + * "ti,bq24192i" + * "ti,bq24196" +- reg: integer, I2C address of the charger. +- interrupts[-extended]: configuration for charger INT pin. + +Optional properties: +- monitored-battery: phandle of battery characteristics devicetree node + The charger uses the following battery properties: + + precharge-current-microamp: maximum charge current during precharge + phase (typically 20% of battery capacity). + + charge-term-current-microamp: a charge cycle terminates when the + battery voltage is above recharge threshold, and the current is below + this setting (typically 10% of battery capacity). + See also Documentation/devicetree/bindings/power/supply/battery.txt +- ti,system-minimum-microvolt: when power is connected and the battery is below + minimum system voltage, the system will be regulated above this setting. + +child nodes: +- usb-otg-vbus: + Usage: optional + Description: Regulator that is used to control the VBUS voltage direction for + either USB host mode or for charging on the OTG port. + +Notes: +- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default + charge current on USB SDP ports, among other features). To simulate this on + boards that wire the pin to a GPIO, set a gpio-hog. + +Example: + + bat: battery { + compatible = "simple-battery"; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + // etc. + }; + + bq24190: charger@6a { + compatible = "ti,bq24190"; + reg = <0x6a>; + interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>; + monitored-battery = <&bat>; + ti,system-minimum-microvolt = <3200000>; + + usb_otg_vbus: usb-otg-vbus { }; + }; + + &twl_gpio { + otg { + gpio-hog; + gpios = <6 0>; + output-high; + line-name = "otg-gpio"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt new file mode 100644 index 000000000..f8f5a1685 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24257.txt @@ -0,0 +1,62 @@ +Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24250" + * "ti,bq24251" + * "ti,bq24257" +- reg: integer, i2c address of the device. +- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in + conjunction with "interrupt-parent". +- ti,battery-regulation-voltage: integer, maximum charging voltage in uV. +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Optional properties: +- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. +- ti,current-limit: The maximum current to be drawn from the charger's input + (in uA). If this property is not specified, the input limit current is + set automatically using USB D+/D- signal based charger type detection. + If the hardware does not support the D+/D- based detection, a default + of 500,000 is used (=500mA) instead. +- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If + not specified a default of 6,5000,000 (=6.5V) is used. +- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic + power path management (in uV). If not specified a default of 4,360,000 + (=4.36V) is used. + +Example: + +bq24257 { + compatible = "ti,bq24257"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; +}; + +Example: + +bq24250 { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml new file mode 100644 index 000000000..75a56773b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI bq2515x 500-mA Linear charger family + +maintainers: + - Dan Murphy <dmurphy@ti.com> + - Ricardo Rivera-Matos <r-rivera-matos@ti.com> + +description: | + The BQ2515x family is a highly integrated battery charge management IC that + integrates the most common functions for wearable devices, namely a charger, + an output voltage rail, ADC for battery and system monitoring, and + push-button controller. + + Specifications about the charger can be found at: + http://www.ti.com/lit/ds/symlink/bq25150.pdf + http://www.ti.com/lit/ds/symlink/bq25155.pdf + +properties: + compatible: + enum: + - ti,bq25150 + - ti,bq25155 + + reg: + maxItems: 1 + description: I2C address of the charger. + + ac-detect-gpios: + description: | + GPIO used for connecting the bq2515x device PG (AC Detect) + pin. + maxItems: 1 + + reset-gpios: + description: GPIO used for hardware reset. + maxItems: 1 + + powerdown-gpios: + description: GPIO used for low power mode of IC. + maxItems: 1 + + charge-enable-gpios: + description: GPIO used to turn on and off charging. + maxItems: 1 + + input-current-limit-microamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximum input current in micro Amps. + minimum: 50000 + maximum: 500000 + + monitored-battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the battery node being monitored + +required: + - compatible + - reg + - monitored-battery + +additionalProperties: false + +examples: + - | + bat: battery { + compatible = "simple-battery"; + constant-charge-current-max-microamp = <50000>; + precharge-current-microamp = <2500>; + constant-charge-voltage-max-microvolt = <4000000>; + }; + #include <dt-bindings/gpio/gpio.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + bq25150: charger@6b { + compatible = "ti,bq25150"; + reg = <0x6b>; + monitored-battery = <&bat>; + input-current-limit-microamp = <100000>; + + ac-detect-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + powerdown-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt new file mode 100644 index 000000000..805040c6f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt @@ -0,0 +1,60 @@ +Binding for TI bq25890 Li-Ion Charger + +This driver will support the bq25892, the bq25896 and the bq25890. There are +other ICs in the same family but those have not been tested. + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq25890" + * "ti,bq25892" + * "ti,bq25895" + * "ti,bq25896" +- reg: integer, i2c address of the device. +- interrupts: interrupt line; +- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV); +- ti,charge-current: integer, maximum charging current (in uA); +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA); +- ti,precharge-current: integer, maximum charge current during precharge + phase (in uA); +- ti,minimum-sys-voltage: integer, when battery is charging and it is below + minimum system voltage, the system will be regulated above + minimum-sys-voltage setting (in uV); +- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV); +- ti,boost-max-current: integer, maximum allowed current draw in boost mode + (in uA). + +Optional properties: +- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz, + otherwise 1.5MHz; +- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the + input current will be the lower between the resistor setting and the IINLIM + register setting; +- ti,thermal-regulation-threshold: integer, temperature above which the charge + current is lowered, to avoid overheating (in degrees Celsius). If omitted, + the default setting will be used (120 degrees); +- ti,ibatcomp-micro-ohms: integer, value of a resistor in series with + the battery; +- ti,ibatcomp-clamp-microvolt: integer, maximum charging voltage adjustment due + to expected voltage drop on in-series resistor; + +Example: + +bq25890 { + compatible = "ti,bq25890"; + reg = <0x6a>; + + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_FALLING>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; + ti,precharge-current = <128000>; + ti,minimum-sys-voltage = <3600000>; + ti,boost-voltage = <5000000>; + ti,boost-max-current = <1000000>; + + ti,use-ilim-pin; + ti,thermal-regulation-threshold = <120>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/bq25980.yaml b/Documentation/devicetree/bindings/power/supply/bq25980.yaml new file mode 100644 index 000000000..f6b3dd409 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq25980.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq25980.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI BQ25980 Flash Charger + +maintainers: + - Dan Murphy <dmurphy@ti.com> + - Ricardo Rivera-Matos <r-rivera-matos@ti.com> + +description: | + The BQ25980, BQ25975, and BQ25960 are a series of flash chargers intended + for use in high-power density portable electronics. These inductorless + switching chargers can provide over 97% efficiency by making use of the + switched capacitor architecture. + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq25980 + - ti,bq25975 + - ti,bq25960 + + reg: + maxItems: 1 + + ti,watchdog-timeout-ms: + description: | + Watchdog timer in milli seconds. 