Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

10 files changed, 468 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt
new file mode 100644
index 000000000..c9b35251b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt
@@ -0,0 +1,84 @@
+* Marvell International Ltd. NCI NFC Controller
+
+Required properties:
+- compatible: Should be:
+  - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices
+  - "marvell,nfc-i2c" for I2C devices
+  - "marvell,nfc-spi" for SPI devices
+
+Optional SoC specific properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- reset-n-io: Output GPIO pin used to reset the chip (active low).
+- hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
+
+Optional UART-based chip specific properties:
+- flow-control: Specifies that the chip is using RTS/CTS.
+- break-control: Specifies that the chip needs specific break management.
+
+Optional I2C-based chip specific properties:
+- i2c-int-falling: Specifies that the chip read event shall be trigged on
+  		   falling edge.
+- i2c-int-rising: Specifies that the chip read event shall be trigged on
+  		  rising edge.
+
+Example (for ARM-based BeagleBoard Black with 88W8887 on UART5):
+
+&uart5 {
+
+	nfcmrvluart: nfcmrvluart@5 {
+		compatible = "marvell,nfc-uart";
+
+		reset-n-io = <&gpio3 16 0>;
+
+		hci-muxed;
+		flow-control;
+        }
+};
+
+
+Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1):
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	nfcmrvli2c0: i2c@1 {
+		compatible = "marvell,nfc-i2c";
+
+		reg = <0x8>;
+
+		/* I2C INT configuration */
+		interrupt-parent = <&gpio3>;
+		interrupts = <21 0>;
+
+		/* I2C INT trigger configuration */
+		i2c-int-rising;
+
+		/* Reset IO */
+		reset-n-io = <&gpio3 19 0>;
+	};
+};
+
+
+Example (for ARM-based BeagleBoard Black on SPI0):
+
+&spi0 {
+
+	mrvlnfcspi0: spi@0 {
+		compatible = "marvell,nfc-spi";
+
+		reg = <0>;
+
+		/* SPI Bus configuration */
+		spi-max-frequency = <3000000>;
+		spi-cpha;
+		spi-cpol;
+
+		/* SPI INT configuration */
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 0>;
+
+		/* Reset IO */
+       		reset-n-io = <&gpio3 19 0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt
new file mode 100644
index 000000000..9e4dc510a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt
@@ -0,0 +1,33 @@
+* NXP Semiconductors NXP NCI NFC Controllers
+
+Required properties:
+- compatible: Should be "nxp,nxp-nci-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupts: GPIO interrupt to which the chip is connected
+- enable-gpios: Output GPIO pin used for enabling/disabling the chip
+- firmware-gpios: Output GPIO pin used to enter firmware download mode
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2):
+
+&i2c2 {
+
+
+	npc100: npc100@29 {
+
+		compatible = "nxp,nxp-nci-i2c";
+
+		reg = <0x29>;
+		clock-frequency = <100000>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <29 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/pn532.txt b/Documentation/devicetree/bindings/net/nfc/pn532.txt
new file mode 100644
index 000000000..a5507dc49
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/pn532.txt
@@ -0,0 +1,46 @@
+* NXP Semiconductors PN532 NFC Controller
+
+Required properties:
+- compatible: Should be
+    - "nxp,pn532" Place a node with this inside the devicetree node of the bus
+                  where the NFC chip is connected to.
+                  Currently the kernel has phy bindings for uart and i2c.
+    - "nxp,pn532-i2c" (DEPRECATED) only works for the i2c binding.
+    - "nxp,pn533-i2c" (DEPRECATED) only works for the i2c binding.
+
+Required properties if connected on i2c:
+- clock-frequency: I²C work frequency.
+- reg: for the I²C bus address. This is fixed at 0x24 for the PN532.
+- interrupts: GPIO interrupt to which the chip is connected
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBone with PN532 on I2C2):
+
+&i2c2 {
+
+
+	pn532: nfc@24 {
+
+		compatible = "nxp,pn532";
+
+		reg = <0x24>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
+
+	};
+};
+
+Example (for PN532 connected via uart):
+
+uart4: serial@49042000 {
+        compatible = "ti,omap3-uart";
+
+        pn532: nfc {
+                compatible = "nxp,pn532";
+        };
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt
new file mode 100644
index 000000000..2bd82562c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt
@@ -0,0 +1,33 @@
+* NXP Semiconductors PN544 NFC Controller
+
+Required properties:
+- compatible: Should be "nxp,pn544-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupts: GPIO interrupt to which the chip is connected
+- enable-gpios: Output GPIO pin used for enabling/disabling the PN544
+- firmware-gpios: Output GPIO pin used to enter firmware download mode
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBone with PN544 on I2C2):
+
+&i2c2 {
+
+
+	pn544: pn544@28 {
+
+		compatible = "nxp,pn544-i2c";
+
+		reg = <0x28>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml b/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml
new file mode 100644
index 000000000..cb0b8a560
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/nfc/samsung,s3fwrn5.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S3FWRN5 NCI NFC Controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+  - Krzysztof Opasiak <k.opasiak@samsung.com>
+
+properties:
+  compatible:
+    const: samsung,s3fwrn5-i2c
+
+  en-gpios:
+    maxItems: 1
+    description:
+      Output GPIO pin used for enabling/disabling the chip
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  wake-gpios:
+    maxItems: 1
+    description:
+      Output GPIO pin used to enter firmware mode and sleep/wakeup control
+
+  s3fwrn5,en-gpios:
+    maxItems: 1
+    deprecated: true
+    description:
+      Use en-gpios
+
+  s3fwrn5,fw-gpios:
+    maxItems: 1
+    deprecated: true
+    description:
+      Use wake-gpios
+
+additionalProperties: false
+
+required:
+  - compatible
+  - en-gpios
+  - interrupts
+  - reg
+  - wake-gpios
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c4 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        s3fwrn5@27 {
+            compatible = "samsung,s3fwrn5-i2c";
+            reg = <0x27>;
+
+            interrupt-parent = <&gpa1>;
+            interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+
+            en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>;
+            wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt
new file mode 100644
index 000000000..baa8f8133
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt
@@ -0,0 +1,38 @@
+* STMicroelectronics SAS. ST NCI NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfcb-i2c" or "st,st21nfcc-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupts: GPIO interrupt to which the chip is connected
+- reset-gpios: Output GPIO pin used to reset the ST21NFCB
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- ese-present: Specifies that an ese is physically connected to the nfc
+controller.
