Merging upstream version 6.7.7.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

2 files changed, 0 insertions, 98 deletions

diff --git a/Documentation/networking/device_drivers/appletalk/cops.rst b/Documentation/networking/device_drivers/appletalk/cops.rst
deleted file mode 100644
index 964ba80599..0000000000
--- a/Documentation/networking/device_drivers/appletalk/cops.rst
+++ /dev/null
@@ -1,80 +0,0 @@
-.. SPDX-License-Identifier: GPL-2.0
-
-========================================
-The COPS LocalTalk Linux driver (cops.c)
-========================================
-
-By Jay Schulist <jschlst@samba.org>
-
-This driver has two modes and they are: Dayna mode and Tangent mode.
-Each mode corresponds with the type of card. It has been found
-that there are 2 main types of cards and all other cards are
-the same and just have different names or only have minor differences
-such as more IO ports. As this driver is tested it will
-become more clear exactly what cards are supported.
-
-Right now these cards are known to work with the COPS driver. The
-LT-200 cards work in a somewhat more limited capacity than the
-DL200 cards, which work very well and are in use by many people.
-
-TANGENT driver mode:
-	- Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200
-
-DAYNA driver mode:
-	- Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95,
-	- Farallon PhoneNET PC III, Farallon PhoneNET PC II
-
-Other cards possibly supported mode unknown though:
-	- Dayna DL2000 (Full length)
-
-The COPS driver defaults to using Dayna mode. To change the driver's
-mode if you built a driver with dual support use board_type=1 or
-board_type=2 for Dayna or Tangent with insmod.
-
-Operation/loading of the driver
-===============================
-
-Use modprobe like this:	/sbin/modprobe cops.o (IO #) (IRQ #)
-If you do not specify any options the driver will try and use the IO = 0x240,
-IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing.
-
-To load multiple COPS driver Localtalk cards you can do one of the following::
-
-	insmod cops io=0x240 irq=5
-	insmod -o cops2 cops io=0x260 irq=3
-
-Or in lilo.conf put something like this::
-
-	append="ether=5,0x240,lt0 ether=3,0x260,lt1"
-
-Then bring up the interface with ifconfig. It will look something like this::
-
-  lt0       Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00
-	    inet addr:192.168.1.2  Bcast:192.168.1.255  Mask:255.255.255.0
-	    UP BROADCAST RUNNING NOARP MULTICAST  MTU:600  Metric:1
-	    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
-	    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0
-
-Netatalk Configuration
-======================
-
-You will need to configure atalkd with something like the following to make
-it work with the cops.c driver.
-
-* For single LTalk card use::
-
-    dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033"
-    lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
-
-* For multiple cards, Ethernet and LocalTalk::
-
-    eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033"
-    lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
-
-* For multiple LocalTalk cards, and an Ethernet card.
-
-* Order seems to matter here, Ethernet last::
-
-    lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1"
-    lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2"
-    eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk"
diff --git a/Documentation/networking/device_drivers/appletalk/index.rst b/Documentation/networking/device_drivers/appletalk/index.rst
deleted file mode 100644
index c196baeb08..0000000000
--- a/Documentation/networking/device_drivers/appletalk/index.rst
+++ /dev/null
@@ -1,18 +0,0 @@
-.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-
-AppleTalk Device Drivers
-========================
-
-Contents:
-
-.. toctree::
-   :maxdepth: 2
-
-   cops
-
-.. only::  subproject and html
-
-   Indices
-   =======
-
-   * :ref:`genindex`