Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

6 files changed, 1598 insertions, 0 deletions

diff --git a/drivers/clk/keystone/Kconfig b/drivers/clk/keystone/Kconfig
new file mode 100644
index 0000000000..e64d672604
--- /dev/null
+++ b/drivers/clk/keystone/Kconfig
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config COMMON_CLK_KEYSTONE
+	tristate "Clock drivers for Keystone based SOCs"
+	depends on (ARCH_KEYSTONE || COMPILE_TEST) && OF
+	help
+	  Supports clock drivers for Keystone based SOCs. These SOCs have local
+	  a power sleep control module that gate the clock to the IPs and PLLs.
+
+config TI_SCI_CLK
+	tristate "TI System Control Interface clock drivers"
+	depends on (ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST) && OF
+	depends on TI_SCI_PROTOCOL
+	default ARCH_KEYSTONE
+	help
+	  This adds the clock driver support over TI System Control Interface.
+	  If you wish to use clock resources from the PMMC firmware, say Y.
+	  Otherwise, say N.
+
+config TI_SCI_CLK_PROBE_FROM_FW
+	bool "Probe available clocks from firmware"
+	depends on TI_SCI_CLK
+	default n
+	help
+	  Forces the TI SCI clock driver to probe available clocks from the
+	  firmware. By default, only the used clocks are probed from DT.
+	  This is mostly only useful for debugging purposes, and will
+	  increase the boot time of the device. If you want the clocks probed
+	  from firmware, say Y. Otherwise, say N.
+
+config TI_SYSCON_CLK
+	tristate "Syscon based clock driver for K2/K3 SoCs"
+	depends on ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
+	default ARCH_KEYSTONE || ARCH_K3
+	help
+	  This adds clock driver support for syscon based gate
+	  clocks on TI's K2 and K3 SoCs.
diff --git a/drivers/clk/keystone/Makefile b/drivers/clk/keystone/Makefile
new file mode 100644
index 0000000000..0e426e648f
--- /dev/null
+++ b/drivers/clk/keystone/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_COMMON_CLK_KEYSTONE)	+= pll.o gate.o
+obj-$(CONFIG_TI_SCI_CLK)		+= sci-clk.o
+obj-$(CONFIG_TI_SYSCON_CLK)		+= syscon-clk.o
diff --git a/drivers/clk/keystone/gate.c b/drivers/clk/keystone/gate.c
new file mode 100644
index 0000000000..13ea047489
--- /dev/null
+++ b/drivers/clk/keystone/gate.c
@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Clock driver for Keystone 2 based devices
+ *
+ * Copyright (C) 2013 Texas Instruments.
+ *	Murali Karicheri <m-karicheri2@ti.com>
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ */
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/of_address.h>
+#include <linux/of.h>
+#include <linux/module.h>
+
+/* PSC register offsets */
+#define PTCMD			0x120
+#define PTSTAT			0x128
+#define PDSTAT			0x200
+#define PDCTL			0x300
+#define MDSTAT			0x800
+#define MDCTL			0xa00
+
+/* PSC module states */
+#define PSC_STATE_SWRSTDISABLE	0
+#define PSC_STATE_SYNCRST	1
+#define PSC_STATE_DISABLE	2
+#define PSC_STATE_ENABLE	3
+
+#define MDSTAT_STATE_MASK	0x3f
+#define MDSTAT_MCKOUT		BIT(12)
+#define PDSTAT_STATE_MASK	0x1f
+#define MDCTL_FORCE		BIT(31)
+#define MDCTL_LRESET		BIT(8)
+#define PDCTL_NEXT		BIT(0)
+
+/* Maximum timeout to bail out state transition for module */
+#define STATE_TRANS_MAX_COUNT	0xffff
+
+static void __iomem *domain_transition_base;
+
+/**
+ * struct clk_psc_data - PSC data
+ * @control_base: Base address for a PSC control
+ * @domain_base: Base address for a PSC domain
+ * @domain_id: PSC domain id number
+ */
+struct clk_psc_data {
+	void __iomem *control_base;
+	void __iomem *domain_base;
+	u32 domain_id;
+};
+
+/**
+ * struct clk_psc - PSC clock structure
+ * @hw: clk_hw for the psc
+ * @psc_data: PSC driver specific data
+ * @lock: Spinlock used by the driver
+ */
+struct clk_psc {
+	struct clk_hw hw;
+	struct clk_psc_data *psc_data;
+	spinlock_t *lock;
+};
+
+static DEFINE_SPINLOCK(psc_lock);
+
+#define to_clk_psc(_hw) container_of(_hw, struct clk_psc, hw)
+
+static void psc_config(void __iomem *control_base, void __iomem *domain_base,
+						u32 next_state, u32 domain_id)
+{
+	u32 ptcmd, pdstat, pdctl, mdstat, mdctl, ptstat;
+	u32 count = STATE_TRANS_MAX_COUNT;
+
+	mdctl = readl(control_base + MDCTL);
+	mdctl &= ~MDSTAT_STATE_MASK;
+	mdctl |= next_state;
+	/* For disable, we always put the module in local reset */
+	if (next_state == PSC_STATE_DISABLE)
+		mdctl &= ~MDCTL_LRESET;
+	writel(mdctl, control_base + MDCTL);
+
+	pdstat = readl(domain_base + PDSTAT);
+	if (!(pdstat & PDSTAT_STATE_MASK)) {
+		pdctl = readl(domain_base + PDCTL);
+		pdctl |= PDCTL_NEXT;
+		writel(pdctl, domain_base + PDCTL);
+	}
+
+	ptcmd = 1 << domain_id;
+	writel(ptcmd, domain_transition_base + PTCMD);
+	do {
+		ptstat = readl(domain_transition_base + PTSTAT);
+	} while (((ptstat >> domain_id) & 1) && count--);
+
+	count = STATE_TRANS_MAX_COUNT;
+	do {
+		mdstat = readl(control_base + MDSTAT);
+	} while (!((mdstat & MDSTAT_STATE_MASK) == next_state) && count--);
+}
+
+static int keystone_clk_is_enabled(struct clk_hw *hw)
+{
+	struct clk_psc *psc = to_clk_psc(hw);
+	struct clk_psc_data *data = psc->psc_data;
+	u32 mdstat = readl(data->control_base + MDSTAT);
+
+	return (mdstat & MDSTAT_MCKOUT) ? 1 : 0;
+}
+
+static int keystone_clk_enable(struct clk_hw *hw)
+{
+	struct clk_psc *psc = to_clk_psc(hw);
+	struct clk_psc_data *data = psc->psc_data;
