diff options
Diffstat (limited to 'arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts')
| -rw-r--r-- | arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts | 281 |
1 files changed, 281 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts new file mode 100644 index 000000000..942e3a2ca --- /dev/null +++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts @@ -0,0 +1,281 @@ +/* + * Device Tree Source for mangOH Green Board with WP8548 Module + * + * Copyright (C) 2016 BayLibre, SAS. + * Author : Neil Armstrong <narmstrong@baylibre.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/input/input.h> + +#include "qcom-mdm9615-wp8548.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "MangOH Green with WP8548 Module"; + compatible = "swir,mangoh-green-wp8548", "swir,wp8548", "qcom,mdm9615"; + + aliases { + spi0 = &gsbi3_spi; + serial0 = &gsbi4_serial; + serial1 = &gsbi5_serial; + i2c0 = &gsbi5_i2c; + mmc0 = &sdcc1; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; +}; + +&msmgpio { + /* MangOH GPIO Mapping : + * - 2 : GPIOEXP_INT2 + * - 7 : IOT1_GPIO2 + * - 8 : IOT0_GPIO4 + * - 13: IOT0_GPIO3 + * - 21: IOT1_GPIO4 + * - 22: IOT2_GPIO1 + * - 23: IOT2_GPIO2 + * - 24: IOT2_GPIO3 + * - 25: IOT1_GPIO1 + * - 32: IOT1_GPIO3 + * - 33: IOT0_GPIO2 + * - 42: IOT0_GPIO1 and SD Card Detect + */ + + gpioext1_pins: gpioext1_pins { + pins { + pins = "gpio2"; + function = "gpio"; + input-enable; + bias-disable; + }; + }; + + sdc_cd_pins: sdc_cd_pins { + pins { + pins = "gpio42"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&gsbi3_spi { + spi@0 { + compatible = "swir,mangoh-iotport-spi", "spidev"; + spi-max-frequency = <24000000>; + reg = <0>; + }; +}; + +&gsbi5_i2c { + mux@71 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + + i2c_iot0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c_iot1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + i2c_iot2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + usbhub: hub@8 { + compatible = "smsc,usb3503a"; + reg = <0x8>; + connect-gpios = <&gpioext2 1 GPIO_ACTIVE_HIGH>; + intn-gpios = <&gpioext2 0 GPIO_ACTIVE_HIGH>; + initial-mode = <1>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + gpioext0: gpio@3e { + /* GPIO Expander 0 Mapping : + * - 0: ARDUINO_RESET_Level shift + * - 1: BattChrgr_PG_N + * - 2: BattGauge_GPIO + * - 3: LED_ON (out active high) + * - 4: ATmega_reset_GPIO + * - 5: X + * - 6: PCM_ANALOG_SELECT (out active high) + * - 7: X + * - 8: Board_rev_res1 (in) + * - 9: Board_rev_res2 (in) + * - 10: UART_EXP1_ENn (out active low / pull-down) + * - 11: UART_EXP1_IN (out pull-down) + * - 12: UART_EXP2_IN (out pull-down) + * - 13: SDIO_SEL (out pull-down) + * - 14: SPI_EXP1_ENn (out active low / pull-down) + * - 15: SPI_EXP1_IN (out pull-down) + */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x3e>; + interrupt-parent = <&gpioext1>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + + probe-reset; + + gpio-controller; + interrupt-controller; + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + + gpioext1: gpio@3f { + /* GPIO Expander 1 Mapping : + * - 0: GPIOEXP_INT1 + * - 1: Battery detect + * - 2: GPIO_SCF3_RESET + * - 3: LED_CARD_DETECT_IOT0 (in) + * - 4: LED_CARD_DETECT_IOT1 (in) + * - 5: LED_CARD_DETECT_IOT2 (in) + * - 6: UIM2_PWM_SELECT + * - 7: UIM2_M2_S_SELECT + * - 8: TP900 + * - 9: SENSOR_INT1 (in) + * - 10: SENSOR_INT2 (in) + * - 11: CARD_DETECT_IOT0 (in pull-up) + * - 12: CARD_DETECT_IOT2 (in pull-up) + * - 13: CARD_DETECT_IOT1 (in pull-up) + * - 14: GPIOEXP_INT3 (in active low / pull-up) + * - 15: BattChrgr_INT_N + */ + pinctrl-0 = <&gpioext1_pins>; + pinctrl-names = "default"; + + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x3f>; + interrupt-parent = <&msmgpio>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + + probe-reset; + + gpio-controller; + interrupt-controller; + }; + }; + + i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + + gpioext2: gpio@70 { + /* GPIO Expander 2 Mapping : + * - 0: USB_HUB_INTn + * - 1: HUB_CONNECT + * - 2: GPIO_IOT2_RESET (out active low / pull-up) + * - 3: GPIO_IOT1_RESET (out active low / pull-up) + * - 4: GPIO_IOT0_RESET (out active low / pull-up) + * - 5: TP901 + * - 6: TP902 + * - 7: TP903 + * - 8: UART_EXP2_ENn (out active low / pull-down) + * - 9: PCM_EXP1_ENn (out active low) + * - 10: PCM_EXP1_SEL (out) + * - 11: ARD_FTDI + * - 12: TP904 + * - 13: TP905 + * - 14: TP906 + * - 15: RS232_Enable (out active high / pull-up) + */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x70>; + interrupt-parent = <&gpioext1>; + interrupts = <14 IRQ_TYPE_EDGE_FALLING>; + + probe-reset; + + gpio-controller; + interrupt-controller; + }; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; + }; +}; + +&sdcc1 { + pinctrl-0 = <&sdc_cd_pins>; + pinctrl-names = "default"; + disable-wp; + cd-gpios = <&msmgpio 42 GPIO_ACTIVE_LOW>; /* Active low CD */ +}; |