1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
* Copyright (c) 2019, Linaro Limited
*/
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
/ {
thermal-zones {
pm8150b {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pm8150b_temp>;
trips {
trip0 {
temperature = <95000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <115000>;
hysteresis = <0>;
type = "hot";
};
trip2 {
temperature = <145000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pmic@2 {
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
reg = <0x2 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
power-on@800 {
compatible = "qcom,pm8916-pon";
reg = <0x0800>;
status = "disabled";
};
pm8150b_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
io-channels = <&pm8150b_adc ADC5_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pm8150b_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
ref-gnd@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
label = "ref_gnd";
};
vref-1p25@1 {
reg = <ADC5_1P25VREF>;
qcom,pre-scaling = <1 1>;
label = "vref_1p25";
};
die-temp@6 {
reg = <ADC5_DIE_TEMP>;
qcom,pre-scaling = <1 1>;
label = "die_temp";
};
chg-temp@9 {
reg = <ADC5_CHG_TEMP>;
qcom,pre-scaling = <1 1>;
label = "chg_temp";
};
};
pm8150b_gpios: gpio@c000 {
compatible = "qcom,pm8150b-gpio";
reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmic@3 {
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
reg = <0x3 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
};
};
|
