diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt | 85 |
1 files changed, 85 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt new file mode 100644 index 000000000..c483dcec0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -0,0 +1,85 @@ +Texas Instruments McASP controller + +Required properties: +- compatible : + "ti,dm646x-mcasp-audio" : for DM646x platforms + "ti,da830-mcasp-audio" : for both DA830 & DA850 platforms + "ti,am33xx-mcasp-audio" : for AM33xx platforms (AM33xx, AM43xx, TI81xx) + "ti,dra7-mcasp-audio" : for DRA7xx platforms + +- reg : Should contain reg specifiers for the entries in the reg-names property. +- reg-names : Should contain: + * "mpu" for the main registers (required). For compatibility with + existing software, it is recommended this is the first entry. + * "dat" for separate data port register access (optional). +- op-mode : I2S/DIT ops mode. 0 for I2S mode. 1 for DIT mode used for S/PDIF, + IEC60958-1, and AES-3 formats. +- tdm-slots : Slots for TDM operation. Indicates number of channels transmitted + or received over one serializer. +- serial-dir : A list of serializer configuration. Each entry is a number + indication for serializer pin direction. + (0 - INACTIVE, 1 - TX, 2 - RX) +- dmas: two element list of DMA controller phandles and DMA request line + ordered pairs. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". + +Optional properties: + +- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0 +- tx-num-evt : FIFO levels. +- rx-num-evt : FIFO levels. +- dismod : Specify the drive on TX pin during inactive slots + 0 : 3-state + 2 : logic low + 3 : logic high + Defaults to 'logic low' when the property is not present +- sram-size-playback : size of sram to be allocated during playback +- sram-size-capture : size of sram to be allocated during capture +- interrupts : Interrupt numbers for McASP +- interrupt-names : Known interrupt names are "tx" and "rx" +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt +- fck_parent : Should contain a valid clock name which will be used as parent + for the McASP fck +- auxclk-fs-ratio: When McASP is bus master indicates the ratio between AUCLK + and FS rate if applicable: + AUCLK rate = auxclk-fs-ratio * FS rate + +Optional GPIO support: +If any McASP pin need to be used as GPIO then the McASP node must have: +... + gpio-controller + #gpio-cells = <2>; +... + +When requesting a GPIO, the first parameter is the PIN index in McASP_P* +registers. +For example to request the AXR2 pin of mcasp8: +function-gpios = <&mcasp8 2 0>; + +Or to request the ACLKR pin of mcasp8: +function-gpios = <&mcasp8 29 0>; + +For generic gpio information, please refer to bindings/gpio/gpio.txt + +Example: + +mcasp0: mcasp0@1d00000 { + compatible = "ti,da830-mcasp-audio"; + reg = <0x100000 0x3000>; + reg-names "mpu"; + interrupts = <82>, <83>; + interrupt-names = "tx", "rx"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < + 0 0 0 0 /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 0 0 + 0 0 0 1 + 2 0 0 0 >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; |