diff options
Diffstat (limited to 'drivers/scsi/wd33c93.h')
| -rw-r--r-- | drivers/scsi/wd33c93.h | 342 |
1 files changed, 342 insertions, 0 deletions
diff --git a/drivers/scsi/wd33c93.h b/drivers/scsi/wd33c93.h new file mode 100644 index 000000000..2edec34c5 --- /dev/null +++ b/drivers/scsi/wd33c93.h @@ -0,0 +1,342 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * wd33c93.h - Linux device driver definitions for the + * Commodore Amiga A2091/590 SCSI controller card + * + * IMPORTANT: This file is for version 1.25 - 09/Jul/1997 + * + * Copyright (c) 1996 John Shifflett, GeoLog Consulting + * john@geolog.com + * jshiffle@netcom.com + */ +#ifndef WD33C93_H +#define WD33C93_H + + +#define PROC_INTERFACE /* add code for /proc/scsi/wd33c93/xxx interface */ +#ifdef PROC_INTERFACE +#define PROC_STATISTICS /* add code for keeping various real time stats */ +#endif + +#define SYNC_DEBUG /* extra info on sync negotiation printed */ +#define DEBUGGING_ON /* enable command-line debugging bitmask */ +#define DEBUG_DEFAULTS 0 /* default debugging bitmask */ + + +#ifdef DEBUGGING_ON +#define DB(f,a) if (hostdata->args & (f)) a; +#else +#define DB(f,a) +#endif + +#define uchar unsigned char + + +/* wd register names */ +#define WD_OWN_ID 0x00 +#define WD_CONTROL 0x01 +#define WD_TIMEOUT_PERIOD 0x02 +#define WD_CDB_1 0x03 +#define WD_CDB_2 0x04 +#define WD_CDB_3 0x05 +#define WD_CDB_4 0x06 +#define WD_CDB_5 0x07 +#define WD_CDB_6 0x08 +#define WD_CDB_7 0x09 +#define WD_CDB_8 0x0a +#define WD_CDB_9 0x0b +#define WD_CDB_10 0x0c +#define WD_CDB_11 0x0d +#define WD_CDB_12 0x0e +#define WD_TARGET_LUN 0x0f +#define WD_COMMAND_PHASE 0x10 +#define WD_SYNCHRONOUS_TRANSFER 0x11 +#define WD_TRANSFER_COUNT_MSB 0x12 +#define WD_TRANSFER_COUNT 0x13 +#define WD_TRANSFER_COUNT_LSB 0x14 +#define WD_DESTINATION_ID 0x15 +#define WD_SOURCE_ID 0x16 +#define WD_SCSI_STATUS 0x17 +#define WD_COMMAND 0x18 +#define WD_DATA 0x19 +#define WD_QUEUE_TAG 0x1a +#define WD_AUXILIARY_STATUS 0x1f + +/* WD commands */ +#define WD_CMD_RESET 0x00 +#define WD_CMD_ABORT 0x01 +#define WD_CMD_ASSERT_ATN 0x02 +#define WD_CMD_NEGATE_ACK 0x03 +#define WD_CMD_DISCONNECT 0x04 +#define WD_CMD_RESELECT 0x05 +#define WD_CMD_SEL_ATN 0x06 +#define WD_CMD_SEL 0x07 +#define WD_CMD_SEL_ATN_XFER 0x08 +#define WD_CMD_SEL_XFER 0x09 +#define WD_CMD_RESEL_RECEIVE 0x0a +#define WD_CMD_RESEL_SEND 0x0b +#define WD_CMD_WAIT_SEL_RECEIVE 0x0c +#define WD_CMD_TRANS_ADDR 0x18 +#define WD_CMD_TRANS_INFO 0x20 +#define WD_CMD_TRANSFER_PAD 0x21 +#define WD_CMD_SBT_MODE 0x80 + +/* ASR register */ +#define ASR_INT (0x80) +#define ASR_LCI (0x40) +#define ASR_BSY (0x20) +#define ASR_CIP (0x10) +#define ASR_PE (0x02) +#define ASR_DBR (0x01) + +/* SCSI Bus Phases */ +#define PHS_DATA_OUT 0x00 +#define PHS_DATA_IN 0x01 +#define PHS_COMMAND 0x02 +#define PHS_STATUS 0x03 +#define PHS_MESS_OUT 0x06 +#define PHS_MESS_IN 0x07 + +/* Command Status Register definitions */ + + /* reset state interrupts */ +#define CSR_RESET 0x00 +#define CSR_RESET_AF 0x01 + + /* successful completion interrupts */ +#define CSR_RESELECT 0x10 +#define CSR_SELECT 0x11 +#define CSR_SEL_XFER_DONE 0x16 +#define CSR_XFER_DONE 0x18 + + /* paused or aborted interrupts */ +#define CSR_MSGIN 0x20 +#define CSR_SDP 0x21 +#define CSR_SEL_ABORT 0x22 +#define CSR_RESEL_ABORT 0x25 +#define CSR_RESEL_ABORT_AM 0x27 +#define CSR_ABORT 0x28 + + /* terminated interrupts */ +#define CSR_INVALID 0x40 +#define CSR_UNEXP_DISC 0x41 +#define CSR_TIMEOUT 0x42 +#define CSR_PARITY 0x43 +#define CSR_PARITY_ATN 0x44 +#define CSR_BAD_STATUS 0x45 +#define CSR_UNEXP 0x48 + + /* service required interrupts */ +#define CSR_RESEL 0x80 +#define CSR_RESEL_AM 0x81 +#define CSR_DISC 0x85 +#define CSR_SRV_REQ 0x88 + + /* Own ID/CDB Size register */ +#define OWNID_EAF 0x08 +#define OWNID_EHP 0x10 +#define OWNID_RAF 0x20 +#define OWNID_FS_8 0x00 +#define OWNID_FS_12 0x40 +#define OWNID_FS_16 0x80 + + /* define these so we don't have to change a2091.c, etc. */ +#define WD33C93_FS_8_10 OWNID_FS_8 +#define WD33C93_FS_12_15 OWNID_FS_12 +#define WD33C93_FS_16_20 OWNID_FS_16 + + /* pass input-clock explicitly. accepted mhz values are 8-10,12-20 */ +#define WD33C93_FS_MHZ(mhz) (mhz) + + /* Control register */ +#define CTRL_HSP 0x01 +#define CTRL_HA 0x02 +#define CTRL_IDI 0x04 +#define CTRL_EDI 0x08 +#define CTRL_HHP 0x10 +#define CTRL_POLLED 0x00 +#define CTRL_BURST 0x20 +#define CTRL_BUS 0x40 +#define CTRL_DMA 0x80 + + /* Timeout Period register */ +#define TIMEOUT_PERIOD_VALUE 20 /* 20 = 200 ms */ + + /* Synchronous Transfer Register */ +#define STR_FSS 0x80 + + /* Destination ID register */ +#define DSTID_DPD 0x40 +#define DATA_OUT_DIR 0 +#define DATA_IN_DIR 1 +#define DSTID_SCC 0x80 + + /* Source ID register */ +#define SRCID_MASK 0x07 +#define SRCID_SIV 0x08 +#define SRCID_DSP 0x20 +#define SRCID_ES 0x40 +#define SRCID_ER 0x80 + + /* This is what the 3393 chip looks like to us */ +typedef struct { +#ifdef CONFIG_WD33C93_PIO + unsigned int SASR; + unsigned int SCMD; +#else + volatile unsigned char *SASR; + volatile unsigned char *SCMD; +#endif +} wd33c93_regs; + + +typedef int (*dma_setup_t) (struct scsi_cmnd *SCpnt, int dir_in); +typedef void (*dma_stop_t) (struct Scsi_Host *instance, + struct scsi_cmnd *SCpnt, int status); + + +#define ILLEGAL_STATUS_BYTE 0xff + +#define DEFAULT_SX_PER 376 /* (ns) fairly safe */ +#define DEFAULT_SX_OFF 0 /* aka async */ + +#define OPTIMUM_SX_PER 252 /* (ns) best we can do (mult-of-4) */ +#define OPTIMUM_SX_OFF 12 /* size of wd3393 fifo */ + +struct sx_period { + unsigned int period_ns; + uchar reg_value; + }; + +/* FEF: defines for hostdata->dma_buffer_pool */ + +#define BUF_CHIP_ALLOCED 0 +#define BUF_SCSI_ALLOCED 1 + +struct WD33C93_hostdata { + struct Scsi_Host *next; + wd33c93_regs regs; + spinlock_t lock; + uchar clock_freq; + uchar chip; /* what kind of wd33c93? */ + uchar microcode; /* microcode rev */ + uchar dma_buffer_pool; /* FEF: buffer from chip_ram? */ + int dma_dir; /* data transfer dir. */ + dma_setup_t dma_setup; + dma_stop_t dma_stop; + unsigned int dma_xfer_mask; + uchar *dma_bounce_buffer; + unsigned int dma_bounce_len; + volatile uchar busy[8]; /* index = target, bit = lun */ + volatile struct scsi_cmnd *input_Q; /* commands waiting to be started */ + volatile struct scsi_cmnd *selecting; /* trying to select this command */ + volatile struct scsi_cmnd *connected; /* currently connected command */ + volatile struct scsi_cmnd *disconnected_Q;/* commands waiting for reconnect */ + uchar state; /* what we are currently doing */ + uchar dma; /* current state of DMA (on/off) */ + uchar level2; /* extent to which Level-2 commands are used */ + uchar disconnect; /* disconnect/reselect policy */ + unsigned int args; /* set from command-line