Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 178 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
new file mode 100644
index 000000000..05ec2a838
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
@@ -0,0 +1,178 @@
+* Freescale QUICC Engine module (QE)
+This represents qe module that is installed on PowerQUICC II Pro.
+
+NOTE:  This is an interim binding; it should be updated to fit
+in with the CPM binding later in this document.
+
+Basically, it is a bus of devices, that could act more or less
+as a complete entity (UCC, USB etc ). All of them should be siblings on
+the "root" qe node, using the common properties from there.
+The description below applies to the qe of MPC8360 and
+more nodes and properties would be extended in the future.
+
+i) Root QE device
+
+Required properties:
+- compatible : should be "fsl,qe";
+- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+- reg : offset and length of the device registers.
+- bus-frequency : the clock frequency for QUICC Engine.
+- fsl,qe-num-riscs: define how many RISC engines the QE has.
+- fsl,qe-snums: This property has to be specified as '/bits/ 8' value,
+  defining the array of serial number (SNUM) values for the virtual
+  threads.
+
+Optional properties:
+- fsl,firmware-phandle:
+    Usage: required only if there is no fsl,qe-firmware child node
+    Value type: <phandle>
+    Definition: Points to a firmware node (see "QE Firmware Node" below)
+        that contains the firmware that should be uploaded for this QE.
+        The compatible property for the firmware node should say,
+        "fsl,qe-firmware".
+
+Recommended properties
+- brg-frequency : the internal clock source frequency for baud-rate
+  generators in Hz.
+
+Deprecated properties
+- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use
+  for the threads. Use fsl,qe-snums instead to not only specify the
+  number of snums, but also their values.
+
+Example:
+     qe@e0100000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	#interrupt-cells = <2>;
+	compatible = "fsl,qe";
+	ranges = <0 e0100000 00100000>;
+	reg = <e0100000 480>;
+	brg-frequency = <0>;
+	bus-frequency = <179A7B00>;
+	fsl,qe-snums = /bits/ 8 <
+		0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D
+		0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89
+		0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9
+		0xD8 0xD9 0xE8 0xE9>;
+     }
+
+* Multi-User RAM (MURAM)
+
+Required properties:
+- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
+- mode : the could be "host" or "slave".
+- ranges : Should be defined as specified in 1) to describe the
+   translation of MURAM addresses.
+- data-only : sub-node which defines the address area under MURAM
+   bus that can be allocated as data/parameter
+
+Example:
+
+     muram@10000 {
+	compatible = "fsl,qe-muram", "fsl,cpm-muram";
+	ranges = <0 00010000 0000c000>;
+
+	data-only@0{
+		compatible = "fsl,qe-muram-data",
+			     "fsl,cpm-muram-data";
+		reg = <0 c000>;
+	};
+     };
+
+* Interrupt Controller (IC)
+
+Required properties:
+- compatible : should be "fsl,qe-ic".
+- reg : Address range of IC register set.
+- interrupts : interrupts generated by the device.
+- interrupt-controller : this device is a interrupt controller.
+
+Example:
+
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <95 2 0 0  94 2 0 0>;
+	};
+
+* Serial Interface Block (SI)
+
+The SI manages the routing of eight TDM lines to the QE block serial drivers
+, the MCC and the UCCs, for receive and transmit.
+
+Required properties:
+- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain
+  "fsl,t1040-qe-si".
+- reg : Address range of SI register set.
+
+Example:
+
+	si1: si@700 {
+		compatible = "fsl,t1040-qe-si";
+		reg = <0x700 0x80>;
+	};
+
+* Serial Interface Block RAM(SIRAM)
+
+store the routing entries of SI
+
+Required properties:
+- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain
+  "fsl,t1040-qe-siram".
+- reg : Address range of SI RAM.
+
+Example:
+
+	siram1: siram@1000 {
+		compatible = "fsl,t1040-qe-siram";
+		reg = <0x1000 0x800>;
+	};
+
+* QE Firmware Node
+
+This node defines a firmware binary that is embedded in the device tree, for
+the purpose of passing the firmware from bootloader to the kernel, or from
+the hypervisor to the guest.
+
+The firmware node itself contains the firmware binary contents, a compatible
+property, and any firmware-specific properties.  The node should be placed
+inside a QE node that needs it.  Doing so eliminates the need for a
+fsl,firmware-phandle property.  Other QE nodes that need the same firmware
+should define an fsl,firmware-phandle property that points to the firmware node
+in the first QE node.
+
+The fsl,firmware property can be specified in the DTS (possibly using incbin)
+or can be inserted by the boot loader at boot time.
+
+Required properties:
+  - compatible
+      Usage: required
+      Value type: <string>
+      Definition: A standard property.  Specify a string that indicates what
+          kind of firmware it is.  For QE, this should be "fsl,qe-firmware".
+
+   - fsl,firmware
+      Usage: required
+      Value type: <prop-encoded-array>, encoded as an array of bytes
+      Definition: A standard property.  This property contains the firmware
+          binary "blob".
+
+Example:
+	qe1@e0080000 {
+		compatible = "fsl,qe";
+		qe_firmware:qe-firmware {
+			compatible = "fsl,qe-firmware";
+			fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...];
+		};
+		...
+	};
+
+	qe2@e0090000 {
+		compatible = "fsl,qe";
+		fsl,firmware-phandle = <&qe_firmware>;
+		...
+	};