Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

14 files changed, 2017 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt
new file mode 100644
index 000000000..320607cbb
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt
@@ -0,0 +1,148 @@
+Atheros AR9331 built-in switch
+=============================
+
+It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
+MDIO bus. All PHYs are built-in as well.
+
+Required properties:
+
+ - compatible: should be: "qca,ar9331-switch"
+ - reg: Address on the MII bus for the switch.
+ - resets : Must contain an entry for each entry in reset-names.
+ - reset-names : Must include the following entries: "switch"
+ - interrupt-parent: Phandle to the parent interrupt controller
+ - interrupts: IRQ line for the switch
+ - interrupt-controller: Indicates the switch is itself an interrupt
+   controller. This is used for the PHY interrupts.
+ - #interrupt-cells: must be 1
+ - mdio: Container of PHY and devices on the switches MDIO bus.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+Examples:
+
+eth0: ethernet@19000000 {
+	compatible = "qca,ar9330-eth";
+	reg = <0x19000000 0x200>;
+	interrupts = <4>;
+
+	resets = <&rst 9>, <&rst 22>;
+	reset-names = "mac", "mdio";
+	clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+	clock-names = "eth", "mdio";
+
+	phy-mode = "mii";
+	phy-handle = <&phy_port4>;
+};
+
+eth1: ethernet@1a000000 {
+	compatible = "qca,ar9330-eth";
+	reg = <0x1a000000 0x200>;
+	interrupts = <5>;
+	resets = <&rst 13>, <&rst 23>;
+	reset-names = "mac", "mdio";
+	clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+	clock-names = "eth", "mdio";
+
+	phy-mode = "gmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch10: switch@10 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			compatible = "qca,ar9331-switch";
+			reg = <0x10>;
+			resets = <&rst 8>;
+			reset-names = "switch";
+
+			interrupt-parent = <&miscintc>;
+			interrupts = <12>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch_port0: port@0 {
+					reg = <0x0>;
+					label = "cpu";
+					ethernet = <&eth1>;
+
+					phy-mode = "gmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				switch_port1: port@1 {
+					reg = <0x1>;
+					phy-handle = <&phy_port0>;
+					phy-mode = "internal";
+				};
+
+				switch_port2: port@2 {
+					reg = <0x2>;
+					phy-handle = <&phy_port1>;
+					phy-mode = "internal";
+				};
+
+				switch_port3: port@3 {
+					reg = <0x3>;
+					phy-handle = <&phy_port2>;
+					phy-mode = "internal";
+				};
+
+				switch_port4: port@4 {
+					reg = <0x4>;
+					phy-handle = <&phy_port3>;
+					phy-mode = "internal";
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				interrupt-parent = <&switch10>;
+
+				phy_port0: phy@0 {
+					reg = <0x0>;
+					interrupts = <0>;
+				};
+
+				phy_port1: phy@1 {
+					reg = <0x1>;
+					interrupts = <0>;
+				};
+
+				phy_port2: phy@2 {
+					reg = <0x2>;
+					interrupts = <0>;
+				};
+
+				phy_port3: phy@3 {
+					reg = <0x3>;
+					interrupts = <0>;
+				};
+
+				phy_port4: phy@4 {
+					reg = <0x4>;
+					interrupts = <0>;
+				};
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt
new file mode 100644
index 000000000..f1487a751
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/b53.txt
@@ -0,0 +1,149 @@
+Broadcom BCM53xx Ethernet switches
+==================================
+
+Required properties:
+
+- compatible: For external switch chips, compatible string must be exactly one
+  of: "brcm,bcm5325"
+      "brcm,bcm53115"
+      "brcm,bcm53125"
+      "brcm,bcm53128"
+      "brcm,bcm5365"
+      "brcm,bcm5395"
+      "brcm,bcm5389"
+      "brcm,bcm5397"
+      "brcm,bcm5398"
+
+  For the BCM11360 SoC, must be:
+      "brcm,bcm11360-srab" and the mandatory "brcm,cygnus-srab" string
+
+  For the BCM5310x SoCs with an integrated switch, must be one of:
+      "brcm,bcm53010-srab"
+      "brcm,bcm53011-srab"
+      "brcm,bcm53012-srab"
+      "brcm,bcm53018-srab"
+      "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string
+
+  For the BCM5831X/BCM1140x SoCs with an integrated switch, must be one of:
+      "brcm,bcm11404-srab"
+      "brcm,bcm11407-srab"
+      "brcm,bcm11409-srab"
+      "brcm,bcm58310-srab"
+      "brcm,bcm58311-srab"
+      "brcm,bcm58313-srab" and the mandatory "brcm,omega-srab" string
+
+  For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of:
+      "brcm,bcm58522-srab"
+      "brcm,bcm58523-srab"
+      "brcm,bcm58525-srab"
+      "brcm,bcm58622-srab"
+      "brcm,bcm58623-srab"
+      "brcm,bcm58625-srab"
+      "brcm,bcm88312-srab" and the mandatory "brcm,nsp-srab string
+
+  For the BCM63xx/33xx SoCs with an integrated switch, must be one of:
+      "brcm,bcm3384-switch"
+      "brcm,bcm6328-switch"
+      "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
+
+Required properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg: a total of 3 register base addresses, the first one must be the
+   Switch Register Access block base, the second is the port 5/4 mux
+   configuration register and the third one is the SGMII configuration
+   and status register base address.
