diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/imx/ldb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/display/imx/ldb.txt | 147 |
1 files changed, 147 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt new file mode 100644 index 000000000..8e6e7d797 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -0,0 +1,147 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.yaml, and in + Documentation/devicetree/bindings/clock/imx6q-clock.yaml. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain either an of graph link to a panel device node +or a display-timings node that describes the video timings for the connected +LVDS display as well as the fsl,data-mapping and fsl,data-width properties. + +Required properties: + - reg : should be <0> or <1> + - port: Input and output port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. + On i.MX5, the internal two-input-multiplexer is used. Due to hardware + limitations, only one input port (port@[0,1]) can be used for each channel + (lvds-channel@[0,1], respectively). + On i.MX6, there should be four input ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected + to a panel input port. Optionally, the output port can be left out if + display-timings are used instead. + +Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - display-timings : A node that describes the display timings as defined in + Documentation/devicetree/bindings/display/panel/display-timing.txt. + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, + <&clks IMX5_CLK_LDB_DI1_SEL>, + <&clks IMX5_CLK_IPU_DI0_SEL>, + <&clks IMX5_CLK_IPU_DI1_SEL>, + <&clks IMX5_CLK_LDB_DI0_GATE>, + <&clks IMX5_CLK_LDB_DI1_GATE>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + /* Using an of-graph endpoint link to connect the panel */ + lvds-channel@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + port@0 { + reg = <0>; + + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; + + port@2 { + reg = <2>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + /* Using display-timings and fsl,data-mapping/width instead */ + lvds-channel@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port@1 { + reg = <1>; + + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; + }; +}; + +panel: lvds-panel { + /* ... */ + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; +}; |