0 disables the watchdog. + default: 0 + minimum: 0 + maximum: 300000 + enum: [ 0, 5000, 10000, 50000, 300000] + + ti,sc-ovp-limit-microvolt: + description: | + Minimum input voltage limit in micro volts with a when the charger is in + switch cap mode. 100000 micro volt step. + default: 17800000 + minimum: 14000000 + maximum: 22000000 + + ti,sc-ocp-limit-microamp: + description: | + Maximum input current limit in micro amps with a 100000 micro amp step. + minimum: 100000 + maximum: 3300000 + + ti,bypass-ovp-limit-microvolt: + description: | + Minimum input voltage limit in micro volts with a when the charger is in + switch cap mode. 50000 micro volt step. + minimum: 7000000 + maximum: 12750000 + + ti,bypass-ocp-limit-microamp: + description: | + Maximum input current limit in micro amps with a 100000 micro amp step. + minimum: 100000 + maximum: 3300000 + + ti,bypass-enable: + type: boolean + description: Enables bypass mode at boot time + + interrupts: + description: | + Indicates that the device state has changed. + + monitored-battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the battery node being monitored + +required: + - compatible + - reg + - monitored-battery + +unevaluatedProperties: false + +examples: + - | + bat: battery { + compatible = "simple-battery"; + constant-charge-current-max-microamp = <4000000>; + constant-charge-voltage-max-microvolt = <8400000>; + precharge-current-microamp = <160000>; + charge-term-current-microamp = <160000>; + }; + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + bq25980: charger@65 { + compatible = "ti,bq25980"; + reg = <0x65>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_FALLING>; + ti,watchdog-timer = <0>; + ti,sc-ocp-limit-microamp = <2000000>; + ti,sc-ovp-limit-microvolt = <17800000>; + monitored-battery = <&bat>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml new file mode 100644 index 000000000..45beefccf --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq27xxx.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI BQ27XXX fuel gauge family + +maintainers: + - Pali Rohár <pali@kernel.org> + - Andrew F. Davis <afd@ti.com> + - Sebastian Reichel <sre@kernel.org> + +description: | + Support various Texas Instruments fuel gauge devices that share similar + register maps and power supply properties + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq27200 + - ti,bq27210 + - ti,bq27500 # deprecated, use revision specific property below + - ti,bq27510 # deprecated, use revision specific property below + - ti,bq27520 # deprecated, use revision specific property below + - ti,bq27500-1 + - ti,bq27510g1 + - ti,bq27510g2 + - ti,bq27510g3 + - ti,bq27520g1 + - ti,bq27520g2 + - ti,bq27520g3 + - ti,bq27520g4 + - ti,bq27521 + - ti,bq27530 + - ti,bq27531 + - ti,bq27541 + - ti,bq27542 + - ti,bq27546 + - ti,bq27742 + - ti,bq27545 + - ti,bq27411 + - ti,bq27421 + - ti,bq27425 + - ti,bq27426 + - ti,bq27441 + - ti,bq27621 + - ti,bq27z561 + - ti,bq28z610 + - ti,bq34z100 + + reg: + maxItems: 1 + description: integer, I2C address of the fuel gauge. + + monitored-battery: + description: | + phandle of battery characteristics node. + The fuel gauge uses the following battery properties: + - energy-full-design-microwatt-hours + - charge-full-design-microamp-hours + - voltage-min-design-microvolt + Both or neither of the *-full-design-*-hours properties must be set. + See Documentation/devicetree/bindings/power/supply/battery.txt + + power-supplies: true + +required: + - compatible + - reg +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + }; + + bq27510g3: fuel-gauge@55 { + compatible = "ti,bq27510g3"; + reg = <0x55>; + monitored-battery = <&bat>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/charger-manager.txt b/Documentation/devicetree/bindings/power/supply/charger-manager.txt new file mode 100644 index 000000000..b5ae9061b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/charger-manager.txt @@ -0,0 +1,91 @@ +charger-manager bindings +~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "charger-manager" + - <>-supply : for regulator consumer, named according to cm-regulator-name + - cm-chargers : name of chargers + - cm-fuel-gauge : name of battery fuel gauge + - subnode <regulator> : + - cm-regulator-name : name of charger regulator + - subnode <cable> : + - cm-cable-name : name of charger cable - one of USB, USB-HOST, + SDP, DCP, CDP, ACA, FAST-CHARGER, SLOW-CHARGER, WPT, + PD, DOCK, JIG, or MECHANICAL + - cm-cable-extcon : name of extcon dev +(optional) - cm-cable-min : minimum current of cable +(optional) - cm-cable-max : maximum current of cable + +Optional properties : + - cm-name : charger manager's name (default : "battery") + - cm-poll-mode : polling mode - 0 for disabled, 1 for always, 2 for when + external power is connected, or 3 for when charging. If not present, + then polling is disabled + - cm-poll-interval : polling interval (in ms) + - cm-battery-stat : battery status - 0 for battery always present, 1 for no + battery, 2 to check presence via fuel gauge, or 3 to check presence + via charger + - cm-fullbatt-vchkdrop-volt : voltage drop (in uV) before restarting charging + - cm-fullbatt-voltage : voltage (in uV) of full battery + - cm-fullbatt-soc : state of charge to consider as full battery + - cm-fullbatt-capacity : capcity (in uAh) to consider as full battery + - cm-thermal-zone : name of external thermometer's thermal zone + - cm-battery-* : threshold battery temperature for charging + -cold : critical cold temperature of battery for charging + -cold-in-minus : flag that cold temperature is in minus degrees + -hot : critical hot temperature of battery for charging + -temp-diff : temperature difference to allow recharging + - cm-dis/charging-max = limits of charging duration + +Deprecated properties: + - cm-num-chargers + - cm-fullbatt-vchkdrop-ms + +Example : + charger-manager@0 { + compatible = "charger-manager"; + chg-reg-supply = <&charger_regulator>; + + cm-name = "battery"; + /* Always polling ON : 30s */ + cm-poll-mode = <1>; + cm-poll-interval = <30000>; + + cm-fullbatt-vchkdrop-volt = <150000>; + cm-fullbatt-soc = <100>; + + cm-battery-stat = <3>; + + cm-chargers = "charger0", "charger1", "charger2"; + + cm-fuel-gauge = "fuelgauge0"; + + cm-thermal-zone = "thermal_zone.1" + /* in deci centigrade */ + cm-battery-cold = <50>; + cm-battery-cold-in-minus; + cm-battery-hot = <800>; + cm-battery-temp-diff = <100>; + + /* Allow charging for 5hr */ + cm-charging-max = <18000000>; + /* Allow discharging for 2hr */ + cm-discharging-max = <7200000>; + + regulator@0 { + cm-regulator-name = "chg-reg"; + cable@0 { + cm-cable-name = "USB"; + cm-cable-extcon = "extcon-dev.0"; + cm-cable-min = <475000>; + cm-cable-max = <500000>; + }; + cable@1 { + cm-cable-name = "SDP"; + cm-cable-extcon = "extcon-dev.0"; + cm-cable-min = <650000>; + cm-cable-max = <675000>; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt new file mode 100644 index 000000000..a04efa22d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt @@ -0,0 +1,31 @@ +Motorola CPCAP PMIC battery driver binding + +Required properties: +- compatible: Shall be "motorola,cpcap-battery" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "lowbph", "lowbpl", "chrgcurr1", "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "chg_isense", "batti" +- power-supplies: List of phandles for power-supplying devices, as + described in power_supply.txt. Typically a reference + to cpcap_charger. + +Example: + +cpcap_battery: battery { + compatible = "motorola,cpcap-battery"; + interrupts-extended = < + &cpcap 5 0 &cpcap 3 0 + &cpcap 20 0 &cpcap 54 0 + >; + interrupt-names = + "lowbph", "lowbpl", + "chrgcurr1", "battdetb"; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 5 &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "chg_isense", "batti"; + power-supplies = <&cpcap_charger>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt new file mode 100644 index 000000000..6048f6367 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt @@ -0,0 +1,40 @@ +Motorola CPCAP PMIC battery charger binding + +Required properties: +- compatible: Shall be "motorola,mapphone-cpcap-charger" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld", + "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "vbus", "chg_isense", "batti" + +Optional properties: +- mode-gpios: Optionally CPCAP charger can have a companion wireless + charge controller that is controlled with two GPIOs + that are active low. + +Example: + +cpcap_charger: charger { + compatible = "motorola,mapphone-cpcap-charger"; + interrupts-extended = < + &cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0 + &cpcap 22 0 &cpcap 21 0 &cpcap 20 0 &cpcap 19 0 + &cpcap 54 0 + >; + interrupt-names = + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld", + "battdetb"; + mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW + &gpio3 23 GPIO_ACTIVE_LOW>; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 2 &cpcap_adc 5 + &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "vbus", "chg_isense", + "batti"; +}; diff --git a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml new file mode 100644 index 000000000..ee92e6a07 