Merging upstream version 6.7.7.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1513 insertions, 0 deletions

diff --git a/drivers/iio/adc/mcp3564.c b/drivers/iio/adc/mcp3564.c
new file mode 100644
index 0000000000..311b613b60
--- /dev/null
+++ b/drivers/iio/adc/mcp3564.c
@@ -0,0 +1,1513 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * IIO driver for MCP356X/MCP356XR and MCP346X/MCP346XR series ADC chip family
+ *
+ * Copyright (C) 2022-2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Marius Cristea <marius.cristea@microchip.com>
+ *
+ * Datasheet for MCP3561, MCP3562, MCP3564 can be found here:
+ * https://ww1.microchip.com/downloads/aemDocuments/documents/MSLD/ProductDocuments/DataSheets/MCP3561-2-4-Family-Data-Sheet-DS20006181C.pdf
+ * Datasheet for MCP3561R, MCP3562R, MCP3564R can be found here:
+ * https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP3561_2_4R-Data-Sheet-DS200006391C.pdf
+ * Datasheet for MCP3461, MCP3462, MCP3464 can be found here:
+ * https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP3461-2-4-Two-Four-Eight-Channel-153.6-ksps-Low-Noise-16-Bit-Delta-Sigma-ADC-Data-Sheet-20006180D.pdf
+ * Datasheet for MCP3461R, MCP3462R, MCP3464R can be found here:
+ * https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP3461-2-4R-Family-Data-Sheet-DS20006404C.pdf
+ */
+
+#include <linux/bitfield.h>
+#include <linux/iopoll.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+#include <linux/units.h>
+#include <linux/util_macros.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+#define MCP3564_ADCDATA_REG		0x00
+
+#define MCP3564_CONFIG0_REG		0x01
+#define MCP3564_CONFIG0_ADC_MODE_MASK		GENMASK(1, 0)
+/* Current Source/Sink Selection Bits for Sensor Bias */
+#define MCP3564_CONFIG0_CS_SEL_MASK		GENMASK(3, 2)
+/* Internal clock is selected and AMCLK is present on the analog master clock output pin */
+#define MCP3564_CONFIG0_USE_INT_CLK_OUTPUT_EN	0x03
+/* Internal clock is selected and no clock output is present on the CLK pin */
+#define MCP3564_CONFIG0_USE_INT_CLK		0x02
+/* External digital clock */
+#define MCP3564_CONFIG0_USE_EXT_CLK		0x01
+/* External digital clock (default) */
+#define MCP3564_CONFIG0_USE_EXT_CLK_DEFAULT	0x00
+#define MCP3564_CONFIG0_CLK_SEL_MASK		GENMASK(5, 4)
+#define MCP3456_CONFIG0_BIT6_DEFAULT		BIT(6)
+#define MCP3456_CONFIG0_VREF_MASK		BIT(7)
+
+#define MCP3564_CONFIG1_REG		0x02
+#define MCP3564_CONFIG1_OVERSPL_RATIO_MASK	GENMASK(5, 2)
+
+#define MCP3564_CONFIG2_REG		0x03
+#define MCP3564_CONFIG2_AZ_REF_MASK		BIT(1)
+#define MCP3564_CONFIG2_AZ_MUX_MASK		BIT(2)
+
+#define MCP3564_CONFIG2_HARDWARE_GAIN_MASK	GENMASK(5, 3)
+#define MCP3564_DEFAULT_HARDWARE_GAIN		0x01
+#define MCP3564_CONFIG2_BOOST_CURRENT_MASK	GENMASK(7, 6)
+
+#define MCP3564_CONFIG3_REG		0x04
+#define MCP3464_CONFIG3_EN_GAINCAL_MASK		BIT(0)
+#define MCP3464_CONFIG3_EN_OFFCAL_MASK		BIT(1)
+#define MCP3464_CONFIG3_EN_CRCCOM_MASK		BIT(2)
+#define MCP3464_CONFIG3_CRC_FORMAT_MASK		BIT(3)
+/*
+ * ADC Output Data Format 32-bit (25-bit right justified data + Channel ID):
+ *                CHID[3:0] + SGN extension (4 bits) + 24-bit ADC data.
+ *        It allows overrange with the SGN extension.
+ */
+#define MCP3464_CONFIG3_DATA_FMT_32B_WITH_CH_ID		3
+/*
+ * ADC Output Data Format 32-bit (25-bit right justified data):
+ *                SGN extension (8-bit) + 24-bit ADC data.
+ *        It allows overrange with the SGN extension.
+ */
+#define MCP3464_CONFIG3_DATA_FMT_32B_SGN_EXT		2
+/*
+ * ADC Output Data Format 32-bit (24-bit left justified data):
+ *                24-bit ADC data + 0x00 (8-bit).
+ *        It does not allow overrange (ADC code locked to 0xFFFFFF or 0x800000).
+ */
+#define MCP3464_CONFIG3_DATA_FMT_32B_LEFT_JUSTIFIED	1
+/*
+ * ADC Output Data Format 24-bit (default ADC coding):
+ *                24-bit ADC data.
+ *        It does not allow overrange (ADC code locked to 0xFFFFFF or 0x800000).
