diff options
Diffstat (limited to 'drivers/mtd/nand/raw/fsl_elbc_nand.c')
| -rw-r--r-- | drivers/mtd/nand/raw/fsl_elbc_nand.c | 1003 |
1 files changed, 1003 insertions, 0 deletions
diff --git a/drivers/mtd/nand/raw/fsl_elbc_nand.c b/drivers/mtd/nand/raw/fsl_elbc_nand.c new file mode 100644 index 000000000..c174b6dc3 --- /dev/null +++ b/drivers/mtd/nand/raw/fsl_elbc_nand.c @@ -0,0 +1,1003 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* Freescale Enhanced Local Bus Controller NAND driver + * + * Copyright © 2006-2007, 2010 Freescale Semiconductor + * + * Authors: Nick Spence <nick.spence@freescale.com>, + * Scott Wood <scottwood@freescale.com> + * Jack Lan <jack.lan@freescale.com> + * Roy Zang <tie-fei.zang@freescale.com> + */ + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/ioport.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/interrupt.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/rawnand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <asm/io.h> +#include <asm/fsl_lbc.h> + +#define MAX_BANKS 8 +#define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */ +#define FCM_TIMEOUT_MSECS 500 /* Maximum number of mSecs to wait for FCM */ + +/* mtd information per set */ + +struct fsl_elbc_mtd { + struct nand_chip chip; + struct fsl_lbc_ctrl *ctrl; + + struct device *dev; + int bank; /* Chip select bank number */ + u8 __iomem *vbase; /* Chip select base virtual address */ + int page_size; /* NAND page size (0=512, 1=2048) */ + unsigned int fmr; /* FCM Flash Mode Register value */ +}; + +/* Freescale eLBC FCM controller information */ + +struct fsl_elbc_fcm_ctrl { + struct nand_controller controller; + struct fsl_elbc_mtd *chips[MAX_BANKS]; + + u8 __iomem *addr; /* Address of assigned FCM buffer */ + unsigned int page; /* Last page written to / read from */ + unsigned int read_bytes; /* Number of bytes read during command */ + unsigned int column; /* Saved column from SEQIN */ + unsigned int index; /* Pointer to next byte to 'read' */ + unsigned int status; /* status read from LTESR after last op */ + unsigned int mdr; /* UPM/FCM Data Register value */ + unsigned int use_mdr; /* Non zero if the MDR is to be set */ + unsigned int oob; /* Non zero if operating on OOB data */ + unsigned int counter; /* counter for the initializations */ + unsigned int max_bitflips; /* Saved during READ0 cmd */ +}; + +/* These map to the positions used by the FCM hardware ECC generator */ + +static int fsl_elbc_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + + if (section >= chip->ecc.steps) + return -ERANGE; + + oobregion->offset = (16 * section) + 6; + if (priv->fmr & FMR_ECCM) + oobregion->offset += 2; + + oobregion->length = chip->ecc.bytes; + + return 0; +} + +static int fsl_elbc_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + + if (section > chip->ecc.steps) + return -ERANGE; + + if (!section) { + oobregion->offset = 0; + if (mtd->writesize > 512) + oobregion->offset++; + oobregion->length = (priv->fmr & FMR_ECCM) ? 7 : 5; + } else { + oobregion->offset = (16 * section) - + ((priv->fmr & FMR_ECCM) ? 