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/cw2015_battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Battery driver for CW2015 shuntless fuel gauge by CellWise. + +maintainers: + - Tobias Schramm <t.schramm@manjaro.org> + +description: | + The driver can utilize information from a simple-battery linked via a + phandle in monitored-battery. If specified the driver uses the + charge-full-design-microamp-hours property of the battery. + +properties: + compatible: + const: cellwise,cw2015 + + reg: + maxItems: 1 + + cellwise,battery-profile: + description: | + This property specifies characteristics of the battery used. The format + of this binary blob is kept secret by CellWise. The only way to obtain + it is to mail two batteries to a test facility of CellWise and receive + back a test report with the binary blob. + $ref: /schemas/types.yaml#definitions/uint8-array + minItems: 64 + maxItems: 64 + + cellwise,monitor-interval-ms: + description: + Specifies the interval in milliseconds gauge values are polled at + minimum: 250 + + power-supplies: + description: + Specifies supplies used for charging the battery connected to this gauge + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 1 + maxItems: 8 # Should be enough + + monitored-battery: + description: + Specifies the phandle of a simple-battery connected to this gauge + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + cw2015@62 { + compatible = "cellwise,cw201x"; + reg = <0x62>; + cellwise,battery-profile = /bits/ 8 < + 0x17 0x67 0x80 0x73 0x6E 0x6C 0x6B 0x63 + 0x77 0x51 0x5C 0x58 0x50 0x4C 0x48 0x36 + 0x15 0x0C 0x0C 0x19 0x5B 0x7D 0x6F 0x69 + 0x69 0x5B 0x0C 0x29 0x20 0x40 0x52 0x59 + 0x57 0x56 0x54 0x4F 0x3B 0x1F 0x7F 0x17 + 0x06 0x1A 0x30 0x5A 0x85 0x93 0x96 0x2D + 0x48 0x77 0x9C 0xB3 0x80 0x52 0x94 0xCB + 0x2F 0x00 0x64 0xA5 0xB5 0x11 0xF0 0x11 + >; + cellwise,monitor-interval-ms = <5000>; + monitored-battery = <&bat>; + power-supplies = <&mains_charger>, <&usb_charger>; + }; + }; + diff --git a/Documentation/devicetree/bindings/power/supply/da9150-charger.txt b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt new file mode 100644 index 000000000..f3906663c --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt @@ -0,0 +1,26 @@ +Dialog Semiconductor DA9150 Charger Power Supply bindings + +Required properties: +- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply + +Optional properties: +- io-channels: List of phandle and IIO specifier pairs +- io-channel-names: List of channel names used by charger + ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"] + (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info) + + +Example: + + da9150-charger { + compatible = "dlg,da9150-charger"; + + io-channels = <&gpadc 0>, + <&gpadc 2>, + <&gpadc 8>, + <&gpadc 5>; + io-channel-names = "CHAN_IBUS", + "CHAN_VBUS", + "CHAN_TJUNC", + "CHAN_VBAT"; + }; diff --git a/Documentation/devicetree/bindings/power/supply/da9150-fg.txt b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt new file mode 100644 index 000000000..00236fe3e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt @@ -0,0 +1,23 @@ +Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings + +Required properties: +- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply + +Optional properties: +- dlg,update-interval: Interval time (milliseconds) between battery level checks. +- dlg,warn-soc-level: Battery discharge level (%) where warning event raised. + [1 - 100] +- dlg,crit-soc-level: Battery discharge level (%) where critical event raised. + This value should be lower than the warning level. + [1 - 100] + + +Example: + + fuel-gauge { + compatible = "dlg,da9150-fuel-gauge"; + + dlg,update-interval = <10000>; + dlg,warn-soc-level = /bits/ 8 <15>; + dlg,crit-soc-level = /bits/ 8 <5>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/gpio-charger.yaml b/Documentation/devicetree/bindings/power/supply/gpio-charger.yaml new file mode 100644 index 000000000..89f8e2bcb --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/gpio-charger.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/gpio-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: simple battery chargers only communicating through GPIOs + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: + This binding is for all chargers, which are working more or less + autonomously, only providing some status GPIOs and possibly some + GPIOs for limited control over the charging process. + +properties: + compatible: + const: gpio-charger + + charger-type: + enum: + - unknown + - battery + - ups + - mains + - usb-sdp # USB standard downstream port + - usb-dcp # USB dedicated charging port + - usb-cdp # USB charging downstream port + - usb-aca # USB accessory charger adapter + description: + Type of the charger, e.g. "mains" for a wall charger. + + gpios: + maxItems: 1 + description: GPIO indicating the charger presence + + charge-status-gpios: + maxItems: 1 + description: GPIO indicating the charging status + + charge-current-limit-gpios: + minItems: 1 + maxItems: 32 + description: GPIOs used for current limiting + + charge-current-limit-mapping: + description: List of tuples with current in uA and a GPIO bitmap (in + this order). The tuples must be provided in descending order of the + current limit. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: + Current limit in uA + - description: + Encoded GPIO setting. Bit 0 represents last GPIO from the + charge-current-limit-gpios property. Bit 1 second to last + GPIO and so on. + +required: + - compatible + +anyOf: + - required: + - gpios + - required: + - charge-status-gpios + - required: + - charge-current-limit-gpios + +dependencies: + charge-current-limit-gpios: [ charge-current-limit-mapping ] + charge-current-limit-mapping: [ charge-current-limit-gpios ] + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + charger { + compatible = "gpio-charger"; + charger-type = "usb-sdp"; + + gpios = <&gpd 28 GPIO_ACTIVE_LOW>; + charge-status-gpios = <&gpc 27 GPIO_ACTIVE_LOW>; + + charge-current-limit-gpios = <&gpioA 11 GPIO_ACTIVE_HIGH>, + <&gpioA 12 GPIO_ACTIVE_HIGH>; + charge-current-limit-mapping = <2500000 0x00>, // 2.5 A => both GPIOs low + <700000 0x01>, // 700 mA => GPIO A.12 high + <0 0x02>; // 0 mA => GPIO A.11 high + }; diff --git a/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml b/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml new file mode 100644 index 000000000..76c227a7c --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019-2020 Artur Rojek +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/ingenic,battery.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Ingenic JZ47xx battery bindings + +maintainers: + - Artur Rojek <contact@artur-rojek.eu> + +properties: + compatible: + oneOf: + - const: ingenic,jz4740-battery + - items: + - enum: + - ingenic,jz4725b-battery + - ingenic,jz4770-battery + - const: ingenic,jz4740-battery + + io-channels: + maxItems: 1 + + io-channel-names: + const: battery + + monitored-battery: + description: > + phandle to a "simple-battery" compatible node. + + This property must be a phandle to a node using the format described + in battery.yaml, with the following properties being required: + - voltage-min-design-microvolt: drained battery voltage, + - voltage-max-design-microvolt: fully charged battery voltage. + +required: + - compatible + - io-channels + - io-channel-names + - monitored-battery + +additionalProperties: false + +examples: + - | + #include <dt-bindings/iio/adc/ingenic,adc.h> + + simple_battery: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3600000>; + voltage-max-design-microvolt = <4200000>; + }; + + ingenic-battery { + compatible = "ingenic,jz4740-battery"; + io-channels = <&adc INGENIC_ADC_BATTERY>; + io-channel-names = "battery"; + monitored-battery = <&simple_battery>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/isp1704.txt b/Documentation/devicetree/bindings/power/supply/isp1704.txt new file mode 100644 index 000000000..fa3596907 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/isp1704.txt @@ -0,0 +1,17 @@ +Binding for NXP ISP1704 USB Charger Detection + +Required properties: +- compatible: Should contain one of the following: + * "nxp,isp1704" +- nxp,enable-gpio: Should contain a phandle + gpio-specifier + to the GPIO pin connected to the chip's enable pin. +- usb-phy: Should contain a phandle to the USB PHY + the ISP1704 is connected to. + +Example: + +isp1704 { + compatible = "nxp,isp1704"; + nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>; + usb-phy = <&usb2_phy>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt new file mode 100644 index 000000000..5485633b1 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt @@ -0,0 +1,21 @@ +LEGO MINDSTORMS EV3 Battery +~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery. +It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is +detected by a key switch in the battery compartment. + +Required properties: + - compatible: Must be "lego,ev3-battery" + - io-channels: phandles to analog inputs for reading voltage and current + - io-channel-names: Must be "voltage", "current" + - rechargeable-gpios: phandle to the rechargeable battery indication gpio + +Example: + + battery { + compatible = "lego,ev3-battery"; + io-channels = <&adc 4>, <&adc 3>; + io-channel-names = "voltage", "current"; + rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt new file mode 100644 index 000000000..0355a4b68 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt @@ -0,0 +1,43 @@ +Binding for TI/National Semiconductor LP8727 Charger + +Required properties: +- compatible: "ti,lp8727" +- reg: I2C slave address 27h + +Optional properties: +- interrupts: interrupt specifier (see interrupt binding[0]) +- debounce-ms: interrupt debounce time. (u32) + +AC and USB charging parameters +- charger-type: "ac" or "usb" (string) +- eoc-level: value of 'enum lp8727_eoc_level' (u8) +- charging-current: value of 'enum lp8727_ichg' (u8) + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example) + +lp8727@27 { + compatible = "ti,lp8727"; + reg = <0x27>; + + /* GPIO 134 is used for LP8728 interrupt pin */ + interrupt-parent = <&gpio5>; /* base = 128 */ + interrupts = <6 0x2>; /* offset = 6, falling edge type */ + + debounce-ms = <300>; + + /* AC charger: 5% EOC and 500mA charging current */ + ac { + charger-type = "ac"; + eoc-level = /bits/ 8 <0>; + charging-current = /bits/ 8 <4>; + }; + + /* USB charger: 10% EOC and 400mA charging current */ + usb { + charger-type = "usb"; + eoc-level = /bits/ 8 <1>; + charging-current = /bits/ 8 <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/lt3651-charger.txt b/Documentation/devicetree/bindings/power/supply/lt3651-charger.txt new file mode 100644 index 000000000..40811ff8d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lt3651-charger.txt @@ -0,0 +1,29 @@ +Analog Devices LT3651 Charger Power Supply bindings: lt3651-charger + +Required properties: +- compatible: Should contain one of the following: + * "lltc,ltc3651-charger", (DEPRECATED: Use "lltc,lt3651-charger") + * "lltc,lt3651-charger" + - lltc,acpr-gpios: Connect to ACPR output. See remark below. + +Optional properties: + - lltc,fault-gpios: Connect to FAULT output. See remark below. + - lltc,chrg-gpios: Connect to CHRG output. See remark below. + +The lt3651 outputs are open-drain type and active low. The driver assumes the +GPIO reports "active" when the output is asserted, so if the pins have been +connected directly, the GPIO flags should be set to active low also. + +The driver will attempt to aquire interrupts for all GPIOs to detect changes in +line state. If the system is not capabale of providing interrupts, the driver +cannot report changes and userspace will need to periodically read the sysfs +attributes to detect changes. + +Example: + + charger: battery-charger { + compatible = "lltc,lt3651-charger"; + lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>; + lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>; + lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt new file mode 100644 index 000000000..3b9ba147b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt @@ -0,0 +1,28 @@ +binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges + +All chips measure battery capacity. +The LTC2942 is pin compatible with the LTC2941, it adds voltage and +temperature monitoring, and is runtime detected. LTC2943 and LTC2944 +is software compatible, uses a slightly different conversion formula +for the charge counter and adds voltage, current and temperature monitoring. + +Required properties: +- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943" + or "lltc,ltc2944" which also indicates the type of I2C chip attached. +- reg: The 7-bit I2C address. +- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit + negative value when the battery has been connected to the wrong end of the + resistor. +- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet. + This determines the range and accuracy of the gauge. The value is programmed + into the chip only if it differs from the current setting. The setting is + lost when the battery is disconnected. + +Example from the Topic Miami Florida board: + + fuelgauge: ltc2943@64 { + compatible = "lltc,ltc2943"; + reg = <0x64>; + lltc,resistor-sense = <15>; + lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ + }; diff --git a/Documentation/devicetree/bindings/power/supply/max17040_battery.txt b/Documentation/devicetree/bindings/power/supply/max17040_battery.txt new file mode 100644 index 000000000..c802f664b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max17040_battery.txt @@ -0,0 +1,52 @@ +max17040_battery +~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "maxim,max17040", "maxim,max17041", "maxim,max17043", + "maxim,max17044", "maxim,max17048", "maxim,max17049", + "maxim,max17058", "maxim,max17059" or "maxim,max77836-battery" + - reg: i2c slave address + +Optional properties : +- maxim,alert-low-soc-level : The alert threshold that sets the state of + charge level (%) where an interrupt is + generated. Can be configured from 1 up to 32 + (%). If skipped the power up default value of + 4 (%) will be used. +- maxim,double-soc : Certain devices return double the capacity. + Specify this boolean property to divide the + reported value in 2 and thus normalize it. + SOC == State of Charge == Capacity. +- maxim,rcomp : A value to compensate readings for various + battery chemistries and operating temperatures. + max17040,41 have 2 byte rcomp, default to + 0x97 0x00. All other devices have one byte + rcomp, default to 0x97. +- interrupts : Interrupt line see Documentation/devicetree/ + bindings/interrupt-controller/interrupts.txt +- wakeup-source : This device has wakeup capabilities. Use this + property to use alert low SOC level interrupt + as wake up source. + +Optional properties support interrupt functionality for alert low state of +charge level, present in some ICs in the same family, and should be used with +compatible "maxim,max77836-battery". + +Example: + + battery-fuel-gauge@36 { + compatible = "maxim,max77836-battery"; + reg = <0x36>; + maxim,alert-low-soc-level = <10>; + interrupt-parent = <&gpio7>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + + battery-fuel-gauge@36 { + compatible = "maxim,max17048"; + reg = <0x36>; + maxim,rcomp = /bits/ 8 <0x56>; + maxim,alert-low-soc-level = <10>; + maxim,double-soc; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max17042_battery.txt b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt new file mode 100644 index 000000000..f34c5daae --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt @@ -0,0 +1,35 @@ +max17042_battery +~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : one of the following + * "maxim,max17042" + * "maxim,max17047" + * "maxim,max17050" + * "maxim,max17055" + +Optional properties : + - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms + (datasheet-recommended value is 10000). + Defining this property enables current-sense functionality. + +Optional threshold properties : + If skipped the condition won't be reported. + - maxim,cold-temp : Temperature threshold to report battery + as cold (in tenths of degree Celsius). + - maxim,over-heat-temp : Temperature threshold to report battery + as over heated (in tenths of degree Celsius). + - maxim,dead-volt : Voltage threshold to report battery + as dead (in mV). + - maxim,over-volt : Voltage threshold to report battery + as over voltage (in mV). + +Example: + + battery-charger@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4300>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max77650-charger.yaml b/Documentation/devicetree/bindings/power/supply/max77650-charger.yaml new file mode 100644 index 000000000..62eeddb65 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max77650-charger.