Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 164 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml
new file mode 100644
index 000000000..524f6fe8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml
@@ -0,0 +1,164 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SPI Controller Common Properties
+
+maintainers:
+  - Mark Brown <broonie@kernel.org>
+
+description: |
+  SPI busses can be described with a node for the SPI controller device
+  and a set of child nodes for each SPI slave on the bus. The system SPI
+  controller may be described for use in SPI master mode or in SPI slave mode,
+  but not for both at the same time.
+
+properties:
+  $nodename:
+    pattern: "^spi(@.*|-([0-9]|[1-9][0-9]+))?$"
+
+  "#address-cells":
+    enum: [0, 1]
+
+  "#size-cells":
+    const: 0
+
+  cs-gpios:
+    description: |
+      GPIOs used as chip selects.
+      If that property is used, the number of chip selects will be
+      increased automatically with max(cs-gpios, hardware chip selects).
+
+      So if, for example, the controller has 4 CS lines, and the
+      cs-gpios looks like this
+        cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
+
+      Then it should be configured so that num_chipselect = 4, with
+      the following mapping
+        cs0 : &gpio1 0 0
+        cs1 : native
+        cs2 : &gpio1 1 0
+        cs3 : &gpio1 2 0
+
+      The second flag of a gpio descriptor can be GPIO_ACTIVE_HIGH (0)
+      or GPIO_ACTIVE_LOW(1). Legacy device trees often use 0.
+
+      There is a special rule set for combining the second flag of an
+      cs-gpio with the optional spi-cs-high flag for SPI slaves.
+
+      Each table entry defines how the CS pin is to be physically
+      driven (not considering potential gpio inversions by pinmux):
+
+      device node     | cs-gpio       | CS pin state active | Note
+      ================+===============+=====================+=====
+      spi-cs-high     | -             | H                   |
+      -               | -             | L                   |
+      spi-cs-high     | ACTIVE_HIGH   | H                   |
+      -               | ACTIVE_HIGH   | L                   | 1
+      spi-cs-high     | ACTIVE_LOW    | H                   | 2
+      -               | ACTIVE_LOW    | L                   |
+
+      Notes:
+      1) Should print a warning about polarity inversion.
+         Here it would be wise to avoid and define the gpio as
+         ACTIVE_LOW.
+      2) Should print a warning about polarity inversion
+         because ACTIVE_LOW is overridden by spi-cs-high.
+         Should be generally avoided and be replaced by
+         spi-cs-high + ACTIVE_HIGH.
+
+  num-cs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Total number of chip selects.
+
+  spi-slave:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The SPI controller acts as a slave, instead of a master.
+
+  slave:
+    type: object
+
+    properties:
+      compatible:
+        description:
+          Compatible of the SPI device.
+
+    required:
+      - compatible
+
+patternProperties:
+  "^.*@[0-9a-f]+$":
+    type: object
+    $ref: spi-peripheral-props.yaml
+    additionalProperties: true
+
+    properties:
+      spi-3wire:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires 3-wire mode.
+
+      spi-cpha:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires shifted clock phase (CPHA) mode.
+
+      spi-cpol:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires inverse clock polarity (CPOL) mode.
+
+    required:
+      - compatible
+      - reg
+
+allOf:
+  - if:
+      not:
+        required:
+          - spi-slave
+    then:
+      properties:
+        "#address-cells":
+          const: 1
+    else:
+      properties:
+        "#address-cells":
+          const: 0
+
+additionalProperties: true
+
+examples:
+  - |
+    spi@80010000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "fsl,imx28-spi";
+        reg = <0x80010000 0x2000>;
+        interrupts = <96>;
+        dmas = <&dma_apbh 0>;
+        dma-names = "rx-tx";
+
+        display@0 {
+            compatible = "lg,lg4573";
+            spi-max-frequency = <1000000>;
+            reg = <0>;
+        };
+
+        sensor@1 {
+            compatible = "bosch,bme680";
+            spi-max-frequency = <100000>;
+            reg = <1>;
+        };
+
+        flash@2 {
+            compatible = "jedec,spi-nor";
+            spi-max-frequency = <50000000>;
+            reg = <2>, <3>;
+            stacked-memories = /bits/ 64 <0x10000000 0x10000000>;
+        };
+    };