diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c')
48 files changed, 3343 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt new file mode 100644 index 000000000..5764cbedf --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt @@ -0,0 +1,28 @@ +* Analog Devices AD5820 autofocus coil + +Required Properties: + + - compatible: Must contain one of: + - "adi,ad5820" + - "adi,ad5821" + - "adi,ad5823" + + - reg: I2C slave address + + - VANA-supply: supply of voltage for VANA pin + +Optional properties: + + - enable-gpios : GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal is +active low, a high level on the pin enables the device. + +Example: + + ad5820: coil@c { + compatible = "adi,ad5820"; + reg = <0x0c>; + + VANA-supply = <&vaux4>; + enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>; + }; + diff --git a/Documentation/devicetree/bindings/media/i2c/adp1653.txt b/Documentation/devicetree/bindings/media/i2c/adp1653.txt new file mode 100644 index 000000000..4cce0de40 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adp1653.txt @@ -0,0 +1,38 @@ +* Analog Devices ADP1653 flash LED driver + +Required Properties: + + - compatible: Must contain "adi,adp1653" + + - reg: I2C slave address + + - enable-gpios: Specifier of the GPIO connected to EN pin + +There are two LED outputs available - flash and indicator. One LED is +represented by one child node, nodes need to be named "flash" and "indicator". + +Required properties of the LED child node: +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + +Required properties of the flash LED child node: + +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt +- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + +Example: + + adp1653: led-controller@30 { + compatible = "adi,adp1653"; + reg = <0x30>; + enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */ + + flash { + flash-timeout-us = <500000>; + flash-max-microamp = <320000>; + led-max-microamp = <50000>; + }; + indicator { + led-max-microamp = <17500>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.yaml b/Documentation/devicetree/bindings/media/i2c/adv7180.yaml new file mode 100644 index 000000000..d8c54f9d9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7180.yaml @@ -0,0 +1,183 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/adv7180.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADV7180 analog video decoder family + +maintainers: + - Lars-Peter Clausen <lars@metafoo.de> + +description: + The adv7180 family devices are used to capture analog video to different + digital interfaces like MIPI CSI-2 or parallel video. + +properties: + compatible: + items: + - enum: + - adi,adv7180 + - adi,adv7180cp + - adi,adv7180st + - adi,adv7182 + - adi,adv7280 + - adi,adv7280-m + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + - adi,adv7282 + - adi,adv7282-m + + reg: + maxItems: 1 + + powerdown-gpios: + maxItems: 1 + + port: + type: object + description: + A node containing a single endpoint as doucmented in + Documentation/devicetree/bindings/media/video-interfaces.txt + + ports: + type: object + description: + A node containing input and output port nodes with endpoint definitions + as documented in + Documentation/devicetree/bindings/media/video-interfaces.txt + +additionalProperties: false + +required: + - compatible + - reg + +allOf: + - if: + properties: + compatible: + enum: + - adi,adv7180 + - adi,adv7182 + - adi,adv7280 + - adi,adv7280-m + - adi,adv7281 + - adi,adv7281-m + - adi,adv7281-ma + - adi,adv7282 + - adi,adv7282-m + then: + required: + - port + + - if: + properties: + compatible: + contains: + const: adi,adv7180cp + then: + properties: + ports: + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + port@3: + type: object + description: Output port + + patternProperties: + "^port@[0-2]$": + type: object + description: Input port + + required: + - port@3 + + additionalProperties: false + + required: + - ports + + - if: + properties: + compatible: + contains: + const: adi,adv7180st + then: + properties: + ports: + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + port@6: + type: object + description: Output port + + patternProperties: + "^port@[0-5]$": + type: object + description: Input port + + required: + - port@6 + + additionalProperties: false + + required: + - ports + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep>; + }; + }; + }; + + }; + + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + composite-in@20 { + compatible = "adi,adv7180cp"; + reg = <0x20>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7180_in: endpoint { + remote-endpoint = <&composite_con_in>; + }; + }; + + port@3 { + reg = <3>; + adv7180_out: endpoint { + remote-endpoint = <&vin4_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt new file mode 100644 index 000000000..5653bc242 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt @@ -0,0 +1,48 @@ +* Analog Devices adv7343 video encoder + +The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP +package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite +(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard +definition (SD), enhanced definition (ED), or high definition (HD) video +formats. + +Required Properties : +- compatible: Must be "adi,adv7343" + +Optional Properties : +- adi,power-mode-sleep-mode: on enable the current consumption is reduced to + micro ampere level. All DACs and the internal PLL + circuit are disabled. +- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows + internal PLL 1 circuit to be powered down and the + oversampling to be switched off. +- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6, + 0 = OFF and 1 = ON, Default value when this + property is not specified is <0 0 0 0 0 0>. +- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF + and 1 = ON, Default value when this property is + not specified is <0 0>. + +Example: + +i2c0@1c22000 { + ... + ... + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + adv7343_1: endpoint { + adi,power-mode-sleep-mode; + adi,power-mode-pll-ctrl; + /* Use DAC1..3, DAC6 */ + adi,dac-enable = <1 1 1 0 0 1>; + /* Use SD DAC output 1 */ + adi,sd-dac-enable = <1 0>; + }; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt new file mode 100644 index 000000000..4f91686e5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -0,0 +1,116 @@ +* Analog Devices ADV748X video decoder with HDMI receiver + +The ADV7481 and ADV7482 are multi format video decoders with an integrated +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB +from three input sources HDMI, analog and TTL. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7481" for the ADV7481 + - "adi,adv7482" for the ADV7482 + + - reg: I2C slave addresses + The ADV748x has up to twelve 256-byte maps that can be accessed via the + main I2C ports. Each map has it own I2C address and acts as a standard + slave device on the I2C bus. The main address is mandatory, others are + optional and remain at default values if not specified. + +Optional Properties: + + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or + "intrq3". All interrupts are optional. The "intrq3" interrupt + is only available on the adv7481 + - interrupts: Specify the interrupt lines for the ADV748x + - reg-names : Names of maps with programmable addresses. + It shall contain all maps needing a non-default address. + Possible map names are: + "main", "dpll", "cp", "hdmi", "edid", "repeater", + "infoframe", "cbus", "cec", "sdp", "txa", "txb" + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Name Type Port + --------------------------------------- + AIN0 sink 0 + AIN1 sink 1 + AIN2 sink 2 + AIN3 sink 3 + AIN4 sink 4 + AIN5 sink 5 + AIN6 sink 6 + AIN7 sink 7 + HDMI sink 8 + TTL sink 9 + TXA source 10 + TXB source 11 + +The digital output port nodes, when present, shall contain at least one +endpoint. Each of those endpoints shall contain the data-lanes property as +described in video-interfaces.txt. + +Required source endpoint properties: + - data-lanes: an array of physical data lane indexes + The accepted value(s) for this property depends on which of the two + sources are described. For TXA 1, 2 or 4 data lanes can be described + while for TXB only 1 data lane is valid. See video-interfaces.txt + for detailed description. + +Ports are optional if they are not connected to anything at the hardware level. + +Example: + + video-receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70 0x71 0x72 0x73 0x74 0x75 + 0x60 0x61 0x62 0x63 0x64 0x65>; + reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", + "infoframe", "cbus", "cec", "sdp", "txa", "txb"; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gpio6>; + interrupt-names = "intrq1", "intrq2"; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@a { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@b { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode 100644 index 000000000..b3e688b77 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -0,0 +1,88 @@ +* Analog Devices ADV7604/11/12 video decoder with HDMI receiver + +The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated +HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog +input, and the ADV7611 has one HDMI input and no analog input. The 7612 is +similar to the 7611 but has 2 HDMI inputs. + +These device tree bindings support the ADV7611/12 only at the moment. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7611" for the ADV7611 + - "adi,adv7612" for the ADV7612 + + - reg: I2C slave addresses + The ADV76xx has up to thirteen 256-byte maps that can be accessed via the + main I2C ports. Each map has it own I2C address and acts as a standard + slave device on the I2C bus. The main address is mandatory, others are + optional and revert to defaults if not specified. + + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug + detection pins, one per HDMI input. The active flag indicates the GPIO + level that enables hot-plug detection. + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Port ADV7611 ADV7612 +------------------------------------------------------------ + HDMI 0 0, 1 + Digital output 1 2 + +The digital output port node must contain at least one endpoint. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the device's reset pin. + - default-input: Select which input is selected after reset. + - reg-names : Names of maps with programmable addresses. + It can contain any map needing a non-default address. + Possible maps names are : + "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", + "rep", "edid", "hdmi", "test", "cp", "vdp" + +Optional Endpoint Properties: + + The following three properties are defined in video-interfaces.txt and are + valid for source endpoints only. + + - hsync-active: Horizontal synchronization polarity. Defaults to active low. + - vsync-active: Vertical synchronization polarity. Defaults to active low. + - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. + + If none of hsync-active, vsync-active and pclk-sample is specified the + endpoint will use embedded BT.656 synchronization. + +Example: + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + /* + * The edid page will be accessible @ 0x66 on the I2C bus. All + * other maps will retain their default addresses. + */ + reg = <0x4c>, <0x66>; + reg-names = "main", "edid"; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + + #address-cells = <1>; + #size-cells = <0>; + + default-input = <0>; + + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ak7375.txt b/Documentation/devicetree/bindings/media/i2c/ak7375.txt new file mode 100644 index 000000000..aa3e24b41 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ak7375.txt @@ -0,0 +1,8 @@ +Asahi Kasei Microdevices AK7375 voice coil lens driver + +AK7375 is a camera voice coil lens. + +Mandatory properties: + +- compatible: "asahi-kasei,ak7375" +- reg: I2C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt new file mode 100644 index 000000000..bd896e9f6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt @@ -0,0 +1,46 @@ +* Aptina MT9V111 CMOS sensor +---------------------------- + +The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core +based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). + +The sensor has an active pixel array of 640x480 pixels and can output a number +of image resolution and formats controllable through a simple two-wires +interface. + +Required properties: +-------------------- + +- compatible: shall be "aptina,mt9v111". +- clocks: reference to the system clock input provider. + +Optional properties: +-------------------- + +- enable-gpios: output enable signal, pin name "OE#". Active low. +- standby-gpios: low power state control signal, pin name "STANDBY". + Active high. +- reset-gpios: chip reset signal, pin name "RESET#". Active low. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: +-------- + + &i2c1 { + camera@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + + clocks = <&camera_clk>; + + port { + mt9v111_out: endpoint { + remote-endpoint = <&ceu_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml new file mode 100644 index 000000000..63e5b89d2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/media/i2c/chrontel,ch7322.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Chrontel HDMI-CEC Controller + +maintainers: + - Jeff Chase <jnchase@google.com> + +description: + The Chrontel CH7322 is a discrete HDMI-CEC controller. It is + programmable through I2C and drives a single CEC line. + +properties: + compatible: + const: chrontel,ch7322 + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + description: + Reference to the GPIO connected to the RESET pin, if any. This + pin is active-low. + maxItems: 1 + + standby-gpios: + description: + Reference to the GPIO connected to the OE pin, if any. When low + the device will respond to power status requests with "standby" + if in auto mode. + maxItems: 1 + + # see ../cec.txt + hdmi-phandle: + description: phandle to the HDMI controller + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + ch7322@75 { + compatible = "chrontel,ch7322"; + reg = <0x75>; + interrupts = <47 IRQ_TYPE_EDGE_RISING>; + standby-gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + hdmi-phandle = <&hdmi>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt new file mode 100644 index 000000000..b88dcdd41 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt @@ -0,0 +1,9 @@ +Dongwoon Anatech DW9714 camera voice coil lens driver + +DW9174 is a 10-bit DAC with current sink capability. It is intended +for driving voice coil lenses in camera modules. + +Mandatory properties: + +- compatible: "dongwoon,dw9714" +- reg: I²C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml new file mode 100644 index 000000000..21864ab86 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9768.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dongwoon Anatech DW9768 Voice Coil Motor (VCM) Lens Device Tree Bindings + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Dongwoon DW9768 is a single 10-bit digital-to-analog (DAC) converter + with 100 mA output current sink capability. VCM current is controlled with + a linear mode driver. The DAC is controlled via a 2-wire (I2C-compatible) + serial interface that operates at clock rates up to 1MHz. This chip + integrates Advanced Actuator Control (AAC) technology and is intended for + driving voice coil lenses in camera modules. + +properties: + compatible: + enum: + - dongwoon,dw9768 # for DW9768 VCM + - giantec,gt9769 # for GT9769 VCM + + reg: + maxItems: 1 + + vin-supply: + description: + Definition of the regulator used as Digital I/O voltage supply. + + vdd-supply: + description: + Definition of the regulator used as Digital core voltage supply. + + dongwoon,aac-mode: + description: + Indication of AAC mode select. + $ref: "/schemas/types.yaml#/definitions/uint32" + enum: + - 1 # AAC2 mode(operation time# 0.48 x Tvib) + - 2 # AAC3 mode(operation time# 0.70 x Tvib) + - 3 # AAC4 mode(operation time# 0.75 x Tvib) + - 5 # AAC8 mode(operation time# 1.13 x Tvib) + default: 2 + + dongwoon,aac-timing: + description: + Number of AAC Timing count that controlled by one 6-bit period of + vibration register AACT[5:0], the unit of which is 100 us. + $ref: "/schemas/types.yaml#/definitions/uint32" + default: 0x20 + minimum: 0x00 + maximum: 0x3f + + dongwoon,clock-presc: + description: + Indication of VCM internal clock dividing rate select, as one multiple + factor to calculate VCM ring periodic time Tvib. + $ref: "/schemas/types.yaml#/definitions/uint32" + enum: + - 0 # Dividing Rate - 2 + - 1 # Dividing Rate - 1 + - 2 # Dividing Rate - 1/2 + - 3 # Dividing Rate - 1/4 + - 4 # Dividing Rate - 8 + - 5 # Dividing Rate - 4 + default: 1 + +required: + - compatible + - reg + - vin-supply + - vdd-supply + +additionalProperties: false + +examples: + - | + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dw9768: camera-lens@c { + compatible = "dongwoon,dw9768"; + reg = <0x0c>; + + vin-supply = <&mt6358_vcamio_reg>; + vdd-supply = <&mt6358_vcama2_reg>; + dongwoon,aac-timing = <0x39>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt new file mode 100644 index 000000000..c4701f1ea --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt @@ -0,0 +1,9 @@ +Dongwoon Anatech DW9807 voice coil lens driver + +DW9807 is a 10-bit DAC with current sink capability. It is intended for +controlling voice coil lenses. + +Mandatory properties: + +- compatible: "dongwoon,dw9807-vcm" +- reg: I2C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml new file mode 100644 index 000000000..3dc06c628 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imi,rdacm2x-gmsl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IMI D&D RDACM20 and RDACM21 Automotive Camera Platforms + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> + +description: -| + The IMI D&D RDACM20 and RDACM21 are GMSL-compatible camera designed for + automotive applications. + + The RDACM20 camera module encloses a Maxim Integrated MAX9271 GMSL serializer, + coupled with an OV10635 image sensor and an embedded MCU. Both the MCU and + the image sensor are connected to the serializer local I2C bus and are + accessible by the host SoC by direct addressing. + + The RDACM21 camera module encloses the same serializer, coupled with an + OV10640 image sensor and an OV490 ISP. Only the OV490 ISP is interfaced to + the serializer local I2C bus while the image sensor is not accessible from + the host SoC. + + They both connect to a remote GMSL endpoint through a coaxial cable. + + IMI RDACM20 + +---------------+ +--------------------------------+ + | GMSL | <- Video Stream | <- Video--------\ | + | |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV10635 | + | de-serializer | <- I2C messages -> | \<-->MCU | + +---------------+ +--------------------------------+ + + IMI RDACM21 + +---------------+ +--------------------------------+ + | GMSL | <- Video Stream | <- Video--------\ | + | |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV490 | + | | <- I2C messages -> | | | + | de-serializer | | OV10640 <-------| | + +---------------+ +--------------------------------+ + + Both camera modules serialize video data generated by the embedded camera + sensor on the GMSL serial channel to a remote GMSL de-serializer. They also + receive and transmit I2C messages encapsulated and transmitted on the GMSL + bidirectional control channel. + + All I2C traffic received on the GMSL link not directed to the serializer is + propagated on the local I2C bus to the remote device there connected. All the + I2C traffic generated on the local I2C bus not directed to the serializer is + propagated to the remote de-serializer encapsulated in the GMSL control + channel. + + The RDACM20 and RDACM21 DT node should be a direct child of the GMSL + deserializer's I2C bus corresponding to the GMSL link that the camera is + attached to. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + enum: + - imi,rdacm20 + - imi,rdacm21 + + reg: + description: -| + I2C device addresses, the first to be assigned to the serializer, the + following ones to be assigned to the remote devices. + + For RDACM20 the second entry of the property is assigned to the + OV10635 image sensor and the optional third one to the embedded MCU. + + For RDACM21 the second entry is assigned to the OV490 ISP and the optional + third one ignored. + + minItems: 2 + maxItems: 3 + + port: + type: object + additionalProperties: false + description: -| + Connection to the remote GMSL endpoint are modelled using the OF graph + bindings in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + + The device node contains a single "port" child node with a single + "endpoint" sub-device. + + properties: + endpoint: + type: object + additionalProperties: false + + properties: + remote-endpoint: + description: -| + phandle to the remote GMSL endpoint sub-node in the remote node + port. + maxItems: 1 + + required: + - remote-endpoint + + required: + - endpoint + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + camera@31 { + compatible = "imi,rdacm20"; + reg = <0x31>, <0x41>, <0x51>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + }; + }; + + - | + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + camera@31 { + compatible = "imi,rdacm21"; + reg = <0x31>, <0x41>; + + port { + rdacm21_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.yaml b/Documentation/devicetree/bindings/media/i2c/imx219.yaml new file mode 100644 index 000000000..dfc4d29a4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx219.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imx219.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor + +maintainers: + - Dave Stevenson <dave.stevenson@raspberrypi.com> + +description: |- + The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor + with an active array size of 3280H x 2464V. It is programmable through + I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet. + Image data is sent through MIPI CSI-2, which is configured as either 2 or + 4 data lanes. + +properties: + compatible: + const: sony,imx219 + + reg: + description: I2C device address + maxItems: 1 + + clocks: + maxItems: 1 + + VDIG-supply: + description: + Digital I/O voltage supply, 1.8 volts + + VANA-supply: + description: + Analog voltage supply, 2.8 volts + + VDDL-supply: + description: + Digital core voltage supply, 1.2 volts + + reset-gpios: + description: |- + Reference to the GPIO connected to the xclr pin, if any. + Must be released (set high) after all supplies are applied. + + # See ../video-interfaces.txt for more details + port: + type: object + properties: + endpoint: + type: object + properties: + data-lanes: + description: |- + The sensor supports either two-lane, or four-lane operation. + If this property is omitted four-lane operation is assumed. + For two-lane operation the property must be set to <1 2>. + items: + - const: 1 + - const: 2 + + clock-noncontinuous: + type: boolean + description: |- + MIPI CSI-2 clock is non-continuous if this property is present, + otherwise it's continuous. + + link-frequencies: + $ref: /schemas/types.yaml#/definitions/uint64-array + description: + Allowed data bus frequencies. + + required: + - link-frequencies + +required: + - compatible + - reg + - clocks + - VANA-supply + - VDIG-supply + - VDDL-supply + - port + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + imx219: sensor@10 { + compatible = "sony,imx219"; + reg = <0x10>; + clocks = <&imx219_clk>; + VANA-supply = <&imx219_vana>; /* 2.8v */ + VDIG-supply = <&imx219_vdig>; /* 1.8v */ + VDDL-supply = <&imx219_vddl>; /* 1.2v */ + + port { + imx219_0: endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <456000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/imx290.txt b/Documentation/devicetree/bindings/media/i2c/imx290.txt new file mode 100644 index 000000000..a3cc21410 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx290.txt @@ -0,0 +1,57 @@ +* Sony IMX290 1/2.8-Inch CMOS Image Sensor + +The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with +Square Pixel for Color Cameras. It is programmable through I2C and 4-wire +interfaces. The sensor output is available via CMOS logic parallel SDR output, +Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the +default. No bindings have been defined for the other busses. + +Required Properties: +- compatible: Should be "sony,imx290" +- reg: I2C bus address of the device +- clocks: Reference to the xclk clock. +- clock-names: Should be "xclk". +- clock-frequency: Frequency of the xclk clock in Hz. +- vdddo-supply: Sensor digital IO regulator. +- vdda-supply: Sensor analog regulator. +- vddd-supply: Sensor digital core regulator. + +Optional Properties: +- reset-gpios: Sensor reset GPIO + +The imx290 device node should contain one 'port' child node with +an 'endpoint' subnode. For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Properties on endpoint: +- data-lanes: check ../video-interfaces.txt +- link-frequencies: check ../video-interfaces.txt +- remote-endpoint: check ../video-interfaces.txt + +Example: + &i2c1 { + ... + imx290: camera-sensor@1a { + compatible = "sony,imx290"; + reg = <0x1a>; + + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; + clock-names = "xclk"; + clock-frequency = <37125000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + port { + imx290_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <445500000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt new file mode 100644 index 000000000..02b4e9cd7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt @@ -0,0 +1,59 @@ +Maxim Integrated MAX2175 RF to Bits tuner +----------------------------------------- + +The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with +RF to Bits® front-end designed for software-defined radio solutions. + +Required properties: +-------------------- +- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner. +- clocks: clock specifier. +- port: child port node corresponding to the I2S output, in accordance with + the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The port + node must contain at least one endpoint. + +Optional properties: +-------------------- +- maxim,master : phandle to the master tuner if it is a slave. This + is used to define two tuners in diversity mode + (1 master, 1 slave). By default each tuner is an + individual master. +- maxim,refout-load : load capacitance value (in picofarads) on reference + output drive level. The possible load values are: + 0 (default - refout disabled) + 10 + 20 + 30 + 40 + 60 + 70 +- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used + in this hardware for AM antenna input. + +Example: +-------- + +Board specific DTS file + +/* Fixed XTAL clock node */ +maxim_xtal: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <36864000>; +}; + +/* A tuner device instance under i2c bus */ +max2175_0: tuner@60 { + compatible = "maxim,max2175"; + reg = <0x60>; + clocks = <&maxim_xtal>; + maxim,refout-load = <10>; + + port { + max2175_0_ep: endpoint { + remote-endpoint = <&slave_rx_device>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml new file mode 100644 index 000000000..9ea827092 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml @@ -0,0 +1,366 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated Quad GMSL Deserializer + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> + +description: | + The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia + Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data + lanes. + + In addition to video data, the GMSL links carry a bidirectional control + channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic + not addressed to itself to the other side of the links, where a GMSL + serializer will output it on a local I2C bus. In the other direction all I2C + traffic received over GMSL by the MAX9286 is output on the local I2C bus. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + const: maxim,max9286 + + reg: + description: I2C device address + maxItems: 1 + + poc-supply: + description: Regulator providing Power over Coax to the cameras + maxItems: 1 + + enable-gpios: + description: GPIO connected to the \#PWDN pin with inverted polarity + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + ports: + type: object + description: | + The connections to the MAX9286 GMSL and its endpoint nodes are modelled + using the OF graph bindings in accordance with the video interface + bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + + The following table lists the port number corresponding to each device + port. + + Port Description + ---------------------------------------- + Port 0 GMSL Input 0 + Port 1 GMSL Input 1 + Port 2 GMSL Input 2 + Port 3 GMSL Input 3 + Port 4 CSI-2 Output + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + port@[0-3]: + type: object + properties: + reg: + enum: [ 0, 1, 2, 3 ] + + endpoint: + type: object + + properties: + remote-endpoint: + description: | + phandle to the remote GMSL source endpoint subnode in the + remote node port. + + required: + - remote-endpoint + + required: + - reg + - endpoint + + additionalProperties: false + + port@4: + type: object + properties: + reg: + const: 4 + + endpoint: + type: object + + properties: + remote-endpoint: + description: phandle to the remote CSI-2 sink endpoint. + + data-lanes: + description: array of physical CSI-2 data lane indexes. + + required: + - remote-endpoint + - data-lanes + + required: + - reg + - endpoint + + additionalProperties: false + + required: + - port@4 + + i2c-mux: + type: object + description: | + Each GMSL link is modelled as a child bus of an i2c bus + multiplexer/switch, in accordance with bindings described in + Documentation/devicetree/bindings/i2c/i2c-mux.txt. + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + "^i2c@[0-3]$": + type: object + description: | + Child node of the i2c bus multiplexer which represents a GMSL link. + Each serializer device on the GMSL link remote end is represented with + an i2c-mux child node. The MAX9286 chip supports up to 4 GMSL + channels. + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + reg: + description: The index of the GMSL channel. + maxItems: 1 + + patternProperties: + "^camera@[a-f0-9]+$": + type: object + description: | + The remote camera device, composed by a GMSL serializer and a + connected video source. + + properties: + compatible: + description: The remote device compatible string. + + reg: + minItems: 2 + maxItems: 3 + description: | + The I2C addresses to be assigned to the remote devices through + address reprogramming. The number of entries depends on the + requirements of the currently connected remote device. + + port: + type: object + + properties: + endpoint: + type: object + + properties: + remote-endpoint: + description: phandle to the MAX9286 sink endpoint. + + required: + - remote-endpoint + + additionalProperties: false + + required: + - endpoint + + additionalProperties: false + + required: + - compatible + - reg + - port + + additionalProperties: false + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - ports + - i2c-mux + - gpio-controller + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000>; + + gmsl-deserializer@2c { + compatible = "maxim,max9286"; + reg = <0x2c>; + poc-supply = <&camera_poc_12v>; + enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + max9286_in0: endpoint { + remote-endpoint = <&rdacm20_out0>; + }; + }; + + port@1 { + reg = <1>; + + max9286_in1: endpoint { + remote-endpoint = <&rdacm20_out1>; + }; + }; + + port@2 { + reg = <2>; + + max9286_in2: endpoint { + remote-endpoint = <&rdacm20_out2>; + }; + }; + + port@3 { + reg = <3>; + + max9286_in3: endpoint { + remote-endpoint = <&rdacm20_out3>; + }; + }; + + port@4 { + reg = <4>; + + max9286_out: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + camera@51 { + compatible = "imi,rdacm20"; + reg = <0x51>, <0x61>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + camera@52 { + compatible = "imi,rdacm20"; + reg = <0x52>, <0x62>; + + port { + rdacm20_out1: endpoint { + remote-endpoint = <&max9286_in1>; + }; + }; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + camera@53 { + compatible = "imi,rdacm20"; + reg = <0x53>, <0x63>; + + port { + rdacm20_out2: endpoint { + remote-endpoint = <&max9286_in2>; + }; + }; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + camera@54 { + compatible = "imi,rdacm20"; + reg = <0x54>, <0x64>; + + port { + rdacm20_out3: endpoint { + remote-endpoint = <&max9286_in3>; + }; + }; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt new file mode 100644 index 000000000..060d2b7a5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt @@ -0,0 +1,20 @@ +* Melexis MLX90640 FIR Sensor + +Melexis MLX90640 FIR sensor support which allows recording of thermal data +with 32x24 resolution excluding 2 lines of coefficient data that is used by +userspace to render processed frames. + +Required Properties: + - compatible : Must be "melexis,mlx90640" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + mlx90640@33 { + compatible = "melexis,mlx90640"; + reg = <0x33>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m001.txt b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt new file mode 100644 index 000000000..c920552b0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt @@ -0,0 +1,38 @@ +MT9M001: 1/2-Inch Megapixel Digital Image Sensor + +The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital +image sensor. It is programmable through I2C interface. + +Required Properties: + +- compatible: shall be "onnn,mt9m001". +- clocks: reference to the master clock into sensor + +Optional Properties: + +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. + Active low. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + Active high. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + &i2c1 { + camera-sensor@5d { + compatible = "onnn,mt9m001"; + reg = <0x5d>; + reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + port { + mt9m001_out: endpoint { + remote-endpoint = <&vcap_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt new file mode 100644 index 000000000..d0bed6fa9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -0,0 +1,37 @@ +Micron 1.3Mp CMOS Digital Image Sensor + +The Micron MT9M111 is a CMOS active pixel digital image sensor with an active +array size of 1280H x 1024V. It is programmable through a simple two-wire serial +interface. + +Required Properties: +- compatible: value should be "micron,mt9m111" +- clocks: reference to the master clock. +- clock-names: shall be "mclk". + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Optional endpoint properties: +- pclk-sample: For information see ../video-interfaces.txt. The value is set to + 0 if it isn't specified. + +Example: + + i2c_master { + mt9m111@5d { + compatible = "micron,mt9m111"; + reg = <0x5d>; + clocks = <&mclk>; + clock-names = "mclk"; + + port { + mt9m111_1: endpoint { + remote-endpoint = <&pxa_camera>; + pclk-sample = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt new file mode 100644 index 000000000..cb60443ff --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt @@ -0,0 +1,40 @@ +* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor + +The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with +an active array size of 2592H x 1944V. It is programmable through a simple +two-wire serial interface. + +Required Properties: +- compatible: value should be either one among the following + (a) "aptina,mt9p031" for mt9p031 sensor + (b) "aptina,mt9p031m" for mt9p031m sensor + +- input-clock-frequency: Input clock frequency. + +- pixel-clock-frequency: Pixel clock frequency. + +Optional Properties: +- reset-gpios: Chip reset GPIO + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + mt9p031@5d { + compatible = "aptina,mt9p031"; + reg = <0x5d>; + reset-gpios = <&gpio3 30 0>; + + port { + mt9p031_1: endpoint { + input-clock-frequency = <6000000>; + pixel-clock-frequency = <96000000>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt new file mode 100644 index 000000000..100f0ae43 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -0,0 +1,41 @@ +* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor + +The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with +an active array size of 752H x 480V. It is programmable through a simple +two-wire serial interface. + +Required Properties: + +- compatible: value should be either one among the following + (a) "aptina,mt9v022" for MT9V022 color sensor + (b) "aptina,mt9v022m" for MT9V022 monochrome sensor + (c) "aptina,mt9v024" for MT9V024 color sensor + (d) "aptina,mt9v024m" for MT9V024 monochrome sensor + (e) "aptina,mt9v032" for MT9V032 color sensor + (f) "aptina,mt9v032m" for MT9V032 monochrome sensor + (g) "aptina,mt9v034" for MT9V034 color sensor + (h) "aptina,mt9v034m" for MT9V034 monochrome sensor + +Optional Properties: + +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + mt9v032@5c { + compatible = "aptina,mt9v032"; + reg = <0x5c>; + + port { + mt9v032_out: endpoint { + link-frequencies = /bits/ 64 + <13000000 26600000 27000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt new file mode 100644 index 000000000..10ece8108 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -0,0 +1,66 @@ +SMIA/SMIA++ sensor + +SMIA (Standard Mobile Imaging Architecture) is an image sensor standard +defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension +of that. These definitions are valid for both types of sensors. + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + +The device node should contain a "port" node which may contain one or more +endpoint nodes, in accordance with video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt . + +Mandatory properties +-------------------- + +- compatible: "nokia,smia" +- reg: I2C address (0x10, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor + dependent). +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor +- link-frequencies: List of allowed data link frequencies. An array of + 64-bit elements. + + +Optional properties +------------------- + +- reset-gpios: XSHUTDOWN GPIO +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt +- rotation: Integer property; valid values are 0 (sensor mounted upright) + and 180 (sensor mounted upside down). See + ../video-interfaces.txt . + + +Endpoint node mandatory properties +---------------------------------- + +- data-lanes: <1..n> + + +Example +------- + +&i2c2 { + clock-frequency = <400000>; + + camera-sensor@10 { + compatible = "nokia,smia"; + reg = <0x10>; + reset-gpios = <&gpio3 20 0>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <512>; /* 8 * 64 */ + link-frequencies = /bits/ 64 <199200000 210000000 499200000>; + port { + smiapp_ep: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt new file mode 100644 index 000000000..989ce6cb6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt @@ -0,0 +1,41 @@ +* Omnivision OV2640 CMOS sensor + +The Omnivision OV2640 sensor supports multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB +output formats. + +Required Properties: +- compatible: should be "ovti,ov2640" +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- resetb-gpios: reference to the GPIO connected to the resetb pin, if any. +- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov2640: camera@30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xvclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt new file mode 100644 index 000000000..92989a619 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt @@ -0,0 +1,47 @@ +* OV2659 1/5-Inch 2Mp SOC Camera + +The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of +1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports +multiple resolutions output, such as UXGA, SVGA, 720p. It also can support +YUV422, RGB565/555 or raw RGB output formats. + +Required Properties: +- compatible: Must be "ovti,ov2659" +- reg: I2C slave address +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- link-frequencies: target pixel clock frequency. + +Optional Properties: +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active high with internal pull down resistor. +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active low with internal pull up resistor. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + ov2659@30 { + compatible = "ovti,ov2659"; + reg = <0x30>; + + clocks = <&clk_ov2659 0>; + clock-names = "xvclk"; + + powerdown-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>; + + port { + ov2659_0: endpoint { + remote-endpoint = <&vpfe_ep>; + link-frequencies = /bits/ 64 <70000000>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt new file mode 100644 index 000000000..11e925ed9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt @@ -0,0 +1,46 @@ +* Omnivision OV2680 MIPI CSI-2 sensor + +Required Properties: +- compatible: should be "ovti,ov2680". +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- DOVDD-supply: Digital I/O voltage supply. +- DVDD-supply: Digital core voltage supply. +- AVDD-supply: Analog voltage supply. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the powerdown/reset pin, + if any. This is an active low signal to the OV2680. + +The device node must contain one 'port' child node for its digital output +video port, and this port must have a single endpoint in accordance with + the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0). +- data-lanes: should be set to <1> (one CSI-2 lane supported). + +Example: + +&i2c2 { + ov2680: camera-sensor@36 { + compatible = "ovti,ov2680"; + reg = <0x36>; + clocks = <&osc>; + clock-names = "xvclk"; + reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + DOVDD-supply = <&sw2_reg>; + DVDD-supply = <&sw2_reg>; + AVDD-supply = <®_peri_3p15v>; + + port { + ov2680_to_mipi: endpoint { + remote-endpoint = <&mipi_from_sensor>; + clock-lanes = <0>; + data-lanes = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2685.txt b/Documentation/devicetree/bindings/media/i2c/ov2685.txt new file mode 100644 index 000000000..625c4a8c0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2685.txt @@ -0,0 +1,41 @@ +* Omnivision OV2685 MIPI CSI-2 sensor + +Required Properties: +- compatible: shall be "ovti,ov2685" +- clocks: reference to the xvclk input clock +- clock-names: shall be "xvclk" +- avdd-supply: Analog voltage supply, 2.8 volts +- dovdd-supply: Digital I/O voltage supply, 1.8 volts +- dvdd-supply: Digital core voltage supply, 1.8 volts +- reset-gpios: Low active reset gpio + +The device node shall contain one 'port' child node with an +'endpoint' subnode for its digital output video port, +in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. +The endpoint optional property 'data-lanes' shall be "<1>". + +Example: +&i2c7 { + ov2685: camera-sensor@3c { + compatible = "ovti,ov2685"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cru SCLK_TESTCLKOUT1>; + clock-names = "xvclk"; + + avdd-supply = <&pp2800_cam>; + dovdd-supply = <&pp1800>; + dvdd-supply = <&pp1800>; + reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + + port { + ucam_out: endpoint { + remote-endpoint = <&mipi_in_ucam>; + data-lanes = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt new file mode 100644 index 000000000..c97c2f2da --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -0,0 +1,92 @@ +* Omnivision OV5640 MIPI CSI-2 / parallel sensor + +Required Properties: +- compatible: should be "ovti,ov5640" +- clocks: reference to the xclk input clock. +- clock-names: should be "xclk". +- DOVDD-supply: Digital I/O voltage supply, 1.8 volts +- AVDD-supply: Analog voltage supply, 2.8 volts +- DVDD-supply: Digital core voltage supply, 1.5 volts + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the reset pin, if any. + This is an active low signal to the OV5640. +- powerdown-gpios: reference to the GPIO connected to the powerdown pin, + if any. This is an active high signal to the OV5640. +- rotation: as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt, + valid values are 0 (sensor mounted upright) and 180 (sensor + mounted upside down). + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0) +- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) + +Endpoint node required properties for parallel connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- bus-width: shall be set to <8> for 8 bits parallel bus + or <10> for 10 bits parallel bus +- data-shift: shall be set to <2> for 8 bits parallel bus + (lines 9:2 are used) or <0> for 10 bits parallel bus +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. + +Examples: + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + rotation = <180>; + + port { + /* MIPI CSI-2 bus endpoint */ + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_from_ov5640>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt new file mode 100644 index 000000000..72ad992f7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt @@ -0,0 +1,54 @@ +* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor + +The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with +an active array size of 2592H x 1944V. It is programmable through a serial I2C +interface. + +Required Properties: +- compatible: Value should be "ovti,ov5645". +- clocks: Reference to the xclk clock. +- clock-names: Should be "xclk". +- clock-frequency: Frequency of the xclk clock. +- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds + to the hardware pin PWDNB which is physically active low. +- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to + the hardware pin RESETB. +- vdddo-supply: Chip digital IO regulator. +- vdda-supply: Chip analog regulator. +- vddd-supply: Chip digital core regulator. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + &i2c1 { + ... + + ov5645: ov5645@3c { + compatible = "ovti,ov5645"; + reg = <0x3c>; + + enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&clks 200>; + clock-names = "xclk"; + clock-frequency = <24000000>; + + vdddo-supply = <&camera_dovdd_1v8>; + vdda-supply = <&camera_avdd_2v8>; + vddd-supply = <&camera_dvdd_1v2>; + + port { + ov5645_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&csi0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.yaml b/Documentation/devicetree/bindings/media/i2c/ov5647.yaml new file mode 100644 index 000000000..280c62afa --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5647.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ov5647.