Adding upstream version 6.7.7.upstream/6.7.7

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 180 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/qcom/pm8226.dtsi b/arch/arm/boot/dts/qcom/pm8226.dtsi
new file mode 100644
index 0000000000..2413778f37
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8226.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: BSD-3-Clause
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8226-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8226_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm8226_0: pm8226@0 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8226_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		smbb: charger@1000 {
+			compatible = "qcom,pm8226-charger";
+			reg = <0x1000>;
+			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "chg-done",
+					  "chg-fast",
+					  "chg-trkl",
+					  "bat-temp-ok",
+					  "bat-present",
+					  "chg-gone",
+					  "usb-valid",
+					  "dc-valid";
+
+			chg_otg: otg-vbus { };
+		};
+
+		pm8226_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8226_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			channel@7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+			channel@8 {
+				reg = <VADC_DIE_TEMP>;
+				label = "die_temp";
+			};
+			channel@9 {
+				reg = <VADC_REF_625MV>;
+				label = "ref_625mv";
+			};
+			channel@a {
+				reg = <VADC_REF_1250MV>;
+				label = "ref_1250mv";
+			};
+			channel@e {
+				reg = <VADC_GND_REF>;
+			};
+			channel@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8226_iadc: adc@3600 {
+			compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
+			reg = <0x3600>;
+			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pm8226_mpps: mpps@a000 {
+			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8226_gpios: gpio@c000 {
+			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_gpios 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8226_1: pm8226@1 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8226_spmi_regulators: regulators {
+			compatible = "qcom,pm8226-regulators";
+		};
+
+		pm8226_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+	};
+};