Adding upstream version 2.10.0+dfsg.upstream/2.10.0+dfsgupstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

100 files changed, 11808 insertions, 0 deletions

diff --git a/plat/marvell/armada/a3k/a3700/board/pm_src.c b/plat/marvell/armada/a3k/a3700/board/pm_src.c
new file mode 100644
index 0000000..247f73b
--- /dev/null
+++ b/plat/marvell/armada/a3k/a3700/board/pm_src.c
@@ -0,0 +1,37 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <a3700_pm.h>
+#include <plat_marvell.h>
+
+/* This struct provides the PM wake up src configuration for A3720 Development Board */
+static struct pm_wake_up_src_config wake_up_src_cfg = {
+	.wake_up_src_num = 3,
+	.wake_up_src[0] = {
+		.wake_up_src_type = WAKE_UP_SRC_GPIO,
+		.wake_up_data = {
+			.gpio_data.bank_num = 0, /* North Bridge */
+			.gpio_data.gpio_num = 14
+		}
+	},
+	.wake_up_src[1] = {
+		.wake_up_src_type = WAKE_UP_SRC_GPIO,
+		.wake_up_data = {
+			.gpio_data.bank_num = 1, /* South Bridge */
+			.gpio_data.gpio_num = 2
+		}
+	},
+	.wake_up_src[2] = {
+		.wake_up_src_type = WAKE_UP_SRC_UART1,
+	}
+};
+
+struct pm_wake_up_src_config *mv_wake_up_src_config_get(void)
+{
+	return &wake_up_src_cfg;
+}
+
diff --git a/plat/marvell/armada/a3k/a3700/mvebu_def.h b/plat/marvell/armada/a3k/a3700/mvebu_def.h
new file mode 100644
index 0000000..dad1085
--- /dev/null
+++ b/plat/marvell/armada/a3k/a3700/mvebu_def.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a3700_plat_def.h>
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a3k/a3700/plat_bl31_setup.c b/plat/marvell/armada/a3k/a3700/plat_bl31_setup.c
new file mode 100644
index 0000000..6862a86
--- /dev/null
+++ b/plat/marvell/armada/a3k/a3700/plat_bl31_setup.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+#include <dram_win.h>
+#include <io_addr_dec.h>
+#include <marvell_plat_priv.h>
+#include <plat_marvell.h>
+
+/* This routine does MPP initialization */
+static void marvell_bl31_mpp_init(void)
+{
+	mmio_clrbits_32(MVEBU_NB_GPIO_SEL_REG, 1 << MVEBU_GPIO_TW1_GPIO_EN_OFF);
+
+	/* Set hidden GPIO setting for SPI.
+	 * In north_bridge_pin_out_en_high register 13804,
+	 * bit 28 is the one which enables CS, CLK pins to be
+	 * output, need to set it to 1.
+	 * The initial value of this bit is 1, but in UART boot mode
+	 * initialization, this bit is disabled and the SPI CS and CLK pins
+	 * are used for downloading image purpose; so after downloading,
+	 * we should set this bit to 1 again to enable SPI CS and CLK pins.
+	 * And anyway, this bit value should be 1 in all modes,
+	 * so here we does not judge boot mode and set this bit to 1 always.
+	 */
+	mmio_setbits_32(MVEBU_NB_GPIO_OUTPUT_EN_HIGH_REG,
+			1 << MVEBU_GPIO_NB_SPI_PIN_MODE_OFF);
+}
+
+/* This function overruns the same function in marvell_bl31_setup.c */
+void bl31_plat_arch_setup(void)
+{
+	struct dec_win_config *io_dec_map;
+	uint32_t dec_win_num;
+	struct dram_win_map dram_wins_map;
+
+	marvell_bl31_plat_arch_setup();
+
+	/* MPP init */
+	marvell_bl31_mpp_init();
+
+	/* initialize the timer for delay functionality */
+	plat_delay_timer_init();
+
+	/* CPU address decoder windows initialization. */
+	cpu_wins_init();
+
+	/* fetch CPU-DRAM window mapping information by reading
+	 * CPU-DRAM decode windows (only the enabled ones)
+	 */
+	dram_win_map_build(&dram_wins_map);
+
+	/* Get IO address decoder windows */
+	if (marvell_get_io_dec_win_conf(&io_dec_map, &dec_win_num)) {
+		printf("No IO address decoder windows configurations found!\n");
+		return;
+	}
+
+	/* IO address decoder init */
+	if (init_io_addr_dec(&dram_wins_map, io_dec_map, dec_win_num)) {
+		printf("IO address decoder windows initialization failed!\n");
+		return;
+	}
+}
diff --git a/plat/marvell/armada/a3k/a3700/platform.mk b/plat/marvell/armada/a3k/a3700/platform.mk
new file mode 100644
index 0000000..050af41
--- /dev/null
+++ b/plat/marvell/armada/a3k/a3700/platform.mk
@@ -0,0 +1,10 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:	BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+include plat/marvell/armada/a3k/common/a3700_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a3k/common/a3700_common.mk b/plat/marvell/armada/a3k/common/a3700_common.mk
new file mode 100644
index 0000000..b9c28de
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/a3700_common.mk
@@ -0,0 +1,247 @@
+#
+# Copyright (C) 2018-2021 Marvell International Ltd.
+#
+# SPDX-License-Identifier:	BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+MARVELL_PLAT_BASE		:= plat/marvell/armada
+MARVELL_PLAT_INCLUDE_BASE	:= include/plat/marvell/armada
+PLAT_FAMILY			:= a3k
+PLAT_FAMILY_BASE		:= $(MARVELL_PLAT_BASE)/$(PLAT_FAMILY)
+PLAT_INCLUDE_BASE		:= $(MARVELL_PLAT_INCLUDE_BASE)/$(PLAT_FAMILY)
+PLAT_COMMON_BASE		:= $(PLAT_FAMILY_BASE)/common
+MARVELL_DRV_BASE		:= drivers/marvell
+MARVELL_COMMON_BASE		:= $(MARVELL_PLAT_BASE)/common
+ERRATA_A53_1530924		:= 1
+
+include plat/marvell/marvell.mk
+
+#*********** A3700 *************
+
+# GICV3
+$(eval $(call add_define,CONFIG_GICV3))
+
+# CCI-400
+$(eval $(call add_define,USE_CCI))
+
+# Include GICv3 driver files
+include drivers/arm/gic/v3/gicv3.mk
+
+MARVELL_GIC_SOURCES	:=	${GICV3_SOURCES}			\
+				plat/common/plat_gicv3.c
+
+PLAT_INCLUDES		:=	-I$(PLAT_FAMILY_BASE)/$(PLAT)		\
+				-I$(PLAT_COMMON_BASE)/include		\
+				-I$(PLAT_INCLUDE_BASE)/common		\
+				-I$(MARVELL_DRV_BASE)			\
+				-I$/drivers/arm/gic/common/
+
+PLAT_BL_COMMON_SOURCES	:=	$(PLAT_COMMON_BASE)/aarch64/a3700_common.c \
+				$(PLAT_COMMON_BASE)/aarch64/a3700_clock.S \
+				$(MARVELL_DRV_BASE)/uart/a3700_console.S
+
+BL1_SOURCES		+=	$(PLAT_COMMON_BASE)/aarch64/plat_helpers.S \
+				lib/cpus/aarch64/cortex_a53.S
+
+MARVELL_DRV		:=	$(MARVELL_DRV_BASE)/comphy/phy-comphy-3700.c
+
+BL31_SOURCES		+=	lib/cpus/aarch64/cortex_a53.S		\
+				$(PLAT_COMMON_BASE)/aarch64/plat_helpers.S \
+				$(PLAT_COMMON_BASE)/plat_cci.c		\
+				$(PLAT_COMMON_BASE)/plat_pm.c		\
+				$(PLAT_COMMON_BASE)/dram_win.c		\
+				$(PLAT_COMMON_BASE)/io_addr_dec.c	\
+				$(PLAT_COMMON_BASE)/marvell_plat_config.c     \
+				$(PLAT_FAMILY_BASE)/$(PLAT)/plat_bl31_setup.c \
+				$(MARVELL_COMMON_BASE)/marvell_cci.c	\
+				$(MARVELL_COMMON_BASE)/marvell_ddr_info.c	\
+				$(MARVELL_COMMON_BASE)/marvell_gicv3.c	\
+				$(MARVELL_GIC_SOURCES)			\
+				drivers/arm/cci/cci.c			\
+				$(PLAT_COMMON_BASE)/a3700_sip_svc.c	\
+				$(MARVELL_DRV)
+
+ifeq ($(HANDLE_EA_EL3_FIRST_NS),1)
+BL31_SOURCES		+=	$(PLAT_COMMON_BASE)/a3700_ea.c
+endif
+
+ifeq ($(CM3_SYSTEM_RESET),1)
+BL31_SOURCES		+=	$(PLAT_COMMON_BASE)/cm3_system_reset.c
+endif
+
+ifeq ($(A3720_DB_PM_WAKEUP_SRC),1)
+BL31_SOURCES		+=	$(PLAT_FAMILY_BASE)/$(PLAT)/board/pm_src.c
+endif
+
+ifdef WTP
+
+# Do not remove! Following checks are required to ensure correct TF-A builds, removing these checks leads to broken TF-A builds
+$(if $(wildcard $(value WTP)/*),,$(error "'WTP=$(value WTP)' was specified, but '$(value WTP)' directory does not exist"))
+$(if $(shell git -C $(value WTP) rev-parse --show-cdup 2>&1),$(error "'WTP=$(value WTP)' was specified, but '$(value WTP)' does not contain valid A3700-utils-marvell git repository"))
+
+TBB		:= $(WTP)/wtptp/src/TBB_Linux/release/TBB_linux
+
+BUILD_UART	:= uart-images
+UART_IMAGE	:= $(BUILD_UART).tgz.bin
+
+ifeq ($(MARVELL_SECURE_BOOT),1)
+TIM_CFG		:= $(BUILD_PLAT)/atf-tim.txt
+TIM_UART_CFG	:= $(BUILD_PLAT)/$(BUILD_UART)/atf-tim.txt
+IMAGESPATH	:= $(WTP)/tim/trusted
+TIMN_CFG	:= $(BUILD_PLAT)/atf-timN.txt
+TIMN_UART_CFG	:= $(BUILD_PLAT)/$(BUILD_UART)/atf-timN.txt
+TIMN_SIG	:= $(IMAGESPATH)/timnsign.txt
+TIM2IMGARGS	:= -i $(TIM_CFG) -n $(TIMN_CFG)
+TIMN_UART_IMAGE	:= $$(grep "Image Filename:" -m 1 $(TIMN_UART_CFG) | cut -c 17-)
+else #MARVELL_SECURE_BOOT
+TIM_CFG		:= $(BUILD_PLAT)/atf-ntim.txt
+TIM_UART_CFG	:= $(BUILD_PLAT)/$(BUILD_UART)/atf-ntim.txt
+IMAGESPATH	:= $(WTP)/tim/untrusted
+TIM2IMGARGS	:= -i $(TIM_CFG)
+endif #MARVELL_SECURE_BOOT
+
+TIM_UART_IMAGE	:= $$(grep "Image Filename:" -m 1 $(TIM_UART_CFG) | cut -c 17-)
+
+TIMBUILD	:= $(WTP)/script/buildtim.sh
+TIM2IMG		:= $(WTP)/script/tim2img.pl
+TIMDDRTOOL	:= $(WTP)/tim/ddr/ddr_tool
+
+$(TIMBUILD): $(TIMDDRTOOL)
+
+# WTMI_IMG is used to specify the customized RTOS image running over
+# Service CPU (CM3 processor). By the default, it points to a
+# baremetal binary of fuse programming in A3700_utils.
+WTMI_IMG	:= $(WTP)/wtmi/fuse/build/fuse.bin
+
+# WTMI_MULTI_IMG is composed of CM3 RTOS image (WTMI_IMG)
+# and sys-init image.
+WTMI_MULTI_IMG		:= $(WTP)/wtmi/build/wtmi.bin
+
+WTMI_ENC_IMG		:= wtmi-enc.bin
+
+SRCPATH			:= $(dir $(BL33))
+
+CLOCKSPRESET		?= CPU_800_DDR_800
+
+DDR_TOPOLOGY		?= 0
+
+BOOTDEV			?= SPINOR
+PARTNUM			?= 0
+
+TIMBLDARGS		:= $(MARVELL_SECURE_BOOT) $(BOOTDEV) $(IMAGESPATH) $(WTP) $(CLOCKSPRESET) \
+				$(DDR_TOPOLOGY) $(PARTNUM) $(DEBUG) $(TIM_CFG) $(TIMN_CFG) $(TIMN_SIG) 1
+TIMBLDUARTARGS		:= $(MARVELL_SECURE_BOOT) UART $(IMAGESPATH) $(WTP) $(CLOCKSPRESET) \
+				$(DDR_TOPOLOGY) 0 0 $(TIM_UART_CFG) $(TIMN_UART_CFG) $(TIMN_SIG) 0
+
+UART_IMAGES		:= $(BUILD_UART)/$(TIM_UART_IMAGE)
+ifeq ($(MARVELL_SECURE_BOOT),1)
+UART_IMAGES		+= $(BUILD_UART)/$(TIMN_UART_IMAGE)
+endif
+UART_IMAGES		+= $(BUILD_UART)/wtmi_h.bin $(BUILD_UART)/boot-image_h.bin
+
+CRYPTOPP_LIBDIR		?= $(CRYPTOPP_PATH)
+CRYPTOPP_INCDIR		?= $(CRYPTOPP_PATH)
+
+$(TBB): FORCE
+#	Do not remove! Following checks are required to ensure correct TF-A builds, removing these checks leads to broken TF-A builds
+	$(if $(CRYPTOPP_LIBDIR),,$(error "Platform '$(PLAT)' for WTP image tool requires CRYPTOPP_PATH or CRYPTOPP_LIBDIR. Please set CRYPTOPP_PATH or CRYPTOPP_LIBDIR to point to the right directory"))
+	$(if $(CRYPTOPP_INCDIR),,$(error "Platform '$(PLAT)' for WTP image tool requires CRYPTOPP_PATH or CRYPTOPP_INCDIR. Please set CRYPTOPP_PATH or CRYPTOPP_INCDIR to point to the right directory"))
+	$(if $(wildcard $(CRYPTOPP_LIBDIR)/*),,$(error "Either 'CRYPTOPP_PATH' or 'CRYPTOPP_LIB' was set to '$(CRYPTOPP_LIBDIR)', but '$(CRYPTOPP_LIBDIR)' does not exist"))
+	$(if $(wildcard $(CRYPTOPP_INCDIR)/*),,$(error "Either 'CRYPTOPP_PATH' or 'CRYPTOPP_INCDIR' was set to '$(CRYPTOPP_INCDIR)', but '$(CRYPTOPP_INCDIR)' does not exist"))
+ifdef CRYPTOPP_PATH
+	$(Q)$(MAKE) --no-print-directory -C $(CRYPTOPP_PATH) -f GNUmakefile
+endif
+	$(Q)$(MAKE) --no-print-directory -C $(WTP)/wtptp/src/TBB_Linux -f TBB_linux.mak LIBDIR=$(CRYPTOPP_LIBDIR) INCDIR=$(CRYPTOPP_INCDIR)
+
+$(WTMI_MULTI_IMG): FORCE
+	$(Q)$(MAKE) --no-print-directory -C $(WTP) WTMI_IMG=$(WTMI_IMG) DDR_TOPOLOGY=$(DDR_TOPOLOGY) CLOCKSPRESET=$(CLOCKSPRESET) WTMI
+
+$(BUILD_PLAT)/wtmi.bin: $(WTMI_MULTI_IMG)
+	$(Q)cp -a $(WTMI_MULTI_IMG) $(BUILD_PLAT)/wtmi.bin
+
+$(TIMDDRTOOL): FORCE
+#	Do not remove! Following checks are required to ensure correct TF-A builds, removing these checks leads to broken TF-A builds
+	$(if $(value MV_DDR_PATH),,$(error "Platform '${PLAT}' for ddr tool requires MV_DDR_PATH. Please set MV_DDR_PATH to point to the right directory"))
+	$(if $(wildcard $(value MV_DDR_PATH)/*),,$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' directory does not exist"))
+	$(if $(shell git -C $(value MV_DDR_PATH) rev-parse --show-cdup 2>&1),$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' does not contain valid mv-ddr-marvell git repository"))
+	$(Q)$(MAKE) --no-print-directory -C $(WTP) MV_DDR_PATH=$(MV_DDR_PATH) DDR_TOPOLOGY=$(DDR_TOPOLOGY) mv_ddr
+
+$(BUILD_PLAT)/$(UART_IMAGE): $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/wtmi.bin $(TBB) $(TIMBUILD) $(TIMDDRTOOL)
+	@$(ECHO_BLANK_LINE)
+	@echo "Building uart images"
+	$(Q)mkdir -p $(BUILD_PLAT)/$(BUILD_UART)
+	$(Q)cp -a $(BUILD_PLAT)/wtmi.bin $(BUILD_PLAT)/$(BUILD_UART)/wtmi.bin
+	$(Q)cp -a $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/$(BUILD_UART)/$(BOOT_IMAGE)
+	$(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(TIMBUILD) $(TIMBLDUARTARGS)
+	$(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIM_UART_CFG)
+	$(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIM_UART_CFG)
+ifeq ($(MARVELL_SECURE_BOOT),1)
+	$(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIMN_UART_CFG)
+	$(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIMN_UART_CFG)
+endif
+	$(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(TBB) -r $(TIM_UART_CFG) -v -D
+ifeq ($(MARVELL_SECURE_BOOT),1)
+	$(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(TBB) -r $(TIMN_UART_CFG)
+endif
+	$(Q)tar czf $(BUILD_PLAT)/$(UART_IMAGE) -C $(BUILD_PLAT) $(UART_IMAGES)
+	@$(ECHO_BLANK_LINE)
+	@echo "Built $@ successfully"
+	@$(ECHO_BLANK_LINE)
+
+$(BUILD_PLAT)/$(FLASH_IMAGE): $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/wtmi.bin $(TBB) $(TIMBUILD) $(TIMDDRTOOL) $(TIM2IMG)
+	@$(ECHO_BLANK_LINE)
+	@echo "Building flash image"
+	$(Q)cd $(BUILD_PLAT) && $(TIMBUILD) $(TIMBLDARGS)
+	$(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIM_CFG)
+	$(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIM_CFG)
+ifeq ($(MARVELL_SECURE_BOOT),1)
+	$(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIMN_CFG)
+	$(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIMN_CFG)
+	@$(ECHO_BLANK_LINE)
+	@echo "=======================================================";
+	@echo "  Secure boot. Encrypting wtmi and boot-image";
+	@echo "=======================================================";
+	@$(ECHO_BLANK_LINE)
+	$(Q)cp $(BUILD_PLAT)/wtmi.bin $(BUILD_PLAT)/wtmi-align.bin
+	$(Q)truncate -s %16 $(BUILD_PLAT)/wtmi-align.bin
+	$(Q)${OPENSSL_BIN_PATH}/openssl enc -aes-256-cbc -e -in $(BUILD_PLAT)/wtmi-align.bin \
+	-out $(BUILD_PLAT)/$(WTMI_ENC_IMG) \
+	-K `cat $(IMAGESPATH)/aes-256.txt` -nosalt \
+	-iv `cat $(IMAGESPATH)/iv.txt` -p
+	$(Q)truncate -s %16 $(BUILD_PLAT)/$(BOOT_IMAGE);
+	$(Q)${OPENSSL_BIN_PATH}/openssl enc -aes-256-cbc -e -in $(BUILD_PLAT)/$(BOOT_IMAGE) \
+	-out $(BUILD_PLAT)/$(BOOT_ENC_IMAGE) \
+	-K `cat $(IMAGESPATH)/aes-256.txt` -nosalt \
+	-iv `cat $(IMAGESPATH)/iv.txt` -p
+endif
+	$(Q)cd $(BUILD_PLAT) && $(TBB) -r $(TIM_CFG) -v -D
+ifeq ($(MARVELL_SECURE_BOOT),1)
+	$(Q)cd $(BUILD_PLAT) && $(TBB) -r $(TIMN_CFG)
+	$(Q)sed -i 's|wtmi.bin|$(WTMI_ENC_IMG)|1' $(TIMN_CFG)
+	$(Q)sed -i 's|$(BOOT_IMAGE)|$(BOOT_ENC_IMAGE)|1' $(TIMN_CFG)
+endif
+	$(Q)cd $(BUILD_PLAT) && $(TIM2IMG) $(TIM2IMGARGS) -o $(BUILD_PLAT)/$(FLASH_IMAGE)
+	@$(ECHO_BLANK_LINE)
+	@echo "Built $@ successfully"
+	@$(ECHO_BLANK_LINE)
+
+clean realclean distclean: mrvl_clean
+
+.PHONY: mrvl_clean
+mrvl_clean:
+	-$(Q)$(MAKE) --no-print-directory -C $(WTP) MV_DDR_PATH=$(MV_DDR_PATH) clean
+	-$(Q)$(MAKE) --no-print-directory -C $(WTP)/wtptp/src/TBB_Linux -f TBB_linux.mak clean
+ifdef CRYPTOPP_PATH
+	-$(Q)$(MAKE) --no-print-directory -C $(CRYPTOPP_PATH) -f GNUmakefile clean
+endif
+
+else # WTP
+
+$(BUILD_PLAT)/$(UART_IMAGE) $(BUILD_PLAT)/$(FLASH_IMAGE):
+	$(error "Platform '${PLAT}' for target '$@' requires WTP. Please set WTP to point to the right directory")
+
+endif # WTP
+
+.PHONY: mrvl_uart
+mrvl_uart: $(BUILD_PLAT)/$(UART_IMAGE)
diff --git a/plat/marvell/armada/a3k/common/a3700_ea.c b/plat/marvell/armada/a3k/common/a3700_ea.c
new file mode 100644
index 0000000..5696b5c
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/a3700_ea.c
@@ -0,0 +1,78 @@
+/*
+ * Copyright (C) 2019 Repk repk@triplefau.lt
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <inttypes.h>
+#include <stdint.h>
+
+#include <common/bl_common.h>
+#include <common/debug.h>
+#include <arch_helpers.h>
+#include <plat/common/platform.h>
+#include <bl31/ea_handle.h>
+
+#define A53_SERR_INT_AXI_SLVERR_ON_EXTERNAL_ACCESS 0xbf000002
+
+/*
+ * This source file with custom plat_ea_handler function is compiled only when
+ * building TF-A with compile option HANDLE_EA_EL3_FIRST_NS=1
+ */
+void plat_ea_handler(unsigned int ea_reason, uint64_t syndrome, void *cookie,
+		void *handle, uint64_t flags)
+{
+	unsigned int level = (unsigned int)GET_EL(read_spsr_el3());
+
+	/*
+	 * Asynchronous External Abort with syndrome 0xbf000002 on Cortex A53
+	 * core means SError interrupt caused by AXI SLVERR on external access.
+	 *
+	 * In most cases this indicates a bug in U-Boot or Linux kernel driver
+	 * pci-aardvark.c which implements access to A3700 PCIe config space.
+	 * Driver does not wait for PCIe PIO transfer completion and try to
+	 * start a new PCIe PIO transfer while previous has not finished yet.
+	 * A3700 PCIe controller in this case sends SLVERR via AXI which results
+	 * in a fatal Asynchronous SError interrupt on Cortex A53 CPU.
+	 *
+	 * Following patches fix that bug in U-Boot and Linux kernel drivers:
+	 * https://source.denx.de/u-boot/u-boot/-/commit/eccbd4ad8e4e182638eafbfb87ac139c04f24a01
+	 * https://git.kernel.org/stable/c/f18139966d072dab8e4398c95ce955a9742e04f7
+	 *
+	 * As a hacky workaround for unpatched U-Boot and Linux kernel drivers
+	 * ignore all asynchronous aborts with that syndrome value received on
+	 * CPU from level lower than EL3.
+	 *
+	 * Because these aborts are delivered on CPU asynchronously, they are
+	 * imprecise and we cannot check the real reason of abort and neither
+	 * who and why sent this abort. We expect that on A3700 it is always
+	 * PCIe controller.
+	 *
+	 * Hence ignoring all aborts with this syndrome value is just a giant
+	 * hack that we need only because of bugs in old U-Boot and Linux kernel
+	 * versions and because it was decided that TF-A would implement this
+	 * hack for U-Boot and Linux kernel it in this way. New patched U-Boot
+	 * and kernel versions do not need it anymore.
+	 *
+	 * Links to discussion about this workaround:
+	 * https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/
+	 * https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/
+	 * https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
+	 */
+	if (level < MODE_EL3 && ea_reason == ERROR_EA_ASYNC &&
+	    syndrome == A53_SERR_INT_AXI_SLVERR_ON_EXTERNAL_ACCESS) {
+		ERROR_NL();
+		ERROR("Ignoring Asynchronous External Abort with"
+		     " syndrome 0x%" PRIx64 " received on 0x%lx from %s\n",
+		     syndrome, read_mpidr_el1(), get_el_str(level));
+		ERROR("SError interrupt: AXI SLVERR on external access\n");
+		ERROR("This indicates a bug in pci-aardvark.c driver\n");
+		ERROR("Please update U-Boot/Linux to the latest version\n");
+		ERROR_NL();
+		console_flush();
+		return;
+	}
+
+	plat_default_ea_handler(ea_reason, syndrome, cookie, handle, flags);
+}
diff --git a/plat/marvell/armada/a3k/common/a3700_sip_svc.c b/plat/marvell/armada/a3k/common/a3700_sip_svc.c
new file mode 100644
index 0000000..e8ac5fc
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/a3700_sip_svc.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#include <common/runtime_svc.h>
+#include <lib/smccc.h>
+
+#include <marvell_plat_priv.h>
+#include <plat_marvell.h>
+
+#include "comphy/phy-comphy-3700.h"
+
+/* Comphy related FID's */
+#define MV_SIP_COMPHY_POWER_ON	0x82000001
+#define MV_SIP_COMPHY_POWER_OFF	0x82000002
+#define MV_SIP_COMPHY_PLL_LOCK	0x82000003
+
+/* Miscellaneous FID's' */
+#define MV_SIP_DRAM_SIZE	0x82000010
+
+/* This macro is used to identify COMPHY related calls from SMC function ID */
+#define is_comphy_fid(fid)	\
+	((fid) >= MV_SIP_COMPHY_POWER_ON && (fid) <= MV_SIP_COMPHY_PLL_LOCK)
+
+uintptr_t mrvl_sip_smc_handler(uint32_t smc_fid,
+			       u_register_t x1,
+			       u_register_t x2,
+			       u_register_t x3,
+			       u_register_t x4,
+			       void *cookie,
+			       void *handle,
+			       u_register_t flags)
+{
+	u_register_t ret;
+
+	VERBOSE("%s: got SMC (0x%x) x1 0x%lx, x2 0x%lx\n",
+		__func__, smc_fid, x1, x2);
+	if (is_comphy_fid(smc_fid)) {
+		if (x1 >= MAX_LANE_NR) {
+			ERROR("%s: Wrong smc (0x%x) lane nr: %lx\n",
+			      __func__, smc_fid, x2);
+			SMC_RET1(handle, SMC_UNK);
+		}
+	}
+
+	switch (smc_fid) {
+	/* Comphy related FID's */
+	case MV_SIP_COMPHY_POWER_ON:
+		/* x1: comphy_index, x2: comphy_mode */
+		ret = mvebu_3700_comphy_power_on(x1, x2);
+		SMC_RET1(handle, ret);
+	case MV_SIP_COMPHY_POWER_OFF:
+		/* x1: comphy_index, x2: comphy_mode */
+		ret = mvebu_3700_comphy_power_off(x1, x2);
+		SMC_RET1(handle, ret);
+	case MV_SIP_COMPHY_PLL_LOCK:
+		/* x1: comphy_index, x2: comphy_mode */
+		ret = mvebu_3700_comphy_is_pll_locked(x1, x2);
+		SMC_RET1(handle, ret);
+	/* Miscellaneous FID's' */
+	case MV_SIP_DRAM_SIZE:
+		/* x1:  ap_base_addr */
+		ret = mvebu_get_dram_size(MVEBU_REGS_BASE);
+		SMC_RET1(handle, ret);
+
+	default:
+		ERROR("%s: unhandled SMC (0x%x)\n", __func__, smc_fid);
+		SMC_RET1(handle, SMC_UNK);
+	}
+}
+
+/* Define a runtime service descriptor for fast SMC calls */
+DECLARE_RT_SVC(
+	marvell_sip_svc,
+	OEN_SIP_START,
+	OEN_SIP_END,
+	SMC_TYPE_FAST,
+	NULL,
+	mrvl_sip_smc_handler
+);
diff --git a/plat/marvell/armada/a3k/common/aarch64/a3700_clock.S b/plat/marvell/armada/a3k/common/aarch64/a3700_clock.S
new file mode 100644
index 0000000..f79516f
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/aarch64/a3700_clock.S
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <asm_macros.S>
+#include <platform_def.h>
+
+/*
+ * Below address in used only for reading, therefore no problem with concurrent
+ * Linux access.
+ */
+#define MVEBU_TEST_PIN_LATCH_N (MVEBU_NB_GPIO_REG_BASE + 0x8)
+ #define MVEBU_XTAL_MODE_MASK		BIT(9)
+
+	/* -----------------------------------------------------
+	 * uint32_t get_ref_clk (void);
+	 *
+	 * returns reference clock in MHz (25 or 40)
+	 * -----------------------------------------------------
+	 */
+.globl	get_ref_clk
+func get_ref_clk
+	mov_imm	x0, MVEBU_TEST_PIN_LATCH_N
+	ldr	w0, [x0]
+	tst	w0, #MVEBU_XTAL_MODE_MASK
+	bne	40
+	mov	w0, #25
+	ret
+40:
+	mov	w0, #40
+	ret
+endfunc get_ref_clk
diff --git a/plat/marvell/armada/a3k/common/aarch64/a3700_common.c b/plat/marvell/armada/a3k/common/aarch64/a3700_common.c
new file mode 100644
index 0000000..6351285
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/aarch64/a3700_common.c
@@ -0,0 +1,53 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+#include <plat_marvell.h>
+
+/* MMU entry for internal (register) space access */
+#define MAP_DEVICE0	MAP_REGION_FLAT(DEVICE0_BASE,			\
+					DEVICE0_SIZE,			\
+					MT_DEVICE | MT_RW | MT_SECURE)
+
+/*
+ * Table of regions for various BL stages to map using the MMU.
+ */
+#if IMAGE_BL1
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SHARED_RAM,
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+#if IMAGE_BL2
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SHARED_RAM,
+	MAP_DEVICE0,
+	MARVELL_MAP_DRAM,
+	{0}
+};
+#endif
+#if IMAGE_BL2U
+const mmap_region_t plat_marvell_mmap[] = {
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+#if IMAGE_BL31
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SHARED_RAM,
+	MAP_DEVICE0,
+	MARVELL_MAP_DRAM,
+	{0}
+};
+#endif
+#if IMAGE_BL32
+const mmap_region_t plat_marvell_mmap[] = {
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+
+MARVELL_CASSERT_MMAP;
diff --git a/plat/marvell/armada/a3k/common/aarch64/plat_helpers.S b/plat/marvell/armada/a3k/common/aarch64/plat_helpers.S
new file mode 100644
index 0000000..90d76f0
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/aarch64/plat_helpers.S
@@ -0,0 +1,68 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <asm_macros.S>
+#include <platform_def.h>
+
+	.globl	plat_secondary_cold_boot_setup
+	.globl	plat_get_my_entrypoint
+	.globl	plat_is_my_cpu_primary
+
+	/* -----------------------------------------------------
+	 * void plat_secondary_cold_boot_setup (void);
+	 *
+	 * This function performs any platform specific actions
+	 * needed for a secondary cpu after a cold reset. Right
+	 * now this is a stub function.
+	 * -----------------------------------------------------
+	 */
+func plat_secondary_cold_boot_setup
+	mov	x0, #0
+	ret
+endfunc plat_secondary_cold_boot_setup
+
+	/* ---------------------------------------------------------------------
+	 * unsigned long plat_get_my_entrypoint (void);
+	 *
+	 * Main job of this routine is to distinguish between cold and warm boot
+	 * For a cold boot, return 0.
+	 * For a warm boot, read the mailbox and return the address it contains.
+	 * A magic number is placed before entrypoint to avoid mistake caused by
+	 * uninitialized mailbox data area.
+	 * ---------------------------------------------------------------------
+	 */
+func plat_get_my_entrypoint
+	/* Read first word and compare it with magic num */
+	mov_imm x0, PLAT_MARVELL_MAILBOX_BASE
+	ldr	x1, [x0]
+	mov_imm x2, PLAT_MARVELL_MAILBOX_MAGIC_NUM
+	cmp	x1, x2
+	/* If compare failed, return 0, i.e. cold boot */
+	beq	entrypoint
+	mov	x0, #0
+	ret
+entrypoint:
+	/* Second word contains the jump address */
+	add	x0, x0, #8
+	ldr	x0, [x0]
+	ret
+endfunc plat_get_my_entrypoint
+
+	/* -----------------------------------------------------
+	 * unsigned int plat_is_my_cpu_primary (void);
+	 *
+	 * Find out whether the current cpu is the primary
+	 * cpu.
+	 * -----------------------------------------------------
+	 */
+func plat_is_my_cpu_primary
+	mrs	x0, mpidr_el1
+	and	x0, x0, #(MPIDR_CLUSTER_MASK | MPIDR_CPU_MASK)
+	cmp	x0, #MVEBU_PRIMARY_CPU
+	cset	w0, eq
+	ret
+endfunc plat_is_my_cpu_primary
diff --git a/plat/marvell/armada/a3k/common/cm3_system_reset.c b/plat/marvell/armada/a3k/common/cm3_system_reset.c
new file mode 100644
index 0000000..f105d59
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/cm3_system_reset.c
@@ -0,0 +1,62 @@
+/*
+ * Copyright (C) 2020 Marek Behun, CZ.NIC
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <stdbool.h>
+
+#include <common/debug.h>
+#include <drivers/delay_timer.h>
+#include <lib/mmio.h>
+
+#include <mvebu_def.h>
+
+/* Cortex-M3 Secure Processor Mailbox Registers */
+#define MVEBU_RWTM_PARAM0_REG			(MVEBU_RWTM_REG_BASE)
+#define MVEBU_RWTM_CMD_REG			(MVEBU_RWTM_REG_BASE + 0x40)
+#define MVEBU_RWTM_HOST_INT_RESET_REG		(MVEBU_RWTM_REG_BASE + 0xC8)
+#define MVEBU_RWTM_HOST_INT_MASK_REG		(MVEBU_RWTM_REG_BASE + 0xCC)
+#define MVEBU_RWTM_HOST_INT_SP_COMPLETE		BIT(0)
+
+#define MVEBU_RWTM_REBOOT_CMD		0x0009
+#define MVEBU_RWTM_REBOOT_MAGIC		0xDEADBEEF
+
+static inline bool rwtm_completed(void)
+{
+	return (mmio_read_32(MVEBU_RWTM_HOST_INT_RESET_REG) &
+		MVEBU_RWTM_HOST_INT_SP_COMPLETE) != 0;
+}
+
+static bool rwtm_wait(int ms)
+{
+	while (ms && !rwtm_completed()) {
+		mdelay(1);
+		--ms;
+	}
+
+	return rwtm_completed();
+}
+
+void cm3_system_reset(void)
+{
+	int tries = 5;
+
+	for (; tries > 0; --tries) {
+		mmio_clrbits_32(MVEBU_RWTM_HOST_INT_RESET_REG,
+				MVEBU_RWTM_HOST_INT_SP_COMPLETE);
+
+		mmio_write_32(MVEBU_RWTM_PARAM0_REG, MVEBU_RWTM_REBOOT_MAGIC);
+		mmio_write_32(MVEBU_RWTM_CMD_REG, MVEBU_RWTM_REBOOT_CMD);
+
+		if (rwtm_wait(10)) {
+			break;
+		}
+
+		mdelay(100);
+	}
+
+	/* If we reach here, the command is not implemented. */
+	WARN("System reset command not implemented in WTMI firmware!\n");
+}
diff --git a/plat/marvell/armada/a3k/common/dram_win.c b/plat/marvell/armada/a3k/common/dram_win.c
new file mode 100644
index 0000000..9d7b3a9
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/dram_win.c
@@ -0,0 +1,282 @@
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <string.h>
+
+#include <lib/mmio.h>
+
+#include <dram_win.h>
+#include <marvell_plat_priv.h>
+#include <mvebu.h>
+#include <plat_marvell.h>
+
+/* Armada 3700 has 5 configurable windows */
+#define MV_CPU_WIN_NUM		5
+
+#define CPU_WIN_DISABLED	0
+#define CPU_WIN_ENABLED		1
+
+/*
+ * There are 2 different cpu decode window configuration cases:
+ * - DRAM size is not over 2GB;
+ * - DRAM size is 4GB.
+ */
+enum cpu_win_config_num {
+	CPU_WIN_CONFIG_DRAM_NOT_OVER_2GB = 0,
+	CPU_WIN_CONFIG_DRAM_4GB,
+	CPU_WIN_CONFIG_MAX
+};
+
+enum cpu_win_target {
+	CPU_WIN_TARGET_DRAM = 0,
+	CPU_WIN_TARGET_INTERNAL_REG,
+	CPU_WIN_TARGET_PCIE,
+	CPU_WIN_TARGET_PCIE_OVER_MCI,
+	CPU_WIN_TARGET_BOOT_ROM,
+	CPU_WIN_TARGET_MCI_EXTERNAL,
+	CPU_WIN_TARGET_RWTM_RAM = 7,
+	CPU_WIN_TARGET_CCI400_REG
+};
+
+struct cpu_win_configuration {
+	uint32_t		enabled;
+	enum cpu_win_target	target;
+	uint64_t		base_addr;
+	uint64_t		size;
+	uint64_t		remap_addr;
+};
+
+struct cpu_win_configuration mv_cpu_wins[CPU_WIN_CONFIG_MAX][MV_CPU_WIN_NUM] = {
+	/*
+	 * When total dram size is not over 2GB:
+	 * DDR window 0 is configured in tim header, its size may be not 512MB,
+	 * but the actual dram size, no need to configure it again;
+	 * other cpu windows are kept as default.
+	 */
+	{
+		/* enabled
+		 *	target
+		 *		base
+		 *			size
+		 *				remap
+		 */
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_DRAM,
+				0x0,
+					0x08000000,
+						0x0},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_MCI_EXTERNAL,
+				0xe0000000,
+					0x08000000,
+						0xe0000000},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_PCIE,
+				0xe8000000,
+					0x08000000,
+						0xe8000000},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_RWTM_RAM,
+				0xf0000000,
+					0x00020000,
+						0x1fff0000},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_PCIE_OVER_MCI,
+				0x80000000,
+					0x10000000,
+						0x80000000},
+	},
+
+	/*
+	 * If total DRAM size is more than 2GB, now there is only one case:
+	 * 4GB of DRAM; to better utilize address space (for maximization of
+	 * DRAM usage), we will use the configuration of CPU windows below:
+	 *  - Internal Regs and Boot ROM windows are kept as default;
+	 *  - CCI-400 is moved from its default address to another address
+	 *    (this is actually done even if DRAM size is not more than 2 GB,
+	 *     because the firmware is compiled with that address as a
+	 *     constant);
+	 *  - PCIe window is moved to another address;
+	 *  - Use 4 CPU decode windows for DRAM, which cover 3.75GB DRAM;
+	 *    DDR window 0 is configured in tim header with 2G B size, no need
+	 *    to configure it again here;
+	 *
+	 *	0xFFFFFFFF ---> +-----------------------+
+	 *			|	 Boot ROM	| 1 MB
+	 *			| AP Boot ROM - 16 KB:  |
+	 *			| 0xFFFF0000-0xFFFF4000 |
+	 *	0xFFF00000 ---> +-----------------------+
+	 *			:			:
+	 *	0xFE010000 ---> +-----------------------+
+	 *			|	 CCI Regs	| 64 KB
+	 *	0xFE000000 ---> +-----------------------+
+	 *			:			:
+	 *	0xFA000000 ---> +-----------------------+
+	 *			|	 PCIE		| 128 MB
+	 *	0xF2000000 ---> +-----------------------+
+	 *			|	 DDR window 3	| 512 MB
+	 *	0xD2000000 ---> +-----------------------+
+	 *			|	 Internal Regs	| 32 MB
+	 *	0xD0000000 ---> |-----------------------|
+	 *			|	 DDR window 2	| 256 MB
+	 *	0xC0000000 ---> |-----------------------|
+	 *			|			|
+	 *			|	 DDR window 1	| 1 GB
+	 *			|			|
+	 *	0x80000000 ---> |-----------------------|
+	 *			|			|
+	 *			|			|
+	 *			|	 DDR window 0	| 2 GB
+	 *			|			|
+	 *			|			|
+	 *	0x00000000 ---> +-----------------------+
+	 */
+	{
+		/* win_id
+		 *	target
+		 *		base
+		 *			size
+		 *				remap
+		 */
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_DRAM,
+				0x0,
+					0x80000000,
+						0x0},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_DRAM,
+				0x80000000,
+					0x40000000,
+						0x80000000},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_DRAM,
+				0xc0000000,
+					0x10000000,
+						0xc0000000},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_DRAM,
+				0xd2000000,
+					0x20000000,
+						0xd2000000},
+		{CPU_WIN_ENABLED,
+			CPU_WIN_TARGET_PCIE,
+				0xf2000000,
+					0x08000000,
+						0xf2000000},
+	},
+};
+
+/*
+ * dram_win_map_build
+ *
+ * This function builds cpu dram windows mapping
+ * which includes base address and window size by
+ * reading cpu dram decode windows registers.
+ *
+ * @input: N/A
+ *
+ * @output:
+ *     - win_map: cpu dram windows mapping
+ *
+ * @return:  N/A
+ */
+void dram_win_map_build(struct dram_win_map *win_map)
+{
+	int32_t win_id;
+	struct dram_win *win;
+	uint32_t base_reg, ctrl_reg, size_reg, enabled, target;
+
+	memset(win_map, 0, sizeof(struct dram_win_map));
+	for (win_id = 0; win_id < DRAM_WIN_MAP_NUM_MAX; win_id++) {
+		ctrl_reg = mmio_read_32(CPU_DEC_WIN_CTRL_REG(win_id));
+		target = (ctrl_reg & CPU_DEC_CR_WIN_TARGET_MASK) >>
+			  CPU_DEC_CR_WIN_TARGET_OFFS;
+		enabled = ctrl_reg & CPU_DEC_CR_WIN_ENABLE;
+		/* Ignore invalid and non-dram windows*/
+		if ((enabled == 0) || (target != DRAM_CPU_DEC_TARGET_NUM))
+			continue;
+
+		win = win_map->dram_windows + win_map->dram_win_num;
+		base_reg = mmio_read_32(CPU_DEC_WIN_BASE_REG(win_id));
+		size_reg = mmio_read_32(CPU_DEC_WIN_SIZE_REG(win_id));
+		/* Base reg [15:0] corresponds to transaction address [39:16] */
+		win->base_addr = (base_reg & CPU_DEC_BR_BASE_MASK) >>
+				  CPU_DEC_BR_BASE_OFFS;
+		win->base_addr *= CPU_DEC_CR_WIN_SIZE_ALIGNMENT;
+		/*
+		 * Size reg [15:0] is programmed from LSB to MSB as a sequence
+		 * of 1s followed by a sequence of 0s and the number of 1s
+		 * specifies the size of the window in 64 KB granularity,
+		 * for example, a value of 00FFh specifies 256 x 64 KB = 16 MB
+		 */
+		win->win_size = (size_reg & CPU_DEC_CR_WIN_SIZE_MASK) >>
+				 CPU_DEC_CR_WIN_SIZE_OFFS;
+		win->win_size = (win->win_size + 1) *
+				 CPU_DEC_CR_WIN_SIZE_ALIGNMENT;
+
+		win_map->dram_win_num++;
+	}
+}
+
+static void cpu_win_set(uint32_t win_id, struct cpu_win_configuration *win_cfg)
+{
+	uint32_t base_reg, ctrl_reg, size_reg, remap_reg;
+
+	/* Disable window */
+	ctrl_reg = mmio_read_32(CPU_DEC_WIN_CTRL_REG(win_id));
+	ctrl_reg &= ~CPU_DEC_CR_WIN_ENABLE;
+	mmio_write_32(CPU_DEC_WIN_CTRL_REG(win_id), ctrl_reg);
+
+	/* For an disabled window, only disable it. */
+	if (!win_cfg->enabled)
+		return;
+
+	/* Set Base Register */
+	base_reg = (uint32_t)(win_cfg->base_addr /
+		   CPU_DEC_CR_WIN_SIZE_ALIGNMENT);
+	base_reg <<= CPU_DEC_BR_BASE_OFFS;
+	base_reg &= CPU_DEC_BR_BASE_MASK;
+	mmio_write_32(CPU_DEC_WIN_BASE_REG(win_id), base_reg);
+
+	/* Set Remap Register with the same value
+	 * as the <Base> field in Base Register
+	 */
+	remap_reg = (uint32_t)(win_cfg->remap_addr /
+		    CPU_DEC_CR_WIN_SIZE_ALIGNMENT);
+	remap_reg <<= CPU_DEC_RLR_REMAP_LOW_OFFS;
+	remap_reg &= CPU_DEC_RLR_REMAP_LOW_MASK;
+	mmio_write_32(CPU_DEC_REMAP_LOW_REG(win_id), remap_reg);
+
+	/* Set Size Register */
+	size_reg = (win_cfg->size / CPU_DEC_CR_WIN_SIZE_ALIGNMENT) - 1;
+	size_reg <<= CPU_DEC_CR_WIN_SIZE_OFFS;
+	size_reg &= CPU_DEC_CR_WIN_SIZE_MASK;
+	mmio_write_32(CPU_DEC_WIN_SIZE_REG(win_id), size_reg);
+
+	/* Set Control Register - set target id and enable window */
+	ctrl_reg &= ~CPU_DEC_CR_WIN_TARGET_MASK;
+	ctrl_reg |= (win_cfg->target << CPU_DEC_CR_WIN_TARGET_OFFS);
+	ctrl_reg |= CPU_DEC_CR_WIN_ENABLE;
+	mmio_write_32(CPU_DEC_WIN_CTRL_REG(win_id), ctrl_reg);
+}
+
+void cpu_wins_init(void)
+{
+	uint32_t cfg_idx, win_id;
+
+	if (mvebu_get_dram_size(MVEBU_REGS_BASE) <= _2GB_)
+		cfg_idx = CPU_WIN_CONFIG_DRAM_NOT_OVER_2GB;
+	else
+		cfg_idx = CPU_WIN_CONFIG_DRAM_4GB;
+
+	/* Window 0 is configured always for DRAM in tim header
+	 * already, no need to configure it again here
+	 */
+	for (win_id = 1; win_id < MV_CPU_WIN_NUM; win_id++)
+		cpu_win_set(win_id, &mv_cpu_wins[cfg_idx][win_id]);
+}
+
diff --git a/plat/marvell/armada/a3k/common/include/a3700_plat_def.h b/plat/marvell/armada/a3k/common/include/a3700_plat_def.h
new file mode 100644
index 0000000..4d45e15
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/a3700_plat_def.h
@@ -0,0 +1,169 @@
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef A3700_PLAT_DEF_H
+#define A3700_PLAT_DEF_H
+
+#include <marvell_def.h>
+
+
+#define MVEBU_MAX_CPUS_PER_CLUSTER	2
+
+#define MVEBU_PRIMARY_CPU		0x0
+
+/*
+ * The counter on A3700 is always fed from reference 25M clock (XTAL).
+ * However minimal CPU counter prescaler is 2, so the counter
+ * frequency will be divided by 2, the number is 12.5M
+ */
+#define COUNTER_FREQUENCY		12500000
+
+#define MVEBU_REGS_BASE			0xD0000000
+
+/*****************************************************************************
+ * MVEBU memory map related constants
+ *****************************************************************************
+ */
+/* Aggregate of all devices in the first GB */
+#define DEVICE0_BASE			MVEBU_REGS_BASE
+#define DEVICE0_SIZE			0x10000000
+
+/*****************************************************************************
+ * GIC-500 & interrupt handling related constants
+ *****************************************************************************
+ */
+/* Base MVEBU compatible GIC memory map */
+#define MVEBU_GICD_BASE			0x1D00000
+#define MVEBU_GICR_BASE			0x1D40000
+#define MVEBU_GICC_BASE			0x1D80000
+
+/*
+ * CCI-400 base address
+ * This address is absolute, not relative to MVEBU_REGS_BASE.
+ * This is not the default CCI base address (that would be 0xD8000000).
+ * Rather we remap CCI to this address to better utilize the address space.
+ * (The remapping is done in plat/marvell/armada/a3k/common/plat_cci.c)
+ */
+#define MVEBU_CCI_BASE			0xFE000000
+
+/*****************************************************************************
+ * North and south bridge reset registers
+ *****************************************************************************
+ */
+#define MVEBU_NB_RESET_REG		(MVEBU_REGS_BASE + 0x12400)
+#define   MVEBU_NB_RESET_I2C1_N		(1 << 0)
+#define   MVEBU_NB_RESET_1WIRE_N	(1 << 1)
+#define   MVEBU_NB_RESET_SPI_N		(1 << 2)
+#define   MVEBU_NB_RESET_UART_N		(1 << 3)
+#define   MVEBU_NB_RESET_XTL_N		(1 << 4)
+#define   MVEBU_NB_RESET_I2C2_N		(1 << 5)
+#define   MVEBU_NB_RESET_UART2_N	(1 << 6)
+#define   MVEBU_NB_RESET_AVS_N		(1 << 7)
+#define   MVEBU_NB_RESET_DDR_N		(1 << 10)
+#define   MVEBU_NB_RESET_SETM_N		(1 << 11)
+#define   MVEBU_NB_RESET_DMA_N		(1 << 12)
+#define   MVEBU_NB_RESET_TSECM_N	(1 << 13)
+#define   MVEBU_NB_RESET_SDIO_N		(1 << 14)
+#define   MVEBU_NB_RESET_SATA_N		(1 << 15)
+#define   MVEBU_NB_RESET_PWRMGT_N	(1 << 16)
+#define   MVEBU_NB_RESET_OTP_N		(1 << 17)
+#define   MVEBU_NB_RESET_EIP_N		(1 << 18)
+#define MVEBU_SB_RESET_REG		(MVEBU_REGS_BASE + 0x18600)
+#define   MVEBU_SB_RESET_MCIPHY		(1 << 1)
+#define   MVEBU_SB_RESET_SDIO_N		(1 << 2)
+#define   MVEBU_SB_RESET_PCIE_N		(1 << 3)
+#define   MVEBU_SB_RESET_GBE1_N		(1 << 4)
+#define   MVEBU_SB_RESET_GBE0_N		(1 << 5)
+#define   MVEBU_SB_RESET_USB2PHY	(1 << 6)
+#define   MVEBU_SB_RESET_USB2HPHY	(1 << 7)
+#define   MVEBU_SB_RESET_MCI_N		(1 << 8)
+#define   MVEBU_SB_RESET_PWRMGT_N	(1 << 9)
+#define   MVEBU_SB_RESET_EBM_N		(1 << 10)
+#define   MVEBU_SB_RESET_OTP_N		(1 << 11)
+
+/*****************************************************************************
+ * North and south bridge register base
+ *****************************************************************************
+ */
+#define MVEBU_NB_REGS_BASE			(MVEBU_REGS_BASE + 0x13000)
+#define MVEBU_SB_REGS_BASE			(MVEBU_REGS_BASE + 0x18000)
+
+/*****************************************************************************
+ * GPIO registers related constants
+ *****************************************************************************
+ */
+/* North and south bridge GPIO register base address */
+#define MVEBU_NB_GPIO_REG_BASE			(MVEBU_NB_REGS_BASE + 0x800)
+#define MVEBU_NB_GPIO_IRQ_REG_BASE		(MVEBU_NB_REGS_BASE + 0xC00)
+#define MVEBU_SB_GPIO_REG_BASE			(MVEBU_SB_REGS_BASE + 0x800)
+#define MVEBU_SB_GPIO_IRQ_REG_BASE		(MVEBU_SB_REGS_BASE + 0xC00)
+#define MVEBU_NB_SB_IRQ_REG_BASE		(MVEBU_REGS_BASE + 0x8A00)
+
+/* North Bridge GPIO selection register */
+#define MVEBU_NB_GPIO_SEL_REG			(MVEBU_NB_GPIO_REG_BASE + 0x30)
+#define MVEBU_NB_GPIO_OUTPUT_EN_HIGH_REG	(MVEBU_NB_GPIO_REG_BASE + 0x04)
+/* I2C1 GPIO Enable bit offset */
+#define MVEBU_GPIO_TW1_GPIO_EN_OFF		(10)
+/* SPI pins mode bit offset */
+#define MVEBU_GPIO_NB_SPI_PIN_MODE_OFF		(28)
+
+/*****************************************************************************
+ * DRAM registers related constants
+ *****************************************************************************
+ */
+#define MVEBU_DRAM_REG_BASE			(MVEBU_REGS_BASE)
+
+/*****************************************************************************
+ * SB wake-up registers related constants
+ *****************************************************************************
+ */
+#define MVEBU_SB_WAKEUP_REG_BASE		(MVEBU_REGS_BASE + 0x19000)
+
+/*****************************************************************************
+ * PMSU registers related constants
+ *****************************************************************************
+ */
+#define MVEBU_PMSU_REG_BASE			(MVEBU_REGS_BASE + 0x14000)
+
+/*****************************************************************************
+ * North Bridge Step-Down Registers
+ *****************************************************************************
+ */
+#define MVEBU_NB_STEP_DOWN_REG_BASE		(MVEBU_REGS_BASE + 0x12800)
+
+/*****************************************************************************
+ * DRAM CS memory map register base
+ *****************************************************************************
+ */
+#define MVEBU_CS_MMAP_REG_BASE			(MVEBU_REGS_BASE + 0x200)
+
+/*****************************************************************************
+ * CPU decoder window registers related constants
+ *****************************************************************************
+ */
+#define MVEBU_CPU_DEC_WIN_REG_BASE		(MVEBU_REGS_BASE + 0xCF00)
+
+/*****************************************************************************
+ * AVS registers related constants
+ *****************************************************************************
+ */
+#define MVEBU_AVS_REG_BASE			(MVEBU_REGS_BASE + 0x11500)
+
+
+/*****************************************************************************
+ * AVS registers related constants
+ *****************************************************************************
+ */
+#define MVEBU_COMPHY_REG_BASE			(MVEBU_REGS_BASE + 0x18300)
+
+/*****************************************************************************
+ * Cortex-M3 Secure Processor Mailbox constants
+ *****************************************************************************
+ */
+#define MVEBU_RWTM_REG_BASE			(MVEBU_REGS_BASE + 0xB0000)
+
+#endif /* A3700_PLAT_DEF_H */
diff --git a/plat/marvell/armada/a3k/common/include/a3700_pm.h b/plat/marvell/armada/a3k/common/include/a3700_pm.h
new file mode 100644
index 0000000..44dbb9f
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/a3700_pm.h
@@ -0,0 +1,53 @@
+/*
+ * Copyright (C) 2016-2020 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef A3700_PM_H
+#define A3700_PM_H
+
+#include <stdint.h>
+
+/* supported wake up sources */
+enum pm_wake_up_src_type {
+	WAKE_UP_SRC_GPIO,
+	/* FOLLOWING SRC NOT SUPPORTED YET */
+	WAKE_UP_SRC_TIMER,
+	WAKE_UP_SRC_UART0,
+	WAKE_UP_SRC_UART1,
+	WAKE_UP_SRC_MAX,
+};
+
+struct pm_gpio_data {
+	/*
+	 * bank 0: North bridge GPIO
+	 * bank 1: South bridge GPIO
+	 */
+	uint32_t bank_num;
+	uint32_t gpio_num;
+};
+
+union pm_wake_up_src_data {
+	struct pm_gpio_data gpio_data;
+	/* delay in seconds */
+	uint32_t timer_delay;
+};
+
+struct pm_wake_up_src {
+	enum pm_wake_up_src_type wake_up_src_type;
+
+	union pm_wake_up_src_data wake_up_data;
+};
+
+struct pm_wake_up_src_config {
+	uint32_t	wake_up_src_num;
+	struct pm_wake_up_src wake_up_src[WAKE_UP_SRC_MAX];
+};
+
+struct pm_wake_up_src_config *mv_wake_up_src_config_get(void);
+
+void cm3_system_reset(void);
+
+#endif /* A3700_PM_H */
diff --git a/plat/marvell/armada/a3k/common/include/ddr_info.h b/plat/marvell/armada/a3k/common/include/ddr_info.h
new file mode 100644
index 0000000..254f78c
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/ddr_info.h
@@ -0,0 +1,14 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef DDR_INFO_H
+#define DDR_INFO_H
+
+#define DRAM_MAX_IFACE			1
+#define DRAM_CH0_MMAP_LOW_OFFSET	0x200
+
+#endif /* DDR_INFO_H */
diff --git a/plat/marvell/armada/a3k/common/include/dram_win.h b/plat/marvell/armada/a3k/common/include/dram_win.h
new file mode 100644
index 0000000..26a0137
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/dram_win.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef DRAM_WIN_H
+#define DRAM_WIN_H
+
+#include <common/bl_common.h>
+
+#include <io_addr_dec.h>
+
+void dram_win_map_build(struct dram_win_map *win_map);
+void cpu_wins_init(void);
+
+#endif /* DRAM_WIN_H */
diff --git a/plat/marvell/armada/a3k/common/include/io_addr_dec.h b/plat/marvell/armada/a3k/common/include/io_addr_dec.h
new file mode 100644
index 0000000..42ef30b
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/io_addr_dec.h
@@ -0,0 +1,66 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef IO_ADDR_DEC_H
+#define IO_ADDR_DEC_H
+
+#include <stdint.h>
+
+/* There are 5 configurable cpu decoder windows. */
+#define DRAM_WIN_MAP_NUM_MAX	5
+/* Target number for dram in cpu decoder windows. */
+#define DRAM_CPU_DEC_TARGET_NUM	0
+
+/*
+ * Not all configurable decode windows could be used for dram, some units have
+ * to reserve one decode window for other unit they have to communicate with;
+ * for example, DMA engineer has 3 configurable windows, but only two could be
+ * for dram while the last one has to be for pcie, so for DMA, its max_dram_win
+ * is 2.