+
+ - interrupts: a total of 13 interrupts must be specified, in the following
+   order: port 0-5, 7-8 link status change, then the integrated PHY interrupt,
+   then the timestamping interrupt and the sleep timer interrupts for ports
+   5,7,8.
+
+Optional properties for BCM585xx/586xx/88312 SoCs:
+
+  - reg-names: a total of 3 names matching the 3 base register address, must
+    be in the following order:
+	"srab"
+	"mux_config"
+	"sgmii_config"
+
+  - interrupt-names: a total of 13 names matching the 13 interrupts specified
+    must be in the following order:
+	"link_state_p0"
+	"link_state_p1"
+	"link_state_p2"
+	"link_state_p3"
+	"link_state_p4"
+	"link_state_p5"
+	"link_state_p7"
+	"link_state_p8"
+	"phy"
+	"ts"
+	"imp_sleep_timer_p5"
+	"imp_sleep_timer_p7"
+	"imp_sleep_timer_p8"
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+
+Examples:
+
+Ethernet switch connected via MDIO to the host, CPU port wired to eth0:
+
+	eth0: ethernet@10001000 {
+		compatible = "brcm,unimac";
+		reg = <0x10001000 0x1000>;
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+
+	mdio0: mdio@10000000 {
+		compatible = "brcm,unimac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0: ethernet-switch@1e {
+			compatible = "brcm,bcm53125";
+			reg = <30>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port0@0 {
+					reg = <0>;
+					label = "lan1";
+				};
+
+				port1@1 {
+					reg = <1>;
+					label = "lan2";
+				};
+
+				port5@5 {
+					reg = <5>;
+					label = "cable-modem";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+					phy-mode = "rgmii-txid";
+				};
+
+				port8@8 {
+					reg = <8>;
+					label = "cpu";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+					phy-mode = "rgmii-txid";
+					ethernet = <&eth0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
new file mode 100644
index 000000000..dab208b5c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -0,0 +1,4 @@
+Distributed Switch Architecture Device Tree Bindings
+----------------------------------------------------
+
+See Documentation/devicetree/bindings/net/dsa/dsa.yaml for the documentation.
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml
new file mode 100644
index 000000000..a765ceba2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml
@@ -0,0 +1,94 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/dsa.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ethernet Switch Device Tree Bindings
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Florian Fainelli <f.fainelli@gmail.com>
+  - Vivien Didelot <vivien.didelot@gmail.com>
+
+description:
+  This binding represents Ethernet Switches which have a dedicated CPU
+  port. That port is usually connected to an Ethernet Controller of the
+  SoC. Such setups are typical for embedded devices.
+
+select: false
+
+properties:
+  $nodename:
+    pattern: "^switch(@.*)?$"
+
+  dsa,member:
+    minItems: 2
+    maxItems: 2
+    description:
+      A two element list indicates which DSA cluster, and position within the
+      cluster a switch takes. <0 0> is cluster 0, switch 0. <0 1> is cluster 0,
+      switch 1. <1 0> is cluster 1, switch 0. A switch not part of any cluster
+      (single device hanging off a CPU port) must not specify this property
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+
+patternProperties:
+  "^(ethernet-)?ports$":
+    type: object
+    properties:
+      '#address-cells':
+        const: 1
+      '#size-cells':
+        const: 0
+
+    patternProperties:
+      "^(ethernet-)?port@[0-9]+$":
+        type: object
+        description: Ethernet switch ports
+
+        properties:
+          reg:
+            description: Port number
+
+          label:
+            description:
+              Describes the label associated with this port, which will become
+              the netdev name
+            $ref: /schemas/types.yaml#definitions/string
+
+          link:
+            description:
+              Should be a list of phandles to other switch's DSA port. This
+              port is used as the outgoing port towards the phandle ports. The
+              full routing information must be given, not just the one hop
+              routes to neighbouring switches
+            $ref: /schemas/types.yaml#definitions/phandle-array
+
+          ethernet:
+            description:
+              Should be a phandle to a valid Ethernet device node.  This host
+              device is what the switch port is connected to
+            $ref: /schemas/types.yaml#definitions/phandle
+
+          phy-handle: true
+
+          phy-mode: true
+
+          fixed-link: true
+
+          mac-address: true
+
+        required:
+          - reg
+
+        additionalProperties: false
+
+oneOf:
+  - required:
+      - ports
+  - required:
+      - ethernet-ports
+
+additionalProperties: true
+
+...
diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt
new file mode 100644
index 000000000..95e91e841
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt
@@ -0,0 +1,125 @@
+Microchip KSZ Series Ethernet switches
+==================================
+
+Required properties:
+
+- compatible: For external switch chips, compatible string must be exactly one
+  of the following:
+  - "microchip,ksz8765"
+  - "microchip,ksz8794"
+  - "microchip,ksz8795"
+  - "microchip,ksz9477"
+  - "microchip,ksz9897"
+  - "microchip,ksz9896"
+  - "microchip,ksz9567"
+  - "microchip,ksz8565"
+  - "microchip,ksz9893"
+  - "microchip,ksz9563"
+  - "microchip,ksz8563"
+
+Optional properties:
+
+- reset-gpios		: Should be a gpio specifier for a reset line
+- microchip,synclko-125 : Set if the output SYNCLKO frequency should be set to
+			  125MHz instead of 25MHz.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+
+Examples:
+
+Ethernet switch connected via SPI to the host, CPU port wired to eth0:
+
+	eth0: ethernet@10001000 {
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+
+	spi1: spi@f8008000 {
+		pinctrl-0 = <&pinctrl_spi_ksz>;
+		cs-gpios = <&pioC 25 0>;
+		id = <1>;
+
+		ksz9477: ksz9477@0 {
+			compatible = "microchip,ksz9477";
+			reg = <0>;
+
+			spi-max-frequency = <44000000>;
+			spi-cpha;
+			spi-cpol;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "lan1";
+				};
+				port@1 {
+					reg = <1>;
+					label = "lan2";
+				};
+				port@2 {
+					reg = <2>;
+					label = "lan3";
+				};
+				port@3 {
+					reg = <3>;
+					label = "lan4";
+				};
+				port@4 {
+					reg = <4>;
+					label = "lan5";
+				};
+				port@5 {
+					reg = <5>;
+					label = "cpu";
+					ethernet = <&eth0>;
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+		ksz8565: ksz8565@0 {
+			compatible = "microchip,ksz8565";
+			reg = <0>;
+
+			spi-max-frequency = <44000000>;
+			spi-cpha;
+			spi-cpol;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "lan1";
+				};
+				port@1 {
+					reg = <1>;
+					label = "lan2";
+				};
+				port@2 {
+					reg = <2>;
+					label = "lan3";
+				};
+				port@3 {
+					reg = <3>;
+					label = "lan4";
+				};
+				port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&eth0>;
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
new file mode 100644
index 000000000..464d6bf87
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
@@ -0,0 +1,102 @@
+SMSC/MicroChip LAN9303 three port ethernet switch
+-------------------------------------------------
+
+Required properties:
+
+- compatible: should be
+  - "smsc,lan9303-i2c" for I2C managed mode
+    or
+  - "smsc,lan9303-mdio" for mdio managed mode
+
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+- reset-duration: reset duration in milliseconds, defaults to 200 ms
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. The CPU port of this switch is always port 0.
+
+Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is
+configured to use 1/2/3 instead. This hardware configuration will be
+auto-detected and mapped accordingly.
+
+Example:
+
+I2C managed mode:
+
+	master: masterdevice@X {
+
+		fixed-link { /* RMII fixed link to LAN9303 */
+			speed = <100>;
+			full-duplex;
+		};
+	};
+
+	switch: switch@a {
+		compatible = "smsc,lan9303-i2c";
+		reg = <0xa>;
+		reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+		reset-duration = <200>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 { /* RMII fixed link to master */
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&master>;
+			};
+
+			port@1 { /* external port 1 */
+				reg = <1>;
+				label = "lan1";
+			};
+
+			port@2 { /* external port 2 */
+				reg = <2>;
+				label = "lan2";
+			};
+		};
+	};
+
+MDIO managed mode:
+
+	master: masterdevice@X {
+		phy-handle = <&switch>;
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch: switch-phy@0 {
+				compatible = "smsc,lan9303-mdio";
+				reg = <0>;
+				reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+				reset-duration = <100>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						label = "cpu";
+						ethernet = <&master>;
+					};
+
+					port@1 { /* external port 1 */
+						reg = <1>;
+						label = "lan1";
+					};
+
+					port@2 { /* external port 2 */
+						reg = <2>;
+						label = "lan2";
+					};
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt
new file mode 100644
index 000000000..886cbe8ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt
@@ -0,0 +1,143 @@
+Lantiq GSWIP Ethernet switches
+==================================
+
+Required properties for GSWIP core:
+
+- compatible	: "lantiq,xrx200-gswip" for the embedded GSWIP in the
+		  xRX200 SoC
+- reg		: memory range of the GSWIP core registers
+		: memory range of the GSWIP MDIO registers
+		: memory range of the GSWIP MII registers
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of
+additional required and optional properties.
+
+
+Required properties for MDIO bus:
+- compatible	: "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP
+		  core of the xRX200 SoC and the PHYs connected to it.