+	unsigned long flags = 0;
+
+	if (psc->lock)
+		spin_lock_irqsave(psc->lock, flags);
+
+	psc_config(data->control_base, data->domain_base,
+				PSC_STATE_ENABLE, data->domain_id);
+
+	if (psc->lock)
+		spin_unlock_irqrestore(psc->lock, flags);
+
+	return 0;
+}
+
+static void keystone_clk_disable(struct clk_hw *hw)
+{
+	struct clk_psc *psc = to_clk_psc(hw);
+	struct clk_psc_data *data = psc->psc_data;
+	unsigned long flags = 0;
+
+	if (psc->lock)
+		spin_lock_irqsave(psc->lock, flags);
+
+	psc_config(data->control_base, data->domain_base,
+				PSC_STATE_DISABLE, data->domain_id);
+
+	if (psc->lock)
+		spin_unlock_irqrestore(psc->lock, flags);
+}
+
+static const struct clk_ops clk_psc_ops = {
+	.enable = keystone_clk_enable,
+	.disable = keystone_clk_disable,
+	.is_enabled = keystone_clk_is_enabled,
+};
+
+/**
+ * clk_register_psc - register psc clock
+ * @dev: device that is registering this clock
+ * @name: name of this clock
+ * @parent_name: name of clock's parent
+ * @psc_data: platform data to configure this clock
+ * @lock: spinlock used by this clock
+ */
+static struct clk *clk_register_psc(struct device *dev,
+			const char *name,
+			const char *parent_name,
+			struct clk_psc_data *psc_data,
+			spinlock_t *lock)
+{
+	struct clk_init_data init;
+	struct clk_psc *psc;
+	struct clk *clk;
+
+	psc = kzalloc(sizeof(*psc), GFP_KERNEL);
+	if (!psc)
+		return ERR_PTR(-ENOMEM);
+
+	init.name = name;
+	init.ops = &clk_psc_ops;
+	init.flags = 0;
+	init.parent_names = (parent_name ? &parent_name : NULL);
+	init.num_parents = (parent_name ? 1 : 0);
+
+	psc->psc_data = psc_data;
+	psc->lock = lock;
+	psc->hw.init = &init;
+
+	clk = clk_register(NULL, &psc->hw);
+	if (IS_ERR(clk))
+		kfree(psc);
+
+	return clk;
+}
+
+/**
+ * of_psc_clk_init - initialize psc clock through DT
+ * @node: device tree node for this clock
+ * @lock: spinlock used by this clock
+ */
+static void __init of_psc_clk_init(struct device_node *node, spinlock_t *lock)
+{
+	const char *clk_name = node->name;
+	const char *parent_name;
+	struct clk_psc_data *data;
+	struct clk *clk;
+	int i;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data) {
+		pr_err("%s: Out of memory\n", __func__);
+		return;
+	}
+
+	i = of_property_match_string(node, "reg-names", "control");
+	data->control_base = of_iomap(node, i);
+	if (!data->control_base) {
+		pr_err("%s: control ioremap failed\n", __func__);
+		goto out;
+	}
+
+	i = of_property_match_string(node, "reg-names", "domain");
+	data->domain_base = of_iomap(node, i);
+	if (!data->domain_base) {
+		pr_err("%s: domain ioremap failed\n", __func__);
+		goto unmap_ctrl;
+	}
+
+	of_property_read_u32(node, "domain-id", &data->domain_id);
+
+	/* Domain transition registers at fixed address space of domain_id 0 */
+	if (!domain_transition_base && !data->domain_id)
+		domain_transition_base = data->domain_base;
+
+	of_property_read_string(node, "clock-output-names", &clk_name);
+	parent_name = of_clk_get_parent_name(node, 0);
+	if (!parent_name) {
+		pr_err("%s: Parent clock not found\n", __func__);
+		goto unmap_domain;
+	}
+
+	clk = clk_register_psc(NULL, clk_name, parent_name, data, lock);
+	if (!IS_ERR(clk)) {
+		of_clk_add_provider(node, of_clk_src_simple_get, clk);
+		return;
+	}
+
+	pr_err("%s: error registering clk %pOFn\n", __func__, node);
+
+unmap_domain:
+	iounmap(data->domain_base);
+unmap_ctrl:
+	iounmap(data->control_base);
+out:
+	kfree(data);
+	return;
+}
+
+/**
+ * of_keystone_psc_clk_init - initialize psc clock through DT
+ * @node: device tree node for this clock
+ */
+static void __init of_keystone_psc_clk_init(struct device_node *node)
+{
+	of_psc_clk_init(node, &psc_lock);
+}
+CLK_OF_DECLARE(keystone_gate_clk, "ti,keystone,psc-clock",
+					of_keystone_psc_clk_init);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Clock driver for Keystone 2 based devices");
+MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>");
+MODULE_AUTHOR("Santosh Shilimkar <santosh.shilimkar@ti.com>");
diff --git a/drivers/clk/keystone/pll.c b/drivers/clk/keystone/pll.c
new file mode 100644
index 0000000000..6bbdd4705d
--- /dev/null
+++ b/drivers/clk/keystone/pll.c
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * PLL clock driver for Keystone devices
+ *
+ * Copyright (C) 2013 Texas Instruments Inc.
+ *	Murali Karicheri <m-karicheri2@ti.com>
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ */
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/of_address.h>
+#include <linux/of.h>
+#include <linux/module.h>
+
+#define PLLM_LOW_MASK		0x3f
+#define PLLM_HIGH_MASK		0x7ffc0
+#define MAIN_PLLM_HIGH_MASK	0x7f000
+#define PLLM_HIGH_SHIFT		6
+#define PLLD_MASK		0x3f
+#define CLKOD_MASK		0x780000
+#define CLKOD_SHIFT		19
+
+/**
+ * struct clk_pll_data - pll data structure
+ * @has_pllctrl: If set to non zero, lower 6 bits of multiplier is in pllm
+ *	register of pll controller, else it is in the pll_ctrl0((bit 11-6)
+ * @phy_pllm: Physical address of PLLM in pll controller. Used when
+ *	has_pllctrl is non zero.
+ * @phy_pll_ctl0: Physical address of PLL ctrl0. This could be that of
+ *	Main PLL or any other PLLs in the device such as ARM PLL, DDR PLL
+ *	or PA PLL available on keystone2. These PLLs are controlled by
+ *	this register. Main PLL is controlled by a PLL controller.
