diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator/max8997-regulator.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/max8997-regulator.txt | 144 |
1 files changed, 144 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt new file mode 100644 index 000000000..6fe825b8a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -0,0 +1,144 @@ +* Maxim MAX8997 Voltage and Current Regulator + +The Maxim MAX8997 is a multi-function device which includes voltage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of max8997. + +Required properties: +- compatible: Should be "maxim,max8997-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck1 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck5 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified. + +Optional properties: +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs. +- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: +- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for + multiple bucks, changing the voltage value of one of the bucks may affect + that of another buck, which is the side effect of the change (set_voltage). + Use this property to ignore such side effects and change the voltage. + +- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of max8997 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + standard regulator bindings here + }; + +The following are the names of the regulators that the max8997 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of max8997. + + - LDOn + - valid values for n are 1 to 18 and 21 + - Example: LDO0, LD01, LDO2, LDO21 + - BUCKn + - valid values for n are 1 to 7. + - Example: BUCK1, BUCK2, BUCK3, BUCK7 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + + - CHARGER_CV: main battery charger voltage control + - CHARGER: main battery charger current control + - CHARGER_TOPOFF: end of charge current threshold level + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + max8997_pmic@66 { + compatible = "maxim,max8997-pmic"; + interrupt-parent = <&wakeup_eint>; + reg = <0x66>; + interrupts = <4 0>, <3 0>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>, /* SET2 */ + <&gpx0 2 1 0 0>; /* SET3 */ + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; |