+ */
+#define MCP3464_CONFIG3_DATA_FMT_24B			0
+#define MCP3464_CONFIG3_DATA_FORMAT_MASK	GENMASK(5, 4)
+
+/* Continuous Conversion mode or continuous conversion cycle in SCAN mode. */
+#define MCP3464_CONFIG3_CONV_MODE_CONTINUOUS		3
+/*
+ * One-shot conversion or one-shot cycle in SCAN mode. It sets ADC_MODE[1:0] to ‘10’
+ * (standby) at the end of the conversion or at the end of the conversion cycle in SCAN mode.
+ */
+#define MCP3464_CONFIG3_CONV_MODE_ONE_SHOT_STANDBY	2
+/*
+ * One-shot conversion or one-shot cycle in SCAN mode. It sets ADC_MODE[1:0] to ‘0x’ (ADC
+ * Shutdown) at the end of the conversion or at the end of the conversion cycle in SCAN
+ * mode (default).
+ */
+#define MCP3464_CONFIG3_CONV_MODE_ONE_SHOT_SHUTDOWN	0
+#define MCP3464_CONFIG3_CONV_MODE_MASK		GENMASK(7, 6)
+
+#define MCP3564_IRQ_REG			0x05
+#define MCP3464_EN_STP_MASK			BIT(0)
+#define MCP3464_EN_FASTCMD_MASK			BIT(1)
+#define MCP3464_IRQ_MODE_0_MASK			BIT(2)
+#define MCP3464_IRQ_MODE_1_MASK			BIT(3)
+#define MCP3564_POR_STATUS_MASK			BIT(4)
+#define MCP3564_CRCCFG_STATUS_MASK		BIT(5)
+#define MCP3564_DATA_READY_MASK			BIT(6)
+
+#define MCP3564_MUX_REG			0x06
+#define MCP3564_MUX_VIN_P_MASK			GENMASK(7, 4)
+#define MCP3564_MUX_VIN_N_MASK			GENMASK(3, 0)
+#define MCP3564_MUX_SET(x, y)			(FIELD_PREP(MCP3564_MUX_VIN_P_MASK, (x)) |	\
+						FIELD_PREP(MCP3564_MUX_VIN_N_MASK, (y)))
+
+#define MCP3564_SCAN_REG		0x07
+#define MCP3564_SCAN_CH_SEL_MASK		GENMASK(15, 0)
+#define MCP3564_SCAN_CH_SEL_SET(x)		FIELD_PREP(MCP3564_SCAN_CH_SEL_MASK, (x))
+#define MCP3564_SCAN_DELAY_TIME_MASK		GENMASK(23, 21)
+#define MCP3564_SCAN_DELAY_TIME_SET(x)		FIELD_PREP(MCP3564_SCAN_DELAY_TIME_MASK, (x))
+#define MCP3564_SCAN_DEFAULT_VALUE		0
+
+#define MCP3564_TIMER_REG		0x08
+#define MCP3564_TIMER_DEFAULT_VALUE		0
+
+#define MCP3564_OFFSETCAL_REG		0x09
+#define MCP3564_DEFAULT_OFFSETCAL		0
+
+#define MCP3564_GAINCAL_REG		0x0A
+#define MCP3564_DEFAULT_GAINCAL			0x00800000
+
+#define MCP3564_RESERVED_B_REG		0x0B
+
+#define MCP3564_RESERVED_C_REG		0x0C
+#define MCP3564_C_REG_DEFAULT			0x50
+#define MCP3564R_C_REG_DEFAULT			0x30
+
+#define MCP3564_LOCK_REG		0x0D
+#define MCP3564_LOCK_WRITE_ACCESS_PASSWORD	0xA5
+#define MCP3564_RESERVED_E_REG		0x0E
+#define MCP3564_CRCCFG_REG		0x0F
+
+#define MCP3564_CMD_HW_ADDR_MASK	GENMASK(7, 6)
+#define MCP3564_CMD_ADDR_MASK		GENMASK(5, 2)
+
+#define MCP3564_HW_ADDR_MASK		GENMASK(1, 0)
+
+#define MCP3564_FASTCMD_START	0x0A
+#define MCP3564_FASTCMD_RESET	0x0E
+
+#define MCP3461_HW_ID		0x0008
+#define MCP3462_HW_ID		0x0009
+#define MCP3464_HW_ID		0x000B
+
+#define MCP3561_HW_ID		0x000C
+#define MCP3562_HW_ID		0x000D
+#define MCP3564_HW_ID		0x000F
+#define MCP3564_HW_ID_MASK	GENMASK(3, 0)
+
+#define MCP3564R_INT_VREF_MV	2400
+
+#define MCP3564_DATA_READY_TIMEOUT_MS	2000
+
+#define MCP3564_MAX_PGA				8
+#define MCP3564_MAX_BURNOUT_IDX			4
+#define MCP3564_MAX_CHANNELS			66
+
+enum mcp3564_ids {
+	mcp3461,
+	mcp3462,
+	mcp3464,
+	mcp3561,
+	mcp3562,
+	mcp3564,
+	mcp3461r,
+	mcp3462r,
+	mcp3464r,
+	mcp3561r,
+	mcp3562r,
+	mcp3564r,
+};
+
+enum mcp3564_delay_time {
+	MCP3564_NO_DELAY,
+	MCP3564_DELAY_8_DMCLK,
+	MCP3564_DELAY_16_DMCLK,
+	MCP3564_DELAY_32_DMCLK,
+	MCP3564_DELAY_64_DMCLK,
+	MCP3564_DELAY_128_DMCLK,
+	MCP3564_DELAY_256_DMCLK,
+	MCP3564_DELAY_512_DMCLK
+};
+
+enum mcp3564_adc_conversion_mode {
+	MCP3564_ADC_MODE_DEFAULT,
+	MCP3564_ADC_MODE_SHUTDOWN,
+	MCP3564_ADC_MODE_STANDBY,
+	MCP3564_ADC_MODE_CONVERSION
+};
+
+enum mcp3564_adc_bias_current {
+	MCP3564_BOOST_CURRENT_x0_50,
+	MCP3564_BOOST_CURRENT_x0_66,
+	MCP3564_BOOST_CURRENT_x1_00,
+	MCP3564_BOOST_CURRENT_x2_00
+};
+
