diff options
Diffstat (limited to 'drivers/ata/pata_opti.c')
| -rw-r--r-- | drivers/ata/pata_opti.c | 200 |
1 files changed, 200 insertions, 0 deletions
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c new file mode 100644 index 000000000..06a800a3b --- /dev/null +++ b/drivers/ata/pata_opti.c @@ -0,0 +1,200 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * pata_opti.c - ATI PATA for new ATA layer + * (C) 2005 Red Hat Inc + * + * Based on + * linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002 + * + * Copyright (C) 1996-1998 Linus Torvalds & authors (see below) + * + * Authors: + * Jaromir Koutek <miri@punknet.cz>, + * Jan Harkes <jaharkes@cwi.nl>, + * Mark Lord <mlord@pobox.com> + * Some parts of code are from ali14xx.c and from rz1000.c. + * + * Also consulted the FreeBSD prototype driver by Kevin Day to try + * and resolve some confusions. Further documentation can be found in + * Ralf Brown's interrupt list + * + * If you have other variants of the Opti range (Viper/Vendetta) please + * try this driver with those PCI idents and report back. For the later + * chips see the pata_optidma driver + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_opti" +#define DRV_VERSION "0.2.9" + +enum { + READ_REG = 0, /* index of Read cycle timing register */ + WRITE_REG = 1, /* index of Write cycle timing register */ + CNTRL_REG = 3, /* index of Control register */ + STRAP_REG = 5, /* index of Strap register */ + MISC_REG = 6 /* index of Miscellaneous register */ +}; + +/** + * opti_pre_reset - probe begin + * @link: ATA link + * @deadline: deadline jiffies for the operation + * + * Set up cable type and use generic probe init + */ + +static int opti_pre_reset(struct ata_link *link, unsigned long deadline) +{ + struct ata_port *ap = link->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits opti_enable_bits[] = { + { 0x45, 1, 0x80, 0x00 }, + { 0x40, 1, 0x08, 0x00 } + }; + + if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no])) + return -ENOENT; + + return ata_sff_prereset(link, deadline); +} + +/** + * opti_write_reg - control register setup + * @ap: ATA port + * @value: value + * @reg: control register number + * + * The Opti uses magic 'trapdoor' register accesses to do configuration + * rather than using PCI space as other controllers do. The double inw + * on the error register activates configuration mode. We can then write + * the control register + */ + +static void opti_write_reg(struct ata_port *ap, u8 val, int reg) +{ + void __iomem *regio = ap->ioaddr.cmd_addr; + + /* These 3 unlock the control register access */ + ioread16(regio + 1); + ioread16(regio + 1); + iowrite8(3, regio + 2); + + /* Do the I/O */ + iowrite8(val, regio + reg); + + /* Relock */ + iowrite8(0x83, regio + 2); +} + +/** + * opti_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. Timing numbers are taken from + * the FreeBSD driver then pre computed to keep the code clean. There + * are two tables depending on the hardware clock speed. + */ + +static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct ata_device *pair = ata_dev_pair(adev); + int clock; + int pio = adev->pio_mode - XFER_PIO_0; + void __iomem *regio = ap->ioaddr.cmd_addr; + u8 addr; + + /* Address table precomputed with prefetch off and a DCLK of 2 */ + static const u8 addr_timing[2][5] = { + { 0x30, 0x20, 0x20, 0x10, 0x10 }, + { 0x20, 0x20, 0x10, 0x10, 0x10 } + }; + static const u8 data_rec_timing[2][5] = { + { 0x6B, 0x56, 0x42, 0x32, 0x31 }, + { 0x58, 0x44, 0x32, 0x22, 0x21 } + }; + + iowrite8(0xff, regio + 5); + clock = ioread16(regio + 5) & 1; + + /* + * As with many controllers the address setup time is shared + * and must suit both devices if present. + */ + + addr = addr_timing[clock][pio]; + if (pair) { + /* Hardware constraint */ + u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0]; + if (pair_addr > addr) + addr = pair_addr; + } + + /* Commence primary programming sequence */ + opti_write_reg(ap, adev->devno, MISC_REG); + opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG); + opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG); + opti_write_reg(ap, addr, MISC_REG); + + /* Programming sequence complete, override strapping */ + opti_write_reg(ap, 0x85, CNTRL_REG); +} + +static struct scsi_host_template opti_sht = { + ATA_PIO_SHT(DRV_NAME), +}; + +static struct ata_port_operations opti_port_ops = { + .inherits = &ata_sff_port_ops, + .cable_detect = ata_cable_40wire, + .set_piomode = opti_set_piomode, + .prereset = opti_pre_reset, +}; + +static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .port_ops = &opti_port_ops + }; + const struct ata_port_info *ppi[] = { &info, NULL }; + + ata_print_version_once(&dev->dev, DRV_VERSION); + + return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0); +} + +static const struct pci_device_id opti[] = { + { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 }, + { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 }, + + { }, +}; + +static struct pci_driver opti_pci_driver = { + .name = DRV_NAME, + .id_table = opti, + .probe = opti_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(opti_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Opti 621/621X"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, opti); +MODULE_VERSION(DRV_VERSION); |