1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
|
/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2014, 2015 Intel Corporation; author Matt Fleming
*
* Early support for invoking 32-bit EFI services from a 64-bit kernel.
*
* Because this thunking occurs before ExitBootServices() we have to
* restore the firmware's 32-bit GDT before we make EFI serivce calls,
* since the firmware's 32-bit IDT is still currently installed and it
* needs to be able to service interrupts.
*
* On the plus side, we don't have to worry about mangling 64-bit
* addresses into 32-bits because we're executing with an identity
* mapped pagetable and haven't transitioned to 64-bit virtual addresses
* yet.
*/
#include <linux/linkage.h>
#include <asm/msr.h>
#include <asm/page_types.h>
#include <asm/processor-flags.h>
#include <asm/segment.h>
.code64
.text
SYM_FUNC_START(__efi64_thunk)
push %rbp
push %rbx
leaq 1f(%rip), %rbp
movl %ds, %eax
push %rax
movl %es, %eax
push %rax
movl %ss, %eax
push %rax
/*
* Convert x86-64 ABI params to i386 ABI
*/
subq $32, %rsp
movl %esi, 0x0(%rsp)
movl %edx, 0x4(%rsp)
movl %ecx, 0x8(%rsp)
movl %r8d, 0xc(%rsp)
movl %r9d, 0x10(%rsp)
leaq 0x14(%rsp), %rbx
sgdt (%rbx)
/*
* Switch to gdt with 32-bit segments. This is the firmware GDT
* that was installed when the kernel started executing. This
* pointer was saved at the EFI stub entry point in head_64.S.
*
* Pass the saved DS selector to the 32-bit code, and use far return to
* restore the saved CS selector.
*/
leaq efi32_boot_gdt(%rip), %rax
lgdt (%rax)
movzwl efi32_boot_ds(%rip), %edx
movzwq efi32_boot_cs(%rip), %rax
pushq %rax
leaq efi_enter32(%rip), %rax
pushq %rax
lretq
1: addq $32, %rsp
movq %rdi, %rax
pop %rbx
movl %ebx, %ss
pop %rbx
movl %ebx, %es
pop %rbx
movl %ebx, %ds
/* Clear out 32-bit selector from FS and GS */
xorl %ebx, %ebx
movl %ebx, %fs
movl %ebx, %gs
/*
* Convert 32-bit status code into 64-bit.
*/
roll $1, %eax
rorq $1, %rax
pop %rbx
pop %rbp
RET
SYM_FUNC_END(__efi64_thunk)
.code32
/*
* EFI service pointer must be in %edi.
*
* The stack should represent the 32-bit calling convention.
*/
SYM_FUNC_START_LOCAL(efi_enter32)
/* Load firmware selector into data and stack segment registers */
movl %edx, %ds
movl %edx, %es
movl %edx, %fs
movl %edx, %gs
movl %edx, %ss
/* Reload pgtables */
movl %cr3, %eax
movl %eax, %cr3
/* Disable paging */
movl %cr0, %eax
btrl $X86_CR0_PG_BIT, %eax
movl %eax, %cr0
/* Disable long mode via EFER */
movl $MSR_EFER, %ecx
rdmsr
btrl $_EFER_LME, %eax
wrmsr
call *%edi
/* We must preserve return value */
movl %eax, %edi
/*
* Some firmware will return with interrupts enabled. Be sure to
* disable them before we switch GDTs.
*/
cli
lgdtl (%ebx)
movl %cr4, %eax
btsl $(X86_CR4_PAE_BIT), %eax
movl %eax, %cr4
movl %cr3, %eax
movl %eax, %cr3
movl $MSR_EFER, %ecx
rdmsr
btsl $_EFER_LME, %eax
wrmsr
xorl %eax, %eax
lldt %ax
pushl $__KERNEL_CS
pushl %ebp
/* Enable paging */
movl %cr0, %eax
btsl $X86_CR0_PG_BIT, %eax
movl %eax, %cr0
lret
SYM_FUNC_END(efi_enter32)
.data
.balign 8
SYM_DATA_START(efi32_boot_gdt)
.word 0
.quad 0
SYM_DATA_END(efi32_boot_gdt)
SYM_DATA_START(efi32_boot_cs)
.word 0
SYM_DATA_END(efi32_boot_cs)
SYM_DATA_START(efi32_boot_ds)
.word 0
SYM_DATA_END(efi32_boot_ds)
|