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/max77650-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Battery charger driver for MAX77650 PMIC from Maxim Integrated. + +maintainers: + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + +description: | + This module is part of the MAX77650 MFD device. For more details + see Documentation/devicetree/bindings/mfd/max77650.yaml. + + The charger is represented as a sub-node of the PMIC node on the device tree. + +properties: + compatible: + const: maxim,max77650-charger + + input-voltage-min-microvolt: + description: + Minimum CHGIN regulation voltage. + enum: [ 4000000, 4100000, 4200000, 4300000, + 4400000, 4500000, 4600000, 4700000 ] + + input-current-limit-microamp: + description: + CHGIN input current limit (in microamps). + enum: [ 95000, 190000, 285000, 380000, 475000 ] + +required: + - compatible +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt new file mode 100644 index 000000000..bab947fef --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt @@ -0,0 +1,24 @@ +Maxim Semiconductor MAX8903 Battery Charger bindings + +Required properties: +- compatible: "maxim,max8903" for MAX8903 Battery Charger +- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided +- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided + +Optional properties: +- cen-gpios: Charge enable pin (active low, output) +- chg-gpios: Charger status pin (active low, input) +- flt-gpios: Fault pin (active low, output) +- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output) +- usus-gpios: USB suspend pin (active high, output) + + +Example: + + max8903-charger { + compatible = "maxim,max8903"; + dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; + cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max8925_battery.txt b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt new file mode 100644 index 000000000..d7e3e0c0f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt @@ -0,0 +1,18 @@ +max8925-battery bindings +~~~~~~~~~~~~~~~~ + +Optional properties : + - batt-detect: whether support battery detect + - topoff-threshold: set charging current in topoff mode + - fast-charge: set charging current in fast mode + - no-temp-support: whether support temperature protection detect + - no-insert-detect: whether support insert detect + +Example: + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt new file mode 100644 index 000000000..55967a0be --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt @@ -0,0 +1,26 @@ +Devicetree bindings for Maxim DS2760 +==================================== + +The ds2760 is a w1 slave device and must hence have its sub-node in DT +under a w1 bus master node. + +The device exposes a power supply, so the details described in +Documentation/devicetree/bindings/power/supply/power_supply.txt apply. + +Required properties: +- compatible: must be "maxim,ds2760" + +Optional properties: +- power-supplies: Refers to one or more power supplies connected to + this battery. +- maxim,pmod-enabled: This boolean property enables the DS2760 to enter + sleep mode when the DQ line goes low for greater + than 2 seconds and leave sleep Mode when the DQ + line goes high. +- maxim,cache-time-ms: Time im milliseconds to cache the data for. When + this time expires, the values are read again from + the hardware. Defaults to 1000. +- rated-capacity-microamp-hours: + The rated capacity of the battery, in mAh. + If not specified, the value stored in the + non-volatile chip memory is used. diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt new file mode 100644 index 000000000..f956247d4 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt @@ -0,0 +1,23 @@ +Maxim MAX14656 / AL32 USB Charger Detector + +Required properties : +- compatible : "maxim,max14656"; +- reg: i2c slave address +- interrupts: interrupt line + +Example: + +&i2c2 { + clock-frequency = <50000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + + max14656@35 { + compatible = "maxim,max14656"; + reg = <0x35>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_detect>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt new file mode 100644 index 000000000..1d284ad81 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt @@ -0,0 +1,27 @@ +Microchip UCS1002 USB Port Power Controller + +Required properties: +- compatible : Should be "microchip,ucs1002"; +- reg : I2C slave address + +Optional properties: +- interrupts : A list of interrupts lines present (could be either + corresponding to A_DET# pin, ALERT# pin, or both) +- interrupt-names : A list of interrupt names. Should contain (if + present): + - "a_det" for line connected to A_DET# pin + - "alert" for line connected to ALERT# pin + Both are expected to be IRQ_TYPE_EDGE_BOTH +Example: + +&i2c3 { + charger@32 { + compatible = "microchip,ucs1002"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ucs1002_pins>; + reg = <0x32>; + interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>, + <&gpio3 21 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "a_det", "alert"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/olpc_battery.txt b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt new file mode 100644 index 000000000..8d87d6b35 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt @@ -0,0 +1,5 @@ +OLPC battery +~~~~~~~~~~~~ + +Required properties: + - compatible : "olpc,xo1-battery" or "olpc,xo1.5-battery" diff --git a/Documentation/devicetree/bindings/power/supply/power-supply.yaml b/Documentation/devicetree/bindings/power/supply/power-supply.yaml new file mode 100644 index 000000000..c5c55f627 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/power-supply.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/power-supply.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Power Supply Core Support + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +properties: + power-supplies: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + This property is added to a supply in order to list the devices which + supply it power, referenced by their phandles. + +additionalProperties: true + +examples: + - | + power { + #address-cells = <1>; + #size-cells = <0>; + + usb_charger:charger@e { + compatible = "some,usb-charger"; + reg = <0xe>; + }; + + ac_charger:charger@c { + compatible = "some,ac-charger"; + reg = <0xc>; + }; + + battery:battery@b { + compatible = "some,battery"; + reg = <0xb>; + power-supplies = <&usb_charger>, <&ac_charger>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/power_supply.txt b/Documentation/devicetree/bindings/power/supply/power_supply.txt new file mode 100644 index 000000000..d9693e054 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/power_supply.txt @@ -0,0 +1,2 @@ +This binding has been converted to yaml please see power-supply.yaml in this +directory. diff --git a/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt new file mode 100644 index 000000000..747899223 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt @@ -0,0 +1,48 @@ +Qualcomm Coincell Charger: + +The hardware block controls charging for a coincell or capacitor that is +used to provide power backup for certain features of the power management +IC (PMIC) + +- compatible: + Usage: required + Value type: <string> + Definition: must be: "qcom,pm8941-coincell" + +- reg: + Usage: required + Value type: <u32> + Definition: base address of the coincell charger registers + +- qcom,rset-ohms: + Usage: required + Value type: <u32> + Definition: resistance (in ohms) for current-limiting resistor + must be one of: 800, 1200, 1700, 2100 + +- qcom,vset-millivolts: + Usage: required + Value type: <u32> + Definition: voltage (in millivolts) to apply for charging + must be one of: 2500, 3000, 3100, 3200 + +- qcom,charger-disable: + Usage: optional + Value type: <boolean> + Definition: defining this property disables charging + +This charger is a sub-node of one of the 8941 PMIC blocks, and is specified +as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and +../mfd/qcom-pm8xxx.txt + +Example: + + pm8941@0 { + coincell@2800 { + compatible = "qcom,pm8941-coincell"; + reg = <0x2800>; + + qcom,rset-ohms = <2100>; + qcom,vset-millivolts = <3000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt new file mode 100644 index 000000000..06f8a5ddb --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt @@ -0,0 +1,150 @@ +Qualcomm Switch-Mode Battery Charger and Boost + +PROPERTIES +- compatible: + Usage: required + Value type: <stringlist> + Description: Must be one of: + - "qcom,pm8941-charger" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Description: Base address of registers for SMBB block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Description: The format of the specifier is defined by the binding document + describing the node's interrupt parent. Must contain one + specifier for each of the following interrupts, in order: + - charge done + - charge fast mode + - charge trickle mode + - battery temperature ok + - battery present + - charger disconnected + - USB-in valid + - DC-in valid + +- interrupt-names: + Usage: required + Value type: <stringlist> + Description: Must contain the following list, strictly ordered: + "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid" + +- qcom,fast-charge-current-limit: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum charge current; May be clamped to safety limits. + +- qcom,fast-charge-low-threshold-voltage: + Usage: optional (default: 