5 : 7); + if (section < chip->ecc.steps) + oobregion->length = 13; + else + oobregion->length = mtd->oobsize - oobregion->offset; + } + + return 0; +} + +static const struct mtd_ooblayout_ops fsl_elbc_ooblayout_ops = { + .ecc = fsl_elbc_ooblayout_ecc, + .free = fsl_elbc_ooblayout_free, +}; + +/* + * ELBC may use HW ECC, so that OOB offsets, that NAND core uses for bbt, + * interfere with ECC positions, that's why we implement our own descriptors. + * OOB {11, 5}, works for both SP and LP chips, with ECCM = 1 and ECCM = 0. + */ +static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; +static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +/*=================================*/ + +/* + * Set up the FCM hardware block and page address fields, and the fcm + * structure addr field to point to the correct FCM buffer in memory + */ +static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + int buf_num; + + elbc_fcm_ctrl->page = page_addr; + + if (priv->page_size) { + /* + * large page size chip : FPAR[PI] save the lowest 6 bits, + * FBAR[BLK] save the other bits. + */ + out_be32(&lbc->fbar, page_addr >> 6); + out_be32(&lbc->fpar, + ((page_addr << FPAR_LP_PI_SHIFT) & FPAR_LP_PI) | + (oob ? FPAR_LP_MS : 0) | column); + buf_num = (page_addr & 1) << 2; + } else { + /* + * small page size chip : FPAR[PI] save the lowest 5 bits, + * FBAR[BLK] save the other bits. + */ + out_be32(&lbc->fbar, page_addr >> 5); + out_be32(&lbc->fpar, + ((page_addr << FPAR_SP_PI_SHIFT) & FPAR_SP_PI) | + (oob ? FPAR_SP_MS : 0) | column); + buf_num = page_addr & 7; + } + + elbc_fcm_ctrl->addr = priv->vbase + buf_num * 1024; + elbc_fcm_ctrl->index = column; + + /* for OOB data point to the second half of the buffer */ + if (oob) + elbc_fcm_ctrl->index += priv->page_size ? 2048 : 512; + + dev_vdbg(priv->dev, "set_addr: bank=%d, " + "elbc_fcm_ctrl->addr=0x%p (0x%p), " + "index %x, pes %d ps %d\n", + buf_num, elbc_fcm_ctrl->addr, priv->vbase, + elbc_fcm_ctrl->index, + chip->phys_erase_shift, chip->page_shift); +} + +/* + * execute FCM command and wait for it to complete + */ +static int fsl_elbc_run_command(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + + /* Setup the FMR[OP] to execute without write protection */ + out_be32(&lbc->fmr, priv->fmr | 3); + if (elbc_fcm_ctrl->use_mdr) + out_be32(&lbc->mdr, elbc_fcm_ctrl->mdr); + + dev_vdbg(priv->dev, + "fsl_elbc_run_command: fmr=%08x fir=%08x fcr=%08x\n", + in_be32(&lbc->fmr), in_be32(&lbc->fir), in_be32(&lbc->fcr)); + dev_vdbg(priv->dev, + "fsl_elbc_run_command: fbar=%08x fpar=%08x " + "fbcr=%08x bank=%d\n", + in_be32(&lbc->fbar), in_be32(&lbc->fpar), + in_be32(&lbc->fbcr), priv->bank); + + ctrl->irq_status = 0; + /* execute special operation */ + out_be32(&lbc->lsor, priv->bank); + + /* wait for FCM complete flag or timeout */ + wait_event_timeout(ctrl->irq_wait, ctrl->irq_status, + FCM_TIMEOUT_MSECS * HZ/1000); + elbc_fcm_ctrl->status = ctrl->irq_status; + /* store mdr value in case it was needed */ + if (elbc_fcm_ctrl->use_mdr) + elbc_fcm_ctrl->mdr = in_be32(&lbc->mdr); + + elbc_fcm_ctrl->use_mdr = 0; + + if (elbc_fcm_ctrl->status != LTESR_CC) { + dev_info(priv->dev, + "command failed: fir %x fcr %x status %x mdr %x\n", + in_be32(&lbc->fir), in_be32(&lbc->fcr), + elbc_fcm_ctrl->status, elbc_fcm_ctrl->mdr); + return -EIO; + } + + if (chip->ecc.engine_type != NAND_ECC_ENGINE_TYPE_ON_HOST) + return 0; + + elbc_fcm_ctrl->max_bitflips = 0; + + if (elbc_fcm_ctrl->read_bytes == mtd->writesize + mtd->oobsize) { + uint32_t lteccr = in_be32(&lbc->lteccr); + /* + * if command was a full page read and the ELBC + * has the LTECCR register, then bits 12-15 (ppc order) of + * LTECCR indicates