+enum mcp3564_burnout {
+	MCP3564_CONFIG0_CS_SEL_0_0_uA,
+	MCP3564_CONFIG0_CS_SEL_0_9_uA,
+	MCP3564_CONFIG0_CS_SEL_3_7_uA,
+	MCP3564_CONFIG0_CS_SEL_15_uA
+};
+
+enum mcp3564_channel_names {
+	MCP3564_CH0,
+	MCP3564_CH1,
+	MCP3564_CH2,
+	MCP3564_CH3,
+	MCP3564_CH4,
+	MCP3564_CH5,
+	MCP3564_CH6,
+	MCP3564_CH7,
+	MCP3564_AGND,
+	MCP3564_AVDD,
+	MCP3564_RESERVED, /* do not use */
+	MCP3564_REFIN_POZ,
+	MCP3564_REFIN_NEG,
+	MCP3564_TEMP_DIODE_P,
+	MCP3564_TEMP_DIODE_M,
+	MCP3564_INTERNAL_VCM,
+};
+
+enum mcp3564_oversampling {
+	MCP3564_OVERSAMPLING_RATIO_32,
+	MCP3564_OVERSAMPLING_RATIO_64,
+	MCP3564_OVERSAMPLING_RATIO_128,
+	MCP3564_OVERSAMPLING_RATIO_256,
+	MCP3564_OVERSAMPLING_RATIO_512,
+	MCP3564_OVERSAMPLING_RATIO_1024,
+	MCP3564_OVERSAMPLING_RATIO_2048,
+	MCP3564_OVERSAMPLING_RATIO_4096,
+	MCP3564_OVERSAMPLING_RATIO_8192,
+	MCP3564_OVERSAMPLING_RATIO_16384,
+	MCP3564_OVERSAMPLING_RATIO_20480,
+	MCP3564_OVERSAMPLING_RATIO_24576,
+	MCP3564_OVERSAMPLING_RATIO_40960,
+	MCP3564_OVERSAMPLING_RATIO_49152,
+	MCP3564_OVERSAMPLING_RATIO_81920,
+	MCP3564_OVERSAMPLING_RATIO_98304
+};
+
+static const unsigned int mcp3564_oversampling_avail[] = {
+	[MCP3564_OVERSAMPLING_RATIO_32] = 32,
+	[MCP3564_OVERSAMPLING_RATIO_64] = 64,
+	[MCP3564_OVERSAMPLING_RATIO_128] = 128,
+	[MCP3564_OVERSAMPLING_RATIO_256] = 256,
+	[MCP3564_OVERSAMPLING_RATIO_512] = 512,
+	[MCP3564_OVERSAMPLING_RATIO_1024] = 1024,
+	[MCP3564_OVERSAMPLING_RATIO_2048] = 2048,
+	[MCP3564_OVERSAMPLING_RATIO_4096] = 4096,
+	[MCP3564_OVERSAMPLING_RATIO_8192] = 8192,
+	[MCP3564_OVERSAMPLING_RATIO_16384] = 16384,
+	[MCP3564_OVERSAMPLING_RATIO_20480] = 20480,
+	[MCP3564_OVERSAMPLING_RATIO_24576] = 24576,
+	[MCP3564_OVERSAMPLING_RATIO_40960] = 40960,
+	[MCP3564_OVERSAMPLING_RATIO_49152] = 49152,
+	[MCP3564_OVERSAMPLING_RATIO_81920] = 81920,
+	[MCP3564_OVERSAMPLING_RATIO_98304] = 98304
+};
+
+/*
+ * Current Source/Sink Selection Bits for Sensor Bias (source on VIN+/sink on VIN-)
+ */
+static const int mcp3564_burnout_avail[][2] = {
+	[MCP3564_CONFIG0_CS_SEL_0_0_uA] = { 0, 0 },
+	[MCP3564_CONFIG0_CS_SEL_0_9_uA] = { 0, 900 },
+	[MCP3564_CONFIG0_CS_SEL_3_7_uA] = { 0, 3700 },
+	[MCP3564_CONFIG0_CS_SEL_15_uA] = { 0, 15000 }
+};
+
+/*
+ * BOOST[1:0]: ADC Bias Current Selection
+ */
+static const char * const mcp3564_boost_current_avail[] = {
+	[MCP3564_BOOST_CURRENT_x0_50] = "0.5",
+	[MCP3564_BOOST_CURRENT_x0_66] = "0.66",
+	[MCP3564_BOOST_CURRENT_x1_00] = "1",
+	[MCP3564_BOOST_CURRENT_x2_00] = "2",
+};
+
+/*
+ * Calibration bias values
+ */
+static const int mcp3564_calib_bias[] = {
+	-8388608,	/* min: -2^23		*/
+	 1,		/* step: 1		*/
+	 8388607	/* max:  2^23 - 1	*/
+};
+
+/*
+ * Calibration scale values
+ * The Gain Error Calibration register (GAINCAL) is an
+ * unsigned 24-bit register that holds the digital gain error
+ * calibration value, GAINCAL which could be calculated by
+ * GAINCAL (V/V) = (GAINCAL[23:0])/8388608
+ * The gain error calibration value range in equivalent voltage is [0; 2-2^(-23)]
+ */
+static const unsigned int mcp3564_calib_scale[] = {
+	0,		/* min:  0		*/
+	1,		/* step: 1/8388608	*/
+	16777215	/* max:  2 - 2^(-23)	*/
+};
+
+/* Programmable hardware gain x1/3, x1, x2, x4, x8, x16, x32, x64 */
+static const int mcp3564_hwgain_frac[] = {
+	3, 10,
+	1, 1,
+	2, 1,
+	4, 1,
+	8, 1,
+	16, 1,
+	32, 1,
+	64, 1
+};
+
+static const char *mcp3564_channel_labels[2] = {
+	"burnout_current", "temperature",
+};
+
+/**
+ * struct mcp3564_chip_info - chip specific data
+ * @name:		device name
+ * @num_channels:	number of channels
+ * @resolution:		ADC resolution
+ * @have_vref:		does the hardware have an internal voltage reference?