+ */
+struct dec_win_config {
+	uint32_t dec_reg_base; /* IO address decoder register base address */
+	uint32_t win_attr;	/* IO address decoder windows attributes */
+	/* How many configurable dram decoder windows that this unit has; */
+	uint32_t max_dram_win;
+	/* The decoder windows number including remapping that this unit has */
+	uint32_t max_remap;
+	/* The offset between continuous decode windows
+	 * within the same unit, typically 0x10
+	 */
+	uint32_t win_offset;
+};
+
+struct dram_win {
+	uintptr_t base_addr;
+	uintptr_t win_size;
+};
+
+struct  dram_win_map {
+	int dram_win_num;
+	struct dram_win dram_windows[DRAM_WIN_MAP_NUM_MAX];
+};
+
+/*
+ * init_io_addr_dec
+ *
+ * This function initializes io address decoder windows by
+ * cpu dram window mapping information
+ *
+ * @input: N/A
+ *     - dram_wins_map: cpu dram windows mapping
+ *     - io_dec_config: io address decoder windows configuration
+ *     - io_unit_num: io address decoder unit number
+ * @output: N/A
+ *
+ * @return:  0 on success and others on failure
+ */
+int init_io_addr_dec(struct dram_win_map *dram_wins_map,
+		     struct dec_win_config *io_dec_config,
+		     uint32_t io_unit_num);
+
+#endif /* IO_ADDR_DEC_H */
diff --git a/plat/marvell/armada/a3k/common/include/plat_macros.S b/plat/marvell/armada/a3k/common/include/plat_macros.S
new file mode 100644
index 0000000..f689b4f
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/plat_macros.S
@@ -0,0 +1,26 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef PLAT_MACROS_S
+#define PLAT_MACROS_S
+
+#include <marvell_macros.S>
+
+/* ---------------------------------------------
+ * The below macro prints out relevant GIC and
+ * CCI registers registers whenever an unhandled
+ * exception is taken in BL31.
+ * ---------------------------------------------
+ */
+.macro plat_crash_print_regs
+	mov_imm	x17, MVEBU_GICC_BASE
+	mov_imm	x16, MVEBU_GICD_BASE
+	marvell_print_gic_regs
+	print_cci_regs
+.endm
+
+#endif /* PLAT_MACROS_S */
diff --git a/plat/marvell/armada/a3k/common/include/platform_def.h b/plat/marvell/armada/a3k/common/include/platform_def.h
new file mode 100644
index 0000000..f19d96b
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/include/platform_def.h
@@ -0,0 +1,228 @@
+/*
+ * Copyright (C) 2016-2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef PLATFORM_DEF_H
+#define PLATFORM_DEF_H
+
+#ifndef __ASSEMBLER__
+#include <stdio.h>
+#endif /* __ASSEMBLER__ */
+
+#include <board_marvell_def.h>
+#include <mvebu_def.h>
+
+/*
+ * Most platform porting definitions provided by included headers
+ */
+
+/*
+ * DRAM Memory layout:
+ *		+-----------------------+
+ *		:			:
+ *		:	Linux		:
+ * 0x04X00000-->+-----------------------+
+ *		|	BL3-3(u-boot)	|>>}>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
+ *		|-----------------------|  }				       |
+ *		|	BL3-[0,1, 2]	|  }---------------------------------> |
+ *		|-----------------------|  }				||     |
+ *		|	BL2		|  }->FIP (loaded by            ||     |
+ *		|-----------------------|  }       BootROM to DRAM)     ||     |
+ *		|	FIP_TOC		|  }                            ||     |
+ * 0x04120000-->|-----------------------|				||     |
+ *		|	BL1 (RO)	|				||     |
+ * 0x04100000-->+-----------------------+				||     |
+ *		:			:				||     |
+ *		: Trusted SRAM section	:				\/     |
+ * 0x04040000-->+-----------------------+  Replaced by BL2  +----------------+ |
+ *		|	BL1 (RW)	|  <<<<<<<<<<<<<<<< | BL3-1 NOBITS   | |
+ * 0x04037000-->|-----------------------|  <<<<<<<<<<<<<<<< |----------------| |
+ *		|			|  <<<<<<<<<<<<<<<< | BL3-1 PROGBITS | |
+ * 0x04023000-->|-----------------------|		    +----------------+ |
+ *		|	BL2		|				       |
+ *		|-----------------------|				       |
+ *		|			|				       |
+ * 0x04001000-->|-----------------------|				       |
+ *		|	Shared		|				       |
+ * 0x04000000-->+-----------------------+				       |
+ *		:			:				       |
+ *		:	Linux		:				       |
+ *		:			:				       |
+ *		|-----------------------|				       |
+ *		|			|	U-Boot(BL3-3) Loaded by BL2    |
+ *		|	U-Boot		|	<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
+ * 0x00000000-->+-----------------------+
+ *
+ * Trusted SRAM section 0x4000000..0x4200000:
+ * ----------------------------------------
+ * SRAM_BASE		= 0x4001000
+ * BL2_BASE		= 0x4006000
+ * BL2_LIMIT		= BL31_BASE
+ * BL31_BASE		= 0x4023000 = (64MB + 256KB - 0x1D000)
+ * BL31_PROGBITS_LIMIT	= BL1_RW_BASE
+ * BL1_RW_BASE		= 0x4037000 = (64MB + 256KB - 0x9000)
+ * BL1_RW_LIMIT		= BL31_LIMIT = 0x4040000
+ *
+ *
+ * PLAT_MARVELL_FIP_BASE	= 0x4120000
+ */
+
+/*
+ * Since BL33 is loaded by BL2 (and validated by BL31) to DRAM offset 0,
+ * it is allowed to load/copy images to 'NULL' pointers
+ */
+#if defined(IMAGE_BL2) || defined(IMAGE_BL31)
+#define PLAT_ALLOW_ZERO_ADDR_COPY
+#endif
+
+#define PLAT_MARVELL_ATF_BASE			0x4000000
+#define PLAT_MARVELL_ATF_LOAD_ADDR		\
+			(PLAT_MARVELL_ATF_BASE + 0x100000)
+
+#define PLAT_MARVELL_FIP_BASE			\
+			(PLAT_MARVELL_ATF_LOAD_ADDR + 0x20000)
+#define PLAT_MARVELL_FIP_MAX_SIZE		0x4000000
+
+#define PLAT_MARVELL_CLUSTER_CORE_COUNT		U(2)
+/* DRAM[2MB..66MB] is used  as Trusted ROM */
+#define PLAT_MARVELL_TRUSTED_ROM_BASE		PLAT_MARVELL_ATF_LOAD_ADDR
+/* 4 MB for FIP image */
+#define PLAT_MARVELL_TRUSTED_ROM_SIZE		0x00400000
+/* Reserve 12M for SCP (Secure PayLoad) Trusted RAM
+ * OP-TEE SHMEM follows this region
+ */
+#define PLAT_MARVELL_TRUSTED_RAM_BASE		0x04400000
+#define PLAT_MARVELL_TRUSTED_RAM_SIZE		0x00C00000	/* 12 MB DRAM */
+
+/*
+ * PLAT_ARM_MAX_BL1_RW_SIZE is calculated using the current BL1 RW debug size
+ * plus a little space for growth.
+ */
+#define PLAT_MARVELL_MAX_BL1_RW_SIZE		0xA000
+
+/*
+ * PLAT_ARM_MAX_BL2_SIZE is calculated using the current BL2 debug size plus a
+ * little space for growth.
+ */
+#define PLAT_MARVELL_MAX_BL2_SIZE		0xF000
+
+/*
+ * PLAT_ARM_MAX_BL31_SIZE is calculated using the current BL31 debug size plus a
+ * little space for growth.
+ */
+#define PLAT_MARVEL_MAX_BL31_SIZE		0x5D000
+
+#define PLAT_MARVELL_CPU_ENTRY_ADDR		BL1_RO_BASE
+
+/* GIC related definitions */
+#define PLAT_MARVELL_GICD_BASE		(MVEBU_REGS_BASE + MVEBU_GICD_BASE)
+#define PLAT_MARVELL_GICR_BASE		(MVEBU_REGS_BASE + MVEBU_GICR_BASE)
+#define PLAT_MARVELL_GICC_BASE		(MVEBU_REGS_BASE + MVEBU_GICC_BASE)
+
+#define PLAT_MARVELL_G0_IRQ_PROPS(grp) \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_0, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_6, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL)
+
+#define PLAT_MARVELL_G1S_IRQ_PROPS(grp) \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_PHY_TIMER, \
+			GIC_HIGHEST_SEC_PRIORITY, grp, GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_1, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_2, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_3, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_4, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_5, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_7, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL)
+
+
+#define PLAT_MARVELL_SHARED_RAM_CACHED		1
+
+/* CCI related constants */
+#define PLAT_MARVELL_CCI_BASE			MVEBU_CCI_BASE
+#define PLAT_MARVELL_CCI_CLUSTER0_SL_IFACE_IX	3
+#define PLAT_MARVELL_CCI_CLUSTER1_SL_IFACE_IX	4
+
+/*
+ * Load address of BL3-3 for this platform port
+ */
+#define PLAT_MARVELL_NS_IMAGE_OFFSET		0x0
+
+/* System Reference Clock*/
+#define PLAT_REF_CLK_IN_HZ			COUNTER_FREQUENCY
+
+/*
+ * PL011 related constants
+ */
+#define PLAT_MARVELL_UART_BASE			(MVEBU_REGS_BASE + 0x12000)
+
+/* Required platform porting definitions */
+#define PLAT_MAX_PWR_LVL			MPIDR_AFFLVL1
+
+/* System timer related constants */
+#define PLAT_MARVELL_NSTIMER_FRAME_ID		1
+
+/* Mailbox base address */
+#define PLAT_MARVELL_MAILBOX_BASE	(MARVELL_SHARED_RAM_BASE + 0x400)
+#define PLAT_MARVELL_MAILBOX_SIZE		0x100
+#define PLAT_MARVELL_MAILBOX_MAGIC_NUM		0x6D72766C	/* mrvl */
+
+/* DRAM CS memory map registers related constants */
+#define MVEBU_CS_MMAP_LOW(cs_num)		\
+			(MVEBU_CS_MMAP_REG_BASE + (cs_num) * 0x8)
+#define MVEBU_CS_MMAP_ENABLE			0x1
+#define MVEBU_CS_MMAP_AREA_LEN_OFFS		16
+#define MVEBU_CS_MMAP_AREA_LEN_MASK		\
+			(0x1f << MVEBU_CS_MMAP_AREA_LEN_OFFS)
+#define MVEBU_CS_MMAP_START_ADDR_LOW_OFFS	23
+#define MVEBU_CS_MMAP_START_ADDR_LOW_MASK	\
+			(0x1ff << MVEBU_CS_MMAP_START_ADDR_LOW_OFFS)
+
+#define MVEBU_CS_MMAP_HIGH(cs_num)		\
+			(MVEBU_CS_MMAP_REG_BASE + 0x4 + (cs_num) * 0x8)
+
+/* DRAM max CS number */
+#define MVEBU_MAX_CS_MMAP_NUM			(2)
+
+/* CPU decoder window related constants */
+#define CPU_DEC_WIN_CTRL_REG(win_num)		\
+			(MVEBU_CPU_DEC_WIN_REG_BASE + (win_num) * 0x10)
+#define CPU_DEC_CR_WIN_ENABLE			0x1
+#define CPU_DEC_CR_WIN_TARGET_OFFS		4
+#define CPU_DEC_CR_WIN_TARGET_MASK		\
+			(0xf << CPU_DEC_CR_WIN_TARGET_OFFS)
+
+#define CPU_DEC_WIN_SIZE_REG(win_num)		\
+			(MVEBU_CPU_DEC_WIN_REG_BASE + 0x4 + (win_num) * 0x10)
+#define CPU_DEC_CR_WIN_SIZE_OFFS		0
+#define CPU_DEC_CR_WIN_SIZE_MASK		\
+			(0xffff << CPU_DEC_CR_WIN_SIZE_OFFS)
+#define CPU_DEC_CR_WIN_SIZE_ALIGNMENT		0x10000
+
+#define CPU_DEC_WIN_BASE_REG(win_num)		\
+			(MVEBU_CPU_DEC_WIN_REG_BASE + 0x8 + (win_num) * 0x10)
+#define CPU_DEC_BR_BASE_OFFS			0
+#define CPU_DEC_BR_BASE_MASK			\
+			(0xffff <<  CPU_DEC_BR_BASE_OFFS)
+
+#define CPU_DEC_REMAP_LOW_REG(win_num)		\
+			(MVEBU_CPU_DEC_WIN_REG_BASE + 0xC + (win_num) * 0x10)
+#define CPU_DEC_RLR_REMAP_LOW_OFFS		0
+#define CPU_DEC_RLR_REMAP_LOW_MASK		\
+			(0xffff <<  CPU_DEC_BR_BASE_OFFS)
+
+#define CPU_DEC_CCI_BASE_REG		(MVEBU_CPU_DEC_WIN_REG_BASE + 0xe0)
+
+/* Securities */
+#define IRQ_SEC_OS_TICK_INT	MARVELL_IRQ_SEC_PHY_TIMER
+
+#endif /* PLATFORM_DEF_H */
diff --git a/plat/marvell/armada/a3k/common/io_addr_dec.c b/plat/marvell/armada/a3k/common/io_addr_dec.c
new file mode 100644
index 0000000..fea7f81
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/io_addr_dec.c
@@ -0,0 +1,175 @@
+/*
+ * Copyright (C) 2016 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#include <lib/mmio.h>
+
+#include <io_addr_dec.h>
+#include <plat_marvell.h>
+
+#define MVEBU_DEC_WIN_CTRL_REG(base, win, off)	(MVEBU_REGS_BASE + (base) + \
+						(win) * (off))
+#define MVEBU_DEC_WIN_BASE_REG(base, win, off)	(MVEBU_REGS_BASE + (base) + \
+						(win) * (off) + 0x4)
+#define MVEBU_DEC_WIN_REMAP_REG(base, win, off)	(MVEBU_REGS_BASE + (base) + \
+						(win) * (off) + 0x8)
+
+#define MVEBU_DEC_WIN_CTRL_SIZE_OFF		(16)
+#define MVEBU_DEC_WIN_ENABLE			(0x1)
+#define MVEBU_DEC_WIN_CTRL_ATTR_OFF		(8)
+#define MVEBU_DEC_WIN_CTRL_TARGET_OFF		(4)
+#define MVEBU_DEC_WIN_CTRL_EN_OFF		(0)
+#define MVEBU_DEC_WIN_BASE_OFF			(16)
+
+#define MVEBU_WIN_BASE_SIZE_ALIGNMENT		(0x10000)
+
+/* There are up to 14 IO unit which need address decode in Armada-3700 */
+#define IO_UNIT_NUM_MAX				(14)
+
+#define MVEBU_MAX_ADDRSS_4GB			(0x100000000ULL)
+
+
+static void set_io_addr_dec_win(int win_id, uintptr_t base_addr,
+				uintptr_t win_size,
+				struct dec_win_config *dec_win)
+{
+	uint32_t ctrl = 0;
+	uint32_t base = 0;
+
+	/* set size */
+	ctrl = ((win_size / MVEBU_WIN_BASE_SIZE_ALIGNMENT) - 1) <<
+	       MVEBU_DEC_WIN_CTRL_SIZE_OFF;
+	/* set attr according to IO decode window */
+	ctrl |= dec_win->win_attr << MVEBU_DEC_WIN_CTRL_ATTR_OFF;
+	/* set target */
+	ctrl |= DRAM_CPU_DEC_TARGET_NUM << MVEBU_DEC_WIN_CTRL_TARGET_OFF;
+	/* set base */
+	base = (base_addr / MVEBU_WIN_BASE_SIZE_ALIGNMENT) <<
+	       MVEBU_DEC_WIN_BASE_OFF;
+
+	/* set base address*/
+	mmio_write_32(MVEBU_DEC_WIN_BASE_REG(dec_win->dec_reg_base,
+		      win_id, dec_win->win_offset),
+		      base);
+	/* set remap window, some unit does not have remap window */
+	if (win_id < dec_win->max_remap)
+		mmio_write_32(MVEBU_DEC_WIN_REMAP_REG(dec_win->dec_reg_base,
+			      win_id, dec_win->win_offset), base);
+	/* set control register */
+	mmio_write_32(MVEBU_DEC_WIN_CTRL_REG(dec_win->dec_reg_base,
+		      win_id, dec_win->win_offset), ctrl);
+	/* enable the address decode window at last to make it effective */
+	ctrl |= MVEBU_DEC_WIN_ENABLE << MVEBU_DEC_WIN_CTRL_EN_OFF;
+	mmio_write_32(MVEBU_DEC_WIN_CTRL_REG(dec_win->dec_reg_base,
+		      win_id, dec_win->win_offset), ctrl);
+
+	INFO("set_io_addr_dec %d result: ctrl(0x%x) base(0x%x) remap(0x%x)\n",
+	     win_id, mmio_read_32(MVEBU_DEC_WIN_CTRL_REG(dec_win->dec_reg_base,
+	     win_id, dec_win->win_offset)),
+	     mmio_read_32(MVEBU_DEC_WIN_BASE_REG(dec_win->dec_reg_base,
+			  win_id, dec_win->win_offset)),
+	     (win_id < dec_win->max_remap) ?
+		mmio_read_32(MVEBU_DEC_WIN_REMAP_REG(dec_win->dec_reg_base,
+			     win_id, dec_win->win_offset)) : 0);
+}
+
+/* Set io decode window */
+static int set_io_addr_dec(struct dram_win_map *win_map,
+			   struct dec_win_config *dec_win)
+{
+	struct dram_win *win;
+	int id;
+
+	/* disable all windows first */
+	for (id = 0; id < dec_win->max_dram_win; id++)
+		mmio_write_32(MVEBU_DEC_WIN_CTRL_REG(dec_win->dec_reg_base, id,
+			      dec_win->win_offset), 0);
+
+	/* configure IO decode windows for DRAM, inheritate DRAM size,
+	 * base and target from CPU-DRAM decode window and others
+	 * from hard coded IO decode window settings array.
+	 */
+	if (win_map->dram_win_num > dec_win->max_dram_win) {
+		/*
+		 * If cpu dram windows number exceeds the io decode windows
+		 * max number, then fill the first io decode window
+		 * with base(0) and size(4GB).
+		 */
+		set_io_addr_dec_win(0, 0, MVEBU_MAX_ADDRSS_4GB, dec_win);
+
+		return 0;
+	}
+
+	for (id = 0; id < win_map->dram_win_num; id++, win++) {
+		win = &win_map->dram_windows[id];
+		set_io_addr_dec_win(id, win->base_addr, win->win_size, dec_win);
+	}
+
+	return 0;
+}
+
+/*
+ * init_io_addr_dec
+ *
+ * This function initializes io address decoder windows by
+ * cpu dram window mapping information
+ *
+ * @input: N/A
+ *     - dram_wins_map: cpu dram windows mapping
+ *     - io_dec_config: io address decoder windows configuration
+ *     - io_unit_num: io address decoder unit number
+ * @output: N/A
+ *
+ * @return:  0 on success and others on failure
+ */
+int init_io_addr_dec(struct dram_win_map *dram_wins_map,
+		     struct dec_win_config *io_dec_config, uint32_t io_unit_num)
+{
+	int32_t index;
+	struct dec_win_config *io_dec_win;
+	int32_t ret;
+
+	INFO("Initializing IO address decode windows\n");
+
+	if (io_dec_config == NULL || io_unit_num == 0) {
+		ERROR("No IO address decoder windows configurations!\n");
+		return -1;
+	}
+
+	if (io_unit_num > IO_UNIT_NUM_MAX) {
+		ERROR("IO address decoder windows number %d is over max %d\n",
+		      io_unit_num, IO_UNIT_NUM_MAX);
+		return -1;
+	}
+
+	if (dram_wins_map == NULL) {
+		ERROR("No cpu dram decoder windows map!\n");
+		return -1;
+	}
+
+	for (index = 0; index < dram_wins_map->dram_win_num; index++)
+		INFO("DRAM mapping %d base(0x%lx) size(0x%lx)\n",
+		     index, dram_wins_map->dram_windows[index].base_addr,
+		     dram_wins_map->dram_windows[index].win_size);
+
+	/* Set address decode window for each IO */
+	for (index = 0; index < io_unit_num; index++) {
+		io_dec_win = io_dec_config + index;
+		ret = set_io_addr_dec(dram_wins_map, io_dec_win);
+		if (ret) {
+			ERROR("Failed to set IO address decode\n");
+			return -1;
+		}
+		INFO("Set IO decode window successfully, base(0x%x)"
+		     " win_attr(%x) max_dram_win(%d) max_remap(%d)"
+		     " win_offset(%d)\n", io_dec_win->dec_reg_base,
+		     io_dec_win->win_attr, io_dec_win->max_dram_win,
+		     io_dec_win->max_remap, io_dec_win->win_offset);
+	}
+
+	return 0;
+}
diff --git a/plat/marvell/armada/a3k/common/marvell_plat_config.c b/plat/marvell/armada/a3k/common/marvell_plat_config.c
new file mode 100644
index 0000000..3bf3d96
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/marvell_plat_config.c
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/bl_common.h>
+
+#include <io_addr_dec.h>
+#include <mvebu_def.h>
+
+struct dec_win_config io_dec_win_conf[] = {
+	/* dec_reg_base  win_attr  max_dram_win  max_remap  win_offset */
+	{0xc000,         0x3d,     2,       0,        0x08}, /* USB */
+	{0xc100,         0x3d,     3,       0,        0x10}, /* USB3 */
+	{0xc200,         0x3d,     2,       0,        0x10}, /* DMA */
+	{0xc300,         0x3d,     2,       0,        0x10}, /* NETA0 */
+	{0xc400,         0x3d,     2,       0,        0x10}, /* NETA1 */
+	{0xc500,         0x3d,     2,       0,        0x10}, /* PCIe */
+	{0xc800,         0x3d,     3,       0,        0x10}, /* SATA */
+	{0xca00,         0x3d,     3,       0,        0x08}, /* SD */
+	{0xcb00,         0x3d,     3,       0,        0x10}, /* eMMC */
+	{0xce00,	 0x3d,	   2,	    0,        0x08}, /* EIP97 */
+};
+
+int marvell_get_io_dec_win_conf(struct dec_win_config **win, uint32_t *size)
+{
+	*win = io_dec_win_conf;
+	*size = sizeof(io_dec_win_conf)/sizeof(struct dec_win_config);
+
+	return 0;
+}
+
diff --git a/plat/marvell/armada/a3k/common/plat_cci.c b/plat/marvell/armada/a3k/common/plat_cci.c
new file mode 100644
index 0000000..56f091f
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/plat_cci.c
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2021 Marek Behun <marek.behun@nic.cz>
+ *
+ * Based on plat/marvell/armada/common/marvell_cci.c
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <drivers/arm/cci.h>
+#include <lib/mmio.h>
+
+#include <plat_marvell.h>
+
+static const int cci_map[] = {
+	PLAT_MARVELL_CCI_CLUSTER0_SL_IFACE_IX,
+	PLAT_MARVELL_CCI_CLUSTER1_SL_IFACE_IX
+};
+
+/*
+ * This redefines the weak definition in
+ * plat/marvell/armada/common/marvell_cci.c
+ */
+void plat_marvell_interconnect_init(void)
+{
+	/*
+	 * To better utilize the address space, we remap CCI base address from
+	 * the default (0xD8000000) to MVEBU_CCI_BASE.
+	 * This has to be done here, rather than in cpu_wins_init(), because
+	 * cpu_wins_init() is called later.
+	 */
+	mmio_write_32(CPU_DEC_CCI_BASE_REG, MVEBU_CCI_BASE >> 20);
+
+	cci_init(PLAT_MARVELL_CCI_BASE, cci_map, ARRAY_SIZE(cci_map));
+}
diff --git a/plat/marvell/armada/a3k/common/plat_pm.c b/plat/marvell/armada/a3k/common/plat_pm.c
new file mode 100644
index 0000000..e2d15ab
--- /dev/null
+++ b/plat/marvell/armada/a3k/common/plat_pm.c
@@ -0,0 +1,822 @@
+/*
+ * Copyright (C) 2018-2020 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#ifdef USE_CCI
+#include <drivers/arm/cci.h>
+#endif
+#include <lib/psci/psci.h>
+#include <lib/mmio.h>
+#include <plat/common/platform.h>
+
+#include <a3700_pm.h>
+#include <arch_helpers.h>
+#include <armada_common.h>
+#include <dram_win.h>
+#include <io_addr_dec.h>
+#include <mvebu.h>
+#include <mvebu_def.h>
+#include <marvell_plat_priv.h>
+#include <plat_marvell.h>
+
+/* Warm reset register */
+#define MVEBU_WARM_RESET_REG		(MVEBU_NB_REGS_BASE + 0x840)
+#define MVEBU_WARM_RESET_MAGIC		0x1D1E
+
+/* North Bridge GPIO1 SEL register */
+#define MVEBU_NB_GPIO1_SEL_REG		(MVEBU_NB_REGS_BASE + 0x830)
+ #define MVEBU_NB_GPIO1_UART1_SEL	BIT(19)
+ #define MVEBU_NB_GPIO1_GPIO_25_26_EN	BIT(17)
+ #define MVEBU_NB_GPIO1_GPIO_19_EN	BIT(14)
+ #define MVEBU_NB_GPIO1_GPIO_18_EN	BIT(13)
+
+/* CPU 1 reset register */
+#define MVEBU_CPU_1_RESET_VECTOR	(MVEBU_REGS_BASE + 0x14044)
+#define MVEBU_CPU_1_RESET_REG		(MVEBU_REGS_BASE + 0xD00C)
+#define MVEBU_CPU_1_RESET_BIT		31
+
+/* IRQ register */
+#define MVEBU_NB_IRQ_STATUS_1_REG		(MVEBU_NB_SB_IRQ_REG_BASE)
+#define MVEBU_NB_IRQ_STATUS_2_REG		(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0x10)
+#define MVEBU_NB_IRQ_MASK_2_REG			(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0x18)
+#define MVEBU_SB_IRQ_STATUS_1_REG		(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0x40)
+#define MVEBU_SB_IRQ_STATUS_2_REG		(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0x50)
+#define MVEBU_NB_GPIO_IRQ_MASK_1_REG		(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0xC8)
+#define MVEBU_NB_GPIO_IRQ_MASK_2_REG		(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0xD8)
+#define MVEBU_SB_GPIO_IRQ_MASK_REG		(MVEBU_NB_SB_IRQ_REG_BASE + \
+						0xE8)
+#define MVEBU_NB_GPIO_IRQ_EN_LOW_REG		(MVEBU_NB_GPIO_IRQ_REG_BASE)
+#define MVEBU_NB_GPIO_IRQ_EN_HIGH_REG		(MVEBU_NB_GPIO_IRQ_REG_BASE + \
+						0x04)
+#define MVEBU_NB_GPIO_IRQ_STATUS_LOW_REG	(MVEBU_NB_GPIO_IRQ_REG_BASE + \
+						0x10)
+#define MVEBU_NB_GPIO_IRQ_STATUS_HIGH_REG	(MVEBU_NB_GPIO_IRQ_REG_BASE + \
+						0x14)
+#define MVEBU_NB_GPIO_IRQ_WK_LOW_REG		(MVEBU_NB_GPIO_IRQ_REG_BASE + \
+						0x18)
+#define MVEBU_NB_GPIO_IRQ_WK_HIGH_REG		(MVEBU_NB_GPIO_IRQ_REG_BASE + \
+						0x1C)
+#define MVEBU_SB_GPIO_IRQ_EN_REG		(MVEBU_SB_GPIO_IRQ_REG_BASE)
+#define MVEBU_SB_GPIO_IRQ_STATUS_REG		(MVEBU_SB_GPIO_IRQ_REG_BASE + \
+						0x10)
+#define MVEBU_SB_GPIO_IRQ_WK_REG		(MVEBU_SB_GPIO_IRQ_REG_BASE + \
+						0x18)
+
+/* PMU registers */
+#define MVEBU_PM_NB_PWR_CTRL_REG	(MVEBU_PMSU_REG_BASE)
+ #define MVEBU_PM_PWR_DN_CNT_SEL	BIT(28)
+ #define MVEBU_PM_SB_PWR_DWN		BIT(4)
+ #define MVEBU_PM_INTERFACE_IDLE	BIT(0)
+#define MVEBU_PM_NB_CPU_PWR_CTRL_REG	(MVEBU_PMSU_REG_BASE + 0x4)
+ #define MVEBU_PM_L2_FLUSH_EN		BIT(22)
+#define MVEBU_PM_NB_PWR_OPTION_REG	(MVEBU_PMSU_REG_BASE + 0x8)
+ #define MVEBU_PM_DDR_SR_EN		BIT(29)
+ #define MVEBU_PM_DDR_CLK_DIS_EN	BIT(28)
+ #define MVEBU_PM_WARM_RESET_EN		BIT(27)
+ #define MVEBU_PM_DDRPHY_PWRDWN_EN	BIT(23)
+ #define MVEBU_PM_DDRPHY_PAD_PWRDWN_EN	BIT(22)
+ #define MVEBU_PM_OSC_OFF_EN		BIT(21)
+ #define MVEBU_PM_TBG_OFF_EN		BIT(20)
+ #define MVEBU_PM_CPU_VDDV_OFF_EN	BIT(19)
+ #define MVEBU_PM_AVS_DISABLE_MODE	BIT(14)
+ #define MVEBU_PM_AVS_VDD2_MODE		BIT(13)
+ #define MVEBU_PM_AVS_HOLD_MODE		BIT(12)
+ #define MVEBU_PM_L2_SRAM_LKG_PD_EN	BIT(8)
+ #define MVEBU_PM_EIP_SRAM_LKG_PD_EN	BIT(7)
+ #define MVEBU_PM_DDRMC_SRAM_LKG_PD_EN	BIT(6)
+ #define MVEBU_PM_MCI_SRAM_LKG_PD_EN	BIT(5)
+ #define MVEBU_PM_MMC_SRAM_LKG_PD_EN	BIT(4)
+ #define MVEBU_PM_SATA_SRAM_LKG_PD_EN	BIT(3)
+ #define MVEBU_PM_DMA_SRAM_LKG_PD_EN	BIT(2)
+ #define MVEBU_PM_SEC_SRAM_LKG_PD_EN	BIT(1)
+ #define MVEBU_PM_CPU_SRAM_LKG_PD_EN	BIT(0)
+ #define MVEBU_PM_NB_SRAM_LKG_PD_EN	(MVEBU_PM_L2_SRAM_LKG_PD_EN |\
+	MVEBU_PM_EIP_SRAM_LKG_PD_EN | MVEBU_PM_DDRMC_SRAM_LKG_PD_EN |\
+	MVEBU_PM_MCI_SRAM_LKG_PD_EN | MVEBU_PM_MMC_SRAM_LKG_PD_EN |\
+	MVEBU_PM_SATA_SRAM_LKG_PD_EN | MVEBU_PM_DMA_SRAM_LKG_PD_EN |\
+	MVEBU_PM_SEC_SRAM_LKG_PD_EN | MVEBU_PM_CPU_SRAM_LKG_PD_EN)
+#define MVEBU_PM_NB_PWR_DEBUG_REG	(MVEBU_PMSU_REG_BASE + 0xC)
+ #define MVEBU_PM_NB_FORCE_CLK_ON	BIT(30)
+ #define MVEBU_PM_IGNORE_CM3_SLEEP	BIT(21)
+ #define MVEBU_PM_IGNORE_CM3_DEEP	BIT(20)
+#define MVEBU_PM_NB_WAKE_UP_EN_REG	(MVEBU_PMSU_REG_BASE + 0x2C)
+ #define MVEBU_PM_SB_WKP_NB_EN		BIT(31)
+ #define MVEBU_PM_NB_GPIO_WKP_EN	BIT(27)
+ #define MVEBU_PM_SOC_TIMER_WKP_EN	BIT(26)
+ #define MVEBU_PM_UART_WKP_EN		BIT(25)
+ #define MVEBU_PM_UART2_WKP_EN		BIT(19)
+ #define MVEBU_PM_CPU_TIMER_WKP_EN	BIT(17)
+ #define MVEBU_PM_NB_WKP_EN		BIT(16)
+ #define MVEBU_PM_CORE1_FIQ_IRQ_WKP_EN	BIT(13)
+ #define MVEBU_PM_CORE0_FIQ_IRQ_WKP_EN	BIT(12)
+#define MVEBU_PM_CPU_0_PWR_CTRL_REG	(MVEBU_PMSU_REG_BASE + 0x34)
+#define MVEBU_PM_CPU_1_PWR_CTRL_REG	(MVEBU_PMSU_REG_BASE + 0x38)
+ #define MVEBU_PM_CORE_SOC_PD		BIT(2)
+ #define MVEBU_PM_CORE_PROC_PD		BIT(1)
+ #define MVEBU_PM_CORE_PD		BIT(0)
+#define MVEBU_PM_CORE_1_RETURN_ADDR_REG	(MVEBU_PMSU_REG_BASE + 0x44)
+#define MVEBU_PM_CPU_VDD_OFF_INFO_1_REG	(MVEBU_PMSU_REG_BASE + 0x48)
+#define MVEBU_PM_CPU_VDD_OFF_INFO_2_REG	(MVEBU_PMSU_REG_BASE + 0x4C)
+ #define MVEBU_PM_LOW_POWER_STATE	BIT(0)
+#define MVEBU_PM_CPU_WAKE_UP_CONF_REG	(MVEBU_PMSU_REG_BASE + 0x54)
+ #define MVEBU_PM_CORE1_WAKEUP		BIT(13)
+ #define MVEBU_PM_CORE0_WAKEUP		BIT(12)
+#define MVEBU_PM_WAIT_DDR_RDY_VALUE	(0x15)
+#define MVEBU_PM_SB_CPU_PWR_CTRL_REG	(MVEBU_SB_WAKEUP_REG_BASE)
+  #define MVEBU_PM_SB_PM_START		BIT(0)
+#define MVEBU_PM_SB_PWR_OPTION_REG	(MVEBU_SB_WAKEUP_REG_BASE + 0x4)
+  #define MVEBU_PM_SDIO_PHY_PDWN_EN	BIT(17)
+  #define MVEBU_PM_SB_VDDV_OFF_EN	BIT(16)
+  #define MVEBU_PM_EBM_SRAM_LKG_PD_EN		BIT(11)
+  #define MVEBU_PM_PCIE_SRAM_LKG_PD_EN		BIT(10)
+  #define MVEBU_PM_GBE1_TX_SRAM_LKG_PD_EN	BIT(9)
+  #define MVEBU_PM_GBE1_RX_SRAM_LKG_PD_EN	BIT(8)
+  #define MVEBU_PM_GBE1_MIB_SRAM_LKG_PD_EN	BIT(7)
+  #define MVEBU_PM_GBE0_TX_SRAM_LKG_PD_EN	BIT(6)
+  #define MVEBU_PM_GBE0_RX_SRAM_LKG_PD_EN	BIT(5)
+  #define MVEBU_PM_GBE0_MIB_SRAM_LKG_PD_EN	BIT(4)
+  #define MVEBU_PM_SDIO_SRAM_LKG_PD_EN		BIT(3)
+  #define MVEBU_PM_USB2_SRAM_LKG_PD_EN		BIT(2)
+  #define MVEBU_PM_USB3_H_SRAM_LKG_PD_EN	BIT(1)
+  #define MVEBU_PM_SB_SRAM_LKG_PD_EN	(MVEBU_PM_EBM_SRAM_LKG_PD_EN |\
+	MVEBU_PM_PCIE_SRAM_LKG_PD_EN | MVEBU_PM_GBE1_TX_SRAM_LKG_PD_EN |\
+	MVEBU_PM_GBE1_RX_SRAM_LKG_PD_EN | MVEBU_PM_GBE1_MIB_SRAM_LKG_PD_EN |\
+	MVEBU_PM_GBE0_TX_SRAM_LKG_PD_EN | MVEBU_PM_GBE0_RX_SRAM_LKG_PD_EN |\
+	MVEBU_PM_GBE0_MIB_SRAM_LKG_PD_EN | MVEBU_PM_SDIO_SRAM_LKG_PD_EN |\
+	MVEBU_PM_USB2_SRAM_LKG_PD_EN | MVEBU_PM_USB3_H_SRAM_LKG_PD_EN)
+#define MVEBU_PM_SB_WK_EN_REG		(MVEBU_SB_WAKEUP_REG_BASE + 0x10)
+  #define MVEBU_PM_SB_GPIO_WKP_EN	BIT(24)
+  #define MVEBU_PM_SB_WKP_EN		BIT(20)
+
+/* DRAM registers */
+#define MVEBU_DRAM_STATS_CH0_REG	(MVEBU_DRAM_REG_BASE + 0x4)
+ #define MVEBU_DRAM_WCP_EMPTY		BIT(19)
+#define MVEBU_DRAM_CMD_0_REG		(MVEBU_DRAM_REG_BASE + 0x20)
+ #define MVEBU_DRAM_CH0_CMD0		BIT(28)
+ #define MVEBU_DRAM_CS_CMD0		BIT(24)
+ #define MVEBU_DRAM_WCB_DRAIN_REQ	BIT(1)
+#define MVEBU_DRAM_PWR_CTRL_REG		(MVEBU_DRAM_REG_BASE + 0x54)
+ #define MVEBU_DRAM_PHY_CLK_GATING_EN	BIT(1)
+ #define MVEBU_DRAM_PHY_AUTO_AC_OFF_EN	BIT(0)
+
+/* AVS registers */
+#define MVEBU_AVS_CTRL_2_REG		(MVEBU_AVS_REG_BASE + 0x8)
+ #define MVEBU_LOW_VDD_MODE_EN		BIT(6)
+
+/* Clock registers */
+#define MVEBU_NB_CLOCK_SEL_REG		(MVEBU_NB_REGS_BASE + 0x10)
+ #define MVEBU_A53_CPU_CLK_SEL		BIT(15)
+
+/* North Bridge Step-Down Registers */
+#define MVEBU_NB_STEP_DOWN_INT_EN_REG	MVEBU_NB_STEP_DOWN_REG_BASE
+ #define MVEBU_NB_GPIO_INT_WAKE_WCPU_CLK	BIT(8)
+
+#define MVEBU_NB_GPIO_18	18
+#define MVEBU_NB_GPIO_19	19
+#define MVEBU_NB_GPIO_25	25
+#define MVEBU_NB_GPIO_26	26
+
+typedef int (*wake_up_src_func)(union pm_wake_up_src_data *);
+
+struct wake_up_src_func_map {
+	enum pm_wake_up_src_type type;
+	wake_up_src_func func;
+};
+
+void marvell_psci_arch_init(int die_index)
+{
+}
+
+static void a3700_pm_ack_irq(void)
+{
+	uint32_t reg;
+
+	reg = mmio_read_32(MVEBU_NB_IRQ_STATUS_1_REG);
+	if (reg)
+		mmio_write_32(MVEBU_NB_IRQ_STATUS_1_REG, reg);
+
+	reg = mmio_read_32(MVEBU_NB_IRQ_STATUS_2_REG);
+	if (reg)
+		mmio_write_32(MVEBU_NB_IRQ_STATUS_2_REG, reg);
+
+	reg = mmio_read_32(MVEBU_SB_IRQ_STATUS_1_REG);
+	if (reg)
+		mmio_write_32(MVEBU_SB_IRQ_STATUS_1_REG, reg);
+
+	reg = mmio_read_32(MVEBU_SB_IRQ_STATUS_2_REG);
+	if (reg)
+		mmio_write_32(MVEBU_SB_IRQ_STATUS_2_REG, reg);
+
+	reg = mmio_read_32(MVEBU_NB_GPIO_IRQ_STATUS_LOW_REG);
+	if (reg)
+		mmio_write_32(MVEBU_NB_GPIO_IRQ_STATUS_LOW_REG, reg);
+
+	reg = mmio_read_32(MVEBU_NB_GPIO_IRQ_STATUS_HIGH_REG);
+	if (reg)
+		mmio_write_32(MVEBU_NB_GPIO_IRQ_STATUS_HIGH_REG, reg);
+
+	reg = mmio_read_32(MVEBU_SB_GPIO_IRQ_STATUS_REG);
+	if (reg)
+		mmio_write_32(MVEBU_SB_GPIO_IRQ_STATUS_REG, reg);
+}
+
+/*****************************************************************************
+ * A3700 handler called to check the validity of the power state
+ * parameter.
+ *****************************************************************************
+ */
+int a3700_validate_power_state(unsigned int power_state,
+			       psci_power_state_t *req_state)
+{
+	ERROR("%s needs to be implemented\n", __func__);
+	panic();
+}
+
+/*****************************************************************************
+ * A3700 handler called when a CPU is about to enter standby.
+ *****************************************************************************
+ */
+void a3700_cpu_standby(plat_local_state_t cpu_state)
+{
+	ERROR("%s needs to be implemented\n", __func__);
+	panic();
+}
+
+/*****************************************************************************
+ * A3700 handler called when a power domain is about to be turned on. The
+ * mpidr determines the CPU to be turned on.
+ *****************************************************************************
+ */
+int a3700_pwr_domain_on(u_register_t mpidr)
+{
+	/* Set barrier */
+	dsbsy();
+
+	/* Set the cpu start address to BL1 entry point */
+	mmio_write_32(MVEBU_CPU_1_RESET_VECTOR,
+		      PLAT_MARVELL_CPU_ENTRY_ADDR >> 2);
+
+	/* Get the cpu out of reset */
+	mmio_clrbits_32(MVEBU_CPU_1_RESET_REG, BIT(MVEBU_CPU_1_RESET_BIT));
+	mmio_setbits_32(MVEBU_CPU_1_RESET_REG, BIT(MVEBU_CPU_1_RESET_BIT));
+
+	return 0;
+}
+
+/*****************************************************************************
+ * A3700 handler called to validate the entry point.
+ *****************************************************************************
+ */
+int a3700_validate_ns_entrypoint(uintptr_t entrypoint)
+{
+	return PSCI_E_SUCCESS;
+}
+
+/*****************************************************************************
+ * A3700 handler called when a power domain is about to be turned off. The
+ * target_state encodes the power state that each level should transition to.
+ *****************************************************************************
+ */
+void a3700_pwr_domain_off(const psci_power_state_t *target_state)
+{
+	/* Prevent interrupts from spuriously waking up this cpu */
+	plat_marvell_gic_cpuif_disable();
+
+	/* Core can not be powered down with pending IRQ,
+	 * acknowledge all the pending IRQ
+	 */
+	a3700_pm_ack_irq();
+}
+
+static void a3700_set_gen_pwr_off_option(void)
+{
+	/* Enable L2 flush -> processor state-machine option */
+	mmio_setbits_32(MVEBU_PM_NB_CPU_PWR_CTRL_REG, MVEBU_PM_L2_FLUSH_EN);
+
+	/*
+	 * North bridge cannot be VDD off (always ON).
+	 * The NB state machine support low power mode by its state machine.
+	 * This bit MUST be set for north bridge power down, e.g.,
+	 * OSC input cutoff(NOT TEST), SRAM power down, PMIC, etc.
+	 * It is not related to CPU VDD OFF!!
+	 */
+	mmio_clrbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_CPU_VDDV_OFF_EN);
+
+	/*
+	 * MUST: Switch CPU/AXI clock to OSC
+	 * NB state machine clock is always connected to OSC (slow clock).
+	 * But Core0/1/processor state machine's clock are connected to AXI
+	 *  clock. Now, AXI clock takes the TBG as clock source.
+	 * If using AXI clock, Core0/1/processor state machine may much faster
+	 * than NB state machine. It will cause problem in this case if cores
+	 * are released before north bridge gets ready.
+	 */
+	mmio_clrbits_32(MVEBU_NB_CLOCK_SEL_REG, MVEBU_A53_CPU_CLK_SEL);
+
+	/*
+	 * These register bits will trigger north bridge
+	 * power-down state machine regardless CM3 status.
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_DEBUG_REG, MVEBU_PM_IGNORE_CM3_SLEEP);
+	mmio_setbits_32(MVEBU_PM_NB_PWR_DEBUG_REG, MVEBU_PM_IGNORE_CM3_DEEP);
+
+	/*
+	 * SRAM => controlled by north bridge state machine.
+	 * Core VDD OFF is not related to CPU SRAM power down.
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_NB_SRAM_LKG_PD_EN);
+
+	/*
+	 * Idle AXI interface in order to get L2_WFI
+	 * L2 WFI is only asserted after CORE-0 and CORE-1 WFI asserted.
+	 * (only both core-0/1in WFI, L2 WFI will be issued by CORE.)
+	 * Once L2 WFI asserted, this bit is used for signalling assertion
+	 * to AXI IO masters.
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_CTRL_REG, MVEBU_PM_INTERFACE_IDLE);
+
+	/* Enable core0 and core1 VDD_OFF */
+	mmio_setbits_32(MVEBU_PM_CPU_0_PWR_CTRL_REG, MVEBU_PM_CORE_PD);
+	mmio_setbits_32(MVEBU_PM_CPU_1_PWR_CTRL_REG, MVEBU_PM_CORE_PD);
+
+	/* Enable North bridge power down -
+	 * Both Cores MUST enable this bit to power down north bridge!
+	 */
+	mmio_setbits_32(MVEBU_PM_CPU_0_PWR_CTRL_REG, MVEBU_PM_CORE_SOC_PD);
+	mmio_setbits_32(MVEBU_PM_CPU_1_PWR_CTRL_REG, MVEBU_PM_CORE_SOC_PD);
+
+	/* CA53 (processor domain) power down */
+	mmio_setbits_32(MVEBU_PM_CPU_0_PWR_CTRL_REG, MVEBU_PM_CORE_PROC_PD);
+	mmio_setbits_32(MVEBU_PM_CPU_1_PWR_CTRL_REG, MVEBU_PM_CORE_PROC_PD);
+}
+
+static void a3700_en_ddr_self_refresh(void)
+{
+	/*
+	 * Both count is 16 bits and configurable. By default, osc stb cnt
+	 * is 0xFFF for lower 12 bits.
+	 * Thus, powerdown count is smaller than osc count.
+	 * This count is used for exiting DDR SR mode on wakeup event.
+	 * The powerdown count also has impact on the following
+	 * state changes: idle -> count-down -> ... (power-down, vdd off, etc)
+	 * Here, make stable counter shorter
+	 * Use power down count value instead of osc_stb_cnt to speed up
+	 * DDR self refresh exit
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_CTRL_REG, MVEBU_PM_PWR_DN_CNT_SEL);
+
+	/*
+	 * Enable DDR SR mode => controlled by north bridge state machine
+	 * Therefore, we must powerdown north bridge to trigger the DDR SR
+	 * mode switching.
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDR_SR_EN);
+	/* Disable DDR clock, otherwise DDR will not enter into SR mode. */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDR_CLK_DIS_EN);
+	/* Power down DDR PHY (PAD) */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_DDRPHY_PWRDWN_EN);
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG,
+			MVEBU_PM_DDRPHY_PAD_PWRDWN_EN);
+
+	/* Set wait time for DDR ready in ROM code */
+	mmio_write_32(MVEBU_PM_CPU_VDD_OFF_INFO_1_REG,
+		      MVEBU_PM_WAIT_DDR_RDY_VALUE);
+
+	/* DDR flush write buffer - mandatory */
+	mmio_write_32(MVEBU_DRAM_CMD_0_REG, MVEBU_DRAM_CH0_CMD0 |
+		      MVEBU_DRAM_CS_CMD0 | MVEBU_DRAM_WCB_DRAIN_REQ);
+	while ((mmio_read_32(MVEBU_DRAM_STATS_CH0_REG) &
+			     MVEBU_DRAM_WCP_EMPTY) != MVEBU_DRAM_WCP_EMPTY)
+		;
+
+	/* Trigger PHY reset after ddr out of self refresh =>
+	 * supply reset pulse for DDR phy after wake up
+	 */
+	mmio_setbits_32(MVEBU_DRAM_PWR_CTRL_REG, MVEBU_DRAM_PHY_CLK_GATING_EN |
+						 MVEBU_DRAM_PHY_AUTO_AC_OFF_EN);
+}
+
+static void a3700_pwr_dn_avs(void)
+{
+	/*
+	 * AVS power down - controlled by north bridge statemachine
+	 * Enable AVS power down by clear the AVS disable bit.
+	 */
+	mmio_clrbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_AVS_DISABLE_MODE);
+	/*
+	 * Should set BIT[12:13] to powerdown AVS.
+	 * 1. Enable AVS VDD2 mode
+	 * 2. After power down AVS, we must hold AVS output voltage.
+	 * 3. We can choose the lower VDD for AVS power down.