which 512 byte sub-pages had fixed errors. + * bits 28-31 are uncorrectable errors, marked elsewhere. + * for small page nand only 1 bit is used. + * if the ELBC doesn't have the lteccr register it reads 0 + * FIXME: 4 bits can be corrected on NANDs with 2k pages, so + * count the number of sub-pages with bitflips and update + * ecc_stats.corrected accordingly. + */ + if (lteccr & 0x000F000F) + out_be32(&lbc->lteccr, 0x000F000F); /* clear lteccr */ + if (lteccr & 0x000F0000) { + mtd->ecc_stats.corrected++; + elbc_fcm_ctrl->max_bitflips = 1; + } + } + + return 0; +} + +static void fsl_elbc_do_read(struct nand_chip *chip, int oob) +{ + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + + if (priv->page_size) { + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_CM1 << FIR_OP3_SHIFT) | + (FIR_OP_RBW << FIR_OP4_SHIFT)); + + out_be32(&lbc->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) | + (NAND_CMD_READSTART << FCR_CMD1_SHIFT)); + } else { + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_RBW << FIR_OP3_SHIFT)); + + if (oob) + out_be32(&lbc->fcr, NAND_CMD_READOOB << FCR_CMD0_SHIFT); + else + out_be32(&lbc->fcr, NAND_CMD_READ0 << FCR_CMD0_SHIFT); + } +} + +/* cmdfunc send commands to the FCM */ +static void fsl_elbc_cmdfunc(struct nand_chip *chip, unsigned int command, + int column, int page_addr) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + + elbc_fcm_ctrl->use_mdr = 0; + + /* clear the read buffer */ + elbc_fcm_ctrl->read_bytes = 0; + if (command != NAND_CMD_PAGEPROG) + elbc_fcm_ctrl->index = 0; + + switch (command) { + /* READ0 and READ1 read the entire buffer to use hardware ECC. */ + case NAND_CMD_READ1: + column += 256; + fallthrough; + case NAND_CMD_READ0: + dev_dbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_READ0, page_addr:" + " 0x%x, column: 0x%x.\n", page_addr, column); + + + out_be32(&lbc->fbcr, 0); /* read entire page to enable ECC */ + set_addr(mtd, 0, page_addr, 0); + + elbc_fcm_ctrl->read_bytes = mtd->writesize + mtd->oobsize; + elbc_fcm_ctrl->index += column; + + fsl_elbc_do_read(chip, 0); + fsl_elbc_run_command(mtd); + return; + + /* RNDOUT moves the pointer inside the page */ + case NAND_CMD_RNDOUT: + dev_dbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_RNDOUT, column: 0x%x.\n", + column); + + elbc_fcm_ctrl->index = column; + return; + + /* READOOB reads only the OOB because no ECC is performed. */ + case NAND_CMD_READOOB: + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_READOOB, page_addr:" + " 0x%x, column: 0x%x.\n", page_addr, column); + + out_be32(&lbc->fbcr, mtd->oobsize - column); + set_addr(mtd, column, page_addr, 1); + + elbc_fcm_ctrl->read_bytes = mtd->writesize + mtd->oobsize; + + fsl_elbc_do_read(chip, 1); + fsl_elbc_run_command(mtd); + return; + + case NAND_CMD_READID: + case NAND_CMD_PARAM: + dev_vdbg(priv->dev, "fsl_elbc_cmdfunc: NAND_CMD %x\n", command); + + out_be32(&lbc->fir, (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_UA << FIR_OP1_SHIFT) | + (FIR_OP_RBW << FIR_OP2_SHIFT)); + out_be32(&lbc->fcr, command << FCR_CMD0_SHIFT); + /* + * although currently it's 8 bytes for READID, we always read + * the maximum 256 bytes(for PARAM) + */ + out_be32(&lbc->fbcr, 256); + elbc_fcm_ctrl->read_bytes = 256; + elbc_fcm_ctrl->use_mdr = 1; + elbc_fcm_ctrl->mdr = column; + set_addr(mtd, 0, 0, 0); + fsl_elbc_run_command(mtd); + return; + + /* ERASE1 stores the block and page address */ + case NAND_CMD_ERASE1: + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_ERASE1, " + "page_addr: 0x%x.