+- uicc-present: Specifies that the uicc swp signal can be physically
+connected to the nfc controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2):
+
+&i2c2 {
+
+
+	st21nfcb: st21nfcb@8 {
+
+		compatible = "st,st21nfcb-i2c";
+
+		reg = <0x08>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+
+		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+
+		ese-present;
+		uicc-present;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt
new file mode 100644
index 000000000..d33343330
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt
@@ -0,0 +1,36 @@
+* STMicroelectronics SAS. ST NCI NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfcb-spi"
+- spi-max-frequency: Maximum SPI frequency (<= 4000000).
+- interrupts: GPIO interrupt to which the chip is connected
+- reset-gpios: Output GPIO pin used to reset the ST21NFCB
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- ese-present: Specifies that an ese is physically connected to the nfc
+controller.
+- uicc-present: Specifies that the uicc swp signal can be physically
+connected to the nfc controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4):
+
+&mcspi4 {
+
+
+	st21nfcb: st21nfcb@0 {
+
+		compatible = "st,st21nfcb-spi";
+
+		clock-frequency = <4000000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+
+		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+
+		ese-present;
+		uicc-present;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt
new file mode 100644
index 000000000..b8bd90f80
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt
@@ -0,0 +1,37 @@
+* STMicroelectronics SAS. ST21NFCA NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfca-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- ese-present: Specifies that an ese is physically connected to the nfc
+controller.
+- uicc-present: Specifies that the uicc swp signal can be physically
+connected to the nfc controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2):
+
+&i2c2 {
+
+
+	st21nfca: st21nfca@1 {
+
+		compatible = "st,st21nfca-i2c";
+
+		reg = <0x01>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+
+		ese-present;
+		uicc-present;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st95hf.txt b/Documentation/devicetree/bindings/net/nfc/st95hf.txt
new file mode 100644
index 000000000..3f373a1e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st95hf.txt
@@ -0,0 +1,45 @@
+* STMicroelectronics : NFC Transceiver ST95HF
+
+ST NFC Transceiver is required to attach with SPI bus.
+ST95HF node should be defined in DT as SPI slave device of SPI
+master with which ST95HF transceiver is physically connected.
+The properties defined below are required to be the part of DT
+to include ST95HF transceiver into the platform.
+
+Required properties:
+===================
+- reg: Address of SPI slave "ST95HF transceiver" on SPI master bus.
+
+- compatible: should be "st,st95hf" for ST95HF NFC transceiver
+
+- spi-max-frequency: Max. operating SPI frequency for ST95HF
+	transceiver.
+
+- enable-gpio: GPIO line to enable ST95HF transceiver.
+
+- interrupts : Standard way to define ST95HF transceiver's out
+	interrupt.
+
+Optional property:
+=================
+- st95hfvin-supply : This is an optional property. It contains a
+	phandle to ST95HF transceiver's regulator supply node in DT.
+
+Example:
+=======
+spi@9840000 {
+	reg = <0x9840000 0x110>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&pio0 4>;
+
+	st95hf@0{
+		reg = <0>;
+		compatible = "st,st95hf";
+		spi-max-frequency = <1000000>;
+		enable-gpio = <&pio4 0>;
+		interrupt-parent = <&pio0>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
new file mode 100644
index 000000000..ba1934b95
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -0,0 +1,43 @@
+* Texas Instruments TRF7970A RFID/NFC/15693 Transceiver
+
+Required properties:
+- compatible: Should be "ti,trf7970a".
+- spi-max-frequency: Maximum SPI frequency (<= 2000000).
+- interrupts: A single interrupt specifier.
+- ti,enable-gpios: One or two GPIO entries used for 'EN' and 'EN2' pins on the
+  TRF7970A. EN2 is optional.
+- vin-supply: Regulator for supply voltage to VIN pin
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- autosuspend-delay: Specify autosuspend delay in milliseconds.
+- irq-status-read-quirk: Specify that the trf7970a being used has the
+  "IRQ Status Read" erratum.
+- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF"
+  erratum.
+- vdd-io-supply: Regulator specifying voltage for vdd-io
+- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz
+
+Example (for ARM-based BeagleBone with TRF7970A on SPI1):
+
+&spi1 {
+
+	nfc@0 {
+		compatible = "ti,trf7970a";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&trf7970a_default>;
+		spi-max-frequency = <2000000>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <14 0>;
+		ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>,
+				  <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&ldo3_reg>;
+		vdd-io-supply = <&ldo2_reg>;
+		autosuspend-delay = <30000>;
+		irq-status-read-quirk;
+		en2-rf-quirk;
+		clock-frequency = <27120000>;
+	};
+};