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_AVS_VDD2_MODE);
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_AVS_HOLD_MODE);
+
+	/* Enable low VDD mode, AVS will set CPU to lowest core VDD 747mV */
+	mmio_setbits_32(MVEBU_AVS_CTRL_2_REG, MVEBU_LOW_VDD_MODE_EN);
+}
+
+static void a3700_pwr_dn_tbg(void)
+{
+	/* Power down TBG */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_TBG_OFF_EN);
+}
+
+static void a3700_pwr_dn_sb(void)
+{
+	/* Enable south bridge power down option */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_CTRL_REG, MVEBU_PM_SB_PWR_DWN);
+
+	/* Enable SDIO_PHY_PWRDWN */
+	mmio_setbits_32(MVEBU_PM_SB_PWR_OPTION_REG, MVEBU_PM_SDIO_PHY_PDWN_EN);
+
+	/* Enable SRAM LRM on SB */
+	mmio_setbits_32(MVEBU_PM_SB_PWR_OPTION_REG, MVEBU_PM_SB_SRAM_LKG_PD_EN);
+
+	/* Enable SB Power Off */
+	mmio_setbits_32(MVEBU_PM_SB_PWR_OPTION_REG, MVEBU_PM_SB_VDDV_OFF_EN);
+
+	/* Kick off South Bridge Power Off */
+	mmio_setbits_32(MVEBU_PM_SB_CPU_PWR_CTRL_REG, MVEBU_PM_SB_PM_START);
+}
+
+static void a3700_set_pwr_off_option(void)
+{
+	/* Set general power off option */
+	a3700_set_gen_pwr_off_option();
+
+	/* Enable DDR self refresh in low power mode */
+	a3700_en_ddr_self_refresh();
+
+	/* Power down AVS */
+	a3700_pwr_dn_avs();
+
+	/* Power down TBG */
+	a3700_pwr_dn_tbg();
+
+	/* Power down south bridge, pay attention south bridge setting
+	 * should be done before
+	 */
+	a3700_pwr_dn_sb();
+}
+
+static void a3700_set_wake_up_option(void)
+{
+	/*
+	 * Enable the wakeup event for NB SOC => north-bridge
+	 * state-machine enablement on wake-up event
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_WAKE_UP_EN_REG, MVEBU_PM_NB_WKP_EN);
+
+	 /* Enable both core0 and core1 wakeup on demand */
+	mmio_setbits_32(MVEBU_PM_CPU_WAKE_UP_CONF_REG,
+			MVEBU_PM_CORE1_WAKEUP | MVEBU_PM_CORE0_WAKEUP);
+
+	/* Enable warm reset in low power mode */
+	mmio_setbits_32(MVEBU_PM_NB_PWR_OPTION_REG, MVEBU_PM_WARM_RESET_EN);
+}
+
+static void a3700_pm_en_nb_gpio(uint32_t gpio)
+{
+	/* For GPIO1 interrupt -- North bridge only */
+	if (gpio >= 32) {
+		/* GPIO int mask */
+		mmio_clrbits_32(MVEBU_NB_GPIO_IRQ_MASK_2_REG, BIT(gpio - 32));
+
+		/* NB_CPU_WAKE-up ENABLE GPIO int */
+		mmio_setbits_32(MVEBU_NB_GPIO_IRQ_EN_HIGH_REG, BIT(gpio - 32));
+	} else {
+		/* GPIO int mask */
+		mmio_clrbits_32(MVEBU_NB_GPIO_IRQ_MASK_1_REG, BIT(gpio));
+
+		/* NB_CPU_WAKE-up ENABLE GPIO int */
+		mmio_setbits_32(MVEBU_NB_GPIO_IRQ_EN_LOW_REG, BIT(gpio));
+	}
+
+	mmio_setbits_32(MVEBU_NB_STEP_DOWN_INT_EN_REG,
+			MVEBU_NB_GPIO_INT_WAKE_WCPU_CLK);
+
+	/* Enable using GPIO as wakeup event
+	 * (actually not only for north bridge)
+	 */
+	mmio_setbits_32(MVEBU_PM_NB_WAKE_UP_EN_REG, MVEBU_PM_NB_GPIO_WKP_EN |
+		MVEBU_PM_NB_WKP_EN | MVEBU_PM_CORE1_FIQ_IRQ_WKP_EN |
+		MVEBU_PM_CORE0_FIQ_IRQ_WKP_EN);
+}
+
+static void a3700_pm_en_sb_gpio(uint32_t gpio)
+{
+	/* Enable using GPIO as wakeup event */
+	mmio_setbits_32(MVEBU_PM_NB_WAKE_UP_EN_REG, MVEBU_PM_SB_WKP_NB_EN |
+		MVEBU_PM_NB_WKP_EN | MVEBU_PM_CORE1_FIQ_IRQ_WKP_EN |
+		MVEBU_PM_CORE0_FIQ_IRQ_WKP_EN);
+
+	/* SB GPIO Wake UP | South Bridge Wake Up Enable */
+	mmio_setbits_32(MVEBU_PM_SB_WK_EN_REG, MVEBU_PM_SB_GPIO_WKP_EN |
+			MVEBU_PM_SB_GPIO_WKP_EN);
+
+	/* GPIO int mask */
+	mmio_clrbits_32(MVEBU_SB_GPIO_IRQ_MASK_REG, BIT(gpio));
+
+	/* NB_CPU_WAKE-up ENABLE GPIO int */
+	mmio_setbits_32(MVEBU_SB_GPIO_IRQ_EN_REG, BIT(gpio));
+}
+
+int a3700_pm_src_gpio(union pm_wake_up_src_data *src_data)
+{
+	if (src_data->gpio_data.bank_num == 0)
+		/* North Bridge GPIO */
+		a3700_pm_en_nb_gpio(src_data->gpio_data.gpio_num);
+	else
+		a3700_pm_en_sb_gpio(src_data->gpio_data.gpio_num);
+	return 0;
+}
+
+int a3700_pm_src_uart1(union pm_wake_up_src_data *src_data)
+{
+	/* Clear Uart1 select */
+	mmio_clrbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_UART1_SEL);
+	/* set pin 19 gpio usage*/
+	mmio_setbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_GPIO_19_EN);
+	/* Enable gpio wake-up*/
+	a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_19);
+	/* set pin 18 gpio usage*/
+	mmio_setbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_GPIO_18_EN);
+	/* Enable gpio wake-up*/
+	a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_18);
+
+	return 0;
+}
+
+int a3700_pm_src_uart0(union pm_wake_up_src_data *src_data)
+{
+	/* set pin 25/26 gpio usage*/
+	mmio_setbits_32(MVEBU_NB_GPIO1_SEL_REG, MVEBU_NB_GPIO1_GPIO_25_26_EN);
+	/* Enable gpio wake-up*/
+	a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_25);
+	/* Enable gpio wake-up*/
+	a3700_pm_en_nb_gpio(MVEBU_NB_GPIO_26);
+
+	return 0;
+}
+
+struct wake_up_src_func_map src_func_table[WAKE_UP_SRC_MAX] = {
+	{WAKE_UP_SRC_GPIO, a3700_pm_src_gpio},
+	{WAKE_UP_SRC_UART1, a3700_pm_src_uart1},
+	{WAKE_UP_SRC_UART0, a3700_pm_src_uart0},
+	/* FOLLOWING SRC NOT SUPPORTED YET */
+	{WAKE_UP_SRC_TIMER, NULL}
+};
+
+static wake_up_src_func a3700_get_wake_up_src_func(
+						  enum pm_wake_up_src_type type)
+{
+	uint32_t loop;
+
+	for (loop = 0; loop < WAKE_UP_SRC_MAX; loop++) {
+		if (src_func_table[loop].type == type)
+			return src_func_table[loop].func;
+	}
+	return NULL;
+}
+
+#pragma weak mv_wake_up_src_config_get
+struct pm_wake_up_src_config *mv_wake_up_src_config_get(void)
+{
+	static struct pm_wake_up_src_config wake_up_src_cfg = {};
+	return &wake_up_src_cfg;
+}
+
+static void a3700_set_wake_up_source(void)
+{
+	struct pm_wake_up_src_config *wake_up_src;
+	uint32_t loop;
+	wake_up_src_func src_func = NULL;
+
+	wake_up_src = mv_wake_up_src_config_get();
+	for (loop = 0; loop < wake_up_src->wake_up_src_num; loop++) {
+		src_func = a3700_get_wake_up_src_func(
+			   wake_up_src->wake_up_src[loop].wake_up_src_type);
+		if (src_func)
+			src_func(
+				&(wake_up_src->wake_up_src[loop].wake_up_data));
+	}
+}
+
+static void a3700_pm_save_lp_flag(void)
+{
+	/* Save the flag for enter the low power mode */
+	mmio_setbits_32(MVEBU_PM_CPU_VDD_OFF_INFO_2_REG,
+			MVEBU_PM_LOW_POWER_STATE);
+}
+
+static void a3700_pm_clear_lp_flag(void)
+{
+	/* Clear the flag for enter the low power mode */
+	mmio_clrbits_32(MVEBU_PM_CPU_VDD_OFF_INFO_2_REG,
+			MVEBU_PM_LOW_POWER_STATE);
+}
+
+static uint32_t a3700_pm_get_lp_flag(void)
+{
+	/* Get the flag for enter the low power mode */
+	return mmio_read_32(MVEBU_PM_CPU_VDD_OFF_INFO_2_REG) &
+			    MVEBU_PM_LOW_POWER_STATE;
+}
+
+/*****************************************************************************
+ * A3700 handler called when a power domain is about to be suspended. The
+ * target_state encodes the power state that each level should transition to.
+ *****************************************************************************
+ */
+void a3700_pwr_domain_suspend(const psci_power_state_t *target_state)
+{
+	/* Prevent interrupts from spuriously waking up this cpu */
+	plat_marvell_gic_cpuif_disable();
+
+	/* Save IRQ states */
+	plat_marvell_gic_irq_save();
+
+	/* Set wake up options */
+	a3700_set_wake_up_option();
+
+	/* Set wake up sources */
+	a3700_set_wake_up_source();
+
+	/* SoC can not be powered down with pending IRQ,
+	 * acknowledge all the pending IRQ
+	 */
+	a3700_pm_ack_irq();
+
+	/* Set power off options */
+	a3700_set_pwr_off_option();
+
+	/* Save the flag for enter the low power mode */
+	a3700_pm_save_lp_flag();
+
+	isb();
+}
+
+/*****************************************************************************
+ * A3700 handler called when a power domain has just been powered on after
+ * being turned off earlier. The target_state encodes the low power state that
+ * each level has woken up from.
+ *****************************************************************************
+ */
+void a3700_pwr_domain_on_finish(const psci_power_state_t *target_state)
+{
+	/* arch specific configuration */
+	marvell_psci_arch_init(0);
+
+	/* Per-CPU interrupt initialization */
+	plat_marvell_gic_pcpu_init();
+	plat_marvell_gic_cpuif_enable();
+
+	/* Restore the per-cpu IRQ state */
+	if (a3700_pm_get_lp_flag())
+		plat_marvell_gic_irq_pcpu_restore();
+}
+
+/*****************************************************************************
+ * A3700 handler called when a power domain has just been powered on after
+ * having been suspended earlier. The target_state encodes the low power state
+ * that each level has woken up from.
+ * TODO: At the moment we reuse the on finisher and reinitialize the secure
+ * context. Need to implement a separate suspend finisher.
+ *****************************************************************************
+ */
+void a3700_pwr_domain_suspend_finish(const psci_power_state_t *target_state)
+{
+	struct dec_win_config *io_dec_map;
+	uint32_t dec_win_num;
+	struct dram_win_map dram_wins_map;
+
+	/* arch specific configuration */
+	marvell_psci_arch_init(0);
+
+	/* Interrupt initialization */
+	plat_marvell_gic_init();
+
+	/* Restore IRQ states */
+	plat_marvell_gic_irq_restore();
+
+	/*
+	 * Initialize CCI for this cluster after resume from suspend state.
+	 * No need for locks as no other CPU is active.
+	 */
+	plat_marvell_interconnect_init();
+	/*
+	 * Enable CCI coherency for the primary CPU's cluster.
+	 * Platform specific PSCI code will enable coherency for other
+	 * clusters.
+	 */
+	plat_marvell_interconnect_enter_coherency();
+
+	/* CPU address decoder windows initialization. */
+	cpu_wins_init();
+
+	/* fetch CPU-DRAM window mapping information by reading
+	 * CPU-DRAM decode windows (only the enabled ones)
+	 */
+	dram_win_map_build(&dram_wins_map);
+
+	/* Get IO address decoder windows */
+	if (marvell_get_io_dec_win_conf(&io_dec_map, &dec_win_num)) {
+		printf("No IO address decoder windows configurations found!\n");
+		return;
+	}
+
+	/* IO address decoder init */
+	if (init_io_addr_dec(&dram_wins_map, io_dec_map, dec_win_num)) {
+		printf("IO address decoder windows initialization failed!\n");
+		return;
+	}
+
+	/* Clear low power mode flag */
+	a3700_pm_clear_lp_flag();
+}
+
+/*****************************************************************************
+ * This handler is called by the PSCI implementation during the `SYSTEM_SUSPEND
+ * call to get the `power_state` parameter. This allows the platform to encode
+ * the appropriate State-ID field within the `power_state` parameter which can
+ * be utilized in `pwr_domain_suspend()` to suspend to system affinity level.
+ *****************************************************************************
+ */
+void a3700_get_sys_suspend_power_state(psci_power_state_t *req_state)
+{
+	/* lower affinities use PLAT_MAX_OFF_STATE */
+	for (int i = MPIDR_AFFLVL0; i <= PLAT_MAX_PWR_LVL; i++)
+		req_state->pwr_domain_state[i] = PLAT_MAX_OFF_STATE;
+}
+
+/*****************************************************************************
+ * A3700 handlers to shutdown/reboot the system
+ *****************************************************************************
+ */
+static void __dead2 a3700_system_off(void)
+{
+	ERROR("%s needs to be implemented\n", __func__);
+	panic();
+}
+
+#pragma weak cm3_system_reset
+void cm3_system_reset(void)
+{
+}
+
+/*****************************************************************************
+ * A3700 handlers to reset the system
+ *****************************************************************************
+ */
+static void __dead2 a3700_system_reset(void)
+{
+	/* Clean the mailbox magic number to let it as act like cold boot */
+	mmio_write_32(PLAT_MARVELL_MAILBOX_BASE, 0x0);
+
+	dsbsy();
+
+	/* Flush data cache if the mail box shared RAM is cached */
+#if PLAT_MARVELL_SHARED_RAM_CACHED
+	flush_dcache_range((uintptr_t)PLAT_MARVELL_MAILBOX_BASE,
+			   2 * sizeof(uint64_t));
+#endif
+
+	/* Use Cortex-M3 secure coprocessor for system reset */
+	cm3_system_reset();
+
+	/* Trigger the warm reset */
+	mmio_write_32(MVEBU_WARM_RESET_REG, MVEBU_WARM_RESET_MAGIC);
+
+	/* Shouldn't get to this point */
+	panic();
+}
+
+/*****************************************************************************
+ * Export the platform handlers via plat_arm_psci_pm_ops. The ARM Standard
+ * platform layer will take care of registering the handlers with PSCI.
+ *****************************************************************************
+ */
+const plat_psci_ops_t plat_arm_psci_pm_ops = {
+	.cpu_standby = a3700_cpu_standby,
+	.pwr_domain_on = a3700_pwr_domain_on,
+	.pwr_domain_off = a3700_pwr_domain_off,
+	.pwr_domain_suspend = a3700_pwr_domain_suspend,
+	.pwr_domain_on_finish = a3700_pwr_domain_on_finish,
+	.pwr_domain_suspend_finish = a3700_pwr_domain_suspend_finish,
+	.get_sys_suspend_power_state = a3700_get_sys_suspend_power_state,
+	.system_off = a3700_system_off,
+	.system_reset = a3700_system_reset,
+	.validate_power_state = a3700_validate_power_state,
+	.validate_ns_entrypoint = a3700_validate_ns_entrypoint
+};
diff --git a/plat/marvell/armada/a8k/a70x0/board/dram_port.c b/plat/marvell/armada/a8k/a70x0/board/dram_port.c
new file mode 100644
index 0000000..355770b
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0/board/dram_port.c
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+
+#include <mv_ddr_if.h>
+#include <plat_marvell.h>
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+}
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+/* FIXME: MISL board 2CS 4Gb x8 devices of micron - 2133P */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2133P,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_4GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	MV_DDR_32BIT_ECC_PUP8_BUS_MASK,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
diff --git a/plat/marvell/armada/a8k/a70x0/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a70x0/board/marvell_plat_config.c
new file mode 100644
index 0000000..a409261
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0/board/marvell_plat_config.c
@@ -0,0 +1,151 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP0 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win,
+			       uint32_t *size, uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO_WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+#ifndef IMAGE_BLE
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000, MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000, MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map[] = {
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	{0x00000000c0000000,	0x30000000,	PEX2_TID},
+	{0x0000000800000000,	0x100000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = iob_memory_map;
+	*size = ARRAY_SIZE(iob_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {	/* IO window */
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,	IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+	/* This entry is prepared for OP-TEE OS that enables the LLC SRAM
+	 * and changes the window target to SRAM_TID.
+	 */
+	{PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, DRAM_0_TID},
+#endif
+	{0x00000000f2000000,	0xe000000,	IO_0_TID},
+	{0x00000000c0000000,	0x30000000,	IO_0_TID}, /* IO window */
+	{0x0000000800000000,	0x100000000,	IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifdef IMAGE_BLE
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+struct skip_image skip_im = {
+	.detection_method = GPIO,
+	.info.gpio.num = 33,
+	.info.gpio.button_state = HIGH,
+	.info.test.cp_ap = CP,
+	.info.test.cp_index = 0,
+};
+
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* Return the skip_image configurations */
+	return &skip_im;
+}
+#endif
+#endif
diff --git a/plat/marvell/armada/a8k/a70x0/mvebu_def.h b/plat/marvell/armada/a8k/a70x0/mvebu_def.h
new file mode 100644
index 0000000..72bca12
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0/mvebu_def.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		1	/* A70x0 has single CP0 */
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a70x0/platform.mk b/plat/marvell/armada/a8k/a70x0/platform.mk
new file mode 100644
index 0000000..39eb712
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+CP_NUM			:= 1
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_7K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR		:= $(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a8k/a70x0_amc/board/dram_port.c b/plat/marvell/armada/a8k/a70x0_amc/board/dram_port.c
new file mode 100644
index 0000000..9c8c97e
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_amc/board/dram_port.c
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+
+#include <mv_ddr_if.h>
+#include <plat_marvell.h>
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+}
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+/* FIXME: MISL board 2CS 8Gb x8 devices of micron - 2133P */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	MV_DDR_32BIT_ECC_PUP8_BUS_MASK,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
diff --git a/plat/marvell/armada/a8k/a70x0_amc/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a70x0_amc/board/marvell_plat_config.c
new file mode 100644
index 0000000..3b68e91
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_amc/board/marvell_plat_config.c
@@ -0,0 +1,148 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win *amb_memory_map;
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+#ifndef IMAGE_BLE
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,	MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,	MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map[] = {
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x6000000,	PEX0_TID},
+	{0x00000000c0000000,    0x30000000,     PEX0_TID},
+	{0x0000000800000000,    0x200000000,    PEX0_TID},
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = iob_memory_map;
+	*size = ARRAY_SIZE(iob_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,	IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+	/* This entry is prepared for OP-TEE OS that enables the LLC SRAM
+	 * and changes the window target to SRAM_TID.
+	 */
+	{PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, DRAM_0_TID},
+#endif
+	{0x00000000f2000000,	0xe000000,	IO_0_TID},
+	{0x00000000c0000000,    0x30000000,	IO_0_TID}, /* IO window */
+	{0x0000000800000000,    0x200000000,	IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifdef IMAGE_BLE
+
+struct pci_hw_cfg *plat_get_pcie_hw_data(void)
+{
+	return NULL;
+}
+
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+struct skip_image skip_im = {
+	.detection_method = GPIO,
+	.info.gpio.num = 33,
+	.info.gpio.button_state = HIGH,
+	.info.test.cp_ap = CP,
+	.info.test.cp_index = 0,
+};
+
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* Return the skip_image configurations */
+	return &skip_im;
+}
+#endif
+#endif
diff --git a/plat/marvell/armada/a8k/a70x0_amc/mvebu_def.h b/plat/marvell/armada/a8k/a70x0_amc/mvebu_def.h
new file mode 100644
index 0000000..cedf323
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_amc/mvebu_def.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		1	/* A70x0 has single CP0 */
+
+/***********************************************************************
+ * Required platform porting definitions common to all
+ * Management Compute SubSystems (MSS)
+ ***********************************************************************
+ */
+/*
+ * Load address of SCP_BL2
+ * SCP_BL2 is loaded to the same place as BL31.
+ * Once SCP_BL2 is transferred to the SCP,
+ * it is discarded and BL31 is loaded over the top.
+ */
+#ifdef SCP_IMAGE
+#define SCP_BL2_BASE		BL31_BASE
+#endif
+
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a70x0_amc/platform.mk b/plat/marvell/armada/a8k/a70x0_amc/platform.mk
new file mode 100644
index 0000000..39eb712
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_amc/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+CP_NUM			:= 1
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_7K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR		:= $(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a8k/a70x0_mochabin/board/dram_port.c b/plat/marvell/armada/a8k/a70x0_mochabin/board/dram_port.c
new file mode 100644
index 0000000..68d335b
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_mochabin/board/dram_port.c
@@ -0,0 +1,227 @@
+/*
+ * Copyright (C) 2021 Sartura Ltd.
+ * Copyright (C) 2021 Globalscale technologies, Inc.
+ * Copyright (C) 2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+
+#include <mv_ddr_if.h>
+#include <plat_marvell.h>
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+}
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+#if DDR_TOPOLOGY == 0
+static struct mv_ddr_topology_map board_topology_map_2g = {
+/* 1CS 4Gb x4 devices of Samsung K4A4G085WF */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2400R,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_4GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	BUS_MASK_32BIT,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+#endif
+
+#if DDR_TOPOLOGY == 1
+static struct mv_ddr_topology_map board_topology_map_4g = {
+/* 1CS 8Gb x4 devices of Samsung K4A8G085WC-BCTD */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0},
+	      {0x1, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2400R,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	BUS_MASK_32BIT,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+#endif
+
+#if DDR_TOPOLOGY == 2
+static struct mv_ddr_topology_map board_topology_map_8g = {
+/* 2CS 8Gb x8 devices of Micron MT40A1G8WE-083E IT */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2400R,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	BUS_MASK_32BIT,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+#endif
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+/* a70x0_mochabin board supports 3 DDR4 models (2G/1CS, 4G/1CS, 8G/2CS) */
+#if DDR_TOPOLOGY == 0
+	return &board_topology_map_2g;
+#elif DDR_TOPOLOGY == 1
+	return &board_topology_map_4g;
+#elif DDR_TOPOLOGY == 2
+	return &board_topology_map_8g;
+#else
+	#error "Unknown DDR topology"
+#endif
+}
diff --git a/plat/marvell/armada/a8k/a70x0_mochabin/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a70x0_mochabin/board/marvell_plat_config.c
new file mode 100644
index 0000000..1ed6323
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_mochabin/board/marvell_plat_config.c
@@ -0,0 +1,145 @@
+/*
+ * Copyright (C) 2021 Sartura Ltd.
+ * Copyright (C) 2021 Globalscale technologies, Inc.
+ * Copyright (C) 2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP0 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win,
+			       uint32_t *size, uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO_WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+#ifndef IMAGE_BLE
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000, MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000, MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map[] = {
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	{0x00000000c0000000,	0x30000000,	PEX2_TID},
+	{0x0000000800000000,	0x100000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = iob_memory_map;
+	*size = ARRAY_SIZE(iob_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {	/* IO window */
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,	IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+	/* This entry is prepared for OP-TEE OS that enables the LLC SRAM
+	 * and changes the window target to SRAM_TID.
+	 */
+	{PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, DRAM_0_TID},
+#endif
+	{0x00000000f2000000,	0xe000000,	IO_0_TID},
+	{0x00000000c0000000,	0x30000000,	IO_0_TID}, /* IO window */
+	{0x0000000800000000,	0x100000000,	IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifdef IMAGE_BLE
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* No recovery button on a70x0_mochabin board */
+	return NULL;
+}
+#endif
+#endif
diff --git a/plat/marvell/armada/a8k/a70x0_mochabin/board/phy-porting-layer.h b/plat/marvell/armada/a8k/a70x0_mochabin/board/phy-porting-layer.h
new file mode 100644
index 0000000..ab76c31
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_mochabin/board/phy-porting-layer.h
@@ -0,0 +1,87 @@
+/*
+ * Copyright (C) 2021 Sartura Ltd.
+ * Copyright (C) 2021 Globalscale technologies, Inc.
+ * Copyright (C) 2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef __PHY_PORTING_LAYER_H
+#define __PHY_PORTING_LAYER_H
+
+#define MAX_LANE_NR		6
+
+static const struct xfi_params
+	xfi_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	/* AP0 */
+	{
+		/* CP 0 */
+		{
+			{ 0 }, /* Comphy0 */
+			{ 0 }, /* Comphy1 */
+			{ 0 }, /* Comphy2 */
+			{ 0 }, /* Comphy3 */
+			{ .g1_ffe_res_sel = 0x3, .g1_ffe_cap_sel = 0xf, .align90 = 0x60,
+			  .g1_dfe_res = 0x1, .g1_amp = 0x1c, .g1_emph = 0xe,
+			  .g1_emph_en = 0x1, .g1_tx_amp_adj = 0x1, .g1_tx_emph_en = 0x1,
+			  .g1_tx_emph = 0x0, .g1_rx_selmuff = 0x1, .g1_rx_selmufi = 0x0,
+			  .g1_rx_selmupf = 0x2, .g1_rx_selmupi = 0x2,
+			  .valid = 1 }, /* Comphy4 */
+			{ 0 }, /* Comphy5 */
+		},
+	},
+};
+
+static const struct sata_params
+	sata_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	/* AP0 */
+	{
+		/* CP 0 */
+		{
+			{ 0 }, /* Comphy0 */
+			{ 0 }, /* Comphy1 */
+			{ .g1_amp = 0x8, .g2_amp = 0xa, .g3_amp = 0x1e,
+			  .g1_emph = 0x1, .g2_emph = 0x2, .g3_emph = 0xe,
+			  .g1_emph_en = 0x1, .g2_emph_en = 0x1, .g3_emph_en = 0x1,
+			  .g1_tx_amp_adj = 0x1, .g2_tx_amp_adj = 0x1, .g3_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x0, .g2_tx_emph_en = 0x0, .g3_tx_emph_en = 0x0,
+			  .g1_tx_emph = 0x1, .g2_tx_emph = 0x1, .g3_tx_emph = 0x1,
+			  .g3_dfe_res = 0x1, .g3_ffe_res_sel = 0x4, .g3_ffe_cap_sel = 0xf,
+			  .align90 = 0x61,
+			  .g1_rx_selmuff = 0x3, .g2_rx_selmuff = 0x3, .g3_rx_selmuff = 0x3,
+			  .g1_rx_selmufi = 0x0, .g2_rx_selmufi = 0x0, .g3_rx_selmufi = 0x3,
+			  .g1_rx_selmupf = 0x1, .g2_rx_selmupf = 0x1, .g3_rx_selmupf = 0x2,
+			  .g1_rx_selmupi = 0x0, .g2_rx_selmupi = 0x0, .g3_rx_selmupi = 0x2,
+			  .polarity_invert = COMPHY_POLARITY_NO_INVERT,
+			  .valid = 0x1
+			}, /* Comphy2 */
+			{ .g1_amp = 0x8, .g2_amp = 0xa, .g3_amp = 0x1e,
+			  .g1_emph = 0x1, .g2_emph = 0x2, .g3_emph = 0xe,
+			  .g1_emph_en = 0x1, .g2_emph_en = 0x1, .g3_emph_en = 0x1,
+			  .g1_tx_amp_adj = 0x1, .g2_tx_amp_adj = 0x1, .g3_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x0, .g2_tx_emph_en = 0x0, .g3_tx_emph_en = 0x0,
+			  .g1_tx_emph = 0x1, .g2_tx_emph = 0x1, .g3_tx_emph = 0x1,
+			  .g3_dfe_res = 0x1, .g3_ffe_res_sel = 0x4, .g3_ffe_cap_sel = 0xf,
+			  .align90 = 0x61,
+			  .g1_rx_selmuff = 0x3, .g2_rx_selmuff = 0x3, .g3_rx_selmuff = 0x3,
+			  .g1_rx_selmufi = 0x0, .g2_rx_selmufi = 0x0, .g3_rx_selmufi = 0x3,
+			  .g1_rx_selmupf = 0x1, .g2_rx_selmupf = 0x1, .g3_rx_selmupf = 0x2,
+			  .g1_rx_selmupi = 0x0, .g2_rx_selmupi = 0x0, .g3_rx_selmupi = 0x2,
+			  .polarity_invert = COMPHY_POLARITY_NO_INVERT,
+			  .valid = 0x1
+			}, /* Comphy3 */
+			{ 0 }, /* Comphy4 */
+			{ 0 }, /* Comphy5 */
+		},
+	},
+};
+
+static const struct usb_params
+	usb_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	[0 ... AP_NUM-1][0 ... CP_NUM-1][0 ... MAX_LANE_NR-1] = {
+		.polarity_invert = COMPHY_POLARITY_NO_INVERT
+	},
+};
+
+#endif /* __PHY_PORTING_LAYER_H */
diff --git a/plat/marvell/armada/a8k/a70x0_mochabin/mvebu_def.h b/plat/marvell/armada/a8k/a70x0_mochabin/mvebu_def.h
new file mode 100644
index 0000000..768f735
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_mochabin/mvebu_def.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright (C) 2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		1	/* A70x0 has single CP0 */
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a70x0_mochabin/platform.mk b/plat/marvell/armada/a8k/a70x0_mochabin/platform.mk
new file mode 100644
index 0000000..2495591
--- /dev/null
+++ b/plat/marvell/armada/a8k/a70x0_mochabin/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2021 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+CP_NUM			:= 1
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_7K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR		:= $(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a8k/a80x0/board/dram_port.c b/plat/marvell/armada/a8k/a80x0/board/dram_port.c
new file mode 100644
index 0000000..47bc0a8
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0/board/dram_port.c
@@ -0,0 +1,147 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/mentor/mi2cv.h>
+#include <lib/mmio.h>
+
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_AP_MPP_CTRL0_7_REG		MVEBU_AP_MPP_REGS(0)
+#define MVEBU_AP_MPP_CTRL4_OFFS			16
+#define MVEBU_AP_MPP_CTRL5_OFFS			20
+#define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA		0x3
+#define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA		0x3
+
+#define MVEBU_CP_MPP_CTRL37_OFFS		20
+#define MVEBU_CP_MPP_CTRL38_OFFS		24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA	0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA	0x2
+
+#define MVEBU_MPP_CTRL_MASK			0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	/* MISL board with 1CS 8Gb x4 devices of Micron 2400T */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x0, 0, 0},	/* FIXME: change the cs mask for all 64 bit */
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0} },
+	   /* TODO: double check if the speed bin is 2400T */
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+#if DDR32
+	MV_DDR_32BIT_ECC_PUP8_BUS_MASK, /* subphys mask */
+#else
+	MV_DDR_64BIT_ECC_PUP8_BUS_MASK, /* subphys mask */
+#endif
+	MV_DDR_CFG_SPD,			/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+	uintptr_t reg;
+	uint32_t val;
+
+	reg = MVEBU_CP_MPP_REGS(0, 4);
+	/* configure CP0 MPP 37 and 38 to i2c */
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
+	val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA <<
+			MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA <<
+			MVEBU_CP_MPP_CTRL38_OFFS);
+	mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	INFO("Gathering DRAM information\n");
+
+	if (tm->cfg_src == MV_DDR_CFG_SPD) {
+		/* configure MPPs to enable i2c */
+		mpp_config();
+
+		/* initialize i2c */
+		i2c_init((void *)MVEBU_CP0_I2C_BASE);
+
+		/* select SPD memory page 0 to access DRAM configuration */
+		i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 0);
+
+		/* read data from spd */
+		i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+			 sizeof(tm->spd_data.all_bytes));
+	}
+}
diff --git a/plat/marvell/armada/a8k/a80x0/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a80x0/board/marvell_plat_config.c
new file mode 100644
index 0000000..4ccda14
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0/board/marvell_plat_config.c
@@ -0,0 +1,202 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP1 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+	/* CP1 (MCI0) internal regs */
+	{0x00000000f4000000,		0x2000000,  MCI_0_TID},
+#ifndef IMAGE_BLE
+	/* PCIe0 and SPI1_CS0 (RUNIT) on CP1*/
+	{0x00000000f9000000,		0x2000000,  MCI_0_TID},
+	/* PCIe1 on CP1*/
+	{0x00000000fb000000,		0x1000000,  MCI_0_TID},
+	/* PCIe2 on CP1*/
+	{0x00000000fc000000,		0x1000000,  MCI_0_TID},
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,  MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,  MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map_cp0[] = {
+	/* CP0 */
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	{0x00000000c0000000,	0x30000000,	PEX0_TID},
+	{0x0000000800000000,	0x100000000,	PEX0_TID},
+};
+
+struct addr_map_win iob_memory_map_cp1[] = {
+	/* CP1 */
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+	/* PEX1_X1 window */
+	{0x00000000fb000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000fc000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000fa000000,	0x1000000,	PEX0_TID}
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	switch (base) {
+	case MVEBU_CP_REGS_BASE(0):
+		*win = iob_memory_map_cp0;
+		*size = ARRAY_SIZE(iob_memory_map_cp0);
+		return 0;
+	case MVEBU_CP_REGS_BASE(1):
+		*win = iob_memory_map_cp1;
+		*size = ARRAY_SIZE(iob_memory_map_cp1);
+		return 0;
+	default:
+		*size = 0;
+		*win = 0;
+		return 1;
+	}
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,  IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+	/* This entry is prepared for OP-TEE OS that enables the LLC SRAM
+	 * and changes the window target to SRAM_TID.
+	 */
+	{PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, DRAM_0_TID},
+#endif
+	{0x00000000f2000000,	0xe000000,  IO_0_TID}, /* IO window */
+	{0x00000000c0000000,	0x30000000,  IO_0_TID}, /* IO window */
+	{0x0000000800000000,	0x100000000,  IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * SoC PM configuration
+ *****************************************************************************
+ */
+/* CP GPIO should be used and the GPIOs should be within same GPIO register */
+struct power_off_method pm_cfg = {
+	.type = PMIC_GPIO,
+	.cfg.gpio.pin_count = 1,
+	.cfg.gpio.info = {{0, 35} },
+	.cfg.gpio.step_count = 7,
+	.cfg.gpio.seq = {1, 0, 1, 0, 1, 0, 1},
+	.cfg.gpio.delay_ms = 10,
+};
+
+void *plat_marvell_get_pm_cfg(void)
+{
+	/* Return the PM configurations */
+	return &pm_cfg;
+}
+
+/* In reference to #ifndef IMAGE_BLE, this part is used for BLE only. */
+#else
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+struct skip_image skip_im = {
+	.detection_method = GPIO,
+	.info.gpio.num = 33,
+	.info.gpio.button_state = HIGH,
+	.info.test.cp_ap = CP,
+	.info.test.cp_index = 0,
+};
+
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* Return the skip_image configurations */
+	return &skip_im;
+}
+#endif
+#endif
diff --git a/plat/marvell/armada/a8k/a80x0/board/phy-porting-layer.h b/plat/marvell/armada/a8k/a80x0/board/phy-porting-layer.h
new file mode 100644
index 0000000..afa3be1
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0/board/phy-porting-layer.h
@@ -0,0 +1,192 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef PHY_PORTING_LAYER_H
+#define PHY_PORTING_LAYER_H
+
+#define MAX_LANE_NR		6
+
+static const struct xfi_params
+	xfi_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	/* AP0 */
+	{
+		/* CP 0 */
+		{
+			{ 0 }, /* Comphy0 */
+			{ 0 }, /* Comphy1 */
+			{ .g1_ffe_res_sel = 0x3, .g1_ffe_cap_sel = 0xf,
+			  .align90 = 0x5f,
+			  .g1_dfe_res = 0x2, .g1_amp = 0x1c, .g1_emph = 0xe,
+			  .g1_emph_en = 0x1, .g1_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x1, .g1_tx_emph = 0x0,
+			  .g1_rx_selmuff = 0x1, .g1_rx_selmufi = 0x0,
+			  .g1_rx_selmupf = 0x2, .g1_rx_selmupi = 0x2,
+			  .valid = 0x1 }, /* Comphy2 */
+			{ 0 }, /* Comphy3 */
+			{ .g1_ffe_res_sel = 0x3, .g1_ffe_cap_sel = 0xf,
+			  .align90 = 0x5f,
+			  .g1_dfe_res = 0x2, .g1_amp = 0x1c, .g1_emph = 0xe,
+			  .g1_emph_en = 0x1, .g1_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x1, .g1_tx_emph = 0x0,
+			  .g1_rx_selmuff = 0x1, .g1_rx_selmufi = 0x0,
+			  .g1_rx_selmupf = 0x2, .g1_rx_selmupi = 0x2,
+			  .valid = 0x1 }, /* Comphy4 */
+			{ 0 }, /* Comphy5 */
+		},
+
+		/* CP 1 */
+		{
+			{ 0 }, /* Comphy0 */
+			{ 0 }, /* Comphy1 */
+			{ .g1_ffe_res_sel = 0x3, .g1_ffe_cap_sel = 0xf,
+			  .align90 = 0x5f,
+			  .g1_dfe_res = 0x2, .g1_amp = 0x1c, .g1_emph = 0xe,
+			  .g1_emph_en = 0x1, .g1_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x1, .g1_tx_emph = 0x0,
+			  .g1_rx_selmuff = 0x1, .g1_rx_selmufi = 0x0,
+			  .g1_rx_selmupf = 0x2, .g1_rx_selmupi = 0x2,
+			  .valid = 0x1 }, /* Comphy2 */
+			{ 0 }, /* Comphy3 */
+			{ .g1_ffe_res_sel = 0x3, .g1_ffe_cap_sel = 0xf,
+			  .align90 = 0x5f,
+			  .g1_dfe_res = 0x2, .g1_amp = 0x1c, .g1_emph = 0xe,
+			  .g1_emph_en = 0x1, .g1_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x1, .g1_tx_emph = 0x0,
+			  .g1_rx_selmuff = 0x1, .g1_rx_selmufi = 0x0,
+			  .g1_rx_selmupf = 0x2, .g1_rx_selmupi = 0x2,
+			  .valid = 0x1 }, /* Comphy4 */
+			{ 0 }, /* Comphy5 */
+		},
+	},
+};
+
+static const struct sata_params
+	sata_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	/* AP0 */
+	{
+		/* CP 0 */
+		{
+			{ 0 }, /* Comphy0 */
+			{ .g1_amp = 0x8, .g2_amp = 0xa, .g3_amp = 0x1e,
+			  .g1_emph = 0x1, .g2_emph = 0x2, .g3_emph = 0xe,
+			  .g1_emph_en = 0x1, .g2_emph_en = 0x1,
+			  .g3_emph_en = 0x1,
+			  .g1_tx_amp_adj = 0x1, .g2_tx_amp_adj = 0x1,
+			  .g3_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x0, .g2_tx_emph_en = 0x0,
+			  .g3_tx_emph_en = 0x0,
+			  .g1_tx_emph = 0x1, .g2_tx_emph = 0x1,
+			  .g3_tx_emph = 0x1,
+			  .g3_dfe_res = 0x1, .g3_ffe_res_sel = 0x4,
+			  .g3_ffe_cap_sel = 0xf,
+			  .align90 = 0x61,
+			  .g1_rx_selmuff = 0x3, .g2_rx_selmuff = 0x3,
+			  .g3_rx_selmuff = 0x3,
+			  .g1_rx_selmufi = 0x0, .g2_rx_selmufi = 0x0,
+			  .g3_rx_selmufi = 0x3,
+			  .g1_rx_selmupf = 0x1, .g2_rx_selmupf = 0x1,
+			  .g3_rx_selmupf = 0x2,
+			  .g1_rx_selmupi = 0x0, .g2_rx_selmupi = 0x0,
+			  .g3_rx_selmupi = 0x2,
+			  .polarity_invert = COMPHY_POLARITY_NO_INVERT,
+			  .valid = 0x1
+			}, /* Comphy1 */
+			{ 0 }, /* Comphy2 */
+			{ .g1_amp = 0x8, .g2_amp = 0xa, .g3_amp = 0x1e,
+			 .g1_emph = 0x1, .g2_emph = 0x2, .g3_emph = 0xe,
+			 .g1_emph_en = 0x1, .g2_emph_en = 0x1,
+			 .g3_emph_en = 0x1,
+			 .g1_tx_amp_adj = 0x1, .g2_tx_amp_adj = 0x1,
+			 .g3_tx_amp_adj = 0x1,
+			 .g1_tx_emph_en = 0x0, .g2_tx_emph_en = 0x0,
+			 .g3_tx_emph_en = 0x0,
+			 .g1_tx_emph = 0x1, .g2_tx_emph = 0x1,
+			 .g3_tx_emph = 0x1,
+			 .g3_dfe_res = 0x1, .g3_ffe_res_sel = 0x4,
+			 .g3_ffe_cap_sel = 0xf,
+			 .align90 = 0x61,
+			 .g1_rx_selmuff = 0x3, .g2_rx_selmuff = 0x3,
+			 .g3_rx_selmuff = 0x3,
+			 .g1_rx_selmufi = 0x0, .g2_rx_selmufi = 0x0,
+			 .g3_rx_selmufi = 0x3,
+			 .g1_rx_selmupf = 0x1, .g2_rx_selmupf = 0x1,
+			 .g3_rx_selmupf = 0x2,
+			 .g1_rx_selmupi = 0x0, .g2_rx_selmupi = 0x0,
+			 .g3_rx_selmupi = 0x2,
+			 .polarity_invert = COMPHY_POLARITY_NO_INVERT,
+			 .valid = 0x1
+			}, /* Comphy3 */
+			{ 0 }, /* Comphy4 */
+			{ 0 }, /* Comphy5 */
+		},
+
+		/* CP 1 */
+		{
+			{ 0 }, /* Comphy0 */
+			{ .g1_amp = 0x8, .g2_amp = 0xa, .g3_amp = 0x1e,
+			  .g1_emph = 0x1, .g2_emph = 0x2, .g3_emph = 0xe,
+			  .g1_emph_en = 0x1, .g2_emph_en = 0x1,
+			  .g3_emph_en = 0x1,
+			  .g1_tx_amp_adj = 0x1, .g2_tx_amp_adj = 0x1,
+			  .g3_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x0, .g2_tx_emph_en = 0x0,
+			  .g3_tx_emph_en = 0x0,
+			  .g1_tx_emph = 0x1, .g2_tx_emph = 0x1,
+			  .g3_tx_emph = 0x1,
+			  .g3_dfe_res = 0x1, .g3_ffe_res_sel = 0x4,
+			  .g3_ffe_cap_sel = 0xf,
+			  .align90 = 0x61,
+			  .g1_rx_selmuff = 0x3, .g2_rx_selmuff = 0x3,
+			  .g3_rx_selmuff = 0x3,
+			  .g1_rx_selmufi = 0x0, .g2_rx_selmufi = 0x0,
+			  .g3_rx_selmufi = 0x3,
+			  .g1_rx_selmupf = 0x1, .g2_rx_selmupf = 0x1,
+			  .g3_rx_selmupf = 0x2,
+			  .g1_rx_selmupi = 0x0, .g2_rx_selmupi = 0x0,
+			  .g3_rx_selmupi = 0x2,
+			  .polarity_invert = COMPHY_POLARITY_NO_INVERT,
+			  .valid = 0x1
+			}, /* Comphy1 */
+			{ 0 }, /* Comphy2 */
+			{ .g1_amp = 0x8, .g2_amp = 0xa, .g3_amp = 0x1e,
+			  .g1_emph = 0x1, .g2_emph = 0x2, .g3_emph = 0xe,
+			  .g1_emph_en = 0x1, .g2_emph_en = 0x1,
+			  .g3_emph_en = 0x1,
+			  .g1_tx_amp_adj = 0x1, .g2_tx_amp_adj = 0x1,
+			  .g3_tx_amp_adj = 0x1,
+			  .g1_tx_emph_en = 0x0, .g2_tx_emph_en = 0x0,
+			  .g3_tx_emph_en = 0x0,
+			  .g1_tx_emph = 0x1, .g2_tx_emph = 0x1,
+			  .g3_tx_emph = 0x1,
+			  .g3_dfe_res = 0x1, .g3_ffe_res_sel = 0x4,
+			  .g3_ffe_cap_sel = 0xf,
+			  .align90 = 0x61,
+			  .g1_rx_selmuff = 0x3, .g2_rx_selmuff = 0x3,
+			  .g3_rx_selmuff = 0x3,
+			  .g1_rx_selmufi = 0x0, .g2_rx_selmufi = 0x0,
+			  .g3_rx_selmufi = 0x3,
+			  .g1_rx_selmupf = 0x1, .g2_rx_selmupf = 0x1,
+			  .g3_rx_selmupf = 0x2,
+			  .g1_rx_selmupi = 0x0, .g2_rx_selmupi = 0x0,
+			  .g3_rx_selmupi = 0x2,
+			  .polarity_invert = COMPHY_POLARITY_NO_INVERT,
+			  .valid = 0x1
+			}, /* Comphy3 */
+			{ 0 }, /* Comphy4 */
+			{ 0 }, /* Comphy5 */
+
+		},
+	},
+};
+
+static const struct usb_params
+	usb_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	[0 ... AP_NUM-1][0 ... CP_NUM-1][0 ... MAX_LANE_NR-1] = {
+		.polarity_invert = COMPHY_POLARITY_NO_INVERT
+	},
+};
+#endif /* PHY_PORTING_LAYER_H */
diff --git a/plat/marvell/armada/a8k/a80x0/mvebu_def.h b/plat/marvell/armada/a8k/a80x0/mvebu_def.h
new file mode 100644
index 0000000..3fa119a
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0/mvebu_def.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		2	/* A80x0 has both CP0 & CP1 */
+#define I2C_SPD_ADDR		0x53	/* Access SPD data */
+#define I2C_SPD_P0_ADDR		0x36	/* Select SPD data page 0 */
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a80x0/platform.mk b/plat/marvell/armada/a8k/a80x0/platform.mk
new file mode 100644
index 0000000..115dd4a
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+CP_NUM			:= 2
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_8K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR		:= $(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a8k/a80x0_mcbin/board/dram_port.c b/plat/marvell/armada/a8k/a80x0_mcbin/board/dram_port.c
new file mode 100644
index 0000000..85c931c
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_mcbin/board/dram_port.c
@@ -0,0 +1,131 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/mentor/mi2cv.h>
+#include <lib/mmio.h>
+
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_CP_MPP_CTRL37_OFFS		20
+#define MVEBU_CP_MPP_CTRL38_OFFS		24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA	0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA	0x2
+
+#define MVEBU_MPP_CTRL_MASK			0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	/* Board with 1CS 8Gb x4 devices of Micron 2400T */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x0, 0, 0},	/* FIXME: change the cs mask for all 64 bit */
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0} },
+	   /* TODO: double check if the speed bin is 2400T */
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	   MV_DDR_64BIT_BUS_MASK,	/* subphys mask */
+	   MV_DDR_CFG_SPD,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+	uint32_t val;
+	uintptr_t reg = MVEBU_CP_MPP_REGS(0, 4);
+
+	/* configure CP0 MPP 37 and 38 to i2c */
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
+	val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA << MVEBU_CP_MPP_CTRL38_OFFS);
+	mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	INFO("Gathering DRAM information\n");
+
+	if (tm->cfg_src == MV_DDR_CFG_SPD) {
+		/* configure MPPs to enable i2c */
+		mpp_config();
+		/* initialize the i2c */
+		i2c_init((void *)MVEBU_CP0_I2C_BASE);
+		/* select SPD memory page 0 to access DRAM configuration */
+		i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 0);
+		/* read data from spd */
+		i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+			 sizeof(tm->spd_data.all_bytes));
+	}
+}
diff --git a/plat/marvell/armada/a8k/a80x0_mcbin/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a80x0_mcbin/board/marvell_plat_config.c
new file mode 100644
index 0000000..75a1b0c
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_mcbin/board/marvell_plat_config.c
@@ -0,0 +1,200 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <drivers/delay_timer.h>
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * GPIO Configuration
+ *****************************************************************************
+ */
+#define MPP_CONTROL_REGISTER		0xf2440018
+#define MPP_CONTROL_MPP_SEL_52_MASK	0xf0000
+#define GPIO_DATA_OUT1_REGISTER		0xf2440140
+#define GPIO_DATA_OUT_EN_CTRL1_REGISTER 0xf2440144
+#define GPIO52_MASK			0x100000
+
+/* Reset PCIe via GPIO number 52 */
+int marvell_gpio_config(void)
+{
+	uint32_t reg;
+
+	reg = mmio_read_32(MPP_CONTROL_REGISTER);
+	reg |= MPP_CONTROL_MPP_SEL_52_MASK;
+	mmio_write_32(MPP_CONTROL_REGISTER, reg);
+
+	reg = mmio_read_32(GPIO_DATA_OUT1_REGISTER);
+	reg |= GPIO52_MASK;
+	mmio_write_32(GPIO_DATA_OUT1_REGISTER, reg);
+
+	reg = mmio_read_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER);
+	reg &= ~GPIO52_MASK;
+	mmio_write_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER, reg);
+	udelay(100);
+
+	return 0;
+}
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP1 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+	/* CP1 (MCI0) internal regs */
+	{0x00000000f4000000,		0x2000000,  MCI_0_TID},
+#ifndef IMAGE_BLE
+	/* PCIe0-2 and SPI1_CS0 (RUNIT) on CP1*/
+	{0x00000000f9000000,		0x4000000,  MCI_0_TID},
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,   MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,   MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map_cp0[] = {
+	/* CP0 */
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	{0x00000000c0000000,	0x30000000,	PEX0_TID},
+	{0x0000000800000000,	0x100000000,	PEX0_TID},
+};
+
+struct addr_map_win iob_memory_map_cp1[] = {
+	/* CP1 */
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+	/* PEX1_X1 window */
+	{0x00000000fb000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000fc000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000fa000000,	0x1000000,	PEX0_TID}
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	switch (base) {
+	case MVEBU_CP_REGS_BASE(0):
+		*win = iob_memory_map_cp0;
+		*size = ARRAY_SIZE(iob_memory_map_cp0);
+		return 0;
+	case MVEBU_CP_REGS_BASE(1):
+		*win = iob_memory_map_cp1;
+		*size = ARRAY_SIZE(iob_memory_map_cp1);
+		return 0;
+	default:
+		*size = 0;
+		*win = 0;
+		return 1;
+	}
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,  IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+	/* This entry is prepared for OP-TEE OS that enables the LLC SRAM
+	 * and changes the window target to SRAM_TID.