\n", page_addr); + set_addr(mtd, 0, page_addr, 0); + return; + + /* ERASE2 uses the block and page address from ERASE1 */ + case NAND_CMD_ERASE2: + dev_vdbg(priv->dev, "fsl_elbc_cmdfunc: NAND_CMD_ERASE2.\n"); + + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_PA << FIR_OP1_SHIFT) | + (FIR_OP_CM2 << FIR_OP2_SHIFT) | + (FIR_OP_CW1 << FIR_OP3_SHIFT) | + (FIR_OP_RS << FIR_OP4_SHIFT)); + + out_be32(&lbc->fcr, + (NAND_CMD_ERASE1 << FCR_CMD0_SHIFT) | + (NAND_CMD_STATUS << FCR_CMD1_SHIFT) | + (NAND_CMD_ERASE2 << FCR_CMD2_SHIFT)); + + out_be32(&lbc->fbcr, 0); + elbc_fcm_ctrl->read_bytes = 0; + elbc_fcm_ctrl->use_mdr = 1; + + fsl_elbc_run_command(mtd); + return; + + /* SEQIN sets up the addr buffer and all registers except the length */ + case NAND_CMD_SEQIN: { + __be32 fcr; + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG, " + "page_addr: 0x%x, column: 0x%x.\n", + page_addr, column); + + elbc_fcm_ctrl->column = column; + elbc_fcm_ctrl->use_mdr = 1; + + if (column >= mtd->writesize) { + /* OOB area */ + column -= mtd->writesize; + elbc_fcm_ctrl->oob = 1; + } else { + WARN_ON(column != 0); + elbc_fcm_ctrl->oob = 0; + } + + fcr = (NAND_CMD_STATUS << FCR_CMD1_SHIFT) | + (NAND_CMD_SEQIN << FCR_CMD2_SHIFT) | + (NAND_CMD_PAGEPROG << FCR_CMD3_SHIFT); + + if (priv->page_size) { + out_be32(&lbc->fir, + (FIR_OP_CM2 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_WB << FIR_OP3_SHIFT) | + (FIR_OP_CM3 << FIR_OP4_SHIFT) | + (FIR_OP_CW1 << FIR_OP5_SHIFT) | + (FIR_OP_RS << FIR_OP6_SHIFT)); + } else { + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_CM2 << FIR_OP1_SHIFT) | + (FIR_OP_CA << FIR_OP2_SHIFT) | + (FIR_OP_PA << FIR_OP3_SHIFT) | + (FIR_OP_WB << FIR_OP4_SHIFT) | + (FIR_OP_CM3 << FIR_OP5_SHIFT) | + (FIR_OP_CW1 << FIR_OP6_SHIFT) | + (FIR_OP_RS << FIR_OP7_SHIFT)); + + if (elbc_fcm_ctrl->oob) + /* OOB area --> READOOB */ + fcr |= NAND_CMD_READOOB << FCR_CMD0_SHIFT; + else + /* First 256 bytes --> READ0 */ + fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT; + } + + out_be32(&lbc->fcr, fcr); + set_addr(mtd, column, page_addr, elbc_fcm_ctrl->oob); + return; + } + + /* PAGEPROG reuses all of the setup from SEQIN and adds the length */ + case NAND_CMD_PAGEPROG: { + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_PAGEPROG " + "writing %d bytes.\n", elbc_fcm_ctrl->index); + + /* if the write did not start at 0 or is not a full page + * then set the exact length, otherwise use a full page + * write so the HW generates the ECC. + */ + if (elbc_fcm_ctrl->oob || elbc_fcm_ctrl->column != 0 || + elbc_fcm_ctrl->index != mtd->writesize + mtd->oobsize) + out_be32(&lbc->fbcr, + elbc_fcm_ctrl->index - elbc_fcm_ctrl->column); + else + out_be32(&lbc->fbcr, 0); + + fsl_elbc_run_command(mtd); + return; + } + + /* CMD_STATUS must read the status byte while CEB is active */ + /* Note - it does not wait for the ready line */ + case NAND_CMD_STATUS: + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_RBW << FIR_OP1_SHIFT)); + out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT); + out_be32(&lbc->fbcr, 1); + set_addr(mtd, 0, 0, 0); + elbc_fcm_ctrl->read_bytes = 1; + + fsl_elbc_run_command(mtd); + + /* The chip always seems to report that it is + * write-protected, even when it is not. + */ + setbits8(elbc_fcm_ctrl->addr, NAND_STATUS_WP); + return; + + /* RESET without waiting for the ready line */ + case NAND_CMD_RESET: + dev_dbg(priv->dev, "fsl_elbc_cmdfunc: NAND_CMD_RESET.