+ */
+struct mcp3564_chip_info {
+	const char	*name;
+	unsigned int	num_channels;
+	unsigned int	resolution;
+	bool		have_vref;
+};
+
+/**
+ * struct mcp3564_state - working data for a ADC device
+ * @chip_info:		chip specific data
+ * @spi:		SPI device structure
+ * @vref:		the regulator device used as a voltage reference in case
+ *			external voltage reference is used
+ * @vref_mv:		voltage reference value in miliVolts
+ * @lock:		synchronize access to driver's state members
+ * @dev_addr:		hardware device address
+ * @oversampling:	the index inside oversampling list of the ADC
+ * @hwgain:		the index inside hardware gain list of the ADC
+ * @scale_tbls:		table with precalculated scale
+ * @calib_bias:		calibration bias value
+ * @calib_scale:	calibration scale value
+ * @current_boost_mode:	the index inside current boost list of the ADC
+ * @burnout_mode:	the index inside current bias list of the ADC
+ * @auto_zeroing_mux:	set if ADC auto-zeroing algorithm is enabled
+ * @auto_zeroing_ref:	set if ADC auto-Zeroing Reference Buffer Setting is enabled
+ * @have_vref:		does the ADC have an internal voltage reference?
+ * @labels:		table with channels labels
+ */
+struct mcp3564_state {
+	const struct mcp3564_chip_info	*chip_info;
+	struct spi_device		*spi;
+	struct regulator		*vref;
+	unsigned short			vref_mv;
+	struct mutex			lock; /* Synchronize access to driver's state members */
+	u8				dev_addr;
+	enum mcp3564_oversampling	oversampling;
+	unsigned int			hwgain;
+	unsigned int			scale_tbls[MCP3564_MAX_PGA][2];
+	int				calib_bias;
+	int				calib_scale;
+	unsigned int			current_boost_mode;
+	enum mcp3564_burnout		burnout_mode;
+	bool				auto_zeroing_mux;
+	bool				auto_zeroing_ref;
+	bool				have_vref;
+	const char			*labels[MCP3564_MAX_CHANNELS];
+};
+
+static inline u8 mcp3564_cmd_write(u8 chip_addr, u8 reg)
+{
+	return FIELD_PREP(MCP3564_CMD_HW_ADDR_MASK, chip_addr) |
+	       FIELD_PREP(MCP3564_CMD_ADDR_MASK, reg) |
+	       BIT(1);
+}
+
+static inline u8 mcp3564_cmd_read(u8 chip_addr, u8 reg)
+{
+	return FIELD_PREP(MCP3564_CMD_HW_ADDR_MASK, chip_addr) |
+	       FIELD_PREP(MCP3564_CMD_ADDR_MASK, reg) |
+	       BIT(0);
+}
+
+static int mcp3564_read_8bits(struct mcp3564_state *adc, u8 reg, u8 *val)
+{
+	int ret;
+	u8 tx_buf;
+	u8 rx_buf;
+
+	tx_buf = mcp3564_cmd_read(adc->dev_addr, reg);
+
+	ret = spi_write_then_read(adc->spi, &tx_buf, sizeof(tx_buf),
+				  &rx_buf, sizeof(rx_buf));
+	*val = rx_buf;
+
+	return ret;
+}
+
+static int mcp3564_read_16bits(struct mcp3564_state *adc, u8 reg, u16 *val)
+{
+	int ret;
+	u8 tx_buf;
+	__be16 rx_buf;
+
+	tx_buf = mcp3564_cmd_read(adc->dev_addr, reg);
+
+	ret = spi_write_then_read(adc->spi, &tx_buf, sizeof(tx_buf),
+				  &rx_buf, sizeof(rx_buf));
+	*val = be16_to_cpu(rx_buf);
+
+	return ret;
+}
+
+static int mcp3564_read_32bits(struct mcp3564_state *adc, u8 reg, u32 *val)
+{
+	int ret;
+	u8 tx_buf;
+	__be32 rx_buf;
+
+	tx_buf = mcp3564_cmd_read(adc->dev_addr, reg);
+
+	ret = spi_write_then_read(adc->spi, &tx_buf, sizeof(tx_buf),
+				  &rx_buf, sizeof(rx_buf));
+	*val = be32_to_cpu(rx_buf);
+
+	return ret;
+}
+
+static int mcp3564_write_8bits(struct mcp3564_state *adc, u8 reg, u8 val)
+{
+	u8 tx_buf[2];
+
+	tx_buf[0] = mcp3564_cmd_write(adc->dev_addr, reg);
+	tx_buf[1] = val;
+
+	return spi_write_then_read(adc->spi, tx_buf, sizeof(tx_buf), NULL, 0);
+}
+
+static int mcp3564_write_24bits(struct mcp3564_state *adc, u8 reg, u32 val)
+{
+	__be32 val_be;
+
+	val |= (mcp3564_cmd_write(adc->dev_addr, reg) << 24);
+	val_be = cpu_to_be32(val);
+
+	return spi_write_then_read(adc->spi, &val_be, sizeof(val_be), NULL, 0);
+}
+
+static int mcp3564_fast_cmd(struct mcp3564_state *adc, u8 fast_cmd)
+{
+	u8 val;
+
+	val = FIELD_PREP(MCP3564_CMD_HW_ADDR_MASK, adc->dev_addr) |
+			 FIELD_PREP(MCP3564_CMD_ADDR_MASK, fast_cmd);
