diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound/tlv320adcx140.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/sound/tlv320adcx140.yaml | 209 |
1 files changed, 209 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml new file mode 100644 index 000000000..df18be9d7 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml @@ -0,0 +1,209 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/tlv320adcx140.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TLV320ADCX140 Quad Channel Analog-to-Digital Converter + +maintainers: + - Dan Murphy <dmurphy@ti.com> + +description: | + The TLV320ADCX140 are multichannel (4-ch analog recording or 8-ch digital + PDM microphones recording), high-performance audio, analog-to-digital + converter (ADC) with analog inputs supporting up to 2V RMS. The TLV320ADCX140 + family supports line and microphone Inputs, and offers a programmable + microphone bias or supply voltage generation. + + Specifications can be found at: + https://www.ti.com/lit/ds/symlink/tlv320adc3140.pdf + https://www.ti.com/lit/ds/symlink/tlv320adc5140.pdf + https://www.ti.com/lit/ds/symlink/tlv320adc6140.pdf + +properties: + compatible: + oneOf: + - const: ti,tlv320adc3140 + - const: ti,tlv320adc5140 + - const: ti,tlv320adc6140 + + reg: + maxItems: 1 + description: | + I2C addresss of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f + + reset-gpios: + description: | + GPIO used for hardware reset. + + areg-supply: + description: | + Regulator with AVDD at 3.3V. If not defined then the internal regulator + is enabled. + + ti,mic-bias-source: + description: | + Indicates the source for MIC Bias. + 0 - Mic bias is set to VREF + 1 - Mic bias is set to VREF × 1.096 + 6 - Mic bias is set to AVDD + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 6] + + ti,vref-source: + description: | + Indicates the source for MIC Bias. + 0 - Set VREF to 2.75V + 1 - Set VREF to 2.5V + 2 - Set VREF to 1.375V + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + ti,pdm-edge-select: + description: | + Defines the PDMCLK sampling edge configuration for the PDM inputs. This + array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>. + + 0 - (default) Odd channel is latched on the negative edge and even + channel is latched on the the positive edge. + 1 - Odd channel is latched on the positive edge and even channel is + latched on the the negative edge. + + PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data + PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data + PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data + PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data + + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + items: + maximum: 1 + default: [0, 0, 0, 0] + + ti,gpi-config: + description: | + Defines the configuration for the general purpose input pins (GPI). + The array is defined as <GPI1 GPI2 GPI3 GPI4>. + + 0 - (default) disabled + 1 - GPIX is configured as a general-purpose input (GPI) + 2 - GPIX is configured as a master clock input (MCLK) + 3 - GPIX is configured as an ASI input for daisy-chain (SDIN) + 4 - GPIX is configured as a PDM data input for channel 1 and channel + (PDMDIN1) + 5 - GPIX is configured as a PDM data input for channel 3 and channel + (PDMDIN2) + 6 - GPIX is configured as a PDM data input for channel 5 and channel + (PDMDIN3) + 7 - GPIX is configured as a PDM data input for channel 7 and channel + (PDMDIN4) + + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + items: + maximum: 7 + default: [0, 0, 0, 0] + + ti,asi-tx-drive: + type: boolean + description: | + When set the device will set the Tx ASI output to a Hi-Z state for unused + data cycles. Default is to drive the output low on unused ASI cycles. + +patternProperties: + '^ti,gpo-config-[1-4]$': + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + Defines the configuration and output driver for the general purpose + output pins (GPO). These values are pairs, the first value is for the + configuration type and the second value is for the output drive type. + The array is defined as <GPO_CFG GPO_DRV> + + GPO output configuration can be one of the following: + + 0 - (default) disabled + 1 - GPOX is configured as a general-purpose output (GPO) + 2 - GPOX is configured as a device interrupt output (IRQ) + 3 - GPOX is configured as a secondary ASI output (SDOUT2) + 4 - GPOX is configured as a PDM clock output (PDMCLK) + + GPO output drive configuration for the GPO pins can be one of the following: + + 0d - (default) Hi-Z output + 1d - Drive active low and active high + 2d - Drive active low and weak high + 3d - Drive active low and Hi-Z + 4d - Drive weak low and active high + 5d - Drive Hi-Z and active high + + ti,gpio-config: + description: | + Defines the configuration and output drive for the General Purpose + Input and Output pin (GPIO1). Its value is a pair, the first value is for + the configuration type and the second value is for the output drive + type. The array is defined as <GPIO1_CFG GPIO1_DRV> + + configuration for the GPIO pin can be one of the following: + 0 - disabled + 1 - GPIO1 is configured as a general-purpose output (GPO) + 2 - (default) GPIO1 is configured as a device interrupt output (IRQ) + 3 - GPIO1 is configured as a secondary ASI output (SDOUT2) + 4 - GPIO1 is configured as a PDM clock output (PDMCLK) + 8 - GPIO1 is configured as an input to control when MICBIAS turns on or + off (MICBIAS_EN) + 9 - GPIO1 is configured as a general-purpose input (GPI) + 10 - GPIO1 is configured as a master clock input (MCLK) + 11 - GPIO1 is configured as an ASI input for daisy-chain (SDIN) + 12 - GPIO1 is configured as a PDM data input for channel 1 and channel 2 + (PDMDIN1) + 13 - GPIO1 is configured as a PDM data input for channel 3 and channel 4 + (PDMDIN2) + 14 - GPIO1 is configured as a PDM data input for channel 5 and channel 6 + (PDMDIN3) + 15 - GPIO1 is configured as a PDM data input for channel 7 and channel 8 + (PDMDIN4) + + output drive type for the GPIO pin can be one of the following: + 0 - Hi-Z output + 1 - Drive active low and active high + 2 - (default) Drive active low and weak high + 3 - Drive active low and Hi-Z + 4 - Drive weak low and active high + 5 - Drive Hi-Z and active high + + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 2 + maxItems: 2 + items: + maximum: 15 + default: [2, 2] + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + codec: codec@4c { + compatible = "ti,tlv320adc5140"; + reg = <0x4c>; + ti,mic-bias-source = <6>; + ti,pdm-edge-select = <0 1 0 1>; + ti,gpi-config = <4 5 6 7>; + ti,gpio-config = <10 2>; + ti,gpo-config-1 = <0 0>; + ti,gpo-config-2 = <0 0>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + }; + }; |