+ * @pllm: PLL register map address for multiplier bits
+ * @pllod: PLL register map address for post divider bits
+ * @pll_ctl0: PLL controller map address
+ * @pllm_lower_mask: multiplier lower mask
+ * @pllm_upper_mask: multiplier upper mask
+ * @pllm_upper_shift: multiplier upper shift
+ * @plld_mask: divider mask
+ * @clkod_mask: output divider mask
+ * @clkod_shift: output divider shift
+ * @plld_mask: divider mask
+ * @postdiv: Fixed post divider
+ */
+struct clk_pll_data {
+	bool has_pllctrl;
+	u32 phy_pllm;
+	u32 phy_pll_ctl0;
+	void __iomem *pllm;
+	void __iomem *pllod;
+	void __iomem *pll_ctl0;
+	u32 pllm_lower_mask;
+	u32 pllm_upper_mask;
+	u32 pllm_upper_shift;
+	u32 plld_mask;
+	u32 clkod_mask;
+	u32 clkod_shift;
+	u32 postdiv;
+};
+
+/**
+ * struct clk_pll - Main pll clock
+ * @hw: clk_hw for the pll
+ * @pll_data: PLL driver specific data
+ */
+struct clk_pll {
+	struct clk_hw hw;
+	struct clk_pll_data *pll_data;
+};
+
+#define to_clk_pll(_hw) container_of(_hw, struct clk_pll, hw)
+
+static unsigned long clk_pllclk_recalc(struct clk_hw *hw,
+					unsigned long parent_rate)
+{
+	struct clk_pll *pll = to_clk_pll(hw);
+	struct clk_pll_data *pll_data = pll->pll_data;
+	unsigned long rate = parent_rate;
+	u32  mult = 0, prediv, postdiv, val;
+
+	/*
+	 * get bits 0-5 of multiplier from pllctrl PLLM register
+	 * if has_pllctrl is non zero
+	 */
+	if (pll_data->has_pllctrl) {
+		val = readl(pll_data->pllm);
+		mult = (val & pll_data->pllm_lower_mask);
+	}
+
+	/* bit6-12 of PLLM is in Main PLL control register */
+	val = readl(pll_data->pll_ctl0);
+	mult |= ((val & pll_data->pllm_upper_mask)
+			>> pll_data->pllm_upper_shift);
+	prediv = (val & pll_data->plld_mask);
+
+	if (!pll_data->has_pllctrl)
+		/* read post divider from od bits*/
+		postdiv = ((val & pll_data->clkod_mask) >>
+				 pll_data->clkod_shift) + 1;
+	else if (pll_data->pllod) {
+		postdiv = readl(pll_data->pllod);
+		postdiv = ((postdiv & pll_data->clkod_mask) >>
+				pll_data->clkod_shift) + 1;
+	} else
+		postdiv = pll_data->postdiv;
+
+	rate /= (prediv + 1);
+	rate = (rate * (mult + 1));
+	rate /= postdiv;
+
+	return rate;
+}
+
+static const struct clk_ops clk_pll_ops = {
+	.recalc_rate = clk_pllclk_recalc,
+};
+
+static struct clk *clk_register_pll(struct device *dev,
+			const char *name,
+			const char *parent_name,
+			struct clk_pll_data *pll_data)
+{
+	struct clk_init_data init;
+	struct clk_pll *pll;
+	struct clk *clk;
+
+	pll = kzalloc(sizeof(*pll), GFP_KERNEL);
+	if (!pll)
+		return ERR_PTR(-ENOMEM);
+
+	init.name = name;
+	init.ops = &clk_pll_ops;
+	init.flags = 0;
+	init.parent_names = (parent_name ? &parent_name : NULL);
+	init.num_parents = (parent_name ? 1 : 0);
+
+	pll->pll_data	= pll_data;
+	pll->hw.init = &init;
+
+	clk = clk_register(NULL, &pll->hw);
+	if (IS_ERR(clk))
+		goto out;
+
+	return clk;
+out:
+	kfree(pll);
+	return NULL;
+}
+
+/**
+ * _of_pll_clk_init - PLL initialisation via DT
+ * @node: device tree node for this clock
+ * @pllctrl: If true, lower 6 bits of multiplier is in pllm register of
+ *		pll controller, else it is in the control register0(bit 11-6)
+ */
+static void __init _of_pll_clk_init(struct device_node *node, bool pllctrl)
+{
+	struct clk_pll_data *pll_data;
+	const char *parent_name;
+	struct clk *clk;
+	int i;
+
+	pll_data = kzalloc(sizeof(*pll_data), GFP_KERNEL);
+	if (!pll_data) {
+		pr_err("%s: Out of memory\n", __func__);
+		return;
+	}
+
+	parent_name = of_clk_get_parent_name(node, 0);
+	if (of_property_read_u32(node, "fixed-postdiv",	&pll_data->postdiv)) {
+		/* assume the PLL has output divider register bits */
+		pll_data->clkod_mask = CLKOD_MASK;
+		pll_data->clkod_shift = CLKOD_SHIFT;
+
+		/*
+		 * Check if there is an post-divider register. If not
+		 * assume od bits are part of control register.
+		 */
+		i = of_property_match_string(node, "reg-names",
+					     "post-divider");
+		pll_data->pllod = of_iomap(node, i);
+	}
+
+	i = of_property_match_string(node, "reg-names", "control");
+	pll_data->pll_ctl0 = of_iomap(node, i);
+	if (!pll_data->pll_ctl0) {
+		pr_err("%s: ioremap failed\n", __func__);
+		iounmap(pll_data->pllod);
+		goto out;
+	}
+
+	pll_data->pllm_lower_mask = PLLM_LOW_MASK;
+	pll_data->pllm_upper_shift = PLLM_HIGH_SHIFT;
+	pll_data->plld_mask = PLLD_MASK;
+	pll_data->has_pllctrl = pllctrl;
+	if (!pll_data->has_pllctrl) {
+		pll_data->pllm_upper_mask = PLLM_HIGH_MASK;
+	} else {
+		pll_data->pllm_upper_mask = MAIN_PLLM_HIGH_MASK;
+		i = of_property_match_string(node, "reg-names", "multiplier");
+		pll_data->pllm = of_iomap(node, i);
+		if (!pll_data->pllm) {
+			iounmap(pll_data->pll_ctl0);
+			iounmap(pll_data->pllod);
+			goto out;
+		}
+	}
+
+	clk = clk_register_pll(NULL, node->name, parent_name, pll_data);
+	if (!IS_ERR_OR_NULL(clk)) {
+		of_clk_add_provider(node, of_clk_src_simple_get, clk);
+		return;
+	}
+
+out:
+	pr_err("%s: error initializing pll %pOFn\n", __func__, node);
+	kfree(pll_data);
+}
+
+/**
+ * of_keystone_pll_clk_init - PLL initialisation DT wrapper
+ * @node: device tree node for this clock
+ */
+static void __init of_keystone_pll_clk_init(struct device_node *node)
+{
+	_of_pll_clk_init(node, false);
+}
+CLK_OF_DECLARE(keystone_pll_clock, "ti,keystone,pll-clock",
+					of_keystone_pll_clk_init);
+
+/**
+ * of_keystone_main_pll_clk_init - Main PLL initialisation DT wrapper
+ * @node: device tree node for this clock
+ */
+static void __init of_keystone_main_pll_clk_init(struct device_node *node)
+{
+	_of_pll_clk_init(node, true);
+}