+
+	return spi_write_then_read(adc->spi, &val, 1, NULL, 0);
+}
+
+static int mcp3564_update_8bits(struct mcp3564_state *adc, u8 reg, u32 mask, u8 val)
+{
+	u8 tmp;
+	int ret;
+
+	val &= mask;
+
+	ret = mcp3564_read_8bits(adc, reg, &tmp);
+	if (ret < 0)
+		return ret;
+
+	tmp &= ~mask;
+	tmp |= val;
+
+	return mcp3564_write_8bits(adc, reg, tmp);
+}
+
+static int mcp3564_set_current_boost_mode(struct iio_dev *indio_dev,
+					  const struct iio_chan_spec *chan,
+					  unsigned int mode)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	int ret;
+
+	dev_dbg(&indio_dev->dev, "%s: %d\n", __func__, mode);
+
+	mutex_lock(&adc->lock);
+	ret = mcp3564_update_8bits(adc, MCP3564_CONFIG2_REG, MCP3564_CONFIG2_BOOST_CURRENT_MASK,
+				   FIELD_PREP(MCP3564_CONFIG2_BOOST_CURRENT_MASK, mode));
+
+	if (ret)
+		dev_err(&indio_dev->dev, "Failed to configure CONFIG2 register\n");
+	else
+		adc->current_boost_mode = mode;
+
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
+static int mcp3564_get_current_boost_mode(struct iio_dev *indio_dev,
+					  const struct iio_chan_spec *chan)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+
+	return adc->current_boost_mode;
+}
+
+static const struct iio_enum mcp3564_current_boost_mode_enum = {
+	.items = mcp3564_boost_current_avail,
+	.num_items = ARRAY_SIZE(mcp3564_boost_current_avail),
+	.set = mcp3564_set_current_boost_mode,
+	.get = mcp3564_get_current_boost_mode,
+};
+
+static const struct iio_chan_spec_ext_info mcp3564_ext_info[] = {
+	IIO_ENUM("boost_current_gain", IIO_SHARED_BY_ALL, &mcp3564_current_boost_mode_enum),
+	{
+		.name = "boost_current_gain_available",
+		.shared = IIO_SHARED_BY_ALL,
+		.read = iio_enum_available_read,
+		.private = (uintptr_t)&mcp3564_current_boost_mode_enum,
+	},
+	{ }
+};
+
+static ssize_t mcp3564_auto_zeroing_mux_show(struct device *dev,
+					     struct device_attribute *attr,
+					     char *buf)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+
+	return sysfs_emit(buf, "%d\n", adc->auto_zeroing_mux);
+}
+
+static ssize_t mcp3564_auto_zeroing_mux_store(struct device *dev,
+					      struct device_attribute *attr,
+					      const char *buf, size_t len)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	bool auto_zero;
+	int ret;
+
+	ret = kstrtobool(buf, &auto_zero);
+	if (ret)
+		return ret;
+
+	mutex_lock(&adc->lock);
+	ret = mcp3564_update_8bits(adc, MCP3564_CONFIG2_REG, MCP3564_CONFIG2_AZ_MUX_MASK,
+				   FIELD_PREP(MCP3564_CONFIG2_AZ_MUX_MASK, auto_zero));
+
+	if (ret)
+		dev_err(&indio_dev->dev, "Failed to update CONFIG2 register\n");
+	else
+		adc->auto_zeroing_mux = auto_zero;
+
+	mutex_unlock(&adc->lock);
+
+	return ret ? ret : len;
+}
+
+static ssize_t mcp3564_auto_zeroing_ref_show(struct device *dev,
+					     struct device_attribute *attr,
+					     char *buf)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+
+	return sysfs_emit(buf, "%d\n", adc->auto_zeroing_ref);
+}
+
+static ssize_t mcp3564_auto_zeroing_ref_store(struct device *dev,
+					      struct device_attribute *attr,
+					      const char *buf, size_t len)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	bool auto_zero;
+	int ret;
+
+	ret = kstrtobool(buf, &auto_zero);
+	if (ret)
+		return ret;
+
+	mutex_lock(&adc->lock);
+	ret = mcp3564_update_8bits(adc, MCP3564_CONFIG2_REG, MCP3564_CONFIG2_AZ_REF_MASK,
+				   FIELD_PREP(MCP3564_CONFIG2_AZ_REF_MASK, auto_zero));
+
+	if (ret)
+		dev_err(&indio_dev->dev, "Failed to update CONFIG2 register\n");
+	else
+		adc->auto_zeroing_ref = auto_zero;
+
+	mutex_unlock(&adc->lock);
+
+	return ret ? ret : len;
+}
+
+static const struct iio_chan_spec mcp3564_channel_template = {
+	.type = IIO_VOLTAGE,
+	.indexed = 1,
+	.differential = 1,
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+	.info_mask_shared_by_all  = BIT(IIO_CHAN_INFO_SCALE)		|
