Merging upstream version 6.8.9.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

16 files changed, 526 insertions, 180 deletions

diff --git a/Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.yaml b/Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.yaml
new file mode 100644
index 0000000000..5e86f6de69
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/adafruit,seesaw-gamepad.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/adafruit,seesaw-gamepad.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Adafruit Mini I2C Gamepad with seesaw
+
+maintainers:
+  - Anshul Dalal <anshulusr@gmail.com>
+
+description: |
+  Adafruit Mini I2C Gamepad
+
+    +-----------------------------+
+    |   ___                       |
+    |  /   \               (X)    |
+    | |  S  |  __   __  (Y)   (A) |
+    |  \___/  |ST| |SE|    (B)    |
+    |                             |
+    +-----------------------------+
+
+  S -> 10-bit precision bidirectional analog joystick
+  ST -> Start
+  SE -> Select
+  X, A, B, Y -> Digital action buttons
+
+  Datasheet: https://cdn-learn.adafruit.com/downloads/pdf/gamepad-qt.pdf
+  Product page: https://www.adafruit.com/product/5743
+  Arduino Driver: https://github.com/adafruit/Adafruit_Seesaw
+
+properties:
+  compatible:
+    const: adafruit,seesaw-gamepad
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+    description:
+      The gamepad's IRQ pin triggers a rising edge if interrupts are enabled.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        joystick@50 {
+            compatible = "adafruit,seesaw-gamepad";
+            interrupts = <18 IRQ_TYPE_EDGE_RISING>;
+            reg = <0x50>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/input/elan,ekth6915.yaml b/Documentation/devicetree/bindings/input/elan,ekth6915.yaml
index 3e2d216c64..dc4ac41f24 100644
--- a/Documentation/devicetree/bindings/input/elan,ekth6915.yaml
+++ b/Documentation/devicetree/bindings/input/elan,ekth6915.yaml
@@ -18,8 +18,9 @@ allOf:
 
 properties:
   compatible:
-    items:
-      - const: elan,ekth6915
+    enum:
+      - elan,ekth6915
+      - ilitek,ili2901
 
   reg:
     const: 0x10
diff --git a/Documentation/devicetree/bindings/input/gpio-keys.yaml b/Documentation/devicetree/bindings/input/gpio-keys.yaml
index 159cd9d9fe..cc78c21529 100644
--- a/Documentation/devicetree/bindings/input/gpio-keys.yaml
+++ b/Documentation/devicetree/bindings/input/gpio-keys.yaml
@@ -31,7 +31,23 @@ patternProperties:
         maxItems: 1
 
       interrupts:
-        maxItems: 1
+        oneOf:
+          - items:
+              - description: Optional key interrupt or wakeup interrupt
+          - items:
+              - description: Key interrupt
+              - description: Wakeup interrupt
+
+      interrupt-names:
+        description:
+          Optional interrupt names, can be used to specify a separate dedicated
+          wake-up interrupt in addition to the gpio irq
+        oneOf:
+          - items:
+              - enum: [ irq, wakeup ]
+          - items:
+              - const: irq
+              - const: wakeup
 
       label:
         description: Descriptive name of the key.
@@ -97,6 +113,20 @@ patternProperties:
       - required:
           - gpios
 
+    allOf:
+      - if:
+          properties:
+            interrupts:
+              minItems: 2
+          required:
+            - interrupts
+        then:
+          properties:
+            interrupt-names:
+              minItems: 2
+          required:
+            - interrupt-names
+
     dependencies:
       wakeup-event-action: [ wakeup-source ]
       linux,input-value: [ gpios ]
@@ -137,6 +167,15 @@ examples:
             linux,code = <108>;
             interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
         };
+
+        key-wakeup {
+            label = "GPIO Key WAKEUP";
+            linux,code = <143>;
+            interrupts-extended = <&intc 2 IRQ_TYPE_EDGE_FALLING>,
+                                  <&intc_wakeup 0 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "irq", "wakeup";
+            wakeup-source;
+        };
     };
 