+
+See Documentation/devicetree/bindings/net/mdio.txt for a list of additional
+required and optional properties.
+
+
+Required properties for GPHY firmware loading:
+- compatible	: "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"
+		  "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw"
+		  "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw"
+		  for the loading of the firmware into the embedded
+		  GPHY core of the SoC.
+- lantiq,rcu	: reference to the rcu syscon
+
+The GPHY firmware loader has a list of GPHY entries, one for each
+embedded GPHY
+
+- reg		: Offset of the GPHY firmware register in the RCU
+		  register range
+- resets	: list of resets of the embedded GPHY
+- reset-names	: list of names of the resets
+
+Example:
+
+Ethernet switch on the VRX200 SoC:
+
+switch@e108000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "lantiq,xrx200-gswip";
+	reg = <	0xe108000 0x3100	/* switch */
+		0xe10b100 0xd8		/* mdio */
+		0xe10b1d8 0x130		/* mii */
+		>;
+	dsa,member = <0 0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan3";
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan4";
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+			phy-mode = "internal";
+			phy-handle = <&phy11>;
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan1";
+			phy-mode = "internal";
+			phy-handle = <&phy13>;
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "wan";
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+		};
+
+		port@6 {
+			reg = <0x6>;
+			label = "cpu";
+			ethernet = <&eth0>;
+		};
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "lantiq,xrx200-mdio";
+		reg = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0x0>;
+		};
+		phy1: ethernet-phy@1 {
+			reg = <0x1>;
+		};
+		phy5: ethernet-phy@5 {
+			reg = <0x5>;
+		};
+		phy11: ethernet-phy@11 {
+			reg = <0x11>;
+		};
+		phy13: ethernet-phy@13 {
+			reg = <0x13>;
+		};
+	};
+
+	gphy-fw {
+		compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw";
+		lantiq,rcu = <&rcu0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gphy@20 {
+			reg = <0x20>;
+
+			resets = <&reset0 31 30>;
+			reset-names = "gphy";
+		};
+
+		gphy@68 {
+			reg = <0x68>;
+
+			resets = <&reset0 29 28>;
+			reset-names = "gphy";
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt
new file mode 100644
index 000000000..30c11fea4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt
@@ -0,0 +1,109 @@
+Marvell DSA Switch Device Tree Bindings
+---------------------------------------
+
+WARNING: This binding is currently unstable. Do not program it into a
+FLASH never to be changed again. Once this binding is stable, this
+warning will be removed.
+
+If you need a stable binding, use the old dsa.txt binding.
+
+Marvell Switches are MDIO devices. The following properties should be
+placed as a child node of an mdio device.
+
+The properties described here are those specific to Marvell devices.
+Additional required and optional properties can be found in dsa.txt.
+
+The compatibility string is used only to find an identification register,
+which is at a different MDIO base address in different switch families.
+- "marvell,mv88e6085"	: Switch has base address 0x10. Use with models:
+			  6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
+			  6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
+			  6341, 6350, 6351, 6352
+- "marvell,mv88e6190"	: Switch has base address 0x00. Use with models:
+			  6190, 6190X, 6191, 6290, 6390, 6390X
+- "marvell,mv88e6250"	: Switch has base address 0x08 or 0x18. Use with model:
+			  6220, 6250
+
+Required properties:
+- compatible		: Should be one of "marvell,mv88e6085",
+			  "marvell,mv88e6190" or "marvell,mv88e6250" as
+			  indicated above
+- reg			: Address on the MII bus for the switch.
+
+Optional properties:
+
+- reset-gpios		: Should be a gpio specifier for a reset line
+- interrupts		: Interrupt from the switch
+- interrupt-controller	: Indicates the switch is itself an interrupt
+			  controller. This is used for the PHY interrupts.
+#interrupt-cells = <2>	: Controller uses two cells, number and flag
+- eeprom-length		: Set to the length of an EEPROM connected to the
+			  switch. Must be set if the switch can not detect
+			  the presence and/or size of a connected EEPROM,
+			  otherwise optional.
+- mdio			: Container of PHY and devices on the switches MDIO
+			  bus.
+- mdio?		: Container of PHYs and devices on the external MDIO
+			  bus. The node must contains a compatible string of
+			  "marvell,mv88e6xxx-mdio-external"
+
+Example:
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		switch0: switch@0 {
+			compatible = "marvell,mv88e6085";
+			reg = <0>;
+			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				switch1phy0: switch1phy0@0 {
+					reg = <0>;
+					interrupt-parent = <&switch0>;
+					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				};
+			};
+		};
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		switch0: switch@0 {
+			compatible = "marvell,mv88e6390";
+			reg = <0>;
+			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				switch1phy0: switch1phy0@0 {
+					reg = <0>;
+					interrupt-parent = <&switch0>;
+					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				};
+			};
+
+			mdio1 {
+				compatible = "marvell,mv88e6xxx-mdio-external";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				switch1phy9: switch1phy0@9 {
+					reg = <9>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt
new file mode 100644
index 000000000..560369efa
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt
@@ -0,0 +1,315 @@
+Mediatek MT7530 Ethernet switch
+================================
+
+Required properties:
+
+- compatible: may be compatible = "mediatek,mt7530"
+	or compatible = "mediatek,mt7621"
+	or compatible = "mediatek,mt7531"
+- #address-cells: Must be 1.