3.2V, or pre-configured value) + Value type: <u32>; uV; range [2.1V : 3.6V] + Description: Battery voltage limit above which fast charging may operate; + Below this value linear or switch-mode auto-trickle-charging + will operate. + +- qcom,fast-charge-high-threshold-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which fast charging may operate; + The fast charger will attempt to charge the battery to this + voltage. May be clamped to safety limits. + +- qcom,fast-charge-safe-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Maximum safe battery voltage; May be pre-set by bootloader, in + which case, setting this will harmlessly fail. The property + 'fast-charge-high-watermark' will be clamped by this value. + +- qcom,fast-charge-safe-current: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum safe battery charge current; May pre-set by bootloader, + in which case, setting this will harmlessly fail. The property + 'qcom,fast-charge-current-limit' will be clamped by this value. + +- qcom,auto-recharge-threshold-voltage: + Usage: optional (default: 4.1V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which auto-recharge functionality + will restart charging after end-of-charge; The high cutoff + limit for auto-recharge is 5% above this value. + +- qcom,minimum-input-voltage: + Usage: optional (default: 4.3V, or pre-configured value) + Value type: <u32>; uV; range [4.2V : 9.6V] + Description: Input voltage level above which charging may operate + +- qcom,dc-current-limit: + Usage: optional (default: 100mA, or pre-configured value) + Value type: <u32>; uA; range [100mA : 2.5A] + Description: Default DC charge current limit + +- qcom,disable-dc: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Disable DC charger + +- qcom,jeita-extended-temp-range: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Enable JEITA extended temperature range; This does *not* + adjust the maximum charge voltage or current in the extended + temperature range. It only allows charging when the battery + is in the extended temperature range. Voltage/current + regulation must be done externally to fully comply with + the JEITA safety guidelines if this flag is set. + +- usb_otg_in-supply: + Usage: optional + Value type: <phandle> + Description: Reference to the regulator supplying power to the USB_OTG_IN + pin. + +child nodes: +- otg-vbus: + Usage: optional + Description: This node defines a regulator used to control the direction + of VBUS voltage - specifically: whether to supply voltage + to VBUS for host mode operation of the OTG port, or allow + input voltage from external VBUS for charging. In the + hardware, the supply for this regulator comes from + usb_otg_in-supply. + +EXAMPLE +charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000 0x700>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + + qcom,fast-charge-current-limit = <1000000>; + qcom,dc-charge-current-limit = <1000000>; + usb_otg_in-supply = <&pm8941_5vs1>; + + otg-vbus {}; +}; diff --git a/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml b/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml new file mode 100644 index 000000000..9852d2feb --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml @@ -0,0 +1,163 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/rohm,bd99954.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD99954 Battery charger + +maintainers: + - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> + - Markus Laine <markus.laine@fi.rohmeurope.com> + - Mikko Mutanen <mikko.mutanen@fi.rohmeurope.com> + +description: | + The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion + secondary battery intended to be used in space-constraint equipment such + as Low profile Notebook PC, Tablets and other applications. BD99954 + provides a Dual-source Battery Charger, two port BC1.2 detection and a + Battery Monitor. + + +properties: + compatible: + const: rohm,bd99954 +# +# The battery charging profile of BD99954. +# +# Curve (1) represents charging current. +# Curve (2) represents battery voltage. +# +# The BD99954 data sheet divides charging to three phases. +# a) Trickle-charge with constant current (8). +# b) pre-charge with constant current (6) +# c) fast-charge with: +# First a constant current (5) phase (CC) +# Then constant voltage (CV) phase (after the battery voltage has reached +# target level - until charging current has dropped to termination +# level (7) +# +# V ^ ^ I +# . . +# . . +# (4)- -.- - - - - - - - - - - - - - +++++++++++++++++++++++++++. +# . / . +# . ++++++/++ - - - - - - - - - - - - -.- - (5) +# . + / + . +# . + - -- . +# . + - + . +# . +.- -: . +# . .+ +` . +# . .- + | `/ . +# . .." + .: . +# . -" + -- . +# . (2) ..." + | :- . +# . ..."" + -: . +# (3)- -.-.""- - - - -+++++++++ - - - - - - -.:- - - - - - - - - .- - (6) +# . + `:. . +# . + | -: . +# . + -: . +# . + .. . +# . (1) + | "+++- - - -.- - (7) +# -++++++++++++++- - - - - - - - - - - - - - - - - + - - - .- - (8) +# . + - +# -------------------------------------------------+++++++++--> +# | | | CC | CV | +# | --trickle-- | -pre- | ---------fast----------- | +# +# The charger uses the following battery properties +# - trickle-charge-current-microamp: +# Current used at trickle-charge phase (8 in above chart) +# minimum: 64000 +# maximum: 1024000 +# multipleOf: 64000 +# - precharge-current-microamp: +# Current used at pre-charge phase (6 in above chart) +# minimum: 64000 +# maximum: 1024000 +# multipleOf: 64000 +# - constant-charge-current-max-microamp +# Current used at fast charge constant current phase (5 in above chart) +# minimum: 64000 +# maximum: 1024000 +# multipleOf: 64000 +# - constant-charge-voltage-max-microvolt +# The constant voltage used in fast charging phase (4 in above chart) +# minimum: 2560000 +# maximum: 19200000 +# multipleOf: 16000 +# - precharge-upper-limit-microvolt +# charging mode is changed from trickle charging to pre-charging +# when battery voltage exceeds this limit voltage (3 in above chart) +# minimum: 2048000 +# maximum: 19200000 +# multipleOf: 64000 +# - re-charge-voltage-microvolt +# minimum: 2560000 +# maximum: 19200000 +# multipleOf: 16000 +# re-charging is automatically started when battry has been discharging +# to the point where the battery voltage drops below this limit +# - over-voltage-threshold-microvolt +# battery is expected to be faulty if battery voltage exceeds this limit. +# Charger will then enter to a "battery faulty" -state +# minimum: 2560000 +# maximum: 19200000 +# multipleOf: 16000 +# - charge-term-current-microamp +# minimum: 0 +# maximum: 1024000 +# multipleOf: 64000 +# a charge cycle terminates when the battery voltage is above recharge +# threshold, and the current is below this setting (7 in above chart) +# See also Documentation/devicetree/bindings/power/supply/battery.txt + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + monitored-battery: + description: + phandle of battery characteristics devicetree node + + rohm,vsys-regulation-microvolt: + description: system specific lower limit for system voltage. + minimum: 2560000 + maximum: 19200000 + multipleOf: 64000 + + rohm,vbus-input-current-limit-microamp: + description: system specific VBUS input current limit (in microamps). + minimum: 32000 + maximum: 16352000 + multipleOf: 32000 + + rohm,vcc-input-current-limit-microamp: + description: system specific VCC/VACP input current limit (in microamps). + minimum: 32000 + maximum: 16352000 + multipleOf: 32000 + +required: + - compatible + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + charger@9 { + compatible = "rohm,bd99954"; + monitored-battery = <&battery>; + reg = <0x9>; + interrupt-parent = <&gpio1>; + interrupts = <29 8>; + rohm,vsys-regulation-microvolt = <8960000>; + rohm,vbus-input-current-limit-microamp = <1472000>; + rohm,vcc-input-current-limit-microamp = <1472000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt new file mode 100644 index 000000000..1e6107c75 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt @@ -0,0 +1,46 @@ +Binding for Richtek rt9455 battery charger + +Required properties: +- compatible: it should contain one of the following: + "richtek,rt9455". +- reg: integer, i2c address of the device. +- interrupts: interrupt mapping for GPIO IRQ, it should be + configured with IRQ_TYPE_LEVEL_LOW flag. +- richtek,output-charge-current: integer, output current from the charger to the + battery, in uA. +- richtek,end-of-charge-percentage: integer, percent of the output charge current. + When the current in constant-voltage phase drops + below output_charge_current x end-of-charge-percentage, + charge is terminated. +- richtek,battery-regulation-voltage: integer, maximum battery voltage in uV. +- richtek,boost-output-voltage: integer, maximum