diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound/st,sta350.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/sound/st,sta350.txt | 131 |
1 files changed, 131 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt new file mode 100644 index 000000000..307398ef2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta350.txt @@ -0,0 +1,131 @@ +STA350 audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta350" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - vdd-dig-supply: regulator spec, providing 3.3V + - vdd-pll-supply: regulator spec, providing 3.3V + - vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + This property has to be specified as '/bits/ 8' value. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is chosen. + This properties have to be specified as '/bits/ 8' values. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,ffx-power-output-mode: string + The FFX power output mode selects how the FFX output timing is + configured. Must be one of these values: + - "drop-compensation" + - "tapered-compensation" + - "full-power-mode" + - "variable-drop-compensation" (default) + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,overcurrent-warning-adjustment: + If present, overcurrent warning adjustment is enabled. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,distortion-compensation: + If present, distortion compensation variable uses DCC coefficient. + If not present, preset DC coefficient is used. + + - st,invalid-input-detect-mute: + If present, automatic invalid input detect mute is enabled. + + - st,activate-mute-output: + If present, a mute output will be activated in ase the volume will + reach a value lower than -76 dBFS. + + - st,bridge-immediate-off: + If present, the bridge will be switched off immediately after the + power-down-gpio goes low. Otherwise, the bridge will wait for 13 + million clock cycles to pass before shutting down. + + - st,noise-shape-dc-cut: + If present, the noise-shaping technique on the DC cutoff filter are + enabled. + + - st,powerdown-master-volume: + If present, the power-down pin and I2C power-down functions will + act on the master volume. Otherwise, the functions will act on the + mute commands. + + - st,powerdown-delay-divider: + If present, the bridge power-down time will be divided by the provided + value. If not specified, a divider of 1 will be used. Allowed values + are 1, 2, 4, 8, 16, 32, 64 and 128. + This property has to be specified as '/bits/ 8' value. + +Example: + +codec: sta350@38 { + compatible = "st,sta350"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; |