+CLK_OF_DECLARE(keystone_main_pll_clock, "ti,keystone,main-pll-clock",
+						of_keystone_main_pll_clk_init);
+
+/**
+ * of_pll_div_clk_init - PLL divider setup function
+ * @node: device tree node for this clock
+ */
+static void __init of_pll_div_clk_init(struct device_node *node)
+{
+	const char *parent_name;
+	void __iomem *reg;
+	u32 shift, mask;
+	struct clk *clk;
+	const char *clk_name = node->name;
+
+	of_property_read_string(node, "clock-output-names", &clk_name);
+	reg = of_iomap(node, 0);
+	if (!reg) {
+		pr_err("%s: ioremap failed\n", __func__);
+		return;
+	}
+
+	parent_name = of_clk_get_parent_name(node, 0);
+	if (!parent_name) {
+		pr_err("%s: missing parent clock\n", __func__);
+		iounmap(reg);
+		return;
+	}
+
+	if (of_property_read_u32(node, "bit-shift", &shift)) {
+		pr_err("%s: missing 'shift' property\n", __func__);
+		iounmap(reg);
+		return;
+	}
+
+	if (of_property_read_u32(node, "bit-mask", &mask)) {
+		pr_err("%s: missing 'bit-mask' property\n", __func__);
+		iounmap(reg);
+		return;
+	}
+
+	clk = clk_register_divider(NULL, clk_name, parent_name, 0, reg, shift,
+				 mask, 0, NULL);
+	if (IS_ERR(clk)) {
+		pr_err("%s: error registering divider %s\n", __func__, clk_name);
+		iounmap(reg);
+		return;
+	}
+
+	of_clk_add_provider(node, of_clk_src_simple_get, clk);
+}
+CLK_OF_DECLARE(pll_divider_clock, "ti,keystone,pll-divider-clock", of_pll_div_clk_init);
+
+/**
+ * of_pll_mux_clk_init - PLL mux setup function
+ * @node: device tree node for this clock
+ */
+static void __init of_pll_mux_clk_init(struct device_node *node)
+{
+	void __iomem *reg;
+	u32 shift, mask;
+	struct clk *clk;
+	const char *parents[2];
+	const char *clk_name = node->name;
+
+	of_property_read_string(node, "clock-output-names", &clk_name);
+	reg = of_iomap(node, 0);
+	if (!reg) {
+		pr_err("%s: ioremap failed\n", __func__);
+		return;
+	}
+
+	of_clk_parent_fill(node, parents, 2);
+	if (!parents[0] || !parents[1]) {
+		pr_err("%s: missing parent clocks\n", __func__);
+		return;
+	}
+
+	if (of_property_read_u32(node, "bit-shift", &shift)) {
+		pr_err("%s: missing 'shift' property\n", __func__);
+		return;
+	}
+
+	if (of_property_read_u32(node, "bit-mask", &mask)) {
+		pr_err("%s: missing 'bit-mask' property\n", __func__);
+		return;
+	}
+
+	clk = clk_register_mux(NULL, clk_name, (const char **)&parents,
+				ARRAY_SIZE(parents) , 0, reg, shift, mask,
+				0, NULL);
+	if (IS_ERR(clk)) {
+		pr_err("%s: error registering mux %s\n", __func__, clk_name);
+		return;
+	}
+
+	of_clk_add_provider(node, of_clk_src_simple_get, clk);
+}
+CLK_OF_DECLARE(pll_mux_clock, "ti,keystone,pll-mux-clock", of_pll_mux_clk_init);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("PLL clock driver for Keystone devices");
+MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>");
+MODULE_AUTHOR("Santosh Shilimkar <santosh.shilimkar@ti.com>");
diff --git a/drivers/clk/keystone/sci-clk.c b/drivers/clk/keystone/sci-clk.c
new file mode 100644
index 0000000000..35fe197dd3
--- /dev/null
+++ b/drivers/clk/keystone/sci-clk.c
@@ -0,0 +1,711 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * SCI Clock driver for keystone based devices
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - https://www.ti.com/
+ *	Tero Kristo <t-kristo@ti.com>
+ */
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/soc/ti/ti_sci_protocol.h>
+#include <linux/bsearch.h>
+#include <linux/list_sort.h>
+
+#define SCI_CLK_SSC_ENABLE		BIT(0)
+#define SCI_CLK_ALLOW_FREQ_CHANGE	BIT(1)
+#define SCI_CLK_INPUT_TERMINATION	BIT(2)
+
+/**
+ * struct sci_clk_provider - TI SCI clock provider representation
+ * @sci: Handle to the System Control Interface protocol handler
+ * @ops: Pointer to the SCI ops to be used by the clocks
+ * @dev: Device pointer for the clock provider
+ * @clocks: Clocks array for this device
+ * @num_clocks: Total number of clocks for this provider
+ */
+struct sci_clk_provider {
+	const struct ti_sci_handle *sci;
+	const struct ti_sci_clk_ops *ops;
+	struct device *dev;
+	struct sci_clk **clocks;
+	int num_clocks;
+};
+
+/**
+ * struct sci_clk - TI SCI clock representation
+ * @hw:		 Hardware clock cookie for common clock framework
+ * @dev_id:	 Device index
+ * @clk_id:	 Clock index
+ * @num_parents: Number of parents for this clock
+ * @provider:	 Master clock provider
+ * @flags:	 Flags for the clock
+ * @node:	 Link for handling clocks probed via DT
+ * @cached_req:	 Cached requested freq for determine rate calls
+ * @cached_res:	 Cached result freq for determine rate calls
+ */
+struct sci_clk {
+	struct clk_hw hw;
+	u16 dev_id;
+	u32 clk_id;
+	u32 num_parents;
+	struct sci_clk_provider *provider;
+	u8 flags;
+	struct list_head node;
+	unsigned long cached_req;
+	unsigned long cached_res;
+};
+
+#define to_sci_clk(_hw) container_of(_hw, struct sci_clk, hw)
+
+/**
+ * sci_clk_prepare - Prepare (enable) a TI SCI clock
+ * @hw: clock to prepare
+ *
+ * Prepares a clock to be actively used. Returns the SCI protocol status.
+ */
+static int sci_clk_prepare(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	bool enable_ssc = clk->flags & SCI_CLK_SSC_ENABLE;
+	bool allow_freq_change = clk->flags & SCI_CLK_ALLOW_FREQ_CHANGE;
+	bool input_termination = clk->flags & SCI_CLK_INPUT_TERMINATION;
+
+	return clk->provider->ops->get_clock(clk->provider->sci, clk->dev_id,
+					     clk->clk_id, enable_ssc,
+					     allow_freq_change,
+					     input_termination);
+}
+
+/**
+ * sci_clk_unprepare - Un-prepares (disables) a TI SCI clock
+ * @hw: clock to unprepare
+ *
+ * Un-prepares a clock from active state.
