diff options
Diffstat (limited to 'arch/arm/boot/dts/ls1021a-tsn.dts')
| -rw-r--r-- | arch/arm/boot/dts/ls1021a-tsn.dts | 293 |
1 files changed, 293 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts new file mode 100644 index 000000000..aca78b5ed --- /dev/null +++ b/arch/arm/boot/dts/ls1021a-tsn.dts @@ -0,0 +1,293 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright 2016-2018 NXP Semiconductors + * Copyright 2019 Vladimir Oltean <olteanv@gmail.com> + */ + +/dts-v1/; +#include "ls1021a.dtsi" + +/ { + model = "NXP LS1021A-TSN Board"; + + sys_mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; + + reg_vdda_codec: regulator-3V3 { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vddio_codec: regulator-2V5 { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; +}; + +&dspi0 { + bus-num = <0>; + status = "okay"; + + /* ADG704BRMZ 1:4 SPI mux/demux */ + sja1105: ethernet-switch@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,sja1105t"; + /* 12 MHz */ + spi-max-frequency = <12000000>; + /* Sample data on trailing clock edge */ + spi-cpha; + /* SPI controller settings for SJA1105 timing requirements */ + fsl,spi-cs-sck-delay = <1000>; + fsl,spi-sck-cs-delay = <1000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + /* ETH5 written on chassis */ + label = "swp5"; + phy-handle = <&rgmii_phy6>; + phy-mode = "rgmii-id"; + reg = <0>; + }; + + port@1 { + /* ETH2 written on chassis */ + label = "swp2"; + phy-handle = <&rgmii_phy3>; + phy-mode = "rgmii-id"; + reg = <1>; + }; + + port@2 { + /* ETH3 written on chassis */ + label = "swp3"; + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + reg = <2>; + }; + + port@3 { + /* ETH4 written on chassis */ + label = "swp4"; + phy-handle = <&rgmii_phy5>; + phy-mode = "rgmii-id"; + reg = <3>; + }; + + port@4 { + /* Internal port connected to eth2 */ + ethernet = <&enet2>; + phy-mode = "rgmii"; + reg = <4>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&enet0 { + tbi-handle = <&tbi0>; + phy-handle = <&sgmii_phy2>; + phy-mode = "sgmii"; + status = "okay"; +}; + +&enet1 { + tbi-handle = <&tbi1>; + phy-handle = <&sgmii_phy1>; + phy-mode = "sgmii"; + status = "okay"; +}; + +/* RGMII delays added via PCB traces */ +&enet2 { + phy-mode = "rgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&esdhc { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + /* 3 axis accelerometer */ + accelerometer@1e { + compatible = "fsl,fxls8471"; + position = <0>; + reg = <0x1e>; + }; + + /* Audio codec (SAI2) */ + audio-codec@2a { + compatible = "fsl,sgtl5000"; + VDDIO-supply = <®_vddio_codec>; + VDDA-supply = <®_vdda_codec>; + #sound-dai-cells = <0>; + clocks = <&sys_mclk>; + reg = <0x2a>; + }; + + /* Current sensing circuit for 1V VDDCORE PMIC rail */ + current-sensor@44 { + compatible = "ti,ina220"; + shunt-resistor = <1000>; + reg = <0x44>; + }; + + /* Current sensing circuit for 12V VCC rail */ + current-sensor@45 { + compatible = "ti,ina220"; + shunt-resistor = <1000>; + reg = <0x45>; + }; + + /* Thermal monitor - case */ + temperature-sensor@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + + /* Thermal monitor - chip */ + temperature-sensor@4c { + compatible = "ti,tmp451"; + reg = <0x4c>; + }; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + }; + + /* Unsupported devices: + * - FXAS21002C Gyroscope at 0x20 + * - TI ADS7924 4-channel ADC at 0x49 + */ +}; + +&ifc { + status = "disabled"; +}; + +&lpuart0 { + status = "okay"; +}; + +&lpuart3 { + status = "okay"; +}; + +&mdio0 { + /* AR8031 */ + sgmii_phy1: ethernet-phy@1 { + reg = <0x1>; + /* SGMII1_PHY_INT_B: connected to IRQ2, active low */ + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>; + }; + + /* AR8031 */ + sgmii_phy2: ethernet-phy@2 { + reg = <0x2>; + /* SGMII2_PHY_INT_B: connected to IRQ2, active low */ + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>; + }; + + /* BCM5464 quad PHY */ + rgmii_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + + rgmii_phy4: ethernet-phy@4 { + reg = <0x4>; + }; + + rgmii_phy5: ethernet-phy@5 { + reg = <0x5>; + }; + + rgmii_phy6: ethernet-phy@6 { + reg = <0x6>; + }; + + /* SGMII PCS for enet0 */ + tbi0: tbi-phy@1f { + reg = <0x1f>; + device_type = "tbi-phy"; + }; +}; + +&mdio1 { + /* SGMII PCS for enet1 */ + tbi1: tbi-phy@1f { + reg = <0x1f>; + device_type = "tbi-phy"; + }; +}; + +&qspi { + status = "okay"; + + flash@0 { + /* Rev. A uses 64MB flash, Rev. B & C use 32MB flash */ + compatible = "jedec,spi-nor"; + spi-max-frequency = <20000000>; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "RCW"; + reg = <0x0 0x40000>; + }; + + partition@40000 { + label = "U-Boot"; + reg = <0x40000 0x300000>; + }; + + partition@340000 { + label = "U-Boot Env"; + reg = <0x340000 0x100000>; + }; + }; + }; +}; + +&sai2 { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; |