+- #size-cells: Must be 0.
+- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
+	on multi-chip module belong to MT7623A has or the remotely standalone
+	chip as the function MT7623N reference board provided for.
+
+If compatible mediatek,mt7530 is set then the following properties are required
+
+- core-supply: Phandle to the regulator node necessary for the core power.
+- io-supply: Phandle to the regulator node necessary for the I/O power.
+	See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt
+	for details for the regulator setup on these boards.
+
+If the property mediatek,mcm isn't defined, following property is required
+
+- reset-gpios: Should be a gpio specifier for a reset line.
+
+Else, following properties are required
+
+- resets : Phandle pointing to the system reset controller with
+	line index for the ethsys.
+- reset-names : Should be set to "mcm".
+
+Required properties for the child nodes within ports container:
+
+- reg: Port address described must be 6 for CPU port and from 0 to 5 for
+	user ports.
+- phy-mode: String, the following values are acceptable for port labeled
+	"cpu":
+	If compatible mediatek,mt7530 or mediatek,mt7621 is set,
+	must be either "trgmii" or "rgmii"
+	If compatible mediatek,mt7531 is set,
+	must be either "sgmii", "1000base-x" or "2500base-x"
+
+Port 5 of mt7530 and mt7621 switch is muxed between:
+1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
+   of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+   Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
+	 GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+	 connected to external component!
+
+Port 5 modes/configurations:
+1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
+   GMAC of the SOC.
+   In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
+   GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
+2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+   It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
+   and RGMII delay.
+3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+   Port 5 becomes an extra switch port.
+   Only works on platform where external phy TX<->RX lines are swapped.
+   Like in the Ubiquiti ER-X-SFP.
+4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
+   Currently a 2nd CPU port is not supported by DSA code.
+
+Depending on how the external PHY is wired:
+1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
+   a ethernet port. But can't interface to the 2nd GMAC.
+
+Based on the DT the port 5 mode is configured.
+
+Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+phy-mode must be set, see also example 2 below!
+ * mt7621: phy-mode = "rgmii-txid";
+ * mt7623: phy-mode = "rgmii";
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required, optional properties and how the integrated switch subnodes must
+be specified.
+
+Example:
+
+	&mdio0 {
+		switch@0 {
+			compatible = "mediatek,mt7530";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			core-supply = <&mt6323_vpa_reg>;
+			io-supply = <&mt6323_vemc3v3_reg>;
+			reset-gpios = <&pio 33 0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "wan";
+				};
+
+				port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "trgmii";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "rgmii-txid";
+		phy-handle = <&phy4>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Internal phy */
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+*/
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
+
+&eth {
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy */
+		ephy5: ethernet-phy@7 {
+			reg = <7>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan5";
+					phy-mode = "rgmii";
+					phy-handle = <&ephy5>;
+				};
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
new file mode 100644
index 000000000..7a271d070
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
@@ -0,0 +1,213 @@
+Microchip Ocelot switch driver family
+=====================================
+
+Felix
+-----
+
+Currently the switches supported by the felix driver are:
+
+- VSC9959 (Felix)
+- VSC9953 (Seville)
+
+The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the
+larger ENETC root complex. As a result, the ethernet-switch node is a sub-node
+of the PCIe root complex node and its "reg" property conforms to the parent
+node bindings:
+
+* reg: Specifies PCIe Device Number and Function Number of the endpoint device,
+  in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0).
+
+It does not require a "compatible" string.
+
+The interrupt line is used to signal availability of PTP TX timestamps and for
+TSN frame preemption.
+
+For the external switch ports, depending on board configuration, "phy-mode" and
+"phy-handle" are populated by board specific device tree instances. Ports 4 and
+5 are fixed as internal ports in the NXP LS1028A instantiation.
+
+The CPU port property ("ethernet") configures the feature called "NPI port" in
+the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are
+connected, in the Node Processor Interface (NPI) mode, to an Ethernet port.
+By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal
+2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific
+use case.  Moving the NPI port to an external switch port is hardware possible,
+but there is no platform support for the Linux system on the LS1028A chip to
+operate as an entire slave DSA chip.  NPI functionality (and therefore DSA
+tagging) is supported on a single port at a time.
+
+Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled
+by default, and should be enabled on a per-board basis). But if any external
+switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as
+well, regardless of whether it is configured as the DSA master or not. This is
+because the Felix PHYLINK implementation accesses the MAC PCS registers, which
+in hardware truly belong to the ENETC port #2 and not to Felix.