+ */
+static void sci_clk_unprepare(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	int ret;
+
+	ret = clk->provider->ops->put_clock(clk->provider->sci, clk->dev_id,
+					    clk->clk_id);
+	if (ret)
+		dev_err(clk->provider->dev,
+			"unprepare failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+}
+
+/**
+ * sci_clk_is_prepared - Check if a TI SCI clock is prepared or not
+ * @hw: clock to check status for
+ *
+ * Checks if a clock is prepared (enabled) in hardware. Returns non-zero
+ * value if clock is enabled, zero otherwise.
+ */
+static int sci_clk_is_prepared(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	bool req_state, current_state;
+	int ret;
+
+	ret = clk->provider->ops->is_on(clk->provider->sci, clk->dev_id,
+					clk->clk_id, &req_state,
+					&current_state);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"is_prepared failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return 0;
+	}
+
+	return req_state;
+}
+
+/**
+ * sci_clk_recalc_rate - Get clock rate for a TI SCI clock
+ * @hw: clock to get rate for
+ * @parent_rate: parent rate provided by common clock framework, not used
+ *
+ * Gets the current clock rate of a TI SCI clock. Returns the current
+ * clock rate, or zero in failure.
+ */
+static unsigned long sci_clk_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	u64 freq;
+	int ret;
+
+	ret = clk->provider->ops->get_freq(clk->provider->sci, clk->dev_id,
+					   clk->clk_id, &freq);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"recalc-rate failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return 0;
+	}
+
+	return freq;
+}
+
+/**
+ * sci_clk_determine_rate - Determines a clock rate a clock can be set to
+ * @hw: clock to change rate for
+ * @req: requested rate configuration for the clock
+ *
+ * Determines a suitable clock rate and parent for a TI SCI clock.
+ * The parent handling is un-used, as generally the parent clock rates
+ * are not known by the kernel; instead these are internally handled
+ * by the firmware. Returns 0 on success, negative error value on failure.
+ */
+static int sci_clk_determine_rate(struct clk_hw *hw,
+				  struct clk_rate_request *req)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	int ret;
+	u64 new_rate;
+
+	if (clk->cached_req && clk->cached_req == req->rate) {
+		req->rate = clk->cached_res;
+		return 0;
+	}
+
+	ret = clk->provider->ops->get_best_match_freq(clk->provider->sci,
+						      clk->dev_id,
+						      clk->clk_id,
+						      req->min_rate,
+						      req->rate,
+						      req->max_rate,
+						      &new_rate);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"determine-rate failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return ret;
+	}
+
+	clk->cached_req = req->rate;
+	clk->cached_res = new_rate;
+
+	req->rate = new_rate;
+
+	return 0;
+}
+
+/**
+ * sci_clk_set_rate - Set rate for a TI SCI clock
+ * @hw: clock to change rate for
+ * @rate: target rate for the clock
+ * @parent_rate: rate of the clock parent, not used for TI SCI clocks
+ *
+ * Sets a clock frequency for a TI SCI clock. Returns the TI SCI
+ * protocol status.
+ */
+static int sci_clk_set_rate(struct clk_hw *hw, unsigned long rate,
+			    unsigned long parent_rate)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+
+	return clk->provider->ops->set_freq(clk->provider->sci, clk->dev_id,
+					    clk->clk_id, rate / 10 * 9, rate,
+					    rate / 10 * 11);
+}
+
+/**
+ * sci_clk_get_parent - Get the current parent of a TI SCI clock
+ * @hw: clock to get parent for
+ *
+ * Returns the index of the currently selected parent for a TI SCI clock.
+ */
+static u8 sci_clk_get_parent(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	u32 parent_id = 0;
+	int ret;
+
+	ret = clk->provider->ops->get_parent(clk->provider->sci, clk->dev_id,
+					     clk->clk_id, (void *)&parent_id);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"get-parent failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return 0;
+	}
+
+	parent_id = parent_id - clk->clk_id - 1;
+
+	return (u8)parent_id;
+}
+
+/**
+ * sci_clk_set_parent - Set the parent of a TI SCI clock
+ * @hw: clock to set parent for
+ * @index: new parent index for the clock
+ *
+ * Sets the parent of a TI SCI clock. Return TI SCI protocol status.
+ */
+static int sci_clk_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+
+	clk->cached_req = 0;
+
+	return clk->provider->ops->set_parent(clk->provider->sci, clk->dev_id,
+					      clk->clk_id,
+					      index + 1 + clk->clk_id);
+}
+
+static const struct clk_ops sci_clk_ops = {
+	.prepare = sci_clk_prepare,
+	.unprepare = sci_clk_unprepare,
+	.is_prepared = sci_clk_is_prepared,
+	.recalc_rate = sci_clk_recalc_rate,
+	.determine_rate = sci_clk_determine_rate,
+	.set_rate = sci_clk_set_rate,
+	.get_parent = sci_clk_get_parent,
+	.set_parent = sci_clk_set_parent,
+};
+
+/**
+ * _sci_clk_get - Gets a handle for an SCI clock
+ * @provider: Handle to SCI clock provider
+ * @sci_clk: Handle to the SCI clock to populate
+ *
+ * Gets a handle to an existing TI SCI hw clock, or builds a new clock
+ * entry and registers it with the common clock framework. Called from
+ * the common clock framework, when a corresponding of_clk_get call is
+ * executed, or recursively from itself when parsing parent clocks.
+ * Returns 0 on success, negative error code on failure.
+ */
+static int _sci_clk_build(struct sci_clk_provider *provider,
+			  struct sci_clk *sci_clk)
+{
+	struct clk_init_data init = { NULL };
+	char *name = NULL;
+	char **parent_names = NULL;
+	int i;
+	int ret = 0;
+
+	name = kasprintf(GFP_KERNEL, "clk:%d:%d", sci_clk->dev_id,
+			 sci_clk->clk_id);
+	if (!name)
+		return -ENOMEM;
+
+	init.name = name;
+
+	/*
+	 * From kernel point of view, we only care about a clocks parents,
+	 * if it has more than 1 possible parent. In this case, it is going
+	 * to have mux functionality. Otherwise it is going to act as a root
+	 * clock.