argument */ + uchar incoming_msg[8]; /* filled during message_in phase */ + int incoming_ptr; /* mainly used with EXTENDED messages */ + uchar outgoing_msg[8]; /* send this during next message_out */ + int outgoing_len; /* length of outgoing message */ + unsigned int default_sx_per; /* default transfer period for SCSI bus */ + uchar sync_xfer[8]; /* sync_xfer reg settings per target */ + uchar sync_stat[8]; /* status of sync negotiation per target */ + uchar no_sync; /* bitmask: don't do sync on these targets */ + uchar no_dma; /* set this flag to disable DMA */ + uchar dma_mode; /* DMA Burst Mode or Single Byte DMA */ + uchar fast; /* set this flag to enable Fast SCSI */ + struct sx_period sx_table[9]; /* transfer periods for actual DTC-setting */ +#ifdef PROC_INTERFACE + uchar proc; /* bitmask: what's in proc output */ +#ifdef PROC_STATISTICS + unsigned long cmd_cnt[8]; /* # of commands issued per target */ + unsigned long int_cnt; /* # of interrupts serviced */ + unsigned long pio_cnt; /* # of pio data transfers */ + unsigned long dma_cnt; /* # of DMA data transfers */ + unsigned long disc_allowed_cnt[8]; /* # of disconnects allowed per target */ + unsigned long disc_done_cnt[8]; /* # of disconnects done per target*/ +#endif +#endif + }; + + +/* defines for hostdata->chip */ + +#define C_WD33C93 0 +#define C_WD33C93A 1 +#define C_WD33C93B 2 +#define C_UNKNOWN_CHIP 100 + +/* defines for hostdata->state */ + +#define S_UNCONNECTED 0 +#define S_SELECTING 1 +#define S_RUNNING_LEVEL2 2 +#define S_CONNECTED 3 +#define S_PRE_TMP_DISC 4 +#define S_PRE_CMP_DISC 5 + +/* defines for hostdata->dma */ + +#define D_DMA_OFF 0 +#define D_DMA_RUNNING 1 + +/* defines for hostdata->level2 */ +/* NOTE: only the first 3 are implemented so far */ + +#define L2_NONE 1 /* no combination commands - we get lots of ints */ +#define L2_SELECT 2 /* start with SEL_ATN_XFER, but never resume it */ +#define L2_BASIC 3 /* resume after STATUS ints & RDP messages */ +#define L2_DATA 4 /* resume after DATA_IN/OUT ints */ +#define L2_MOST 5 /* resume after anything except a RESELECT int */ +#define L2_RESELECT 6 /* resume after everything, including RESELECT ints */ +#define L2_ALL 7 /* always resume */ + +/* defines for hostdata->disconnect */ + +#define DIS_NEVER 0 +#define DIS_ADAPTIVE 1 +#define DIS_ALWAYS 2 + +/* defines for hostdata->args */ + +#define DB_TEST1 1<<0 +#define DB_TEST2 1<<1 +#define DB_QUEUE_COMMAND 1<<2 +#define DB_EXECUTE 1<<3 +#define DB_INTR 1<<4 +#define DB_TRANSFER 1<<5 +#define DB_MASK 0x3f + +/* defines for hostdata->sync_stat[] */ + +#define SS_UNSET 0 +#define SS_FIRST 1 +#define SS_WAITING 2 +#define SS_SET 3 + +/* defines for hostdata->proc */ + +#define PR_VERSION 1<<0 +#define PR_INFO 1<<1 +#define PR_STATISTICS 1<<2 +#define PR_CONNECTED 1<<3 +#define PR_INPUTQ 1<<4 +#define PR_DISCQ 1<<5 +#define PR_TEST 1<<6 +#define PR_STOP 1<<7 + + +void wd33c93_init (struct Scsi_Host *instance, const wd33c93_regs regs, + dma_setup_t setup, dma_stop_t stop, int clock_freq); +int wd33c93_abort (struct scsi_cmnd *cmd); +int wd33c93_queuecommand (struct Scsi_Host *h, struct scsi_cmnd *cmd); +void wd33c93_intr (struct Scsi_Host *instance); +int wd33c93_show_info(struct seq_file *, struct Scsi_Host *); +int wd33c93_write_info(struct Scsi_Host *, char *, int); +int wd33c93_host_reset (struct scsi_cmnd *); + +#endif /* WD33C93_H */ |