 ...
diff --git a/Documentation/devicetree/bindings/input/gpio-mouse.txt b/Documentation/devicetree/bindings/input/gpio-mouse.txt
deleted file mode 100644
index 519510a11a..0000000000
--- a/Documentation/devicetree/bindings/input/gpio-mouse.txt
+++ /dev/null
@@ -1,32 +0,0 @@
-Device-Tree bindings for GPIO attached mice
-
-This simply uses standard GPIO handles to define a simple mouse connected
-to 5-7 GPIO lines.
-
-Required properties:
-	- compatible: must be "gpio-mouse"
-	- scan-interval-ms: The scanning interval in milliseconds
-	- up-gpios: GPIO line phandle to the line indicating "up"
-	- down-gpios: GPIO line phandle to the line indicating "down"
-	- left-gpios: GPIO line phandle to the line indicating "left"
-	- right-gpios: GPIO line phandle to the line indicating "right"
-
-Optional properties:
-	- button-left-gpios: GPIO line handle to the left mouse button
-	- button-middle-gpios: GPIO line handle to the middle mouse button
-	- button-right-gpios: GPIO line handle to the right mouse button
-Example:
-
-#include <dt-bindings/gpio/gpio.h>
-
-gpio-mouse {
-	compatible = "gpio-mouse";
-	scan-interval-ms = <50>;
-	up-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
-	down-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
-	left-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
-	right-gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
-	button-left-gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
-	button-middle-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
-	button-right-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
-};
diff --git a/Documentation/devicetree/bindings/input/gpio-mouse.yaml b/Documentation/devicetree/bindings/input/gpio-mouse.yaml
new file mode 100644
index 0000000000..3928ec6aff
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/gpio-mouse.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/gpio-mouse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GPIO attached mouse
+
+description: |
+  This simply uses standard GPIO handles to define a simple mouse connected
+  to 5-7 GPIO lines.
+
+maintainers:
+  - Anshul Dalal <anshulusr@gmail.com>
+
+properties:
+  compatible:
+    const: gpio-mouse
+
+  scan-interval-ms:
+    maxItems: 1
+
+  up-gpios:
+    maxItems: 1
+
+  down-gpios:
+    maxItems: 1
+
+  left-gpios:
+    maxItems: 1
+
+  right-gpios:
+    maxItems: 1
+
+  button-left-gpios:
+    maxItems: 1
+
+  button-middle-gpios:
+    maxItems: 1
+
+  button-right-gpios:
+    maxItems: 1
+
+required:
+  - compatible
+  - scan-interval-ms
+  - up-gpios
+  - down-gpios
+  - left-gpios
+  - right-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    gpio-mouse {
+        compatible = "gpio-mouse";
+        scan-interval-ms = <50>;
+        up-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+        down-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+        left-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+        right-gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+        button-left-gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+        button-middle-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+        button-right-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+    };
diff --git a/Documentation/devicetree/bindings/input/iqs269a.yaml b/Documentation/devicetree/bindings/input/iqs269a.yaml
index 3c430d3859..2c3f693b89 100644
--- a/Documentation/devicetree/bindings/input/iqs269a.yaml
+++ b/Documentation/devicetree/bindings/input/iqs269a.yaml
@@ -9,6 +9,9 @@ title: Azoteq IQS269A Capacitive Touch Controller
 maintainers:
   - Jeff LaBundy <jeff@labundy.com>
 
+allOf:
+  - $ref: input.yaml#
+
 description: |
   The Azoteq IQS269A is an 8-channel capacitive touch controller that features
   additional Hall-effect and inductive sensing capabilities.
@@ -17,7 +20,10 @@ description: |
 
 properties:
   compatible:
-    const: azoteq,iqs269a
+    enum:
+      - azoteq,iqs269a
+      - azoteq,iqs269a-00
+      - azoteq,iqs269a-d0
 
   reg:
     maxItems: 1
@@ -204,6 +210,73 @@ properties:
     default: 1
     description: Specifies the slider coordinate filter strength.
 
