diff options
Diffstat (limited to 'drivers/input/serio/hp_sdc.c')
| -rw-r--r-- | drivers/input/serio/hp_sdc.c | 1127 |
1 files changed, 1127 insertions, 0 deletions
diff --git a/drivers/input/serio/hp_sdc.c b/drivers/input/serio/hp_sdc.c new file mode 100644 index 000000000..13eacf6ab --- /dev/null +++ b/drivers/input/serio/hp_sdc.c @@ -0,0 +1,1127 @@ +/* + * HP i8042-based System Device Controller driver. + * + * Copyright (c) 2001 Brian S. Julin + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL"). + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * + * References: + * System Device Controller Microprocessor Firmware Theory of Operation + * for Part Number 1820-4784 Revision B. Dwg No. A-1820-4784-2 + * Helge Deller's original hilkbd.c port for PA-RISC. + * + * + * Driver theory of operation: + * + * hp_sdc_put does all writing to the SDC. ISR can run on a different + * CPU than hp_sdc_put, but only one CPU runs hp_sdc_put at a time + * (it cannot really benefit from SMP anyway.) A tasket fit this perfectly. + * + * All data coming back from the SDC is sent via interrupt and can be read + * fully in the ISR, so there are no latency/throughput problems there. + * The problem is with output, due to the slow clock speed of the SDC + * compared to the CPU. This should not be too horrible most of the time, + * but if used with HIL devices that support the multibyte transfer command, + * keeping outbound throughput flowing at the 6500KBps that the HIL is + * capable of is more than can be done at HZ=100. + * + * Busy polling for IBF clear wastes CPU cycles and bus cycles. hp_sdc.ibf + * is set to 0 when the IBF flag in the status register has cleared. ISR + * may do this, and may also access the parts of queued transactions related + * to reading data back from the SDC, but otherwise will not touch the + * hp_sdc state. Whenever a register is written hp_sdc.ibf is set to 1. + * + * The i8042 write index and the values in the 4-byte input buffer + * starting at 0x70 are kept track of in hp_sdc.wi, and .r7[], respectively, + * to minimize the amount of IO needed to the SDC. However these values + * do not need to be locked since they are only ever accessed by hp_sdc_put. + * + * A timer task schedules the tasklet once per second just to make + * sure it doesn't freeze up and to allow for bad reads to time out. + */ + +#include <linux/hp_sdc.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/time.h> +#include <linux/semaphore.h> +#include <linux/slab.h> +#include <linux/hil.h> +#include <asm/io.h> + +/* Machine-specific abstraction */ + +#if defined(__hppa__) +# include <asm/parisc-device.h> +# define sdc_readb(p) gsc_readb(p) +# define sdc_writeb(v,p) gsc_writeb((v),(p)) +#elif defined(__mc68000__) +#include <linux/uaccess.h> +# define sdc_readb(p) in_8(p) +# define sdc_writeb(v,p) out_8((p),(v)) +#else +# error "HIL is not supported on this platform" +#endif + +#define PREFIX "HP SDC: " + +MODULE_AUTHOR("Brian S. Julin <bri@calyx.com>"); +MODULE_DESCRIPTION("HP i8042-based SDC Driver"); +MODULE_LICENSE("Dual BSD/GPL"); + +EXPORT_SYMBOL(hp_sdc_request_timer_irq); +EXPORT_SYMBOL(hp_sdc_request_hil_irq); +EXPORT_SYMBOL(hp_sdc_request_cooked_irq); + +EXPORT_SYMBOL(hp_sdc_release_timer_irq); +EXPORT_SYMBOL(hp_sdc_release_hil_irq); +EXPORT_SYMBOL(hp_sdc_release_cooked_irq); + +EXPORT_SYMBOL(__hp_sdc_enqueue_transaction); +EXPORT_SYMBOL(hp_sdc_enqueue_transaction); +EXPORT_SYMBOL(hp_sdc_dequeue_transaction); + +static bool hp_sdc_disabled; +module_param_named(no_hpsdc, hp_sdc_disabled, bool, 0); +MODULE_PARM_DESC(no_hpsdc, "Do not enable HP SDC driver."); + +static hp_i8042_sdc hp_sdc; /* All driver state is kept in here. */ + +/*************** primitives for use in any context *********************/ +static inline uint8_t hp_sdc_status_in8(void) +{ + uint8_t status; + unsigned long flags; + + write_lock_irqsave(&hp_sdc.ibf_lock, flags); + status = sdc_readb(hp_sdc.status_io); + if (!