+	 */
+	{PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, DRAM_0_TID},
+#endif
+	{0x00000000f2000000,	0xe000000,  IO_0_TID}, /* IO window */
+	{0x00000000c0000000,	0x30000000,  IO_0_TID}, /* IO window */
+	{0x0000000800000000,	0x100000000,  IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+/* In reference to #ifndef IMAGE_BLE, this part is used for BLE only. */
+
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* No recovery button on A8k-MCBIN board */
+	return NULL;
+}
diff --git a/plat/marvell/armada/a8k/a80x0_mcbin/mvebu_def.h b/plat/marvell/armada/a8k/a80x0_mcbin/mvebu_def.h
new file mode 100644
index 0000000..3fa119a
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_mcbin/mvebu_def.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		2	/* A80x0 has both CP0 & CP1 */
+#define I2C_SPD_ADDR		0x53	/* Access SPD data */
+#define I2C_SPD_P0_ADDR		0x36	/* Select SPD data page 0 */
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a80x0_mcbin/platform.mk b/plat/marvell/armada/a8k/a80x0_mcbin/platform.mk
new file mode 100644
index 0000000..115dd4a
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_mcbin/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+CP_NUM			:= 2
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_8K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR		:= $(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/board/dram_port.c b/plat/marvell/armada/a8k/a80x0_puzzle/board/dram_port.c
new file mode 100644
index 0000000..1d8e9d2
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/board/dram_port.c
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/mentor/mi2cv.h>
+#include <lib/mmio.h>
+
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_AP_MPP_CTRL0_7_REG                MVEBU_AP_MPP_REGS(0)
+#define MVEBU_AP_MPP_CTRL4_OFFS                 16
+#define MVEBU_AP_MPP_CTRL5_OFFS                 20
+#define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA         0x3
+#define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA         0x3
+
+#define MVEBU_CP_MPP_CTRL37_OFFS		20
+#define MVEBU_CP_MPP_CTRL38_OFFS		24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA	0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA	0x2
+
+#define MVEBU_MPP_CTRL_MASK			0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	/* Board with 1CS 8Gb x4 devices of Micron 2400T */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x0, 0, 0},	/* FIXME: change the cs mask for all 64 bit */
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0} },
+	   /* TODO: double check if the speed bin is 2400T */
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	   MV_DDR_64BIT_BUS_MASK,	/* subphys mask */
+	   MV_DDR_CFG_SPD,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined*/
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+	uint32_t val;
+	uintptr_t reg;
+
+       /* configure ap mmps 4, 5 to I2C */
+	reg = MVEBU_AP_MPP_CTRL0_7_REG;
+
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_AP_MPP_CTRL4_OFFS) |
+		(MVEBU_MPP_CTRL_MASK << MVEBU_AP_MPP_CTRL5_OFFS));
+	val |= ((MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA << MVEBU_AP_MPP_CTRL4_OFFS) |
+		(MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA << MVEBU_AP_MPP_CTRL5_OFFS));
+
+	mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	INFO("Gathering DRAM information\n");
+
+	if (tm->cfg_src == MV_DDR_CFG_SPD) {
+		/* configure MPPs to enable i2c */
+		mpp_config();
+		/* initialize the MVEBU_AP_I2C_BASE I2C bus */
+		i2c_init((void *)MVEBU_AP_I2C_BASE);
+		/* select SPD memory page 0 to access DRAM configuration */
+		i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 0);
+		/* read data from spd */
+		i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+			 sizeof(tm->spd_data.all_bytes));
+	}
+}
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a80x0_puzzle/board/marvell_plat_config.c
new file mode 100644
index 0000000..0edc977
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/board/marvell_plat_config.c
@@ -0,0 +1,201 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <drivers/delay_timer.h>
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * GPIO Configuration
+ *****************************************************************************
+ */
+#define MPP_CONTROL_REGISTER		0xf2440018
+#define MPP_CONTROL_MPP_SEL_52_MASK	0xf0000
+#define GPIO_DATA_OUT1_REGISTER		0xf2440140
+#define GPIO_DATA_OUT_EN_CTRL1_REGISTER 0xf2440144
+#define GPIO52_MASK			0x100000
+
+/* Reset PCIe via GPIO number 52 */
+int marvell_gpio_config(void)
+{
+	uint32_t reg;
+
+	reg = mmio_read_32(MPP_CONTROL_REGISTER);
+	reg |= MPP_CONTROL_MPP_SEL_52_MASK;
+	mmio_write_32(MPP_CONTROL_REGISTER, reg);
+
+	reg = mmio_read_32(GPIO_DATA_OUT1_REGISTER);
+	reg |= GPIO52_MASK;
+	mmio_write_32(GPIO_DATA_OUT1_REGISTER, reg);
+
+	reg = mmio_read_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER);
+	reg &= ~GPIO52_MASK;
+	mmio_write_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER, reg);
+	udelay(100);
+
+	return 0;
+}
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP1 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+	/* CP1 (MCI0) internal regs */
+	{0x00000000f4000000,		0x2000000,  MCI_0_TID},
+#ifndef IMAGE_BLE
+	/* PCIe0 and SPI1_CS0 (RUNIT) on CP1*/
+	{0x00000000f9000000,		0x2000000,  MCI_0_TID},
+	/* PCIe1 on CP1*/
+	{0x00000000fb000000,		0x1000000,  MCI_0_TID},
+	/* PCIe2 on CP1*/
+	{0x00000000fc000000,		0x1000000,  MCI_0_TID},
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,   MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,   MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map_cp0[] = {
+	/* CP0 */
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	{0x00000000c0000000,	0x30000000,	PEX0_TID},
+	{0x0000000800000000,	0x100000000,	PEX0_TID},
+};
+
+struct addr_map_win iob_memory_map_cp1[] = {
+	/* CP1 */
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+	/* PEX1_X1 window */
+	{0x00000000fb000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000fc000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000fa000000,	0x1000000,	PEX0_TID}
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	switch (base) {
+	case MVEBU_CP_REGS_BASE(0):
+		*win = iob_memory_map_cp0;
+		*size = ARRAY_SIZE(iob_memory_map_cp0);
+		return 0;
+	case MVEBU_CP_REGS_BASE(1):
+		*win = iob_memory_map_cp1;
+		*size = ARRAY_SIZE(iob_memory_map_cp1);
+		return 0;
+	default:
+		*size = 0;
+		*win = 0;
+		return 1;
+	}
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,  IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+	{PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, SRAM_TID},
+#endif
+	{0x00000000f2000000,	0xe000000,  IO_0_TID}, /* IO window */
+	{0x00000000c0000000,	0x30000000,  IO_0_TID}, /* IO window */
+	{0x0000000800000000,	0x100000000,  IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+/* In reference to #ifndef IMAGE_BLE, this part is used for BLE only. */
+
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* No recovery button on A8k-MCBIN board */
+	return NULL;
+}
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/board/system_power.c b/plat/marvell/armada/a8k/a80x0_puzzle/board/system_power.c
new file mode 100644
index 0000000..eb00874
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/board/system_power.c
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <armada_common.h>
+#include <common/debug.h>
+#include <drivers/delay_timer.h>
+#include <drivers/ti/uart/uart_16550.h>
+#include <drivers/console.h>
+#include <plat_marvell.h>
+
+/*****************************************************************************
+ * Platform specific power off functions
+ * Power off PSU / Send command to power management MCU / ...
+ *****************************************************************************
+ */
+
+unsigned char add_xor_checksum(unsigned char *buf, unsigned char xor_len)
+{
+	unsigned char xor_sum = 0;
+	unsigned int i;
+
+	for (i = 0; i < xor_len; i++)
+		xor_sum ^= buf[i];
+
+	return xor_sum;
+}
+
+int system_power_off(void)
+{
+	static console_t console;
+
+	/* WT61P803 MCU system_off_now command */
+	unsigned char system_off_now[4] = { '@', 'C', '0' };
+	int i, len;
+
+	len = sizeof(system_off_now);
+	system_off_now[len - 1] = add_xor_checksum(system_off_now, len);
+
+	console_16550_register(PLAT_MARVELL_UART_BASE + 0x100,
+		PLAT_MARVELL_UART_CLK_IN_HZ, 115200, &console);
+
+	/* Send system_off_now to console */
+	for (i = 0; i < len; i++) {
+		console.putc(system_off_now[i],	&console);
+		udelay(1000);
+	}
+
+	console.flush(&console);
+	(void)console_unregister(&console);
+
+	mdelay(100);
+
+	return 0;
+}
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/mvebu_def.h b/plat/marvell/armada/a8k/a80x0_puzzle/mvebu_def.h
new file mode 100644
index 0000000..3fa119a
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/mvebu_def.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		2	/* A80x0 has both CP0 & CP1 */
+#define I2C_SPD_ADDR		0x53	/* Access SPD data */
+#define I2C_SPD_P0_ADDR		0x36	/* Select SPD data page 0 */
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/platform.mk b/plat/marvell/armada/a8k/a80x0_puzzle/platform.mk
new file mode 100644
index 0000000..3378d53
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+CP_NUM			:= 2
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_8K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR		:= 	$(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk
diff --git a/plat/marvell/armada/a8k/common/a8k_common.mk b/plat/marvell/armada/a8k/common/a8k_common.mk
new file mode 100644
index 0000000..4d8a87f
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/a8k_common.mk
@@ -0,0 +1,192 @@
+#
+# Copyright (C) 2016 - 2020 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+
+PLAT_FAMILY		:= a8k
+PLAT_INCLUDE_BASE	:= include/plat/marvell/armada/$(PLAT_FAMILY)
+PLAT_COMMON_BASE	:= plat/marvell/armada/a8k/common
+MARVELL_DRV_BASE	:= drivers/marvell
+MARVELL_COMMON_BASE	:= plat/marvell/armada/common
+
+MARVELL_SVC_TEST	:= 0
+$(eval $(call add_define,MARVELL_SVC_TEST))
+
+ERRATA_A72_859971	:= 1
+
+# Enable MSS support for a8k family
+MSS_SUPPORT		:= 1
+$(eval $(call add_define,MSS_SUPPORT))
+
+# Disable EL3 cache for power management
+BL31_CACHE_DISABLE	:= 0
+$(eval $(call add_define,BL31_CACHE_DISABLE))
+
+$(eval $(call add_define,PCI_EP_SUPPORT))
+$(eval $(call assert_boolean,PCI_EP_SUPPORT))
+
+AP_NUM			:= 1
+$(eval $(call add_define,AP_NUM))
+
+DOIMAGEPATH		?=	tools/marvell/doimage
+DOIMAGETOOL		?=	${DOIMAGEPATH}/doimage
+
+include plat/marvell/marvell.mk
+include tools/marvell/doimage/doimage.mk
+
+ifeq (${MARVELL_SECURE_BOOT},1)
+DOIMAGE_SEC_FLAGS := -c $(DOIMAGE_SEC)
+DOIMAGE_LIBS_CHECK = \
+        if ! [ -d "/usr/include/mbedtls" ]; then \
+                        echo "****************************************" >&2; \
+                        echo "Missing mbedTLS installation! " >&2; \
+                        echo "Please download it from \"tls.mbed.org\"" >&2; \
+			echo "Alternatively on Debian/Ubuntu system install" >&2; \
+			echo "\"libmbedtls-dev\" package" >&2; \
+                        echo "Make sure to use version 2.1.0 or later" >&2; \
+                        echo "****************************************" >&2; \
+                exit 1; \
+        else if ! [ -f "/usr/include/libconfig.h" ]; then \
+                        echo "********************************************************" >&2; \
+                        echo "Missing Libconfig installation!" >&2; \
+                        echo "Please download it from \"www.hyperrealm.com/libconfig/\"" >&2; \
+                        echo "Alternatively on Debian/Ubuntu system install packages" >&2; \
+                        echo "\"libconfig8\" and \"libconfig8-dev\"" >&2; \
+                        echo "********************************************************" >&2; \
+                exit 1; \
+        fi \
+        fi
+else #MARVELL_SECURE_BOOT
+DOIMAGE_LIBS_CHECK =
+DOIMAGE_SEC_FLAGS =
+endif #MARVELL_SECURE_BOOT
+
+ROM_BIN_EXT ?= $(BUILD_PLAT)/ble.bin
+DOIMAGE_FLAGS	+= -b $(ROM_BIN_EXT) $(NAND_DOIMAGE_FLAGS) $(DOIMAGE_SEC_FLAGS)
+
+# Check whether to build system_power.c for the platform
+ifneq ("$(wildcard $(BOARD_DIR)/board/system_power.c)","")
+SYSTEM_POWER_SUPPORT = 1
+else
+SYSTEM_POWER_SUPPORT = 0
+endif
+
+# This define specifies DDR type for BLE
+$(eval $(call add_define,CONFIG_DDR4))
+
+# This define specifies DDR topology for BLE
+DDR_TOPOLOGY	?= 0
+$(eval $(call add_define,DDR_TOPOLOGY))
+
+MARVELL_GIC_SOURCES	:=	drivers/arm/gic/common/gic_common.c	\
+				drivers/arm/gic/v2/gicv2_main.c		\
+				drivers/arm/gic/v2/gicv2_helpers.c	\
+				plat/common/plat_gicv2.c
+
+PLAT_INCLUDES		+=	-I$(BOARD_DIR)				\
+				-I$(BOARD_DIR)/board			\
+				-I$(CURDIR)/drivers/marvell		\
+				-I$(PLAT_COMMON_BASE)/include		\
+				-I$(PLAT_INCLUDE_BASE)/common
+
+PLAT_BL_COMMON_SOURCES	:=	$(PLAT_COMMON_BASE)/aarch64/a8k_common.c \
+				drivers/ti/uart/aarch64/16550_console.S
+
+ifndef BLE_PORTING_SOURCES
+BLE_PORTING_SOURCES	:=	$(BOARD_DIR)/board/dram_port.c \
+				$(BOARD_DIR)/board/marvell_plat_config.c
+endif
+
+MARVELL_MOCHI_DRV	+=	$(MARVELL_DRV_BASE)/mochi/cp110_setup.c
+
+BLE_SOURCES		:=	drivers/mentor/i2c/mi2cv.c		\
+				$(PLAT_COMMON_BASE)/plat_ble_setup.c	\
+				$(MARVELL_MOCHI_DRV)			\
+				$(PLAT_COMMON_BASE)/plat_pm.c		\
+				$(MARVELL_DRV_BASE)/ap807_clocks_init.c	\
+				$(MARVELL_DRV_BASE)/thermal.c		\
+				$(PLAT_COMMON_BASE)/plat_thermal.c	\
+				$(BLE_PORTING_SOURCES)			\
+				$(MARVELL_DRV_BASE)/ccu.c		\
+				$(MARVELL_DRV_BASE)/io_win.c
+
+BL1_SOURCES		+=	$(PLAT_COMMON_BASE)/aarch64/plat_helpers.S \
+				lib/cpus/aarch64/cortex_a72.S
+
+MARVELL_DRV		:= 	$(MARVELL_DRV_BASE)/io_win.c	\
+				$(MARVELL_DRV_BASE)/iob.c	\
+				$(MARVELL_DRV_BASE)/mci.c	\
+				$(MARVELL_DRV_BASE)/amb_adec.c	\
+				$(MARVELL_DRV_BASE)/ccu.c	\
+				$(MARVELL_DRV_BASE)/cache_llc.c	\
+				$(MARVELL_DRV_BASE)/comphy/phy-comphy-cp110.c	\
+				$(MARVELL_DRV_BASE)/mc_trustzone/mc_trustzone.c	\
+				$(MARVELL_DRV_BASE)/secure_dfx_access/armada_thermal.c	\
+				$(MARVELL_DRV_BASE)/secure_dfx_access/misc_dfx.c	\
+				$(MARVELL_DRV_BASE)/ddr_phy_access.c	\
+				drivers/rambus/trng_ip_76.c
+
+ifeq (${MSS_SUPPORT}, 1)
+MARVELL_DRV		+=	$(MARVELL_DRV_BASE)/mg_conf_cm3/mg_conf_cm3.c
+endif
+
+ifndef BL31_PORTING_SOURCES
+BL31_PORTING_SOURCES	:=	$(BOARD_DIR)/board/marvell_plat_config.c
+endif
+
+ifeq ($(SYSTEM_POWER_SUPPORT),1)
+BL31_PORTING_SOURCES	+=	$(BOARD_DIR)/board/system_power.c
+endif
+
+BL31_SOURCES		+=	lib/cpus/aarch64/cortex_a72.S		       \
+				$(PLAT_COMMON_BASE)/aarch64/plat_helpers.S     \
+				$(PLAT_COMMON_BASE)/aarch64/plat_arch_config.c \
+				$(PLAT_COMMON_BASE)/plat_pm.c		       \
+				$(PLAT_COMMON_BASE)/plat_bl31_setup.c	       \
+				$(MARVELL_COMMON_BASE)/marvell_gicv2.c	       \
+				$(MARVELL_COMMON_BASE)/mrvl_sip_svc.c	       \
+				$(MARVELL_COMMON_BASE)/marvell_ddr_info.c      \
+				$(BL31_PORTING_SOURCES)			       \
+				$(MARVELL_DRV)				       \
+				$(MARVELL_MOCHI_DRV)			       \
+				$(MARVELL_GIC_SOURCES)
+
+# Add trace functionality for PM
+BL31_SOURCES		+=	$(PLAT_COMMON_BASE)/plat_pm_trace.c
+
+
+ifeq (${MSS_SUPPORT}, 1)
+# Force builds with BL2 image on a80x0 platforms
+ifndef SCP_BL2
+ $(error "Error: SCP_BL2 image is mandatory for a8k family")
+endif
+
+# MSS (SCP) build
+include $(PLAT_COMMON_BASE)/mss/mss_a8k.mk
+endif
+
+# BLE (ROM context execution code, AKA binary extension)
+BLE_PATH	?=  $(PLAT_COMMON_BASE)/ble
+
+include ${BLE_PATH}/ble.mk
+$(eval $(call MAKE_BL,ble))
+
+clean realclean distclean: mrvl_clean
+
+.PHONY: mrvl_clean
+mrvl_clean:
+	@echo "  Doimage CLEAN"
+	${Q}${MAKE} PLAT=${PLAT} --no-print-directory -C ${DOIMAGEPATH} clean
+
+${DOIMAGETOOL}: FORCE
+	@$(DOIMAGE_LIBS_CHECK)
+	${Q}${MAKE} --no-print-directory -C ${DOIMAGEPATH}
+
+${BUILD_PLAT}/${FLASH_IMAGE}: ${ROM_BIN_EXT} ${BUILD_PLAT}/${BOOT_IMAGE} ${DOIMAGETOOL}
+	@${ECHO_BLANK_LINE}
+	@echo "Building flash image"
+	${Q}${DOIMAGETOOL} ${DOIMAGE_FLAGS} ${BUILD_PLAT}/${BOOT_IMAGE} ${BUILD_PLAT}/${FLASH_IMAGE}
+	@${ECHO_BLANK_LINE}
+	@echo "Built $@ successfully"
+	@${ECHO_BLANK_LINE}
diff --git a/plat/marvell/armada/a8k/common/aarch64/a8k_common.c b/plat/marvell/armada/a8k/common/aarch64/a8k_common.c
new file mode 100644
index 0000000..4332a76
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/aarch64/a8k_common.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <plat_marvell.h>
+
+
+/* MMU entry for internal (register) space access */
+#define MAP_DEVICE0	MAP_REGION_FLAT(DEVICE0_BASE,			\
+					DEVICE0_SIZE,			\
+					MT_DEVICE | MT_RW | MT_SECURE)
+
+/*
+ * Table of regions for various BL stages to map using the MMU.
+ */
+#if IMAGE_BL1
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SECURE_RAM,
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+#if IMAGE_BL2
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SECURE_RAM,
+	MAP_DEVICE0,
+	MARVELL_MAP_DRAM,
+#ifdef SPD_opteed
+	MARVELL_MAP_OPTEE_CORE_MEM,
+	MARVELL_OPTEE_PAGEABLE_LOAD_MEM,
+#endif
+	{0}
+};
+#endif
+
+#if IMAGE_BL2U
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SECURE_RAM,
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+
+#if IMAGE_BLE
+const mmap_region_t plat_marvell_mmap[] = {
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+
+#if IMAGE_BL31
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SECURE_RAM,
+	MAP_DEVICE0,
+	MARVELL_MAP_DRAM,
+	{0}
+};
+#endif
+#if IMAGE_BL32
+const mmap_region_t plat_marvell_mmap[] = {
+	MARVELL_MAP_SECURE_RAM,
+	MAP_DEVICE0,
+	{0}
+};
+#endif
+
+MARVELL_CASSERT_MMAP;
diff --git a/plat/marvell/armada/a8k/common/aarch64/plat_arch_config.c b/plat/marvell/armada/a8k/common/aarch64/plat_arch_config.c
new file mode 100644
index 0000000..d576514
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/aarch64/plat_arch_config.c
@@ -0,0 +1,95 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/marvell/cache_llc.h>
+#include <lib/mmio.h>
+#include <plat/common/platform.h>
+
+#define CCU_HTC_ASET			(MVEBU_CCU_BASE(MVEBU_AP0) + 0x264)
+#define MVEBU_IO_AFFINITY		(0xF00)
+#define MVEBU_SF_REG			(MVEBU_REGS_BASE + 0x40)
+#define MVEBU_SF_EN			BIT(8)
+#define MVEBU_DFX_REG(cluster_id)	(MVEBU_REGS_BASE + 0x6F82A0 + \
+					(cluster_id) * 0x4)
+#define MVEBU_DFX_CLK_EN_POS		0x3
+#define MVEBU_DFX_CL0_CLK_OFFS		16
+#define MVEBU_DFX_CL0_CLK_MASK		(0xF << MVEBU_DFX_CL0_CLK_OFFS)
+#define MVEBU_DFX_CL1_CLK_OFFS		8
+#define MVEBU_DFX_CL1_CLK_MASK		(0xF << MVEBU_DFX_CL1_CLK_OFFS)
+
+#ifdef MVEBU_SOC_AP807
+static void plat_enable_snoop_filter(void)
+{
+	int cpu_id = plat_my_core_pos();
+
+	/* Snoop filter needs to be enabled once per cluster */
+	if (cpu_id % 2)
+		return;
+
+	mmio_setbits_32(MVEBU_SF_REG, MVEBU_SF_EN);
+}
+#endif
+
+#ifndef MVEBU_SOC_AP807
+static void plat_config_dfx_clock(void)
+{
+	int cluster_id = plat_my_core_pos();
+	uint32_t val;
+
+	/* DFX clock needs to be configured once per cluster */
+	if ((cluster_id % PLAT_MAX_CPUS_PER_CLUSTER) != 0) {
+		return;
+	}
+
+	val = mmio_read_32(MVEBU_DFX_REG(cluster_id / PLAT_MAX_CPUS_PER_CLUSTER));
+	if (cluster_id == 0) {
+		val &= ~MVEBU_DFX_CL0_CLK_MASK;
+		val |= (MVEBU_DFX_CLK_EN_POS << MVEBU_DFX_CL0_CLK_OFFS);
+	} else {
+		val &= ~MVEBU_DFX_CL1_CLK_MASK;
+		val |= (MVEBU_DFX_CLK_EN_POS << MVEBU_DFX_CL1_CLK_OFFS);
+	}
+	mmio_write_32(MVEBU_DFX_REG(cluster_id / PLAT_MAX_CPUS_PER_CLUSTER), val);
+}
+#endif
+
+static void plat_enable_affinity(void)
+{
+	int cluster_id;
+	int affinity;
+
+	/* set CPU Affinity */
+	cluster_id = plat_my_core_pos() / PLAT_MARVELL_CLUSTER_CORE_COUNT;
+	affinity = (MVEBU_IO_AFFINITY | (1 << cluster_id));
+	mmio_write_32(CCU_HTC_ASET, affinity);
+
+	/* set barier */
+	isb();
+}
+
+void marvell_psci_arch_init(int die_index)
+{
+#if LLC_ENABLE
+	/* check if LLC is in exclusive mode
+	 * as L2 is configured to UniqueClean eviction
+	 * (in a8k reset handler)
+	 */
+	if (llc_is_exclusive(0) == 0)
+		ERROR("LLC should be configured to exclusice mode\n");
+#endif
+
+	/* Enable Affinity */
+	plat_enable_affinity();
+
+#ifdef MVEBU_SOC_AP807
+	plat_enable_snoop_filter();
+#else
+	plat_config_dfx_clock();
+#endif
+}
diff --git a/plat/marvell/armada/a8k/common/aarch64/plat_helpers.S b/plat/marvell/armada/a8k/common/aarch64/plat_helpers.S
new file mode 100644
index 0000000..fadc4c2
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/aarch64/plat_helpers.S
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <asm_macros.S>
+#include <platform_def.h>
+#include <marvell_pm.h>
+
+	.globl	plat_secondary_cold_boot_setup
+	.globl	plat_get_my_entrypoint
+	.globl	plat_is_my_cpu_primary
+	.globl  plat_reset_handler
+
+	/* -----------------------------------------------------
+	 * void plat_secondary_cold_boot_setup (void);
+	 *
+	 * This function performs any platform specific actions
+	 * needed for a secondary cpu after a cold reset. Right
+	 * now this is a stub function.
+	 * -----------------------------------------------------
+	 */
+func plat_secondary_cold_boot_setup
+	mov	x0, #0
+	ret
+endfunc plat_secondary_cold_boot_setup
+
+	/* ---------------------------------------------------------------------
+	 * unsigned long plat_get_my_entrypoint (void);
+	 *
+	 * Main job of this routine is to distinguish
+	 * between a cold and warm boot
+	 * For a cold boot, return 0.
+	 * For a warm boot, read the mailbox and return the address it contains.
+	 *
+	 * ---------------------------------------------------------------------
+	 */
+func plat_get_my_entrypoint
+	/* Read first word and compare it with magic num */
+	mov_imm x0, PLAT_MARVELL_MAILBOX_BASE
+	ldr     x1, [x0]
+	mov_imm x2, MVEBU_MAILBOX_MAGIC_NUM
+	cmp     x1, x2
+	beq     warm_boot  /* If compare failed, return 0, i.e. cold boot */
+	mov     x0, #0
+	ret
+warm_boot:
+	mov_imm x1, MBOX_IDX_SEC_ADDR		/* Get the jump address */
+	subs	x1, x1, #1
+	mov	x2, #(MBOX_IDX_SEC_ADDR * 8)
+	lsl	x3, x2, x1
+	add     x0, x0, x3
+	ldr     x0, [x0]
+	ret
+endfunc plat_get_my_entrypoint
+
+	/* -----------------------------------------------------
+	 * unsigned int plat_is_my_cpu_primary (void);
+	 *
+	 * Find out whether the current cpu is the primary
+	 * cpu.
+	 * -----------------------------------------------------
+	 */
+func plat_is_my_cpu_primary
+	mrs	x0, mpidr_el1
+	and	x0, x0, #(MPIDR_CLUSTER_MASK | MPIDR_CPU_MASK)
+	cmp	x0, #MVEBU_PRIMARY_CPU
+	cset	w0, eq
+	ret
+endfunc plat_is_my_cpu_primary
+
+        /* -----------------------------------------------------
+	 * void plat_reset_handler (void);
+         *
+	 * Platform specific configuration right after cpu is
+	 * is our of reset.
+	 *
+         * The plat_reset_handler can clobber x0 - x18, x30.
+         * -----------------------------------------------------
+         */
+func plat_reset_handler
+	/*
+	 * Note: the configurations below  should be done before MMU,
+	 *	  I Cache and L2are enabled.
+	 *	  The reset handler is executed right after reset
+	 * 	  and before Caches are enabled.
+	 */
+
+	/* Enable L1/L2 ECC and Parity */
+	mrs x5, s3_1_c11_c0_2  /* L2 Ctrl */
+	orr x5, x5, #(1 << 21) /* Enable L1/L2 cache ECC & Parity */
+	msr s3_1_c11_c0_2, x5  /* L2 Ctrl */
+
+#if LLC_ENABLE
+	/*
+	 * Enable L2 UniqueClean evictions
+	 *  Note: this configuration assumes that LLC is configured
+	 *	  in exclusive mode.
+	 *	  Later on in the code this assumption will be validated
+	 */
+	mrs x5, s3_1_c15_c0_0  /* L2 Ctrl */
+	orr x5, x5, #(1 << 14) /* Enable UniqueClean evictions with data */
+	msr s3_1_c15_c0_0, x5  /* L2 Ctrl */
+#endif
+
+	/* Instruction Barrier to allow msr command completion */
+	isb
+
+        ret
+endfunc plat_reset_handler
diff --git a/plat/marvell/armada/a8k/common/ble/ble.ld.S b/plat/marvell/armada/a8k/common/ble/ble.ld.S
new file mode 100644
index 0000000..446849b
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/ble/ble.ld.S
@@ -0,0 +1,76 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+OUTPUT_FORMAT(PLATFORM_LINKER_FORMAT)
+OUTPUT_ARCH(PLATFORM_LINKER_ARCH)
+ENTRY(ble_main)
+
+MEMORY {
+    RAM (rwx): ORIGIN = BLE_BASE, LENGTH = BLE_LIMIT - BLE_BASE
+}
+
+SECTIONS
+{
+    . = BLE_BASE;
+
+    .ro . : {
+        __RO_START__ = .;
+        *ble_main.o(.entry*)
+        *(.text*)
+        *(.rodata*)
+        __RO_END_UNALIGNED__ = .;
+        __RO_END__ = .;
+    } >RAM
+
+    /*
+     * Define a linker symbol to mark start of the RW memory area for this
+     * image.
+     */
+    __RW_START__ = . ;
+
+    .data . : {
+        __DATA_START__ = .;
+        *(.data*)
+        __DATA_END__ = .;
+    } >RAM
+
+    .stacks . (NOLOAD) : {
+        __STACKS_START__ = .;
+        *(.tzfw_normal_stacks)
+        __STACKS_END__ = .;
+    } >RAM
+
+    .bss : {
+        __BSS_START__ = .;
+        *(.bss*)
+        __BSS_END__ = .;
+    } >RAM
+
+   /*
+    * Extend the BLE binary to the maximum size allocated for it in platform
+    * definition files and prevent overlapping between BLE BSS section and
+    * additional extensions that can follow the BLE in flash image preamble.
+    * This situation happens for instance when secure extension is added to
+    * the image preamble.
+    */
+   .fill LOADADDR(.bss) + SIZEOF(.bss) : {
+       FILL(0xDEADC0DE);
+       . = ORIGIN(RAM) + LENGTH(RAM) - 1;
+       BYTE(0x00)
+   } >RAM
+
+    /*
+     * Define a linker symbol to mark end of the RW memory area for this
+     * image.
+     */
+    __RW_END__ = .;
+    __BLE_END__ = .;
+
+    __BSS_SIZE__ = SIZEOF(.bss);
+}
diff --git a/plat/marvell/armada/a8k/common/ble/ble.mk b/plat/marvell/armada/a8k/common/ble/ble.mk
new file mode 100644
index 0000000..752ab41
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/ble/ble.mk
@@ -0,0 +1,35 @@
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+
+MV_DDR_LIB		=	$(BUILD_PLAT)/ble/mv_ddr_lib.a
+LIBC_LIB		=	$(BUILD_PLAT)/lib/libc.a
+BLE_LIBS		=	$(MV_DDR_LIB) $(LIBC_LIB)
+PLAT_MARVELL		=	plat/marvell/armada
+
+BLE_SOURCES		+= 	$(BLE_PATH)/ble_main.c				\
+				$(BLE_PATH)/ble_mem.S				\
+				drivers/delay_timer/delay_timer.c		\
+				drivers/marvell/iob.c				\
+				$(PLAT_MARVELL)/common/aarch64/marvell_helpers.S \
+				$(PLAT_MARVELL)/common/plat_delay_timer.c	\
+				$(PLAT_MARVELL)/common/marvell_console.c
+
+MV_DDR_INCLUDES		:=	-I$(CURDIR)/include				\
+				-I$(CURDIR)/include/arch/aarch64		\
+				-I$(CURDIR)/include/lib/libc			\
+				-I$(CURDIR)/include/lib/libc/aarch64
+
+BLE_DEFAULT_LINKER_SCRIPT_SOURCE := $(BLE_PATH)/ble.ld.S
+
+BLE_OBJS := $(addprefix $(BUILD_PLAT)/ble/,$(call SOURCES_TO_OBJS,$(BLE_SOURCES)))
+$(BLE_OBJS): PLAT_INCLUDES += -I$(MV_DDR_PATH)
+$(BLE_OBJS): $(MV_DDR_LIB)
+
+$(MV_DDR_LIB): FORCE
+#	Do not remove! Following checks are required to ensure correct TF-A builds, removing these checks leads to broken TF-A builds
+	$(if $(value MV_DDR_PATH),,$(error "Platform '$(PLAT)' for BLE requires MV_DDR_PATH. Please set MV_DDR_PATH to point to the right directory"))
+	$(if $(wildcard $(value MV_DDR_PATH)/*),,$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' directory does not exist"))
+	$(if $(shell git -C $(value MV_DDR_PATH) rev-parse --show-cdup 2>&1),$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' does not contain valid mv-ddr-marvell git repository"))
+	@+make -C $(MV_DDR_PATH) --no-print-directory PLAT_INCLUDES="$(MV_DDR_INCLUDES)" PLATFORM=$(PLAT) ARCH=AARCH64 OBJ_DIR=$(BUILD_PLAT)/ble
diff --git a/plat/marvell/armada/a8k/common/ble/ble_main.c b/plat/marvell/armada/a8k/common/ble/ble_main.c
new file mode 100644
index 0000000..5b3acec
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/ble/ble_main.c
@@ -0,0 +1,99 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <string.h>
+
+#include <platform_def.h>
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/console.h>
+
+#include <marvell_plat_priv.h>
+#include <marvell_pm.h>
+#include <plat_marvell.h>
+
+#define BR_FLAG_SILENT		0x1
+#define SKIP_IMAGE_CODE		0xDEADB002
+
+void mailbox_clean(void)
+{
+	uintptr_t *mailbox = (void *)PLAT_MARVELL_MAILBOX_BASE;
+
+	memset(mailbox, 0, PLAT_MARVELL_MAILBOX_SIZE);
+}
+
+int exec_ble_main(int bootrom_flags)
+{
+	int skip = 0;
+	uintptr_t *mailbox = (void *)PLAT_MARVELL_MAILBOX_BASE;
+
+	/*
+	 * In some situations, like boot from UART, bootrom will
+	 * request to avoid printing to console. in that case don't
+	 * initialize the console and prints will be ignored
+	 */
+	if ((bootrom_flags & BR_FLAG_SILENT) == 0)
+		marvell_console_boot_init();
+
+	NOTICE("Starting binary extension\n");
+
+	/* initialize time (for delay functionality) */
+	plat_delay_timer_init();
+
+	ble_plat_setup(&skip);
+
+	/* if there's skip image request, bootrom will load from the image
+	 * saved on the next address of the flash
+	 */
+	if (skip)
+		return SKIP_IMAGE_CODE;
+
+	/*
+	 * Check if the mailbox magic number is stored at index MBOX_IDX_MAGIC
+	 * and the suspend to RAM magic number at index MBOX_IDX_SUSPEND_MAGIC.
+	 * If the above is true, this is the recovery from suspend to RAM state.
+	 * In such case the mailbox should remain intact, since it stores the
+	 * warm boot jump address to be used by the TF-A in BL31.
+	 * Othervise the mailbox should be cleaned from a garbage data.
+	 */
+	if (mailbox[MBOX_IDX_MAGIC] != MVEBU_MAILBOX_MAGIC_NUM ||
+	    mailbox[MBOX_IDX_SUSPEND_MAGIC] != MVEBU_MAILBOX_SUSPEND_STATE) {
+		NOTICE("Cold boot\n");
+		mailbox_clean();
+	} else {
+		void (*bootrom_exit)(void) =
+			(void (*)(void))mailbox[MBOX_IDX_ROM_EXIT_ADDR];
+
+		INFO("Recovery...\n");
+		/*
+		 * If this is recovery from suspend, two things has to be done:
+		 * 1. Define the DRAM region as executable memory for preparing
+		 *    jump to TF-A
+		 * 2. Instead of returning control to the BootROM, invalidate
+		 *    and flush caches, and continue execution at address stored
+		 *    in the mailbox.
+		 * This should be done until the BootROM have a native support
+		 * for the system restore flow.
+		 */
+		marvell_ble_prepare_exit();
+		bootrom_exit();
+	}
+
+	return 0;
+}
+
+/* NOTE: don't notify this function, all code must be added to exec_ble_main
+ * in order to keep the end of ble_main as a fixed address.
+ */
+int  __attribute__ ((section(".entry"))) ble_main(int bootrom_flags)
+{
+	volatile int ret;
+
+	ret = exec_ble_main(bootrom_flags);
+	return ret;
+}
diff --git a/plat/marvell/armada/a8k/common/ble/ble_mem.S b/plat/marvell/armada/a8k/common/ble/ble_mem.S
new file mode 100644
index 0000000..a48d546
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/ble/ble_mem.S
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <asm_macros.S>
+#include <marvell_def.h>
+#include <platform_def.h>
+
+#define PTE_NON_EXEC_OFF	54	/* XN - eXecute Never bit offset - see VMSAv8-64 */
+
+	.globl marvell_ble_prepare_exit
+
+func marvell_ble_prepare_exit
+	/*
+	 * Read the page table base and set the first page to be executable.
+	 * This is required for jumping to DRAM for further execution.
+	 */
+	mrs	x0, ttbr0_el3
+	ldr     x1, [x0]
+	mov	x2, #1
+	bic	x1, x1, x2, lsl #PTE_NON_EXEC_OFF
+	str	x1, [x0]
+	tlbi	alle3
+	dsb	sy
+	isb
+	ret
+endfunc marvell_ble_prepare_exit
diff --git a/plat/marvell/armada/a8k/common/include/a8k_plat_def.h b/plat/marvell/armada/a8k/common/include/a8k_plat_def.h
new file mode 100644
index 0000000..3a0fd4b
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/include/a8k_plat_def.h
@@ -0,0 +1,195 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef A8K_PLAT_DEF_H
+#define A8K_PLAT_DEF_H
+
+#include <marvell_def.h>
+
+#define MVEBU_PRIMARY_CPU		0x0
+#define MVEBU_AP0			0x0
+
+/* APN806 revision ID */
+#define MVEBU_CSS_GWD_CTRL_IIDR2_REG	(MVEBU_REGS_BASE + 0x610FCC)
+#define GWD_IIDR2_REV_ID_OFFSET		12
+#define GWD_IIDR2_REV_ID_MASK		0xF
+#define GWD_IIDR2_CHIP_ID_OFFSET	20
+#define GWD_IIDR2_CHIP_ID_MASK		(0xFFFu << GWD_IIDR2_CHIP_ID_OFFSET)
+
+#define CHIP_ID_AP806			0x806
+#define CHIP_ID_AP807			0x807
+
+#define COUNTER_FREQUENCY		25000000
+
+#define MVEBU_REGS_BASE			0xF0000000
+#define MVEBU_REGS_BASE_MASK		0xF0000000
+#define MVEBU_REGS_BASE_AP(ap)		MVEBU_REGS_BASE
+#define MVEBU_AP_IO_BASE(ap)		0xF2000000
+#define MVEBU_CP_OFFSET			0x2000000
+#define MVEBU_CP_REGS_BASE(cp_index)	(MVEBU_AP_IO_BASE(0) + \
+						(cp_index) * MVEBU_CP_OFFSET)
+#define MVEBU_RFU_BASE			(MVEBU_REGS_BASE + 0x6F0000)
+#define MVEBU_IO_WIN_BASE(ap_index)	(MVEBU_RFU_BASE)
+#define MVEBU_IO_WIN_GCR_OFFSET		(0x70)
+#define MVEBU_IO_WIN_MAX_WINS		(7)
+
+/* Misc SoC configurations Base */
+#define MVEBU_MISC_SOC_BASE		(MVEBU_REGS_BASE + 0x6F4300)
+
+#define MVEBU_CCU_BASE(ap_index)	(MVEBU_REGS_BASE + 0x4000)
+#define MVEBU_CCU_MAX_WINS		(8)
+
+#define MVEBU_LLC_BASE(ap_index)	(MVEBU_REGS_BASE + 0x8000)
+#define MVEBU_DRAM_MAC_BASE		(MVEBU_REGS_BASE + 0x20000)
+#define MVEBU_DRAM_PHY_BASE		(MVEBU_REGS_BASE + 0x20000)
+#define MVEBU_SMMU_BASE			(MVEBU_REGS_BASE + 0x100000)
+#define MVEBU_CP_MPP_REGS(cp_index, n)	(MVEBU_CP_REGS_BASE(cp_index) + \
+						0x440000 + ((n) << 2))
+#define MVEBU_PM_MPP_REGS(cp_index, n)	(MVEBU_CP_REGS_BASE(cp_index) + \
+						0x440000 + ((n / 8) << 2))
+#define MVEBU_CP_GPIO_DATA_OUT(cp_index, n) \
+					(MVEBU_CP_REGS_BASE(cp_index) + \
+					0x440100 + ((n > 31) ? 0x40 : 0x00))
+#define MVEBU_CP_GPIO_DATA_OUT_EN(cp_index, n) \
+					(MVEBU_CP_REGS_BASE(cp_index) + \
+					0x440104 + ((n > 31) ? 0x40 : 0x00))
+#define MVEBU_CP_GPIO_DATA_IN(cp_index, n) (MVEBU_CP_REGS_BASE(cp_index) + \
+					0x440110 + ((n > 31) ? 0x40 : 0x00))
+#define MVEBU_AP_MPP_REGS(n)		(MVEBU_RFU_BASE + 0x4000 + ((n) << 2))
+#define MVEBU_AP_GPIO_REGS		(MVEBU_RFU_BASE + 0x5040)
+#define MVEBU_AP_GPIO_DATA_IN		(MVEBU_AP_GPIO_REGS + 0x10)
+#define MVEBU_AP_I2C_BASE		(MVEBU_REGS_BASE + 0x511000)
+#define MVEBU_CP0_I2C_BASE		(MVEBU_CP_REGS_BASE(0) + 0x701000)
+#define MVEBU_AP_GEN_MGMT_BASE		(MVEBU_RFU_BASE + 0x8000)
+#define MVEBU_AP_EXT_TSEN_BASE		(MVEBU_AP_GEN_MGMT_BASE + 0x84)
+
+#define MVEBU_AP_MC_TRUSTZONE_REG_LOW(ap, win)	(MVEBU_REGS_BASE_AP(ap) + \
+							0x20080 + ((win) * 0x8))
+#define MVEBU_AP_MC_TRUSTZONE_REG_HIGH(ap, win)	(MVEBU_REGS_BASE_AP(ap) + \
+							0x20084 + ((win) * 0x8))
+
+/* MCI indirect access definitions */
+#define MCI_MAX_UNIT_ID				2
+/* SoC RFU / IHBx4 Control */
+#define MCIX4_REG_START_ADDRESS_REG(unit_id)	(MVEBU_RFU_BASE + \
+						0x4218 + (unit_id * 0x20))
+#define MCI_REMAP_OFF_SHIFT			8
+
+#define MVEBU_MCI_REG_BASE_REMAP(index)		(0xFD000000 + \
+						((index) * 0x1000000))
+
+#define MVEBU_PCIE_X4_MAC_BASE(x)	(MVEBU_CP_REGS_BASE(x) + 0x600000)
+#define MVEBU_COMPHY_BASE(x)		(MVEBU_CP_REGS_BASE(x) + 0x441000)
+#define MVEBU_HPIPE_BASE(x)		(MVEBU_CP_REGS_BASE(x) + 0x120000)
+#define MVEBU_CP_DFX_OFFSET		(0x400200)
+
+/*****************************************************************************
+ * MVEBU memory map related constants
+ *****************************************************************************
+ */
+/* Aggregate of all devices in the first GB */
+#define DEVICE0_BASE			MVEBU_REGS_BASE
+#define DEVICE0_SIZE			0x10000000
+
+/*****************************************************************************
+ * GIC-400 & interrupt handling related constants
+ *****************************************************************************
+ */
+/* Base MVEBU compatible GIC memory map */
+#define MVEBU_GICD_BASE			0x210000
+#define MVEBU_GICC_BASE			0x220000
+
+
+/*****************************************************************************
+ * AXI Configuration
+ *****************************************************************************
+ */
+#define MVEBU_AXI_ATTR_ARCACHE_OFFSET		4
+#define MVEBU_AXI_ATTR_ARCACHE_MASK		(0xF << \
+						 MVEBU_AXI_ATTR_ARCACHE_OFFSET)
+#define MVEBU_AXI_ATTR_ARDOMAIN_OFFSET		12
+#define MVEBU_AXI_ATTR_ARDOMAIN_MASK		(0x3 << \
+						 MVEBU_AXI_ATTR_ARDOMAIN_OFFSET)
+#define MVEBU_AXI_ATTR_AWCACHE_OFFSET		20
+#define MVEBU_AXI_ATTR_AWCACHE_MASK		(0xF << \
+						 MVEBU_AXI_ATTR_AWCACHE_OFFSET)
+#define MVEBU_AXI_ATTR_AWDOMAIN_OFFSET		28
+#define MVEBU_AXI_ATTR_AWDOMAIN_MASK		(0x3 << \
+						 MVEBU_AXI_ATTR_AWDOMAIN_OFFSET)
+
+/* SATA MBUS to AXI configuration */
+#define MVEBU_SATA_M2A_AXI_ARCACHE_OFFSET	1
+#define MVEBU_SATA_M2A_AXI_ARCACHE_MASK		(0xF << \
+					MVEBU_SATA_M2A_AXI_ARCACHE_OFFSET)
+#define MVEBU_SATA_M2A_AXI_AWCACHE_OFFSET	5
+#define MVEBU_SATA_M2A_AXI_AWCACHE_MASK		(0xF << \
+					MVEBU_SATA_M2A_AXI_AWCACHE_OFFSET)
+
+/* ARM cache attributes */
+#define CACHE_ATTR_BUFFERABLE			0x1
+#define CACHE_ATTR_CACHEABLE			0x2
+#define CACHE_ATTR_READ_ALLOC			0x4
+#define CACHE_ATTR_WRITE_ALLOC			0x8
+/* Domain */
+#define DOMAIN_NON_SHAREABLE			0x0
+#define DOMAIN_INNER_SHAREABLE			0x1
+#define DOMAIN_OUTER_SHAREABLE			0x2
+#define DOMAIN_SYSTEM_SHAREABLE			0x3
+
+/************************************************************************
+ * Required platform porting definitions common to all
+ * Management Compute SubSystems (MSS)
+ ************************************************************************
+ */
+/*
+ * Load address of SCP_BL2
+ * SCP_BL2 is loaded to the same place as BL31.
+ * Once SCP_BL2 is transferred to the SCP,
+ * it is discarded and BL31 is loaded over the top.
+ */
+#ifdef SCP_IMAGE
+#define SCP_BL2_BASE			BL31_BASE
+#define SCP_BL2_SIZE			BL31_LIMIT
+#endif
+
+#ifndef __ASSEMBLER__
+enum ap806_sar_target_dev {
+	SAR_PIDI_MCIX2		= 0x0,
+	SAR_MCIX4		= 0x1,
+	SAR_SPI			= 0x2,
+	SAR_SD			= 0x3,
+	SAR_PIDI_MCIX2_BD	= 0x4, /* BootRom disabled */
+	SAR_MCIX4_DB		= 0x5, /* BootRom disabled */
+	SAR_SPI_DB		= 0x6, /* BootRom disabled */
+	SAR_EMMC		= 0x7
+};
+
+enum io_win_target_ids {
+	MCI_0_TID	 = 0x0,
+	MCI_1_TID	 = 0x1,
+	MCI_2_TID	 = 0x2,
+	PIDI_TID	 = 0x3,
+	SPI_TID		 = 0x4,
+	STM_TID		 = 0x5,
+	BOOTROM_TID	 = 0x6,
+	IO_WIN_MAX_TID
+};
+
+enum ccu_target_ids {
+	IO_0_TID        = 0x00,
+	DRAM_0_TID      = 0x03,
+	IO_1_TID        = 0x0F,
+	CFG_REG_TID     = 0x10,
+	RAR_TID         = 0x20,
+	SRAM_TID        = 0x40,
+	DRAM_1_TID      = 0xC0,
+	CCU_MAX_TID,
+	INVALID_TID     = 0xFF
+};
+#endif /* __ASSEMBLER__ */
+
+#endif /* A8K_PLAT_DEF_H */
diff --git a/plat/marvell/armada/a8k/common/include/ddr_info.h b/plat/marvell/armada/a8k/common/include/ddr_info.h
new file mode 100644
index 0000000..e19036a
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/include/ddr_info.h
@@ -0,0 +1,9 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#define DRAM_MAX_IFACE			1
+#define DRAM_CH0_MMAP_LOW_OFFSET	0x20200
diff --git a/plat/marvell/armada/a8k/common/include/mentor_i2c_plat.h b/plat/marvell/armada/a8k/common/include/mentor_i2c_plat.h
new file mode 100644
index 0000000..e03c448
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/include/mentor_i2c_plat.h
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+/* This driver provides I2C support for Marvell A8K and compatible SoCs */
+
+#ifndef MENTOR_I2C_PLAT_H
+#define MENTOR_I2C_PLAT_H
+
+#define CONFIG_SYS_TCLK			250000000
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		0x0
+
+#define I2C_CAN_UNSTUCK
+
+struct  mentor_i2c_regs {
+	uint32_t slave_address;
+	uint32_t data;
+	uint32_t control;
+	union {
+		uint32_t status;	/* when reading */
+		uint32_t baudrate;	/* when writing */
+	};
+	uint32_t xtnd_slave_addr;
+	uint32_t reserved[2];
+	uint32_t soft_reset;
+	uint8_t  reserved2[0xa0 - 0x20];
+	uint32_t unstuck;
+};
+
+#endif /* MENTOR_I2C_PLAT_H */
diff --git a/plat/marvell/armada/a8k/common/include/plat_macros.S b/plat/marvell/armada/a8k/common/include/plat_macros.S
new file mode 100644
index 0000000..8faccf0
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/include/plat_macros.S
@@ -0,0 +1,20 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef PLAT_MACROS_S
+#define PLAT_MACROS_S
+
+#include <marvell_macros.S>
+
+/*
+ * Required platform porting macros
+ * (Provided by included headers)
+ */
+.macro plat_crash_print_regs
+.endm
+
+#endif /* PLAT_MACROS_S */
diff --git a/plat/marvell/armada/a8k/common/include/platform_def.h b/plat/marvell/armada/a8k/common/include/platform_def.h
new file mode 100644
index 0000000..45860ba
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/include/platform_def.h
@@ -0,0 +1,196 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef PLATFORM_DEF_H
+#define PLATFORM_DEF_H
+
+#ifndef __ASSEMBLER__
+#include <stdio.h>
+#endif /* __ASSEMBLER__ */
+
+#include <common/interrupt_props.h>
+#include <drivers/arm/gic_common.h>
+
+#include <board_marvell_def.h>
+#include <mvebu_def.h>
+
+/*
+ * Most platform porting definitions provided by included headers
+ */
+
+/*
+ * DRAM Memory layout:
+ *		+-----------------------+
+ *		:			:
+ *		:	Linux		:
+ * 0x04X00000-->+-----------------------+
+ *		|	BL3-3(u-boot)	|>>}>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
+ *		|-----------------------|  }				       |
+ *		|	BL3-[0,1, 2]	|  }---------------------------------> |
+ *		|-----------------------|  }				||     |
+ *		|	BL2		|  }->FIP (loaded by            ||     |
+ *		|-----------------------|  }       BootROM to DRAM)     ||     |
+ *		|	FIP_TOC		|  }                            ||     |
+ * 0x04120000-->|-----------------------|				||     |
+ *		|	BL1 (RO)	|				||     |
+ * 0x04100000-->+-----------------------+				||     |
+ *		:			:				||     |
+ *		: Trusted SRAM section	:				\/     |
+ * 0x04040000-->+-----------------------+  Replaced by BL2  +----------------+ |
+ *		|	BL1 (RW)	|  <<<<<<<<<<<<<<<< | BL3-1 NOBITS   | |
+ * 0x04037000-->|-----------------------|  <<<<<<<<<<<<<<<< |----------------| |
+ *		|			|  <<<<<<<<<<<<<<<< | BL3-1 PROGBITS | |
+ * 0x04023000-->|-----------------------|		    +----------------+ |
+ *		|	BL2		|				       |
+ *		|-----------------------|				       |
+ *		|			|				       |
+ * 0x04001000-->|-----------------------|				       |
+ *		|	Shared		|				       |
+ * 0x04000000-->+-----------------------+				       |
+ *		:			:				       |
+ *		:	Linux		:				       |
+ *		:			:				       |
+ *		|-----------------------|				       |
+ *		|			|	U-Boot(BL3-3) Loaded by BL2    |
+ *		|	U-Boot		|	<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
+ * 0x00000000-->+-----------------------+
+ *
+ * Trusted SRAM section 0x4000000..0x4200000:
+ * ----------------------------------------
+ * SRAM_BASE		= 0x4001000
+ * BL2_BASE			= 0x4006000
+ * BL2_LIMIT		= BL31_BASE
+ * BL31_BASE		= 0x4023000 = (64MB + 256KB - 0x1D000)
+ * BL31_PROGBITS_LIMIT	= BL1_RW_BASE
+ * BL1_RW_BASE		= 0x4037000 = (64MB + 256KB - 0x9000)
+ * BL1_RW_LIMIT		= BL31_LIMIT = 0x4040000
+ *
+ *
+ * PLAT_MARVELL_FIP_BASE	= 0x4120000
+ */
+
+#define PLAT_MARVELL_SRAM_BASE			0xFFE1C048
+#define PLAT_MARVELL_SRAM_END			0xFFE78000
+
+#define PLAT_MARVELL_ATF_BASE			0x4000000
+#define PLAT_MARVELL_ATF_LOAD_ADDR		(PLAT_MARVELL_ATF_BASE + \
+								0x100000)
+
+#define PLAT_MARVELL_FIP_BASE			(PLAT_MARVELL_ATF_LOAD_ADDR + \
+								0x20000)
+#define PLAT_MARVELL_FIP_MAX_SIZE		0x4000000
+
+#define PLAT_MARVELL_NORTHB_COUNT		1
+
+#define PLAT_MARVELL_CLUSTER_COUNT		U(2)
+#define PLAT_MARVELL_CLUSTER_CORE_COUNT		U(2)
+
+#define PLAT_MARVELL_CORE_COUNT			(PLAT_MARVELL_CLUSTER_COUNT * \
+						PLAT_MARVELL_CLUSTER_CORE_COUNT)
+
+#define PLAT_MAX_CPUS_PER_CLUSTER		PLAT_MARVELL_CLUSTER_CORE_COUNT
+
+/* Part of DRAM that is used as Trusted ROM */
+#define PLAT_MARVELL_TRUSTED_ROM_BASE		PLAT_MARVELL_ATF_LOAD_ADDR
+/* 4 MB for FIP image */
+#define PLAT_MARVELL_TRUSTED_ROM_SIZE		0x00400000
+/* Reserve 12MB for SCP (Secure PayLoad) Trusted RAM
+ * OP-TEE 4MB SHMEM follows this region
+ */
+#define PLAT_MARVELL_TRUSTED_RAM_BASE		0x04400000
+#define PLAT_MARVELL_TRUSTED_RAM_SIZE		0x00C00000	/* 12 MB DRAM */
+
+#define PLAT_MARVELL_LLC_SRAM_BASE		0x05400000
+#define PLAT_MARVELL_LLC_SRAM_SIZE		0x00100000	/* 1 MB SRAM */
+
+/*
+ * PLAT_ARM_MAX_BL1_RW_SIZE is calculated using the current BL1 RW debug size
+ * plus a little space for growth.
+ */
+#define PLAT_MARVELL_MAX_BL1_RW_SIZE		0xA000
+
+/*
+ * PLAT_ARM_MAX_BL2_SIZE is calculated using the current BL2 debug size plus a
+ * little space for growth.
+ */
+#define PLAT_MARVELL_MAX_BL2_SIZE		0xF000
+
+/*
+ * PLAT_ARM_MAX_BL31_SIZE is calculated using the current BL31 debug size plus a
+ * little space for growth.