+				BIT(IIO_CHAN_INFO_CALIBSCALE)		|
+				BIT(IIO_CHAN_INFO_CALIBBIAS)		|
+				BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	.info_mask_shared_by_all_available = BIT(IIO_CHAN_INFO_SCALE)	|
+				BIT(IIO_CHAN_INFO_CALIBSCALE) |
+				BIT(IIO_CHAN_INFO_CALIBBIAS)		|
+				BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	.ext_info = mcp3564_ext_info,
+};
+
+static const struct iio_chan_spec mcp3564_temp_channel_template = {
+	.type = IIO_TEMP,
+	.channel = 0,
+	.address = ((MCP3564_TEMP_DIODE_P << 4) | MCP3564_TEMP_DIODE_M),
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+	.info_mask_shared_by_all  = BIT(IIO_CHAN_INFO_SCALE)		|
+			BIT(IIO_CHAN_INFO_CALIBSCALE)			|
+			BIT(IIO_CHAN_INFO_CALIBBIAS)			|
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	.info_mask_shared_by_all_available = BIT(IIO_CHAN_INFO_SCALE)	|
+			BIT(IIO_CHAN_INFO_CALIBSCALE) |
+			BIT(IIO_CHAN_INFO_CALIBBIAS)			|
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+};
+
+static const struct iio_chan_spec mcp3564_burnout_channel_template = {
+	.type = IIO_CURRENT,
+	.output = true,
+	.channel = 0,
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+	.info_mask_separate_available = BIT(IIO_CHAN_INFO_RAW),
+};
+
+/*
+ * Number of channels could be calculated:
+ * num_channels = single_ended_input + differential_input + temperature + burnout
+ * Eg. for MCP3561 (only 2 channels available: CH0 and CH1)
+ * single_ended_input = (CH0 - GND), (CH1 -  GND) = 2
+ * differential_input = (CH0 - CH1), (CH0 -  CH0) = 2
+ * num_channels = 2 + 2 + 2
+ * Generic formula is:
+ * num_channels = P^R(Number_of_single_ended_channels, 2) + 2 (temperature + burnout channels)
+ * P^R(Number_of_single_ended_channels, 2) is Permutations with Replacement of
+ *     Number_of_single_ended_channels taken by 2
+ */
+static const struct mcp3564_chip_info mcp3564_chip_infos_tbl[] = {
+	[mcp3461] = {
+		.name = "mcp3461",
+		.num_channels = 6,
+		.resolution = 16,
+		.have_vref = false,
+	},
+	[mcp3462] = {
+		.name = "mcp3462",
+		.num_channels = 18,
+		.resolution = 16,
+		.have_vref = false,
+	},
+	[mcp3464] = {
+		.name = "mcp3464",
+		.num_channels = 66,
+		.resolution = 16,
+		.have_vref = false,
+	},
+	[mcp3561] = {
+		.name = "mcp3561",
+		.num_channels = 6,
+		.resolution = 24,
+		.have_vref = false,
+	},
+	[mcp3562] = {
+		.name = "mcp3562",
+		.num_channels = 18,
+		.resolution = 24,
+		.have_vref = false,
+	},
+	[mcp3564] = {
+		.name = "mcp3564",
+		.num_channels = 66,
+		.resolution = 24,
+		.have_vref = false,
+	},
+	[mcp3461r] = {
+		.name = "mcp3461r",
+		.num_channels = 6,
+		.resolution = 16,
+		.have_vref = false,
+	},
+	[mcp3462r] = {
+		.name = "mcp3462r",
+		.num_channels = 18,
+		.resolution = 16,
+		.have_vref = true,
+	},
+	[mcp3464r] = {
+		.name = "mcp3464r",
+		.num_channels = 66,
+		.resolution = 16,
+		.have_vref = true,
+	},
+	[mcp3561r] = {
+		.name = "mcp3561r",
+		.num_channels = 6,
+		.resolution = 24,
+		.have_vref = true,
+	},
+	[mcp3562r] = {
+		.name = "mcp3562r",
+		.num_channels = 18,
+		.resolution = 24,
+		.have_vref = true,
+	},
+	[mcp3564r] = {
+		.name = "mcp3564r",
+		.num_channels = 66,
+		.resolution = 24,
+		.have_vref = true,
+	},
+};
+
+static int mcp3564_read_single_value(struct iio_dev *indio_dev,
+				     struct iio_chan_spec const *channel,
+				     int *val)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	int ret;
+	u8 tmp;
+	int ret_read = 0;
+
+	ret = mcp3564_write_8bits(adc, MCP3564_MUX_REG, channel->address);
+	if (ret)
+		return ret;
+
+	/* Start ADC Conversion using fast command (overwrites ADC_MODE[1:0] = 11) */
+	ret = mcp3564_fast_cmd(adc, MCP3564_FASTCMD_START);
+	if (ret)
+		return ret;
+
+	/*
+	 * Check if the conversion is ready. If not, wait a little bit, and
+	 * in case of timeout exit with an error.