(status & HP_SDC_STATUS_IBF)) + hp_sdc.ibf = 0; + write_unlock_irqrestore(&hp_sdc.ibf_lock, flags); + + return status; +} + +static inline uint8_t hp_sdc_data_in8(void) +{ + return sdc_readb(hp_sdc.data_io); +} + +static inline void hp_sdc_status_out8(uint8_t val) +{ + unsigned long flags; + + write_lock_irqsave(&hp_sdc.ibf_lock, flags); + hp_sdc.ibf = 1; + if ((val & 0xf0) == 0xe0) + hp_sdc.wi = 0xff; + sdc_writeb(val, hp_sdc.status_io); + write_unlock_irqrestore(&hp_sdc.ibf_lock, flags); +} + +static inline void hp_sdc_data_out8(uint8_t val) +{ + unsigned long flags; + + write_lock_irqsave(&hp_sdc.ibf_lock, flags); + hp_sdc.ibf = 1; + sdc_writeb(val, hp_sdc.data_io); + write_unlock_irqrestore(&hp_sdc.ibf_lock, flags); +} + +/* Care must be taken to only invoke hp_sdc_spin_ibf when + * absolutely needed, or in rarely invoked subroutines. + * Not only does it waste CPU cycles, it also wastes bus cycles. + */ +static inline void hp_sdc_spin_ibf(void) +{ + unsigned long flags; + rwlock_t *lock; + + lock = &hp_sdc.ibf_lock; + + read_lock_irqsave(lock, flags); + if (!hp_sdc.ibf) { + read_unlock_irqrestore(lock, flags); + return; + } + read_unlock(lock); + write_lock(lock); + while (sdc_readb(hp_sdc.status_io) & HP_SDC_STATUS_IBF) + { } + hp_sdc.ibf = 0; + write_unlock_irqrestore(lock, flags); +} + + +/************************ Interrupt context functions ************************/ +static void hp_sdc_take(int irq, void *dev_id, uint8_t status, uint8_t data) +{ + hp_sdc_transaction *curr; + + read_lock(&hp_sdc.rtq_lock); + if (hp_sdc.rcurr < 0) { + read_unlock(&hp_sdc.rtq_lock); + return; + } + curr = hp_sdc.tq[hp_sdc.rcurr]; + read_unlock(&hp_sdc.rtq_lock); + + curr->seq[curr->idx++] = status; + curr->seq[curr->idx++] = data; + hp_sdc.rqty -= 2; + hp_sdc.rtime = ktime_get(); + + if (hp_sdc.rqty <= 0) { + /* All data has been gathered. */ + if (curr->seq[curr->actidx] & HP_SDC_ACT_SEMAPHORE) + if (curr->act.semaphore) + up(curr->act.semaphore); + + if (curr->seq[curr->actidx] & HP_SDC_ACT_CALLBACK) + if (curr->act.irqhook) + curr->act.irqhook(irq, dev_id, status, data); + + curr->actidx = curr->idx; + curr->idx++; + /* Return control of this transaction */ + write_lock(&hp_sdc.rtq_lock); + hp_sdc.rcurr = -1; + hp_sdc.rqty = 0; + write_unlock(&hp_sdc.rtq_lock); + tasklet_schedule(&hp_sdc.task); + } +} + +static irqreturn_t hp_sdc_isr(int irq, void *dev_id) +{ + uint8_t status, data; + + status = hp_sdc_status_in8(); + /* Read data unconditionally to advance i8042. */ + data = hp_sdc_data_in8(); + + /* For now we are ignoring these until we get the SDC to behave. */ + if (((status & 0xf1) == 0x51) && data == 0x82) + return IRQ_HANDLED; + + switch (status & HP_SDC_STATUS_IRQMASK) { + case 0: /* This case is not documented. */ + break; + + case HP_SDC_STATUS_USERTIMER: + case HP_SDC_STATUS_PERIODIC: + case HP_SDC_STATUS_TIMER: + read_lock(&hp_sdc.hook_lock); + if (hp_sdc.timer != NULL) + hp_sdc.timer(irq, dev_id, status, data); + read_unlock(&hp_sdc.hook_lock); + break; + + case HP_SDC_STATUS_REG: + hp_sdc_take(irq, dev_id, status, data); + break; + + case HP_SDC_STATUS_HILCMD: + case HP_SDC_STATUS_HILDATA: + read_lock(&hp_sdc.hook_lock); + if (hp_sdc.hil != NULL) + hp_sdc.hil(irq, dev_id, status, data); + read_unlock(&hp_sdc.hook_lock); + break; + + case HP_SDC_STATUS_PUP: + read_lock(&hp_sdc.hook_lock); + if (hp_sdc.pup != NULL) + hp_sdc.pup(irq, dev_id, status, data); + else + printk(KERN_INFO PREFIX "HP SDC reports successful PUP.