Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 117 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt
new file mode 100644
index 0000000000..e7f502070d
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/imx-weim.txt
@@ -0,0 +1,117 @@
+Device tree bindings for i.MX Wireless External Interface Module (WEIM)
+
+The term "wireless" does not imply that the WEIM is literally an interface
+without wires. It simply means that this module was originally designed for
+wireless and mobile applications that use low-power technology.
+
+The actual devices are instantiated from the child nodes of a WEIM node.
+
+Required properties:
+
+ - compatible:		Should contain one of the following:
+			  "fsl,imx1-weim"
+			  "fsl,imx27-weim"
+			  "fsl,imx51-weim"
+			  "fsl,imx50-weim"
+			  "fsl,imx6q-weim"
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - clocks:		the clock, see the example below.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+Optional properties:
+
+ - fsl,weim-cs-gpr:	For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
+			devices, it should be the phandle to the system General
+			Purpose Register controller that contains WEIM CS GPR
+			register, e.g. IOMUXC_GPR1 on i.MX6Q.  IOMUXC_GPR1[11:0]
+			should be set up as one of the following 4 possible
+			values depending on the CS space configuration.
+
+			IOMUXC_GPR1[11:0]    CS0    CS1    CS2    CS3
+			---------------------------------------------
+				05	    128M     0M     0M     0M
+				033          64M    64M     0M     0M
+				0113         64M    32M    32M     0M
+				01111        32M    32M    32M    32M
+
+			In case that the property is absent, the reset value or
+			what bootloader sets up in IOMUXC_GPR1[11:0] will be
+			used.
+
+ - fsl,burst-clk-enable	For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
+			devices, the presence of this property indicates that
+			the weim bus should operate in Burst Clock Mode.
+
+ - fsl,continuous-burst-clk	Make Burst Clock to output continuous clock.
+			Without this option Burst Clock will output clock
+			only when necessary. This takes effect only if
+			"fsl,burst-clk-enable" is set.
+
+Timing property for child nodes. It is mandatory, not optional.
+
+ - fsl,weim-cs-timing:	The timing array, contains timing values for the
+			child node. We get the CS indexes from the address
+			ranges in the child node's "reg" property.
+			The number of registers depends on the selected chip:
+			For i.MX1, i.MX21 ("fsl,imx1-weim") there are two
+			registers: CSxU, CSxL.
+			For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim")
+			there are three registers: CSCRxU, CSCRxL, CSCRxA.
+			For i.MX50, i.MX53 ("fsl,imx50-weim"),
+			i.MX51 ("fsl,imx51-weim") and i.MX6Q ("fsl,imx6q-weim")
+			there are six registers: CSxGCR1, CSxGCR2, CSxRCR1,
+			CSxRCR2, CSxWCR1, CSxWCR2.
+
+Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
+
+	weim: weim@21b8000 {
+		compatible = "fsl,imx6q-weim";
+		reg = <0x021b8000 0x4000>;
+		clocks = <&clks 196>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x08000000>;
+		fsl,weim-cs-gpr = <&gpr>;
+
+		nor@0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x02000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+					0x0000c000 0x1404a38e 0x00000000>;
+		};
+	};
+
+Example for an imx6q-based board, a multi-chipselect device connected to WEIM:
+
+In this case, both chip select 0 and 1 will be configured with the same timing
+array values.
+
+	weim: weim@21b8000 {
+		compatible = "fsl,imx6q-weim";
+		reg = <0x021b8000 0x4000>;
+		clocks = <&clks 196>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x02000000
+			  1 0 0x0a000000 0x02000000
+			  2 0 0x0c000000 0x02000000
+			  3 0 0x0e000000 0x02000000>;
+		fsl,weim-cs-gpr = <&gpr>;
+
+		acme@0 {
+			compatible = "acme,whatever";
+			reg = <0 0 0x100>, <0 0x400000 0x800>,
+				<1 0x400000 0x800>;
+			fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
+				0x00000000 0xa0000240 0x00000000>;
+		};
+	};