Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 79 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt
new file mode 100644
index 000000000..8434a65fc
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-orion.txt
@@ -0,0 +1,79 @@
+Marvell Orion SPI device
+
+Required properties:
+- compatible : should be on of the following:
+    - "marvell,orion-spi" for the Orion, mv78x00, Kirkwood and Dove SoCs
+    - "marvell,armada-370-spi", for the Armada 370 SoCs
+    - "marvell,armada-375-spi", for the Armada 375 SoCs
+    - "marvell,armada-380-spi", for the Armada 38x SoCs
+    - "marvell,armada-390-spi", for the Armada 39x SoCs
+    - "marvell,armada-xp-spi", for the Armada XP SoCs
+- reg : offset and length of the register set for the device.
+	This property can optionally have additional entries to configure
+	the SPI direct access mode that some of the Marvell SoCs support
+	additionally to the normal indirect access (PIO) mode. The values
+	for the MBus "target" and "attribute" are defined in the Marvell
+	SoC "Functional Specifications" Manual in the chapter "Marvell
+	Core Processor Address Decoding".
+	The eight register sets following the control registers refer to
+	chip-select lines 0 through 7 respectively.
+- cell-index : Which of multiple SPI controllers is this.
+- clocks : pointers to the reference clocks for this device, the first
+	   one is the one used for the clock on the spi bus, the
+	   second one is optional and is the clock used for the
+	   functional part of the controller
+
+Optional properties:
+- interrupts : Is currently not used.
+- clock-names : names of used clocks, mandatory if the second clock is
+		used, the name must be "core", and "axi" (the latter
+		is only for Armada 7K/8K).
+
+
+Example:
+       spi@10600 {
+	       compatible = "marvell,orion-spi";
+	       #address-cells = <1>;
+	       #size-cells = <0>;
+	       cell-index = <0>;
+	       reg = <0x10600 0x28>;
+	       interrupts = <23>;
+       };
+
+Example with SPI direct mode support (optionally):
+	spi0: spi@10600 {
+		compatible = "marvell,orion-spi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cell-index = <0>;
+		reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */
+		      <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */
+		      <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
+		      <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */
+		      <MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */
+		      <MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */
+		      <MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */
+		      <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */
+		      <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */
+		interrupts = <23>;
+	};
+
+To enable the direct mode, the board specific 'ranges' property in the
+'soc' node needs to add the entries for the desired SPI controllers
+and its chip-selects that are used in the direct mode instead of PIO
+mode. Here an example for this (SPI controller 0, device 1 and SPI
+controller 1, device 2 are used in direct mode. All other SPI device
+are used in the default indirect (PIO) mode):
+	soc {
+		/*
+		 * Enable the SPI direct access by configuring an entry
+		 * here in the board-specific ranges property
+		 */
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>,	/* internal regs */
+			 <MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>,	/* BootROM       */
+			 <MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>,	/* SPI0-DEV1 */
+			 <MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>;	/* SPI1-DEV2 */
+
+For further information on the MBus bindings, please see the MBus
+DT documentation:
+Documentation/devicetree/bindings/bus/mvebu-mbus.txt