+
+Supported PHY interface types (appropriate SerDes protocol setting changes are
+needed in the RCW binary):
+
+* phy_mode = "internal": on ports 4 and 5
+* phy_mode = "sgmii": on ports 0, 1, 2, 3
+* phy_mode = "qsgmii": on ports 0, 1, 2, 3
+* phy_mode = "usxgmii": on ports 0, 1, 2, 3
+* phy_mode = "2500base-x": on ports 0, 1, 2, 3
+
+For the rest of the device tree binding definitions, which are standard DSA and
+PCI, refer to the following documents:
+
+Documentation/devicetree/bindings/net/dsa/dsa.txt
+Documentation/devicetree/bindings/pci/pci.txt
+
+Example:
+
+&soc {
+	pcie@1f0000000 { /* Integrated Endpoint Root Complex */
+		ethernet-switch@0,5 {
+			reg = <0x000500 0 0 0 0>;
+			/* IEP INT_B */
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* External ports */
+				port@0 {
+					reg = <0>;
+					label = "swp0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "swp1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "swp2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "swp3";
+				};
+
+				/* Tagging CPU port */
+				port@4 {
+					reg = <4>;
+					ethernet = <&enetc_port2>;
+					phy-mode = "internal";
+
+					fixed-link {
+						speed = <2500>;
+						full-duplex;
+					};
+				};
+
+				/* Non-tagging CPU port */
+				port@5 {
+					reg = <5>;
+					phy-mode = "internal";
+					status = "disabled";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
+};
+
+The VSC9953 switch is found inside NXP T1040. It is a platform device with the
+following required properties:
+
+- compatible:
+	Must be "mscc,vsc9953-switch".
+
+Supported PHY interface types (appropriate SerDes protocol setting changes are
+needed in the RCW binary):
+
+* phy_mode = "internal": on ports 8 and 9
+* phy_mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7
+* phy_mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7
+
+Example:
+
+&soc {
+	ethernet-switch@800000 {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		compatible = "mscc,vsc9953-switch";
+		little-endian;
+		reg = <0x800000 0x290000>;
+
+		ports {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+
+			port@0 {
+				reg = <0x0>;
+				label = "swp0";
+			};
+
+			port@1 {
+				reg = <0x1>;
+				label = "swp1";
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "swp2";
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "swp3";
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "swp4";
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "swp5";
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "swp6";
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "swp7";
+			};
+
+			port@8 {
+				reg = <0x8>;
+				phy-mode = "internal";
+				ethernet = <&enet0>;
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
+			};
+
+			port@9 {
+				reg = <0x9>;
+				phy-mode = "internal";
+				status = "disabled";
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
new file mode 100644
index 000000000..ccbc6d893
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -0,0 +1,175 @@
+* Qualcomm Atheros QCA8xxx switch family
+
+Required properties:
+
+- compatible: should be one of:
+    "qca,qca8334"
+    "qca,qca8337"
+
+- #size-cells: must be 0
+- #address-cells: must be 1
+
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
+mdio-bus each subnode describing a port needs to have a valid phandle
+referencing the internal PHY it is connected to. This is because there's no
+N:N mapping of port and PHY id.
+
+Don't use mixed external and internal mdio-bus configurations, as this is
+not supported by the hardware.
+
+The CPU port of this switch is always port 0.
+
+A CPU port node has the following optional node:
+
+- fixed-link            : Fixed-link subnode describing a link to a non-MDIO
+                          managed entity. See
+                          Documentation/devicetree/bindings/net/fixed-link.txt
+                          for details.
+
+For QCA8K the 'fixed-link' sub-node supports only the following properties:
+
+- 'speed' (integer, mandatory), to indicate the link speed. Accepted
+  values are 10, 100 and 1000
+- 'full-duplex' (boolean, optional), to indicate that full duplex is
+  used. When absent, half duplex is assumed.
+
+Examples:
+
+for the external mdio-bus configuration:
+
+	&mdio0 {
+		phy_port1: phy@0 {
+			reg = <0>;
+		};
+
+		phy_port2: phy@1 {
+			reg = <1>;
+		};
+
+		phy_port3: phy@2 {
+			reg = <2>;
+		};
+
+		phy_port4: phy@3 {
+			reg = <3>;
+		};
+
+		phy_port5: phy@4 {
+			reg = <4>;
+		};
+
+		switch@10 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+					fixed-link {
+						speed = 1000;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+					phy-handle = <&phy_port1>;
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+					phy-handle = <&phy_port2>;
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+					phy-handle = <&phy_port3>;
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+					phy-handle = <&phy_port4>;
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "wan";
+					phy-handle = <&phy_port5>;
+				};
+			};
+		};
+	};
+
+for the internal master mdio-bus configuration:
+
+	&mdio0 {
+		switch@10 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+					fixed-link {
+						speed = 1000;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "wan";
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
new file mode 100644
index 000000000..b6ae8541b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
@@ -0,0 +1,153 @@
+Realtek SMI-based Switches
+==========================
+
+The SMI "Simple Management Interface" is a two-wire protocol using
+bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
+not use the MDIO protocol. This binding defines how to specify the
+SMI-based Realtek devices.