+ */
+#define PLAT_MARVEL_MAX_BL31_SIZE		0x5D000
+
+#define PLAT_MARVELL_CPU_ENTRY_ADDR		BL1_RO_BASE
+
+/* GIC related definitions */
+#define PLAT_MARVELL_GICD_BASE		(MVEBU_REGS_BASE + MVEBU_GICD_BASE)
+#define PLAT_MARVELL_GICC_BASE		(MVEBU_REGS_BASE + MVEBU_GICC_BASE)
+
+#define PLAT_MARVELL_G0_IRQ_PROPS(grp) \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_0, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_6, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_PIC0, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL)
+
+#define PLAT_MARVELL_G1S_IRQ_PROPS(grp) \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_PHY_TIMER, GIC_HIGHEST_SEC_PRIORITY, \
+			grp, GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_1, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_2, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_3, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_4, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_5, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL), \
+	INTR_PROP_DESC(MARVELL_IRQ_SEC_SGI_7, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL)
+
+#define PLAT_MARVELL_SHARED_RAM_CACHED		1
+
+/*
+ * Load address of BL3-3 for this platform port
+ */
+#define PLAT_MARVELL_NS_IMAGE_OFFSET		0x0
+
+/* System Reference Clock*/
+#define PLAT_REF_CLK_IN_HZ			COUNTER_FREQUENCY
+
+/*
+ * PL011 related constants
+ */
+#define PLAT_MARVELL_UART_BASE			(MVEBU_REGS_BASE + 0x512000)
+#define PLAT_MARVELL_UART_CLK_IN_HZ		200000000
+
+/* Recovery image enable */
+#define PLAT_RECOVERY_IMAGE_ENABLE		0
+
+/* Required platform porting definitions */
+#define PLAT_MAX_PWR_LVL			MPIDR_AFFLVL1
+
+/* System timer related constants */
+#define PLAT_MARVELL_NSTIMER_FRAME_ID		1
+
+/* Mailbox base address (note the lower memory space
+ * is reserved for BLE data)
+ */
+#define PLAT_MARVELL_MAILBOX_BASE		(MARVELL_SHARED_RAM_BASE  \
+						+ 0x400)
+#define PLAT_MARVELL_MAILBOX_SIZE		0x100
+#define PLAT_MARVELL_MAILBOX_MAGIC_NUM		0x6D72766C	/* mrvl */
+
+/* Securities */
+#define IRQ_SEC_OS_TICK_INT			MARVELL_IRQ_SEC_PHY_TIMER
+
+#define MVEBU_PMU_IRQ_WA
+
+#endif /* PLATFORM_DEF_H */
diff --git a/plat/marvell/armada/a8k/common/mss/mss_a8k.mk b/plat/marvell/armada/a8k/common/mss/mss_a8k.mk
new file mode 100644
index 0000000..315fc87
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/mss/mss_a8k.mk
@@ -0,0 +1,22 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:	BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PLAT_MARVELL		:=	plat/marvell/armada
+A8K_MSS_SOURCE		:=	$(PLAT_MARVELL)/a8k/common/mss
+
+BL2_SOURCES		+=	$(A8K_MSS_SOURCE)/mss_bl2_setup.c \
+				$(MARVELL_MOCHI_DRV)
+
+BL31_SOURCES		+=	$(A8K_MSS_SOURCE)/mss_pm_ipc.c \
+				$(A8K_MSS_SOURCE)/mss_bl31_setup.c
+
+PLAT_INCLUDES		+=	-I$(A8K_MSS_SOURCE)
+
+ifneq (${SCP_BL2},)
+# This define is used to inidcate the SCP image is present
+$(eval $(call add_define,SCP_IMAGE))
+endif
diff --git a/plat/marvell/armada/a8k/common/mss/mss_bl2_setup.c b/plat/marvell/armada/a8k/common/mss/mss_bl2_setup.c
new file mode 100644
index 0000000..dee2d5b
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/mss/mss_bl2_setup.c
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+#include <common/bl_common.h>
+#include <common/debug.h>
+#include <drivers/marvell/ccu.h>
+#include <drivers/marvell/mochi/ap_setup.h>
+#include <drivers/marvell/mochi/cp110_setup.h>
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+#include <marvell_plat_priv.h> /* timer functionality */
+#include "mss_defs.h"
+#include "mss_scp_bootloader.h"
+
+/* MSS windows configuration */
+#define MSS_AEBR(base)			(base + 0x160)
+#define MSS_AIBR(base)			(base + 0x164)
+#define MSS_AEBR_MASK			0xFFF
+#define MSS_AIBR_MASK			0xFFF
+
+#define MSS_EXTERNAL_SPACE		0x50000000
+#define MSS_EXTERNAL_ACCESS_BIT		28
+#define MSS_EXTERNAL_ADDR_MASK		0xfffffff
+#define MSS_INTERNAL_ACCESS_BIT		28
+
+struct addr_map_win ccu_mem_map[] = {
+	{MVEBU_CP_REGS_BASE(0), 0x4000000, IO_0_TID}
+};
+
+/* Since the scp_bl2 image can contain firmware for cp1 and cp0 coprocessors,
+ * the access to cp0 and cp1 need to be provided. More precisely it is
+ * required to:
+ *  - get the information about device id which is stored in CP0 registers
+ *    (to distinguish between cases where we have cp0 and cp1 or standalone cp0)
+ *  - get the access to cp which is needed for loading fw for cp0/cp1
+ *    coprocessors
+ * This function configures ccu windows accordingly.
+ *
+ * Note: there is no need to restore previous ccu configuration, since in next
+ * phase (BL31) the init_ccu will be called (via apn806_init/
+ * bl31_plat_arch_setu) and therefore the ccu configuration will be overwritten.
+ */
+static int bl2_plat_mmap_init(void)
+{
+	int cfg_num, win_id, cfg_idx, cp;
+
+	cfg_num =  ARRAY_SIZE(ccu_mem_map);
+
+	/* CCU window-0 should not be counted - it's already used */
+	if (cfg_num > (MVEBU_CCU_MAX_WINS - 1)) {
+		ERROR("BL2: %s: trying to open too many windows\n", __func__);
+		return -1;
+	}
+
+	/* Enable required CCU windows
+	 * Do not touch CCU window 0,
+	 * it's used for the internal registers access
+	 */
+	for (cfg_idx = 0, win_id = 1;
+	     (win_id < MVEBU_CCU_MAX_WINS) && (cfg_idx < cfg_num); win_id++) {
+		/* Skip already enabled CCU windows */
+		if (ccu_is_win_enabled(MVEBU_AP0, win_id))
+			continue;
+		/* Enable required CCU windows */
+		ccu_win_check(&ccu_mem_map[cfg_idx]);
+		ccu_enable_win(MVEBU_AP0, &ccu_mem_map[cfg_idx], win_id);
+		cfg_idx++;
+	}
+
+	/* Config address for each cp other than cp0 */
+	for (cp = 1; cp < CP_COUNT; cp++)
+		update_cp110_default_win(cp);
+
+	/* There is need to configure IO_WIN windows again to overwrite
+	 * temporary configuration done during update_cp110_default_win
+	 */
+	init_io_win(MVEBU_AP0);
+
+	/* Open AMB bridge required for MG access */
+	for (cp = 0; cp < CP_COUNT; cp++)
+		cp110_amb_init(MVEBU_CP_REGS_BASE(cp));
+
+	return 0;
+}
+
+/*****************************************************************************
+ * Transfer SCP_BL2 from Trusted RAM using the SCP Download protocol.
+ * Return 0 on success, -1 otherwise.
+ *****************************************************************************
+ */
+int bl2_plat_handle_scp_bl2(image_info_t *scp_bl2_image_info)
+{
+	int ret;
+
+	INFO("BL2: Initiating SCP_BL2 transfer to SCP\n");
+
+	/* initialize time (for delay functionality) */
+	plat_delay_timer_init();
+
+	ret = bl2_plat_mmap_init();
+	if (ret != 0)
+		return ret;
+
+	ret = scp_bootloader_transfer((void *)scp_bl2_image_info->image_base,
+		scp_bl2_image_info->image_size);
+
+	if (ret == 0)
+		INFO("BL2: SCP_BL2 transferred to SCP\n");
+	else
+		ERROR("BL2: SCP_BL2 transfer failure\n");
+
+	return ret;
+}
+
+uintptr_t bl2_plat_get_cp_mss_regs(int ap_idx, int cp_idx)
+{
+	return MVEBU_CP_REGS_BASE(cp_idx) + MSS_CP_REGS_OFFSET;
+}
+
+uintptr_t bl2_plat_get_cp_mss_sram(int ap_idx, int cp_idx)
+{
+	return MVEBU_CP_REGS_BASE(cp_idx) + MSS_CP_SRAM_OFFSET;
+}
+
+uintptr_t bl2_plat_get_ap_mss_regs(int ap_idx)
+{
+	return MVEBU_REGS_BASE + MSS_AP_REGS_OFFSET;
+}
+
+uint32_t bl2_plat_get_cp_count(int ap_idx)
+{
+	uint32_t revision = cp110_device_id_get(MVEBU_CP_REGS_BASE(0));
+	/* A8040: two CPs.
+	 * A7040: one CP.
+	 */
+	if (revision == MVEBU_80X0_DEV_ID ||
+	    revision == MVEBU_80X0_CP115_DEV_ID)
+		return 2;
+	else if (revision == MVEBU_CN9130_DEV_ID)
+		return CP_COUNT;
+	else
+		return 1;
+}
+
+uint32_t bl2_plat_get_ap_count(void)
+{
+	/* A8040 and A7040 have only one AP */
+	return 1;
+}
+
+void bl2_plat_configure_mss_windows(uintptr_t mss_regs)
+{
+	/* set AXI External and Internal Address Bus extension */
+	mmio_write_32(MSS_AEBR(mss_regs),
+		      ((0x0 >> MSS_EXTERNAL_ACCESS_BIT) & MSS_AEBR_MASK));
+	mmio_write_32(MSS_AIBR(mss_regs),
+		      ((mss_regs >> MSS_INTERNAL_ACCESS_BIT) & MSS_AIBR_MASK));
+}
diff --git a/plat/marvell/armada/a8k/common/mss/mss_bl31_setup.c b/plat/marvell/armada/a8k/common/mss/mss_bl31_setup.c
new file mode 100644
index 0000000..52a8929
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/mss/mss_bl31_setup.c
@@ -0,0 +1,37 @@
+/*
+ * Copyright (C) 2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+#include <common/bl_common.h>
+#include <common/debug.h>
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+
+#include "mss_defs.h"
+
+void mss_start_cp_cm3(int cp)
+{
+	uint32_t magic;
+	uintptr_t sram = MVEBU_CP_REGS_BASE(cp) + MSS_CP_SRAM_OFFSET;
+	uintptr_t regs = MVEBU_CP_REGS_BASE(cp) + MSS_CP_REGS_OFFSET;
+
+	magic = mmio_read_32(sram);
+
+	/* Make sure the FW was loaded */
+	if (magic != MSS_FW_READY_MAGIC) {
+		return;
+	}
+
+	NOTICE("Starting CP%d MSS CPU\n", cp);
+	/* remove the magic */
+	mmio_write_32(sram, 0);
+	/* Release M3 from reset */
+	mmio_write_32(MSS_M3_RSTCR(regs),
+		      (MSS_M3_RSTCR_RST_OFF << MSS_M3_RSTCR_RST_OFFSET));
+}
diff --git a/plat/marvell/armada/a8k/common/mss/mss_defs.h b/plat/marvell/armada/a8k/common/mss/mss_defs.h
new file mode 100644
index 0000000..6956461
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/mss/mss_defs.h
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2021 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MSS_DEFS_H
+#define MSS_DEFS_H
+
+#define MSS_DMA_SRCBR(base)		(base + 0xC0)
+#define MSS_DMA_DSTBR(base)		(base + 0xC4)
+#define MSS_DMA_CTRLR(base)		(base + 0xC8)
+#define MSS_M3_RSTCR(base)		(base + 0xFC)
+
+#define MSS_DMA_CTRLR_SIZE_OFFSET	(0)
+#define MSS_DMA_CTRLR_REQ_OFFSET	(15)
+#define MSS_DMA_CTRLR_REQ_SET		(1)
+#define MSS_DMA_CTRLR_ACK_OFFSET	(12)
+#define MSS_DMA_CTRLR_ACK_MASK		(0x1)
+#define MSS_DMA_CTRLR_ACK_READY		(1)
+#define MSS_M3_RSTCR_RST_OFFSET		(0)
+#define MSS_M3_RSTCR_RST_OFF		(1)
+
+#define MSS_FW_READY_MAGIC		0x46575144 /* FWRD */
+
+#define MSS_AP_REGS_OFFSET		0x00580000
+#define MSS_CP_SRAM_OFFSET		0x00220000
+#define MSS_CP_REGS_OFFSET		0x00280000
+
+void mss_start_cp_cm3(int cp);
+
+#endif /* MSS_DEFS_H */
diff --git a/plat/marvell/armada/a8k/common/mss/mss_pm_ipc.c b/plat/marvell/armada/a8k/common/mss/mss_pm_ipc.c
new file mode 100644
index 0000000..a070583
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/mss/mss_pm_ipc.c
@@ -0,0 +1,85 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <string.h>
+
+#include <common/debug.h>
+#include <lib/psci/psci.h>
+#include <lib/mmio.h>
+
+#include <mss_pm_ipc.h>
+
+/*
+ * SISR is 32 bit interrupt register representing 32 interrupts
+ *
+ * +======+=============+=============+
+ * + Bits + 31          + 30 - 00     +
+ * +======+=============+=============+
+ * + Desc + MSS Msg Int + Reserved    +
+ * +======+=============+=============+
+ */
+#define MSS_SISR		(MVEBU_REGS_BASE + 0x5800D0)
+#define MSS_SISTR		(MVEBU_REGS_BASE + 0x5800D8)
+
+#define MSS_MSG_INT_MASK	(0x80000000)
+#define MSS_TIMER_BASE		(MVEBU_REGS_BASE_MASK + 0x580110)
+#define MSS_TRIGGER_TIMEOUT	(2000)
+
+/*****************************************************************************
+ * mss_pm_ipc_msg_send
+ *
+ * DESCRIPTION: create and transmit IPC message
+ *****************************************************************************
+ */
+int mss_pm_ipc_msg_send(unsigned int channel_id, unsigned int msg_id,
+			const psci_power_state_t *target_state)
+{
+	/* Transmit IPC message */
+#ifndef DISABLE_CLUSTER_LEVEL
+	mv_pm_ipc_msg_tx(channel_id, msg_id,
+			 (unsigned int)target_state->pwr_domain_state[
+					MPIDR_AFFLVL1]);
+#else
+	mv_pm_ipc_msg_tx(channel_id, msg_id, 0);
+#endif
+
+	return 0;
+}
+
+/*****************************************************************************
+ * mss_pm_ipc_msg_trigger
+ *
+ * DESCRIPTION: Trigger IPC message interrupt to MSS
+ *****************************************************************************
+ */
+int mss_pm_ipc_msg_trigger(void)
+{
+	unsigned int timeout;
+	unsigned int t_end;
+	unsigned int t_start = mmio_read_32(MSS_TIMER_BASE);
+
+	mmio_write_32(MSS_SISR, MSS_MSG_INT_MASK);
+
+	do {
+		/* wait while SCP process incoming interrupt */
+		if (mmio_read_32(MSS_SISTR) != MSS_MSG_INT_MASK)
+			break;
+
+		/* check timeout */
+		t_end = mmio_read_32(MSS_TIMER_BASE);
+
+		timeout = ((t_start > t_end) ?
+			   (t_start - t_end) : (t_end - t_start));
+		if (timeout > MSS_TRIGGER_TIMEOUT) {
+			ERROR("PM MSG Trigger Timeout\n");
+			break;
+		}
+
+	} while (1);
+
+	return 0;
+}
diff --git a/plat/marvell/armada/a8k/common/mss/mss_pm_ipc.h b/plat/marvell/armada/a8k/common/mss/mss_pm_ipc.h
new file mode 100644
index 0000000..1dfa9fa
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/mss/mss_pm_ipc.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MSS_PM_IPC_H
+#define MSS_PM_IPC_H
+
+#include <mss_ipc_drv.h>
+
+/* Currently MSS does not support Cluster level Power Down */
+#define DISABLE_CLUSTER_LEVEL
+
+
+/*****************************************************************************
+ * mss_pm_ipc_msg_send
+ *
+ * DESCRIPTION: create and transmit IPC message
+ *****************************************************************************
+ */
+int mss_pm_ipc_msg_send(unsigned int channel_id, unsigned int msg_id,
+			const psci_power_state_t *target_state);
+
+/*****************************************************************************
+ * mss_pm_ipc_msg_trigger
+ *
+ * DESCRIPTION: Trigger IPC message interrupt to MSS
+ *****************************************************************************
+ */
+int mss_pm_ipc_msg_trigger(void);
+
+
+#endif /* MSS_PM_IPC_H */
diff --git a/plat/marvell/armada/a8k/common/plat_bl1_setup.c b/plat/marvell/armada/a8k/common/plat_bl1_setup.c
new file mode 100644
index 0000000..f9521c8
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/plat_bl1_setup.c
@@ -0,0 +1,19 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <lib/mmio.h>
+
+#include <plat_marvell.h>
+
+void marvell_bl1_setup_mpps(void)
+{
+	/* Enable UART MPPs.
+	 ** In a normal system, this is done by Bootrom.
+	 */
+	mmio_write_32(MVEBU_AP_MPP_REGS(1), 0x3000);
+	mmio_write_32(MVEBU_AP_MPP_REGS(2), 0x3000);
+}
diff --git a/plat/marvell/armada/a8k/common/plat_bl31_setup.c b/plat/marvell/armada/a8k/common/plat_bl31_setup.c
new file mode 100644
index 0000000..db85cce
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/plat_bl31_setup.c
@@ -0,0 +1,148 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#include <drivers/marvell/mci.h>
+#include <drivers/marvell/mochi/ap_setup.h>
+#include <drivers/marvell/mochi/cp110_setup.h>
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+#include <marvell_plat_priv.h>
+#include <marvell_pm.h>
+#include <mc_trustzone/mc_trustzone.h>
+#include <plat_marvell.h>
+#if MSS_SUPPORT
+#include <mss_ipc_drv.h>
+#include <mss_mem.h>
+#include <mss_defs.h>
+#endif
+
+/* In Armada-8k family AP806/AP807, CP0 connected to PIDI
+ * and CP1 connected to IHB via MCI #0
+ */
+#define MVEBU_MCI0		0
+
+static _Bool pm_fw_running;
+
+/* Set a weak stub for platforms that don't need to configure GPIO */
+#pragma weak marvell_gpio_config
+int marvell_gpio_config(void)
+{
+	return 0;
+}
+
+static void marvell_bl31_mpp_init(int cp)
+{
+	uint32_t reg;
+
+	/* need to do for CP#0 only */
+	if (cp)
+		return;
+
+
+	/*
+	 * Enable CP0 I2C MPPs (MPP: 37-38)
+	 * U-Boot rely on proper MPP settings for I2C EEPROM usage
+	 * (only for CP0)
+	 */
+	reg = mmio_read_32(MVEBU_CP_MPP_REGS(0, 4));
+	mmio_write_32(MVEBU_CP_MPP_REGS(0, 4), reg | 0x2200000);
+}
+
+#if MSS_SUPPORT
+void marvell_bl31_mss_init(void)
+{
+	struct mss_pm_ctrl_block *mss_pm_crtl =
+			(struct mss_pm_ctrl_block *)MSS_SRAM_PM_CONTROL_BASE;
+
+	/* Check that the image was loaded successfully */
+	if (mss_pm_crtl->handshake != HOST_ACKNOWLEDGMENT) {
+		NOTICE("MSS PM is not supported in this build\n");
+		return;
+	}
+
+	/* If we got here it means that the PM firmware is running */
+	pm_fw_running = 1;
+
+	INFO("MSS IPC init\n");
+
+	if (mss_pm_crtl->ipc_state == IPC_INITIALIZED)
+		mv_pm_ipc_init(mss_pm_crtl->ipc_base_address | MVEBU_REGS_BASE);
+}
+#endif
+
+_Bool is_pm_fw_running(void)
+{
+	return pm_fw_running;
+}
+
+/* For TrusTzone we treat the "target" field of addr_map_win
+ * struct as attribute
+ */
+static const struct addr_map_win tz_map[] = {
+	{PLAT_MARVELL_ATF_BASE, 0x200000, TZ_PERM_ABORT}
+};
+
+/* Configure MC TrustZone regions */
+static void marvell_bl31_security_setup(void)
+{
+	int tz_nr, win_id;
+
+	tz_nr = ARRAY_SIZE(tz_map);
+
+	for (win_id = 0; win_id < tz_nr; win_id++)
+		tz_enable_win(MVEBU_AP0, tz_map, win_id);
+}
+
+/* This function overruns the same function in marvell_bl31_setup.c */
+void bl31_plat_arch_setup(void)
+{
+	int cp;
+	uintptr_t *mailbox = (void *)PLAT_MARVELL_MAILBOX_BASE;
+
+	/* initialize the timer for mdelay/udelay functionality */
+	plat_delay_timer_init();
+
+	/* configure apn806 */
+	ap_init();
+
+	/* In marvell_bl31_plat_arch_setup, el3 mmu is configured.
+	 * el3 mmu configuration MUST be called after apn806_init, if not,
+	 * this will cause an hang in init_io_win
+	 * (after setting the IO windows GCR values).
+	 */
+	if (mailbox[MBOX_IDX_MAGIC] != MVEBU_MAILBOX_MAGIC_NUM ||
+	    mailbox[MBOX_IDX_SUSPEND_MAGIC] != MVEBU_MAILBOX_SUSPEND_STATE)
+		marvell_bl31_plat_arch_setup();
+
+	for (cp = 0; cp < CP_COUNT; cp++) {
+		cp110_init(MVEBU_CP_REGS_BASE(cp),
+			   STREAM_ID_BASE + (cp * MAX_STREAM_ID_PER_CP));
+
+		marvell_bl31_mpp_init(cp);
+
+#if MSS_SUPPORT
+		/* Release CP MSS CPU from reset once the CP init is done */
+		mss_start_cp_cm3(cp);
+#endif
+	}
+
+	for (cp = 1; cp < CP_COUNT; cp++)
+		mci_link_tune(cp - 1);
+
+#if MSS_SUPPORT
+	/* initialize IPC between MSS and ATF */
+	if (mailbox[MBOX_IDX_MAGIC] != MVEBU_MAILBOX_MAGIC_NUM ||
+	    mailbox[MBOX_IDX_SUSPEND_MAGIC] != MVEBU_MAILBOX_SUSPEND_STATE)
+		marvell_bl31_mss_init();
+#endif
+	/* Configure GPIO */
+	marvell_gpio_config();
+
+	marvell_bl31_security_setup();
+}
diff --git a/plat/marvell/armada/a8k/common/plat_ble_setup.c b/plat/marvell/armada/a8k/common/plat_ble_setup.c
new file mode 100644
index 0000000..9c5ee15
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/plat_ble_setup.c
@@ -0,0 +1,765 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#include <drivers/marvell/ap807_clocks_init.h>
+#include <drivers/marvell/aro.h>
+#include <drivers/marvell/ccu.h>
+#include <drivers/marvell/io_win.h>
+#include <drivers/marvell/mochi/ap_setup.h>
+#include <drivers/marvell/mochi/cp110_setup.h>
+
+#include <armada_common.h>
+#include <efuse_def.h>
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+/* Register for skip image use */
+#define SCRATCH_PAD_REG2		0xF06F00A8
+#define SCRATCH_PAD_SKIP_VAL		0x01
+#define NUM_OF_GPIO_PER_REG 32
+
+#define MMAP_SAVE_AND_CONFIG		0
+#define MMAP_RESTORE_SAVED		1
+
+/* SAR clock settings */
+#define MVEBU_AP_SAR_REG_BASE(r)	(MVEBU_AP_GEN_MGMT_BASE + 0x200 +\
+								((r) << 2))
+
+#define SAR_CLOCK_FREQ_MODE_OFFSET	(0)
+#define SAR_CLOCK_FREQ_MODE_MASK	(0x1f << SAR_CLOCK_FREQ_MODE_OFFSET)
+#define SAR_PIDI_LOW_SPEED_OFFSET	(20)
+#define SAR_PIDI_LOW_SPEED_MASK		(1 << SAR_PIDI_LOW_SPEED_OFFSET)
+#define SAR_PIDI_LOW_SPEED_SHIFT	(15)
+#define SAR_PIDI_LOW_SPEED_SET		(1 << SAR_PIDI_LOW_SPEED_SHIFT)
+
+#define FREQ_MODE_AP_SAR_REG_NUM	(0)
+#define SAR_CLOCK_FREQ_MODE(v)		(((v) & SAR_CLOCK_FREQ_MODE_MASK) >> \
+					SAR_CLOCK_FREQ_MODE_OFFSET)
+
+#define AVS_I2C_EEPROM_ADDR		0x57	/* EEPROM */
+#define AVS_EN_CTRL_REG			(MVEBU_AP_GEN_MGMT_BASE + 0x130)
+#define AVS_ENABLE_OFFSET		(0)
+#define AVS_SOFT_RESET_OFFSET		(2)
+#define AVS_TARGET_DELTA_OFFSET		(21)
+
+#ifndef MVEBU_SOC_AP807
+	/* AP806 SVC bits */
+	#define AVS_LOW_VDD_LIMIT_OFFSET	(4)
+	#define AVS_HIGH_VDD_LIMIT_OFFSET	(12)
+	#define AVS_VDD_LOW_LIMIT_MASK	(0xFF << AVS_LOW_VDD_LIMIT_OFFSET)
+	#define AVS_VDD_HIGH_LIMIT_MASK	(0xFF << AVS_HIGH_VDD_LIMIT_OFFSET)
+#else
+	/* AP807 SVC bits */
+	#define AVS_LOW_VDD_LIMIT_OFFSET	(3)
+	#define AVS_HIGH_VDD_LIMIT_OFFSET	(13)
+	#define AVS_VDD_LOW_LIMIT_MASK	(0x3FF << AVS_LOW_VDD_LIMIT_OFFSET)
+	#define AVS_VDD_HIGH_LIMIT_MASK	(0x3FF << AVS_HIGH_VDD_LIMIT_OFFSET)
+#endif
+
+/* VDD limit is 0.9V for A70x0 @ CPU frequency < 1600MHz */
+#define AVS_A7K_LOW_CLK_VALUE		((0x80 << AVS_TARGET_DELTA_OFFSET) | \
+					 (0x1A << AVS_HIGH_VDD_LIMIT_OFFSET) | \
+					 (0x1A << AVS_LOW_VDD_LIMIT_OFFSET) | \
+					 (0x1 << AVS_SOFT_RESET_OFFSET) | \
+					 (0x1 << AVS_ENABLE_OFFSET))
+/* VDD limit is 1.0V for all A80x0 devices */
+#define AVS_A8K_CLK_VALUE		((0x80 << AVS_TARGET_DELTA_OFFSET) | \
+					 (0x24 << AVS_HIGH_VDD_LIMIT_OFFSET) | \
+					 (0x24 << AVS_LOW_VDD_LIMIT_OFFSET) | \
+					 (0x1 << AVS_SOFT_RESET_OFFSET) | \
+					 (0x1 << AVS_ENABLE_OFFSET))
+
+/* VDD is 0.88V for 2GHz clock on CN913x devices */
+#define AVS_AP807_CLK_VALUE		((0x80UL << 24) | \
+					 (0x2dc << 13) | \
+					 (0x2dc << 3) | \
+					 (0x1 << AVS_SOFT_RESET_OFFSET) | \
+					 (0x1 << AVS_ENABLE_OFFSET))
+
+/*
+ * - Identification information in the LD-0 eFuse:
+ *	DRO:           LD0[74:65] - Not used by the SW
+ *	Revision:      LD0[78:75] - Not used by the SW
+ *	Bin:           LD0[80:79] - Not used by the SW
+ *	SW Revision:   LD0[115:113]
+ *	Cluster 1 PWR: LD0[193] - if set to 1, power down CPU Cluster-1
+ *				  resulting in 2 CPUs active only (7020)
+ */
+/* Offsets for 2 efuse fields combined into single 64-bit value [125:63] */
+#define EFUSE_AP_LD0_DRO_OFFS		2		/* LD0[74:65] */
+#define EFUSE_AP_LD0_DRO_MASK		0x3FF
+#define EFUSE_AP_LD0_REVID_OFFS		12		/* LD0[78:75] */
+#define EFUSE_AP_LD0_REVID_MASK		0xF
+#define EFUSE_AP_LD0_BIN_OFFS		16		/* LD0[80:79] */
+#define EFUSE_AP_LD0_BIN_MASK		0x3
+#define EFUSE_AP_LD0_SWREV_MASK		0x7
+
+#ifndef MVEBU_SOC_AP807
+	/* AP806 AVS work points in the LD0 eFuse
+	 * SVC1 work point:     LD0[88:81]
+	 * SVC2 work point:     LD0[96:89]
+	 * SVC3 work point:     LD0[104:97]
+	 * SVC4 work point:     LD0[112:105]
+	 */
+	#define EFUSE_AP_LD0_SVC1_OFFS		18	/* LD0[88:81] */
+	#define EFUSE_AP_LD0_SVC2_OFFS		26	/* LD0[96:89] */
+	#define EFUSE_AP_LD0_SVC3_OFFS		34	/* LD0[104:97] */
+	#define EFUSE_AP_LD0_WP_MASK		0xFF
+	#define EFUSE_AP_LD0_SWREV_OFFS		50	/* LD0[115:113] */
+#else
+	/* AP807 AVS work points in the LD0 eFuse
+	 * SVC1 work point:     LD0[91:81]
+	 * SVC2 work point:     LD0[102:92]
+	 * SVC3 work point:     LD0[113:103]
+	 */
+	#define EFUSE_AP_LD0_SVC1_OFFS		18	/* LD0[91:81] */
+	#define EFUSE_AP_LD0_SVC2_OFFS		29	/* LD0[102:92] */
+	#define EFUSE_AP_LD0_SVC3_OFFS		40	/* LD0[113:103] */
+	#define EFUSE_AP_LD0_WP_MASK		0x7FF	/* 10 data,1 parity */
+	#define EFUSE_AP_LD0_SWREV_OFFS		51	/* LD0[116:114] */
+#endif
+
+#define EFUSE_AP_LD0_SVC4_OFFS			42	/* LD0[112:105] */
+
+#define EFUSE_AP_LD0_CLUSTER_DOWN_OFFS		4
+
+#if MARVELL_SVC_TEST
+#define MVEBU_CP_MPP_CTRL37_OFFS	20
+#define MVEBU_CP_MPP_CTRL38_OFFS	24
+#define MVEBU_CP_MPP_I2C_FUNC		2
+#define MVEBU_MPP_CTRL_MASK		0xf
+#endif
+
+/* Return the AP revision of the chip */
+static unsigned int ble_get_ap_type(void)
+{
+	unsigned int chip_rev_id;
+
+	chip_rev_id = mmio_read_32(MVEBU_CSS_GWD_CTRL_IIDR2_REG);
+	chip_rev_id = ((chip_rev_id & GWD_IIDR2_CHIP_ID_MASK) >>
+			GWD_IIDR2_CHIP_ID_OFFSET);
+
+	return chip_rev_id;
+}
+
+/******************************************************************************
+ * The routine allows to save the CCU and IO windows configuration during DRAM
+ * setup and restore them afterwards before exiting the BLE stage.
+ * Such window configuration is required since not all default settings coming
+ * from the HW and the BootROM allow access to peripherals connected to
+ * all available CPn components.
+ * For instance, when the boot device is located on CP0, the IO window to CP1
+ * is not opened automatically by the HW and if the DRAM SPD is located on CP1
+ * i2c channel, it cannot be read at BLE stage.
+ * Therefore the DRAM init procedure have to provide access to all available
+ * CPn peripherals during the BLE stage by setting the CCU IO window to all
+ * CPnph addresses and by enabling the IO windows accordingly.
+ * Additionally this function configures the CCU GCR to DRAM, which allows
+ * usage or more than 4GB DRAM as it configured by the default CCU DRAM window.
+ *
+ * IN:
+ *	MMAP_SAVE_AND_CONFIG	- save the existing configuration and update it
+ *	MMAP_RESTORE_SAVED	- restore saved configuration
+ * OUT:
+ *	NONE
+ ****************************************************************************
+ */
+static void ble_plat_mmap_config(int restore)
+{
+	if (restore == MMAP_RESTORE_SAVED) {
+		/* Restore all orig. settings that were modified by BLE stage */
+		ccu_restore_win_all(MVEBU_AP0);
+		/* Restore CCU */
+		iow_restore_win_all(MVEBU_AP0);
+		return;
+	}
+
+	/* Store original values */
+	ccu_save_win_all(MVEBU_AP0);
+	/* Save CCU */
+	iow_save_win_all(MVEBU_AP0);
+
+	init_ccu(MVEBU_AP0);
+	/* The configuration saved, now all the changes can be done */
+	init_io_win(MVEBU_AP0);
+}
+
+/****************************************************************************
+ * Setup Adaptive Voltage Switching - this is required for some platforms
+ ****************************************************************************
+ */
+#if !MARVELL_SVC_TEST
+static void ble_plat_avs_config(void)
+{
+	uint32_t freq_mode, device_id;
+	uint32_t avs_val = 0;
+
+	freq_mode =
+		SAR_CLOCK_FREQ_MODE(mmio_read_32(MVEBU_AP_SAR_REG_BASE(
+						 FREQ_MODE_AP_SAR_REG_NUM)));
+	/* Check which SoC is running and act accordingly */
+	if (ble_get_ap_type() == CHIP_ID_AP807) {
+
+		avs_val = AVS_AP807_CLK_VALUE;
+
+	} else {
+		/* Check which SoC is running and act accordingly */
+		device_id = cp110_device_id_get(MVEBU_CP_REGS_BASE(0));
+		switch (device_id) {
+		case MVEBU_80X0_DEV_ID:
+		case MVEBU_80X0_CP115_DEV_ID:
+			/* Always fix the default AVS value on A80x0 */
+			avs_val = AVS_A8K_CLK_VALUE;
+			break;
+		case MVEBU_70X0_DEV_ID:
+		case MVEBU_70X0_CP115_DEV_ID:
+			/* Fix AVS for CPU clocks lower than 1600MHz on A70x0 */
+			if ((freq_mode > CPU_1600_DDR_900_RCLK_900_2) &&
+			    (freq_mode < CPU_DDR_RCLK_INVALID))
+				avs_val = AVS_A7K_LOW_CLK_VALUE;
+			break;
+		default:
+			ERROR("Unsupported Device ID 0x%x\n", device_id);
+			return;
+		}
+	}
+
+	if (avs_val) {
+		VERBOSE("AVS: Setting AVS CTRL to 0x%x\n", avs_val);
+		mmio_write_32(AVS_EN_CTRL_REG, avs_val);
+	}
+}
+#endif
+/******************************************************************************
+ * Update or override current AVS work point value using data stored in EEPROM
+ * This is only required by QA/validation flows and activated by
+ * MARVELL_SVC_TEST flag.
+ *
+ * The function is expected to be called twice.
+ *
+ * First time with AVS value of 0 for testing if the EEPROM requests completely
+ * override the AVS value and bypass the eFuse test
+ *
+ * Second time - with non-zero AVS value obtained from eFuses as an input.
+ * In this case the EEPROM may contain AVS correction value (either positive
+ * or negative) that is added to the input AVS value and returned back for
+ * further processing.
+ ******************************************************************************
+ */
+static uint32_t avs_update_from_eeprom(uint32_t avs_workpoint)
+{
+	uint32_t new_wp = avs_workpoint;
+#if MARVELL_SVC_TEST
+	/* ---------------------------------------------------------------------
+	 * EEPROM  |  Data description (avs_step)
+	 * address |
+	 * ---------------------------------------------------------------------
+	 * 0x120   | AVS workpoint correction value
+	 *         | if not 0 and not 0xff, correct the AVS taken from eFuse
+	 *         | by the number of steps indicated by bit[6:0]
+	 *         | bit[7] defines correction direction.
+	 *         | If bit[7]=1, add the value from bit[6:0] to AVS workpoint,
+	 *         | othervise substruct this value from AVS workpoint.
+	 * ---------------------------------------------------------------------
+	 * 0x121   | AVS workpoint override value
+	 *         | Override the AVS workpoint with the value stored in this
+	 *         | byte. When running on AP806, the AVS workpoint is 7 bits
+	 *         | wide and override value is valid when bit[6:0] holds
+	 *         | value greater than zero and smaller than 0x33.
+	 *         | When running on AP807, the AVS workpoint is 10 bits wide.
+	 *         | Additional 2 MSB bits are supplied by EEPROM byte 0x122.
+	 *         | AVS override value is valid when byte @ 0x121 and bit[1:0]
+	 *         | of byte @ 0x122 combined have non-zero value.
+	 * ---------------------------------------------------------------------
+	 * 0x122   | Extended AVS workpoint override value
+	 *         | Valid only for AP807 platforms and must be less than 0x4
+	 * ---------------------------------------------------------------------
+	 */
+	static uint8_t  avs_step[3] = {0};
+	uintptr_t reg;
+	uint32_t val;
+	unsigned int ap_type = ble_get_ap_type();
+
+	/* Always happens on second call to this function */
+	if (avs_workpoint != 0) {
+		/* Get correction steps from the EEPROM */
+		if ((avs_step[0] != 0) && (avs_step[0] != 0xff)) {
+			NOTICE("AVS request to step %s by 0x%x from old 0x%x\n",
+				avs_step[0] & 0x80 ? "DOWN" : "UP",
+				avs_step[0] & 0x7f, new_wp);
+			if (avs_step[0] & 0x80)
+				new_wp -= avs_step[0] & 0x7f;
+			else
+				new_wp += avs_step[0] & 0x7f;
+		}
+
+		return new_wp;
+	}
+
+	/* AVS values are located in EEPROM
+	 * at CP0 i2c bus #0, device 0x57 offset 0x120
+	 * The SDA and SCK pins of CP0 i2c-0: MPP[38:37], i2c function 0x2.
+	 */
+	reg = MVEBU_CP_MPP_REGS(0, 4);
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
+		 (MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
+	val |= (MVEBU_CP_MPP_I2C_FUNC << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_CP_MPP_I2C_FUNC << MVEBU_CP_MPP_CTRL38_OFFS);
+	mmio_write_32(reg, val);
+
+	/* Init CP0 i2c-0 */
+	i2c_init((void *)(MVEBU_CP0_I2C_BASE));
+
+	/* Read EEPROM only once at the fist call! */
+	i2c_read(AVS_I2C_EEPROM_ADDR, 0x120, 2, avs_step, 3);
+	NOTICE("== SVC test build ==\n");
+	NOTICE("EEPROM holds values 0x%x, 0x%x and 0x%x\n",
+		avs_step[0], avs_step[1], avs_step[2]);
+
+	/* Override the AVS value? */
+	if ((ap_type != CHIP_ID_AP807) && (avs_step[1] < 0x33)) {
+		/* AP806 - AVS is 7 bits */
+		new_wp = avs_step[1];
+
+	} else if (ap_type == CHIP_ID_AP807 && (avs_step[2] < 0x4)) {
+		/* AP807 - AVS is 10 bits */
+		new_wp = avs_step[2];
+		new_wp <<= 8;
+		new_wp |= avs_step[1];
+	}
+
+	if (new_wp == 0)
+		NOTICE("Ignore BAD AVS Override value in EEPROM!\n");
+	else
+		NOTICE("Override AVS by EEPROM value 0x%x\n", new_wp);
+#endif /* MARVELL_SVC_TEST */
+	return new_wp;
+}
+
+/****************************************************************************
+ * SVC flow - v0.10
+ * The feature is intended to configure AVS value according to eFuse values
+ * that are burned individually for each SoC during the test process.
+ * Primary AVS value is stored in HD efuse and processed on power on
+ * by the HW engine
+ * Secondary AVS value is located in LD efuse and contains 4 work points for
+ * various CPU frequencies.
+ * The Secondary AVS value is only taken into account if the SW Revision stored
+ * in the efuse is greater than 0 and the CPU is running in a certain speed.
+ ****************************************************************************
+ */
+static void ble_plat_svc_config(void)
+{
+	uint32_t reg_val, avs_workpoint, freq_pidi_mode;
+	uint64_t efuse;
+	uint32_t device_id, single_cluster;
+	uint16_t  svc[4], perr[4], i, sw_ver;
+	uint8_t	 avs_data_bits, min_sw_ver, svc_fields;
+	unsigned int ap_type;
+
+	/* Get test EERPOM data */
+	avs_workpoint = avs_update_from_eeprom(0);
+	if (avs_workpoint)
+		goto set_aws_wp;
+
+	/* Set access to LD0 */
+	reg_val = mmio_read_32(MVEBU_AP_EFUSE_SRV_CTRL_REG);
+	reg_val &= ~EFUSE_SRV_CTRL_LD_SELECT_MASK;
+	mmio_write_32(MVEBU_AP_EFUSE_SRV_CTRL_REG, reg_val);
+
+	/* Obtain the value of LD0[125:63] */
+	efuse = mmio_read_32(MVEBU_AP_LDX_125_95_EFUSE_OFFS);
+	efuse <<= 32;
+	efuse |= mmio_read_32(MVEBU_AP_LDX_94_63_EFUSE_OFFS);
+
+	/* SW Revision:
+	 * Starting from SW revision 1 the SVC flow is supported.
+	 * SW version 0 (efuse not programmed) should follow the
+	 * regular AVS update flow.
+	 */
+	sw_ver = (efuse >> EFUSE_AP_LD0_SWREV_OFFS) & EFUSE_AP_LD0_SWREV_MASK;
+	if (sw_ver < 1) {
+		NOTICE("SVC: SW Revision 0x%x. SVC is not supported\n", sw_ver);
+#if MARVELL_SVC_TEST
+		NOTICE("SVC_TEST: AVS bypassed\n");
+
+#else
+		ble_plat_avs_config();
+#endif
+		return;
+	}
+
+	/* Frequency mode from SAR */
+	freq_pidi_mode = SAR_CLOCK_FREQ_MODE(
+				mmio_read_32(
+					MVEBU_AP_SAR_REG_BASE(
+						FREQ_MODE_AP_SAR_REG_NUM)));
+
+	/* Decode all SVC work points */
+	svc[0] = (efuse >> EFUSE_AP_LD0_SVC1_OFFS) & EFUSE_AP_LD0_WP_MASK;
+	svc[1] = (efuse >> EFUSE_AP_LD0_SVC2_OFFS) & EFUSE_AP_LD0_WP_MASK;
+	svc[2] = (efuse >> EFUSE_AP_LD0_SVC3_OFFS) & EFUSE_AP_LD0_WP_MASK;
+
+	/* Fetch AP type to distinguish between AP806 and AP807 */
+	ap_type = ble_get_ap_type();
+
+	if (ap_type != CHIP_ID_AP807) {
+		svc[3] = (efuse >> EFUSE_AP_LD0_SVC4_OFFS)
+			 & EFUSE_AP_LD0_WP_MASK;
+		INFO("SVC: Efuse WP: [0]=0x%x, [1]=0x%x, [2]=0x%x, [3]=0x%x\n",
+		     svc[0], svc[1], svc[2], svc[3]);
+		avs_data_bits = 7;
+		min_sw_ver = 2; /* parity check from sw revision 2 */
+		svc_fields = 4;
+	} else {
+		INFO("SVC: Efuse WP: [0]=0x%x, [1]=0x%x, [2]=0x%x\n",
+		     svc[0], svc[1], svc[2]);
+		avs_data_bits = 10;
+		min_sw_ver = 1; /* parity check required from sw revision 1 */
+		svc_fields = 3;
+	}
+
+	/* Validate parity of SVC workpoint values */
+	for (i = 0; i < svc_fields; i++) {
+		uint8_t parity, bit;
+		perr[i] = 0;
+
+		for (bit = 1, parity = (svc[i] & 1); bit < avs_data_bits; bit++)
+			parity ^= (svc[i] >> bit) & 1;
+
+		/* From SW version 1 or 2 (AP806/AP807), check parity */
+		if ((sw_ver >= min_sw_ver) &&
+		    (parity != ((svc[i] >> avs_data_bits) & 1)))
+			perr[i] = 1; /* register the error */
+	}
+
+	single_cluster = mmio_read_32(MVEBU_AP_LDX_220_189_EFUSE_OFFS);
+	single_cluster = (single_cluster >> EFUSE_AP_LD0_CLUSTER_DOWN_OFFS) & 1;
+
+	device_id = cp110_device_id_get(MVEBU_CP_REGS_BASE(0));
+	if (device_id == MVEBU_80X0_DEV_ID ||
+	    device_id == MVEBU_80X0_CP115_DEV_ID) {
+		/* A8040/A8020 */
+		NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n",
+			single_cluster == 0 ? "8040" : "8020", freq_pidi_mode);
+		switch (freq_pidi_mode) {
+		case CPU_1800_DDR_1050_RCLK_1050:
+			if (perr[1])
+				goto perror;
+			avs_workpoint = svc[1];
+			break;
+		case CPU_1600_DDR_1050_RCLK_1050:
+		case CPU_1600_DDR_900_RCLK_900_2:
+			if (perr[2])
+				goto perror;
+			avs_workpoint = svc[2];
+			break;
+		case CPU_1300_DDR_800_RCLK_800:
+		case CPU_1300_DDR_650_RCLK_650:
+			if (perr[3])
+				goto perror;
+			avs_workpoint = svc[3];
+			break;
+		case CPU_2000_DDR_1200_RCLK_1200:
+		case CPU_2000_DDR_1050_RCLK_1050:
+		default:
+			if (perr[0])
+				goto perror;
+			avs_workpoint = svc[0];
+			break;
+		}
+	} else if (device_id == MVEBU_70X0_DEV_ID ||
+		   device_id == MVEBU_70X0_CP115_DEV_ID) {
+		/* A7040/A7020/A6040 */
+		NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n",
+			single_cluster == 0 ? "7040" : "7020", freq_pidi_mode);
+		switch (freq_pidi_mode) {
+		case CPU_1400_DDR_800_RCLK_800:
+			if (single_cluster) {/* 7020 */
+				if (perr[1])
+					goto perror;
+				avs_workpoint = svc[1];
+			} else {
+				if (perr[0])
+					goto perror;
+				avs_workpoint = svc[0];
+			}
+			break;
+		case CPU_1200_DDR_800_RCLK_800:
+			if (single_cluster) {/* 7020 */
+				if (perr[2])
+					goto perror;
+				avs_workpoint = svc[2];
+			} else {
+				if (perr[1])
+					goto perror;
+				avs_workpoint = svc[1];
+			}
+			break;
+		case CPU_800_DDR_800_RCLK_800:
+		case CPU_1000_DDR_800_RCLK_800:
+			if (single_cluster) {/* 7020 */
+				if (perr[3])
+					goto perror;
+				avs_workpoint = svc[3];
+			} else {
+				if (perr[2])
+					goto perror;
+				avs_workpoint = svc[2];
+			}
+			break;
+		case CPU_600_DDR_800_RCLK_800:
+			if (perr[3])
+				goto perror;
+			avs_workpoint = svc[3]; /* Same for 6040 and 7020 */
+			break;
+		case CPU_1600_DDR_800_RCLK_800: /* 7020 only */
+		default:
+			if (single_cluster) {/* 7020 */
+				if (perr[0])
+					goto perror;
+				avs_workpoint = svc[0];
+			} else {
+#if MARVELL_SVC_TEST
+				reg_val = mmio_read_32(AVS_EN_CTRL_REG);
+				avs_workpoint = (reg_val &
+					AVS_VDD_LOW_LIMIT_MASK) >>
+					AVS_LOW_VDD_LIMIT_OFFSET;
+				NOTICE("7040 1600Mhz, avs = 0x%x\n",
+					avs_workpoint);
+#else
+				NOTICE("SVC: AVS work point not changed\n");
+				return;
+#endif
+			}
+			break;
+		}
+	} else if (device_id == MVEBU_3900_DEV_ID) {
+		NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n",
+		       "3900", freq_pidi_mode);
+		switch (freq_pidi_mode) {
+		case CPU_1600_DDR_1200_RCLK_1200:
+			if (perr[0])
+				goto perror;
+			avs_workpoint = svc[0];
+			break;
+		case CPU_1300_DDR_800_RCLK_800:
+			if (perr[1])
+				goto perror;
+			avs_workpoint = svc[1];
+			break;
+		default:
+			if (perr[0])
+				goto perror;
+			avs_workpoint = svc[0];
+			break;
+		}
+	} else if (device_id == MVEBU_CN9130_DEV_ID) {
+		NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n",
+		       "CN913x", freq_pidi_mode);
+		switch (freq_pidi_mode) {
+		case CPU_2200_DDR_1200_RCLK_1200:
+			if (perr[0])
+				goto perror;
+			avs_workpoint = svc[0];
+			break;
+		case CPU_2000_DDR_1200_RCLK_1200:
+			if (perr[1])
+				goto perror;
+			avs_workpoint = svc[1];
+			break;
+		case CPU_1600_DDR_1200_RCLK_1200:
+			if (perr[2])
+				goto perror;
+			avs_workpoint = svc[2];
+			break;
+		default:
+			ERROR("SVC: Unsupported Frequency 0x%x\n",
+				freq_pidi_mode);
+			return;
+
+		}
+	} else {
+		ERROR("SVC: Unsupported Device ID 0x%x\n", device_id);
+		return;
+	}
+
+	/* Set AVS control if needed */
+	if (avs_workpoint == 0) {
+		ERROR("SVC: You are using a frequency setup which is\n");
+		ERROR("Not supported by this device\n");
+		ERROR("This may result in malfunction of the device\n");
+		return;
+	}
+
+	/* Remove parity bit */
+	if (ap_type != CHIP_ID_AP807)
+		avs_workpoint &= 0x7F;
+	else
+		avs_workpoint &= 0x3FF;
+
+	/* Update WP from EEPROM if needed */
+	avs_workpoint = avs_update_from_eeprom(avs_workpoint);
+
+set_aws_wp:
+	reg_val  = mmio_read_32(AVS_EN_CTRL_REG);
+	NOTICE("SVC: AVS work point changed from 0x%x to 0x%x\n",
+		(reg_val & AVS_VDD_LOW_LIMIT_MASK) >> AVS_LOW_VDD_LIMIT_OFFSET,
+		avs_workpoint);
+	reg_val &= ~(AVS_VDD_LOW_LIMIT_MASK | AVS_VDD_HIGH_LIMIT_MASK);
+	reg_val |= 0x1 << AVS_ENABLE_OFFSET;
+	reg_val |= avs_workpoint << AVS_HIGH_VDD_LIMIT_OFFSET;
+	reg_val |= avs_workpoint << AVS_LOW_VDD_LIMIT_OFFSET;
+	mmio_write_32(AVS_EN_CTRL_REG, reg_val);
+	return;
+
+perror:
+	ERROR("Failed SVC WP[%d] parity check!\n", i);
+	ERROR("Ignoring the WP values\n");
+}
+
+#if PLAT_RECOVERY_IMAGE_ENABLE
+static int ble_skip_image_i2c(struct skip_image *skip_im)
+{
+	ERROR("skipping image using i2c is not supported\n");
+	/* not supported */
+	return 0;
+}
+
+static int ble_skip_image_other(struct skip_image *skip_im)
+{
+	ERROR("implementation missing for skip image request\n");
+	/* not supported, make your own implementation */
+	return 0;
+}
+
+static int ble_skip_image_gpio(struct skip_image *skip_im)
+{
+	unsigned int val;
+	unsigned int mpp_address = 0;
+	unsigned int offset = 0;
+
+	switch (skip_im->info.test.cp_ap) {
+	case(CP):
+		mpp_address = MVEBU_CP_GPIO_DATA_IN(skip_im->info.test.cp_index,
+						    skip_im->info.gpio.num);
+		if (skip_im->info.gpio.num > NUM_OF_GPIO_PER_REG)
+			offset = skip_im->info.gpio.num - NUM_OF_GPIO_PER_REG;
+		else
+			offset = skip_im->info.gpio.num;
+		break;
+	case(AP):
+		mpp_address = MVEBU_AP_GPIO_DATA_IN;
+		offset = skip_im->info.gpio.num;
+		break;
+	}
+
+	val = mmio_read_32(mpp_address);
+	val &= (1 << offset);
+	if ((!val && skip_im->info.gpio.button_state == HIGH) ||
+	    (val && skip_im->info.gpio.button_state == LOW)) {
+		mmio_write_32(SCRATCH_PAD_REG2, SCRATCH_PAD_SKIP_VAL);
+		return 1;
+	}
+
+	return 0;
+}
+
+/*
+ * This function checks if there's a skip image request:
+ * return values:
+ * 1: (true) images request been made.
+ * 0: (false) no image request been made.
