diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-11 08:27:49 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-11 08:27:49 +0000 |
commit | ace9429bb58fd418f0c81d4c2835699bddf6bde6 (patch) | |
tree | b2d64bc10158fdd5497876388cd68142ca374ed3 /arch/arm64/boot/dts/qcom/apq8096-db820c.dts | |
parent | Initial commit. (diff) | |
download | linux-ace9429bb58fd418f0c81d4c2835699bddf6bde6.tar.xz linux-ace9429bb58fd418f0c81d4c2835699bddf6bde6.zip |
Adding upstream version 6.6.15.upstream/6.6.15
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'arch/arm64/boot/dts/qcom/apq8096-db820c.dts')
-rw-r--r-- | arch/arm64/boot/dts/qcom/apq8096-db820c.dts | 1137 |
1 files changed, 1137 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts new file mode 100644 index 0000000000..3067a4091a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts @@ -0,0 +1,1137 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "msm8996.dtsi" +#include "pm8994.dtsi" +#include "pmi8994.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/sound/qcom,q6afe.h> +#include <dt-bindings/sound/qcom,q6asm.h> +#include <dt-bindings/sound/qcom,wcd9335.h> + +/* + * GPIO name legend: proper name = the GPIO line is used as GPIO + * NC = not connected (pin out but not routed from the chip to + * anything the board) + * "[PER]" = pin is muxed for [peripheral] (not GPIO) + * LSEC = Low Speed External Connector + * P HSEC = Primary High Speed External Connector + * S HSEC = Secondary High Speed External Connector + * J14 = Camera Connector + * TP = Test Points + * + * Line names are taken from the schematic "DragonBoard 820c", + * drawing no: LM25-P2751-1 + * + * For the lines routed to the external connectors the + * lines are named after the 96Boards CE Specification 1.0, + * Appendix "Expansion Connector Signal Description". + * + * When the 96Board naming of a line and the schematic name of + * the same line are in conflict, the 96Board specification + * takes precedence, which means that the external UART on the + * LSEC is named UART0 while the schematic and SoC names this + * UART3. This is only for the informational lines i.e. "[FOO]", + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only + * ones actually used for GPIO. + */ + +/ { + model = "Qualcomm Technologies, Inc. DB820c"; + compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096"; + + aliases { + serial0 = &blsp2_uart2; + serial1 = &blsp2_uart3; + serial2 = &blsp1_uart2; + i2c0 = &blsp1_i2c3; + i2c1 = &blsp2_i2c1; + i2c2 = &blsp2_i2c1; + spi0 = &blsp1_spi1; + spi1 = &blsp2_spi6; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + div1_mclk: divclk1 { + compatible = "gpio-gate-clock"; + pinctrl-0 = <&audio_mclk>; + pinctrl-names = "default"; + clocks = <&rpmcc RPM_SMD_DIV_CLK1>; + #clock-cells = <0>; + enable-gpios = <&pm8994_gpios 15 0>; + }; + + divclk4: divclk4 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "divclk4"; + + pinctrl-names = "default"; + pinctrl-0 = <&divclk4_pin_a>; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_up_gpio>; + + button { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>; + }; + }; + + usb2_id: usb2-id { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb2_vbus_det_gpio>; + }; + + usb3_id: usb3-id { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb3_vbus_det_gpio>; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + wlan_en: wlan-en-1-8v { + pinctrl-names = "default"; + pinctrl-0 = <&wlan_en_gpios>; + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&pm8994_gpios 8 0>; + + /* WLAN card specific delay */ + startup-delay-us = <70000>; + enable-active-high; + }; +}; + +&blsp1_i2c3 { + /* On Low speed expansion: LS-I2C0 */ + status = "okay"; +}; + +&blsp1_spi1 { + /* On Low speed expansion */ + status = "okay"; +}; + +&blsp1_uart2 { + label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + + /* bt_disable_n gpio */ + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + + clocks = <&divclk4>; + }; +}; + +&adsp_pil { + status = "okay"; + firmware-name = "qcom/apq8096/adsp.mbn"; +}; + +&blsp2_i2c1 { + /* On High speed expansion: HS-I2C2 */ + status = "okay"; +}; + +&blsp2_i2c1 { + /* On Low speed expansion: LS-I2C1 */ + status = "okay"; +}; + +&blsp2_spi6 { + /* On High speed expansion */ + status = "okay"; +}; + +&blsp2_uart2 { + label = "LS-UART1"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_uart2_2pins_default>; + pinctrl-1 = <&blsp2_uart2_2pins_sleep>; +}; + +&blsp2_uart3 { + label = "LS-UART0"; + status = "disabled"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_uart3_4pins_default>; + pinctrl-1 = <&blsp2_uart3_4pins_sleep>; +}; + +&camss { + vdda-supply = <&vreg_l2a_1p25>; +}; + +&gpu { + status = "okay"; +}; + +&hsusb_phy1 { + status = "okay"; + + vdd-supply = <&vreg_l28a_0p925>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; +}; + +&hsusb_phy2 { + status = "okay"; + + vdd-supply = <&vreg_l28a_0p925>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; +}; + +&mdp { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_hdmi { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>; + pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>; + + core-vdda-supply = <&vreg_l12a_1p8>; + core-vcc-supply = <&vreg_s4a_1p8>; +}; + +&mdss_hdmi_phy { + status = "okay"; + + vddio-supply = <&vreg_l12a_1p8>; + vcca-supply = <&vreg_l28a_0p925>; + #phy-cells = <0>; +}; + +&mmcc { + vdd-gfx-supply = <&vdd_gfx>; +}; + +&mss_pil { + status = "okay"; + pll-supply = <&vreg_l12a_1p8>; + firmware-name = "qcom/apq8096/mba.mbn", "qcom/apq8096/modem.mbn"; +}; + +&pm8994_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&tlmm { + gpio-line-names = + "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */ + "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */ + "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */ + "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */ + "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */ + "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */ + "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */ + "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */ + "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */ + "TP93", /* GPIO_9 */ + "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */ + "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */ + "NC", /* GPIO_12 */ + "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */ + "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */ + "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */ + "TP99", /* GPIO_16 */ + "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */ + "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */ + "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */ + "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */ + "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */ + "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */ + "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */ + "GPIO-D", /* GPIO_24, LSEC pin 26 */ + "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */ + "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */ + "BLSP6_I2C_SDA", /* GPIO_27 */ + "BLSP6_I2C_SCL", /* GPIO_28 */ + "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */ + "GPIO30", /* GPIO_30, S HSEC pin 4 */ + "HDMI_CEC", /* GPIO_31 */ + "HDMI_DDC_CLOCK", /* GPIO_32 */ + "HDMI_DDC_DATA", /* GPIO_33 */ + "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */ + "PCIE0_RST_N", /* GPIO_35 */ + "PCIE0_CLKREQ_N", /* GPIO_36 */ + "PCIE0_WAKE", /* GPIO_37 */ + "SD_CARD_DET_N", /* GPIO_38 */ + "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */ + "W_DISABLE_N", /* GPIO_40 */ + "[BLSP9_UART_TX]", /* GPIO_41 */ + "[BLSP9_UART_RX]", /* GPIO_42 */ + "[BLSP2_UART_CTS_N]", /* GPIO_43 */ + "[BLSP2_UART_RFR_N]", /* GPIO_44 */ + "[BLSP3_UART_TX]", /* GPIO_45 */ + "[BLSP3_UART_RX]", /* GPIO_46 */ + "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */ + "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */ + "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */ + "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */ + "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */ + "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */ + "[CODEC_INT1_N]", /* GPIO_53 */ + "[CODEC_INT2_N]", /* GPIO_54 */ + "[BLSP7_I2C_SDA]", /* GPIO_55 */ + "[BLSP7_I2C_SCL]", /* GPIO_56 */ + "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */ + "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */ + "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */ + "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */ + "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */ + "GPIO-E", /* GPIO_62, LSEC pin 27 */ + "TP87", /* GPIO_63 */ + "[CODEC_RST_N]", /* GPIO_64 */ + "[PCM1_CLK]", /* GPIO_65 */ + "[PCM1_SYNC]", /* GPIO_66 */ + "[PCM1_DIN]", /* GPIO_67 */ + "[PCM1_DOUT]", /* GPIO_68 */ + "AUDIO_REF_CLK", /* GPIO_69 */ + "SLIMBUS_CLK", /* GPIO_70 */ + "SLIMBUS_DATA0", /* GPIO_71 */ + "SLIMBUS_DATA1", /* GPIO_72 */ + "NC", /* GPIO_73 */ + "NC", /* GPIO_74 */ + "NC", /* GPIO_75 */ + "NC", /* GPIO_76 */ + "TP94", /* GPIO_77 */ + "NC", /* GPIO_78 */ + "TP95", /* GPIO_79 */ + "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */ + "TP88", /* GPIO_81 */ + "TP89", /* GPIO_82 */ + "TP90", /* GPIO_83 */ + "TP91", /* GPIO_84 */ + "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */ + "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */ + "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */ + "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */ + "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */ + "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */ + "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */ + "NC", /* GPIO_92 */ + "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */ + "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */ + "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */ + "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */ + "NC", /* GPIO_97 */ + "CAM1_STANDBY_N", /* GPIO_98 */ + "NC", /* GPIO_99 */ + "NC", /* GPIO_100 */ + "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */ + "BOOT_CONFIG1", /* GPIO_102 */ + "USB_HUB_RESET", /* GPIO_103 */ + "CAM1_RST_N", /* GPIO_104 */ + "NC", /* GPIO_105 */ + "NC", /* GPIO_106 */ + "NC", /* GPIO_107 */ + "NC", /* GPIO_108 */ + "NC", /* GPIO_109 */ + "NC", /* GPIO_110 */ + "NC", /* GPIO_111 */ + "NC", /* GPIO_112 */ + "PMI8994_BUA", /* GPIO_113 */ + "PCIE2_RST_N", /* GPIO_114 */ + "PCIE2_CLKREQ_N", /* GPIO_115 */ + "PCIE2_WAKE", /* GPIO_116 */ + "SSC_IRQ_0", /* GPIO_117 */ + "SSC_IRQ_1", /* GPIO_118 */ + "SSC_IRQ_2", /* GPIO_119 */ + "NC", /* GPIO_120 */ + "GPIO121", /* GPIO_121, S HSEC pin 2 */ + "NC", /* GPIO_122 */ + "SSC_IRQ_6", /* GPIO_123 */ + "SSC_IRQ_7", /* GPIO_124 */ + "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */ + "BOOT_CONFIG5", /* GPIO_126 */ + "NC", /* GPIO_127 */ + "NC", /* GPIO_128 */ + "BOOT_CONFIG7", /* GPIO_129 */ + "PCIE1_RST_N", /* GPIO_130 */ + "PCIE1_CLKREQ_N", /* GPIO_131 */ + "PCIE1_WAKE", /* GPIO_132 */ + "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */ + "NC", /* GPIO_134 */ + "NC", /* GPIO_135 */ + "BOOT_CONFIG8", /* GPIO_136 */ + "NC", /* GPIO_137 */ + "NC", /* GPIO_138 */ + "GPS_SSBI2", /* GPIO_139 */ + "GPS_SSBI1", /* GPIO_140 */ + "NC", /* GPIO_141 */ + "NC", /* GPIO_142 */ + "NC", /* GPIO_143 */ + "BOOT_CONFIG6", /* GPIO_144 */ + "NC", /* GPIO_145 */ + "NC", /* GPIO_146 */ + "NC", /* GPIO_147 */ + "NC", /* GPIO_148 */ + "NC"; /* GPIO_149 */ + + sdc2_cd_on: sdc2-cd-on-state { + pins = "gpio38"; + function = "gpio"; + bias-pull-up; + drive-strength = <16>; + }; + + sdc2_cd_off: sdc2-cd-off-state { + pins = "gpio38"; + function = "gpio"; + bias-pull-up; + drive-strength = <2>; + }; + + hdmi_hpd_active: hdmi-hpd-active-state { + pins = "gpio34"; + function = "hdmi_hot"; + bias-pull-down; + drive-strength = <16>; + }; + + hdmi_hpd_suspend: hdmi-hpd-suspend-state { + pins = "gpio34"; + function = "hdmi_hot"; + bias-pull-down; + drive-strength = <2>; + }; + + hdmi_ddc_active: hdmi-ddc-active-state { + pins = "gpio32", "gpio33"; + function = "hdmi_ddc"; + drive-strength = <2>; + bias-pull-up; + }; + + hdmi_ddc_suspend: hdmi-ddc-suspend-state { + pins = "gpio32", "gpio33"; + function = "hdmi_ddc"; + drive-strength = <2>; + bias-pull-down; + }; +}; + +&pcie0 { + status = "okay"; + perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; + vddpe-3v3-supply = <&wlan_en>; + vdda-supply = <&vreg_l28a_0p925>; +}; + +&pcie1 { + status = "okay"; + perst-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>; + vdda-supply = <&vreg_l28a_0p925>; +}; + +&pcie2 { + status = "okay"; + perst-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>; + vdda-supply = <&vreg_l28a_0p925>; +}; + +&pcie_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l28a_0p925>; + vdda-pll-supply = <&vreg_l12a_1p8>; +}; + +&pm8994_gpios { + gpio-line-names = + "NC", + "KEY_VOLP_N", + "NC", + "BL1_PWM", + "GPIO-F", /* BL0_PWM, LSEC pin 28 */ + "BL1_EN", + "NC", + "WLAN_EN", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "DIVCLK1", + "DIVCLK2", + "DIVCLK3", + "DIVCLK4", + "BT_EN", + "PMIC_SLB", + "PMIC_BUA", + "USB_VBUS_DET"; + + pinctrl-names = "default"; + pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>; + + ls_exp_gpio_f: pm8994-gpio5-state { + pinconf { + pins = "gpio5"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + }; + }; + + bt_en_gpios: bt-en-pios-state { + pinconf { + pins = "gpio19"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + bias-pull-down; + }; + }; + + wlan_en_gpios: wlan-en-gpios-state { + pinconf { + pins = "gpio8"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + bias-pull-down; + }; + }; + + audio_mclk: clk-div1-state { + pinconf { + pins = "gpio15"; + function = "func1"; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + }; + }; + + volume_up_gpio: pm8996-gpio2-state { + pinconf { + pins = "gpio2"; + function = "normal"; + input-enable; + drive-push-pull; + bias-pull-up; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + }; + }; + + divclk4_pin_a: divclk4-state { + pinconf { + pins = "gpio18"; + function = PMIC_GPIO_FUNC_FUNC2; + + bias-disable; + power-source = <PM8994_GPIO_S4>; + }; + }; + + usb3_vbus_det_gpio: pm8996-gpio22-state { + pinconf { + pins = "gpio22"; + function = PMIC_GPIO_FUNC_NORMAL; + input-enable; + bias-pull-down; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + }; + }; +}; + +&pm8994_mpps { + gpio-line-names = + "VDDPX_BIAS", + "WIFI_LED", + "NC", + "BT_LED", + "PM_MPP05", + "PM_MPP06", + "PM_MPP07", + "NC"; +}; + +&pm8994_spmi_regulators { + qcom,saw-reg = <&saw3>; + vdd_s11-supply = <&vph_pwr>; + + s9 { + qcom,saw-slave; + }; + s10 { + qcom,saw-slave; + }; + s11 { + qcom,saw-leader; + regulator-name = "VDD_APCC"; + regulator-always-on; + regulator-min-microvolt = <980000>; + regulator-max-microvolt = <980000>; + }; +}; + +&pmi8994_gpios { + gpio-line-names = + "NC", + "SPKR_AMP_EN1", + "SPKR_AMP_EN2", + "TP61", + "NC", + "USB2_VBUS_DET", + "NC", + "NC", + "NC", + "NC"; + + usb2_vbus_det_gpio: pmi8996-gpio6-state { + pinconf { + pins = "gpio6"; + function = PMIC_GPIO_FUNC_NORMAL; + input-enable; + bias-pull-down; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; /* 1.8V */ + }; + }; +}; + +&pmi8994_lpg { + qcom,power-source = <1>; + + pinctrl-names = "default"; + pinctrl-0 = <&pmi8994_mpp2_userled4>; + + qcom,dtest = <0 0>, + <0 0>, + <0 0>, + <4 1>; + + status = "okay"; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + function-enumerator = <1>; + + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + function-enumerator = <0>; + }; + + led@3 { + reg = <3>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + function-enumerator = <2>; + }; + + led@4 { + reg = <4>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + function-enumerator = <3>; + }; +}; + +&pmi8994_mpps { + pmi8994_mpp2_userled4: mpp2-userled4-state { + pins = "mpp2"; + function = "sink"; + + output-low; + qcom,dtest = <4>; + }; +}; + +&pmi8994_spmi_regulators { + vdd_s2-supply = <&vph_pwr>; + + vdd_gfx: s2 { + regulator-name = "VDD_GFX"; + regulator-min-microvolt = <980000>; + regulator-max-microvolt = <980000>; + }; +}; + +&rpm_requests { + regulators-0 { + compatible = "qcom,rpm-pm8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_l1-supply = <&vreg_s1b_1p025>; + vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>; + vdd_l3_l11-supply = <&vreg_s3a_1p3>; + vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>; + vdd_l5_l7-supply = <&vreg_s5a_2p15>; + vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>; + vdd_l8_l16_l30-supply = <&vph_pwr>; + vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>; + vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>; + vdd_l14_l15-supply = <&vreg_s5a_2p15>; + vdd_l17_l29-supply = <&vph_pwr_bbyp>; + vdd_l20_l21-supply = <&vph_pwr_bbyp>; + vdd_l25-supply = <&vreg_s3a_1p3>; + vdd_lvs1_2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p3: s3 { + regulator-name = "vreg_s3a_1p3"; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + }; + + /** + * 1.8v required on LS expansion + * for mezzanine boards + */ + vreg_s4a_1p8: s4 { + regulator-name = "vreg_s4a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + vreg_s5a_2p15: s5 { + regulator-name = "vreg_s5a_2p15"; + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + }; + vreg_s7a_1p0: s7 { + regulator-name = "vreg_s7a_1p0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l1a_1p0: l1 { + regulator-name = "vreg_l1a_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + vreg_l2a_1p25: l2 { + regulator-name = "vreg_l2a_1p25"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + }; + vreg_l3a_0p875: l3 { + regulator-name = "vreg_l3a_0p875"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + }; + vreg_l4a_1p225: l4 { + regulator-name = "vreg_l4a_1p225"; + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + vreg_l6a_1p2: l6 { + regulator-name = "vreg_l6a_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + vreg_l8a_1p8: l8 { + regulator-name = "vreg_l8a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l9a_1p8: l9 { + regulator-name = "vreg_l9a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l10a_1p8: l10 { + regulator-name = "vreg_l10a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l11a_1p15: l11 { + regulator-name = "vreg_l11a_1p15"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + }; + vreg_l12a_1p8: l12 { + regulator-name = "vreg_l12a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l13a_2p95: l13 { + regulator-name = "vreg_l13a_2p95"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + vreg_l14a_1p8: l14 { + regulator-name = "vreg_l14a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l15a_1p8: l15 { + regulator-name = "vreg_l15a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l16a_2p7: l16 { + regulator-name = "vreg_l16a_2p7"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + vreg_l17a_2p8: l17 { + regulator-name = "vreg_l17a_2p8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + vreg_l18a_2p85: l18 { + regulator-name = "vreg_l18a_2p85"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2900000>; + }; + vreg_l19a_2p8: l19 { + regulator-name = "vreg_l19a_2p8"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + vreg_l20a_2p95: l20 { + regulator-name = "vreg_l20a_2p95"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + }; + vreg_l21a_2p95: l21 { + regulator-name = "vreg_l21a_2p95"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + vreg_l22a_3p0: l22 { + regulator-name = "vreg_l22a_3p0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + vreg_l23a_2p8: l23 { + regulator-name = "vreg_l23a_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + vreg_l24a_3p075: l24 { + regulator-name = "vreg_l24a_3p075"; + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + vreg_l25a_1p2: l25 { + regulator-name = "vreg_l25a_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + vreg_l26a_0p8: l27 { + regulator-name = "vreg_l26a_0p8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + vreg_l28a_0p925: l28 { + regulator-name = "vreg_l28a_0p925"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <925000>; + regulator-allow-set-load; + }; + vreg_l29a_2p8: l29 { + regulator-name = "vreg_l29a_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + vreg_l30a_1p8: l30 { + regulator-name = "vreg_l30a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l32a_1p8: l32 { + regulator-name = "vreg_l32a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs1a_1p8: lvs1 { + regulator-name = "vreg_lvs1a_1p8"; + }; + + vreg_lvs2a_1p8: lvs2 { + regulator-name = "vreg_lvs2a_1p8"; + }; + }; + + regulators-1 { + compatible = "qcom,rpm-pmi8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + vph_pwr_bbyp: boost-bypass { + regulator-name = "vph_pwr_bbyp"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_s1b_1p025: s1 { + regulator-name = "vreg_s1b_1p025"; + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + }; +}; + +&sdhc2 { + /* External SD card */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>; + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vreg_l21a_2p95>; + vqmmc-supply = <&vreg_l13a_2p95>; + status = "okay"; +}; + +&q6asmdai { + dai@0 { + reg = <0>; + }; + + dai@1 { + reg = <1>; + }; + + dai@2 { + reg = <2>; + }; +}; + +&slim_msm { + status = "okay"; + + slim@1 { + reg = <1>; + #address-cells = <2>; + #size-cells = <0>; + + tasha_ifd: tas-ifd@0,0 { + compatible = "slim217,1a0"; + reg = <0 0>; + }; + + wcd9335: codec@1,0 { + compatible = "slim217,1a0"; + reg = <1 0>; + + clock-names = "mclk", "slimbus"; + clocks = <&div1_mclk>, + <&rpmcc RPM_SMD_BB_CLK1>; + interrupt-parent = <&tlmm>; + interrupts = <54 IRQ_TYPE_LEVEL_HIGH>, + <53 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "intr1", "intr2"; + interrupt-controller; + #interrupt-cells = <1>; + + pinctrl-0 = <&cdc_reset_active &wcd_intr_default>; + pinctrl-names = "default"; + + reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>; + slim-ifc-dev = <&tasha_ifd>; + + #sound-dai-cells = <1>; + + vdd-buck-supply = <&vreg_s4a_1p8>; + vdd-buck-sido-supply = <&vreg_s4a_1p8>; + vdd-tx-supply = <&vreg_s4a_1p8>; + vdd-rx-supply = <&vreg_s4a_1p8>; + vdd-io-supply = <&vreg_s4a_1p8>; + }; + }; +}; + +&sound { + compatible = "qcom,apq8096-sndcard"; + model = "DB820c"; + audio-routing = "RX_BIAS", "MCLK", + "MM_DL1", "MultiMedia1 Playback", + "MM_DL2", "MultiMedia2 Playback", + "MultiMedia3 Capture", "MM_UL3"; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + mm2-dai-link { + link-name = "MultiMedia2"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; + }; + }; + + mm3-dai-link { + link-name = "MultiMedia3"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; + }; + }; + + hdmi-dai-link { + link-name = "HDMI"; + cpu { + sound-dai = <&q6afedai HDMI_RX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&mdss_hdmi 0>; + }; + }; + + slim-dai-link { + link-name = "SLIM Playback"; + cpu { + sound-dai = <&q6afedai SLIMBUS_6_RX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&wcd9335 AIF4_PB>; + }; + }; + + slimcap-dai-link { + link-name = "SLIM Capture"; + cpu { + sound-dai = <&q6afedai SLIMBUS_0_TX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&wcd9335 AIF1_CAP>; + }; + }; +}; + +&ufsphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l28a_0p925>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vddp-ref-clk-supply = <&vreg_l25a_1p2>; +}; + +&ufshc { + status = "okay"; + + vcc-supply = <&vreg_l20a_2p95>; + vccq-supply = <&vreg_l25a_1p2>; + vccq2-supply = <&vreg_s4a_1p8>; + + vcc-max-microamp = <600000>; + vccq-max-microamp = <450000>; + vccq2-max-microamp = <450000>; +}; + +&usb2 { + status = "okay"; + extcon = <&usb2_id>; +}; + +&usb2_dwc3 { + extcon = <&usb2_id>; + dr_mode = "otg"; + maximum-speed = "high-speed"; +}; + +&usb3 { + status = "okay"; + extcon = <&usb3_id>; +}; + +&usb3_dwc3 { + extcon = <&usb3_id>; + dr_mode = "otg"; +}; + +&usb3phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l28a_0p925>; + vdda-pll-supply = <&vreg_l12a_1p8>; +}; + +&venus { + status = "okay"; +}; |