\n"); + read_unlock(&hp_sdc.hook_lock); + break; + + default: + read_lock(&hp_sdc.hook_lock); + if (hp_sdc.cooked != NULL) + hp_sdc.cooked(irq, dev_id, status, data); + read_unlock(&hp_sdc.hook_lock); + break; + } + + return IRQ_HANDLED; +} + + +static irqreturn_t hp_sdc_nmisr(int irq, void *dev_id) +{ + int status; + + status = hp_sdc_status_in8(); + printk(KERN_WARNING PREFIX "NMI !\n"); + +#if 0 + if (status & HP_SDC_NMISTATUS_FHS) { + read_lock(&hp_sdc.hook_lock); + if (hp_sdc.timer != NULL) + hp_sdc.timer(irq, dev_id, status, 0); + read_unlock(&hp_sdc.hook_lock); + } else { + /* TODO: pass this on to the HIL handler, or do SAK here? */ + printk(KERN_WARNING PREFIX "HIL NMI\n"); + } +#endif + + return IRQ_HANDLED; +} + + +/***************** Kernel (tasklet) context functions ****************/ + +unsigned long hp_sdc_put(void); + +static void hp_sdc_tasklet(unsigned long foo) +{ + write_lock_irq(&hp_sdc.rtq_lock); + + if (hp_sdc.rcurr >= 0) { + ktime_t now = ktime_get(); + + if (ktime_after(now, ktime_add_us(hp_sdc.rtime, + HP_SDC_MAX_REG_DELAY))) { + hp_sdc_transaction *curr; + uint8_t tmp; + + curr = hp_sdc.tq[hp_sdc.rcurr]; + /* If this turns out to be a normal failure mode + * we'll need to figure out a way to communicate + * it back to the application. and be less verbose. + */ + printk(KERN_WARNING PREFIX "read timeout (%lldus)!\n", + ktime_us_delta(now, hp_sdc.rtime)); + curr->idx += hp_sdc.rqty; + hp_sdc.rqty = 0; + tmp = curr->seq[curr->actidx]; + curr->seq[curr->actidx] |= HP_SDC_ACT_DEAD; + if (tmp & HP_SDC_ACT_SEMAPHORE) + if (curr->act.semaphore) + up(curr->act.semaphore); + + if (tmp & HP_SDC_ACT_CALLBACK) { + /* Note this means that irqhooks may be called + * in tasklet/bh context. + */ + if (curr->act.irqhook) + curr->act.irqhook(0, NULL, 0, 0); + } + + curr->actidx = curr->idx; + curr->idx++; + hp_sdc.rcurr = -1; + } + } + write_unlock_irq(&hp_sdc.rtq_lock); + hp_sdc_put(); +} + +unsigned long hp_sdc_put(void) +{ + hp_sdc_transaction *curr; + uint8_t act; + int idx, curridx; + + int limit = 0; + + write_lock(&hp_sdc.lock); + + /* If i8042 buffers are full, we cannot do anything that + requires output, so we skip to the administrativa. */ + if (hp_sdc.ibf) { + hp_sdc_status_in8(); + if (hp_sdc.ibf) + goto finish; + } + + anew: + /* See if we are in the middle of a sequence. */ + if (hp_sdc.wcurr < 0) + hp_sdc.wcurr = 0; + read_lock_irq(&hp_sdc.rtq_lock); + if (hp_sdc.rcurr == hp_sdc.wcurr) + hp_sdc.wcurr++; + read_unlock_irq(&hp_sdc.rtq_lock); + if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) + hp_sdc.wcurr = 0; + curridx = hp_sdc.wcurr; + + if (hp_sdc.tq[curridx] != NULL) + goto start; + + while (++curridx != hp_sdc.wcurr) { + if (curridx >= HP_SDC_QUEUE_LEN) { + curridx = -1; /* Wrap to top */ + continue; + } + read_lock_irq(&hp_sdc.rtq_lock); + if (hp_sdc.rcurr == curridx) { + read_unlock_irq(&hp_sdc.rtq_lock); + continue; + } + read_unlock_irq(&hp_sdc.rtq_lock); + if (hp_sdc.tq[curridx] != NULL) + break; /* Found one. */ + } + if (curridx == hp_sdc.wcurr) { /* There's nothing queued to do. */ + curridx = -1; + } + hp_sdc.wcurr = curridx; + + start: + + /* Check to see if the interrupt mask needs to be set. */ + if (hp_sdc.set_im) { + hp_sdc_status_out8(hp_sdc.im | HP_SDC_CMD_SET_IM); + hp_sdc.set_im = 0; + goto finish; + } + + if (hp_sdc.wcurr == -1) + goto done; + + curr = hp_sdc.tq[curridx]; + idx = curr->actidx; + + if (curr->actidx >= curr->endidx) { + hp_sdc.tq[curridx] = NULL; + /* Interleave outbound data between the transactions. */ + hp_sdc.wcurr++; + if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) + hp_sdc.wcurr = 0; + goto finish; + } + + act = curr->seq[idx]; + idx++; + + if (curr->idx >= curr->endidx) { + if (act & HP_SDC_ACT_DEALLOC) + kfree(curr); + hp_sdc.tq[curridx] = NULL; + /* Interleave outbound data between the transactions. */ + hp_sdc.wcurr++; + if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) + hp_sdc.wcurr = 0; + goto finish; + } + + while (act & HP_SDC_ACT_PRECMD) { + if (curr->idx != idx) { + idx++; + act &= ~HP_SDC_ACT_PRECMD; + break; + } + hp_sdc_status_out8(curr->seq[idx]); + curr->idx++; + /* act finished? */ + if ((act & HP_SDC_ACT_DURING) == HP_SDC_ACT_PRECMD) + goto actdone; + /* skip quantity field if data-out sequence follows. */ + if (act & HP_SDC_ACT_DATAOUT) + curr->idx++; + goto finish; + } + if (act & HP_SDC_ACT_DATAOUT) { + int qty; + + qty = curr->seq[idx]; + idx++; + if (curr->idx - idx < qty) { + hp_sdc_data_out8(curr->seq[curr->idx]); + curr->idx++; + /* act finished? */ + if (curr->idx - idx >= qty && + (act & HP_SDC_ACT_DURING) == HP_SDC_ACT_DATAOUT) + goto actdone; + goto finish; + } + idx += qty; + act &= ~HP_SDC_ACT_DATAOUT; + } else + while (act & HP_SDC_ACT_DATAREG) { + int mask; + uint8_t w7[4]; + + mask = curr->seq[idx]; + if (idx != curr->idx) { + idx++; + idx += !!(mask & 1); + idx += !!(mask & 2); + idx += !!(mask & 4); + idx += !!(mask & 8); + act &= ~HP_SDC_ACT_DATAREG; + break; + } + + w7[0] = (mask & 1) ? curr->seq[++idx] : hp_sdc.r7[0]; + w7[1] = (mask & 2) ? curr->seq[++idx] : hp_sdc.r7[1]; + w7[2] = (mask & 4) ? curr->seq[++idx] : hp_sdc.r7[2]; + w7[3] = (mask & 8) ? curr->seq[++idx] : hp_sdc.r7[3]; + + if (hp_sdc.wi > 0x73 || hp_sdc.wi < 0x70 || + w7[hp_sdc.wi - 0x70] == hp_sdc.r7[hp_sdc.wi - 0x70]) { + int i = 0; + + /* Need to point the write index register */ + while (i < 4 && w7[i] == hp_sdc.r7[i]) + i++; + + if (i < 4) { + hp_sdc_status_out8(HP_SDC_CMD_SET_D0 + i); + hp_sdc.wi = 0x70 + i; + goto finish; + } + + idx++; + if ((act & HP_SDC_ACT_DURING) == HP_SDC_ACT_DATAREG) + goto actdone; + + curr->idx = idx; + act &= ~HP_SDC_ACT_DATAREG; + break; + } + + hp_sdc_data_out8(w7[hp_sdc.wi - 0x70]); + hp_sdc.r7[hp_sdc.wi - 0x70] = w7[hp_sdc.wi - 0x70]; + hp_sdc.wi++; /* write index register autoincrements */ + { + int i = 0; + + while ((i < 4) && w7[i] == hp_sdc.r7[i]) + i++; + if (i >= 4) { + curr->idx = idx + 1; + if ((act & HP_SDC_ACT_DURING) == + HP_SDC_ACT_DATAREG) + goto actdone; + } + } + goto finish; + } + /* We don't go any further in the command if there is a pending read, + because we don't want interleaved results. */ + read_lock_irq(&hp_sdc.rtq_lock); + if (hp_sdc.rcurr >= 0) { + read_unlock_irq(&hp_sdc.rtq_lock); + goto finish; + } + read_unlock_irq(&hp_sdc.rtq_lock); + + + if (act & HP_SDC_ACT_POSTCMD) { + uint8_t postcmd; + + /* curr->idx should == idx at this point. */ + postcmd = curr->seq[idx]; + curr->idx++; + if (act & HP_SDC_ACT_DATAIN) { + + /* Start a new read */ + hp_sdc.rqty = curr->seq[curr->idx]; + hp_sdc.rtime = ktime_get(); + curr->idx++; + /* Still need to lock here in case of spurious irq. */ + write_lock_irq(&hp_sdc.rtq_lock); + hp_sdc.rcurr = curridx; + write_unlock_irq(&hp_sdc.rtq_lock); + hp_sdc_status_out8(postcmd); + goto