+	 */
+	if (sci_clk->num_parents < 2)
+		sci_clk->num_parents = 0;
+
+	if (sci_clk->num_parents) {
+		parent_names = kcalloc(sci_clk->num_parents, sizeof(char *),
+				       GFP_KERNEL);
+
+		if (!parent_names) {
+			ret = -ENOMEM;
+			goto err;
+		}
+
+		for (i = 0; i < sci_clk->num_parents; i++) {
+			char *parent_name;
+
+			parent_name = kasprintf(GFP_KERNEL, "clk:%d:%d",
+						sci_clk->dev_id,
+						sci_clk->clk_id + 1 + i);
+			if (!parent_name) {
+				ret = -ENOMEM;
+				goto err;
+			}
+			parent_names[i] = parent_name;
+		}
+		init.parent_names = (void *)parent_names;
+	}
+
+	init.ops = &sci_clk_ops;
+	init.num_parents = sci_clk->num_parents;
+	sci_clk->hw.init = &init;
+
+	ret = devm_clk_hw_register(provider->dev, &sci_clk->hw);
+	if (ret)
+		dev_err(provider->dev, "failed clk register with %d\n", ret);
+
+err:
+	if (parent_names) {
+		for (i = 0; i < sci_clk->num_parents; i++)
+			kfree(parent_names[i]);
+
+		kfree(parent_names);
+	}
+
+	kfree(name);
+
+	return ret;
+}
+
+static int _cmp_sci_clk(const void *a, const void *b)
+{
+	const struct sci_clk *ca = a;
+	const struct sci_clk *cb = *(struct sci_clk **)b;
+
+	if (ca->dev_id == cb->dev_id && ca->clk_id == cb->clk_id)
+		return 0;
+	if (ca->dev_id > cb->dev_id ||
+	    (ca->dev_id == cb->dev_id && ca->clk_id > cb->clk_id))
+		return 1;
+	return -1;
+}
+
+/**
+ * sci_clk_get - Xlate function for getting clock handles
+ * @clkspec: device tree clock specifier
+ * @data: pointer to the clock provider
+ *
+ * Xlate function for retrieving clock TI SCI hw clock handles based on
+ * device tree clock specifier. Called from the common clock framework,
+ * when a corresponding of_clk_get call is executed. Returns a pointer
+ * to the TI SCI hw clock struct, or ERR_PTR value in failure.
+ */
+static struct clk_hw *sci_clk_get(struct of_phandle_args *clkspec, void *data)
+{
+	struct sci_clk_provider *provider = data;
+	struct sci_clk **clk;
+	struct sci_clk key;
+
+	if (clkspec->args_count != 2)
+		return ERR_PTR(-EINVAL);
+
+	key.dev_id = clkspec->args[0];
+	key.clk_id = clkspec->args[1];
+
+	clk = bsearch(&key, provider->clocks, provider->num_clocks,
+		      sizeof(clk), _cmp_sci_clk);
+
+	if (!clk)
+		return ERR_PTR(-ENODEV);
+
+	return &(*clk)->hw;
+}
+
+static int ti_sci_init_clocks(struct sci_clk_provider *p)
+{
+	int i;
+	int ret;
+
+	for (i = 0; i < p->num_clocks; i++) {
+		ret = _sci_clk_build(p, p->clocks[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id ti_sci_clk_of_match[] = {
+	{ .compatible = "ti,k2g-sci-clk" },
+	{ /* Sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ti_sci_clk_of_match);
+
+#ifdef CONFIG_TI_SCI_CLK_PROBE_FROM_FW
+static int ti_sci_scan_clocks_from_fw(struct sci_clk_provider *provider)
+{
+	int ret;
+	int num_clks = 0;
+	struct sci_clk **clks = NULL;
+	struct sci_clk **tmp_clks;
+	struct sci_clk *sci_clk;
+	int max_clks = 0;
+	int clk_id = 0;
+	int dev_id = 0;
+	u32 num_parents = 0;
+	int gap_size = 0;
+	struct device *dev = provider->dev;
+
+	while (1) {
+		ret = provider->ops->get_num_parents(provider->sci, dev_id,
+						     clk_id,
+						     (void *)&num_parents);
+		if (ret) {
+			gap_size++;
+			if (!clk_id) {
+				if (gap_size >= 5)
+					break;
+				dev_id++;
+			} else {
+				if (gap_size >= 2) {
+					dev_id++;
+					clk_id = 0;
+					gap_size = 0;
+				} else {
+					clk_id++;
+				}
+			}
+			continue;
+		}
+
+		gap_size = 0;
+
+		if (num_clks == max_clks) {
+			tmp_clks = devm_kmalloc_array(dev, max_clks + 64,
+						      sizeof(sci_clk),
+						      GFP_KERNEL);
+			memcpy(tmp_clks, clks, max_clks * sizeof(sci_clk));
+			if (max_clks)
+				devm_kfree(dev, clks);
+			max_clks += 64;
+			clks = tmp_clks;
+		}
+
+		sci_clk = devm_kzalloc(dev, sizeof(*sci_clk), GFP_KERNEL);
+		if (!sci_clk)
+			return -ENOMEM;
+		sci_clk->dev_id = dev_id;
+		sci_clk->clk_id = clk_id;
+		sci_clk->provider = provider;
+		sci_clk->num_parents = num_parents;
+
+		clks[num_clks] = sci_clk;
+
+		clk_id++;
+		num_clks++;
+	}
+
+	provider->clocks = devm_kmalloc_array(dev, num_clks, sizeof(sci_clk),
+					      GFP_KERNEL);
+	if (!provider->clocks)
+		return -ENOMEM;
+
+	memcpy(provider->clocks, clks, num_clks * sizeof(sci_clk));
+
+	provider->num_clocks = num_clks;
+
+	devm_kfree(dev, clks);
+
+	return 0;
+}
+
+#else
+
+static int _cmp_sci_clk_list(void *priv, const struct list_head *a,
+			     const struct list_head *b)
+{
+	struct sci_clk *ca = container_of(a, struct sci_clk, node);
+	struct sci_clk *cb = container_of(b, struct sci_clk, node);
+
+	return _cmp_sci_clk(ca, &cb);
+}
+
+static int ti_sci_scan_clocks_from_dt(struct sci_clk_provider *provider)
+{
+	struct device *dev = provider->dev;
+	struct device_node *np = NULL;
+	int ret;
+	int index;
+	struct of_phandle_args args;
+	struct list_head clks;
+	struct sci_clk *sci_clk, *prev;
+	int num_clks = 0;
+	int num_parents;
+	int clk_id;
+	const char * const clk_names[] = {
+		"clocks", "assigned-clocks", "assigned-clock-parents", NULL
+	};
+	const char * const *clk_name;
+
+	INIT_LIST_HEAD(&clks);
+
+	clk_name = clk_names;
+
+	while (*clk_name) {
+		np = of_find_node_with_property(np, *clk_name);
+		if (!np) {
+			clk_name++;
+			continue;
+		}
+
+		if (!of_device_is_available(np))
+			continue;
+
+		index = 0;
+
+		do {
+			ret = of_parse_phandle_with_args(np, *clk_name,
+							 "#clock-cells", index,
+							 &args);
+			if (ret)
+				break;
+
+			if (args.args_count == 2 && args.np == dev->of_node) {
+				sci_clk = devm_kzalloc(dev, sizeof(*sci_clk),
+						       GFP_KERNEL);
+				if (!sci_clk)
+					return -ENOMEM;
+
+				sci_clk->dev_id = args.args[0];
+				sci_clk->clk_id = args.args[1];
+				sci_clk->provider = provider;
+				provider->ops->get_num_parents(provider->sci,
+							       sci_clk->dev_id,
+							       sci_clk->clk_id,
+							       (void *)&sci_clk->num_parents);
+				list_add_tail(&sci_clk->node, &clks);
+
+				num_clks++;
+
+				num_parents = sci_clk->num_parents;
+				if (num_parents == 1)
+					num_parents = 0;
+
+				/*
+				 * Linux kernel has inherent limitation
+				 * of 255 clock parents at the moment.