+  azoteq,touch-hold-ms:
+    multipleOf: 256
+    minimum: 256
+    maximum: 65280
+    default: 5120
+    description:
+      Specifies the length of time (in ms) for which the channel selected by
+      'azoteq,gpio3-select' must be held in a state of touch in order for an
+      approximately 60-ms pulse to be asserted on the GPIO4 pin.
+
+  linux,keycodes:
+    minItems: 1
+    maxItems: 8
+    description: |
+      Specifies the numeric keycodes associated with each available gesture in
+      the following order (enter 0 for unused gestures):
+      0: Slider 0 tap
+      1: Slider 0 hold
+      2: Slider 0 positive flick or swipe
+      3: Slider 0 negative flick or swipe
+      4: Slider 1 tap
+      5: Slider 1 hold
+      6: Slider 1 positive flick or swipe
+      7: Slider 1 negative flick or swipe
+
+  azoteq,gesture-swipe:
+    type: boolean
+    description:
+      Directs the device to interpret axial gestures as a swipe (finger remains
+      on slider) instead of a flick (finger leaves slider).
+
+  azoteq,timeout-tap-ms:
+    multipleOf: 16
+    minimum: 0
+    maximum: 4080
+    default: 400
+    description:
+      Specifies the length of time (in ms) within which a slider touch must be
+      released in order to be interpreted as a tap. Default and maximum values
+      as well as step size are reduced by a factor of 4 with device version 2.
+
+  azoteq,timeout-swipe-ms:
+    multipleOf: 16
+    minimum: 0
+    maximum: 4080
+    default: 2000
+    description:
+      Specifies the length of time (in ms) within which an axial gesture must be
+      completed in order to be interpreted as a flick or swipe. Default and max-
+      imum values as well as step size are reduced by a factor of 4 with device
+      version 2.
+
+  azoteq,thresh-swipe:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 255
+    default: 128
+    description:
+      Specifies the number of points across which an axial gesture must travel
+      in order to be interpreted as a flick or swipe.
+
+dependencies:
+  azoteq,gesture-swipe: ["linux,keycodes"]
+  azoteq,timeout-tap-ms: ["linux,keycodes"]
+  azoteq,timeout-swipe-ms: ["linux,keycodes"]
+  azoteq,thresh-swipe: ["linux,keycodes"]
+
 patternProperties:
   "^channel@[0-7]$":
     type: object
@@ -454,6 +527,21 @@ patternProperties:
 
     additionalProperties: false
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - azoteq,iqs269a-d0
+then:
+  patternProperties:
+    "^channel@[0-7]$":
+      properties:
+        azoteq,slider1-select: false
+else:
+  properties:
+    azoteq,touch-hold-ms: false
+
 required:
   - compatible
   - reg
@@ -484,6 +572,14 @@ examples:
                     azoteq,hall-enable;
                     azoteq,suspend-mode = <2>;
 
+                    linux,keycodes = <KEY_PLAYPAUSE>,
+                                     <KEY_STOPCD>,
+                                     <KEY_NEXTSONG>,
+                                     <KEY_PREVIOUSSONG>;
+
+                    azoteq,timeout-tap-ms = <400>;
+                    azoteq,timeout-swipe-ms = <800>;
+
                     channel@0 {
                             reg = <0x0>;
 
diff --git a/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml b/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml
index e34c9e78d3..70567d92c7 100644
--- a/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml
+++ b/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml
@@ -90,26 +90,4 @@ required:
 
 unevaluatedProperties: false
 
-examples:
-  - |
-    #include <dt-bindings/input/input.h>
-    #include <dt-bindings/interrupt-controller/arm-gic.h>
-
-    pmic {
-        compatible = "mediatek,mt6397";
-
-        keys {
-          compatible = "mediatek,mt6397-keys";
-          mediatek,long-press-mode = <1>;
-          power-off-time-sec = <0>;
-
-          key-power {
-            linux,keycodes = <KEY_POWER>;
-            wakeup-source;
-          };
-
-          key-home {
-            linux,keycodes = <KEY_VOLUMEDOWN>;
-          };
-        };
-    };
+...
diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
index 5b5d4f7d34..7ade03f1b3 100644
--- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -45,13 +45,13 @@ properties:
       Enables the Linux input system's autorepeat feature on the input device.
 
   linux,keycodes:
-    minItems: 6
-    maxItems: 6
+    minItems: 3
+    maxItems: 8
     description: |
       Specifies an array of numeric keycode values to
       be used for the channels. If this property is
       omitted, KEY_A, KEY_B, etc are used as defaults.
-      The array must have exactly six entries.
+      The number of entries must correspond to the number of channels.
 
   microchip,sensor-gain:
     $ref: /schemas/types.yaml#/definitions/uint32
@@ -70,6 +70,59 @@ properties:
       open drain. This property allows using the active
       high push-pull output.
 