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV5647 raw image sensor + +maintainers: + - Dave Stevenson <dave.stevenson@raspberrypi.com> + - Jacopo Mondi <jacopo@jmondi.org> + +description: |- + The OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data + interfaces and CCI (I2C compatible) control bus. + +properties: + compatible: + const: ovti,ov5647 + + reg: + description: I2C device address. + maxItems: 1 + + clocks: + description: Reference to the xclk clock. + maxItems: 1 + + pwdn-gpios: + description: Reference to the GPIO connected to the pwdn pin. Active high. + maxItems: 1 + + port: + type: object + description: |- + Should contain one endpoint sub-node used to model connection to the + video receiver according to the specification defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + + properties: + endpoint: + type: object + + properties: + remote-endpoint: + description: |- + phandle to the video receiver input port. + + clock-noncontinuous: + type: boolean + description: |- + Set to true to allow MIPI CSI-2 non-continuous clock operations. + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov5647: camera@36 { + compatible = "ovti,ov5647"; + reg = <0x36>; + clocks = <&camera_clk>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + port { + camera_out: endpoint { + remote-endpoint = <&csi1_ep1>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/ov5695.txt b/Documentation/devicetree/bindings/media/i2c/ov5695.txt new file mode 100644 index 000000000..640a63717 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5695.txt @@ -0,0 +1,41 @@ +* Omnivision OV5695 MIPI CSI-2 sensor + +Required Properties: +- compatible: shall be "ovti,ov5695" +- clocks: reference to the xvclk input clock +- clock-names: shall be "xvclk" +- avdd-supply: Analog voltage supply, 2.8 volts +- dovdd-supply: Digital I/O voltage supply, 1.8 volts +- dvdd-supply: Digital core voltage supply, 1.2 volts +- reset-gpios: Low active reset gpio + +The device node shall contain one 'port' child node with an +'endpoint' subnode for its digital output video port, +in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. +The endpoint optional property 'data-lanes' shall be "<1 2>". + +Example: +&i2c7 { + ov5695: camera-sensor@36 { + compatible = "ovti,ov5695"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cru SCLK_TESTCLKOUT1>; + clock-names = "xvclk"; + + avdd-supply = <&pp2800_cam>; + dovdd-supply = <&pp1800>; + dvdd-supply = <&pp1250_cam>; + reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt new file mode 100644 index 000000000..8281151f7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7251.txt @@ -0,0 +1,52 @@ +* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor + +The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor +with an active array size of 640H x 480V. It is programmable through a serial +I2C interface. + +Required Properties: +- compatible: Value should be "ovti,ov7251". +- clocks: Reference to the xclk clock. +- clock-names: Should be "xclk". +- clock-frequency: Frequency of the xclk clock. +- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds + to the hardware pin XSHUTDOWN which is physically active low. +- vdddo-supply: Chip digital IO regulator. +- vdda-supply: Chip analog regulator. +- vddd-supply: Chip digital core regulator. + +The device node shall contain one 'port' child node with a single 'endpoint' +subnode for its digital output video port, in accordance with the video +interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + &i2c1 { + ... + + ov7251: camera-sensor@60 { + compatible = "ovti,ov7251"; + reg = <0x60>; + + enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_bw_default>; + + clocks = <&clks 200>; + clock-names = "xclk"; + clock-frequency = <24000000>; + + vdddo-supply = <&camera_dovdd_1v8>; + vdda-supply = <&camera_avdd_2v8>; + vddd-supply = <&camera_dvdd_1v2>; + + port { + ov7251_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0>; + remote-endpoint = <&csi0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7670.txt b/Documentation/devicetree/bindings/media/i2c/ov7670.txt new file mode 100644 index 000000000..2c972a56f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7670.txt @@ -0,0 +1,55 @@ +* Omnivision OV7670 CMOS sensor + +The Omnivision OV7670 sensor supports multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB +output formats. + +Required Properties: +- compatible: should be "ovti,ov7670" +- clocks: reference to the xclk input clock. +- clock-names: should be "xclk". + +Required Endpoint Properties: +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active is low. +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active is high. +- ov7670,pclk-hb-disable: a boolean property to suppress pixel clock output + signal during horizontal blankings. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov7670: camera@21 { + compatible = "ovti,ov7670"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + reset-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + + ov7670,pclk-hb-disable; + + port { + ov7670_0: endpoint { + hsync-active = <0>; + vsync-active = <0>; + + remote-endpoint = <&isi_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt new file mode 100644 index 000000000..0b3ede5b8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov772x.txt @@ -0,0 +1,40 @@ +* Omnivision OV7720/OV7725 CMOS sensor + +The Omnivision OV7720/OV7725 sensor supports multiple resolutions output, +such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can +support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats. + +Required Properties: +- compatible: shall be one of + "ovti,ov7720" + "ovti,ov7725" +- clocks: reference to the xclk input clock. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the RSTB pin which is + active low, if any. +- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is + active high, if any. + +The device node shall contain one 'port' child node with one child 'endpoint' +subnode for its digital output video port, in accordance with the video +interface bindings defined in Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + +&i2c0 { + ov772x: camera@21 { + compatible = "ovti,ov7725"; + reg = <0x21>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>; + clocks = <&xclk>; + + port { + ov772x_0: endpoint { + remote-endpoint = <&vcap1_in0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt new file mode 100644 index 000000000..af781c3a5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt @@ -0,0 +1,47 @@ +* Omnivision OV7740 CMOS image sensor + +The Omnivision OV7740 image sensor supports multiple output image +size, such as VGA, and QVGA, CIF and any size smaller. It also +supports the RAW RGB and YUV output formats. + +The common video interfaces bindings (see video-interfaces.txt) should +be used to specify link to the image data receiver. The OV7740 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Required Properties: +- compatible: "ovti,ov7740". +- reg: I2C slave address of the sensor. +- clocks: Reference to the xvclk input clock. +- clock-names: "xvclk". + +Optional Properties: +- reset-gpios: Rreference to the GPIO connected to the reset_b pin, + if any. Active low with pull-ip resistor. +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin, + if any. Active high with pull-down resistor. + +Endpoint node mandatory properties: +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov8856.yaml b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml new file mode 100644 index 000000000..cde85553f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2019 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ov8856.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Omnivision OV8856 CMOS Sensor Device Tree Bindings + +maintainers: + - Dongchun Zhu <dongchun.zhu@mediatek.com> + +description: |- + The Omnivision OV8856 is a high performance, 1/4-inch, 8 megapixel, CMOS + image sensor that delivers 3264x2448 at 30fps. It provides full-frame, + sub-sampled, and windowed 10-bit MIPI images in various formats via the + Serial Camera Control Bus (SCCB) interface. This chip is programmable + through I2C and two-wire SCCB. The sensor output is available via CSI-2 + serial data output (up to 4-lane). + +properties: + compatible: + const: ovti,ov8856 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: + Input clock for the sensor. + items: + - const: xvclk + + clock-frequency: + description: + Frequency of the xvclk clock in Hertz. + + dovdd-supply: + description: + Definition of the regulator used as interface power supply. + + avdd-supply: + description: + Definition of the regulator used as analog power supply. + + dvdd-supply: + description: + Definition of the regulator used as digital power supply. + + reset-gpios: + description: + The phandle and specifier for the GPIO that controls sensor reset. + This corresponds to the hardware pin XSHUTDOWN which is physically + active low. + + port: + type: object + additionalProperties: false + description: + A node containing an output port node with an endpoint definition + as documented in + Documentation/devicetree/bindings/media/video-interfaces.txt + + properties: + endpoint: + type: object + + properties: + data-lanes: + description: |- + The driver only supports four-lane operation. + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + link-frequencies: + $ref: /schemas/types.yaml#/definitions/uint64-array + description: + Allowed data bus frequencies. 360000000, 180000000 Hz or both + are supported by the driver. + + + required: + - link-frequencies + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - clock-names + - clock-frequency + - dovdd-supply + - avdd-supply + - dvdd-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ov8856: camera@10 { + compatible = "ovti,ov8856"; + reg = <0x10>; + + reset-gpios = <&pio 111 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&clk_24m_cam>; + + clocks = <&cam_osc>; + clock-names = "xvclk"; + clock-frequency = <19200000>; + + avdd-supply = <&mt6358_vcama2_reg>; + dvdd-supply = <&mt6358_vcamd_reg>; + dovdd-supply = <&mt6358_vcamio_reg>; + + port { + wcam_out: endpoint { + remote-endpoint = <&mipi_in_wcam>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + }; + }; + }; + }; +... + diff --git a/Documentation/devicetree/bindings/media/i2c/ov9650.txt b/Documentation/devicetree/bindings/media/i2c/ov9650.txt new file mode 100644 index 000000000..506dfc528 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov9650.txt @@ -0,0 +1,36 @@ +* Omnivision OV9650/OV9652 CMOS sensor + +Required Properties: +- compatible: shall be one of + "ovti,ov9650" + "ovti,ov9652" +- clocks: reference to the xvclk input clock. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active is high. +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active is high. + +The device node shall contain one 'port' child node with one child 'endpoint' +subnode for its digital output video port, in accordance with the video +interface bindings defined in Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + +&i2c0 { + ov9650: camera@30 { + compatible = "ovti,ov9650"; + reg = <0x30>; + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_HIGH>; + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_HIGH>; + clocks = <&xclk>; + + port { + ov9650_0: endpoint { + remote-endpoint = <&vcap1_in0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt new file mode 100644 index 000000000..4a3181a3d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt @@ -0,0 +1,19 @@ +* Panasonic AMG88xx + +The Panasonic family of AMG88xx Grid-Eye sensors allow recording +8x8 10Hz video which consists of thermal datapoints + +Required Properties: + - compatible : Must be "panasonic,amg88xx" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + amg88xx@69 { + compatible = "panasonic,amg88xx"; + reg = <0x69>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt b/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt new file mode 100644 index 000000000..f11f28a5f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt @@ -0,0 +1,53 @@ +* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor + +The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with +an active array size of 4224H x 3200V. It is programmable through an I2C +interface. +Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum +throughput of 1.2Gbps/lane. + + +Required Properties: +- compatible: Shall be "sony,imx214". +- reg: I2C bus address of the device. Depending on how the sensor is wired, + it shall be <0x10> or <0x1a>; +- enable-gpios: GPIO descriptor for the enable pin. +- vdddo-supply: Chip digital IO regulator (1.8V). +- vdda-supply: Chip analog regulator (2.7V). +- vddd-supply: Chip digital core regulator (1.12V). +- clocks: Reference to the xclk clock. +- clock-frequency: Frequency of the xclk clock. + +Optional Properties: +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt + +The imx214 device node shall contain one 'port' child node with +an 'endpoint' subnode. For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Properties on endpoint: +- data-lanes: check ../video-interfaces.txt +- link-frequencies: check ../video-interfaces.txt +- remote-endpoint: check ../video-interfaces.txt + +Example: + + camera-sensor@1a { + compatible = "sony,imx214"; + reg = <0x1a>; + vdddo-supply = <&pm8994_lvs1>; + vddd-supply = <&camera_vddd_1v12>; + vdda-supply = <&pm8994_l17>; + lens-focus = <&ad5820>; + enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; + clocks = <&mmcc CAMSS_MCLK0_CLK>; + clock-frequency = <24000000>; + port { + imx214_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <480000000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml new file mode 100644 index 000000000..f697e1a20 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/sony,imx274.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony 1/2.5-Inch 8.51MP CMOS Digital Image Sensor + +maintainers: + - Leon Luo <leonl@leopardimaging.com> + +description: | + The Sony IMX274 is a 1/2.5-inch CMOS active pixel digital image sensor with an + active array size of 3864H x 2202V. It is programmable through I2C interface. + Image data is sent through MIPI CSI-2, which is configured as 4 lanes at 1440 + Mbps. + +properties: + compatible: + const: sony,imx274 + + reg: + const: 0x1a + + reset-gpios: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: inck + + vana-supply: + description: Sensor 2.8 V analog supply. + maxItems: 1 + + vdig-supply: + description: Sensor 1.8 V digital core supply. + maxItems: 1 + + vddl-supply: + description: Sensor digital IO 1.2 V supply. + maxItems: 1 + + port: + type: object + description: Output video port. See ../video-interfaces.txt. + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + imx274: camera-sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + reset-gpios = <&gpio_sensor 0 0>; + + port { + sensor_out: endpoint { + remote-endpoint = <&csiss_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt new file mode 100644 index 000000000..7976e6c40 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt @@ -0,0 +1,82 @@ +STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge + +MIPID02 has two CSI-2 input ports, only one of those ports can be active at a +time. Active port input stream will be de-serialized and its content outputted +through PARALLEL output port. +CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second +input port is a single lane 800Mbps. Both ports support clock and data lane +polarity swap. First port also supports data lane swap. +PARALLEL output port has a maximum width of 12 bits. +Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444, +YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. + +Required Properties: +- compatible: shall be "st,st-mipid02" +- clocks: reference to the xclk input clock. +- clock-names: shall be "xclk". +- VDDE-supply: sensor digital IO supply. Must be 1.8 volts. +- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the xsdn pin, if any. + This is an active low signal to the mipid02. + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows: + + Port Description + ----------------------------- + 0 CSI-2 first input port + 1 CSI-2 second input port + 2 PARALLEL output + +Endpoint node required property for CSI-2 connection is: +- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be +<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>. +Endpoint node optional property for CSI-2 connection is: +- lane-polarities: any lane can be inverted or not. + +Endpoint node required property for PARALLEL connection is: +- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>. +Endpoint node optional properties for PARALLEL connection are: +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +LOW being the default. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +LOW being the default. + +Example: + +mipid02: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + status = "okay"; + clocks = <&clk_ext_camera_12>; + clock-names = "xclk"; + VDDE-supply = <&vdd>; + VDDIN-supply = <&vdd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + ep0: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&mipi_csi2_in>; + }; + }; + port@2 { + reg = <2>; + + ep2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + remote-endpoint = <¶llel_out>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/Documentation/devicetree/bindings/media/i2c/tc358743.txt new file mode 100644 index 000000000..59102edcf --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tc358743.txt @@ -0,0 +1,48 @@ +* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge + +The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts +a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C. + +Required Properties: + +- compatible: value should be "toshiba,tc358743" +- clocks, clock-names: should contain a phandle link to the reference clock + source, the clock input is named "refclk". + +Optional Properties: + +- reset-gpios: gpio phandle GPIO connected to the reset pin +- interrupts: GPIO connected to the interrupt pin +- data-lanes: should be <1 2 3 4> for four-lane operation, + or <1 2> for two-lane operation +- clock-lanes: should be <0> +- clock-noncontinuous: Presence of this boolean property decides whether the + MIPI CSI-2 clock is continuous or non-continuous. +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. The frequency + is half of the bps per lane due to DDR transmission. + +For further information on the MIPI CSI-2 endpoint node properties, see +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + tc358743@f { + compatible = "toshiba,tc358743"; + reg = <0x0f>; + clocks = <&hdmi_osc>; + clock-names = "refclk"; + reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + port { + tc358743_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2 3 4>; + clock-lanes = <0>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <297000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt new file mode 100644 index 000000000..e76167999 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt @@ -0,0 +1,178 @@ +Device-Tree bindings for the NXP TDA1997x HDMI receiver + +The TDA19971/73 are HDMI video receivers. + +The TDA19971 Video port output pins can be used as follows: + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The TDA19973 Video port output pins can be used as follows: + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The Video port output pins are mapped via 4-bit 'pin groups' allowing +for a variety of connection possibilities including swapping pin order within +pin groups. The video_portcfg device-tree property consists of register mapping +pairs which map a chip-specific VP output register to a 4-bit pin group. If +the pin group needs to be bit-swapped you can