finish; + } + hp_sdc_status_out8(postcmd); + goto actdone; + } + + actdone: + if (act & HP_SDC_ACT_SEMAPHORE) + up(curr->act.semaphore); + else if (act & HP_SDC_ACT_CALLBACK) + curr->act.irqhook(0,NULL,0,0); + + if (curr->idx >= curr->endidx) { /* This transaction is over. */ + if (act & HP_SDC_ACT_DEALLOC) + kfree(curr); + hp_sdc.tq[curridx] = NULL; + } else { + curr->actidx = idx + 1; + curr->idx = idx + 2; + } + /* Interleave outbound data between the transactions. */ + hp_sdc.wcurr++; + if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN) + hp_sdc.wcurr = 0; + + finish: + /* If by some quirk IBF has cleared and our ISR has run to + see that that has happened, do it all again. */ + if (!hp_sdc.ibf && limit++ < 20) + goto anew; + + done: + if (hp_sdc.wcurr >= 0) + tasklet_schedule(&hp_sdc.task); + write_unlock(&hp_sdc.lock); + + return 0; +} + +/******* Functions called in either user or kernel context ****/ +int __hp_sdc_enqueue_transaction(hp_sdc_transaction *this) +{ + int i; + + if (this == NULL) { + BUG(); + return -EINVAL; + } + + /* Can't have same transaction on queue twice */ + for (i = 0; i < HP_SDC_QUEUE_LEN; i++) + if (hp_sdc.tq[i] == this) + goto fail; + + this->actidx = 0; + this->idx = 1; + + /* Search for empty slot */ + for (i = 0; i < HP_SDC_QUEUE_LEN; i++) + if (hp_sdc.tq[i] == NULL) { + hp_sdc.tq[i] = this; + tasklet_schedule(&hp_sdc.task); + return 0; + } + + printk(KERN_WARNING PREFIX "No free slot to add transaction.\n"); + return -EBUSY; + + fail: + printk(KERN_WARNING PREFIX "Transaction add failed: transaction already queued?\n"); + return -EINVAL; +} + +int hp_sdc_enqueue_transaction(hp_sdc_transaction *this) { + unsigned long flags; + int ret; + + write_lock_irqsave(&hp_sdc.lock, flags); + ret = __hp_sdc_enqueue_transaction(this); + write_unlock_irqrestore(&hp_sdc.lock,flags); + + return ret; +} + +int hp_sdc_dequeue_transaction(hp_sdc_transaction *this) +{ + unsigned long flags; + int i; + + write_lock_irqsave(&hp_sdc.lock, flags); + + /* TODO: don't remove it if it's not done. */ + + for (i = 0; i < HP_SDC_QUEUE_LEN; i++) + if (hp_sdc.tq[i] == this) + hp_sdc.tq[i] = NULL; + + write_unlock_irqrestore(&hp_sdc.lock, flags); + return 0; +} + + + +/********************** User context functions **************************/ +int hp_sdc_request_timer_irq(hp_sdc_irqhook *callback) +{ + if (callback == NULL || hp_sdc.dev == NULL) + return -EINVAL; + + write_lock_irq(&hp_sdc.hook_lock); + if (hp_sdc.timer != NULL) { + write_unlock_irq(&hp_sdc.hook_lock); + return -EBUSY; + } + + hp_sdc.timer = callback; + /* Enable interrupts from the timers */ + hp_sdc.im &= ~HP_SDC_IM_FH; + hp_sdc.im &= ~HP_SDC_IM_PT; + hp_sdc.im &= ~HP_SDC_IM_TIMERS; + hp_sdc.set_im = 1; + write_unlock_irq(&hp_sdc.hook_lock); + + tasklet_schedule(&hp_sdc.task); + + return 0; +} + +int hp_sdc_request_hil_irq(hp_sdc_irqhook *callback) +{ + if (callback == NULL || hp_sdc.dev == NULL) + return -EINVAL; + + write_lock_irq(&hp_sdc.hook_lock); + if (hp_sdc.hil != NULL) { + write_unlock_irq(&hp_sdc.hook_lock); + return -EBUSY; + } + + hp_sdc.hil = callback; + hp_sdc.im &= ~(HP_SDC_IM_HIL | HP_SDC_IM_RESET); + hp_sdc.set_im = 1; + write_unlock_irq(&hp_sdc.hook_lock); + + tasklet_schedule(&hp_sdc.task); + + return 0; +} + +int hp_sdc_request_cooked_irq(hp_sdc_irqhook *callback) +{ + if (callback == NULL || hp_sdc.dev == NULL) + return -EINVAL; + + write_lock_irq(&hp_sdc.hook_lock); + if (hp_sdc.cooked != NULL) { + write_unlock_irq(&hp_sdc.hook_lock); + return -EBUSY; + } + + /* Enable interrupts