diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/ti-pci.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/ti-pci.txt | 102 |
1 files changed, 102 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt new file mode 100644 index 000000000..d5cbfe6b0 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -0,0 +1,102 @@ +TI PCI Controllers + +PCIe DesignWare Controller + - compatible: Should be "ti,dra7-pcie" for RC (deprecated) + Should be "ti,dra7-pcie-ep" for EP (deprecated) + Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode + Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode + Should be "ti,dra726-pcie-rc" for dra72x in RC mode + Should be "ti,dra726-pcie-ep" for dra72x in EP mode + - phys : list of PHY specifiers (used by generic PHY framework) + - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. + - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", + where <X> is the instance number of the pcie from the HW spec. + - num-lanes as specified in ../designware-pcie.txt + - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control + module and the register offset to specify lane + selection. + +HOST MODE +========= + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI-specific registers + The second entry must be "rc-dbics" for the DesignWare PCIe + registers + The third entry must be "config" for the PCIe configuration space + - interrupts : Two interrupt entries must be specified. The first one is for + main interrupt line and the second for MSI interrupt line. + - #address-cells, + #size-cells, + #interrupt-cells, + device_type, + ranges, + interrupt-map-mask, + interrupt-map : as specified in ../designware-pcie.txt + - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument + should contain the register offset within syscon + and the 2nd argument should contain the bit field + for setting the bit to enable unaligned + access. + +DEVICE MODE +=========== + - reg : Four register ranges as listed in the reg-names property + - reg-names : "ti-conf" for the TI-specific registers + "ep_dbics" for the standard configuration registers as + they are locally accessed within the DIF CS space + "ep_dbics2" for the standard configuration registers as + they are locally accessed within the DIF CS2 space + "addr_space" used to map remote RC address space + - interrupts : one interrupt entries must be specified for main interrupt. + - num-ib-windows : number of inbound address translation windows + - num-ob-windows : number of outbound address translation windows + - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument + should contain the register offset within syscon + and the 2nd argument should contain the bit field + for setting the bit to enable unaligned + access. + +Optional Property: + - gpios : Should be added if a GPIO line is required to drive PERST# line + +NOTE: Two DT nodes may be added for each PCI controller; one for host +mode and another for device mode. So in order for PCI to +work in host mode, EP mode DT node should be disabled and in order to PCI to +work in EP mode, host mode DT node should be disabled. Host mode and EP +mode are mutually exclusive. + +Example: +axi { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0x51000000 0x51000000 0x3000 + 0x0 0x20000000 0x10000000>; + pcie@51000000 { + compatible = "ti,dra7-pcie"; + reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; + reg-names = "rc_dbics", "ti_conf", "config"; + interrupts = <0 232 0x4>, <0 233 0x4>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x03000 0 0x00010000 + 0x82000000 0 0x20013000 0x13000 0 0xffed000>; + #interrupt-cells = <1>; + num-lanes = <1>; + ti,hwmods = "pcie1"; + phys = <&pcie1_phy>; + phy-names = "pcie-phy0"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; +}; |