+				 * Right now, it is not expected that
+				 * any mux clock from sci-clk driver
+				 * would exceed that limit either, but
+				 * the ABI basically provides that
+				 * possibility. Print out a warning if
+				 * this happens for any clock.
+				 */
+				if (num_parents >= 255) {
+					dev_warn(dev, "too many parents for dev=%d, clk=%d (%d), cropping to 255.\n",
+						 sci_clk->dev_id,
+						 sci_clk->clk_id, num_parents);
+					num_parents = 255;
+				}
+
+				clk_id = args.args[1] + 1;
+
+				while (num_parents--) {
+					sci_clk = devm_kzalloc(dev,
+							       sizeof(*sci_clk),
+							       GFP_KERNEL);
+					if (!sci_clk)
+						return -ENOMEM;
+					sci_clk->dev_id = args.args[0];
+					sci_clk->clk_id = clk_id++;
+					sci_clk->provider = provider;
+					list_add_tail(&sci_clk->node, &clks);
+
+					num_clks++;
+				}
+			}
+
+			index++;
+		} while (args.np);
+	}
+
+	list_sort(NULL, &clks, _cmp_sci_clk_list);
+
+	provider->clocks = devm_kmalloc_array(dev, num_clks, sizeof(sci_clk),
+					      GFP_KERNEL);
+	if (!provider->clocks)
+		return -ENOMEM;
+
+	num_clks = 0;
+	prev = NULL;
+
+	list_for_each_entry(sci_clk, &clks, node) {
+		if (prev && prev->dev_id == sci_clk->dev_id &&
+		    prev->clk_id == sci_clk->clk_id)
+			continue;
+
+		provider->clocks[num_clks++] = sci_clk;
+		prev = sci_clk;
+	}
+
+	provider->num_clocks = num_clks;
+
+	return 0;
+}
+#endif
+
+/**
+ * ti_sci_clk_probe - Probe function for the TI SCI clock driver
+ * @pdev: platform device pointer to be probed
+ *
+ * Probes the TI SCI clock device. Allocates a new clock provider
+ * and registers this to the common clock framework. Also applies
+ * any required flags to the identified clocks via clock lists
+ * supplied from DT. Returns 0 for success, negative error value
+ * for failure.
+ */
+static int ti_sci_clk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct sci_clk_provider *provider;
+	const struct ti_sci_handle *handle;
+	int ret;
+
+	handle = devm_ti_sci_get_handle(dev);
+	if (IS_ERR(handle))
+		return PTR_ERR(handle);
+
+	provider = devm_kzalloc(dev, sizeof(*provider), GFP_KERNEL);
+	if (!provider)
+		return -ENOMEM;
+
+	provider->sci = handle;
+	provider->ops = &handle->ops.clk_ops;
+	provider->dev = dev;
+
+#ifdef CONFIG_TI_SCI_CLK_PROBE_FROM_FW
+	ret = ti_sci_scan_clocks_from_fw(provider);
+	if (ret) {
+		dev_err(dev, "scan clocks from FW failed: %d\n", ret);
+		return ret;
+	}
+#else
+	ret = ti_sci_scan_clocks_from_dt(provider);
+	if (ret) {
+		dev_err(dev, "scan clocks from DT failed: %d\n", ret);
+		return ret;
+	}
+#endif
+
+	ret = ti_sci_init_clocks(provider);
+	if (ret) {
+		pr_err("ti-sci-init-clocks failed.\n");
+		return ret;
+	}
+
+	return of_clk_add_hw_provider(np, sci_clk_get, provider);
+}
+
+/**
+ * ti_sci_clk_remove - Remove TI SCI clock device
+ * @pdev: platform device pointer for the device to be removed
+ *
+ * Removes the TI SCI device. Unregisters the clock provider registered
+ * via common clock framework. Any memory allocated for the device will
+ * be free'd silently via the devm framework. Returns 0 always.
+ */
+static void ti_sci_clk_remove(struct platform_device *pdev)
+{
+	of_clk_del_provider(pdev->dev.of_node);
+}
+
+static struct platform_driver ti_sci_clk_driver = {
+	.probe = ti_sci_clk_probe,
+	.remove_new = ti_sci_clk_remove,
+	.driver = {
+		.name = "ti-sci-clk",
+		.of_match_table = of_match_ptr(ti_sci_clk_of_match),
+	},
+};
+module_platform_driver(ti_sci_clk_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI System Control Interface(SCI) Clock driver");
+MODULE_AUTHOR("Tero Kristo");
+MODULE_ALIAS("platform:ti-sci-clk");
diff --git a/drivers/clk/keystone/syscon-clk.c b/drivers/clk/keystone/syscon-clk.c
new file mode 100644
index 0000000000..935d9a2d8c
--- /dev/null
+++ b/drivers/clk/keystone/syscon-clk.c
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+struct ti_syscon_gate_clk_priv {
+	struct clk_hw hw;
+	struct regmap *regmap;
+	u32 reg;
+	u32 idx;
+};
+
+struct ti_syscon_gate_clk_data {
+	char *name;
+	u32 offset;
+	u32 bit_idx;
+};
+
+static struct
+ti_syscon_gate_clk_priv *to_ti_syscon_gate_clk_priv(struct clk_hw *hw)
+{
+	return container_of(hw, struct ti_syscon_gate_clk_priv, hw);
+}
+
+static int ti_syscon_gate_clk_enable(struct clk_hw *hw)
+{
+	struct ti_syscon_gate_clk_priv *priv = to_ti_syscon_gate_clk_priv(hw);
+
+	return regmap_write_bits(priv->regmap, priv->reg, priv->idx,
+				 priv->idx);
+}
+
+static void ti_syscon_gate_clk_disable(struct clk_hw *hw)
+{
+	struct ti_syscon_gate_clk_priv *priv = to_ti_syscon_gate_clk_priv(hw);
+
+	regmap_write_bits(priv->regmap, priv->reg, priv->idx, 0);
+}
+
+static int ti_syscon_gate_clk_is_enabled(struct clk_hw *hw)
+{
+	unsigned int val;
+	struct ti_syscon_gate_clk_priv *priv = to_ti_syscon_gate_clk_priv(hw);
+
+	regmap_read(priv->regmap, priv->reg, &val);
+
+	return !!(val & priv->idx);