from the HIL MLC */ + hp_sdc.cooked = callback; + hp_sdc.im &= ~(HP_SDC_IM_HIL | HP_SDC_IM_RESET); + hp_sdc.set_im = 1; + write_unlock_irq(&hp_sdc.hook_lock); + + tasklet_schedule(&hp_sdc.task); + + return 0; +} + +int hp_sdc_release_timer_irq(hp_sdc_irqhook *callback) +{ + write_lock_irq(&hp_sdc.hook_lock); + if ((callback != hp_sdc.timer) || + (hp_sdc.timer == NULL)) { + write_unlock_irq(&hp_sdc.hook_lock); + return -EINVAL; + } + + /* Disable interrupts from the timers */ + hp_sdc.timer = NULL; + hp_sdc.im |= HP_SDC_IM_TIMERS; + hp_sdc.im |= HP_SDC_IM_FH; + hp_sdc.im |= HP_SDC_IM_PT; + hp_sdc.set_im = 1; + write_unlock_irq(&hp_sdc.hook_lock); + tasklet_schedule(&hp_sdc.task); + + return 0; +} + +int hp_sdc_release_hil_irq(hp_sdc_irqhook *callback) +{ + write_lock_irq(&hp_sdc.hook_lock); + if ((callback != hp_sdc.hil) || + (hp_sdc.hil == NULL)) { + write_unlock_irq(&hp_sdc.hook_lock); + return -EINVAL; + } + + hp_sdc.hil = NULL; + /* Disable interrupts from HIL only if there is no cooked driver. */ + if(hp_sdc.cooked == NULL) { + hp_sdc.im |= (HP_SDC_IM_HIL | HP_SDC_IM_RESET); + hp_sdc.set_im = 1; + } + write_unlock_irq(&hp_sdc.hook_lock); + tasklet_schedule(&hp_sdc.task); + + return 0; +} + +int hp_sdc_release_cooked_irq(hp_sdc_irqhook *callback) +{ + write_lock_irq(&hp_sdc.hook_lock); + if ((callback != hp_sdc.cooked) || + (hp_sdc.cooked == NULL)) { + write_unlock_irq(&hp_sdc.hook_lock); + return -EINVAL; + } + + hp_sdc.cooked = NULL; + /* Disable interrupts from HIL only if there is no raw HIL driver. */ + if(hp_sdc.hil == NULL) { + hp_sdc.im |= (HP_SDC_IM_HIL | HP_SDC_IM_RESET); + hp_sdc.set_im = 1; + } + write_unlock_irq(&hp_sdc.hook_lock); + tasklet_schedule(&hp_sdc.task); + + return 0; +} + +/************************* Keepalive timer task *********************/ + +static void hp_sdc_kicker(struct timer_list *unused) +{ + tasklet_schedule(&hp_sdc.task); + /* Re-insert the periodic task. */ + mod_timer(&hp_sdc.kicker, jiffies + HZ); +} + +/************************** Module Initialization ***************************/ + +#if defined(__hppa__) + +static const struct parisc_device_id hp_sdc_tbl[] __initconst = { + { + .hw_type = HPHW_FIO, + .hversion_rev = HVERSION_REV_ANY_ID, + .hversion = HVERSION_ANY_ID, + .sversion = 0x73, + }, + { 0, } +}; + +MODULE_DEVICE_TABLE(parisc, hp_sdc_tbl); + +static int __init hp_sdc_init_hppa(struct parisc_device *d); +static struct delayed_work moduleloader_work; + +static struct parisc_driver hp_sdc_driver __refdata = { + .name = "hp_sdc", + .id_table = hp_sdc_tbl, + .probe = hp_sdc_init_hppa, +}; + +#endif /* __hppa__ */ + +static int __init hp_sdc_init(void) +{ + char *errstr; + hp_sdc_transaction t_sync; + uint8_t ts_sync[6]; + struct semaphore s_sync; + + rwlock_init(&hp_sdc.lock); + rwlock_init(&hp_sdc.ibf_lock); + rwlock_init(&hp_sdc.rtq_lock); + rwlock_init(&hp_sdc.hook_lock); + + hp_sdc.timer = NULL; + hp_sdc.hil = NULL; + hp_sdc.pup = NULL; + hp_sdc.cooked = NULL; + hp_sdc.im = HP_SDC_IM_MASK; /* Mask maskable irqs */ + hp_sdc.set_im = 1; + hp_sdc.wi = 0xff; + hp_sdc.r7[0] = 0xff; + hp_sdc.r7[1] = 0xff; + hp_sdc.r7[2] = 0xff; + hp_sdc.r7[3] = 0xff; + hp_sdc.ibf = 1; + + memset(&hp_sdc.tq, 0, sizeof(hp_sdc.tq)); + + hp_sdc.wcurr = -1; + hp_sdc.rcurr = -1; + hp_sdc.rqty = 0; + + hp_sdc.dev_err = -ENODEV; + + errstr = "IO not found for"; + if (!hp_sdc.base_io) + goto err0; + + errstr = "IRQ not found for"; + if (!hp_sdc.irq) + goto err0; + + hp_sdc.dev_err = -EBUSY; + +#if defined(__hppa__) + errstr = "IO not available for"; + if (request_region(hp_sdc.data_io, 