diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt | |
parent | Initial commit. (diff) | |
download | linux-upstream.tar.xz linux-upstream.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt')
-rw-r--r-- | Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt | 262 |
1 files changed, 262 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt new file mode 100644 index 000000000..f903eb447 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -0,0 +1,262 @@ +One-register-per-pin type device tree based pinctrl driver + +Required properties: +- compatible : "pinctrl-single" or "pinconf-single". + "pinctrl-single" means that pinconf isn't supported. + "pinconf-single" means that generic pinconf is supported. + +- reg : offset and length of the register set for the mux registers + +- #pinctrl-cells : number of cells in addition to the index, set to 1 + for pinctrl-single,pins and 2 for pinctrl-single,bits + +- pinctrl-single,register-width : pinmux register access width in bits + +- pinctrl-single,function-mask : mask of allowed pinmux function bits + in the pinmux register + +Optional properties: +- pinctrl-single,function-off : function off mode for disabled state if + available and same for all registers; if not specified, disabling of + pin functions is ignored + +- pinctrl-single,bit-per-mux : boolean to indicate that one register controls + more than one pin, for which "pinctrl-single,function-mask" property specifies + position mask of pin. + +- pinctrl-single,drive-strength : array of value that are used to configure + drive strength in the pinmux register. They're value of drive strength + current and drive strength mask. + + /* drive strength current, mask */ + pinctrl-single,power-source = <0x30 0xf0>; + +- pinctrl-single,bias-pullup : array of value that are used to configure the + input bias pullup in the pinmux register. + + /* input, enabled pullup bits, disabled pullup bits, mask */ + pinctrl-single,bias-pullup = <0 1 0 1>; + +- pinctrl-single,bias-pulldown : array of value that are used to configure the + input bias pulldown in the pinmux register. + + /* input, enabled pulldown bits, disabled pulldown bits, mask */ + pinctrl-single,bias-pulldown = <2 2 0 2>; + + * Two bits to control input bias pullup and pulldown: User should use + pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means + pullup, and the other one bit means pulldown. + * Three bits to control input bias enable, pullup and pulldown. User should + use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias + enable bit should be included in pullup or pulldown bits. + * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as + pinctrl-single,bias-disable. Because pinctrl single driver could implement + it by calling pulldown, pullup disabled. + +- pinctrl-single,input-schmitt : array of value that are used to configure + input schmitt in the pinmux register. In some silicons, there're two input + schmitt value (rising-edge & falling-edge) in the pinmux register. + + /* input schmitt value, mask */ + pinctrl-single,input-schmitt = <0x30 0x70>; + +- pinctrl-single,input-schmitt-enable : array of value that are used to + configure input schmitt enable or disable in the pinmux register. + + /* input, enable bits, disable bits, mask */ + pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>; + +- pinctrl-single,low-power-mode : array of value that are used to configure + low power mode of this pin. For some silicons, the low power mode will + control the output of the pin when the pad including the pin enter low + power mode. + /* low power mode value, mask */ + pinctrl-single,low-power-mode = <0x288 0x388>; + +- pinctrl-single,gpio-range : list of value that are used to configure a GPIO + range. They're value of subnode phandle, pin base in pinctrl device, pin + number in this range, GPIO function value of this GPIO range. + The number of parameters is depend on #pinctrl-single,gpio-range-cells + property. + + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>; + +- interrupt-controller : standard interrupt controller binding if using + interrupts for wake-up events for example. In this case pinctrl-single + is set up as a chained interrupt controller and the wake-up interrupts + can be requested by the drivers using request_irq(). + +- #interrupt-cells : standard interrupt binding if using interrupts + +This driver assumes that there is only one register for each pin (unless the +pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as +specified in the pinctrl-bindings.txt document in this directory. + +The pin configuration nodes for pinctrl-single are specified as pinctrl +register offset and values using pinctrl-single,pins. Only the bits specified +in pinctrl-single,function-mask are updated. + +When #pinctrl-cells = 1, then setting a pin for a device could be done with: + + pinctrl-single,pins = <0xdc 0x118>; + +Where 0xdc is the offset from the pinctrl register base address for the device +pinctrl register, and 0x118 contains the desired value of the pinctrl register. + +When #pinctrl-cells = 2, then setting a pin for a device could be done with: + + pinctrl-single,pins = <0xdc 0x30 0x07>; + +Where 0x30 is the pin configuration value and 0x07 is the pin mux mode value. +These two values are OR'd together to produce the value stored at offset 0xdc. +See the device example and static board pins example below for more information. + +In case when one register changes more than one pin's mux the +pinctrl-single,bits need to be used which takes three parameters: + + pinctrl-single,bits = <0xdc 0x18 0xff>; + +Where 0xdc is the offset from the pinctrl register base address for the +device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to +be used when applying this change to the register. + + +Optional sub-node: In case some pins could be configured as GPIO in the pinmux +register, those pins could be defined as a GPIO range. This sub-node is required +by pinctrl-single,gpio-range property. + +Required properties in sub-node: +- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in + pinctrl-single,gpio-range property. + + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; + + +Example: + +/* SoC common file */ + +/* first controller instance for pins in core domain */ +pmx_core: pinmux@4a100040 { + compatible = "pinctrl-single"; + reg = <0x4a100040 0x0196>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xffff>; +}; + +/* second controller instance for pins in wkup domain */ +pmx_wkup: pinmux@4a31e040 { + compatible = "pinctrl-single"; + reg = <0x4a31e040 0x0038>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xffff>; +}; + +control_devconf0: pinmux@48002274 { + compatible = "pinctrl-single"; + reg = <0x48002274 4>; /* Single register */ + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,bit-per-mux; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x5F>; +}; + +/* third controller instance for pins in gpio domain */ +pmx_gpio: pinmux@d401e000 { + compatible = "pinconf-single"; + reg = <0xd401e000 0x0330>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <7>; + + /* sparse GPIO range could be supported */ + pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1 + &range 12 1 0 &range 13 29 1 + &range 43 1 0 &range 44 49 1 + &range 94 1 1 &range 96 2 1>; + + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; +}; + + +/* board specific .dts file */ + +&pmx_core { + + /* + * map all board specific static pins enabled by the pinctrl driver + * itself during the boot (or just set them up in the bootloader) + */ + pinctrl-names = "default"; + pinctrl-0 = <&board_pins>; + + board_pins: pinmux_board_pins { + pinctrl-single,pins = < + 0x6c 0xf + 0x6e 0xf + 0x70 0xf + 0x72 0xf + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x208 0 /* UART0_RXD (IOCFG138) */ + 0x20c 0 /* UART0_TXD (IOCFG139) */ + >; + pinctrl-single,bias-pulldown = <0 2 2>; + pinctrl-single,bias-pullup = <0 1 1>; + }; + + /* map uart2 pins */ + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0xd8 0x118 + 0xda 0 + 0xdc 0x118 + 0xde 0 + >; + }; +}; + +&control_devconf0 { + mcbsp1_pins: pinmux_mcbsp1_pins { + pinctrl-single,bits = < + 0x00 0x18 0x18 /* FSR/CLKR signal from FSX/CLKX pin */ + >; + }; + + mcbsp2_clks_pins: pinmux_mcbsp2_clks_pins { + pinctrl-single,bits = < + 0x00 0x40 0x40 /* McBSP2 CLKS from McBSP_CLKS pin */ + >; + }; + +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; |