+  microchip,sensitivity-delta-sense:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 32
+    enum: [1, 2, 4, 8, 16, 32, 64, 128]
+    description:
+      Controls the sensitivity multiplier of a touch detection.
+      Higher value means more sensitive settings.
+      At the more sensitive settings, touches are detected for a smaller delta
+      capacitance corresponding to a "lighter" touch.
+
+  microchip,signal-guard:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 8
+    items:
+      enum: [0, 1]
+    description: |
+      0 - off
+      1 - on
+      The signal guard isolates the signal from virtual grounds.
+      If enabled then the behavior of the channel is changed to signal guard.
+      The number of entries must correspond to the number of channels.
+
+  microchip,input-threshold:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 8
+    items:
+      minimum: 0
+      maximum: 127
+    description:
+      Specifies the delta threshold that is used to determine if a touch has
+      been detected. A higher value means a larger difference in capacitance
+      is required for a touch to be registered, making the touch sensor less
+      sensitive.
+      The number of entries must correspond to the number of channels.
+
+  microchip,calib-sensitivity:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 8
+    items:
+      enum: [1, 2, 4]
+    description: |
+      Specifies an array of numeric values that controls the gain
+      used by the calibration routine to enable sensor inputs
+      to be more sensitive for proximity detection.
+      Gain is based on touch pad capacitance range
+      1 - 5-50pF
+      2 - 0-25pF
+      4 - 0-12.5pF
+      The number of entries must correspond to the number of channels.
+
 patternProperties:
   "^led@[0-7]$":
     type: object
@@ -99,10 +152,29 @@ allOf:
           contains:
             enum:
               - microchip,cap1106
+              - microchip,cap1203
+              - microchip,cap1206
+              - microchip,cap1293
+              - microchip,cap1298
     then:
       patternProperties:
         "^led@[0-7]$": false
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - microchip,cap1106
+              - microchip,cap1126
+              - microchip,cap1188
+              - microchip,cap1203
+              - microchip,cap1206
+    then:
+      properties:
+        microchip,signal-guard: false
+        microchip,calib-sensitivity: false
+
 required:
   - compatible
   - interrupts
@@ -122,6 +194,8 @@ examples:
         reg = <0x28>;
         autorepeat;
         microchip,sensor-gain = <2>;
+        microchip,sensitivity-delta-sense = <16>;
+        microchip,input-threshold = <21>, <18>, <46>, <46>, <46>, <21>;
 
         linux,keycodes = <103>,	/* KEY_UP */
                          <106>,	/* KEY_RIGHT */
diff --git a/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml b/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml
index a401a0bfcb..4c8d303ff9 100644
--- a/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml
+++ b/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml
@@ -28,21 +28,4 @@ required:
 