\n"); + out_be32(&lbc->fir, FIR_OP_CM0 << FIR_OP0_SHIFT); + out_be32(&lbc->fcr, NAND_CMD_RESET << FCR_CMD0_SHIFT); + fsl_elbc_run_command(mtd); + return; + + default: + dev_err(priv->dev, + "fsl_elbc_cmdfunc: error, unsupported command 0x%x.\n", + command); + } +} + +static void fsl_elbc_select_chip(struct nand_chip *chip, int cs) +{ + /* The hardware does not seem to support multiple + * chips per bank. + */ +} + +/* + * Write buf to the FCM Controller Data Buffer + */ +static void fsl_elbc_write_buf(struct nand_chip *chip, const u8 *buf, int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + unsigned int bufsize = mtd->writesize + mtd->oobsize; + + if (len <= 0) { + dev_err(priv->dev, "write_buf of %d bytes", len); + elbc_fcm_ctrl->status = 0; + return; + } + + if ((unsigned int)len > bufsize - elbc_fcm_ctrl->index) { + dev_err(priv->dev, + "write_buf beyond end of buffer " + "(%d requested, %u available)\n", + len, bufsize - elbc_fcm_ctrl->index); + len = bufsize - elbc_fcm_ctrl->index; + } + + memcpy_toio(&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index], buf, len); + /* + * This is workaround for the weird elbc hangs during nand write, + * Scott Wood says: "...perhaps difference in how long it takes a + * write to make it through the localbus compared to a write to IMMR + * is causing problems, and sync isn't helping for some reason." + * Reading back the last byte helps though. + */ + in_8(&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index] + len - 1); + + elbc_fcm_ctrl->index += len; +} + +/* + * read a byte from either the FCM hardware buffer if it has any data left + * otherwise issue a command to read a single byte. + */ +static u8 fsl_elbc_read_byte(struct nand_chip *chip) +{ + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + + /* If there are still bytes in the FCM, then use the next byte. */ + if (elbc_fcm_ctrl->index < elbc_fcm_ctrl->read_bytes) + return in_8(&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index++]); + + dev_err(priv->dev, "read_byte beyond end of buffer\n"); + return ERR_BYTE; +} + +/* + * Read from the FCM Controller Data Buffer + */ +static void fsl_elbc_read_buf(struct nand_chip *chip, u8 *buf, int len) +{ + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + int avail; + + if (len < 0) + return; + + avail = min((unsigned int)len, + elbc_fcm_ctrl->read_bytes - elbc_fcm_ctrl->index); + memcpy_fromio(buf, &elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index], avail); + elbc_fcm_ctrl->index += avail; + + if (len > avail) + dev_err(priv->dev, + "read_buf beyond end of buffer " + "(%d requested, %d available)\n", + len, avail); +} + +/* This function is called after Program and Erase Operations to + * check for success or failure. + */ +static int fsl_elbc_wait(struct nand_chip *chip) +{ + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + + if (elbc_fcm_ctrl->status != LTESR_CC) + return NAND_STATUS_FAIL; + + /* The chip always seems to report that it is + * write-protected, even when it is not. + */ + return (elbc_fcm_ctrl->mdr & 0xff) | NAND_STATUS_WP; +} + +static int fsl_elbc_read_page(struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + + nand_read_page_op(chip, page, 0, buf, mtd->writesize); + if (oob_required) + fsl_elbc_read_buf(chip, chip->oob_poi, mtd->oobsize); + + if (fsl_elbc_wait(chip) & NAND_STATUS_FAIL) + mtd->ecc_stats.failed++; + + return elbc_fcm_ctrl->max_bitflips; +} + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_elbc_write_page(struct nand_chip *chip, const uint8_t *buf, + int oob_required, int page) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); + fsl_elbc_write_buf(chip, chip->oob_poi, mtd->oobsize); + + return nand_prog_page_end_op(chip); +} + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_elbc_write_subpage(struct nand_chip *chip, uint32_t offset, + uint32_t data_len, const uint8_t *buf, + int oob_required, int page) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + fsl_elbc_write_buf(chip, buf, mtd->writesize); + fsl_elbc_write_buf(chip, chip->oob_poi, mtd->oobsize); + return nand_prog_page_end_op(chip); +} + +static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv) +{ + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + struct nand_chip *chip = &priv->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + + dev_dbg(priv->dev, "eLBC Set Information for bank %d\n", priv->bank); + + /* Fill in fsl_elbc_mtd structure */ + mtd->dev.parent = priv->dev; + nand_set_flash_node(chip, priv->dev->of_node); + + /* set timeout to maximum */ + priv->fmr = 15 << FMR_CWTO_SHIFT; + if (in_be32(&lbc->bank[priv->bank].or) & OR_FCM_PGS) + priv->fmr |= FMR_ECCM; + + /* fill in nand_chip structure */ + /* set up function call table */ + chip->legacy.read_byte = fsl_elbc_read_byte; + chip->legacy.write_buf = fsl_elbc_write_buf; + chip->legacy.read_buf = fsl_elbc_read_buf; + chip->legacy.select_chip = fsl_elbc_select_chip; + chip->legacy.cmdfunc = fsl_elbc_cmdfunc; + chip->legacy.waitfunc = fsl_elbc_wait; + chip->legacy.set_features = nand_get_set_features_notsupp; + chip->legacy.get_features = nand_get_set_features_notsupp; + + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + + /* set up nand options */ + chip->bbt_options = NAND_BBT_USE_FLASH; + + chip->controller = &elbc_fcm_ctrl->controller; + nand_set_controller_data(chip, priv); + + return 0; +} + +static int fsl_elbc_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + unsigned int al; + + /* + * if ECC was not chosen in DT, decide whether to use HW or SW ECC from + * CS Base Register + */ + if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_INVALID) { + /* If CS Base Register selects full hardware ECC then use it */ + if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) == + BR_DECC_CHK_GEN) { + chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_ON_HOST; + } else { + /* otherwise fall back to default software ECC */ + chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT; + chip->ecc.algo = NAND_ECC_ALGO_HAMMING; + } + } + + switch (chip->ecc.engine_type) { + /* if HW ECC was chosen, setup ecc and oob layout */ + case NAND_ECC_ENGINE_TYPE_ON_HOST: + chip->ecc.read_page = fsl_elbc_read_page; + chip->ecc.write_page = fsl_elbc_write_page; + chip->ecc.write_subpage = fsl_elbc_write_subpage; + mtd_set_ooblayout(mtd, &fsl_elbc_ooblayout_ops); + chip->ecc.size = 512; + chip->ecc.bytes = 3; + chip->ecc.strength = 1; + break; + + /* if none or SW ECC was chosen, we do not need to set anything here */ + case NAND_ECC_ENGINE_TYPE_NONE: + case NAND_ECC_ENGINE_TYPE_SOFT: + case NAND_ECC_ENGINE_TYPE_ON_DIE: + break; + + default: + return -EINVAL; + } + + /* calculate FMR Address Length field */ + al = 0; + if (chip->pagemask & 0xffff0000) + al++; + if (chip->pagemask & 0xff000000) + al++; + + priv->fmr |= al << FMR_AL_SHIFT; + + dev_dbg(priv->dev, "fsl_elbc_init: nand->numchips = %d\n", + nanddev_ntargets(&chip->base)); + dev_dbg(priv->dev, "fsl_elbc_init: nand->chipsize = %lld\n", + nanddev_target_size(&chip->base)); + dev_dbg(priv->dev, "fsl_elbc_init: nand->pagemask = %8x\n", + chip->pagemask); + dev_dbg(priv->dev, "fsl_elbc_init: nand->legacy.chip_delay = %d\n", + chip->legacy.chip_delay); + dev_dbg(priv->dev, "fsl_elbc_init: nand->badblockpos = %d\n", + chip->badblockpos); + dev_dbg(priv->dev, "fsl_elbc_init: nand->chip_shift = %d\n", + chip->chip_shift); + dev_dbg(priv->dev, "fsl_elbc_init: nand->page_shift = %d\n", + chip->page_shift); + dev_dbg(priv->dev, "fsl_elbc_init: nand->phys_erase_shift = %d\n", + chip->phys_erase_shift); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.engine_type = %d\n", + chip->ecc.engine_type); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.steps = %d\n", + chip->ecc.steps); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.bytes = %d\n", + chip->ecc.bytes); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.total = %d\n", + chip->ecc.total); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->ooblayout = %p\n", + mtd->ooblayout); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->flags = %08x\n", mtd->flags); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->size = %lld\n", mtd->size); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->erasesize = %d\n", + mtd->erasesize); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->writesize = %d\n", + mtd->writesize); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->oobsize = %d\n", + mtd->oobsize); + + /* adjust Option Register and ECC to match Flash page size */ + if (mtd->writesize == 512) { + priv->page_size = 0; + clrbits32(&lbc->bank[priv->bank].or, OR_FCM_PGS); + } else if (mtd->writesize == 2048) { + priv->page_size = 1; + setbits32(&lbc->bank[priv->bank].or, OR_FCM_PGS); + } else { + dev_err(priv->dev, + "fsl_elbc_init: page size %d is not supported\n", + mtd->writesize); + return -ENOTSUPP; + } + + return 0; +} + +static const struct nand_controller_ops fsl_elbc_controller_ops = { + .attach_chip = fsl_elbc_attach_chip, +}; + +static int fsl_elbc_chip_remove(struct fsl_elbc_mtd *priv) +{ + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + struct mtd_info *mtd = nand_to_mtd(&priv->chip); + + kfree(mtd->name); + + if (priv->vbase) + iounmap(priv->vbase); + + elbc_fcm_ctrl->chips[priv->bank] = NULL; + kfree(priv); + return 0; +} + +static DEFINE_MUTEX(fsl_elbc_nand_mutex); + +static int fsl_elbc_nand_probe(struct platform_device *pdev) +{ + struct fsl_lbc_regs __iomem *lbc; + struct fsl_elbc_mtd *priv; + struct resource res; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl; + static const char *part_probe_types[] + = { "cmdlinepart", "RedBoot", "ofpart", NULL }; + int ret; + int bank; + struct device *dev; + struct device_node *node = pdev->dev.of_node; + struct mtd_info *mtd; + + if (!fsl_lbc_ctrl_dev || !fsl_lbc_ctrl_dev->regs) + return -ENODEV; + lbc = fsl_lbc_ctrl_dev->regs; + dev = fsl_lbc_ctrl_dev->dev; + + /* get, allocate