+
+Required properties:
+
+- compatible: must be exactly one of:
+      "realtek,rtl8366"
+      "realtek,rtl8366rb" (4+1 ports)
+      "realtek,rtl8366s"  (4+1 ports)
+      "realtek,rtl8367"
+      "realtek,rtl8367b"
+      "realtek,rtl8368s"  (8 port)
+      "realtek,rtl8369"
+      "realtek,rtl8370"   (8 port)
+
+Required properties:
+- mdc-gpios: GPIO line for the MDC clock line.
+- mdio-gpios: GPIO line for the MDIO data line.
+- reset-gpios: GPIO line for the reset signal.
+
+Optional properties:
+- realtek,disable-leds: if the LED drivers are not used in the
+  hardware design this will disable them so they are not turned on
+  and wasting power.
+
+Required subnodes:
+
+- interrupt-controller
+
+  This defines an interrupt controller with an IRQ line (typically
+  a GPIO) that will demultiplex and handle the interrupt from the single
+  interrupt line coming out of one of the SMI-based chips. It most
+  importantly provides link up/down interrupts to the PHY blocks inside
+  the ASIC.
+
+Required properties of interrupt-controller:
+
+- interrupt: parent interrupt, see interrupt-controller/interrupts.txt
+- interrupt-controller: see interrupt-controller/interrupts.txt
+- #address-cells: should be <0>
+- #interrupt-cells: should be <1>
+
+- mdio
+
+  This defines the internal MDIO bus of the SMI device, mostly for the
+  purpose of being able to hook the interrupts to the right PHY and
+  the right PHY to the corresponding port.
+
+Required properties of mdio:
+
+- compatible: should be set to "realtek,smi-mdio" for all SMI devices
+
+See net/mdio.txt for additional MDIO bus properties.
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+switch {
+	compatible = "realtek,rtl8366rb";
+	/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+	mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+	mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+	reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+
+	switch_intc: interrupt-controller {
+		/* GPIO 15 provides the interrupt */
+		interrupt-parent = <&gpio0>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+	};
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+		port@0 {
+			reg = <0>;
+			label = "lan0";
+			phy-handle = <&phy0>;
+		};
+		port@1 {
+			reg = <1>;
+			label = "lan1";
+			phy-handle = <&phy1>;
+		};
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+			phy-handle = <&phy2>;
+		};
+		port@3 {
+			reg = <3>;
+			label = "lan3";
+			phy-handle = <&phy3>;
+		};
+		port@4 {
+			reg = <4>;
+			label = "wan";
+			phy-handle = <&phy4>;
+		};
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+
+	mdio {
+		compatible = "realtek,smi-mdio", "dsa-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: phy@0 {
+			reg = <0>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <0>;
+		};
+		phy1: phy@1 {
+			reg = <1>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <1>;
+		};
+		phy2: phy@2 {
+			reg = <2>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <2>;
+		};
+		phy3: phy@3 {
+			reg = <3>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <3>;
+		};
+		phy4: phy@4 {
+			reg = <4>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <12>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/sja1105.txt b/Documentation/devicetree/bindings/net/dsa/sja1105.txt
new file mode 100644
index 000000000..13fd21074
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/sja1105.txt
@@ -0,0 +1,156 @@
+NXP SJA1105 switch driver
+=========================
+
+Required properties:
+
+- compatible:
+	Must be one of:
+	- "nxp,sja1105e"
+	- "nxp,sja1105t"
+	- "nxp,sja1105p"
+	- "nxp,sja1105q"
+	- "nxp,sja1105r"
+	- "nxp,sja1105s"
+
+	Although the device ID could be detected at runtime, explicit bindings
+	are required in order to be able to statically check their validity.
+	For example, SGMII can only be specified on port 4 of R and S devices,
+	and the non-SGMII devices, while pin-compatible, are not equal in terms
+	of support for RGMII internal delays (supported on P/Q/R/S, but not on
+	E/T).
+
+Optional properties:
+
+- sja1105,role-mac:
+- sja1105,role-phy:
+	Boolean properties that can be assigned under each port node. By
+	default (unless otherwise specified) a port is configured as MAC if it
+	is driving a PHY (phy-handle is present) or as PHY if it is PHY-less
+	(fixed-link specified, presumably because it is connected to a MAC).
+	The effect of this property (in either its implicit or explicit form)
+	is:
+	- In the case of MII or RMII it specifies whether the SJA1105 port is a
+	  clock source or sink for this interface (not applicable for RGMII
+	  where there is a Tx and an Rx clock).
+	- In the case of RGMII it affects the behavior regarding internal
+	  delays:
+	  1. If sja1105,role-mac is specified, and the phy-mode property is one
+	     of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity
+	     designated to apply the delay/clock skew necessary for RGMII
+	     is the PHY. The SJA1105 MAC does not apply any internal delays.