+	 */
+	ret = read_poll_timeout(mcp3564_read_8bits, ret_read,
+				ret_read || !(tmp & MCP3564_DATA_READY_MASK),
+				20000, MCP3564_DATA_READY_TIMEOUT_MS * 1000, true,
+				adc, MCP3564_IRQ_REG, &tmp);
+
+	/* failed to read status register */
+	if (ret_read)
+		return ret_read;
+
+	if (ret)
+		return ret;
+
+	if (tmp & MCP3564_DATA_READY_MASK)
+		/* failing to finish conversion */
+		return -EBUSY;
+
+	return mcp3564_read_32bits(adc, MCP3564_ADCDATA_REG, val);
+}
+
+static int mcp3564_read_avail(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *channel,
+			      const int **vals, int *type,
+			      int *length, long mask)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		if (!channel->output)
+			return -EINVAL;
+
+		*vals = mcp3564_burnout_avail[0];
+		*length = ARRAY_SIZE(mcp3564_burnout_avail) * 2;
+		*type = IIO_VAL_INT_PLUS_MICRO;
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		*vals = mcp3564_oversampling_avail;
+		*length = ARRAY_SIZE(mcp3564_oversampling_avail);
+		*type = IIO_VAL_INT;
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_SCALE:
+		*vals = (int *)adc->scale_tbls;
+		*length = ARRAY_SIZE(adc->scale_tbls) * 2;
+		*type = IIO_VAL_INT_PLUS_NANO;
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		*vals = mcp3564_calib_bias;
+		*type = IIO_VAL_INT;
+		return IIO_AVAIL_RANGE;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		*vals = mcp3564_calib_scale;
+		*type = IIO_VAL_INT;
+		return IIO_AVAIL_RANGE;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mcp3564_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *channel,
+			    int *val, int *val2, long mask)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		if (channel->output) {
+			mutex_lock(&adc->lock);
+			*val = mcp3564_burnout_avail[adc->burnout_mode][0];
+			*val2 = mcp3564_burnout_avail[adc->burnout_mode][1];
+			mutex_unlock(&adc->lock);
+			return IIO_VAL_INT_PLUS_MICRO;
+		}
+
+		ret = mcp3564_read_single_value(indio_dev, channel, val);
+		if (ret)
+			return -EINVAL;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		mutex_lock(&adc->lock);
+		*val = adc->scale_tbls[adc->hwgain][0];
+		*val2 = adc->scale_tbls[adc->hwgain][1];
+		mutex_unlock(&adc->lock);
+		return IIO_VAL_INT_PLUS_NANO;
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		*val = mcp3564_oversampling_avail[adc->oversampling];
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		*val = adc->calib_bias;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		*val = adc->calib_scale;
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mcp3564_write_raw_get_fmt(struct iio_dev *indio_dev,
+				     struct iio_chan_spec const *chan,
+				     long info)
+{
+	switch (info) {
+	case IIO_CHAN_INFO_RAW:
+		return IIO_VAL_INT_PLUS_MICRO;
+	case IIO_CHAN_INFO_CALIBBIAS:
+	case IIO_CHAN_INFO_CALIBSCALE:
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		return IIO_VAL_INT_PLUS_NANO;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mcp3564_write_raw(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *channel, int val,
+			     int val2, long mask)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	int tmp;
+	unsigned int hwgain;
+	enum mcp3564_burnout burnout;
+	int ret = 0;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		if (!channel->output)
+			return -EINVAL;
+
+		for (burnout = 0; burnout < MCP3564_MAX_BURNOUT_IDX; burnout++)
+			if (val == mcp3564_burnout_avail[burnout][0] &&
+			    val2 == mcp3564_burnout_avail[burnout][1])
+				break;
+
+		if (burnout == MCP3564_MAX_BURNOUT_IDX)
+			return -EINVAL;
+
+		if (burnout == adc->burnout_mode)
+			return ret;
+
+		mutex_lock(&adc->lock);
+		ret = mcp3564_update_8bits(adc, MCP3564_CONFIG0_REG,
+					   MCP3564_CONFIG0_CS_SEL_MASK,
+					   FIELD_PREP(MCP3564_CONFIG0_CS_SEL_MASK, burnout));
+
+		if (ret)
+			dev_err(&indio_dev->dev, "Failed to configure burnout current\n");
+		else
+			adc->burnout_mode = burnout;
+		mutex_unlock(&adc->lock);
+		return ret;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		if (val < mcp3564_calib_bias[0] || val > mcp3564_calib_bias[2])
+			return -EINVAL;
+
+		mutex_lock(&adc->lock);
+		ret = mcp3564_write_24bits(adc, MCP3564_OFFSETCAL_REG, val);
+		if (!ret)
+			adc->calib_bias = val;
+		mutex_unlock(&adc->lock);
+		return ret;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		if (val < mcp3564_calib_scale[0] || val > mcp3564_calib_scale[2])
+			return -EINVAL;
+
+		if (adc->calib_scale == val)