+ */
+static int  ble_skip_current_image(void)
+{
+	struct skip_image *skip_im;
+
+	/*fetching skip image info*/
+	skip_im = (struct skip_image *)plat_marvell_get_skip_image_data();
+
+	if (skip_im == NULL)
+		return 0;
+
+	/* check if skipping image request has already been made */
+	if (mmio_read_32(SCRATCH_PAD_REG2) == SCRATCH_PAD_SKIP_VAL)
+		return 0;
+
+	switch (skip_im->detection_method) {
+	case GPIO:
+		return ble_skip_image_gpio(skip_im);
+	case I2C:
+		return ble_skip_image_i2c(skip_im);
+	case USER_DEFINED:
+		return ble_skip_image_other(skip_im);
+	}
+
+	return 0;
+}
+#endif
+
+
+int ble_plat_setup(int *skip)
+{
+	int ret, cp;
+	unsigned int freq_mode;
+
+	/* Power down unused CPUs */
+	plat_marvell_early_cpu_powerdown();
+
+	/*
+	 * Save the current CCU configuration and make required changes:
+	 * - Allow access to DRAM larger than 4GB
+	 * - Open memory access to all CPn peripherals
+	 */
+	ble_plat_mmap_config(MMAP_SAVE_AND_CONFIG);
+
+#if PLAT_RECOVERY_IMAGE_ENABLE
+	/* Check if there's a skip request to bootRom recovery Image */
+	if (ble_skip_current_image()) {
+		/* close memory access to all CPn peripherals. */
+		ble_plat_mmap_config(MMAP_RESTORE_SAVED);
+		*skip = 1;
+		return 0;
+	}
+#endif
+	/* Do required CP-110 setups for BLE stage */
+	cp110_ble_init(MVEBU_CP_REGS_BASE(0));
+
+	/* Config address for each cp other than cp0 */
+	for (cp = 1; cp < CP_COUNT; cp++)
+		update_cp110_default_win(cp);
+
+	/* Setup AVS */
+	ble_plat_svc_config();
+
+	/* read clk option from sampled-at-reset register */
+	freq_mode =
+		SAR_CLOCK_FREQ_MODE(mmio_read_32(MVEBU_AP_SAR_REG_BASE(
+						 FREQ_MODE_AP_SAR_REG_NUM)));
+
+	/* work with PLL clock driver in AP807 */
+	if (ble_get_ap_type() == CHIP_ID_AP807)
+		ap807_clocks_init(freq_mode);
+
+	/* Do required AP setups for BLE stage */
+	ap_ble_init();
+
+	/* Update DRAM topology (scan DIMM SPDs) */
+	plat_marvell_dram_update_topology();
+
+	/* Kick it in */
+	ret = dram_init();
+
+	/* Restore the original CCU configuration before exit from BLE */
+	ble_plat_mmap_config(MMAP_RESTORE_SAVED);
+
+	return ret;
+}
diff --git a/plat/marvell/armada/a8k/common/plat_pm.c b/plat/marvell/armada/a8k/common/plat_pm.c
new file mode 100644
index 0000000..f08f08a
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/plat_pm.c
@@ -0,0 +1,853 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+
+#include <common/debug.h>
+#include <drivers/arm/gicv2.h>
+#include <drivers/console.h>
+#include <drivers/delay_timer.h>
+#include <drivers/marvell/cache_llc.h>
+#include <lib/bakery_lock.h>
+#include <lib/mmio.h>
+#include <plat/common/platform.h>
+
+#include <armada_common.h>
+#include <marvell_pm.h>
+#if MSS_SUPPORT
+#include <mss_pm_ipc.h>
+#endif
+#include <plat_marvell.h>
+#include <plat_pm_trace.h>
+
+#define MVEBU_PRIVATE_UID_REG		0x30
+#define MVEBU_RFU_GLOBL_SW_RST		0x84
+#define MVEBU_CCU_RVBAR(cpu)		(MVEBU_REGS_BASE + 0x640 + (cpu * 4))
+#define MVEBU_CCU_CPU_UN_RESET(cpu)	(MVEBU_REGS_BASE + 0x650 + (cpu * 4))
+
+#define MPIDR_CPU_GET(mpidr)		((mpidr) & MPIDR_CPU_MASK)
+#define MPIDR_CLUSTER_GET(mpidr)	MPIDR_AFFLVL1_VAL((mpidr))
+
+#define MVEBU_GPIO_MASK(index)		(1 << (index % 32))
+#define MVEBU_MPP_MASK(index)		(0xF << (4 * (index % 8)))
+#define MVEBU_GPIO_VALUE(index, value)	(value << (index % 32))
+
+#define MVEBU_USER_CMD_0_REG		(MVEBU_DRAM_MAC_BASE + 0x20)
+#define MVEBU_USER_CMD_CH0_OFFSET	28
+#define MVEBU_USER_CMD_CH0_MASK		(1 << MVEBU_USER_CMD_CH0_OFFSET)
+#define MVEBU_USER_CMD_CH0_EN		(1 << MVEBU_USER_CMD_CH0_OFFSET)
+#define MVEBU_USER_CMD_CS_OFFSET	24
+#define MVEBU_USER_CMD_CS_MASK		(0xF << MVEBU_USER_CMD_CS_OFFSET)
+#define MVEBU_USER_CMD_CS_ALL		(0xF << MVEBU_USER_CMD_CS_OFFSET)
+#define MVEBU_USER_CMD_SR_OFFSET	6
+#define MVEBU_USER_CMD_SR_MASK		(0x3 << MVEBU_USER_CMD_SR_OFFSET)
+#define MVEBU_USER_CMD_SR_ENTER		(0x1 << MVEBU_USER_CMD_SR_OFFSET)
+#define MVEBU_MC_PWR_CTRL_REG		(MVEBU_DRAM_MAC_BASE + 0x54)
+#define MVEBU_MC_AC_ON_DLY_OFFSET	8
+#define MVEBU_MC_AC_ON_DLY_MASK		(0xF << MVEBU_MC_AC_ON_DLY_OFFSET)
+#define MVEBU_MC_AC_ON_DLY_DEF_VAR	(8 << MVEBU_MC_AC_ON_DLY_OFFSET)
+#define MVEBU_MC_AC_OFF_DLY_OFFSET	4
+#define MVEBU_MC_AC_OFF_DLY_MASK	(0xF << MVEBU_MC_AC_OFF_DLY_OFFSET)
+#define MVEBU_MC_AC_OFF_DLY_DEF_VAR	(0xC << MVEBU_MC_AC_OFF_DLY_OFFSET)
+#define MVEBU_MC_PHY_AUTO_OFF_OFFSET	0
+#define MVEBU_MC_PHY_AUTO_OFF_MASK	(1 << MVEBU_MC_PHY_AUTO_OFF_OFFSET)
+#define MVEBU_MC_PHY_AUTO_OFF_EN	(1 << MVEBU_MC_PHY_AUTO_OFF_OFFSET)
+
+/* this lock synchronize AP multiple cores execution with MSS */
+DEFINE_BAKERY_LOCK(pm_sys_lock);
+
+/* Weak definitions may be overridden in specific board */
+#pragma weak plat_marvell_get_pm_cfg
+
+/* AP806 CPU power down /power up definitions */
+enum CPU_ID {
+	CPU0,
+	CPU1,
+	CPU2,
+	CPU3
+};
+
+#define REG_WR_VALIDATE_TIMEOUT		(2000)
+
+#define FEATURE_DISABLE_STATUS_REG			\
+			(MVEBU_REGS_BASE + 0x6F8230)
+#define FEATURE_DISABLE_STATUS_CPU_CLUSTER_OFFSET	4
+#define FEATURE_DISABLE_STATUS_CPU_CLUSTER_MASK		\
+			(0x1 << FEATURE_DISABLE_STATUS_CPU_CLUSTER_OFFSET)
+
+#ifdef MVEBU_SOC_AP807
+	#define PWRC_CPUN_CR_PWR_DN_RQ_OFFSET		1
+	#define PWRC_CPUN_CR_LDO_BYPASS_RDY_OFFSET	0
+#else
+	#define PWRC_CPUN_CR_PWR_DN_RQ_OFFSET		0
+	#define PWRC_CPUN_CR_LDO_BYPASS_RDY_OFFSET	31
+#endif
+
+#define PWRC_CPUN_CR_REG(cpu_id)		\
+			(MVEBU_REGS_BASE + 0x680000 + (cpu_id * 0x10))
+#define PWRC_CPUN_CR_PWR_DN_RQ_MASK		\
+			(0x1 << PWRC_CPUN_CR_PWR_DN_RQ_OFFSET)
+#define PWRC_CPUN_CR_ISO_ENABLE_OFFSET		16
+#define PWRC_CPUN_CR_ISO_ENABLE_MASK		\
+			(0x1 << PWRC_CPUN_CR_ISO_ENABLE_OFFSET)
+#define PWRC_CPUN_CR_LDO_BYPASS_RDY_MASK	\
+			(0x1U << PWRC_CPUN_CR_LDO_BYPASS_RDY_OFFSET)
+
+#define CCU_B_PRCRN_REG(cpu_id)			\
+			(MVEBU_REGS_BASE + 0x1A50 + \
+			((cpu_id / 2) * (0x400)) + ((cpu_id % 2) * 4))
+#define CCU_B_PRCRN_CPUPORESET_STATIC_OFFSET	0
+#define CCU_B_PRCRN_CPUPORESET_STATIC_MASK	\
+			(0x1 << CCU_B_PRCRN_CPUPORESET_STATIC_OFFSET)
+
+/* power switch fingers */
+#define AP807_PWRC_LDO_CR0_REG			\
+			(MVEBU_REGS_BASE + 0x680000 + 0x100)
+#define AP807_PWRC_LDO_CR0_OFFSET		16
+#define AP807_PWRC_LDO_CR0_MASK			\
+			(0xff << AP807_PWRC_LDO_CR0_OFFSET)
+#define AP807_PWRC_LDO_CR0_VAL			0xfc
+
+/*
+ * Power down CPU:
+ * Used to reduce power consumption, and avoid SoC unnecessary temperature rise.
+ */
+static int plat_marvell_cpu_powerdown(int cpu_id)
+{
+	uint32_t	reg_val;
+	int		exit_loop = REG_WR_VALIDATE_TIMEOUT;
+
+	INFO("Powering down CPU%d\n", cpu_id);
+
+	/* 1. Isolation enable */
+	reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+	reg_val |= 0x1 << PWRC_CPUN_CR_ISO_ENABLE_OFFSET;
+	mmio_write_32(PWRC_CPUN_CR_REG(cpu_id), reg_val);
+
+	/* 2. Read and check Isolation enabled - verify bit set to 1 */
+	do {
+		reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+		exit_loop--;
+	} while (!(reg_val & (0x1 << PWRC_CPUN_CR_ISO_ENABLE_OFFSET)) &&
+		 exit_loop > 0);
+
+	/* 3. Switch off CPU power */
+	reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+	reg_val &= ~PWRC_CPUN_CR_PWR_DN_RQ_MASK;
+	mmio_write_32(PWRC_CPUN_CR_REG(cpu_id), reg_val);
+
+	/* 4. Read and check Switch Off - verify bit set to 0 */
+	exit_loop = REG_WR_VALIDATE_TIMEOUT;
+	do {
+		reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+		exit_loop--;
+	} while (reg_val & PWRC_CPUN_CR_PWR_DN_RQ_MASK && exit_loop > 0);
+
+	if (exit_loop <= 0)
+		goto cpu_poweroff_error;
+
+	/* 5. De-Assert power ready */
+	reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+	reg_val &= ~PWRC_CPUN_CR_LDO_BYPASS_RDY_MASK;
+	mmio_write_32(PWRC_CPUN_CR_REG(cpu_id), reg_val);
+
+	/* 6. Assert CPU POR reset */
+	reg_val = mmio_read_32(CCU_B_PRCRN_REG(cpu_id));
+	reg_val &= ~CCU_B_PRCRN_CPUPORESET_STATIC_MASK;
+	mmio_write_32(CCU_B_PRCRN_REG(cpu_id), reg_val);
+
+	/* 7. Read and poll on Validate the CPU is out of reset */
+	exit_loop = REG_WR_VALIDATE_TIMEOUT;
+	do {
+		reg_val = mmio_read_32(CCU_B_PRCRN_REG(cpu_id));
+		exit_loop--;
+	} while (reg_val & CCU_B_PRCRN_CPUPORESET_STATIC_MASK && exit_loop > 0);
+
+	if (exit_loop <= 0)
+		goto cpu_poweroff_error;
+
+	INFO("Successfully powered down CPU%d\n", cpu_id);
+
+	return 0;
+
+cpu_poweroff_error:
+	ERROR("ERROR: Can't power down CPU%d\n", cpu_id);
+	return -1;
+}
+
+/*
+ * Power down CPUs 1-3 at early boot stage,
+ * to reduce power consumption and SoC temperature.
+ * This is triggered by BLE prior to DDR initialization.
+ *
+ * Note:
+ * All CPUs will be powered up by plat_marvell_cpu_powerup on Linux boot stage,
+ * which is triggered by PSCI ops (pwr_domain_on).
+ */
+int plat_marvell_early_cpu_powerdown(void)
+{
+	uint32_t cpu_cluster_status =
+		mmio_read_32(FEATURE_DISABLE_STATUS_REG) &
+			     FEATURE_DISABLE_STATUS_CPU_CLUSTER_MASK;
+	/* if cpu_cluster_status bit is set,
+	 * that means we have only single cluster
+	 */
+	int cluster_count = cpu_cluster_status ? 1 : 2;
+
+	INFO("Powering off unused CPUs\n");
+
+	/* CPU1 is in AP806 cluster-0, which always exists, so power it down */
+	if (plat_marvell_cpu_powerdown(CPU1) == -1)
+		return -1;
+
+	/*
+	 * CPU2-3 are in AP806 2nd cluster (cluster-1),
+	 * which doesn't exists in dual-core systems.
+	 * so need to check if we have dual-core (single cluster)
+	 * or quad-code (2 clusters)
+	 */
+	if (cluster_count == 2) {
+		/* CPU2-3 are part of 2nd cluster */
+		if (plat_marvell_cpu_powerdown(CPU2) == -1)
+			return -1;
+		if (plat_marvell_cpu_powerdown(CPU3) == -1)
+			return -1;
+	}
+
+	return 0;
+}
+
+/*
+ * Power up CPU - part of Linux boot stage
+ */
+static int plat_marvell_cpu_powerup(u_register_t mpidr)
+{
+	uint32_t	reg_val;
+	int	cpu_id = MPIDR_CPU_GET(mpidr),
+		cluster = MPIDR_CLUSTER_GET(mpidr);
+	int	exit_loop = REG_WR_VALIDATE_TIMEOUT;
+
+	/* calculate absolute CPU ID */
+	cpu_id = cluster * PLAT_MARVELL_CLUSTER_CORE_COUNT + cpu_id;
+
+	INFO("Powering on CPU%d\n", cpu_id);
+
+#ifdef MVEBU_SOC_AP807
+	/* Activate 2 power switch fingers */
+	reg_val = mmio_read_32(AP807_PWRC_LDO_CR0_REG);
+	reg_val &= ~(AP807_PWRC_LDO_CR0_MASK);
+	reg_val |= (AP807_PWRC_LDO_CR0_VAL << AP807_PWRC_LDO_CR0_OFFSET);
+	mmio_write_32(AP807_PWRC_LDO_CR0_REG, reg_val);
+	udelay(100);
+#endif
+
+	/* 1. Switch CPU power ON */
+	reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+	reg_val |= 0x1 << PWRC_CPUN_CR_PWR_DN_RQ_OFFSET;
+	mmio_write_32(PWRC_CPUN_CR_REG(cpu_id), reg_val);
+
+	/* 2. Wait for CPU on, up to 100 uSec: */
+	udelay(100);
+
+	/* 3. Assert power ready */
+	reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+	reg_val |= 0x1U << PWRC_CPUN_CR_LDO_BYPASS_RDY_OFFSET;
+	mmio_write_32(PWRC_CPUN_CR_REG(cpu_id), reg_val);
+
+	/* 4. Read & Validate power ready
+	 * used in order to generate 16 Host CPU cycles
+	 */
+	do {
+		reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+		exit_loop--;
+	} while (!(reg_val & (0x1U << PWRC_CPUN_CR_LDO_BYPASS_RDY_OFFSET)) &&
+		 exit_loop > 0);
+
+	if (exit_loop <= 0)
+		goto cpu_poweron_error;
+
+	/* 5. Isolation disable */
+	reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+	reg_val &= ~PWRC_CPUN_CR_ISO_ENABLE_MASK;
+	mmio_write_32(PWRC_CPUN_CR_REG(cpu_id), reg_val);
+
+	/* 6. Read and check Isolation enabled - verify bit set to 1 */
+	exit_loop = REG_WR_VALIDATE_TIMEOUT;
+	do {
+		reg_val = mmio_read_32(PWRC_CPUN_CR_REG(cpu_id));
+		exit_loop--;
+	} while ((reg_val & (0x1 << PWRC_CPUN_CR_ISO_ENABLE_OFFSET)) &&
+		 exit_loop > 0);
+
+	/* 7. De Assert CPU POR reset & Core reset */
+	reg_val = mmio_read_32(CCU_B_PRCRN_REG(cpu_id));
+	reg_val |= 0x1 << CCU_B_PRCRN_CPUPORESET_STATIC_OFFSET;
+	mmio_write_32(CCU_B_PRCRN_REG(cpu_id), reg_val);
+
+	/* 8. Read & Validate CPU POR reset */
+	exit_loop = REG_WR_VALIDATE_TIMEOUT;
+	do {
+		reg_val = mmio_read_32(CCU_B_PRCRN_REG(cpu_id));
+		exit_loop--;
+	} while (!(reg_val & (0x1 << CCU_B_PRCRN_CPUPORESET_STATIC_OFFSET)) &&
+		 exit_loop > 0);
+
+	if (exit_loop <= 0)
+		goto cpu_poweron_error;
+
+	INFO("Successfully powered on CPU%d\n", cpu_id);
+
+	return 0;
+
+cpu_poweron_error:
+	ERROR("ERROR: Can't power up CPU%d\n", cpu_id);
+	return -1;
+}
+
+static int plat_marvell_cpu_on(u_register_t mpidr)
+{
+	int cpu_id;
+	int cluster;
+
+	/* Set barierr */
+	dsbsy();
+
+	/* Get cpu number - use CPU ID */
+	cpu_id =  MPIDR_CPU_GET(mpidr);
+
+	/* Get cluster number - use affinity level 1 */
+	cluster = MPIDR_CLUSTER_GET(mpidr);
+
+	/* Set CPU private UID */
+	mmio_write_32(MVEBU_REGS_BASE + MVEBU_PRIVATE_UID_REG, cluster + 0x4);
+
+	/* Set the cpu start address to BL1 entry point (align to 0x10000) */
+	mmio_write_32(MVEBU_CCU_RVBAR(cpu_id),
+		      PLAT_MARVELL_CPU_ENTRY_ADDR >> 16);
+
+	/* Get the cpu out of reset */
+	mmio_write_32(MVEBU_CCU_CPU_UN_RESET(cpu_id), 0x10001);
+
+	return 0;
+}
+
+/*****************************************************************************
+ * A8K handler called to check the validity of the power state
+ * parameter.
+ *****************************************************************************
+ */
+static int a8k_validate_power_state(unsigned int power_state,
+			    psci_power_state_t *req_state)
+{
+	int pstate = psci_get_pstate_type(power_state);
+	int pwr_lvl = psci_get_pstate_pwrlvl(power_state);
+	int i;
+
+	if (pwr_lvl > PLAT_MAX_PWR_LVL)
+		return PSCI_E_INVALID_PARAMS;
+
+	/* Sanity check the requested state */
+	if (pstate == PSTATE_TYPE_STANDBY) {
+		/*
+		 * It's possible to enter standby only on power level 0
+		 * Ignore any other power level.
+		 */
+		if (pwr_lvl != MARVELL_PWR_LVL0)
+			return PSCI_E_INVALID_PARAMS;
+
+		req_state->pwr_domain_state[MARVELL_PWR_LVL0] =
+					MARVELL_LOCAL_STATE_RET;
+	} else {
+		for (i = MARVELL_PWR_LVL0; i <= pwr_lvl; i++)
+			req_state->pwr_domain_state[i] =
+					MARVELL_LOCAL_STATE_OFF;
+	}
+
+	/*
+	 * We expect the 'state id' to be zero.
+	 */
+	if (psci_get_pstate_id(power_state))
+		return PSCI_E_INVALID_PARAMS;
+
+	return PSCI_E_SUCCESS;
+}
+
+/*****************************************************************************
+ * A8K handler called when a CPU is about to enter standby.
+ *****************************************************************************
+ */
+static void a8k_cpu_standby(plat_local_state_t cpu_state)
+{
+	if (!is_pm_fw_running()) {
+		ERROR("%s: needs to be implemented\n", __func__);
+		panic();
+	}
+}
+
+/*****************************************************************************
+ * A8K handler called when a power domain is about to be turned on. The
+ * mpidr determines the CPU to be turned on.
+ *****************************************************************************
+ */
+static int a8k_pwr_domain_on(u_register_t mpidr)
+{
+	/* Power up CPU (CPUs 1-3 are powered off at start of BLE) */
+	plat_marvell_cpu_powerup(mpidr);
+
+#if MSS_SUPPORT
+	if (is_pm_fw_running()) {
+		unsigned int target =
+				((mpidr & 0xFF) + (((mpidr >> 8) & 0xFF) * 2));
+
+		/*
+		 * pm system synchronization - used to synchronize
+		 * multiple core access to MSS
+		 */
+		bakery_lock_get(&pm_sys_lock);
+
+		/* send CPU ON IPC Message to MSS */
+		mss_pm_ipc_msg_send(target, PM_IPC_MSG_CPU_ON, 0);
+
+		/* trigger IPC message to MSS */
+		mss_pm_ipc_msg_trigger();
+
+		/* pm system synchronization */
+		bakery_lock_release(&pm_sys_lock);
+
+		/* trace message */
+		PM_TRACE(TRACE_PWR_DOMAIN_ON | target);
+	} else
+#endif
+	{
+		/* proprietary CPU ON execution flow */
+		plat_marvell_cpu_on(mpidr);
+	}
+	return 0;
+}
+
+/*****************************************************************************
+ * A8K handler called to validate the entry point.
+ *****************************************************************************
+ */
+static int a8k_validate_ns_entrypoint(uintptr_t entrypoint)
+{
+	return PSCI_E_SUCCESS;
+}
+
+/*****************************************************************************
+ * A8K handler called when a power domain is about to be turned off. The
+ * target_state encodes the power state that each level should transition to.
+ *****************************************************************************
+ */
+static void a8k_pwr_domain_off(const psci_power_state_t *target_state)
+{
+#if MSS_SUPPORT
+	if (is_pm_fw_running()) {
+		unsigned int idx = plat_my_core_pos();
+
+		/* Prevent interrupts from spuriously waking up this cpu */
+		gicv2_cpuif_disable();
+
+		/* pm system synchronization - used to synchronize multiple
+		 * core access to MSS
+		 */
+		bakery_lock_get(&pm_sys_lock);
+
+		/* send CPU OFF IPC Message to MSS */
+		mss_pm_ipc_msg_send(idx, PM_IPC_MSG_CPU_OFF, target_state);
+
+		/* trigger IPC message to MSS */
+		mss_pm_ipc_msg_trigger();
+
+		/* pm system synchronization */
+		bakery_lock_release(&pm_sys_lock);
+
+		/* trace message */
+		PM_TRACE(TRACE_PWR_DOMAIN_OFF);
+	} else {
+		INFO("%s: is not supported without SCP\n", __func__);
+	}
+#endif
+}
+
+/* Get PM config to power off the SoC */
+void *plat_marvell_get_pm_cfg(void)
+{
+	return NULL;
+}
+
+/*
+ * This function should be called on restore from
+ * "suspend to RAM" state when the execution flow
+ * has to bypass BootROM image to RAM copy and speed up
+ * the system recovery
+ *
+ */
+static void plat_marvell_exit_bootrom(void)
+{
+	marvell_exit_bootrom(PLAT_MARVELL_TRUSTED_ROM_BASE);
+}
+
+/*
+ * Prepare for the power off of the system via GPIO
+ */
+static void plat_marvell_power_off_gpio(struct power_off_method *pm_cfg,
+					register_t *gpio_addr,
+					register_t *gpio_data)
+{
+	unsigned int gpio;
+	unsigned int idx;
+	unsigned int shift;
+	unsigned int reg;
+	unsigned int addr;
+	gpio_info_t *info;
+	unsigned int tog_bits;
+
+	assert((pm_cfg->cfg.gpio.pin_count < PMIC_GPIO_MAX_NUMBER) &&
+	       (pm_cfg->cfg.gpio.step_count < PMIC_GPIO_MAX_TOGGLE_STEP));
+
+	/* Prepare GPIOs for PMIC */
+	for (gpio = 0; gpio < pm_cfg->cfg.gpio.pin_count; gpio++) {
+		info = &pm_cfg->cfg.gpio.info[gpio];
+		/* Set PMIC GPIO to output mode */
+		reg = mmio_read_32(MVEBU_CP_GPIO_DATA_OUT_EN(
+				   info->cp_index, info->gpio_index));
+		mmio_write_32(MVEBU_CP_GPIO_DATA_OUT_EN(
+			      info->cp_index, info->gpio_index),
+			      reg & ~MVEBU_GPIO_MASK(info->gpio_index));
+
+		/* Set the appropriate MPP to GPIO mode */
+		reg = mmio_read_32(MVEBU_PM_MPP_REGS(info->cp_index,
+						     info->gpio_index));
+		mmio_write_32(MVEBU_PM_MPP_REGS(info->cp_index,
+						info->gpio_index),
+			reg & ~MVEBU_MPP_MASK(info->gpio_index));
+	}
+
+	/* Wait for MPP & GPIO pre-configurations done */
+	mdelay(pm_cfg->cfg.gpio.delay_ms);
+
+	/* Toggle the GPIO values, and leave final step to be triggered
+	 * after  DDR self-refresh is enabled
+	 */
+	for (idx = 0; idx < pm_cfg->cfg.gpio.step_count; idx++) {
+		tog_bits = pm_cfg->cfg.gpio.seq[idx];
+
+		/* The GPIOs must be within same GPIO register,
+		 * thus could get the original value by first GPIO
+		 */
+		info = &pm_cfg->cfg.gpio.info[0];
+		reg = mmio_read_32(MVEBU_CP_GPIO_DATA_OUT(
+				   info->cp_index, info->gpio_index));
+		addr = MVEBU_CP_GPIO_DATA_OUT(info->cp_index, info->gpio_index);
+
+		for (gpio = 0; gpio < pm_cfg->cfg.gpio.pin_count; gpio++) {
+			shift = pm_cfg->cfg.gpio.info[gpio].gpio_index % 32;
+			if (GPIO_LOW == (tog_bits & (1 << gpio)))
+				reg &= ~(1 << shift);
+			else
+				reg |= (1 << shift);
+		}
+
+		/* Set the GPIO register, for last step just store
+		 * register address and values to system registers
+		 */
+		if (idx < pm_cfg->cfg.gpio.step_count - 1) {
+			mmio_write_32(MVEBU_CP_GPIO_DATA_OUT(
+				      info->cp_index, info->gpio_index), reg);
+			mdelay(pm_cfg->cfg.gpio.delay_ms);
+		} else {
+			/* Save GPIO register and address values for
+			 * finishing the power down operation later
+			 */
+			*gpio_addr = addr;
+			*gpio_data = reg;
+		}
+	}
+}
+
+/*
+ * Prepare for the power off of the system
+ */
+static void plat_marvell_power_off_prepare(struct power_off_method *pm_cfg,
+					   register_t *addr, register_t *data)
+{
+	switch (pm_cfg->type) {
+	case PMIC_GPIO:
+		plat_marvell_power_off_gpio(pm_cfg, addr, data);
+		break;
+	default:
+		break;
+	}
+}
+
+/*****************************************************************************
+ * A8K handler called when a power domain is about to be suspended. The
+ * target_state encodes the power state that each level should transition to.
+ *****************************************************************************
+ */
+static void a8k_pwr_domain_suspend(const psci_power_state_t *target_state)
+{
+#if MSS_SUPPORT
+	if (is_pm_fw_running()) {
+		unsigned int idx;
+
+		/* Prevent interrupts from spuriously waking up this cpu */
+		gicv2_cpuif_disable();
+
+		idx = plat_my_core_pos();
+
+		/* pm system synchronization - used to synchronize multiple
+		 * core access to MSS
+		 */
+		bakery_lock_get(&pm_sys_lock);
+
+		/* send CPU Suspend IPC Message to MSS */
+		mss_pm_ipc_msg_send(idx, PM_IPC_MSG_CPU_SUSPEND, target_state);
+
+		/* trigger IPC message to MSS */
+		mss_pm_ipc_msg_trigger();
+
+		/* pm system synchronization */
+		bakery_lock_release(&pm_sys_lock);
+
+		/* trace message */
+		PM_TRACE(TRACE_PWR_DOMAIN_SUSPEND);
+	} else
+#endif
+	{
+		uintptr_t *mailbox = (void *)PLAT_MARVELL_MAILBOX_BASE;
+
+		INFO("Suspending to RAM\n");
+
+		marvell_console_runtime_end();
+
+		/* Prevent interrupts from spuriously waking up this cpu */
+		gicv2_cpuif_disable();
+
+		mailbox[MBOX_IDX_SUSPEND_MAGIC] = MVEBU_MAILBOX_SUSPEND_STATE;
+		mailbox[MBOX_IDX_ROM_EXIT_ADDR] = (uintptr_t)&plat_marvell_exit_bootrom;
+
+#if PLAT_MARVELL_SHARED_RAM_CACHED
+		flush_dcache_range(PLAT_MARVELL_MAILBOX_BASE +
+		MBOX_IDX_SUSPEND_MAGIC * sizeof(uintptr_t),
+		2 * sizeof(uintptr_t));
+#endif
+		/* Flush and disable LLC before going off-power */
+		llc_disable(0);
+
+		isb();
+		/*
+		 * Do not halt here!
+		 * The function must return for allowing the caller function
+		 * psci_power_up_finish() to do the proper context saving and
+		 * to release the CPU lock.
+		 */
+	}
+}
+
+/*****************************************************************************
+ * A8K handler called when a power domain has just been powered on after
+ * being turned off earlier. The target_state encodes the low power state that
+ * each level has woken up from.
+ *****************************************************************************
+ */
+static void a8k_pwr_domain_on_finish(const psci_power_state_t *target_state)
+{
+	/* arch specific configuration */
+	marvell_psci_arch_init(0);
+
+	/* Interrupt initialization */
+	gicv2_pcpu_distif_init();
+	gicv2_cpuif_enable();
+
+	if (is_pm_fw_running()) {
+		/* trace message */
+		PM_TRACE(TRACE_PWR_DOMAIN_ON_FINISH);
+	}
+}
+
+/*****************************************************************************
+ * A8K handler called when a power domain has just been powered on after
+ * having been suspended earlier. The target_state encodes the low power state
+ * that each level has woken up from.
+ * TODO: At the moment we reuse the on finisher and reinitialize the secure
+ * context. Need to implement a separate suspend finisher.
+ *****************************************************************************
+ */
+static void a8k_pwr_domain_suspend_finish(
+					const psci_power_state_t *target_state)
+{
+	if (is_pm_fw_running()) {
+		/* arch specific configuration */
+		marvell_psci_arch_init(0);
+
+		/* Interrupt initialization */
+		gicv2_cpuif_enable();
+
+		/* trace message */
+		PM_TRACE(TRACE_PWR_DOMAIN_SUSPEND_FINISH);
+	} else {
+		uintptr_t *mailbox = (void *)PLAT_MARVELL_MAILBOX_BASE;
+
+		/* Only primary CPU requres platform init */
+		if (!plat_my_core_pos()) {
+			/* Initialize the console to provide
+			 * early debug support
+			 */
+			marvell_console_runtime_init();
+
+			bl31_plat_arch_setup();
+			marvell_bl31_platform_setup();
+			/*
+			 * Remove suspend to RAM marker from the mailbox
+			 * for treating a regular reset as a cold boot
+			 */
+			mailbox[MBOX_IDX_SUSPEND_MAGIC] = 0;
+			mailbox[MBOX_IDX_ROM_EXIT_ADDR] = 0;
+#if PLAT_MARVELL_SHARED_RAM_CACHED
+			flush_dcache_range(PLAT_MARVELL_MAILBOX_BASE +
+			MBOX_IDX_SUSPEND_MAGIC * sizeof(uintptr_t),
+			2 * sizeof(uintptr_t));
+#endif
+		}
+	}
+}
+
+/*****************************************************************************
+ * This handler is called by the PSCI implementation during the `SYSTEM_SUSPEND`
+ * call to get the `power_state` parameter. This allows the platform to encode
+ * the appropriate State-ID field within the `power_state` parameter which can
+ * be utilized in `pwr_domain_suspend()` to suspend to system affinity level.
+ *****************************************************************************
+ */
+static void a8k_get_sys_suspend_power_state(psci_power_state_t *req_state)
+{
+	/* lower affinities use PLAT_MAX_OFF_STATE */
+	for (int i = MPIDR_AFFLVL0; i <= PLAT_MAX_PWR_LVL; i++)
+		req_state->pwr_domain_state[i] = PLAT_MAX_OFF_STATE;
+}
+
+static void
+__dead2 a8k_pwr_domain_pwr_down_wfi(const psci_power_state_t *target_state)
+{
+	struct power_off_method *pm_cfg;
+	unsigned int srcmd;
+	unsigned int sdram_reg;
+	register_t gpio_data = 0, gpio_addr = 0;
+
+	if (is_pm_fw_running()) {
+		psci_power_down_wfi();
+		panic();
+	}
+
+	pm_cfg = (struct power_off_method *)plat_marvell_get_pm_cfg();
+
+	/* Prepare for power off */
+	plat_marvell_power_off_prepare(pm_cfg, &gpio_addr, &gpio_data);
+
+	/* First step to enable DDR self-refresh
+	 * to keep the data during suspend
+	 */
+	mmio_write_32(MVEBU_MC_PWR_CTRL_REG, 0x8C1);
+
+	/* Save DDR self-refresh second step register
+	 * and value to be issued later
+	 */
+	sdram_reg = MVEBU_USER_CMD_0_REG;
+	srcmd = mmio_read_32(sdram_reg);
+	srcmd &= ~(MVEBU_USER_CMD_CH0_MASK | MVEBU_USER_CMD_CS_MASK |
+		 MVEBU_USER_CMD_SR_MASK);
+	srcmd |= (MVEBU_USER_CMD_CH0_EN | MVEBU_USER_CMD_CS_ALL |
+		 MVEBU_USER_CMD_SR_ENTER);
+
+	/*
+	 * Wait for DRAM is done using registers access only.
+	 * At this stage any access to DRAM (procedure call) will
+	 * release it from the self-refresh mode
+	 */
+	__asm__ volatile (
+		/* Align to a cache line */
+		"	.balign 64\n\t"
+
+		/* Enter self refresh */
+		"	str %[srcmd], [%[sdram_reg]]\n\t"
+
+		/*
+		 * Wait 100 cycles for DDR to enter self refresh, by
+		 * doing 50 times two instructions.
+		 */
+		"	mov x1, #50\n\t"
+		"1:	subs x1, x1, #1\n\t"
+		"	bne 1b\n\t"
+
+		/* Issue the command to trigger the SoC power off */
+		"	str	%[gpio_data], [%[gpio_addr]]\n\t"
+
+		/* Trap the processor */
+		"	b .\n\t"
+		: : [srcmd] "r" (srcmd), [sdram_reg] "r" (sdram_reg),
+		    [gpio_addr] "r" (gpio_addr),  [gpio_data] "r" (gpio_data)
+		: "x1");
+
+	panic();
+}
+
+/*****************************************************************************
+ * A8K handlers to shutdown/reboot the system
+ *****************************************************************************
+ */
+
+/* Set a weak stub for platforms that don't configure system power off */
+#pragma weak system_power_off
+int system_power_off(void)
+{
+	return 0;
+}
+
+static void __dead2 a8k_system_off(void)
+{
+	/* Call the platform specific system power off function */
+	system_power_off();
+
+	/* board doesn't have a system off implementation */
+	ERROR("%s:  needs to be implemented\n", __func__);
+	panic();
+}
+
+void plat_marvell_system_reset(void)
+{
+	mmio_write_32(MVEBU_RFU_BASE + MVEBU_RFU_GLOBL_SW_RST, 0x0);
+}
+
+static void __dead2 a8k_system_reset(void)
+{
+	plat_marvell_system_reset();
+
+	/* we shouldn't get to this point */
+	panic();
+}
+
+/*****************************************************************************
+ * Export the platform handlers via plat_arm_psci_pm_ops. The ARM Standard
+ * platform layer will take care of registering the handlers with PSCI.
+ *****************************************************************************
+ */
+const plat_psci_ops_t plat_arm_psci_pm_ops = {
+	.cpu_standby = a8k_cpu_standby,
+	.pwr_domain_on = a8k_pwr_domain_on,
+	.pwr_domain_off = a8k_pwr_domain_off,
+	.pwr_domain_suspend = a8k_pwr_domain_suspend,
+	.pwr_domain_on_finish = a8k_pwr_domain_on_finish,
+	.get_sys_suspend_power_state = a8k_get_sys_suspend_power_state,
+	.pwr_domain_suspend_finish = a8k_pwr_domain_suspend_finish,
+	.pwr_domain_pwr_down_wfi = a8k_pwr_domain_pwr_down_wfi,
+	.system_off = a8k_system_off,
+	.system_reset = a8k_system_reset,
+	.validate_power_state = a8k_validate_power_state,
+	.validate_ns_entrypoint = a8k_validate_ns_entrypoint
+};
diff --git a/plat/marvell/armada/a8k/common/plat_pm_trace.c b/plat/marvell/armada/a8k/common/plat_pm_trace.c
new file mode 100644
index 0000000..e02a893
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/plat_pm_trace.c
@@ -0,0 +1,94 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <lib/mmio.h>
+#include <plat/common/platform.h>
+
+#if MSS_SUPPORT
+#include <mss_mem.h>
+
+#ifdef PM_TRACE_ENABLE
+#include <plat_pm_trace.h>
+
+/* core trace APIs */
+core_trace_func funcTbl[PLATFORM_CORE_COUNT] = {
+	pm_core_0_trace,
+	pm_core_1_trace,
+	pm_core_2_trace,
+	pm_core_3_trace};
+
+/*****************************************************************************
+ * pm_core0_trace
+ * pm_core1_trace
+ * pm_core2_trace
+ * pm_core_3trace
+ *
+ * This functions set trace info into core cyclic trace queue in MSS SRAM
+ * memory space
+ *****************************************************************************
+ */
+void pm_core_0_trace(unsigned int trace)
+{
+	unsigned int current_position_core_0 =
+			mmio_read_32(AP_MSS_ATF_CORE_0_CTRL_BASE);
+	mmio_write_32((AP_MSS_ATF_CORE_0_INFO_BASE  +
+		     (current_position_core_0 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     mmio_read_32(AP_MSS_TIMER_BASE));
+	mmio_write_32((AP_MSS_ATF_CORE_0_INFO_TRACE +
+		     (current_position_core_0 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     trace);
+	mmio_write_32(AP_MSS_ATF_CORE_0_CTRL_BASE,
+		     ((current_position_core_0 + 1) &
+		     AP_MSS_ATF_TRACE_SIZE_MASK));
+}
+
+void pm_core_1_trace(unsigned int trace)
+{
+	unsigned int current_position_core_1 =
+			mmio_read_32(AP_MSS_ATF_CORE_1_CTRL_BASE);
+	mmio_write_32((AP_MSS_ATF_CORE_1_INFO_BASE +
+		     (current_position_core_1 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     mmio_read_32(AP_MSS_TIMER_BASE));
+	mmio_write_32((AP_MSS_ATF_CORE_1_INFO_TRACE +
+		     (current_position_core_1 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     trace);
+	mmio_write_32(AP_MSS_ATF_CORE_1_CTRL_BASE,
+		     ((current_position_core_1 + 1) &
+		     AP_MSS_ATF_TRACE_SIZE_MASK));
+}
+
+void pm_core_2_trace(unsigned int trace)
+{
+	unsigned int current_position_core_2 =
+			mmio_read_32(AP_MSS_ATF_CORE_2_CTRL_BASE);
+	mmio_write_32((AP_MSS_ATF_CORE_2_INFO_BASE +
+		     (current_position_core_2 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     mmio_read_32(AP_MSS_TIMER_BASE));
+	mmio_write_32((AP_MSS_ATF_CORE_2_INFO_TRACE +
+		     (current_position_core_2 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     trace);
+	mmio_write_32(AP_MSS_ATF_CORE_2_CTRL_BASE,
+		     ((current_position_core_2 + 1) &
+		     AP_MSS_ATF_TRACE_SIZE_MASK));
+}
+
+void pm_core_3_trace(unsigned int trace)
+{
+	unsigned int current_position_core_3 =
+			mmio_read_32(AP_MSS_ATF_CORE_3_CTRL_BASE);
+	mmio_write_32((AP_MSS_ATF_CORE_3_INFO_BASE +
+		     (current_position_core_3 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     mmio_read_32(AP_MSS_TIMER_BASE));
+	mmio_write_32((AP_MSS_ATF_CORE_3_INFO_TRACE +
+		     (current_position_core_3 * AP_MSS_ATF_CORE_ENTRY_SIZE)),
+		     trace);
+	mmio_write_32(AP_MSS_ATF_CORE_3_CTRL_BASE,
+		     ((current_position_core_3 + 1) &
+		     AP_MSS_ATF_TRACE_SIZE_MASK));
+}
+#endif /* PM_TRACE_ENABLE */
+#endif /* MSS_SUPPORT */
diff --git a/plat/marvell/armada/a8k/common/plat_thermal.c b/plat/marvell/armada/a8k/common/plat_thermal.c
new file mode 100644
index 0000000..a2fc0d0
--- /dev/null
+++ b/plat/marvell/armada/a8k/common/plat_thermal.c
@@ -0,0 +1,130 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#include <drivers/delay_timer.h>
+#include <drivers/marvell/thermal.h>
+#include <lib/mmio.h>
+
+#include <mvebu_def.h>
+
+#define THERMAL_TIMEOUT					1200
+
+#define THERMAL_SEN_CTRL_LSB_STRT_OFFSET		0
+#define THERMAL_SEN_CTRL_LSB_STRT_MASK			\
+				(0x1 << THERMAL_SEN_CTRL_LSB_STRT_OFFSET)
+#define THERMAL_SEN_CTRL_LSB_RST_OFFSET			1
+#define THERMAL_SEN_CTRL_LSB_RST_MASK			\
+				(0x1 << THERMAL_SEN_CTRL_LSB_RST_OFFSET)
+#define THERMAL_SEN_CTRL_LSB_EN_OFFSET			2
+#define THERMAL_SEN_CTRL_LSB_EN_MASK			\
+				(0x1 << THERMAL_SEN_CTRL_LSB_EN_OFFSET)
+
+#define THERMAL_SEN_CTRL_STATS_VALID_OFFSET		16
+#define THERMAL_SEN_CTRL_STATS_VALID_MASK		\
+				(0x1 << THERMAL_SEN_CTRL_STATS_VALID_OFFSET)
+#define THERMAL_SEN_CTRL_STATS_TEMP_OUT_OFFSET		0
+#define THERMAL_SEN_CTRL_STATS_TEMP_OUT_MASK		\
+			(0x3FF << THERMAL_SEN_CTRL_STATS_TEMP_OUT_OFFSET)
+
+#define THERMAL_SEN_OUTPUT_MSB				512
+#define THERMAL_SEN_OUTPUT_COMP				1024
+
+struct tsen_regs {
+	uint32_t ext_tsen_ctrl_lsb;
+	uint32_t ext_tsen_ctrl_msb;
+	uint32_t ext_tsen_status;
+};
+
+static int ext_tsen_probe(struct tsen_config *tsen_cfg)
+{
+	uint32_t reg, timeout = 0;
+	struct tsen_regs *base;
+
+	if (tsen_cfg == NULL && tsen_cfg->regs_base == NULL) {
+		ERROR("initial thermal sensor configuration is missing\n");
+		return -1;
+	}
+	base = (struct tsen_regs *)tsen_cfg->regs_base;
+
+	INFO("initializing thermal sensor\n");
+
+	/* initialize thermal sensor hardware reset once */
+	reg = mmio_read_32((uintptr_t)&base->ext_tsen_ctrl_lsb);
+	reg &= ~THERMAL_SEN_CTRL_LSB_RST_OFFSET; /* de-assert TSEN_RESET */
+	reg |= THERMAL_SEN_CTRL_LSB_EN_MASK; /* set TSEN_EN to 1 */
+	reg |= THERMAL_SEN_CTRL_LSB_STRT_MASK; /* set TSEN_START to 1 */
+	mmio_write_32((uintptr_t)&base->ext_tsen_ctrl_lsb, reg);
+
+	reg = mmio_read_32((uintptr_t)&base->ext_tsen_status);
+	while ((reg & THERMAL_SEN_CTRL_STATS_VALID_MASK) == 0 &&
+	       timeout < THERMAL_TIMEOUT) {
+		udelay(100);
+		reg = mmio_read_32((uintptr_t)&base->ext_tsen_status);
+		timeout++;
+	}
+
+	if ((reg & THERMAL_SEN_CTRL_STATS_VALID_MASK) == 0) {
+		ERROR("thermal sensor is not ready\n");
+		return -1;
+	}
+
+	tsen_cfg->tsen_ready = 1;
+
+	VERBOSE("thermal sensor was initialized\n");
+
+	return 0;
+}
+
+static int ext_tsen_read(struct tsen_config *tsen_cfg, int *temp)
+{
+	uint32_t reg;
+	struct tsen_regs *base;
+
+	if (tsen_cfg == NULL && !tsen_cfg->tsen_ready) {
+		ERROR("thermal sensor was not initialized\n");
+		return -1;
+	}
+	base = (struct tsen_regs *)tsen_cfg->regs_base;
+
+	reg = mmio_read_32((uintptr_t)&base->ext_tsen_status);
+	reg = ((reg & THERMAL_SEN_CTRL_STATS_TEMP_OUT_MASK) >>
+		THERMAL_SEN_CTRL_STATS_TEMP_OUT_OFFSET);
+
+	/*
+	 * TSEN output format is signed as a 2s complement number
+	 * ranging from-512 to +511. when MSB is set, need to
+	 * calculate the complement number
+	 */
+	if (reg >= THERMAL_SEN_OUTPUT_MSB)
+		reg -= THERMAL_SEN_OUTPUT_COMP;
+
+	if (tsen_cfg->tsen_divisor == 0) {
+		ERROR("thermal sensor divisor cannot be zero\n");
+		return -1;
+	}
+
+	*temp = ((tsen_cfg->tsen_gain * ((int)reg)) +
+		 tsen_cfg->tsen_offset) / tsen_cfg->tsen_divisor;
+
+	return 0;
+}
+
+static struct tsen_config tsen_cfg = {
+	.tsen_offset = 153400,
+	.tsen_gain = 425,
+	.tsen_divisor = 1000,
+	.tsen_ready = 0,
+	.regs_base = (void *)MVEBU_AP_EXT_TSEN_BASE,
+	.ptr_tsen_probe = ext_tsen_probe,
+	.ptr_tsen_read = ext_tsen_read
+};
+
+struct tsen_config *marvell_thermal_config_get(void)
+{
+	return &tsen_cfg;
+}
diff --git a/plat/marvell/armada/common/aarch64/marvell_bl2_mem_params_desc.c b/plat/marvell/armada/common/aarch64/marvell_bl2_mem_params_desc.c
new file mode 100644
index 0000000..6c55858
--- /dev/null
+++ b/plat/marvell/armada/common/aarch64/marvell_bl2_mem_params_desc.c
@@ -0,0 +1,168 @@
+/*
+ * Copyright (c) 2016-2018, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <platform_def.h>
+
+#include <common/bl_common.h>
+#include <common/desc_image_load.h>
+#include <marvell_def.h>
+#include <plat/common/platform.h>
+
+/*******************************************************************************
+ * Following descriptor provides BL image/ep information that gets used
+ * by BL2 to load the images and also subset of this information is
+ * passed to next BL image. The image loading sequence is managed by
+ * populating the images in required loading order. The image execution
+ * sequence is managed by populating the `next_handoff_image_id` with
+ * the next executable image id.
+ ******************************************************************************/
+static bl_mem_params_node_t bl2_mem_params_descs[] = {
+#ifdef SCP_BL2_BASE
+	/* Fill SCP_BL2 related information if it exists */
+	{
+		.image_id = SCP_BL2_IMAGE_ID,
+
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_IMAGE_BINARY,
+			VERSION_2, entry_point_info_t, SECURE | NON_EXECUTABLE),
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_IMAGE_BINARY,
+			VERSION_2, image_info_t, 0),
+		.image_info.image_base = SCP_BL2_BASE,
+		.image_info.image_max_size = SCP_BL2_SIZE,
+
+		.next_handoff_image_id = INVALID_IMAGE_ID,
+	},
+#endif /* SCP_BL2_BASE */
+
+#ifdef EL3_PAYLOAD_BASE
+	/* Fill EL3 payload related information (BL31 is EL3 payload)*/
+	{
+		.image_id = BL31_IMAGE_ID,
+
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+			VERSION_2, entry_point_info_t,
+			SECURE | EXECUTABLE | EP_FIRST_EXE),
+		.ep_info.pc = EL3_PAYLOAD_BASE,
+		.ep_info.spsr = SPSR_64(MODE_EL3, MODE_SP_ELX,
+			DISABLE_ALL_EXCEPTIONS),
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t,
+			IMAGE_ATTRIB_PLAT_SETUP | IMAGE_ATTRIB_SKIP_LOADING),
+
+		.next_handoff_image_id = INVALID_IMAGE_ID,
+	},
+
+#else /* EL3_PAYLOAD_BASE */
+
+	/* Fill BL31 related information */
+	{
+		.image_id = BL31_IMAGE_ID,
+
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+			VERSION_2, entry_point_info_t,
+			SECURE | EXECUTABLE | EP_FIRST_EXE),
+		.ep_info.pc = BL31_BASE,
+		.ep_info.spsr = SPSR_64(MODE_EL3, MODE_SP_ELX,
+			DISABLE_ALL_EXCEPTIONS),
+#if DEBUG
+		.ep_info.args.arg3 = MARVELL_BL31_PLAT_PARAM_VAL,
+#endif
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t, IMAGE_ATTRIB_PLAT_SETUP),
+		.image_info.image_base = BL31_BASE,
+		.image_info.image_max_size = BL31_LIMIT - BL31_BASE,
+
+# ifdef BL32_BASE
+		.next_handoff_image_id = BL32_IMAGE_ID,
+# else
+		.next_handoff_image_id = BL33_IMAGE_ID,
+# endif
+	},
+
+# ifdef BL32_BASE
+	/* Fill BL32 related information */
+	{
+		.image_id = BL32_IMAGE_ID,
+
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+			VERSION_2, entry_point_info_t, SECURE | EXECUTABLE),
+		.ep_info.pc = BL32_BASE,
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t, 0),
+		.image_info.image_base = BL32_BASE,
+		.image_info.image_max_size = BL32_LIMIT - BL32_BASE,
+
+		.next_handoff_image_id = BL33_IMAGE_ID,
+	},
+
+	/*
+	 * Fill BL32 external 1 related information.
+	 * A typical use for extra1 image is with OP-TEE
+	 * where it is the pager image.
+	 */
+	{
+		.image_id = BL32_EXTRA1_IMAGE_ID,
+
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+		VERSION_2, entry_point_info_t, SECURE | NON_EXECUTABLE),
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t, IMAGE_ATTRIB_SKIP_LOADING),
+		.image_info.image_base = BL32_BASE,
+		.image_info.image_max_size = BL32_LIMIT - BL32_BASE,
+
+		.next_handoff_image_id = INVALID_IMAGE_ID,
+	},
+
+	/*
+	 * Fill BL32 external 2 related information.
+	 * A typical use for extra2 image is with OP-TEE,
+	 * where it is the paged image.
+	 */
+	{
+		.image_id = BL32_EXTRA2_IMAGE_ID,
+
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+			VERSION_2, entry_point_info_t, SECURE | NON_EXECUTABLE),
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t, IMAGE_ATTRIB_SKIP_LOADING),
+#ifdef SPD_opteed
+		.image_info.image_base = MARVELL_OPTEE_PAGEABLE_LOAD_BASE,
+		.image_info.image_max_size = MARVELL_OPTEE_PAGEABLE_LOAD_SIZE,
+#endif
+		.next_handoff_image_id = INVALID_IMAGE_ID,
+	},
+# endif /* BL32_BASE */
+
+	/* Fill BL33 related information */
+	{
+		.image_id = BL33_IMAGE_ID,
+		SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+			VERSION_2, entry_point_info_t, NON_SECURE | EXECUTABLE),
+# ifdef PRELOADED_BL33_BASE
+		.ep_info.pc = PRELOADED_BL33_BASE,
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t, IMAGE_ATTRIB_SKIP_LOADING),
+# else
+		.ep_info.pc = MARVELL_DRAM_BASE,
+
+		SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+			VERSION_2, image_info_t, 0),
+		.image_info.image_base = MARVELL_DRAM_BASE,
+		.image_info.image_max_size = MARVELL_DRAM_SIZE,
+# endif /* PRELOADED_BL33_BASE */
+
+		.next_handoff_image_id = INVALID_IMAGE_ID,
+	}
+#endif /* EL3_PAYLOAD_BASE */
+};
+
+REGISTER_BL_IMAGE_DESCS(bl2_mem_params_descs)
diff --git a/plat/marvell/armada/common/aarch64/marvell_common.c b/plat/marvell/armada/common/aarch64/marvell_common.c
new file mode 100644
index 0000000..21a62d4
--- /dev/null
+++ b/plat/marvell/armada/common/aarch64/marvell_common.c
@@ -0,0 +1,137 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+
+#include <platform_def.h>
+
+#include <arch.h>
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <lib/mmio.h>
+#include <lib/xlat_tables/xlat_tables_v2.h>
+
+#include <plat_marvell.h>
+
+/* Weak definitions may be overridden in specific ARM standard platform */
+#pragma weak plat_get_ns_image_entrypoint
+#pragma weak plat_marvell_get_mmap
+
+/*
+ * Set up the page tables for the generic and platform-specific memory regions.
+ * The extents of the generic memory regions are specified by the function
+ * arguments and consist of:
+ * - Trusted SRAM seen by the BL image;
+ * - Code section;
+ * - Read-only data section;
+ * - Coherent memory region, if applicable.
+ */
+void marvell_setup_page_tables(uintptr_t total_base,
+			       size_t total_size,
+			       uintptr_t code_start,
+			       uintptr_t code_limit,
+			       uintptr_t rodata_start,
+			       uintptr_t rodata_limit
+#if USE_COHERENT_MEM
+			       ,
+			       uintptr_t coh_start,
+			       uintptr_t coh_limit
+#endif
+			   )
+{
+	/*
+	 * Map the Trusted SRAM with appropriate memory attributes.