 additionalProperties: false
 
-examples:
-  - |
-    #include <dt-bindings/interrupt-controller/arm-gic.h>
-    sc2731_pmic: pmic@0 {
-      compatible = "sprd,sc2731";
-      reg = <0 0>;
-      spi-max-frequency = <26000000>;
-      interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-      interrupt-controller;
-      #interrupt-cells = <2>;
-      #address-cells = <1>;
-      #size-cells = <0>;
-
-      vibrator@eb4 {
-        compatible = "sprd,sc2731-vibrator";
-        reg = <0xeb4>;
-      };
-    };
+...
diff --git a/Documentation/devicetree/bindings/input/ti,drv2665.txt b/Documentation/devicetree/bindings/input/ti,drv2665.txt
deleted file mode 100644
index 1ba97ac043..0000000000
--- a/Documentation/devicetree/bindings/input/ti,drv2665.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-* Texas Instruments - drv2665 Haptics driver
-
-Required properties:
-	- compatible - "ti,drv2665" - DRV2665
-	- reg -  I2C slave address
-	- vbat-supply - Required supply regulator
-
-Example:
-
-haptics: haptics@59 {
-	compatible = "ti,drv2665";
-	reg = <0x59>;
-	vbat-supply = <&vbat>;
-};
-
-For more product information please see the link below:
-http://www.ti.com/product/drv2665
diff --git a/Documentation/devicetree/bindings/input/ti,drv2667.txt b/Documentation/devicetree/bindings/input/ti,drv2667.txt
deleted file mode 100644
index 996382cf99..0000000000
--- a/Documentation/devicetree/bindings/input/ti,drv2667.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-* Texas Instruments - drv2667 Haptics driver
-
-Required properties:
-	- compatible - "ti,drv2667" - DRV2667
-	- reg -  I2C slave address
-	- vbat-supply - Required supply regulator
-
-Example:
-
-haptics: haptics@59 {
-	compatible = "ti,drv2667";
-	reg = <0x59>;
-	vbat-supply = <&vbat>;
-};
-
-For more product information please see the link below:
-http://www.ti.com/product/drv2667
diff --git a/Documentation/devicetree/bindings/input/ti,drv266x.yaml b/Documentation/devicetree/bindings/input/ti,drv266x.yaml
new file mode 100644
index 0000000000..da18188243
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/ti,drv266x.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/ti,drv266x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments - drv266x Haptics driver
+
+description: |
+  Product Page:
+    http://www.ti.com/product/drv2665
+    http://www.ti.com/product/drv2667
+
+maintainers:
+  - Anshul Dalal <anshulusr@gmail.com>
+
+properties:
+  compatible:
+    enum:
+      - ti,drv2665
+      - ti,drv2667
+
+  reg:
+    maxItems: 1
+
+  vbat-supply:
+    description: Required supply regulator
+
+required:
+  - compatible
+  - reg
+  - vbat-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        haptics@59 {
+            compatible = "ti,drv2667";
+            reg = <0x59>;
+            vbat-supply = <&vbat>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/neonode,zforce.yaml b/Documentation/devicetree/bindings/input/touchscreen/neonode,zforce.yaml
new file mode 100644
index 0000000000..c2ee89b76e
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/neonode,zforce.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/neonode,zforce.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Neonode infrared touchscreen controller
+
+maintainers:
+  - Heiko Stuebner <heiko@sntech.de>
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  compatible:
+    const: neonode,zforce
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  irq-gpios:
+    maxItems: 1
+
+  x-size:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  y-size:
+    deprecated: true
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  vdd-supply: true
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - reset-gpios
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        touchscreen@50 {
+            compatible = "neonode,zforce";
+            reg = <0x50>;
+            interrupts = <2 0>;
+            vdd-supply = <&reg_zforce_vdd>;
+
+            reset-gpios = <&gpio5 9 0>; /* RST */
+            irq-gpios = <&gpio5 6 0>; /* IRQ, optional */
+
+            touchscreen-min-x = <0>;
+            touchscreen-size-x = <800>;
+            touchscreen-min-y = <0>;
+            touchscreen-size-y = <600>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt
deleted file mode 100644
index 6805d10d22..0000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt
+++ /dev/null
@@ -1,32 +0,0 @@
-* Samsung S6SY761 touchscreen controller
-
-Required properties:
-- compatible		: must be "samsung,s6sy761"
-- reg			: I2C slave address, (e.g. 0x48)
-- interrupts		: interrupt specification
-- avdd-supply		: analogic power supply
-- vdd-supply		: power supply
-
-Optional properties:
-- touchscreen-size-x	: see touchscreen.txt. This property is embedded in the
-			  device. If defined it forces a different x resolution.
-- touchscreen-size-y	: see touchscreen.txt. This property is embedded in the
-			  device. If defined it forces a different y resolution.
-
-Example:
-
-i2c@00000000 {
-
-	/* ... */
-
-	touchscreen@48 {
-		compatible = "samsung,s6sy761";
-		reg = <0x48>;
-		interrupt-parent = <&gpa1>;
-		interrupts = <1 IRQ_TYPE_NONE>;
-		avdd-supply = <&ldo30_reg>;
-		vdd-supply = <&ldo31_reg>;
-		touchscreen-size-x = <4096>;
-		touchscreen-size-y = <4096>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.yaml b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.yaml
new file mode 100644
index 0000000000..1ffd17af3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/samsung,s6sy761.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S6SY761 touchscreen controller
+
+maintainers:
+  - Andi Shyti <andi.shyti@kernel.org>
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+properties:
+  compatible:
+    const: samsung,s6sy761
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  avdd-supply: true
+  vdd-supply: true
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - avdd-supply
+  - vdd-supply
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        touchscreen@48 {
+            compatible = "samsung,s6sy761";
+            reg = <0x48>;
+            interrupt-parent = <&gpa1>;
+            interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+            avdd-supply = <&ldo30_reg>;
+            vdd-supply = <&ldo31_reg>;
+            touchscreen-size-x = <4096>;
+            touchscreen-size-y = <4096>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt
deleted file mode 100644
index e3c27c4fd9..0000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt
+++ /dev/null
@@ -1,34 +0,0 @@
-* Neonode infrared touchscreen controller
-
-Required properties:
-- compatible: must be "neonode,zforce"
-- reg: I2C address of the chip
-- interrupts: interrupt to which the chip is connected
-- reset-gpios: reset gpio the chip is connected to
-- x-size: horizontal resolution of touchscreen
-- y-size: vertical resolution of touchscreen
-
-Optional properties:
-- irq-gpios : interrupt gpio the chip is connected to
-- vdd-supply: Regulator controlling the controller supply
-
-Example:
-
-	i2c@00000000 {
-		/* ... */
-
-		zforce_ts@50 {
-			compatible = "neonode,zforce";
-			reg = <0x50>;
-			interrupts = <2 0>;
-			vdd-supply = <&reg_zforce_vdd>;
-
-			reset-gpios = <&gpio5 9 0>; /* RST */
-			irq-gpios = <&gpio5 6 0>; /* IRQ, optional */
-
-			x-size = <800>;
-			y-size = <600>;
-		};
-
-		/* ... */
-	};