+	  2. If sja1105,role-phy is specified, and the phy-mode property is one
+	     of the above, the designated entity to apply the internal delays
+	     is the SJA1105 MAC (if hardware-supported). This is only supported
+	     by the second-generation (P/Q/R/S) hardware. On a first-generation
+	     E or T device, it is an error to specify an RGMII phy-mode other
+	     than "rgmii" for a port that is in fixed-link mode. In that case,
+	     the clock skew must either be added by the MAC at the other end of
+	     the fixed-link, or by PCB serpentine traces on the board.
+	These properties are required, for example, in the case where SJA1105
+	ports are at both ends of a MII/RMII PHY-less setup. One end would need
+	to have sja1105,role-mac, while the other sja1105,role-phy.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard
+DSA required and optional properties.
+
+Other observations
+------------------
+
+The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least
+one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
+cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
+depends on the SPI bus master driver.
+
+Example
+-------
+
+Ethernet switch connected via SPI to the host, CPU port wired to enet2:
+
+arch/arm/boot/dts/ls1021a-tsn.dts:
+
+/* SPI controller of the LS1021 */
+&dspi0 {
+	sja1105@1 {
+		reg = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "nxp,sja1105t";
+		spi-max-frequency = <4000000>;
+		fsl,spi-cs-sck-delay = <1000>;
+		fsl,spi-sck-cs-delay = <1000>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				/* ETH5 written on chassis */
+				label = "swp5";
+				phy-handle = <&rgmii_phy6>;
+				phy-mode = "rgmii-id";
+				reg = <0>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@1 {
+				/* ETH2 written on chassis */
+				label = "swp2";
+				phy-handle = <&rgmii_phy3>;
+				phy-mode = "rgmii-id";
+				reg = <1>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@2 {
+				/* ETH3 written on chassis */
+				label = "swp3";
+				phy-handle = <&rgmii_phy4>;
+				phy-mode = "rgmii-id";
+				reg = <2>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@3 {
+				/* ETH4 written on chassis */
+				phy-handle = <&rgmii_phy5>;
+				label = "swp4";
+				phy-mode = "rgmii-id";
+				reg = <3>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@4 {
+				/* Internal port connected to eth2 */
+				ethernet = <&enet2>;
+				phy-mode = "rgmii";
+				reg = <4>;
+				/* Implicit "sja1105,role-phy;" */
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+/* MDIO controller of the LS1021 */
+&mdio0 {
+	/* BCM5464 */
+	rgmii_phy3: ethernet-phy@3 {
+		reg = <0x3>;
+	};
+	rgmii_phy4: ethernet-phy@4 {
+		reg = <0x4>;
+	};
+	rgmii_phy5: ethernet-phy@5 {
+		reg = <0x5>;
+	};
+	rgmii_phy6: ethernet-phy@6 {
+		reg = <0x6>;
+	};
+};
+
+/* Ethernet master port of the LS1021 */
+&enet2 {
+	phy-connection-type = "rgmii";
+	status = "ok";
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt
new file mode 100644
index 000000000..bbf4a13f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt
@@ -0,0 +1,131 @@
+Vitesse VSC73xx Switches
+========================
+
+This defines device tree bindings for the Vitesse VSC73xx switch chips.
+The Vitesse company has been acquired by Microsemi and Microsemi has
+been acquired Microchip but retains this vendor branding.
+
+The currently supported switch chips are:
+Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
+
+This switch could have two different management interface.
+
+If SPI interface is used, the device tree node is an SPI device so it must
+reside inside a SPI bus device tree node, see spi/spi-bus.txt
+
+When the chip is connected to a parallel memory bus and work in memory-mapped
+I/O mode, a platform device is used to represent the vsc73xx. In this case it
+must reside inside a platform bus device tree node.
+
+Required properties:
+
+- compatible: must be exactly one of:
+	"vitesse,vsc7385"
+	"vitesse,vsc7388"
+	"vitesse,vsc7395"
+	"vitesse,vsc7398"
+- gpio-controller: indicates that this switch is also a GPIO controller,
+  see gpio/gpio.txt
+- #gpio-cells: this must be set to <2> and indicates that we are a twocell
+  GPIO controller, see gpio/gpio.txt
+
+Optional properties:
+
+- reset-gpios: a handle to a GPIO line that can issue reset of the chip.
+  It should be tagged as active low.
+
+Required subnodes:
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+SPI:
+switch@0 {
+	compatible = "vitesse,vsc7395";
+	reg = <0>;
+	/* Specified for 2.5 MHz or below */
+	spi-max-frequency = <2500000>;
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+		};
+		vsc: port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac1>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+Platform:
+switch@2,0 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "vitesse,vsc7385";
+	reg = <0x2 0x0 0x20000>;
+	reset-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+		};
+		vsc: port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&enet0>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+
+};