+	 * Subsequent mappings will adjust the attributes for specific regions.
+	 */
+	VERBOSE("Trusted SRAM seen by this BL image: %p - %p\n",
+		(void *) total_base, (void *) (total_base + total_size));
+	mmap_add_region(total_base, total_base,
+			total_size,
+			MT_MEMORY | MT_RW | MT_SECURE);
+
+	/* Re-map the code section */
+	VERBOSE("Code region: %p - %p\n",
+		(void *) code_start, (void *) code_limit);
+	mmap_add_region(code_start, code_start,
+			code_limit - code_start,
+			MT_CODE | MT_SECURE);
+
+	/* Re-map the read-only data section */
+	VERBOSE("Read-only data region: %p - %p\n",
+		(void *) rodata_start, (void *) rodata_limit);
+	mmap_add_region(rodata_start, rodata_start,
+			rodata_limit - rodata_start,
+			MT_RO_DATA | MT_SECURE);
+
+#if USE_COHERENT_MEM
+	/* Re-map the coherent memory region */
+	VERBOSE("Coherent region: %p - %p\n",
+		(void *) coh_start, (void *) coh_limit);
+	mmap_add_region(coh_start, coh_start,
+			coh_limit - coh_start,
+			MT_DEVICE | MT_RW | MT_SECURE);
+#endif
+
+	/* Now (re-)map the platform-specific memory regions */
+	mmap_add(plat_marvell_get_mmap());
+
+	/* Create the page tables to reflect the above mappings */
+	init_xlat_tables();
+}
+
+unsigned long plat_get_ns_image_entrypoint(void)
+{
+	return PLAT_MARVELL_NS_IMAGE_OFFSET;
+}
+
+/*****************************************************************************
+ * Gets SPSR for BL32 entry
+ *****************************************************************************
+ */
+uint32_t marvell_get_spsr_for_bl32_entry(void)
+{
+	/*
+	 * The Secure Payload Dispatcher service is responsible for
+	 * setting the SPSR prior to entry into the BL32 image.
+	 */
+	return 0;
+}
+
+/*****************************************************************************
+ * Gets SPSR for BL33 entry
+ *****************************************************************************
+ */
+uint32_t marvell_get_spsr_for_bl33_entry(void)
+{
+	unsigned long el_status;
+	unsigned int mode;
+	uint32_t spsr;
+
+	/* Figure out what mode we enter the non-secure world in */
+	el_status = read_id_aa64pfr0_el1() >> ID_AA64PFR0_EL2_SHIFT;
+	el_status &= ID_AA64PFR0_ELX_MASK;
+
+	mode = (el_status) ? MODE_EL2 : MODE_EL1;
+
+	/*
+	 * TODO: Consider the possibility of specifying the SPSR in
+	 * the FIP ToC and allowing the platform to have a say as
+	 * well.
+	 */
+	spsr = SPSR_64(mode, MODE_SP_ELX, DISABLE_ALL_EXCEPTIONS);
+	return spsr;
+}
+
+/*****************************************************************************
+ * Returns ARM platform specific memory map regions.
+ *****************************************************************************
+ */
+const mmap_region_t *plat_marvell_get_mmap(void)
+{
+	return plat_marvell_mmap;
+}
+
diff --git a/plat/marvell/armada/common/aarch64/marvell_helpers.S b/plat/marvell/armada/common/aarch64/marvell_helpers.S
new file mode 100644
index 0000000..3038ec0
--- /dev/null
+++ b/plat/marvell/armada/common/aarch64/marvell_helpers.S
@@ -0,0 +1,259 @@
+/*
+ * Copyright (c) 2020, ARM Limited. All rights reserved.
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <asm_macros.S>
+#include <cortex_a72.h>
+#ifndef PLAT_a3700
+#include <drivers/marvell/ccu.h>
+#include <drivers/marvell/cache_llc.h>
+#endif
+#include <marvell_def.h>
+#include <platform_def.h>
+
+	.weak	plat_marvell_calc_core_pos
+	.weak	plat_my_core_pos
+	.globl	plat_crash_console_init
+	.globl	plat_crash_console_putc
+	.globl	plat_crash_console_flush
+	.globl	platform_mem_init
+	.globl	disable_mmu_dcache
+	.globl	invalidate_tlb_all
+	.globl	platform_unmap_sram
+	.globl	disable_sram
+	.globl	disable_icache
+	.globl	invalidate_icache_all
+	.globl	marvell_exit_bootrom
+	.globl	ca72_l2_enable_unique_clean
+
+	/* -----------------------------------------------------
+	 *  unsigned int plat_my_core_pos(void)
+	 *  This function uses the plat_marvell_calc_core_pos()
+	 *  definition to get the index of the calling CPU.
+	 * -----------------------------------------------------
+	 */
+func plat_my_core_pos
+	mrs	x0, mpidr_el1
+	b	plat_marvell_calc_core_pos
+endfunc plat_my_core_pos
+
+	/* -----------------------------------------------------
+	 *  unsigned int plat_marvell_calc_core_pos(uint64_t mpidr)
+	 *  Helper function to calculate the core position.
+	 *  With this function: CorePos = (ClusterId * 2) +
+	 *  				  CoreId
+	 * -----------------------------------------------------
+	 */
+func plat_marvell_calc_core_pos
+	and	x1, x0, #MPIDR_CPU_MASK
+	and	x0, x0, #MPIDR_CLUSTER_MASK
+	add	x0, x1, x0, LSR #7
+	ret
+endfunc plat_marvell_calc_core_pos
+
+	/* ---------------------------------------------
+	 * int plat_crash_console_init(void)
+	 * Function to initialize the crash console
+	 * without a C Runtime to print crash report.
+	 * Clobber list : x0, x1, x2
+	 * ---------------------------------------------
+	 */
+func plat_crash_console_init
+#ifdef PLAT_a3700
+	mov	x1, x30
+	bl	get_ref_clk
+	mov	x30, x1
+	mov_imm	x1, 1000000
+	mul	x1, x0, x1
+#else
+	mov_imm	x1, PLAT_MARVELL_UART_CLK_IN_HZ
+#endif
+	mov_imm	x0, PLAT_MARVELL_UART_BASE
+	mov_imm	x2, MARVELL_CONSOLE_BAUDRATE
+#ifdef PLAT_a3700
+	b	console_a3700_core_init
+#else
+	b	console_16550_core_init
+#endif
+endfunc plat_crash_console_init
+
+	/* ---------------------------------------------
+	 * int plat_crash_console_putc(int c)
+	 * Function to print a character on the crash
+	 * console without a C Runtime.
+	 * Clobber list : x1, x2
+	 * ---------------------------------------------
+	 */
+func plat_crash_console_putc
+	mov_imm	x1, PLAT_MARVELL_UART_BASE
+#ifdef PLAT_a3700
+
+	b	console_a3700_core_putc
+#else
+	b	console_16550_core_putc
+#endif
+endfunc plat_crash_console_putc
+
+	/* ---------------------------------------------
+	 * void plat_crash_console_flush()
+	 * Function to force a write of all buffered
+	 * data that hasn't been output.
+	 * Out : void.
+	 * Clobber list : r0
+	 * ---------------------------------------------
+	 */
+func plat_crash_console_flush
+	mov_imm	x0, PLAT_MARVELL_UART_BASE
+#ifdef PLAT_a3700
+	b	console_a3700_core_flush
+#else
+	b	console_16550_core_flush
+#endif
+endfunc plat_crash_console_flush
+
+	/* ---------------------------------------------------------------------
+	 * We don't need to carry out any memory initialization on ARM
+	 * platforms. The Secure RAM is accessible straight away.
+	 * ---------------------------------------------------------------------
+	 */
+func platform_mem_init
+	ret
+endfunc platform_mem_init
+
+	/* -----------------------------------------------------
+	 * Disable icache, dcache, and MMU
+	 * -----------------------------------------------------
+	 */
+func disable_mmu_dcache
+	mrs	x0, sctlr_el3
+	bic	x0, x0, 0x1		/* M bit - MMU */
+	bic	x0, x0, 0x4		/* C bit - Dcache L1 & L2 */
+	msr	sctlr_el3, x0
+	isb
+	b	mmu_off
+mmu_off:
+	ret
+endfunc disable_mmu_dcache
+
+	/* -----------------------------------------------------
+	 * Disable all TLB entries
+	 * -----------------------------------------------------
+	 */
+func invalidate_tlb_all
+	tlbi	alle3
+	dsb	sy
+	isb
+	ret
+endfunc invalidate_tlb_all
+
+	/* -----------------------------------------------------
+	 * Disable the i cache
+	 * -----------------------------------------------------
+	 */
+func disable_icache
+	mrs 	x0, sctlr_el3
+	bic	x0, x0, 0x1000	/* I bit - Icache L1 & L2 */
+	msr	sctlr_el3, x0
+	isb
+	ret
+endfunc disable_icache
+
+	/* -----------------------------------------------------
+	 * Disable all of the i caches
+	 * -----------------------------------------------------
+	 */
+func invalidate_icache_all
+	ic	ialluis
+	isb	sy
+	ret
+endfunc invalidate_icache_all
+
+	/* -----------------------------------------------------
+	 * Clear the SRAM enabling bit to unmap SRAM
+	 * -----------------------------------------------------
+	 */
+func platform_unmap_sram
+	ldr	x0, =CCU_SRAM_WIN_CR
+	str	wzr, [x0]
+	ret
+endfunc platform_unmap_sram
+
+	/* -----------------------------------------------------
+	 * Disable the SRAM
+	 * -----------------------------------------------------
+	 */
+func disable_sram
+	/* Disable the line lockings. They must be disabled expictly
+	 * or the OS will have problems using the cache */
+	ldr	x1, =MASTER_LLC_TC0_LOCK
+	str	wzr, [x1]
+
+	/* Invalidate all ways */
+	ldr	w1, =LLC_WAY_MASK
+	ldr	x0, =MASTER_LLC_INV_WAY
+	str	w1, [x0]
+
+	/* Finally disable LLC */
+	ldr	x0, =MASTER_LLC_CTRL
+	str	wzr, [x0]
+
+	ret
+endfunc disable_sram
+
+	/* -----------------------------------------------------
+	 * Operation when exit bootROM:
+	 * Disable the MMU
+	 * Disable and invalidate the dcache
+	 * Unmap and disable the SRAM
+	 * Disable and invalidate the icache
+	 * -----------------------------------------------------
+	 */
+func marvell_exit_bootrom
+	/* Save the system restore address */
+	mov	x28, x0
+
+	/* Close the caches and MMU */
+	bl	disable_mmu_dcache
+
+	/*
+	 * There is nothing important in the caches now,
+	 * so invalidate them instead of cleaning.
+	 */
+	adr	x0, __RW_START__
+	adr	x1, __RW_END__
+	sub	x1, x1, x0
+	bl	inv_dcache_range
+	bl	invalidate_tlb_all
+
+	/*
+	 * Clean the memory mapping of SRAM
+	 * the DDR mapping will remain to enable boot image to execute
+	 */
+	bl	platform_unmap_sram
+
+	/* Disable the SRAM */
+	bl	disable_sram
+
+	/* Disable and invalidate icache */
+	bl	disable_icache
+	bl	invalidate_icache_all
+
+	mov	x0, x28
+	br	x0
+endfunc marvell_exit_bootrom
+
+	/*
+	 * Enable L2 UniqueClean evictions with data
+	 */
+func ca72_l2_enable_unique_clean
+
+	mrs	x0, CORTEX_A72_L2ACTLR_EL1
+	orr	x0, x0, #CORTEX_A72_L2ACTLR_ENABLE_UNIQUE_CLEAN
+	msr	CORTEX_A72_L2ACTLR_EL1, x0
+
+	ret
+endfunc ca72_l2_enable_unique_clean
diff --git a/plat/marvell/armada/common/marvell_bl1_setup.c b/plat/marvell/armada/common/marvell_bl1_setup.c
new file mode 100644
index 0000000..7b7cef3
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_bl1_setup.c
@@ -0,0 +1,105 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+#include <bl1/bl1.h>
+#include <common/bl_common.h>
+#include <common/debug.h>
+#include <drivers/arm/sp805.h>
+#include <drivers/console.h>
+#include <plat/common/platform.h>
+
+#include <plat_marvell.h>
+
+/* Weak definitions may be overridden in specific Marvell standard platform */
+#pragma weak bl1_early_platform_setup
+#pragma weak bl1_plat_arch_setup
+#pragma weak bl1_platform_setup
+#pragma weak bl1_plat_sec_mem_layout
+
+/* Data structure which holds the extents of the RAM for BL1*/
+static meminfo_t bl1_ram_layout;
+
+meminfo_t *bl1_plat_sec_mem_layout(void)
+{
+	return &bl1_ram_layout;
+}
+
+/*
+ * BL1 specific platform actions shared between Marvell standard platforms.
+ */
+void marvell_bl1_early_platform_setup(void)
+{
+	/* Initialize the console to provide early debug support */
+	marvell_console_boot_init();
+
+	/* Allow BL1 to see the whole Trusted RAM */
+	bl1_ram_layout.total_base = MARVELL_BL_RAM_BASE;
+	bl1_ram_layout.total_size = MARVELL_BL_RAM_SIZE;
+}
+
+void bl1_early_platform_setup(void)
+{
+	marvell_bl1_early_platform_setup();
+}
+
+/*
+ * Perform the very early platform specific architecture setup shared between
+ * MARVELL standard platforms. This only does basic initialization. Later
+ * architectural setup (bl1_arch_setup()) does not do anything platform
+ * specific.
+ */
+void marvell_bl1_plat_arch_setup(void)
+{
+	marvell_setup_page_tables(bl1_ram_layout.total_base,
+				  bl1_ram_layout.total_size,
+				  BL1_RO_BASE,
+				  BL1_RO_LIMIT,
+				  BL1_RO_DATA_BASE,
+				  BL1_RO_DATA_END
+#if USE_COHERENT_MEM
+				, BL_COHERENT_RAM_BASE,
+				  BL_COHERENT_RAM_END
+#endif
+				);
+	enable_mmu_el3(0);
+}
+
+void bl1_plat_arch_setup(void)
+{
+	marvell_bl1_plat_arch_setup();
+}
+
+/*
+ * Perform the platform specific architecture setup shared between
+ * MARVELL standard platforms.
+ */
+void marvell_bl1_platform_setup(void)
+{
+	/* Initialise the IO layer and register platform IO devices */
+	plat_marvell_io_setup();
+}
+
+void bl1_platform_setup(void)
+{
+	marvell_bl1_platform_setup();
+}
+
+void bl1_plat_prepare_exit(entry_point_info_t *ep_info)
+{
+#ifdef EL3_PAYLOAD_BASE
+	/*
+	 * Program the EL3 payload's entry point address into the CPUs mailbox
+	 * in order to release secondary CPUs from their holding pen and make
+	 * them jump there.
+	 */
+	marvell_program_trusted_mailbox(ep_info->pc);
+	dsbsy();
+	sev();
+#endif
+}
diff --git a/plat/marvell/armada/common/marvell_bl2_setup.c b/plat/marvell/armada/common/marvell_bl2_setup.c
new file mode 100644
index 0000000..3dfa82e
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_bl2_setup.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+#include <string.h>
+
+#include <platform_def.h>
+
+#include <arch_helpers.h>
+#include <common/bl_common.h>
+#include <common/debug.h>
+#include <common/desc_image_load.h>
+#include <drivers/console.h>
+#include <lib/utils.h>
+
+#ifdef SPD_opteed
+#include <optee_utils.h>
+#endif
+#include <marvell_def.h>
+#include <plat_marvell.h>
+
+/* Data structure which holds the extents of the trusted SRAM for BL2 */
+static meminfo_t bl2_tzram_layout __aligned(CACHE_WRITEBACK_GRANULE);
+
+/* Weak definitions may be overridden in specific MARVELL standard platform */
+#pragma weak bl2_early_platform_setup2
+#pragma weak bl2_platform_setup
+#pragma weak bl2_plat_arch_setup
+#pragma weak bl2_plat_sec_mem_layout
+
+meminfo_t *bl2_plat_sec_mem_layout(void)
+{
+	return &bl2_tzram_layout;
+}
+
+/*****************************************************************************
+ * BL1 has passed the extents of the trusted SRAM that should be visible to BL2
+ * in x0. This memory layout is sitting at the base of the free trusted SRAM.
+ * Copy it to a safe location before its reclaimed by later BL2 functionality.
+ *****************************************************************************
+ */
+void marvell_bl2_early_platform_setup(meminfo_t *mem_layout)
+{
+	/* Initialize the console to provide early debug support */
+	marvell_console_boot_init();
+
+	/* Setup the BL2 memory layout */
+	bl2_tzram_layout = *mem_layout;
+
+	/* Initialise the IO layer and register platform IO devices */
+	plat_marvell_io_setup();
+}
+
+
+void bl2_early_platform_setup2(u_register_t arg0, u_register_t arg1,
+			       u_register_t arg2, u_register_t arg3)
+{
+	struct meminfo *mem_layout = (struct meminfo *)arg1;
+
+	marvell_bl2_early_platform_setup(mem_layout);
+}
+
+void bl2_platform_setup(void)
+{
+	/* Nothing to do */
+}
+
+/*****************************************************************************
+ * Perform the very early platform specific architectural setup here. At the
+ * moment this is only initializes the mmu in a quick and dirty way.
+ *****************************************************************************
+ */
+void marvell_bl2_plat_arch_setup(void)
+{
+	marvell_setup_page_tables(bl2_tzram_layout.total_base,
+				  bl2_tzram_layout.total_size,
+				  BL_CODE_BASE,
+				  BL_CODE_END,
+				  BL_RO_DATA_BASE,
+				  BL_RO_DATA_END
+#if USE_COHERENT_MEM
+				, BL_COHERENT_RAM_BASE,
+				  BL_COHERENT_RAM_END
+#endif
+			      );
+	enable_mmu_el1(0);
+}
+
+void bl2_plat_arch_setup(void)
+{
+	marvell_bl2_plat_arch_setup();
+}
+
+int marvell_bl2_handle_post_image_load(unsigned int image_id)
+{
+	int err = 0;
+	bl_mem_params_node_t *bl_mem_params = get_bl_mem_params_node(image_id);
+
+#ifdef SPD_opteed
+	bl_mem_params_node_t *pager_mem_params = NULL;
+	bl_mem_params_node_t *paged_mem_params = NULL;
+#endif /* SPD_opteed */
+	assert(bl_mem_params);
+
+	switch (image_id) {
+	case BL32_IMAGE_ID:
+#ifdef SPD_opteed
+		pager_mem_params = get_bl_mem_params_node(BL32_EXTRA1_IMAGE_ID);
+		assert(pager_mem_params);
+
+		paged_mem_params = get_bl_mem_params_node(BL32_EXTRA2_IMAGE_ID);
+		assert(paged_mem_params);
+
+		err = parse_optee_header(&bl_mem_params->ep_info,
+					 &pager_mem_params->image_info,
+					 &paged_mem_params->image_info);
+		if (err != 0)
+			WARN("OPTEE header parse error.\n");
+#endif /* SPD_opteed */
+		bl_mem_params->ep_info.spsr = marvell_get_spsr_for_bl32_entry();
+		break;
+
+	case BL33_IMAGE_ID:
+		/* BL33 expects to receive the primary CPU MPID (through r0) */
+		bl_mem_params->ep_info.args.arg0 = 0xffff & read_mpidr();
+		bl_mem_params->ep_info.spsr = marvell_get_spsr_for_bl33_entry();
+		break;
+#ifdef SCP_BL2_BASE
+	case SCP_BL2_IMAGE_ID:
+		/* The subsequent handling of SCP_BL2 is platform specific */
+		err = bl2_plat_handle_scp_bl2(&bl_mem_params->image_info);
+		if (err) {
+			WARN("Failure in platform-specific handling of SCP_BL2 image.\n");
+		}
+		break;
+#endif
+	default:
+		/* Do nothing in default case */
+		break;
+	}
+
+	return err;
+
+}
+
+/*******************************************************************************
+ * This function can be used by the platforms to update/use image
+ * information for given `image_id`.
+ ******************************************************************************/
+int bl2_plat_handle_post_image_load(unsigned int image_id)
+{
+	return marvell_bl2_handle_post_image_load(image_id);
+}
+
diff --git a/plat/marvell/armada/common/marvell_bl31_setup.c b/plat/marvell/armada/common/marvell_bl31_setup.c
new file mode 100644
index 0000000..26ba906
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_bl31_setup.c
@@ -0,0 +1,237 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+
+#include <arch.h>
+#include <common/bl_common.h>
+#include <common/debug.h>
+#ifdef USE_CCI
+#include <drivers/arm/cci.h>
+#endif
+#include <drivers/console.h>
+#include <plat/common/platform.h>
+
+#include <marvell_def.h>
+#include <marvell_plat_priv.h>
+#include <plat_marvell.h>
+
+/*
+ * Placeholder variables for copying the arguments that have been passed to
+ * BL31 from BL2.
+ */
+static entry_point_info_t bl32_image_ep_info;
+static entry_point_info_t bl33_image_ep_info;
+
+/* Weak definitions may be overridden in specific ARM standard platform */
+#pragma weak bl31_early_platform_setup2
+#pragma weak bl31_platform_setup
+#pragma weak bl31_plat_arch_setup
+#pragma weak bl31_plat_get_next_image_ep_info
+#pragma weak plat_get_syscnt_freq2
+
+/*****************************************************************************
+ * Return a pointer to the 'entry_point_info' structure of the next image for
+ * the security state specified. BL33 corresponds to the non-secure image type
+ * while BL32 corresponds to the secure image type. A NULL pointer is returned
+ * if the image does not exist.
+ *****************************************************************************
+ */
+entry_point_info_t *bl31_plat_get_next_image_ep_info(uint32_t type)
+{
+	entry_point_info_t *next_image_info;
+
+	assert(sec_state_is_valid(type));
+	next_image_info = (type == NON_SECURE)
+			? &bl33_image_ep_info : &bl32_image_ep_info;
+
+	return next_image_info;
+}
+
+/*****************************************************************************
+ * Perform any BL31 early platform setup common to ARM standard platforms.
+ * Here is an opportunity to copy parameters passed by the calling EL (S-EL1
+ * in BL2 & EL3 in BL1) before they are lost (potentially). This needs to be
+ * done before the MMU is initialized so that the memory layout can be used
+ * while creating page tables. BL2 has flushed this information to memory, so
+ * we are guaranteed to pick up good data.
+ *****************************************************************************
+ */
+void marvell_bl31_early_platform_setup(void *from_bl2,
+				       uintptr_t soc_fw_config,
+				       uintptr_t hw_config,
+				       void *plat_params_from_bl2)
+{
+	/* Initialize the console to provide early debug support */
+	marvell_console_boot_init();
+
+#if RESET_TO_BL31
+	/* There are no parameters from BL2 if BL31 is a reset vector */
+	assert(from_bl2 == NULL);
+	assert(plat_params_from_bl2 == NULL);
+
+#ifdef BL32_BASE
+	/* Populate entry point information for BL32 */
+	SET_PARAM_HEAD(&bl32_image_ep_info,
+				PARAM_EP,
+				VERSION_1,
+				0);
+	SET_SECURITY_STATE(bl32_image_ep_info.h.attr, SECURE);
+	bl32_image_ep_info.pc = BL32_BASE;
+	bl32_image_ep_info.spsr = marvell_get_spsr_for_bl32_entry();
+#endif /* BL32_BASE */
+
+	/* Populate entry point information for BL33 */
+	SET_PARAM_HEAD(&bl33_image_ep_info,
+				PARAM_EP,
+				VERSION_1,
+				0);
+	/*
+	 * Tell BL31 where the non-trusted software image
+	 * is located and the entry state information
+	 */
+	bl33_image_ep_info.pc = plat_get_ns_image_entrypoint();
+	bl33_image_ep_info.spsr = marvell_get_spsr_for_bl33_entry();
+	SET_SECURITY_STATE(bl33_image_ep_info.h.attr, NON_SECURE);
+
+#else
+	/*
+	 * In debug builds, we pass a special value in 'plat_params_from_bl2'
+	 * to verify platform parameters from BL2 to BL31.
+	 * In release builds, it's not used.
+	 */
+	assert(((unsigned long long)plat_params_from_bl2) ==
+		MARVELL_BL31_PLAT_PARAM_VAL);
+
+	/*
+	 * Check params passed from BL2 should not be NULL,
+	 */
+	bl_params_t *params_from_bl2 = (bl_params_t *)from_bl2;
+	assert(params_from_bl2 != NULL);
+	assert(params_from_bl2->h.type == PARAM_BL_PARAMS);
+	assert(params_from_bl2->h.version >= VERSION_2);
+
+	bl_params_node_t *bl_params = params_from_bl2->head;
+
+	/*
+	 * Copy BL33 and BL32 (if present), entry point information.
+	 * They are stored in Secure RAM, in BL2's address space.
+	 */
+	while (bl_params != NULL) {
+		if (bl_params->image_id == BL32_IMAGE_ID)
+			bl32_image_ep_info = *bl_params->ep_info;
+
+		if (bl_params->image_id == BL33_IMAGE_ID)
+			bl33_image_ep_info = *bl_params->ep_info;
+
+		bl_params = bl_params->next_params_info;
+	}
+#endif
+}
+
+void bl31_early_platform_setup2(u_register_t arg0, u_register_t arg1,
+				u_register_t arg2, u_register_t arg3)
+
+{
+	marvell_bl31_early_platform_setup((void *)arg0, arg1, arg2,
+					  (void *)arg3);
+
+#ifdef USE_CCI
+	/*
+	 * Initialize CCI for this cluster during cold boot.
+	 * No need for locks as no other CPU is active.
+	 */
+	plat_marvell_interconnect_init();
+
+	/*
+	 * Enable CCI coherency for the primary CPU's cluster.
+	 * Platform specific PSCI code will enable coherency for other
+	 * clusters.
+	 */
+	plat_marvell_interconnect_enter_coherency();
+#endif
+}
+
+/*****************************************************************************
+ * Perform any BL31 platform setup common to ARM standard platforms
+ *****************************************************************************
+ */
+void marvell_bl31_platform_setup(void)
+{
+	/* Initialize the GIC driver, cpu and distributor interfaces */
+	plat_marvell_gic_driver_init();
+	plat_marvell_gic_init();
+
+	/* For Armada-8k-plus family, the SoC includes more than
+	 * a single AP die, but the default die that boots is AP #0.
+	 * For other families there is only one die (#0).
+	 * Initialize psci arch from die 0
+	 */
+	marvell_psci_arch_init(0);
+}
+
+/*****************************************************************************
+ * Perform any BL31 platform runtime setup prior to BL31 exit common to ARM
+ * standard platforms
+ *****************************************************************************
+ */
+void marvell_bl31_plat_runtime_setup(void)
+{
+	console_switch_state(CONSOLE_FLAG_RUNTIME);
+
+	/* Initialize the runtime console */
+	marvell_console_runtime_init();
+}
+
+void bl31_platform_setup(void)
+{
+	marvell_bl31_platform_setup();
+}
+
+void bl31_plat_runtime_setup(void)
+{
+	marvell_bl31_plat_runtime_setup();
+}
+
+/*****************************************************************************
+ * Perform the very early platform specific architectural setup shared between
+ * ARM standard platforms. This only does basic initialization. Later
+ * architectural setup (bl31_arch_setup()) does not do anything platform
+ * specific.
+ *****************************************************************************
+ */
+void marvell_bl31_plat_arch_setup(void)
+{
+	marvell_setup_page_tables(BL31_BASE,
+				  BL31_END - BL31_BASE,
+				  BL_CODE_BASE,
+				  BL_CODE_END,
+				  BL_RO_DATA_BASE,
+				  BL_RO_DATA_END
+#if USE_COHERENT_MEM
+				, BL_COHERENT_RAM_BASE,
+				  BL_COHERENT_RAM_END
+#endif
+			);
+
+#if BL31_CACHE_DISABLE
+	enable_mmu_el3(DISABLE_DCACHE);
+	INFO("Cache is disabled in BL3\n");
+#else
+	enable_mmu_el3(0);
+#endif
+}
+
+void bl31_plat_arch_setup(void)
+{
+	marvell_bl31_plat_arch_setup();
+}
+
+unsigned int plat_get_syscnt_freq2(void)
+{
+	return PLAT_REF_CLK_IN_HZ;
+}
diff --git a/plat/marvell/armada/common/marvell_cci.c b/plat/marvell/armada/common/marvell_cci.c
new file mode 100644
index 0000000..80351ae
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_cci.c
@@ -0,0 +1,52 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <drivers/arm/cci.h>
+
+#include <plat_marvell.h>
+
+static const int cci_map[] = {
+	PLAT_MARVELL_CCI_CLUSTER0_SL_IFACE_IX,
+	PLAT_MARVELL_CCI_CLUSTER1_SL_IFACE_IX
+};
+
+/****************************************************************************
+ * The following functions are defined as weak to allow a platform to override
+ * the way ARM CCI driver is initialised and used.
+ ****************************************************************************
+ */
+#pragma weak plat_marvell_interconnect_init
+#pragma weak plat_marvell_interconnect_enter_coherency
+#pragma weak plat_marvell_interconnect_exit_coherency
+
+
+/****************************************************************************
+ * Helper function to initialize ARM CCI driver.
+ ****************************************************************************
+ */
+void plat_marvell_interconnect_init(void)
+{
+	cci_init(PLAT_MARVELL_CCI_BASE, cci_map, ARRAY_SIZE(cci_map));
+}
+
+/****************************************************************************
+ * Helper function to place current master into coherency
+ ****************************************************************************
+ */
+void plat_marvell_interconnect_enter_coherency(void)
+{
+	cci_enable_snoop_dvm_reqs(MPIDR_AFFLVL1_VAL(read_mpidr_el1()));
+}
+
+/****************************************************************************
+ * Helper function to remove current master from coherency
+ ****************************************************************************
+ */
+void plat_marvell_interconnect_exit_coherency(void)
+{
+	cci_disable_snoop_dvm_reqs(MPIDR_AFFLVL1_VAL(read_mpidr_el1()));
+}
diff --git a/plat/marvell/armada/common/marvell_common.mk b/plat/marvell/armada/common/marvell_common.mk
new file mode 100644
index 0000000..f0e6edf
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_common.mk
@@ -0,0 +1,99 @@
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+
+MARVELL_PLAT_BASE		:= plat/marvell/armada
+MARVELL_PLAT_INCLUDE_BASE	:= include/plat/marvell/armada
+
+SEPARATE_CODE_AND_RODATA	:= 1
+
+# flag to switch from PLL to ARO
+ARO_ENABLE			:= 0
+$(eval $(call add_define,ARO_ENABLE))
+
+# Convert LLC to secure SRAM
+LLC_SRAM			:= 0
+$(eval $(call add_define,LLC_SRAM))
+
+# Enable/Disable LLC
+LLC_ENABLE			:= 1
+$(eval $(call add_define,LLC_ENABLE))
+
+include lib/xlat_tables_v2/xlat_tables.mk
+
+PLAT_INCLUDES		+=	-I$(MARVELL_PLAT_INCLUDE_BASE)/common	\
+				-I$(MARVELL_PLAT_INCLUDE_BASE)/common/aarch64
+
+
+PLAT_BL_COMMON_SOURCES  += ${XLAT_TABLES_LIB_SRCS} \
+				$(MARVELL_PLAT_BASE)/common/aarch64/marvell_common.c	\
+				$(MARVELL_PLAT_BASE)/common/aarch64/marvell_helpers.S	\
+				$(MARVELL_COMMON_BASE)/marvell_console.c
+
+BL1_SOURCES		+=	drivers/delay_timer/delay_timer.c			\
+				drivers/io/io_fip.c					\
+				drivers/io/io_memmap.c					\
+				drivers/io/io_storage.c					\
+				$(MARVELL_PLAT_BASE)/common/marvell_bl1_setup.c		\
+				$(MARVELL_PLAT_BASE)/common/marvell_io_storage.c	\
+				$(MARVELL_PLAT_BASE)/common/plat_delay_timer.c
+
+ifdef EL3_PAYLOAD_BASE
+# Need the arm_program_trusted_mailbox() function to release secondary CPUs from
+# their holding pen
+endif
+
+BL2_SOURCES		+=	drivers/io/io_fip.c					\
+				drivers/io/io_memmap.c					\
+				drivers/io/io_storage.c					\
+				common/desc_image_load.c				\
+				$(MARVELL_PLAT_BASE)/common/marvell_bl2_setup.c		\
+				$(MARVELL_PLAT_BASE)/common/marvell_io_storage.c	\
+				$(MARVELL_PLAT_BASE)/common/aarch64/marvell_bl2_mem_params_desc.c	\
+				$(MARVELL_PLAT_BASE)/common/marvell_image_load.c
+
+ifeq (${SPD},opteed)
+PLAT_INCLUDES		+=	-Iinclude/lib
+BL2_SOURCES		+=	lib/optee/optee_utils.c
+endif
+
+BL31_SOURCES		+=	$(MARVELL_PLAT_BASE)/common/marvell_bl31_setup.c	\
+				$(MARVELL_PLAT_BASE)/common/marvell_pm.c		\
+				$(MARVELL_PLAT_BASE)/common/marvell_topology.c		\
+				plat/common/plat_psci_common.c				\
+				$(MARVELL_PLAT_BASE)/common/plat_delay_timer.c		\
+				drivers/delay_timer/delay_timer.c
+
+# PSCI functionality
+$(eval $(call add_define,CONFIG_ARM64))
+
+# Add the build options to pack Trusted OS Extra1 and Trusted OS Extra2 images
+# in the FIP if the platform requires.
+ifneq ($(BL32_EXTRA1),)
+$(eval $(call TOOL_ADD_IMG,bl32_extra1,--tos-fw-extra1))
+endif
+ifneq ($(BL32_EXTRA2),)
+$(eval $(call TOOL_ADD_IMG,bl32_extra2,--tos-fw-extra2))
+endif
+
+# MSS (SCP) build
+ifeq (${MSS_SUPPORT}, 1)
+include $(MARVELL_PLAT_BASE)/common/mss/mss_common.mk
+endif
+
+$(BUILD_PLAT)/$(BOOT_IMAGE): $(BUILD_PLAT)/bl1.bin $(BUILD_PLAT)/$(FIP_NAME)
+	$(if $(shell find $(BUILD_PLAT)/bl1.bin -type f -size +128k),$(error "Image '$(BUILD_PLAT)/bl1.bin' is bigger than 128kB"))
+	@cp $(BUILD_PLAT)/bl1.bin $(BUILD_PLAT)/$(BOOT_IMAGE) || { rm -f $(BUILD_PLAT)/$(BOOT_IMAGE); false; }
+	@truncate -s %128K $(BUILD_PLAT)/$(BOOT_IMAGE) || { rm -f $(BUILD_PLAT)/$(BOOT_IMAGE); false; }
+	@cat $(BUILD_PLAT)/$(FIP_NAME) >> $(BUILD_PLAT)/$(BOOT_IMAGE) || { rm -f $(BUILD_PLAT)/$(BOOT_IMAGE); false; }
+	@truncate -s %4 $(BUILD_PLAT)/$(BOOT_IMAGE) || { rm -f $(BUILD_PLAT)/$(BOOT_IMAGE); false; }
+	@$(ECHO_BLANK_LINE)
+	@echo "Built $@ successfully"
+	@$(ECHO_BLANK_LINE)
+
+.PHONY: mrvl_bootimage
+mrvl_bootimage: $(BUILD_PLAT)/$(BOOT_IMAGE)
+
+.PHONY: mrvl_flash
+mrvl_flash: $(BUILD_PLAT)/$(FLASH_IMAGE)
diff --git a/plat/marvell/armada/common/marvell_console.c b/plat/marvell/armada/common/marvell_console.c
new file mode 100644
index 0000000..ef54bff
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_console.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (c) 2018-2020, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+#include <assert.h>
+
+#include <platform_def.h>
+
+#include <common/debug.h>
+#include <drivers/console.h>
+
+#include <plat_marvell.h>
+
+#ifdef PLAT_a3700
+#include <drivers/marvell/uart/a3700_console.h>
+#define PLAT_MARVELL_UART_CLK_IN_HZ (get_ref_clk() * 1000000)
+#define console_marvell_register console_a3700_register
+#else
+#include <drivers/ti/uart/uart_16550.h>
+#define console_marvell_register console_16550_register
+#endif
+
+static console_t marvell_boot_console;
+static console_t marvell_runtime_console;
+
+/*******************************************************************************
+ * Functions that set up the console
+ ******************************************************************************/
+
+/* Initialize the console to provide early debug support */
+void marvell_console_boot_init(void)
+{
+	int rc =
+	console_marvell_register(PLAT_MARVELL_UART_BASE,
+				 PLAT_MARVELL_UART_CLK_IN_HZ,
+				 MARVELL_CONSOLE_BAUDRATE,
+				 &marvell_boot_console);
+	if (rc == 0) {
+		/*
+		 * The crash console doesn't use the multi console API, it uses
+		 * the core console functions directly. It is safe to call panic
+		 * and let it print debug information.
+		 */
+		panic();
+	}
+
+	console_set_scope(&marvell_boot_console, CONSOLE_FLAG_BOOT);
+}
+
+void marvell_console_boot_end(void)
+{
+	console_flush();
+
+	(void)console_unregister(&marvell_boot_console);
+}
+
+/* Initialize the runtime console */
+void marvell_console_runtime_init(void)
+{
+	int rc =
+	console_marvell_register(PLAT_MARVELL_UART_BASE,
+				 PLAT_MARVELL_UART_CLK_IN_HZ,
+				 MARVELL_CONSOLE_BAUDRATE,
+				 &marvell_runtime_console);
+	if (rc == 0)
+		panic();
+
+	console_set_scope(&marvell_runtime_console, CONSOLE_FLAG_RUNTIME);
+}
+
+void marvell_console_runtime_end(void)
+{
+	console_flush();
+
+	(void)console_unregister(&marvell_runtime_console);
+}
diff --git a/plat/marvell/armada/common/marvell_ddr_info.c b/plat/marvell/armada/common/marvell_ddr_info.c
new file mode 100644
index 0000000..1ae0254
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_ddr_info.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+#include <common/debug.h>
+#include <lib/mmio.h>
+
+#include <ddr_info.h>
+
+#define DRAM_CH0_MMAP_LOW_REG(iface, cs, base)	\
+	(base + DRAM_CH0_MMAP_LOW_OFFSET + (iface) * 0x10000 + (cs) * 0x8)
+#define DRAM_CH0_MMAP_HIGH_REG(iface, cs, base)	\
+	(DRAM_CH0_MMAP_LOW_REG(iface, cs, base) + 4)
+#define DRAM_CS_VALID_ENABLED_MASK		0x1
+#define DRAM_AREA_LENGTH_OFFS			16
+#define DRAM_AREA_LENGTH_MASK			(0x1f << DRAM_AREA_LENGTH_OFFS)
+#define DRAM_START_ADDRESS_L_OFFS		23
+#define DRAM_START_ADDRESS_L_MASK		\
+					(0x1ff << DRAM_START_ADDRESS_L_OFFS)
+#define DRAM_START_ADDR_HTOL_OFFS		32
+
+#define DRAM_MAX_CS_NUM				2
+
+#define DRAM_CS_ENABLED(iface, cs, base) \
+	(mmio_read_32(DRAM_CH0_MMAP_LOW_REG(iface, cs, base)) & \
+	 DRAM_CS_VALID_ENABLED_MASK)
+#define GET_DRAM_REGION_SIZE_CODE(iface, cs, base) \
+	(mmio_read_32(DRAM_CH0_MMAP_LOW_REG(iface, cs, base)) & \
+	DRAM_AREA_LENGTH_MASK) >> DRAM_AREA_LENGTH_OFFS
+
+/* Mapping between DDR area length and real DDR size is specific and looks like
+ * below:
+ * 0 => 384 MB
+ * 1 => 768 MB
+ * 2 => 1536 MB
+ * 3 => 3 GB
+ * 4 => 6 GB
+ *
+ * 7 => 8 MB
+ * 8 => 16 MB
+ * 9 => 32 MB
+ * 10 => 64 MB
+ * 11 => 128 MB
+ * 12 => 256 MB
+ * 13 => 512 MB
+ * 14 => 1 GB
+ * 15 => 2 GB
+ * 16 => 4 GB
+ * 17 => 8 GB
+ * 18 => 16 GB
+ * 19 => 32 GB
+ * 20 => 64 GB
+ * 21 => 128 GB
+ * 22 => 256 GB
+ * 23 => 512 GB
+ * 24 => 1 TB
+ * 25 => 2 TB
+ * 26 => 4 TB
+ *
+ * to calculate real size we need to use two different formulas:
+ * -- GET_DRAM_REGION_SIZE_ODD for values 0-4 (DRAM_REGION_SIZE_ODD)
+ * -- GET_DRAM_REGION_SIZE_EVEN for values 7-26 (DRAM_REGION_SIZE_EVEN)
+ * using mentioned formulas we cover whole mapping between "Area length" value
+ * and real size (see above mapping).
+ */
+#define DRAM_REGION_SIZE_EVEN(C)	(((C) >= 7) && ((C) <= 26))
+#define GET_DRAM_REGION_SIZE_EVEN(C)	((uint64_t)1 << ((C) + 16))
+#define DRAM_REGION_SIZE_ODD(C)		((C) <= 4)
+#define GET_DRAM_REGION_SIZE_ODD(C)	((uint64_t)0x18000000 << (C))
+
+
+uint64_t mvebu_get_dram_size(uint64_t ap_base_addr)
+{
+	uint64_t mem_size = 0;
+	uint8_t region_code;
+	uint8_t cs, iface;
+
+	for (iface = 0; iface < DRAM_MAX_IFACE; iface++) {
+		for (cs = 0; cs < DRAM_MAX_CS_NUM; cs++) {
+
+			/* Exit loop on first disabled DRAM CS */
+			if (!DRAM_CS_ENABLED(iface, cs, ap_base_addr))
+				break;
+
+			/* Decode area length for current CS
+			 * from register value
+			 */
+			region_code =
+				GET_DRAM_REGION_SIZE_CODE(iface, cs,
+							  ap_base_addr);
+
+			if (DRAM_REGION_SIZE_EVEN(region_code)) {
+				mem_size +=
+					GET_DRAM_REGION_SIZE_EVEN(region_code);
+			} else if (DRAM_REGION_SIZE_ODD(region_code)) {
+				mem_size +=
+					GET_DRAM_REGION_SIZE_ODD(region_code);
+			} else {
+				WARN("%s: Invalid mem region (0x%x) CS#%d\n",
+				      __func__, region_code, cs);
+				return 0;
+			}
+		}
+	}
+
+	return mem_size;
+}
diff --git a/plat/marvell/armada/common/marvell_gicv2.c b/plat/marvell/armada/common/marvell_gicv2.c
new file mode 100644
index 0000000..2505c9f
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_gicv2.c
@@ -0,0 +1,148 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+#include <bl31/interrupt_mgmt.h>
+#include <common/debug.h>
+#include <drivers/arm/gicv2.h>
+#include <lib/bakery_lock.h>
+#include <lib/mmio.h>
+#include <plat/common/platform.h>
+
+#include <plat_marvell.h>
+
+/*
+ * The following functions are defined as weak to allow a platform to override
+ * the way the GICv2 driver is initialised and used.
+ */
+#pragma weak plat_marvell_gic_driver_init
+#pragma weak plat_marvell_gic_init
+
+#define A7K8K_PIC_CAUSE_REG		0xf03f0100
+#define A7K8K_PIC0_MASK_REG		0xf03f0108
+
+#define A7K8K_PIC_PMUOF_IRQ_MASK	(1 << 17)
+
+#define A7K8K_PIC_MAX_IRQS		32
+#define A7K8K_PIC_MAX_IRQ_MASK		((1UL << A7K8K_PIC_MAX_IRQS) - 1)
+
+#define A7K8K_ODMIN_SET_REG		0xf0300040
+#define A7K8K_ODMI_PMU_IRQ(idx)		((2 + idx) << 12)
+
+#define A7K8K_ODMI_PMU_GIC_IRQ(idx)	(130 + idx)
+
+static DEFINE_BAKERY_LOCK(a7k8k_irq_lock);
+
+/*
+ * On a GICv2 system, the Group 1 secure interrupts are treated as Group 0
+ * interrupts.
+ */
+static const interrupt_prop_t marvell_interrupt_props[] = {
+	PLAT_MARVELL_G1S_IRQ_PROPS(GICV2_INTR_GROUP0),
+	PLAT_MARVELL_G0_IRQ_PROPS(GICV2_INTR_GROUP0)
+};
+
+static unsigned int target_mask_array[PLATFORM_CORE_COUNT];
+
+/*
+ * Ideally `marvell_gic_data` structure definition should be a `const` but it is
+ * kept as modifiable for overwriting with different GICD and GICC base when
+ * running on FVP with VE memory map.
+ */
+static gicv2_driver_data_t marvell_gic_data = {
+	.gicd_base = PLAT_MARVELL_GICD_BASE,
+	.gicc_base = PLAT_MARVELL_GICC_BASE,
+	.interrupt_props = marvell_interrupt_props,
+	.interrupt_props_num = ARRAY_SIZE(marvell_interrupt_props),
+	.target_masks = target_mask_array,
+	.target_masks_num = ARRAY_SIZE(target_mask_array),
+};
+
+/*
+ * ARM common helper to initialize the GICv2 only driver.
+ */
+void plat_marvell_gic_driver_init(void)
+{
+	gicv2_driver_init(&marvell_gic_data);
+}
+
+static uint64_t a7k8k_pmu_interrupt_handler(uint32_t id,
+					  uint32_t flags,
+					  void *handle,
+					  void *cookie)
+{
+	unsigned int idx = plat_my_core_pos();
+	uint32_t irq;
+
+	bakery_lock_get(&a7k8k_irq_lock);
+
+	/* Acknowledge IRQ */
+	irq = plat_ic_acknowledge_interrupt();
+
+	plat_ic_end_of_interrupt(irq);
+
+	if (irq != MARVELL_IRQ_PIC0) {
+		bakery_lock_release(&a7k8k_irq_lock);
+		return 0;
+	}
+
+	/* Acknowledge PMU overflow IRQ in PIC0 */
+	mmio_setbits_32(A7K8K_PIC_CAUSE_REG, A7K8K_PIC_PMUOF_IRQ_MASK);
+
+	/* Trigger ODMI Frame IRQ */
+	mmio_write_32(A7K8K_ODMIN_SET_REG, A7K8K_ODMI_PMU_IRQ(idx));
+
+	bakery_lock_release(&a7k8k_irq_lock);
+
+	return 0;
+}
+
+void mvebu_pmu_interrupt_enable(void)
+{
+	unsigned int idx;
+	uint32_t flags;
+	int32_t rc;
+
+	/* Reset PIC */
+	mmio_write_32(A7K8K_PIC_CAUSE_REG, A7K8K_PIC_MAX_IRQ_MASK);
+	/* Unmask PMU overflow IRQ in PIC0 */
+	mmio_clrbits_32(A7K8K_PIC0_MASK_REG, A7K8K_PIC_PMUOF_IRQ_MASK);
+
+	/* Configure ODMI Frame IRQs as edge triggered */
+	for (idx = 0; idx < PLATFORM_CORE_COUNT; idx++)
+		gicv2_interrupt_set_cfg(A7K8K_ODMI_PMU_GIC_IRQ(idx),
+					GIC_INTR_CFG_EDGE);
+
+	/*
+	 * Register IRQ handler as INTR_TYPE_S_EL1 as its the only valid type
+	 * for GICv2 in ARM-TF.
+	 */
+	flags = 0U;
+	set_interrupt_rm_flag((flags), (NON_SECURE));
+	rc = register_interrupt_type_handler(INTR_TYPE_S_EL1,
+					     a7k8k_pmu_interrupt_handler,
+					     flags);
+	if (rc != 0)
+		panic();
+}
+
+void mvebu_pmu_interrupt_disable(void)
+{
+	/* Reset PIC */
+	mmio_write_32(A7K8K_PIC_CAUSE_REG, A7K8K_PIC_MAX_IRQ_MASK);
+	/* Mask PMU overflow IRQ in PIC0 */
+	mmio_setbits_32(A7K8K_PIC0_MASK_REG, A7K8K_PIC_PMUOF_IRQ_MASK);
+}
+
+void plat_marvell_gic_init(void)
+{
+	gicv2_distif_init();
+	gicv2_pcpu_distif_init();
+	gicv2_set_pe_target_mask(plat_my_core_pos());
+	gicv2_cpuif_enable();
+}
diff --git a/plat/marvell/armada/common/marvell_gicv3.c b/plat/marvell/armada/common/marvell_gicv3.c
new file mode 100644
index 0000000..5419506
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_gicv3.c
@@ -0,0 +1,210 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <platform_def.h>
+
+#include <common/debug.h>
+#include <common/interrupt_props.h>
+#include <drivers/arm/gicv3.h>
+#include <plat/common/platform.h>
+
+#include <marvell_def.h>
+#include <plat_marvell.h>
+
+/******************************************************************************
+ * The following functions are defined as weak to allow a platform to override
+ * the way the GICv3 driver is initialised and used.
+ ******************************************************************************
+ */
+#pragma weak plat_marvell_gic_driver_init
+#pragma weak plat_marvell_gic_init
+#pragma weak plat_marvell_gic_cpuif_enable
+#pragma weak plat_marvell_gic_cpuif_disable
+#pragma weak plat_marvell_gic_pcpu_init
+
+/* The GICv3 driver only needs to be initialized in EL3 */
+static uintptr_t rdistif_base_addrs[PLATFORM_CORE_COUNT];
+
+static const interrupt_prop_t marvell_interrupt_props[] = {
+	PLAT_MARVELL_G1S_IRQ_PROPS(INTR_GROUP1S),
+	PLAT_MARVELL_G0_IRQ_PROPS(INTR_GROUP0)
+};
+
+/*
+ * We save and restore the GICv3 context on system suspend. Allocate the
+ * data in the designated EL3 Secure carve-out memory
+ */
+static gicv3_redist_ctx_t rdist_ctx __section(".arm_el3_tzc_dram");
+static gicv3_dist_ctx_t dist_ctx __section(".arm_el3_tzc_dram");
+
+/*
+ * MPIDR hashing function for translating MPIDRs read from GICR_TYPER register
+ * to core position.
+ *
+ * Calculating core position is dependent on MPIDR_EL1.MT bit. However, affinity
+ * values read from GICR_TYPER don't have an MT field. To reuse the same
+ * translation used for CPUs, we insert MT bit read from the PE's MPIDR into
+ * that read from GICR_TYPER.
+ *
+ * Assumptions:
+ *
+ *   - All CPUs implemented in the system have MPIDR_EL1.MT bit set;
+ *   - No CPUs implemented in the system use affinity level 3.
+ */
+static unsigned int marvell_gicv3_mpidr_hash(u_register_t mpidr)
+{
+	mpidr |= (read_mpidr_el1() & MPIDR_MT_MASK);
+	return plat_marvell_calc_core_pos(mpidr);
+}
+
+const gicv3_driver_data_t marvell_gic_data = {
+	.gicd_base = PLAT_MARVELL_GICD_BASE,
+	.gicr_base = PLAT_MARVELL_GICR_BASE,
+	.interrupt_props = marvell_interrupt_props,
+	.interrupt_props_num = ARRAY_SIZE(marvell_interrupt_props),
+	.rdistif_num = PLATFORM_CORE_COUNT,
+	.rdistif_base_addrs = rdistif_base_addrs,
+	.mpidr_to_core_pos = marvell_gicv3_mpidr_hash
+};
+
+void plat_marvell_gic_driver_init(void)
+{
+	/*
+	 * The GICv3 driver is initialized in EL3 and does not need
+	 * to be initialized again in SEL1. This is because the S-EL1
+	 * can use GIC system registers to manage interrupts and does
+	 * not need GIC interface base addresses to be configured.
+	 */
+#if IMAGE_BL31
+	gicv3_driver_init(&marvell_gic_data);
+#endif
+}
+
+/******************************************************************************
+ * Marvell common helper to initialize the GIC. Only invoked by BL31
+ ******************************************************************************
+ */
+void plat_marvell_gic_init(void)
+{
+	/* Initialize GIC-600 Multi Chip feature,
+	 * only if the maximum number of north bridges
+	 * is more than 1 - otherwise no need for multi
+	 * chip feature initialization
+	 */
+#if (PLAT_MARVELL_NORTHB_COUNT > 1)
+	if (gic600_multi_chip_init())
+		ERROR("GIC-600 Multi Chip initialization failed\n");
+#endif
+	gicv3_distif_init();
+	gicv3_rdistif_init(plat_my_core_pos());
+	gicv3_cpuif_enable(plat_my_core_pos());
+}
+
+/******************************************************************************
+ * Marvell common helper to enable the GIC CPU interface
+ ******************************************************************************
+ */
+void plat_marvell_gic_cpuif_enable(void)
+{
+	gicv3_cpuif_enable(plat_my_core_pos());
+}
+
+/******************************************************************************
+ * Marvell common helper to disable the GIC CPU interface
+ ******************************************************************************
+ */
+void plat_marvell_gic_cpuif_disable(void)
+{
+	gicv3_cpuif_disable(plat_my_core_pos());
+}
+
+/******************************************************************************
+ * Marvell common helper to init. the per-cpu redistributor interface in GICv3
+ ******************************************************************************
+ */
+void plat_marvell_gic_pcpu_init(void)
+{
+	gicv3_rdistif_init(plat_my_core_pos());
+}
+
+/******************************************************************************
+ * Marvell common helper to save SPI irq states in GICv3
+ ******************************************************************************
+ */
+void plat_marvell_gic_irq_save(void)
+{
+
+	/*
+	 * If an ITS is available, save its context before
+	 * the Redistributor using:
+	 * gicv3_its_save_disable(gits_base, &its_ctx[i])
+	 * Additionally, an implementation-defined sequence may
+	 * be required to save the whole ITS state.