+}
+
+static const struct clk_ops ti_syscon_gate_clk_ops = {
+	.enable		= ti_syscon_gate_clk_enable,
+	.disable	= ti_syscon_gate_clk_disable,
+	.is_enabled	= ti_syscon_gate_clk_is_enabled,
+};
+
+static struct clk_hw
+*ti_syscon_gate_clk_register(struct device *dev, struct regmap *regmap,
+			     const char *parent_name,
+			     const struct ti_syscon_gate_clk_data *data)
+{
+	struct ti_syscon_gate_clk_priv *priv;
+	struct clk_init_data init;
+	char *name = NULL;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return ERR_PTR(-ENOMEM);
+
+	init.ops = &ti_syscon_gate_clk_ops;
+	if (parent_name) {
+		name = kasprintf(GFP_KERNEL, "%s:%s", data->name, parent_name);
+		init.name = name;
+		init.parent_names = &parent_name;
+		init.num_parents = 1;
+		init.flags = CLK_SET_RATE_PARENT;
+	} else {
+		init.name = data->name;
+		init.parent_names = NULL;
+		init.num_parents = 0;
+		init.flags = 0;
+	}
+
+	priv->regmap = regmap;
+	priv->reg = data->offset;
+	priv->idx = BIT(data->bit_idx);
+	priv->hw.init = &init;
+
+	ret = devm_clk_hw_register(dev, &priv->hw);
+
+	if (name)
+		kfree(init.name);
+
+	if (ret)
+		return ERR_PTR(ret);
+
+	return &priv->hw;
+}
+
+static int ti_syscon_gate_clk_probe(struct platform_device *pdev)
+{
+	const struct ti_syscon_gate_clk_data *data, *p;
+	struct clk_hw_onecell_data *hw_data;
+	struct device *dev = &pdev->dev;
+	int num_clks, num_parents, i;
+	const char *parent_name;
+	struct regmap *regmap;
+
+	data = device_get_match_data(dev);
+	if (!data)
+		return -EINVAL;
+
+	regmap = device_node_to_regmap(dev->of_node);
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap),
+				     "failed to get regmap\n");
+
+	num_clks = 0;
+	for (p = data; p->name; p++)
+		num_clks++;
+
+	num_parents = of_clk_get_parent_count(dev->of_node);
+	if (of_device_is_compatible(dev->of_node, "ti,am62-audio-refclk") &&
+	    num_parents == 0) {
+		return dev_err_probe(dev, -EINVAL,
+				     "must specify a parent clock\n");
+	}
+
+	hw_data = devm_kzalloc(dev, struct_size(hw_data, hws, num_clks),
+			       GFP_KERNEL);
+	if (!hw_data)
+		return -ENOMEM;
+
+	hw_data->num = num_clks;
+
+	parent_name = of_clk_get_parent_name(dev->of_node, 0);
+	for (i = 0; i < num_clks; i++) {
+		hw_data->hws[i] = ti_syscon_gate_clk_register(dev, regmap,
+							      parent_name,
+							      &data[i]);
+		if (IS_ERR(hw_data->hws[i]))
+			dev_warn(dev, "failed to register %s\n",
+				 data[i].name);
+	}
+
+	if (num_clks == 1)
+		return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
+						   hw_data->hws[0]);
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, hw_data);
+}
+
+#define TI_SYSCON_CLK_GATE(_name, _offset, _bit_idx)	\
+	{						\
+		.name = _name,				\
+		.offset = (_offset),			\
+		.bit_idx = (_bit_idx),			\
+	}
+
+static const struct ti_syscon_gate_clk_data am654_clk_data[] = {
+	TI_SYSCON_CLK_GATE("ehrpwm_tbclk0", 0x0, 0),
+	TI_SYSCON_CLK_GATE("ehrpwm_tbclk1", 0x4, 0),
+	TI_SYSCON_CLK_GATE("ehrpwm_tbclk2", 0x8, 0),
+	TI_SYSCON_CLK_GATE("ehrpwm_tbclk3", 0xc, 0),
+	TI_SYSCON_CLK_GATE("ehrpwm_tbclk4", 0x10, 0),
+	TI_SYSCON_CLK_GATE("ehrpwm_tbclk5", 0x14, 0),
+	{ /* Sentinel */ },
+};
+
+static const struct ti_syscon_gate_clk_data am64_clk_data[] = {
+	TI_SYSCON_CLK_GATE("epwm_tbclk0", 0x0, 0),
+	TI_SYSCON_CLK_GATE("epwm_tbclk1", 0x0, 1),
+	TI_SYSCON_CLK_GATE("epwm_tbclk2", 0x0, 2),
+	TI_SYSCON_CLK_GATE("epwm_tbclk3", 0x0, 3),
+	TI_SYSCON_CLK_GATE("epwm_tbclk4", 0x0, 4),
+	TI_SYSCON_CLK_GATE("epwm_tbclk5", 0x0, 5),
+	TI_SYSCON_CLK_GATE("epwm_tbclk6", 0x0, 6),
+	TI_SYSCON_CLK_GATE("epwm_tbclk7", 0x0, 7),
+	TI_SYSCON_CLK_GATE("epwm_tbclk8", 0x0, 8),
+	{ /* Sentinel */ },
+};
+
+static const struct ti_syscon_gate_clk_data am62_clk_data[] = {
+	TI_SYSCON_CLK_GATE("epwm_tbclk0", 0x0, 0),
+	TI_SYSCON_CLK_GATE("epwm_tbclk1", 0x0, 1),
+	TI_SYSCON_CLK_GATE("epwm_tbclk2", 0x0, 2),
+	{ /* Sentinel */ },
+};
+
+static const struct ti_syscon_gate_clk_data am62_audio_clk_data[] = {
+	TI_SYSCON_CLK_GATE("audio_refclk", 0x0, 15),
+	{ /* Sentinel */ },
+};
+
+static const struct of_device_id ti_syscon_gate_clk_ids[] = {
+	{
+		.compatible = "ti,am654-ehrpwm-tbclk",
+		.data = &am654_clk_data,
+	},
+	{
+		.compatible = "ti,am64-epwm-tbclk",
+		.data = &am64_clk_data,
+	},
+	{
+		.compatible = "ti,am62-epwm-tbclk",
+		.data = &am62_clk_data,
+	},
+	{
+		.compatible = "ti,am62-audio-refclk",
+		.data = &am62_audio_clk_data,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ti_syscon_gate_clk_ids);
+
+static struct platform_driver ti_syscon_gate_clk_driver = {
+	.probe = ti_syscon_gate_clk_probe,
+	.driver = {
+		.name = "ti-syscon-gate-clk",
+		.of_match_table = ti_syscon_gate_clk_ids,
+	},
+};
+module_platform_driver(ti_syscon_gate_clk_driver);
+
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
+MODULE_DESCRIPTION("Syscon backed gate-clock driver");
+MODULE_LICENSE("GPL");