2, hp_sdc_driver.name)) + goto err0; +#endif + + errstr = "IRQ not available for"; + if (request_irq(hp_sdc.irq, &hp_sdc_isr, IRQF_SHARED, + "HP SDC", &hp_sdc)) + goto err1; + + errstr = "NMI not available for"; + if (request_irq(hp_sdc.nmi, &hp_sdc_nmisr, IRQF_SHARED, + "HP SDC NMI", &hp_sdc)) + goto err2; + + pr_info(PREFIX "HP SDC at 0x%08lx, IRQ %d (NMI IRQ %d)\n", + hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi); + + hp_sdc_status_in8(); + hp_sdc_data_in8(); + + tasklet_init(&hp_sdc.task, hp_sdc_tasklet, 0); + + /* Sync the output buffer registers, thus scheduling hp_sdc_tasklet. */ + t_sync.actidx = 0; + t_sync.idx = 1; + t_sync.endidx = 6; + t_sync.seq = ts_sync; + ts_sync[0] = HP_SDC_ACT_DATAREG | HP_SDC_ACT_SEMAPHORE; + ts_sync[1] = 0x0f; + ts_sync[2] = ts_sync[3] = ts_sync[4] = ts_sync[5] = 0; + t_sync.act.semaphore = &s_sync; + sema_init(&s_sync, 0); + hp_sdc_enqueue_transaction(&t_sync); + down(&s_sync); /* Wait for t_sync to complete */ + + /* Create the keepalive task */ + timer_setup(&hp_sdc.kicker, hp_sdc_kicker, 0); + hp_sdc.kicker.expires = jiffies + HZ; + add_timer(&hp_sdc.kicker); + + hp_sdc.dev_err = 0; + return 0; + err2: + free_irq(hp_sdc.irq, &hp_sdc); + err1: + release_region(hp_sdc.data_io, 2); + err0: + printk(KERN_WARNING PREFIX ": %s SDC IO=0x%p IRQ=0x%x NMI=0x%x\n", + errstr, (void *)hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi); + hp_sdc.dev = NULL; + + return hp_sdc.dev_err; +} + +#if defined(__hppa__) + +static void request_module_delayed(struct work_struct *work) +{ + request_module("hp_sdc_mlc"); +} + +static int __init hp_sdc_init_hppa(struct parisc_device *d) +{ + int ret; + + if (!d) + return 1; + if (hp_sdc.dev != NULL) + return 1; /* We only expect one SDC */ + + hp_sdc.dev = d; + hp_sdc.irq = d->irq; + hp_sdc.nmi = d->aux_irq; + hp_sdc.base_io = d->hpa.start; + hp_sdc.data_io = d->hpa.start + 0x800; + hp_sdc.status_io = d->hpa.start + 0x801; + + INIT_DELAYED_WORK(&moduleloader_work, request_module_delayed); + + ret = hp_sdc_init(); + /* after successful initialization give SDC some time to settle + * and then load the hp_sdc_mlc upper layer driver */ + if (!ret) + schedule_delayed_work(&moduleloader_work, + msecs_to_jiffies(2000)); + + return ret; +} + +#endif /* __hppa__ */ + +static void hp_sdc_exit(void) +{ + /* do nothing if we don't have a SDC */ + if (!hp_sdc.dev) + return; + + write_lock_irq(&hp_sdc.lock); + + /* Turn off all maskable "sub-function" irq's. */ + hp_sdc_spin_ibf(); + sdc_writeb(HP_SDC_CMD_SET_IM | HP_SDC_IM_MASK, hp_sdc.status_io); + + /* Wait until we know this has been processed by the i8042 */ + hp_sdc_spin_ibf(); + + free_irq(hp_sdc.nmi, &hp_sdc); + free_irq(hp_sdc.irq, &hp_sdc); + write_unlock_irq(&hp_sdc.lock); + + del_timer_sync(&hp_sdc.kicker); + + tasklet_kill(&hp_sdc.task); + +#if defined(__hppa__) + cancel_delayed_work_sync(&moduleloader_work); + if (unregister_parisc_driver(&hp_sdc_driver)) + printk(KERN_WARNING PREFIX "Error unregistering HP SDC"); +#endif +} + +static int __init hp_sdc_register(void) +{ + hp_sdc_transaction tq_init; + uint8_t tq_init_seq[5]; + struct semaphore tq_init_sem; +#if defined(__mc68000__) + unsigned char i; +#endif + + if (hp_sdc_disabled) { + printk(KERN_WARNING PREFIX "HP SDC driver disabled by no_hpsdc=1.\n"); + return -ENODEV; + } + + hp_sdc.dev = NULL; + hp_sdc.dev_err = 0; +#if defined(__hppa__) + if (register_parisc_driver(&hp_sdc_driver)) { + printk(KERN_WARNING PREFIX "Error registering SDC with system bus tree.