1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
*
* Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
*/
/dts-v1/;
#include "mmp3.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Dell Ariel";
compatible = "dell,wyse-ariel", "marvell,mmp3";
aliases {
serial2 = &uart3;
};
chosen {
#address-cells = <0x1>;
#size-cells = <0x1>;
ranges;
bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
};
memory@0 {
linux,usable-memory = <0x0 0x7f600000>;
available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
reg = <0x0 0x80000000>;
device_type = "memory";
};
};
&uart3 {
status = "okay";
};
&rtc {
status = "okay";
};
&usb_otg0 {
status = "okay";
};
&usb_otg_phy0 {
status = "okay";
};
&hsic0 {
status = "okay";
usb1@1 {
compatible = "usb424,2640";
reg = <0x01>;
#address-cells = <0x01>;
#size-cells = <0x00>;
mass-storage@1 {
compatible = "usb424,4040";
reg = <0x01>;
status = "disabled";
};
};
};
&hsic_phy0 {
status = "okay";
reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>;
};
&mmc3 {
status = "okay";
max-frequency = <50000000>;
status = "okay";
bus-width = <8>;
non-removable;
cap-mmc-highspeed;
};
&twsi1 {
status = "okay";
rtc@68 {
compatible = "dallas,ds1338";
reg = <0x68>;
status = "okay";
};
};
&twsi3 {
status = "okay";
};
&twsi4 {
status = "okay";
};
&ssp1 {
status = "okay";
cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
firmware-flash@0 {
compatible = "winbond,w25q32", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <104000000>;
m25p,fast-read;
};
};
&ssp2 {
cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
status = "okay";
};
&gpu_2d {
status = "okay";
};
&gpu_3d {
status = "okay";
};
|