voltage provided to consumer + devices, when the charger is in boost mode, in uV. + +Optional properties: +- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to + decrease voltage level when the over current + of the input power source occurs. + This prevents input voltage drop due to insufficient + current provided by the power source. + Default: 4500000 uV (4.5V) +- richtek,avg-input-current-regulation: integer, input current value in uA drained by the + charger from the power source. + Default: 500000 uA (500mA) + +Example: + +rt9455@22 { + compatible = "richtek,rt9455"; + reg = <0x22>; + + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + richtek,output-charge-current = <500000>; + richtek,end-of-charge-percentage = <10>; + richtek,battery-regulation-voltage = <4200000>; + richtek,boost-output-voltage = <5050000>; + + richtek,min-input-voltage-regulation = <4500000>; + richtek,avg-input-current-regulation = <500000>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/rx51-battery.txt b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt new file mode 100644 index 000000000..90438453d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt @@ -0,0 +1,25 @@ +Binding for Nokia N900 battery + +The Nokia N900 battery status can be read via the TWL4030's A/D converter. + +Required properties: +- compatible: Should contain one of the following: + * "nokia,n900-battery" +- io-channels: Should contain IIO channel specifiers + for each element in io-channel-names. +- io-channel-names: Should contain the following values: + * "temp" - The ADC channel for temperature reading + * "bsi" - The ADC channel for battery size identification + * "vbat" - The ADC channel to measure the battery voltage + +Example from Nokia N900: + +battery: n900-battery { + compatible = "nokia,n900-battery"; + io-channels = <&twl4030_madc 0>, + <&twl4030_madc 4>, + <&twl4030_madc 12>; + io-channel-names = "temp", + "bsi", + "vbat"; +}; diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml b/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml new file mode 100644 index 000000000..a90b3601e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/sbs,sbs-battery.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SBS compliant battery + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: | + Battery compatible with the smart battery system specifications + +properties: + + compatible: + oneOf: + - items: + - enum: + - ti,bq20z65 + - ti,bq20z75 + - enum: + - sbs,sbs-battery + - items: + - const: sbs,sbs-battery + + reg: + maxItems: 1 + + sbs,i2c-retry-count: + description: + The number of times to retry I2C transactions on I2C IO failure. + default: 0 + $ref: /schemas/types.yaml#/definitions/uint32 + + sbs,poll-retry-count: + description: + The number of times to try looking for new status after an external + change notification. + default: 0 + $ref: /schemas/types.yaml#/definitions/uint32 + + sbs,battery-detect-gpios: + description: + GPIO which signals battery detection. If this is not supplied, the bus + needs to be polled to detect the battery. + maxItems: 1 + + sbs,disable-charger-broadcasts: + description: + SBS batteries by default send broadcast messages to SBS compliant chargers to + configure max. charge current/voltage. If your hardware does not have an SBS + compliant charger it should be disabled via this property to avoid blocking + the bus. Also some SBS battery fuel gauges are known to have a buggy multi- + master implementation. + type: boolean + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + battery@b { + compatible = "ti,bq20z75", "sbs,sbs-battery"; + reg = <0xb>; + sbs,i2c-retry-count = <2>; + sbs,poll-retry-count = <10>; + sbs,battery-detect-gpios = <&gpio 122 GPIO_ACTIVE_HIGH>; + sbs,disable-charger-broadcasts; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt new file mode 100644 index 000000000..4b2195571 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt @@ -0,0 +1,66 @@ +Binding for sbs-manager + +Required properties: +- compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. +- reg: integer, i2c address of the device. Should be <0xa>. +Optional properties: +- gpio-controller: Marks the port as GPIO controller. + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- #gpio-cells: Should be <2>. The first cell is the pin number, the second cell + is used to specify optional parameters: + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. + +From OS view the device is basically an i2c-mux used to communicate with up to +four smart battery devices at address 0xb. The driver actually implements this +behaviour. So standard i2c-mux nodes can be used to register up to four slave +batteries. Channels will be numerated starting from 1 to 4. + +Example: + +batman@a { + compatible = "lltc,ltc1760", "sbs,sbs-manager"; + reg = <0x0a>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + battery@b { + compatible = "ti,bq2060", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 1 1>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + battery@b { + compatible = "ti,bq2060", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 2 1>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + battery@b { + compatible = "ti,bq2060", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 3 1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt new file mode 100644 index 000000000..84e74151e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt @@ -0,0 +1,21 @@ +SBS sbs-charger +~~~~~~~~~~ + +Required properties: + - compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. + +Optional properties: +- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with + "interrupt-parent". If an interrupt is not provided the driver will switch + automatically to polling. + +Example: + + ltc4100@9 { + compatible = "lltc,ltc4100", "sbs,sbs-charger"; + reg = <0x9>; + interrupt-parent = <&gpio6>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt new file mode 100644 index 000000000..5266fab16 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt @@ -0,0 +1,40 @@ +Spreadtrum SC2731 PMIC battery charger binding + +Required properties: + - compatible: Should be "sprd,sc2731-charger". + - reg: Address offset of charger register. + - phys: Contains a phandle to the USB phy. + +Optional Properties: +- monitored-battery: phandle of battery characteristics devicetree node. + The charger uses the following battery properties: +- charge-term-current-microamp: current for charge termination phase. +- constant-charge-voltage-max-microvolt: maximum constant input voltage. + See Documentation/devicetree/bindings/power/supply/battery.txt + +Example: + + bat: battery { + compatible = "simple-battery"; + charge-term-current-microamp = <120000>; + constant-charge-voltage-max-microvolt = <4350000>; + ...... + }; + + sc2731_pmic: pmic@0 { + compatible = "sprd,sc2731"; + reg = <0>; + spi-max-frequency = <26000000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + + charger@0 { + compatible = "sprd,sc2731-charger"; + reg = <0x0>; + phys = <&ssphy>; + monitored-battery = <&bat>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt new file mode 100644 index 000000000..b6359b590 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt @@ -0,0 +1,59 @@ +Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings + +Required properties: +- compatible: Should be one of the following: + "sprd,sc2720-fgu", + "sprd,sc2721-fgu", + "sprd,sc2723-fgu", + "sprd,sc2730-fgu", + "sprd,sc2731-fgu". +- reg: The address offset of fuel gauge unit. +- battery-detect-gpios: GPIO for battery detection. +- io-channels: Specify the IIO ADC channels to get temperature and charge voltage. +- io-channel-names: Should be "bat-temp" or "charge-vol". +- nvmem-cells: A phandle to the calibration cells provided by eFuse device. +- nvmem-cell-names: Should be "fgu_calib". +- sprd,calib-resistance-micro-ohms: Specify the real resistance of coulomb counter + chip in micro Ohms. +- monitored-battery: Phandle of battery characteristics devicetree node. + See Documentation/devicetree/bindings/power/supply/battery.txt + +Example: + + bat: battery { + compatible = "simple-battery"; + charge-full-design-microamp-hours = <1900000>; + constant-charge-voltage-max-microvolt = <4350000>; + ocv-capacity-celsius = <20>; + ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, + <4022000 85>, <3983000 80>, <3949000 75>, + <3917000 70>, <3889000 65>, <3864000 60>, + <3835000 55>, <3805000 50>, <3787000 45>, + <3777000 40>, <3773000 35>, <3770000 30>, + <3765000 25>, <3752000 20>, <3724000 15>, + <3680000 10>, <3605000 5>, <3400000 0>; + ...... + }; + + sc2731_pmic: pmic@0 { + compatible = "sprd,sc2731"; + reg = <0>; + spi-max-frequency = <26000000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + + fgu@a00 { + compatible = "sprd,sc2731-fgu"; + reg = <0xa00>; + battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>; + io-channels = <&pmic_adc 5>, <&pmic_adc 14>; + io-channel-names = "bat-temp", "charge-vol"; + nvmem-cells = <&fgu_calib>; + nvmem-cell-names = "fgu_calib"; + monitored-battery = <&bat>; + sprd,calib-resistance-micro-ohms = <21500>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml b/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml new file mode 100644 index 000000000..983fc215c --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml @@ -0,0 +1,152 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/summit,smb347-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Battery charger driver for SMB345, SMB347 and SMB358 + +maintainers: + - David Heidelberg <david@ixit.cz> + - Dmitry Osipenko <digetx@gmail.com> + +properties: + compatible: + enum: + - summit,smb345 + - summit,smb347 + - summit,smb358 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + monitored-battery: + description: phandle to the battery node + $ref: /schemas/types.yaml#/definitions/phandle + + summit,enable-usb-charging: + type: boolean + description: Enable charging through USB. + + summit,enable-otg-charging: + type: boolean + description: Provide power for USB OTG + + summit,enable-mains-charging: + type: boolean + description: Enable charging through mains + + summit,enable-charge-control: + description: Enable charging control + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # SMB3XX_CHG_ENABLE_SW SW (I2C interface) + - 1 # SMB3XX_CHG_ENABLE_PIN_ACTIVE_LOW Pin control (Active Low) + - 2 # SMB3XX_CHG_ENABLE_PIN_ACTIVE_HIGH Pin control (Active High) + + summit,fast-voltage-threshold-microvolt: + description: Voltage threshold to transit to fast charge mode (in uV) + minimum: 2400000 + maximum: 3000000 + + summit,mains-current-limit-microamp: + description: Maximum input current from AC/DC input (in uA) + + summit,usb-current-limit-microamp: + description: Maximum input current from USB input (in uA) + + summit,charge-current-compensation-microamp: + description: Charge current compensation (in uA) + + summit,chip-temperature-threshold-celsius: + description: Chip temperature for thermal regulation in °C. + enum: [100, 110, 120, 130] + + summit,soft-compensation-method: + description: Soft temperature limit compensation method + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # SMB3XX_SOFT_TEMP_COMPENSATE_NONE Compensation none + - 1 # SMB3XX_SOFT_TEMP_COMPENSATE_CURRENT Current compensation + - 2 # SMB3XX_SOFT_TEMP_COMPENSATE_VOLTAGE Voltage compensation + +allOf: + - if: + properties: + compatible: + enum: + - summit,smb345 + - summit,smb358 + + then: + properties: + summit,mains-current-limit-microamp: + enum: [ 300000, 500000, 700000, 1000000, + 1500000, 1800000, 2000000] + + summit,usb-current-limit-microamp: + enum: [ 300000, 500000, 700000, 1000000, + 1500000, 1800000, 2000000] + + summit,charge-current-compensation-microamp: + enum: [200000, 450000, 600000, 900000] + + else: + properties: + summit,mains-current-limit-microamp: + enum: [ 300000, 500000, 700000, 900000, 1200000, + 1500000, 1800000, 2000000, 2200000, 2500000] + + summit,usb-current-limit-microamp: + enum: [ 300000, 500000, 700000, 900000, 1200000, + 1500000, 1800000, 2000000, 2200000, 2500000] + + summit,charge-current-compensation-microamp: + enum: [250000, 700000, 900000, 1200000] + +required: + - compatible + - reg + +anyOf: + - required: + - summit,enable-usb-charging + - required: + - summit,enable-otg-charging + - required: + - summit,enable-mains-charging + +additionalProperties: false + +examples: + - | + #include <dt-bindings/power/summit,smb347-charger.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@7f { + compatible = "summit,smb347"; + reg = <0x7f>; + + summit,enable-charge-control = <SMB3XX_CHG_ENABLE_PIN_ACTIVE_HIGH>; + summit,chip-temperature-threshold-celsius = <110>; + summit,mains-current-limit-microamp = <2000000>; + summit,usb-current-limit-microamp = <500000>; + summit,enable-usb-charging; + summit,enable-mains-charging; + + monitored-battery = <&battery>; + }; + }; + + battery: battery-cell { + compatible = "simple-battery"; + constant-charge-current-max-microamp = <1800000>; + operating-range-celsius = <0 45>; + alert-celsius = <3 42>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt new file mode 100644 index 000000000..de45e1a2a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt @@ -0,0 +1,39 @@ +TI BQ24735 Charge Controller +~~~~~~~~~~ + +Required properties : + - compatible : "ti,bq24735" + +Optional properties : + - interrupts : Specify the interrupt to be used to trigger when the AC + adapter is either plugged in or removed. + - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter + status. This is a Host GPIO that is configured as an input and connected + to the ACOK pin on the bq24735. Note: for backwards compatibility reasons, + the GPIO must be active on AC adapter absence despite ACOK being active + (high) on AC adapter presence. + - ti,charge-current : Used to control and set the charging current. This value + must be between 128mA and 8.128A with a 64mA step resolution. The POR value + is 0x0000h. This number is in mA (e.g. 8192), see spec for more information + about the ChargeCurrent (0x14h) register. + - ti,charge-voltage : Used to control and set the charging voltage. This value + must be between 1.024V and 19.2V with a 16mV step resolution. The POR value + is 0x0000h. This number is in mV (e.g. 19200), see spec for more information + about the ChargeVoltage (0x15h) register. + - ti,input-current : Used to control and set the charger input current. This + value must be between 128mA and 8.064A with a 128mA step resolution. The + POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for + more information about the InputCurrent (0x3fh) register. + - ti,external-control : Indicates that the charger is configured externally + and that the host should not attempt to enable/disable charging or set the + charge voltage/current. + - poll-interval : In case 'interrupts' is not specified, poll AC adapter + presence with this interval (milliseconds). + +Example: + + bq24735@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + ti,ac-detect-gpios = <&gpio 72 0x1>; + } diff --git a/Documentation/devicetree/bindings/power/supply/tps65090.txt b/Documentation/devicetree/bindings/power/supply/tps65090.txt new file mode 100644 index 000000000..8e5e0d391 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65090.txt @@ -0,0 +1,17 @@ +TPS65090 Frontend PMU with Switchmode Charger + +Required Properties: +-compatible: "ti,tps65090-charger" + +Optional Properties: +-ti,enable-low-current-chrg: Enables charging when a low current is detected + while the default logic is to stop charging. + +This node is a subnode of the tps65090 PMIC. + +Example: + + tps65090-charger { + compatible = "ti,tps65090-charger"; + ti,enable-low-current-chrg; + }; diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt new file mode 100644 index 000000000..a11072c5a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt @@ -0,0 +1,17 @@ +TPS65217 Charger + +Required Properties: +-compatible: "ti,tps65217-charger" +-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change. + Should be <0> for the USB charger and <1> for the AC adapter. +-interrupt-names: Should be "USB" and "AC" + +This node is a subnode of the tps65217 PMIC. + +Example: + + tps65217-charger { + compatible = "ti,tps65217-charger"; + interrupts = <0>, <1>; + interrupt-names = "USB", "AC"; + }; diff --git a/Documentation/devicetree/bindings/power/supply/twl-charger.txt b/Documentation/devicetree/bindings/power/supply/twl-charger.txt new file mode 100644 index 000000000..3b4ea1b73 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/twl-charger.txt @@ -0,0 +1,30 @@ +TWL BCI (Battery Charger Interface) + +The battery charger needs to interact with the USB phy in order +to know when charging is permissible, and when there is a connection +or disconnection. + +The choice of phy cannot be configured at a hardware level, so there +is no value in explicit configuration in device-tree. Rather +if there is a sibling of the BCI node which is compatible with +"ti,twl4030-usb", then that is used to determine when and how +use USB power for charging. + +Required properties: +- compatible: + - "ti,twl4030-bci" +- interrupts: two interrupt lines from the TWL SIH (secondary + interrupt handler) - interrupts 9 and 2. + +Optional properties: +- ti,bb-uvolt: microvolts for charging the backup battery. +- ti,bb-uamp: microamps for charging the backup battery. + +Examples: + +bci { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; |