diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-11 08:27:49 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-11 08:27:49 +0000 |
commit | ace9429bb58fd418f0c81d4c2835699bddf6bde6 (patch) | |
tree | b2d64bc10158fdd5497876388cd68142ca374ed3 /arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi | |
parent | Initial commit. (diff) | |
download | linux-ace9429bb58fd418f0c81d4c2835699bddf6bde6.tar.xz linux-ace9429bb58fd418f0c81d4c2835699bddf6bde6.zip |
Adding upstream version 6.6.15.upstream/6.6.15
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi')
-rw-r--r-- | arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi | 575 |
1 files changed, 575 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi new file mode 100644 index 0000000000..68e634f821 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi @@ -0,0 +1,575 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi + * + * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com> + * Copyright (c) 2016, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include "msm8998.dtsi" +#include "pm8005.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" + +/ { + /* Required for bootloader to select correct board */ + qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */ + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */ + framebuffer0: framebuffer@9d400000 { + compatible = "simple-framebuffer"; + reg = <0x0 0x9d400000 0x0 0x2400000>; + width = <1080>; + height = <1920>; + stride = <(1080 * 4)>; + format = "a8r8g8b8"; + /* + * That's a lot of clocks, but it's necessary due + * to unused clk cleanup & no panel driver yet.. + */ + clocks = <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_AXI_CLK>, + <&mmcc MDSS_VSYNC_CLK>, + <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_BYTE0_CLK>, + <&mmcc MDSS_BYTE0_INTF_CLK>, + <&mmcc MDSS_PCLK0_CLK>, + <&mmcc MDSS_ESC0_CLK>; + power-domains = <&mmcc MDSS_GDSC>; + }; + }; + + reserved-memory { + /* Bootloader display framebuffer region */ + cont_splash_mem: memory@9d400000 { + reg = <0x0 0x9d400000 0x0 0x2400000>; + no-map; + }; + + /* For getting crash logs using Android downstream kernels */ + ramoops@ac000000 { + compatible = "ramoops"; + reg = <0x0 0xac000000 0x0 0x200000>; + console-size = <0x80000>; + pmsg-size = <0x40000>; + record-size = <0x8000>; + ftrace-size = <0x20000>; + }; + + /* + * The following memory regions on downstream are "dynamically allocated" + * but given the same addresses every time. Hard code them as these addresses + * are where the OnePlus signed firmware expects them to be. + */ + ipa_fws_region: ipa@f6800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf6800000 0x0 0x5000>; + no-map; + }; + zap_shader_region: gpu@f6900000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf6900000 0x0 0x2000>; + no-map; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "Volume buttons"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&vol_keys_default>; + + button-vol-down { + label = "Volume down"; + gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + debounce-interval = <15>; + wakeup-source; + }; + + button-vol-up { + label = "Volume up"; + gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + wakeup-source; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + label = "Hall effect sensor"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_sensor_default>; + + event-hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + wakeup-source; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; +}; + +/* + * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem + * region by 4 MiB to account for this while relocating the other now + * conflicting memory nodes accordingly. + */ +&adsp_mem { + reg = <0x0 0x8b200000 0x0 0x1e00000>; +}; +&mpss_mem { + reg = <0x0 0x8d000000 0x0 0x7000000>; +}; +&venus_mem { + reg = <0x0 0x94000000 0x0 0x500000>; +}; +&mba_mem { + reg = <0x0 0x94500000 0x0 0x200000>; +}; +&slpi_mem { + reg = <0x0 0x94700000 0x0 0xf00000>; +}; +&ipa_fw_mem { + reg = <0x0 0x95600000 0x0 0x10000>; +}; +&ipa_gsi_mem { + reg = <0x0 0x95610000 0x0 0x5000>; +}; +&gpu_mem { + reg = <0x0 0x95615000 0x0 0x100000>; +}; +&wlan_msa_mem { + reg = <0x0 0x95715000 0x0 0x100000>; +}; + +&blsp1_i2c5 { + status = "okay"; + + touchscreen@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_reset_active>; + + vdd-supply = <&vreg_l28_3p0>; + vio-supply = <&vreg_l6a_1p8>; + + syna,reset-delay-ms = <20>; + syna,startup-delay-ms = <20>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + syna,rezero-wait-ms = <20>; + syna,sensor-type = <1>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <122>; + }; + }; +}; + +&blsp1_i2c6 { + status = "okay"; + + nfc@28 { + compatible = "nxp,nxp-nci-i2c"; + reg = <0x28>; + + interrupt-parent = <&tlmm>; + interrupts = <92 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&nfc_int_active &nfc_enable_active>; + }; +}; + +&blsp1_uart3 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&blsp1_uart3_on { + rx-pins { + /delete-property/ bias-disable; + /* + * Configure a pull-up on 46 (RX). This is needed to + * avoid garbage data when the TX pin of the Bluetooth + * module is in tri-state (module powered off or not + * driving the signal yet). + */ + bias-pull-up; + }; + + cts-pins { + /delete-property/ bias-disable; + /* + * Configure a pull-down on 47 (CTS) to match the pull + * of the Bluetooth module. + */ + bias-pull-down; + }; +}; + +&blsp2_uart1 { + status = "okay"; +}; + +&pm8005_regulators { + /* VDD_GFX supply */ + pm8005_s1: s1 { + regulator-min-microvolt = <524000>; + regulator-max-microvolt = <1100000>; + regulator-enable-ramp-delay = <500>; + /* Hack until we rig up the gpu consumer */ + regulator-always-on; + }; +}; + +&pm8998_gpios { + vol_keys_default: vol-keys-state { + pins = "gpio5", "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + }; +}; + +&qusb2phy { + status = "okay"; + + vdd-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; +}; + +&rpm_requests { + regulators-0 { + compatible = "qcom,rpm-pm8998-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_s13-supply = <&vph_pwr>; + vdd_l1_l27-supply = <&vreg_s7a_1p025>; + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; + vdd_l3_l11-supply = <&vreg_s7a_1p025>; + vdd_l4_l5-supply = <&vreg_s7a_1p025>; + vdd_l6-supply = <&vreg_s5a_2p04>; + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; + vdd_l9-supply = <&vreg_bob>; + vdd_l10_l23_l25-supply = <&vreg_bob>; + vdd_l13_l19_l21-supply = <&vreg_bob>; + vdd_l16_l28-supply = <&vreg_bob>; + vdd_l18_l22-supply = <&vreg_bob>; + vdd_l20_l24-supply = <&vreg_bob>; + vdd_l26-supply = <&vreg_s3a_1p35>; + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: s3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + + vreg_s5a_2p04: s5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: s7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vreg_l1a_0p875: l1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + }; + + vreg_l2a_1p2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l3a_1p0: l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l5a_0p8: l5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <1808000>; + }; + + vreg_l7a_1p8: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l8a_1p2: l8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l11a_1p0: l11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l14a_1p88: l14 { + regulator-min-microvolt = <1880000>; + regulator-max-microvolt = <1880000>; + }; + + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + + vreg_l17a_1p3: l17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l18a_2p7: l18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + + vreg_l19a_3p0: l19 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + }; + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-system-load = <800000>; + regulator-allow-set-load; + }; + + vreg_l22a_2p85: l22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <2864000>; + }; + + vreg_l23a_3p3: l23 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; + }; + + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + }; + + vreg_l25a_3p3: l25 { + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3312000>; + }; + + vreg_l26a_1p2: l26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + + vreg_l28_3p0: l28 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + + vreg_lvs1a_1p8: lvs1 { }; + vreg_lvs2a_1p8: lvs2 { }; + }; + + regulators-1 { + compatible = "qcom,rpm-pmi8998-regulators"; + + vdd_bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + hall_sensor_default: hall-sensor-default-state { + pins = "gpio124"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + ts_int_active: ts-int-active-state { + pins = "gpio125"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_reset_active: ts-reset-active-state { + pins = "gpio89"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + nfc_int_active: nfc-int-active-state { + pins = "gpio92"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + nfc_enable_active: nfc-enable-active-state { + pins = "gpio12", "gpio116"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; +}; + +&ufshc { + status = "okay"; + + vcc-supply = <&vreg_l20a_2p95>; + vccq-supply = <&vreg_l26a_1p2>; + vccq2-supply = <&vreg_s4a_1p8>; + vcc-max-microamp = <750000>; + vccq-max-microamp = <560000>; + vccq2-max-microamp = <750000>; +}; + +&ufsphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; + vddp-ref-clk-supply = <&vreg_l26a_1p2>; +}; + +&usb3 { + status = "okay"; + + /* Disable USB3 clock requirement as the device only supports USB2 */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb3_dwc3 { + /* Drop the unused USB 3 PHY */ + phys = <&qusb2phy>; + phy-names = "usb2-phy"; + + /* Fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + /* Force to peripheral until we can switch modes */ + dr_mode = "peripheral"; +}; + +&wifi { + /* Leave disabled until MSS is functional */ + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; +}; |