and map the memory resource */ + ret = of_address_to_resource(node, 0, &res); + if (ret) { + dev_err(dev, "failed to get resource\n"); + return ret; + } + + /* find which chip select it is connected to */ + for (bank = 0; bank < MAX_BANKS; bank++) + if ((in_be32(&lbc->bank[bank].br) & BR_V) && + (in_be32(&lbc->bank[bank].br) & BR_MSEL) == BR_MS_FCM && + (in_be32(&lbc->bank[bank].br) & + in_be32(&lbc->bank[bank].or) & BR_BA) + == fsl_lbc_addr(res.start)) + break; + + if (bank >= MAX_BANKS) { + dev_err(dev, "address did not match any chip selects\n"); + return -ENODEV; + } + + priv = kzalloc(sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + mutex_lock(&fsl_elbc_nand_mutex); + if (!fsl_lbc_ctrl_dev->nand) { + elbc_fcm_ctrl = kzalloc(sizeof(*elbc_fcm_ctrl), GFP_KERNEL); + if (!elbc_fcm_ctrl) { + mutex_unlock(&fsl_elbc_nand_mutex); + ret = -ENOMEM; + goto err; + } + elbc_fcm_ctrl->counter++; + + nand_controller_init(&elbc_fcm_ctrl->controller); + fsl_lbc_ctrl_dev->nand = elbc_fcm_ctrl; + } else { + elbc_fcm_ctrl = fsl_lbc_ctrl_dev->nand; + } + mutex_unlock(&fsl_elbc_nand_mutex); + + elbc_fcm_ctrl->chips[bank] = priv; + priv->bank = bank; + priv->ctrl = fsl_lbc_ctrl_dev; + priv->dev = &pdev->dev; + dev_set_drvdata(priv->dev, priv); + + priv->vbase = ioremap(res.start, resource_size(&res)); + if (!priv->vbase) { + dev_err(dev, "failed to map chip region\n"); + ret = -ENOMEM; + goto err; + } + + mtd = nand_to_mtd(&priv->chip); + mtd->name = kasprintf(GFP_KERNEL, "%llx.flash", (u64)res.start); + if (!nand_to_mtd(&priv->chip)->name) { + ret = -ENOMEM; + goto err; + } + + ret = fsl_elbc_chip_init(priv); + if (ret) + goto err; + + priv->chip.controller->ops = &fsl_elbc_controller_ops; + ret = nand_scan(&priv->chip, 1); + if (ret) + goto err; + + /* First look for RedBoot table or partitions on the command + * line, these take precedence over device tree information */ + ret = mtd_device_parse_register(mtd, part_probe_types, NULL, NULL, 0); + if (ret) + goto cleanup_nand; + + pr_info("eLBC NAND device at 0x%llx, bank %d\n", + (unsigned long long)res.start, priv->bank); + + return 0; + +cleanup_nand: + nand_cleanup(&priv->chip); +err: + fsl_elbc_chip_remove(priv); + + return ret; +} + +static int fsl_elbc_nand_remove(struct platform_device *pdev) +{ + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = fsl_lbc_ctrl_dev->nand; + struct fsl_elbc_mtd *priv = dev_get_drvdata(&pdev->dev); + struct nand_chip *chip = &priv->chip; + int ret; + + ret = mtd_device_unregister(nand_to_mtd(chip)); + WARN_ON(ret); + nand_cleanup(chip); + + fsl_elbc_chip_remove(priv); + + mutex_lock(&fsl_elbc_nand_mutex); + elbc_fcm_ctrl->counter--; + if (!elbc_fcm_ctrl->counter) { + fsl_lbc_ctrl_dev->nand = NULL; + kfree(elbc_fcm_ctrl); + } + mutex_unlock(&fsl_elbc_nand_mutex); + + return 0; + +} + +static const struct of_device_id fsl_elbc_nand_match[] = { + { .compatible = "fsl,elbc-fcm-nand", }, + {} +}; +MODULE_DEVICE_TABLE(of, fsl_elbc_nand_match); + +static struct platform_driver fsl_elbc_nand_driver = { + .driver = { + .name = "fsl,elbc-fcm-nand", + .of_match_table = fsl_elbc_nand_match, + }, + .probe = fsl_elbc_nand_probe, + .remove = fsl_elbc_nand_remove, +}; + +module_platform_driver(fsl_elbc_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Freescale"); +MODULE_DESCRIPTION("Freescale Enhanced Local Bus Controller MTD NAND driver"); |