use the *_S pin-group defines. + +Required Properties: + - compatible : + - "nxp,tda19971" for the TDA19971 + - "nxp,tda19973" for the TDA19973 + - reg : I2C slave address + - interrupts : The interrupt number + - DOVDD-supply : Digital I/O supply + - DVDD-supply : Digital Core supply + - AVDD-supply : Analog supply + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. + +Optional Properties: + - nxp,audout-format : DAI bus format: "i2s" or "spdif". + - nxp,audout-width : width of audio output data bus (1-4). + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec + mclk. + +The port node shall contain one endpoint child node for its digital +output video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Optional Endpoint Properties: + The following three properties are defined in video-interfaces.txt and + are valid for the output parallel bus endpoint: + - hsync-active: Horizontal synchronization polarity. Defaults to active high. + - vsync-active: Vertical synchronization polarity. Defaults to active high. + - data-active: Data polarity. Defaults to active high. + +Examples: + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over + * 2 pixclk cycles. + */ + nxp,vidout-portcfg = + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >, + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >, + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ths8200.txt new file mode 100644 index 000000000..285f6ae7d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ths8200.txt @@ -0,0 +1,19 @@ +* Texas Instruments THS8200 video encoder + +The ths8200 device is a digital to analog converter used in DVD players, video +recorders, set-top boxes. + +Required Properties : +- compatible : value must be "ti,ths8200" + +Example: + + i2c0@1c22000 { + ... + ... + ths8200@5c { + compatible = "ti,ths8200"; + reg = <0x5c>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt new file mode 100644 index 000000000..e80d5891b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -0,0 +1,55 @@ +Toshiba et8ek8 5MP sensor + +Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "toshiba,et8ek8" +- reg: I2C address (0x3e, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), 2.8 volts +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor. Camera + driver will set this frequency on the external clock. The clock frequency is + a pre-determined frequency known to be suitable to the board. +- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor + is in hardware standby mode when the signal is in the low state. + + +Optional properties +------------------- + +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt + + +Endpoint node mandatory properties +---------------------------------- + +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c3 { + clock-frequency = <400000>; + + cam1: camera@3e { + compatible = "toshiba,et8ek8"; + reg = <0x3e>; + vana-supply = <&vaux4>; + clocks = <&isp 0>; + clock-frequency = <9600000>; + reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */ + port { + csi_cam1: endpoint { + remote-endpoint = <&csi_out1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt new file mode 100644 index 000000000..46752cc71 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt @@ -0,0 +1,44 @@ +* Texas Instruments TVP514x video decoder + +The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip +digital video decoder that digitizes and decodes all popular baseband analog +video formats into digital video component. The tvp514x decoder supports analog- +to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D +conversion and decoding of NTSC, PAL and SECAM composite and S-video into +component YCbCr. + +Required Properties : +- compatible : value should be either one among the following + (a) "ti,tvp5146" for tvp5146 decoder. + (b) "ti,tvp5146m2" for tvp5146m2 decoder. + (c) "ti,tvp5147" for tvp5147 decoder. + (d) "ti,tvp5147m1" for tvp5147m1 decoder. + +- hsync-active: HSYNC Polarity configuration for endpoint. + +- vsync-active: VSYNC Polarity configuration for endpoint. + +- pclk-sample: Clock polarity of the endpoint. + +For further reading on port node refer to Documentation/devicetree/bindings/ +media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp514x@5c { + compatible = "ti,tvp5146"; + reg = <0x5c>; + + port { + tvp514x_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt new file mode 100644 index 000000000..719b2995d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -0,0 +1,157 @@ +* Texas Instruments TVP5150 and TVP5151 video decoders + +The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL +(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV +with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +Required Properties: +==================== +- compatible: Value must be "ti,tvp5150". +- reg: I2C slave address. + +Optional Properties: +==================== +- pdn-gpios: Phandle for the GPIO connected to the PDN pin, if any. +- reset-gpios: Phandle for the GPIO connected to the RESETB pin, if any. + +The device node must contain one 'port' child node per device physical input +and output port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows + + Name Type Port + -------------------------------------- + AIP1A sink 0 + AIP1B sink 1 + Y-OUT src 2 + +The device node must contain at least one sink port and the src port. Each input +port must be linked to an endpoint defined in [1]. The port/connector layout is +as follows + +tvp-5150 port@0 (AIP1A) + endpoint@0 -----------> Comp0-Con port + endpoint@1 ------+----> Svideo-Con port +tvp-5150 port@1 (AIP1B) | + endpoint@1 ------+ + endpoint@0 -----------> Comp1-Con port +tvp-5150 port@2 + endpoint (video bitstream output at YOUT[0-7] parallel bus) + +Required Endpoint Properties for parallel synchronization on output port: +========================================================================= + +- hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH). +- vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH). +- field-even-active: Field signal level during the even field data + transmission. Must be <0>. + +Note: Do not specify any of these properties if you want to use the embedded + BT.656 synchronization. + +Optional Connector Properties: +============================== + +- sdtv-standards: Set the possible signals to which the hardware tries to lock + instead of using the autodetection mechnism. Please look at + [1] for more information. + +[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml. + +Example - three input sources: +#include <dt-bindings/display/sdtv-standards.h> + +comp_connector_0 { + compatible = "composite-video-connector"; + label = "Composite0"; + sdtv-standards = <SDTV_STD_PAL_M>; /* limit to pal-m signals */ + + port { + composite0_to_tvp5150: endpoint { + remote-endpoint = <&tvp5150_to_composite0>; + }; + }; +}; + +comp_connector_1 { + compatible = "composite-video-connector"; + label = "Composite1"; + sdtv-standards = <SDTV_STD_NTSC_M>; /* limit to ntsc-m signals */ + + port { + composite1_to_tvp5150: endpoint { + remote-endpoint = <&tvp5150_to_composite1>; + }; + }; +}; + +svideo_connector { + compatible = "svideo-connector"; + label = "S-Video"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + svideo_luma_to_tvp5150: endpoint@0 { + reg = <0>; + remote-endpoint = <&tvp5150_to_svideo_luma>; + }; + + svideo_chroma_to_tvp5150: endpoint@1 { + reg = <1>; + remote-endpoint = <&tvp5150_to_svideo_chroma>; + }; + }; +}; + +&i2c2 { + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tvp5150_to_composite0: endpoint@0 { + reg = <0>; + remote-endpoint = <&composite0_to_tvp5150>; + }; + + tvp5150_to_svideo_luma: endpoint@1 { + reg = <1>; + remote-endpoint = <&svideo_luma_to_tvp5150>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tvp5150_to_composite1: endpoint@0 { + reg = <0>; + remote-endpoint = <&composite1_to_tvp5150>; + }; + + tvp5150_to_svideo_chroma: endpoint@1 { + reg = <1>; + remote-endpoint = <&svideo_chroma_to_tvp5150>; + }; + }; + + port@2 { + reg = <2>; + + tvp5150_1: endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt new file mode 100644 index 000000000..5f28b5d9a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt @@ -0,0 +1,53 @@ +* Texas Instruments TV7002 video decoder + +The TVP7002 device supports digitizing of video and graphics signal in RGB and +YPbPr color space. + +Required Properties : +- compatible : Must be "ti,tvp7002" + +Optional Properties: +- hsync-active: HSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- vsync-active: VSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- pclk-sample: Clock polarity of the bus. Default value when this property is + not specified is <0>. + +- sync-on-green-active: Active state of Sync-on-green signal property of the + endpoint. + 0 = Normal Operation (Active Low, Default) + 1 = Inverted operation + +- field-even-active: Active-high Field ID output polarity control of the bus. + Under normal operation, the field ID output is set to logic 1 for an odd field + (field 1) and set to logic 0 for an even field (field 0). + 0 = Normal Operation (Active Low, Default) + 1 = FID output polarity inverted + +For further reading of port node refer Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp7002@5c { + compatible = "ti,tvp7002"; + reg = <0x5c>; + + port { + tvp7002_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + sync-on-green-active = <1>; + field-even-active = <0>; + }; + }; + }; + ... + }; |