diff options
Diffstat (limited to 'arch/arm/boot/dts/stm32mp157c-ev1.dts')
| -rw-r--r-- | arch/arm/boot/dts/stm32mp157c-ev1.dts | 376 |
1 files changed, 376 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts new file mode 100644 index 000000000..a55e80ce2 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts @@ -0,0 +1,376 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) STMicroelectronics 2017 - All Rights Reserved + * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. + */ +/dts-v1/; + +#include "stm32mp157c-ed1.dts" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "STMicroelectronics STM32MP157C eval daughter on eval mother"; + compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + serial0 = &uart4; + serial1 = &usart3; + ethernet0 = ðernet0; + }; + + clocks { + clk_ext_camera: clk-ext-camera { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + }; + + joystick { + compatible = "gpio-keys"; + pinctrl-0 = <&joystick_pins>; + pinctrl-names = "default"; + button-0 { + label = "JoySel"; + linux,code = <KEY_ENTER>; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + }; + button-1 { + label = "JoyDown"; + linux,code = <KEY_DOWN>; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <1 IRQ_TYPE_EDGE_RISING>; + }; + button-2 { + label = "JoyLeft"; + linux,code = <KEY_LEFT>; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + }; + button-3 { + label = "JoyRight"; + linux,code = <KEY_RIGHT>; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + }; + button-4 { + label = "JoyUp"; + linux,code = <KEY_UP>; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <4 IRQ_TYPE_EDGE_RISING>; + }; + }; + + panel_backlight: panel-backlight { + compatible = "gpio-backlight"; + gpios = <&gpiod 13 GPIO_ACTIVE_LOW>; + default-on; + status = "okay"; + }; +}; + +&cec { + pinctrl-names = "default"; + pinctrl-0 = <&cec_pins_a>; + status = "okay"; +}; + +&dcmi { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcmi_pins_a>; + pinctrl-1 = <&dcmi_sleep_pins_a>; + + port { + dcmi_0: endpoint { + remote-endpoint = <&ov5640_0>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; +}; + +&dsi { + phy-dsi-supply = <®18>; + status = "okay"; + + ports { + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <<dc_ep0_out>; + }; + }; + + port@1 { + reg = <1>; + dsi_out: endpoint { + remote-endpoint = <&dsi_panel_in>; + }; + }; + }; + + panel-dsi@0 { + compatible = "raydium,rm68200"; + reg = <0>; + reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>; + backlight = <&panel_backlight>; + power-supply = <&v3v3>; + status = "okay"; + + port { + dsi_panel_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; +}; + +&fmc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&fmc_pins_a>; + pinctrl-1 = <&fmc_sleep_pins_a>; + status = "okay"; + + nand-controller@4,0 { + status = "okay"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_pins_a>; + pinctrl-1 = <&i2c2_sleep_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + + ov5640: camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + DOVDD-supply = <&v2v8>; + powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>; + reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + rotation = <180>; + status = "okay"; + + port { + ov5640_0: endpoint { + remote-endpoint = <&dcmi_0>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; + + stmfx: stmfx@42 { + compatible = "st,stmfx-0300"; + reg = <0x42>; + interrupts = <8 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpioi>; + vdd-supply = <&v3v3>; + + stmfx_pinctrl: pinctrl { + compatible = "st,stmfx-0300-pinctrl"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&stmfx_pinctrl 0 0 24>; + + joystick_pins: joystick-pins { + pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4"; + bias-pull-down; + }; + }; + }; +}; + +&i2c5 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c5_pins_a>; + pinctrl-1 = <&i2c5_sleep_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + +<dc { + status = "okay"; + + port { + ltdc_ep0_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&dsi_in>; + }; + }; +}; + +&m_can1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can1_pins_a>; + pinctrl-1 = <&m_can1_sleep_pins_a>; + status = "okay"; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: mx66l51235l@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + flash1: mx66l51235l@1 { + compatible = "jedec,spi-nor"; + reg = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&sdmmc3 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc3_b4_pins_a>; + pinctrl-1 = <&sdmmc3_b4_od_pins_a>; + pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>; + broken-cd; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + status = "disabled"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + status = "disabled"; +}; + +&timers2 { + /* spare dmas for other usage (un-delete to enable pwm capture) */ + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; + pwm { + pinctrl-0 = <&pwm2_pins_a>; + pinctrl-1 = <&pwm2_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@1 { + status = "okay"; + }; +}; + +&timers8 { + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; + pwm { + pinctrl-0 = <&pwm8_pins_a>; + pinctrl-1 = <&pwm8_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@7 { + status = "okay"; + }; +}; + +&timers12 { + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; + pwm { + pinctrl-0 = <&pwm12_pins_a>; + pinctrl-1 = <&pwm12_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@11 { + status = "okay"; + }; +}; + +&usart3 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&usart3_pins_b>; + pinctrl-1 = <&usart3_sleep_pins_b>; + pinctrl-2 = <&usart3_idle_pins_b>; + /* + * HW flow control USART3_RTS is optional, and isn't default wired to + * the connector. SB23 needs to be soldered in order to use it, and R77 + * (ETH_CLK) should be removed. + */ + uart-has-rtscts; + status = "disabled"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbotg_hs { + pinctrl-0 = <&usbotg_hs_pins_a>; + pinctrl-names = "default"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; |