+	 */
+
+	/*
+	 * Save the GIC Redistributors and ITS contexts before the
+	 * Distributor context. As we only handle SYSTEM SUSPEND API,
+	 * we only need to save the context of the CPU that is issuing
+	 * the SYSTEM SUSPEND call, i.e. the current CPU.
+	 */
+	gicv3_rdistif_save(plat_my_core_pos(), &rdist_ctx);
+
+	/* Save the GIC Distributor context */
+	gicv3_distif_save(&dist_ctx);
+
+	/*
+	 * From here, all the components of the GIC can be safely powered down
+	 * as long as there is an alternate way to handle wakeup interrupt
+	 * sources.
+	 */
+}
+
+/******************************************************************************
+ * Marvell common helper to restore SPI irq states in GICv3
+ ******************************************************************************
+ */
+void plat_marvell_gic_irq_restore(void)
+{
+	/* Restore the GIC Distributor context */
+	gicv3_distif_init_restore(&dist_ctx);
+
+	/*
+	 * Restore the GIC Redistributor and ITS contexts after the
+	 * Distributor context. As we only handle SYSTEM SUSPEND API,
+	 * we only need to restore the context of the CPU that issued
+	 * the SYSTEM SUSPEND call.
+	 */
+	gicv3_rdistif_init_restore(plat_my_core_pos(), &rdist_ctx);
+
+	/*
+	 * If an ITS is available, restore its context after
+	 * the Redistributor using:
+	 * gicv3_its_restore(gits_base, &its_ctx[i])
+	 * An implementation-defined sequence may be required to
+	 * restore the whole ITS state. The ITS must also be
+	 * re-enabled after this sequence has been executed.
+	 */
+}
+
+/******************************************************************************
+ * Marvell common helper to save per-cpu PPI irq states in GICv3
+ ******************************************************************************
+ */
+void plat_marvell_gic_irq_pcpu_save(void)
+{
+	gicv3_rdistif_save(plat_my_core_pos(), &rdist_ctx);
+}
+
+/******************************************************************************
+ * Marvell common helper to restore per-cpu PPI irq states in GICv3
+ ******************************************************************************
+ */
+void plat_marvell_gic_irq_pcpu_restore(void)
+{
+	gicv3_rdistif_init_restore(plat_my_core_pos(), &rdist_ctx);
+}
diff --git a/plat/marvell/armada/common/marvell_image_load.c b/plat/marvell/armada/common/marvell_image_load.c
new file mode 100644
index 0000000..be16b08
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_image_load.c
@@ -0,0 +1,36 @@
+/*
+ * Copyright (c) 2018, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <platform_def.h>
+
+#include <common/bl_common.h>
+#include <common/desc_image_load.h>
+#include <plat/common/platform.h>
+
+/*******************************************************************************
+ * This function flushes the data structures so that they are visible
+ * in memory for the next BL image.
+ ******************************************************************************/
+void plat_flush_next_bl_params(void)
+{
+	flush_bl_params_desc();
+}
+
+/*******************************************************************************
+ * This function returns the list of loadable images.
+ ******************************************************************************/
+bl_load_info_t *plat_get_bl_image_load_info(void)
+{
+	return get_bl_load_info_from_mem_params_desc();
+}
+
+/*******************************************************************************
+ * This function returns the list of executable images.
+ ******************************************************************************/
+bl_params_t *plat_get_next_bl_params(void)
+{
+	return get_next_bl_params_from_mem_params_desc();
+}
diff --git a/plat/marvell/armada/common/marvell_io_storage.c b/plat/marvell/armada/common/marvell_io_storage.c
new file mode 100644
index 0000000..2627ba4
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_io_storage.c
@@ -0,0 +1,227 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+#include <string.h>
+
+#include <platform_def.h>
+
+#include <common/bl_common.h>
+#include <common/debug.h>
+#include <drivers/io/io_driver.h>
+#include <drivers/io/io_fip.h>
+#include <drivers/io/io_memmap.h>
+#include <drivers/io/io_storage.h>
+#include <tools_share/firmware_image_package.h>
+
+/* IO devices */
+static const io_dev_connector_t *fip_dev_con;
+static uintptr_t fip_dev_handle;
+static const io_dev_connector_t *memmap_dev_con;
+static uintptr_t memmap_dev_handle;
+
+static const io_block_spec_t fip_block_spec = {
+	.offset = PLAT_MARVELL_FIP_BASE,
+	.length = PLAT_MARVELL_FIP_MAX_SIZE
+};
+
+static const io_uuid_spec_t bl2_uuid_spec = {
+	.uuid = UUID_TRUSTED_BOOT_FIRMWARE_BL2,
+};
+
+static const io_uuid_spec_t scp_bl2_uuid_spec = {
+	.uuid = UUID_SCP_FIRMWARE_SCP_BL2,
+};
+
+static const io_uuid_spec_t bl31_uuid_spec = {
+	.uuid = UUID_EL3_RUNTIME_FIRMWARE_BL31,
+};
+static const io_uuid_spec_t bl32_uuid_spec = {
+	.uuid = UUID_SECURE_PAYLOAD_BL32,
+};
+
+static const io_uuid_spec_t bl32_extra1_uuid_spec = {
+	.uuid = UUID_SECURE_PAYLOAD_BL32_EXTRA1,
+};
+
+static const io_uuid_spec_t bl32_extra2_uuid_spec = {
+	.uuid = UUID_SECURE_PAYLOAD_BL32_EXTRA2,
+};
+
+static const io_uuid_spec_t bl33_uuid_spec = {
+	.uuid = UUID_NON_TRUSTED_FIRMWARE_BL33,
+};
+
+static int open_fip(const uintptr_t spec);
+static int open_memmap(const uintptr_t spec);
+
+struct plat_io_policy {
+	uintptr_t *dev_handle;
+	uintptr_t image_spec;
+	int (*check)(const uintptr_t spec);
+};
+
+/* By default, Marvell platforms load images from the FIP */
+static const struct plat_io_policy policies[] = {
+	[FIP_IMAGE_ID] = {
+		&memmap_dev_handle,
+		(uintptr_t)&fip_block_spec,
+		open_memmap
+	},
+	[BL2_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&bl2_uuid_spec,
+		open_fip
+	},
+	[SCP_BL2_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&scp_bl2_uuid_spec,
+		open_fip
+	},
+	[BL31_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&bl31_uuid_spec,
+		open_fip
+	},
+	[BL32_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&bl32_uuid_spec,
+		open_fip
+	},
+	[BL32_EXTRA1_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&bl32_extra1_uuid_spec,
+		open_fip
+	},
+	[BL32_EXTRA2_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&bl32_extra2_uuid_spec,
+		open_fip
+	},
+	[BL33_IMAGE_ID] = {
+		&fip_dev_handle,
+		(uintptr_t)&bl33_uuid_spec,
+		open_fip
+	},
+};
+
+
+/* Weak definitions may be overridden in specific ARM standard platform */
+#pragma weak plat_marvell_io_setup
+#pragma weak plat_marvell_get_alt_image_source
+
+
+static int open_fip(const uintptr_t spec)
+{
+	int result;
+	uintptr_t local_image_handle;
+
+	/* See if a Firmware Image Package is available */
+	result = io_dev_init(fip_dev_handle, (uintptr_t)FIP_IMAGE_ID);
+	if (result == 0) {
+		result = io_open(fip_dev_handle, spec, &local_image_handle);
+		if (result == 0) {
+			VERBOSE("Using FIP\n");
+			io_close(local_image_handle);
+		}
+	}
+	return result;
+}
+
+
+static int open_memmap(const uintptr_t spec)
+{
+	int result;
+	uintptr_t local_image_handle;
+
+	result = io_dev_init(memmap_dev_handle, (uintptr_t)NULL);
+	if (result == 0) {
+		result = io_open(memmap_dev_handle, spec, &local_image_handle);
+		if (result == 0) {
+			VERBOSE("Using Memmap\n");
+			io_close(local_image_handle);
+		}
+	}
+	return result;
+}
+
+
+void marvell_io_setup(void)
+{
+	int io_result;
+
+	io_result = register_io_dev_fip(&fip_dev_con);
+	assert(io_result == 0);
+
+	io_result = register_io_dev_memmap(&memmap_dev_con);
+	assert(io_result == 0);
+
+	/* Open connections to devices and cache the handles */
+	io_result = io_dev_open(fip_dev_con, (uintptr_t)NULL,
+				&fip_dev_handle);
+	assert(io_result == 0);
+
+	io_result = io_dev_open(memmap_dev_con, (uintptr_t)NULL,
+				&memmap_dev_handle);
+	assert(io_result == 0);
+
+	/* Ignore improbable errors in release builds */
+	(void)io_result;
+}
+
+void plat_marvell_io_setup(void)
+{
+	marvell_io_setup();
+}
+
+int plat_marvell_get_alt_image_source(
+	unsigned int image_id __attribute__((unused)),
+	uintptr_t *dev_handle __attribute__((unused)),
+	uintptr_t *image_spec __attribute__((unused)))
+{
+	/* By default do not try an alternative */
+	return -ENOENT;
+}
+
+/*
+ * Return an IO device handle and specification which can be used to access
+ * an image. Use this to enforce platform load policy
+ */
+int plat_get_image_source(unsigned int image_id, uintptr_t *dev_handle,
+			  uintptr_t *image_spec)
+{
+	int result;
+	const struct plat_io_policy *policy;
+
+	assert(image_id < ARRAY_SIZE(policies));
+
+	policy = &policies[image_id];
+	result = policy->check(policy->image_spec);
+	if (result == 0) {
+		*image_spec = policy->image_spec;
+		*dev_handle = *(policy->dev_handle);
+	} else {
+		VERBOSE("Trying alternative IO\n");
+		result = plat_marvell_get_alt_image_source(image_id, dev_handle,
+						       image_spec);
+	}
+
+	return result;
+}
+
+/*
+ * See if a Firmware Image Package is available,
+ * by checking if TOC is valid or not.
+ */
+int marvell_io_is_toc_valid(void)
+{
+	int result;
+
+	result = io_dev_init(fip_dev_handle, (uintptr_t)FIP_IMAGE_ID);
+
+	return result == 0;
+}
diff --git a/plat/marvell/armada/common/marvell_pm.c b/plat/marvell/armada/common/marvell_pm.c
new file mode 100644
index 0000000..3c675b2
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_pm.c
@@ -0,0 +1,60 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+
+#include <arch_helpers.h>
+#include <lib/psci/psci.h>
+
+#include <marvell_pm.h>
+
+/* Standard ARM platforms are expected to export plat_arm_psci_pm_ops */
+extern const plat_psci_ops_t plat_arm_psci_pm_ops;
+
+/*****************************************************************************
+ * Private function to program the mailbox for a cpu before it is released
+ * from reset. This function assumes that the mail box base is within
+ * the MARVELL_SHARED_RAM region
+ *****************************************************************************
+ */
+void marvell_program_mailbox(uintptr_t address)
+{
+	uintptr_t *mailbox = (void *)PLAT_MARVELL_MAILBOX_BASE;
+
+	/*
+	 * Ensure that the PLAT_MARVELL_MAILBOX_BASE is within
+	 * MARVELL_SHARED_RAM region.
+	 */
+	assert((PLAT_MARVELL_MAILBOX_BASE >= MARVELL_SHARED_RAM_BASE) &&
+	       ((PLAT_MARVELL_MAILBOX_BASE + sizeof(*mailbox)) <=
+	       (MARVELL_SHARED_RAM_BASE + MARVELL_SHARED_RAM_SIZE)));
+
+	mailbox[MBOX_IDX_MAGIC] = MVEBU_MAILBOX_MAGIC_NUM;
+	mailbox[MBOX_IDX_SEC_ADDR] = address;
+
+	/* Flush data cache if the mail box shared RAM is cached */
+#if PLAT_MARVELL_SHARED_RAM_CACHED
+	flush_dcache_range((uintptr_t)PLAT_MARVELL_MAILBOX_BASE +
+			   8 * MBOX_IDX_MAGIC,
+			   2 * sizeof(uint64_t));
+#endif
+}
+
+/*****************************************************************************
+ * The ARM Standard platform definition of platform porting API
+ * `plat_setup_psci_ops`.
+ *****************************************************************************
+ */
+int plat_setup_psci_ops(uintptr_t sec_entrypoint,
+			const plat_psci_ops_t **psci_ops)
+{
+	*psci_ops = &plat_arm_psci_pm_ops;
+
+	/* Setup mailbox with entry point. */
+	marvell_program_mailbox(sec_entrypoint);
+	return 0;
+}
diff --git a/plat/marvell/armada/common/marvell_topology.c b/plat/marvell/armada/common/marvell_topology.c
new file mode 100644
index 0000000..a40ff6f
--- /dev/null
+++ b/plat/marvell/armada/common/marvell_topology.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <plat_marvell.h>
+
+/* The power domain tree descriptor */
+unsigned char marvell_power_domain_tree_desc[PLAT_MARVELL_CLUSTER_COUNT + 1];
+
+/*****************************************************************************
+ * This function dynamically constructs the topology according to
+ * PLAT_MARVELL_CLUSTER_COUNT and returns it.
+ *****************************************************************************
+ */
+const unsigned char *plat_get_power_domain_tree_desc(void)
+{
+	int i;
+
+	/*
+	 * The power domain tree does not have a single system level power
+	 * domain i.e. a single root node. The first entry in the power domain
+	 * descriptor specifies the number of power domains at the highest power
+	 * level.
+	 * For Marvell Platform this is the number of cluster power domains.
+	 */
+	marvell_power_domain_tree_desc[0] = PLAT_MARVELL_CLUSTER_COUNT;
+
+	for (i = 0; i < PLAT_MARVELL_CLUSTER_COUNT; i++)
+		marvell_power_domain_tree_desc[i + 1] =
+					PLAT_MARVELL_CLUSTER_CORE_COUNT;
+
+	return marvell_power_domain_tree_desc;
+}
+
+/*****************************************************************************
+ * This function validates an MPIDR by checking whether it falls within the
+ * acceptable bounds. An error code (-1) is returned if an incorrect mpidr
+ * is passed.
+ *****************************************************************************
+ */
+int marvell_check_mpidr(u_register_t mpidr)
+{
+	unsigned int nb_id, cluster_id, cpu_id;
+
+	mpidr &= MPIDR_AFFINITY_MASK;
+
+	if (mpidr & ~(MPIDR_CLUSTER_MASK | MPIDR_CPU_MASK |
+	    MPIDR_AFFLVL_MASK << MPIDR_AFF2_SHIFT))
+		return -1;
+
+	/* Get north bridge ID */
+	nb_id = MPIDR_AFFLVL3_VAL(mpidr);
+	cluster_id = MPIDR_AFFLVL1_VAL(mpidr);
+	cpu_id = MPIDR_AFFLVL0_VAL(mpidr);
+
+	if (nb_id >= PLAT_MARVELL_CLUSTER_COUNT)
+		return -1;
+
+	if (cluster_id >= PLAT_MARVELL_CLUSTER_COUNT)
+		return -1;
+
+	if (cpu_id >= PLAT_MARVELL_CLUSTER_CORE_COUNT)
+		return -1;
+
+	return 0;
+}
+
+/*****************************************************************************
+ * This function implements a part of the critical interface between the PSCI
+ * generic layer and the platform that allows the former to query the platform
+ * to convert an MPIDR to a unique linear index. An error code (-1) is returned
+ * in case the MPIDR is invalid.
+ *****************************************************************************
+ */
+int plat_core_pos_by_mpidr(u_register_t mpidr)
+{
+	if (marvell_check_mpidr(mpidr) == -1)
+		return -1;
+
+	return plat_marvell_calc_core_pos(mpidr);
+}
diff --git a/plat/marvell/armada/common/mrvl_sip_svc.c b/plat/marvell/armada/common/mrvl_sip_svc.c
new file mode 100644
index 0000000..c4c5c0e
--- /dev/null
+++ b/plat/marvell/armada/common/mrvl_sip_svc.c
@@ -0,0 +1,188 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <common/debug.h>
+#include <common/runtime_svc.h>
+#include <drivers/marvell/cache_llc.h>
+#include <drivers/marvell/mochi/ap_setup.h>
+#include <drivers/rambus/trng_ip_76.h>
+#include <lib/smccc.h>
+
+#include <marvell_plat_priv.h>
+#include <plat_marvell.h>
+
+#include "comphy/phy-comphy-cp110.h"
+#include "secure_dfx_access/dfx.h"
+#include "ddr_phy_access.h"
+#include <stdbool.h>
+
+/* #define DEBUG_COMPHY */
+#ifdef DEBUG_COMPHY
+#define debug(format...) NOTICE(format)
+#else
+#define debug(format, arg...)
+#endif
+
+/* Comphy related FID's */
+#define MV_SIP_COMPHY_POWER_ON	0x82000001
+#define MV_SIP_COMPHY_POWER_OFF	0x82000002
+#define MV_SIP_COMPHY_PLL_LOCK	0x82000003
+#define MV_SIP_COMPHY_XFI_TRAIN	0x82000004
+#define MV_SIP_COMPHY_DIG_RESET	0x82000005
+
+/* Miscellaneous FID's' */
+#define MV_SIP_DRAM_SIZE	0x82000010
+#define MV_SIP_LLC_ENABLE	0x82000011
+#define MV_SIP_PMU_IRQ_ENABLE	0x82000012
+#define MV_SIP_PMU_IRQ_DISABLE	0x82000013
+#define MV_SIP_DFX		0x82000014
+#define MV_SIP_DDR_PHY_WRITE	0x82000015
+#define MV_SIP_DDR_PHY_READ	0x82000016
+
+/* TRNG */
+#define MV_SIP_RNG_64		0xC200FF11
+
+#define MAX_LANE_NR		6
+#define MVEBU_COMPHY_OFFSET	0x441000
+#define MVEBU_CP_BASE_MASK	(~0xffffff)
+
+/* Common PHY register */
+#define COMPHY_TRX_TRAIN_CTRL_REG_0_OFFS	0x120a2c
+
+/* This macro is used to identify COMPHY related calls from SMC function ID */
+#define is_comphy_fid(fid)	\
+	((fid) >= MV_SIP_COMPHY_POWER_ON && (fid) <= MV_SIP_COMPHY_DIG_RESET)
+
+_Bool is_cp_range_valid(u_register_t *addr)
+{
+	int cp_nr;
+
+	*addr &= MVEBU_CP_BASE_MASK;
+	for (cp_nr = 0; cp_nr < CP_NUM; cp_nr++) {
+		if (*addr == MVEBU_CP_REGS_BASE(cp_nr))
+			return true;
+	}
+
+	return false;
+}
+
+uintptr_t mrvl_sip_smc_handler(uint32_t smc_fid,
+			       u_register_t x1,
+			       u_register_t x2,
+			       u_register_t x3,
+			       u_register_t x4,
+			       void *cookie,
+			       void *handle,
+			       u_register_t flags)
+{
+	u_register_t ret, read, x5 = x1;
+	int i;
+
+	debug("%s: got SMC (0x%x) x1 0x%lx, x2 0x%lx, x3 0x%lx\n",
+						 __func__, smc_fid, x1, x2, x3);
+
+	if (is_comphy_fid(smc_fid)) {
+		/* validate address passed via x1 */
+		if (!is_cp_range_valid(&x1)) {
+			ERROR("%s: Wrong smc (0x%x) address: %lx\n",
+			      __func__, smc_fid, x1);
+			SMC_RET1(handle, SMC_UNK);
+		}
+
+		x5 = x1 + COMPHY_TRX_TRAIN_CTRL_REG_0_OFFS;
+		x1 += MVEBU_COMPHY_OFFSET;
+
+		if (x2 >= MAX_LANE_NR) {
+			ERROR("%s: Wrong smc (0x%x) lane nr: %lx\n",
+			      __func__, smc_fid, x2);
+			SMC_RET1(handle, SMC_UNK);
+		}
+	}
+
+	switch (smc_fid) {
+
+	/* Comphy related FID's */
+	case MV_SIP_COMPHY_POWER_ON:
+		/* x1:  comphy_base, x2: comphy_index, x3: comphy_mode */
+		ret = mvebu_cp110_comphy_power_on(x1, x2, x3, x5);
+		SMC_RET1(handle, ret);
+	case MV_SIP_COMPHY_POWER_OFF:
+		/* x1:  comphy_base, x2: comphy_index */
+		ret = mvebu_cp110_comphy_power_off(x1, x2, x3);
+		SMC_RET1(handle, ret);
+	case MV_SIP_COMPHY_PLL_LOCK:
+		/* x1:  comphy_base, x2: comphy_index */
+		ret = mvebu_cp110_comphy_is_pll_locked(x1, x2);
+		SMC_RET1(handle, ret);
+	case MV_SIP_COMPHY_XFI_TRAIN:
+		/* x1:  comphy_base, x2: comphy_index */
+		ret = mvebu_cp110_comphy_xfi_rx_training(x1, x2);
+		SMC_RET1(handle, ret);
+	case MV_SIP_COMPHY_DIG_RESET:
+		/* x1:  comphy_base, x2: comphy_index, x3: mode, x4: command */
+		ret = mvebu_cp110_comphy_digital_reset(x1, x2, x3, x4);
+		SMC_RET1(handle, ret);
+
+	/* Miscellaneous FID's' */
+	case MV_SIP_DRAM_SIZE:
+		ret = mvebu_get_dram_size(MVEBU_REGS_BASE);
+		SMC_RET1(handle, ret);
+	case MV_SIP_LLC_ENABLE:
+		for (i = 0; i < ap_get_count(); i++)
+			llc_runtime_enable(i);
+
+		SMC_RET1(handle, 0);
+#ifdef MVEBU_PMU_IRQ_WA
+	case MV_SIP_PMU_IRQ_ENABLE:
+		mvebu_pmu_interrupt_enable();
+		SMC_RET1(handle, 0);
+	case MV_SIP_PMU_IRQ_DISABLE:
+		mvebu_pmu_interrupt_disable();
+		SMC_RET1(handle, 0);
+#endif
+	case MV_SIP_DFX:
+		if (x1 >= MV_SIP_DFX_THERMAL_INIT &&
+		    x1 <= MV_SIP_DFX_THERMAL_SEL_CHANNEL) {
+			ret = mvebu_dfx_thermal_handle(x1, &read, x2, x3);
+			SMC_RET2(handle, ret, read);
+		}
+		if (x1 >= MV_SIP_DFX_SREAD && x1 <= MV_SIP_DFX_SWRITE) {
+			ret = mvebu_dfx_misc_handle(x1, &read, x2, x3);
+			SMC_RET2(handle, ret, read);
+		}
+
+		SMC_RET1(handle, SMC_UNK);
+	case MV_SIP_DDR_PHY_WRITE:
+		ret = mvebu_ddr_phy_write(x1, x2);
+		SMC_RET1(handle, ret);
+	case MV_SIP_DDR_PHY_READ:
+		read = 0;
+		ret = mvebu_ddr_phy_read(x1, (uint16_t *)&read);
+		SMC_RET2(handle, ret, read);
+	case MV_SIP_RNG_64:
+		if ((x1 % 2 + 1) > sizeof(read)/4) {
+			ERROR("%s: Maximum %ld random bytes per SMC call\n",
+			      __func__, sizeof(read));
+			SMC_RET1(handle, SMC_UNK);
+		}
+		ret = eip76_rng_get_random((uint8_t *)&read, 4 * (x1 % 2 + 1));
+		SMC_RET2(handle, ret, read);
+	default:
+		ERROR("%s: unhandled SMC (0x%x)\n", __func__, smc_fid);
+		SMC_RET1(handle, SMC_UNK);
+	}
+}
+
+/* Define a runtime service descriptor for fast SMC calls */
+DECLARE_RT_SVC(
+	marvell_sip_svc,
+	OEN_SIP_START,
+	OEN_SIP_END,
+	SMC_TYPE_FAST,
+	NULL,
+	mrvl_sip_smc_handler
+);
diff --git a/plat/marvell/armada/common/mss/mss_common.mk b/plat/marvell/armada/common/mss/mss_common.mk
new file mode 100644
index 0000000..4ab4359
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_common.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+
+PLAT_MARVELL		:= 	plat/marvell/armada
+MSS_SOURCE		:= 	$(PLAT_MARVELL)/common/mss
+
+BL2_SOURCES		+=	$(MSS_SOURCE)/mss_scp_bootloader.c		\
+				$(PLAT_MARVELL)/common/plat_delay_timer.c	\
+				drivers/delay_timer/delay_timer.c		\
+				$(MARVELL_DRV)					\
+				$(BOARD_DIR)/board/marvell_plat_config.c
+
+BL31_SOURCES		+=	$(MSS_SOURCE)/mss_ipc_drv.c
+
+PLAT_INCLUDES           +=      -I$(MSS_SOURCE)
diff --git a/plat/marvell/armada/common/mss/mss_ipc_drv.c b/plat/marvell/armada/common/mss/mss_ipc_drv.c
new file mode 100644
index 0000000..70ccfa5
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_ipc_drv.c
@@ -0,0 +1,113 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <string.h>
+
+#include <common/debug.h>
+#include <lib/mmio.h>
+
+#include <plat_marvell.h>
+#include <mss_ipc_drv.h>
+
+#define IPC_MSG_BASE_MASK		MVEBU_REGS_BASE_MASK
+
+#define IPC_CH_NUM_OF_MSG		(16)
+#define IPC_CH_MSG_IDX			(-1)
+
+unsigned long mv_pm_ipc_msg_base;
+unsigned int  mv_pm_ipc_queue_size;
+
+unsigned int msg_sync;
+int msg_index = IPC_CH_MSG_IDX;
+
+/******************************************************************************
+ * mss_pm_ipc_init
+ *
+ * DESCRIPTION: Initialize PM IPC infrastructure
+ ******************************************************************************
+ */
+int mv_pm_ipc_init(unsigned long ipc_control_addr)
+{
+	struct mss_pm_ipc_ctrl *ipc_control =
+			(struct mss_pm_ipc_ctrl *)ipc_control_addr;
+
+	/* Initialize PM IPC control block */
+	mv_pm_ipc_msg_base     = ipc_control->msg_base_address |
+				 IPC_MSG_BASE_MASK;
+	mv_pm_ipc_queue_size   = ipc_control->queue_size;
+
+	return 0;
+}
+
+/******************************************************************************
+ * mv_pm_ipc_queue_addr_get
+ *
+ * DESCRIPTION: Returns the IPC queue address
+ ******************************************************************************
+ */
+unsigned int mv_pm_ipc_queue_addr_get(void)
+{
+	unsigned int addr;
+
+	inv_dcache_range((uint64_t)&msg_index, sizeof(msg_index));
+	msg_index = msg_index + 1;
+	if (msg_index >= IPC_CH_NUM_OF_MSG)
+		msg_index = 0;
+
+	addr = (unsigned int)(mv_pm_ipc_msg_base +
+	       (msg_index * mv_pm_ipc_queue_size));
+
+	flush_dcache_range((uint64_t)&msg_index, sizeof(msg_index));
+
+	return addr;
+}
+
+/******************************************************************************
+ * mv_pm_ipc_msg_rx
+ *
+ * DESCRIPTION: Retrieve message from IPC channel
+ ******************************************************************************
+ */
+int mv_pm_ipc_msg_rx(unsigned int channel_id, struct mss_pm_ipc_msg *msg)
+{
+	unsigned int addr = mv_pm_ipc_queue_addr_get();
+
+	msg->msg_reply = mmio_read_32(addr + IPC_MSG_REPLY_LOC);
+
+	return 0;
+}
+
+/******************************************************************************
+ * mv_pm_ipc_msg_tx
+ *
+ * DESCRIPTION: Send message via IPC channel
+ ******************************************************************************
+ */
+int mv_pm_ipc_msg_tx(unsigned int channel_id, unsigned int msg_id,
+					unsigned int cluster_power_state)
+{
+	unsigned int addr = mv_pm_ipc_queue_addr_get();
+
+	/* Validate the entry for message placed by the host is free */
+	if (mmio_read_32(addr + IPC_MSG_STATE_LOC) == IPC_MSG_FREE) {
+		inv_dcache_range((uint64_t)&msg_sync, sizeof(msg_sync));
+		msg_sync = msg_sync + 1;
+		flush_dcache_range((uint64_t)&msg_sync, sizeof(msg_sync));
+
+		mmio_write_32(addr + IPC_MSG_SYNC_ID_LOC, msg_sync);
+		mmio_write_32(addr + IPC_MSG_ID_LOC, msg_id);
+		mmio_write_32(addr + IPC_MSG_CPU_ID_LOC, channel_id);
+		mmio_write_32(addr + IPC_MSG_POWER_STATE_LOC,
+			      cluster_power_state);
+		mmio_write_32(addr + IPC_MSG_STATE_LOC, IPC_MSG_OCCUPY);
+
+	} else {
+		ERROR("%s: FAILED\n", __func__);
+	}
+
+	return 0;
+}
diff --git a/plat/marvell/armada/common/mss/mss_ipc_drv.h b/plat/marvell/armada/common/mss/mss_ipc_drv.h
new file mode 100644
index 0000000..bcb4b2d
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_ipc_drv.h
@@ -0,0 +1,120 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MSS_IPC_DRV_H
+#define MSS_IPC_DRV_H
+
+#include <lib/psci/psci.h>
+
+#define MV_PM_FW_IPC_VERSION_MAGIC	(0xCA530000) /* Do NOT change */
+/* Increament for each version */
+#define MV_PM_FW_IPC_VERSION_SEQ	(0x00000001)
+#define MV_PM_FW_IPC_VERSION		(MV_PM_FW_IPC_VERSION_MAGIC | \
+					 MV_PM_FW_IPC_VERSION_SEQ)
+
+#define IPC_MSG_STATE_LOC		(0x0)
+#define IPC_MSG_SYNC_ID_LOC		(0x4)
+#define IPC_MSG_ID_LOC			(0x8)
+#define IPC_MSG_RET_CH_ID_LOC	(0xC)
+#define IPC_MSG_CPU_ID_LOC		(0x10)
+#define IPC_MSG_CLUSTER_ID_LOC	(0x14)
+#define IPC_MSG_SYSTEM_ID_LOC	(0x18)
+#define IPC_MSG_POWER_STATE_LOC	(0x1C)
+#define IPC_MSG_REPLY_LOC		(0x20)
+#define IPC_MSG_RESERVED_LOC	(0x24)
+
+/* IPC initialization state */
+enum mss_pm_ipc_init_state {
+	IPC_UN_INITIALIZED	= 1,
+	IPC_INITIALIZED		= 2
+};
+
+/* IPC queue direction */
+enum mss_pm_ipc_init_msg_dir {
+	IPC_MSG_TX	= 0,
+	IPC_MSG_RX	= 1
+};
+
+/* IPC message state */
+enum mss_pm_ipc_msg_state {
+	IPC_MSG_FREE	= 1,
+	IPC_MSG_OCCUPY	= 2
+
+};
+
+/* IPC control block */
+struct mss_pm_ipc_ctrl {
+	unsigned int ctrl_base_address;
+	unsigned int msg_base_address;
+	unsigned int num_of_channels;
+	unsigned int channel_size;
+	unsigned int queue_size;
+};
+
+/* IPC message types */
+enum mss_pm_msg_id {
+	PM_IPC_MSG_CPU_SUSPEND		= 1,
+	PM_IPC_MSG_CPU_OFF		= 2,
+	PM_IPC_MSG_CPU_ON		= 3,
+	PM_IPC_MSG_SYSTEM_RESET		= 4,
+	PM_IPC_MSG_SYSTEM_SUSPEND	= 5,
+	PM_IPC_MAX_MSG
+};
+
+struct mss_pm_ipc_msg {
+	unsigned int	msg_sync_id;	/*
+					 * Sync number, validate message
+					 * reply corresponding to message
+					 * received
+					 */
+	unsigned int	msg_id;		/* Message Id */
+	unsigned int	ret_channel_id;	/* IPC channel reply */
+	unsigned int	cpu_id;		/* CPU Id */
+	unsigned int	cluster_id;	/* Cluster Id */
+	unsigned int	system_id;	/* System Id */
+	unsigned int	power_state;
+	unsigned int	msg_reply;	/* Message reply */
+};
+
+/* IPC queue */
+struct mss_pm_ipc_queue {
+	unsigned int	state;
+	struct mss_pm_ipc_msg		msg;
+};
+
+/* IPC channel */
+struct mss_pm_ipc_ch {
+	struct mss_pm_ipc_queue *tx_queue;
+	struct mss_pm_ipc_queue *rx_queue;
+};
+
+/*****************************************************************************
+ * mv_pm_ipc_init
+ *
+ * DESCRIPTION: Initialize PM IPC infrastructure
+ *****************************************************************************
+ */
+int mv_pm_ipc_init(unsigned long ipc_control_addr);
+
+/*****************************************************************************
+ * mv_pm_ipc_msg_rx
+ *
+ * DESCRIPTION: Retrieve message from IPC channel
+ *****************************************************************************
+ */
+int mv_pm_ipc_msg_rx(unsigned int channel_id, struct mss_pm_ipc_msg *msg);
+
+/*****************************************************************************
+ * mv_pm_ipc_msg_tx
+ *
+ * DESCRIPTION: Send message via IPC channel
+ *****************************************************************************
+ */
+int mv_pm_ipc_msg_tx(unsigned int channel_id, unsigned int msg_id,
+			unsigned int cluster_power_state);
+
+#endif /* MSS_IPC_DRV_H */
diff --git a/plat/marvell/armada/common/mss/mss_mem.h b/plat/marvell/armada/common/mss/mss_mem.h
new file mode 100644
index 0000000..5d68ac7
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_mem.h
@@ -0,0 +1,60 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MSS_MEM_H
+#define MSS_MEM_H
+
+/* MSS SRAM Memory base */
+#define MSS_SRAM_PM_CONTROL_BASE		(MVEBU_REGS_BASE + 0x520000)
+
+enum mss_pm_ctrl_handshake {
+	MSS_UN_INITIALIZED	= 0,
+	MSS_COMPATIBILITY_ERROR	= 1,
+	MSS_ACKNOWLEDGMENT	= 2,
+	HOST_ACKNOWLEDGMENT	= 3
+};
+
+enum mss_pm_ctrl_rtos_env {
+	MSS_MULTI_PROCESS_ENV	= 0,
+	MSS_SINGLE_PROCESS_ENV	= 1,
+	MSS_MAX_PROCESS_ENV
+};
+
+struct mss_pm_ctrl_block {
+	/* This field is used to synchronize the Host
+	 * and MSS initialization sequence
+	 * Valid Values
+	 * 0 - Un-Initialized
+	 * 1 - Compatibility Error
+	 * 2 - MSS Acknowledgment
+	 * 3 - Host Acknowledgment
+	 */
+	unsigned int handshake;
+
+	/*
+	 * This field include Host IPC version. Once received by the MSS
+	 * It will be compared to MSS IPC version and set MSS Acknowledge to
+	 * "compatibility error" in case there is no match
+	 */
+	unsigned int ipc_version;
+	unsigned int ipc_base_address;
+	unsigned int ipc_state;
+
+	/* Following fields defines firmware core architecture */
+	unsigned int num_of_cores;
+	unsigned int num_of_clusters;
+	unsigned int num_of_cores_per_cluster;
+
+	/* Following fields define pm trace debug base address */
+	unsigned int pm_trace_ctrl_base_address;
+	unsigned int pm_trace_info_base_address;
+	unsigned int pm_trace_info_core_size;
+
+	unsigned int ctrl_blk_size;
+};
+
+#endif /* MSS_MEM_H */
diff --git a/plat/marvell/armada/common/mss/mss_scp_bl2_format.h b/plat/marvell/armada/common/mss/mss_scp_bl2_format.h
new file mode 100644
index 0000000..90913b0
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_scp_bl2_format.h
@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MSS_SCP_BL2_FORMAT_H
+#define MSS_SCP_BL2_FORMAT_H
+
+#define MAX_NR_OF_FILES	8
+#define FILE_MAGIC	0xddd01ff
+#define HEADER_VERSION	0x1
+
+#define MSS_IDRAM_SIZE	0x10000 /* 64KB */
+#define MSS_SRAM_SIZE	0x8000 /* 32KB */
+
+/* Types definitions */
+typedef struct file_header {
+	/* Magic specific for concatenated file (used for validation) */
+	uint32_t magic;
+	uint32_t nr_of_imgs;	/* Number of images concatenated */
+} file_header_t;
+
+/* Types definitions */
+enum cm3_t {
+	MSS_AP,
+	MSS_CP0,
+	MSS_CP1,
+	MSS_CP2,
+	MSS_CP3,
+	MG_CP0,
+	MG_CP1,
+	MG_CP2,
+};
+
+typedef struct img_header {
+	uint32_t type;		/* CM3 type, can be one of cm3_t */
+	uint32_t length;	/* Image length */
+	uint32_t version;	/* For sanity checks and future
+				 * extended functionality
+				 */
+} img_header_t;
+
+#endif /* MSS_SCP_BL2_FORMAT_H */
diff --git a/plat/marvell/armada/common/mss/mss_scp_bootloader.c b/plat/marvell/armada/common/mss/mss_scp_bootloader.c
new file mode 100644
index 0000000..fbede1b
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_scp_bootloader.c
@@ -0,0 +1,368 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <assert.h>
+
+#include <platform_def.h>
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/delay_timer.h>
+#include <mg_conf_cm3/mg_conf_cm3.h>
+#include <lib/mmio.h>
+
+#include <plat_pm_trace.h>
+#include <mss_scp_bootloader.h>
+#include <mss_ipc_drv.h>
+#include <mss_mem.h>
+#include <mss_defs.h>
+#include <mss_scp_bl2_format.h>
+
+#define MSS_DMA_TIMEOUT			1000
+#define MSS_EXTERNAL_SPACE		0x50000000
+#define MSS_EXTERNAL_ADDR_MASK		0xfffffff
+#define MSS_INTERNAL_SPACE		0x40000000
+#define MSS_INTERNAL_ADDR_MASK		0x00ffffff
+
+#define DMA_SIZE			128
+
+#define MSS_HANDSHAKE_TIMEOUT		50
+
+static int mss_check_image_ready(volatile struct mss_pm_ctrl_block *mss_pm_crtl)
+{
+	int timeout = MSS_HANDSHAKE_TIMEOUT;
+
+	/* Wait for SCP to signal it's ready */
+	while ((mss_pm_crtl->handshake != MSS_ACKNOWLEDGMENT) &&
+						(timeout-- > 0))
+		mdelay(1);
+
+	if (mss_pm_crtl->handshake != MSS_ACKNOWLEDGMENT)
+		return -1;
+
+	mss_pm_crtl->handshake = HOST_ACKNOWLEDGMENT;
+
+	return 0;
+}
+
+static int mss_iram_dma_load(uint32_t src_addr, uint32_t size,
+			     uintptr_t mss_regs)
+{
+	uint32_t i, loop_num, timeout;
+
+	/* load image to MSS RAM using DMA */
+	loop_num = (size / DMA_SIZE) + !!(size % DMA_SIZE);
+	for (i = 0; i < loop_num; i++) {
+		/* write source address */
+		mmio_write_32(MSS_DMA_SRCBR(mss_regs),
+			      src_addr + (i * DMA_SIZE));
+		/* write destination address */
+		mmio_write_32(MSS_DMA_DSTBR(mss_regs), (i * DMA_SIZE));
+		/* make sure DMA data is ready before triggering it */
+		dsb();
+		/* set the DMA control register */
+		mmio_write_32(MSS_DMA_CTRLR(mss_regs),
+			      ((MSS_DMA_CTRLR_REQ_SET <<
+				MSS_DMA_CTRLR_REQ_OFFSET) |
+			      (DMA_SIZE << MSS_DMA_CTRLR_SIZE_OFFSET)));
+		/* Poll DMA_ACK at MSS_DMACTLR until it is ready */
+		timeout = MSS_DMA_TIMEOUT;
+		while (timeout > 0U) {
+			if (((mmio_read_32(MSS_DMA_CTRLR(mss_regs)) >>
+					  MSS_DMA_CTRLR_ACK_OFFSET) &
+					  MSS_DMA_CTRLR_ACK_MASK)
+					  == MSS_DMA_CTRLR_ACK_READY) {
+				break;
+			}
+			udelay(50);
+			timeout--;
+		}
+		if (timeout == 0) {
+			ERROR("\nMSS DMA failed (timeout)\n");
+			return 1;
+		}
+	}
+	return 0;
+}
+
+static int mss_image_load(uint32_t src_addr, uint32_t size,
+			  uintptr_t mss_regs, uintptr_t sram)
+{
+	uint32_t chunks = 1; /* !sram case */
+	uint32_t chunk_num;
+	int ret;
+
+	/* Check if the img size is not bigger than ID-RAM size of MSS CM3 */
+	if (size > MSS_IDRAM_SIZE) {
+		ERROR("image is too big to fit into MSS CM3 memory\n");
+		return 1;
+	}
+
+	/* The CPx MSS DMA cannot access DRAM directly in secure boot mode
+	 * Copy the MSS FW image to MSS SRAM by the CPU first, then run
+	 * MSS DMA for SRAM to IRAM copy
+	 */
+	if (sram != 0) {
+		chunks = size / MSS_SRAM_SIZE + !!(size % MSS_SRAM_SIZE);
+	}
+
+	NOTICE("%s Loading MSS FW from addr. 0x%x Size 0x%x to MSS at 0x%lx\n",
+	       sram == 0 ? "" : "SECURELY", src_addr, size, mss_regs);
+	for (chunk_num = 0; chunk_num < chunks; chunk_num++) {
+		size_t chunk_size = size;
+		uint32_t img_src = MSS_EXTERNAL_SPACE | /* no SRAM */
+				   (src_addr & MSS_EXTERNAL_ADDR_MASK);
+
+		if (sram != 0) {
+			uintptr_t chunk_source =
+				  src_addr + MSS_SRAM_SIZE * chunk_num;
+
+			if (chunk_num != (size / MSS_SRAM_SIZE)) {
+				chunk_size = MSS_SRAM_SIZE;
+			} else {
+				chunk_size =  size % MSS_SRAM_SIZE;
+			}
+
+			if (chunk_size == 0) {
+				break;
+			}
+
+			VERBOSE("Chunk %d -> SRAM 0x%lx from 0x%lx SZ 0x%lx\n",
+				chunk_num, sram, chunk_source, chunk_size);
+			memcpy((void *)sram, (void *)chunk_source, chunk_size);
+			dsb();
+			img_src = MSS_INTERNAL_SPACE |
+				  (sram & MSS_INTERNAL_ADDR_MASK);
+		}
+
+		ret = mss_iram_dma_load(img_src, chunk_size, mss_regs);
+		if (ret != 0) {
+			ERROR("MSS FW chunk %d load failed\n", chunk_num);
+			return ret;
+		}
+	}
+
+	bl2_plat_configure_mss_windows(mss_regs);
+
+	if (sram != 0) {
+		/* Wipe the MSS SRAM after using it as copy buffer */
+		memset((void *)sram, 0, MSS_SRAM_SIZE);
+		NOTICE("CP MSS startup is postponed\n");
+		/* FW loaded, but CPU startup postponed until final CP setup */
+		mmio_write_32(sram, MSS_FW_READY_MAGIC);
+		dsb();
+	} else {
+		/* Release M3 from reset */
+		mmio_write_32(MSS_M3_RSTCR(mss_regs),
+			      (MSS_M3_RSTCR_RST_OFF <<
+			       MSS_M3_RSTCR_RST_OFFSET));
+	}
+
+	NOTICE("Done\n");
+
+	return 0;
+}
+
+/* Load image to MSS AP and do PM related initialization
+ * Note that this routine is different than other CM3 loading routines, because
+ * firmware for AP is dedicated for PM and therefore some additional PM
+ * initialization is required
+ */
+static int mss_ap_load_image(uintptr_t single_img,
+			     uint32_t image_size, uint32_t ap_idx)
+{
+	volatile struct mss_pm_ctrl_block *mss_pm_crtl;
+	int ret;
+
+	/* TODO: add PM Control Info from platform */
+	mss_pm_crtl = (struct mss_pm_ctrl_block *)MSS_SRAM_PM_CONTROL_BASE;
+	mss_pm_crtl->ipc_version                = MV_PM_FW_IPC_VERSION;
+	mss_pm_crtl->num_of_clusters            = PLAT_MARVELL_CLUSTER_COUNT;
+	mss_pm_crtl->num_of_cores_per_cluster   =
+						PLAT_MARVELL_CLUSTER_CORE_COUNT;
+	mss_pm_crtl->num_of_cores               = PLAT_MARVELL_CLUSTER_COUNT *
+						PLAT_MARVELL_CLUSTER_CORE_COUNT;
+	mss_pm_crtl->pm_trace_ctrl_base_address = AP_MSS_ATF_CORE_CTRL_BASE;
+	mss_pm_crtl->pm_trace_info_base_address = AP_MSS_ATF_CORE_INFO_BASE;
+	mss_pm_crtl->pm_trace_info_core_size    = AP_MSS_ATF_CORE_INFO_SIZE;
+	VERBOSE("MSS Control Block = 0x%x\n", MSS_SRAM_PM_CONTROL_BASE);
+	VERBOSE("mss_pm_crtl->ipc_version                = 0x%x\n",
+		mss_pm_crtl->ipc_version);
+	VERBOSE("mss_pm_crtl->num_of_cores               = 0x%x\n",
+		mss_pm_crtl->num_of_cores);
+	VERBOSE("mss_pm_crtl->num_of_clusters            = 0x%x\n",
+		mss_pm_crtl->num_of_clusters);
+	VERBOSE("mss_pm_crtl->num_of_cores_per_cluster   = 0x%x\n",
+		mss_pm_crtl->num_of_cores_per_cluster);
+	VERBOSE("mss_pm_crtl->pm_trace_ctrl_base_address = 0x%x\n",
+		mss_pm_crtl->pm_trace_ctrl_base_address);
+	VERBOSE("mss_pm_crtl->pm_trace_info_base_address = 0x%x\n",
+		mss_pm_crtl->pm_trace_info_base_address);
+	VERBOSE("mss_pm_crtl->pm_trace_info_core_size    = 0x%x\n",
+		mss_pm_crtl->pm_trace_info_core_size);
+
+	/* TODO: add checksum to image */
+	VERBOSE("Send info about the SCP_BL2 image to be transferred to SCP\n");
+
+	ret = mss_image_load(single_img, image_size,
+			     bl2_plat_get_ap_mss_regs(ap_idx), 0);
+	if (ret != 0) {
+		ERROR("SCP Image load failed\n");
+		return -1;
+	}
+
+	/* check that the image was loaded successfully */
+	ret = mss_check_image_ready(mss_pm_crtl);
+	if (ret != 0)
+		NOTICE("SCP Image doesn't contain PM firmware\n");
+
+	return 0;
+}
+
+/* Load CM3 image (single_img) to CM3 pointed by cm3_type */
+static int load_img_to_cm3(enum cm3_t cm3_type,
+			   uintptr_t single_img, uint32_t image_size)
+{
+	int ret, ap_idx, cp_index;
+	uint32_t ap_count = bl2_plat_get_ap_count();
+
+	switch (cm3_type) {
+	case MSS_AP:
+		for (ap_idx = 0; ap_idx < ap_count; ap_idx++) {
+			NOTICE("Load image to AP%d MSS\n", ap_idx);
+			ret = mss_ap_load_image(single_img, image_size, ap_idx);
+			if (ret != 0)
+				return ret;
+		}
+		break;
+	case MSS_CP0:
+	case MSS_CP1:
+	case MSS_CP2:
+	case MSS_CP3:
+		/* MSS_AP = 0
+		 * MSS_CP1 = 1
+		 * .
+		 * .
+		 * MSS_CP3 = 4
+		 * Actual CP index is MSS_CPX - 1
+		 */
+		cp_index = cm3_type - 1;
+		for (ap_idx = 0; ap_idx < ap_count; ap_idx++) {
+			/* Check if we should load this image
+			 * according to number of CPs
+			 */
+			if (bl2_plat_get_cp_count(ap_idx) <= cp_index) {
+				NOTICE("Skipping MSS CP%d related image\n",
+				       cp_index);
+				break;
+			}
+
+			NOTICE("Load image to CP%d MSS AP%d\n",
+			       cp_index, ap_idx);
+			ret = mss_image_load(single_img, image_size,
+					     bl2_plat_get_cp_mss_regs(
+						     ap_idx, cp_index),
+					     bl2_plat_get_cp_mss_sram(
+						     ap_idx, cp_index));
+			if (ret != 0) {
+				ERROR("SCP Image load failed\n");
+				return -1;
+			}
+		}
+		break;
+	case MG_CP0:
+	case MG_CP1:
+	case MG_CP2:
+		cp_index = cm3_type - MG_CP0;
+		if (bl2_plat_get_cp_count(0) <= cp_index) {
+			NOTICE("Skipping MG CP%d related image\n",
+			       cp_index);
+			break;
+		}
+		NOTICE("Load image to CP%d MG\n", cp_index);
+		ret = mg_image_load(single_img, image_size, cp_index);
+		if (ret != 0) {
+			ERROR("SCP Image load failed\n");
+			return -1;
+		}
+		break;
+	default:
+		ERROR("SCP_BL2 wrong img format (cm3_type=%d)\n", cm3_type);
+		break;
+	}
+
+	return 0;
+}
+
+/* The Armada 8K has 5 service CPUs and Armada 7K has 3. Therefore it was
+ * required to provide a method for loading firmware to all of the service CPUs.
+ * To achieve that, the scp_bl2 image in fact is file containing up to 5
+ * concatenated firmwares and this routine splits concatenated image into single
+ * images dedicated for appropriate service CPU and then load them.
+ */
+static int split_and_load_bl2_image(void *image)
+{
+	file_header_t *file_hdr;
+	img_header_t *img_hdr;
+	uintptr_t single_img;
+	int i;
+
+	file_hdr = (file_header_t *)image;
+
+	if (file_hdr->magic != FILE_MAGIC) {
+		ERROR("SCP_BL2 wrong img format\n");
+		return -1;
+	}
+
+	if (file_hdr->nr_of_imgs > MAX_NR_OF_FILES) {
+		ERROR("SCP_BL2 concatenated image contains too many images\n");
+		return -1;
+	}
+
+	img_hdr = (img_header_t *)((uintptr_t)image + sizeof(file_header_t));
+	single_img = (uintptr_t)image + sizeof(file_header_t) +
+				    sizeof(img_header_t) * file_hdr->nr_of_imgs;
+
+	NOTICE("SCP_BL2 contains %d concatenated images\n",
+							  file_hdr->nr_of_imgs);
+	for (i = 0; i < file_hdr->nr_of_imgs; i++) {
+
+		/* Before loading make sanity check on header */
+		if (img_hdr->version != HEADER_VERSION) {
+			ERROR("Wrong header, img corrupted exiting\n");
+			return -1;
+		}
+
+		load_img_to_cm3(img_hdr->type, single_img, img_hdr->length);
+
+		/* Prepare offsets for next run */
+		single_img += img_hdr->length;
+		img_hdr++;
+	}
+
+	return 0;
+}
+
+int scp_bootloader_transfer(void *image, unsigned int image_size)
+{
+#ifdef SCP_BL2_BASE
+	assert((uintptr_t) image == SCP_BL2_BASE);
+#endif
+
+	VERBOSE("Concatenated img size %d\n", image_size);
+
+	if (image_size == 0) {
+		ERROR("SCP_BL2 image size can't be 0 (current size = 0x%x)\n",
+								    image_size);
+		return -1;
+	}
+
+	if (split_and_load_bl2_image(image))
+		return -1;
+
+	return 0;
+}
diff --git a/plat/marvell/armada/common/mss/mss_scp_bootloader.h b/plat/marvell/armada/common/mss/mss_scp_bootloader.h
new file mode 100644
index 0000000..d65354a
--- /dev/null
+++ b/plat/marvell/armada/common/mss/mss_scp_bootloader.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MSS_SCP_BOOTLOADER_H
+#define MSS_SCP_BOOTLOADER_H
+
+int scp_bootloader_transfer(void *image, unsigned int image_size);
+uintptr_t bl2_plat_get_cp_mss_regs(int ap_idx, int cp_idx);
+uintptr_t bl2_plat_get_cp_mss_sram(int ap_idx, int cp_idx);
+uintptr_t bl2_plat_get_ap_mss_regs(int ap_idx);
+uint32_t bl2_plat_get_cp_count(int ap_idx);
+uint32_t bl2_plat_get_ap_count(void);
+void bl2_plat_configure_mss_windows(uintptr_t mss_regs);
+int bl2_plat_mss_check_image_ready(void);
+
+#endif /* MSS_SCP_BOOTLOADER_H */
diff --git a/plat/marvell/armada/common/plat_delay_timer.c b/plat/marvell/armada/common/plat_delay_timer.c
new file mode 100644
index 0000000..2539752
--- /dev/null
+++ b/plat/marvell/armada/common/plat_delay_timer.c
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <drivers/delay_timer.h>
+
+#include <mvebu_def.h>
+
+#define SYS_COUNTER_FREQ_IN_MHZ	(COUNTER_FREQUENCY/1000000)
+
+static uint32_t plat_get_timer_value(void)
+{
+	/*
+	 * Generic delay timer implementation expects the timer to be a down
+	 * counter. We apply bitwise NOT operator to the tick values returned
+	 * by read_cntpct_el0() to simulate the down counter.
+	 */
+	return (uint32_t)(~read_cntpct_el0());
+}
+
+static const timer_ops_t plat_timer_ops = {
+	.get_timer_value	= plat_get_timer_value,
+	.clk_mult		= 1,
+	.clk_div		= SYS_COUNTER_FREQ_IN_MHZ
+};
+
+void plat_delay_timer_init(void)
+{
+	timer_init(&plat_timer_ops);
+}