diff options
Diffstat (limited to 'doc/rbd/iscsi-target-cli-manual-install.rst')
| -rw-r--r-- | doc/rbd/iscsi-target-cli-manual-install.rst | 190 |
1 files changed, 190 insertions, 0 deletions
diff --git a/doc/rbd/iscsi-target-cli-manual-install.rst b/doc/rbd/iscsi-target-cli-manual-install.rst new file mode 100644 index 00000000..ccc422e0 --- /dev/null +++ b/doc/rbd/iscsi-target-cli-manual-install.rst @@ -0,0 +1,190 @@ +============================== +Manual ceph-iscsi Installation +============================== + +**Requirements** + +To complete the installation of ceph-iscsi, there are 4 steps: + +1. Install common packages from your Linux distribution's software repository +2. Install Git to fetch the remaining packages directly from their Git repositories +3. Ensure a compatible kernel is used +4. Install all the components of ceph-iscsi and start associated daemons: + + - tcmu-runner + - rtslib-fb + - configshell-fb + - targetcli-fb + - ceph-iscsi + + +1. Install Common Packages +========================== + +The following packages will be used by ceph-iscsi and target tools. +They must be installed from your Linux distribution's software repository +on each machine that will be a iSCSI gateway: + +- libnl3 +- libkmod +- librbd1 +- pyparsing +- python kmod +- python pyudev +- python gobject +- python urwid +- python pyparsing +- python rados +- python rbd +- python netifaces +- python crypto +- python requests +- python flask +- pyOpenSSL + + +2. Install Git +============== + +In order to install all the packages needed to run iSCSI with Ceph, you need to download them directly from their repository by using Git. +On CentOS/RHEL execute: + +:: + + > sudo yum install git + +On Debian/Ubuntu execute: + +:: + + > sudo apt install git + +To know more about Git and how it works, please, visit https://git-scm.com + + +3. Ensure a compatible kernel is used +===================================== + +Ensure you use a supported kernel that contains the required Ceph iSCSI patches: + +- all Linux distribution with a kernel v4.16 or newer, or +- Red Hat Enterprise Linux or CentOS 7.5 or later (in these distributions ceph-iscsi support is backported) + +If you are already using a compatible kernel, you can go to next step. +However, if you are NOT using a compatible kernel then check your distro's +documentation for specific instructions on how to build this kernel. The only +Ceph iSCSI specific requirements are that the following build options must be +enabled: + + :: + + CONFIG_TARGET_CORE=m + CONFIG_TCM_USER2=m + CONFIG_ISCSI_TARGET=m + + +4. Install ceph-iscsi +======================================================== + +Finally, the remaining tools can be fetched directly from their Git repositories and their associated services started + + +tcmu-runner +----------- + + Installation: + + :: + + > git clone https://github.com/open-iscsi/tcmu-runner + > cd tcmu-runner + + Run the following command to install all the needed dependencies: + + :: + + > ./extra/install_dep.sh + + Now you can build the tcmu-runner. + To do so, use the following build command: + + :: + + > cmake -Dwith-glfs=false -Dwith-qcow=false -DSUPPORT_SYSTEMD=ON -DCMAKE_INSTALL_PREFIX=/usr + > make install + + Enable and start the daemon: + + :: + + > systemctl daemon-reload + > systemctl enable tcmu-runner + > systemctl start tcmu-runner + + +rtslib-fb +--------- + + Installation: + + :: + + > git clone https://github.com/open-iscsi/rtslib-fb.git + > cd rtslib-fb + > python setup.py install + +configshell-fb +-------------- + + Installation: + + :: + + > git clone https://github.com/open-iscsi/configshell-fb.git + > cd configshell-fb + > python setup.py install + +targetcli-fb +------------ + + Installation: + + :: + + > git clone https://github.com/open-iscsi/targetcli-fb.git + > cd targetcli-fb + > python setup.py install + > mkdir /etc/target + > mkdir /var/target + + .. warning:: The ceph-iscsi tools assume they are managing all targets + on the system. If targets have been setup and are being managed by + targetcli the target service must be disabled. + +ceph-iscsi +----------------- + + Installation: + + :: + + > git clone https://github.com/ceph/ceph-iscsi.git + > cd ceph-iscsi + > python setup.py install --install-scripts=/usr/bin + > cp usr/lib/systemd/system/rbd-target-gw.service /lib/systemd/system + > cp usr/lib/systemd/system/rbd-target-api.service /lib/systemd/system + + Enable and start the daemon: + + :: + + > systemctl daemon-reload + > systemctl enable rbd-target-gw + > systemctl start rbd-target-gw + > systemctl enable rbd-target-api + > systemctl start rbd-target-api + +Installation is complete. Proceed to the setup section in the +`main ceph-iscsi CLI page`_. + +.. _`main ceph-iscsi CLI page`: ../iscsi-target-cli |