\n"); + return -ENODEV; + } +#elif defined(__mc68000__) + if (!MACH_IS_HP300) + return -ENODEV; + + hp_sdc.irq = 1; + hp_sdc.nmi = 7; + hp_sdc.base_io = (unsigned long) 0xf0428000; + hp_sdc.data_io = (unsigned long) hp_sdc.base_io + 1; + hp_sdc.status_io = (unsigned long) hp_sdc.base_io + 3; + if (!copy_from_kernel_nofault(&i, (unsigned char *)hp_sdc.data_io, 1)) + hp_sdc.dev = (void *)1; + hp_sdc.dev_err = hp_sdc_init(); +#endif + if (hp_sdc.dev == NULL) { + printk(KERN_WARNING PREFIX "No SDC found.\n"); + return hp_sdc.dev_err; + } + + sema_init(&tq_init_sem, 0); + + tq_init.actidx = 0; + tq_init.idx = 1; + tq_init.endidx = 5; + tq_init.seq = tq_init_seq; + tq_init.act.semaphore = &tq_init_sem; + + tq_init_seq[0] = + HP_SDC_ACT_POSTCMD | HP_SDC_ACT_DATAIN | HP_SDC_ACT_SEMAPHORE; + tq_init_seq[1] = HP_SDC_CMD_READ_KCC; + tq_init_seq[2] = 1; + tq_init_seq[3] = 0; + tq_init_seq[4] = 0; + + hp_sdc_enqueue_transaction(&tq_init); + + down(&tq_init_sem); + up(&tq_init_sem); + + if ((tq_init_seq[0] & HP_SDC_ACT_DEAD) == HP_SDC_ACT_DEAD) { + printk(KERN_WARNING PREFIX "Error reading config byte.\n"); + hp_sdc_exit(); + return -ENODEV; + } + hp_sdc.r11 = tq_init_seq[4]; + if (hp_sdc.r11 & HP_SDC_CFG_NEW) { + const char *str; + printk(KERN_INFO PREFIX "New style SDC\n"); + tq_init_seq[1] = HP_SDC_CMD_READ_XTD; + tq_init.actidx = 0; + tq_init.idx = 1; + down(&tq_init_sem); + hp_sdc_enqueue_transaction(&tq_init); + down(&tq_init_sem); + up(&tq_init_sem); + if ((tq_init_seq[0] & HP_SDC_ACT_DEAD) == HP_SDC_ACT_DEAD) { + printk(KERN_WARNING PREFIX "Error reading extended config byte.\n"); + return -ENODEV; + } + hp_sdc.r7e = tq_init_seq[4]; + HP_SDC_XTD_REV_STRINGS(hp_sdc.r7e & HP_SDC_XTD_REV, str) + printk(KERN_INFO PREFIX "Revision: %s\n", str); + if (hp_sdc.r7e & HP_SDC_XTD_BEEPER) + printk(KERN_INFO PREFIX "TI SN76494 beeper present\n"); + if (hp_sdc.r7e & HP_SDC_XTD_BBRTC) + printk(KERN_INFO PREFIX "OKI MSM-58321 BBRTC present\n"); + printk(KERN_INFO PREFIX "Spunking the self test register to force PUP " + "on next firmware reset.\n"); + tq_init_seq[0] = HP_SDC_ACT_PRECMD | + HP_SDC_ACT_DATAOUT | HP_SDC_ACT_SEMAPHORE; + tq_init_seq[1] = HP_SDC_CMD_SET_STR; + tq_init_seq[2] = 1; + tq_init_seq[3] = 0; + tq_init.actidx = 0; + tq_init.idx = 1; + tq_init.endidx = 4; + down(&tq_init_sem); + hp_sdc_enqueue_transaction(&tq_init); + down(&tq_init_sem); + up(&tq_init_sem); + } else + printk(KERN_INFO PREFIX "Old style SDC (1820-%s).\n", + (hp_sdc.r11 & HP_SDC_CFG_REV) ? "3300" : "2564/3087"); + + return 0; +} + +module_init(hp_sdc_register); +module_exit(hp_sdc_exit); + +/* Timing notes: These measurements taken on my 64MHz 7100-LC (715/64) + * cycles cycles-adj time + * between two consecutive mfctl(16)'s: 4 n/a 63ns + * hp_sdc_spin_ibf when idle: 119 115 1.7us + * gsc_writeb status register: 83 79 1.2us + * IBF to clear after sending SET_IM: 6204 6006 93us + * IBF to clear after sending LOAD_RT: 4467 4352 68us + * IBF to clear after sending two LOAD_RTs: 18974 18859 295us + * READ_T1, read status/data, IRQ, call handler: 35564 n/a 556us + * cmd to ~IBF READ_T1 2nd time right after: 5158403 n/a 81ms + * between IRQ received and ~IBF for above: 2578877 n/a 40ms + * + * Performance stats after a run of this module configuring HIL and + * receiving a few mouse events: + * + * status in8 282508 cycles 7128 calls + * status out8 8404 cycles 341 calls + * data out8 1734 cycles 78 calls + * isr 174324 cycles 617 calls (includes take) + * take 1241 cycles 2 calls + * put 1411504 cycles 6937 calls + * task 1655209 cycles 6937 calls (includes put) + * + */ |