+			return ret;
+
+		mutex_lock(&adc->lock);
+		ret = mcp3564_write_24bits(adc, MCP3564_GAINCAL_REG, val);
+		if (!ret)
+			adc->calib_scale = val;
+		mutex_unlock(&adc->lock);
+		return ret;
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		if (val < 0)
+			return -EINVAL;
+
+		tmp = find_closest(val, mcp3564_oversampling_avail,
+				   ARRAY_SIZE(mcp3564_oversampling_avail));
+
+		if (adc->oversampling == tmp)
+			return ret;
+
+		mutex_lock(&adc->lock);
+		ret = mcp3564_update_8bits(adc, MCP3564_CONFIG1_REG,
+					   MCP3564_CONFIG1_OVERSPL_RATIO_MASK,
+					   FIELD_PREP(MCP3564_CONFIG1_OVERSPL_RATIO_MASK,
+						      adc->oversampling));
+		if (!ret)
+			adc->oversampling = tmp;
+		mutex_unlock(&adc->lock);
+		return ret;
+	case IIO_CHAN_INFO_SCALE:
+		for (hwgain = 0; hwgain < MCP3564_MAX_PGA; hwgain++)
+			if (val == adc->scale_tbls[hwgain][0] &&
+			    val2 == adc->scale_tbls[hwgain][1])
+				break;
+
+		if (hwgain == MCP3564_MAX_PGA)
+			return -EINVAL;
+
+		if (hwgain == adc->hwgain)
+			return ret;
+
+		mutex_lock(&adc->lock);
+		ret = mcp3564_update_8bits(adc, MCP3564_CONFIG2_REG,
+					   MCP3564_CONFIG2_HARDWARE_GAIN_MASK,
+					   FIELD_PREP(MCP3564_CONFIG2_HARDWARE_GAIN_MASK, hwgain));
+		if (!ret)
+			adc->hwgain = hwgain;
+
+		mutex_unlock(&adc->lock);
+		return ret;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mcp3564_read_label(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan, char *label)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+
+	return sprintf(label, "%s\n", adc->labels[chan->scan_index]);
+}
+
+static int mcp3564_parse_fw_children(struct iio_dev *indio_dev)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	struct device *dev = &adc->spi->dev;
+	struct iio_chan_spec *channels;
+	struct fwnode_handle *child;
+	struct iio_chan_spec chanspec = mcp3564_channel_template;
+	struct iio_chan_spec temp_chanspec = mcp3564_temp_channel_template;
+	struct iio_chan_spec burnout_chanspec = mcp3564_burnout_channel_template;
+	int chan_idx = 0;
+	unsigned int num_ch;
+	u32 inputs[2];
+	const char *node_name;
+	const char *label;
+	int ret;
+
+	num_ch = device_get_child_node_count(dev);
+	if (num_ch == 0)
+		return dev_err_probe(&indio_dev->dev, -ENODEV,
+				     "FW has no channels defined\n");
+
+	/* Reserve space for burnout and temperature channel */
+	num_ch += 2;
+
+	if (num_ch > adc->chip_info->num_channels)
+		return dev_err_probe(dev, -EINVAL, "Too many channels %d > %d\n",
+				     num_ch, adc->chip_info->num_channels);
+
+	channels = devm_kcalloc(dev, num_ch, sizeof(*channels), GFP_KERNEL);
+	if (!channels)
+		return dev_err_probe(dev, -ENOMEM, "Can't allocate memory\n");
+
+	device_for_each_child_node(dev, child) {
+		node_name = fwnode_get_name(child);
+
+		if (fwnode_property_present(child, "diff-channels")) {
+			ret = fwnode_property_read_u32_array(child,
+							     "diff-channels",
+							     inputs,
+							     ARRAY_SIZE(inputs));
+			chanspec.differential = 1;
+		} else {
+			ret = fwnode_property_read_u32(child, "reg", &inputs[0]);
+
+			chanspec.differential = 0;
+			inputs[1] = MCP3564_AGND;
+		}
+		if (ret) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		if (inputs[0] > MCP3564_INTERNAL_VCM ||
+		    inputs[1] > MCP3564_INTERNAL_VCM) {
+			fwnode_handle_put(child);
+			return dev_err_probe(&indio_dev->dev, -EINVAL,
+					     "Channel index > %d, for %s\n",
+					     MCP3564_INTERNAL_VCM + 1,
+					     node_name);
+		}
+
+		chanspec.address = (inputs[0] << 4) | inputs[1];
+		chanspec.channel = inputs[0];
+		chanspec.channel2 = inputs[1];
+		chanspec.scan_index = chan_idx;
+
+		if (fwnode_property_present(child, "label")) {
+			fwnode_property_read_string(child, "label", &label);
+			adc->labels[chan_idx] = label;
+		}
+
+		channels[chan_idx] = chanspec;
+		chan_idx++;
+	}
+
+	/* Add burnout current channel */
+	burnout_chanspec.scan_index = chan_idx;
+	channels[chan_idx] = burnout_chanspec;
+	adc->labels[chan_idx] = mcp3564_channel_labels[0];
+	chanspec.scan_index = chan_idx;
+	chan_idx++;
+
+	/* Add temperature channel */
+	temp_chanspec.scan_index = chan_idx;
+	channels[chan_idx] = temp_chanspec;
+	adc->labels[chan_idx] = mcp3564_channel_labels[1];
+	chan_idx++;
+
+	indio_dev->num_channels = chan_idx;
+	indio_dev->channels = channels;
+
+	return 0;
+}
+
+static void mcp3564_disable_reg(void *reg)
+{
+	regulator_disable(reg);
+}
+
+static void mcp3564_fill_scale_tbls(struct mcp3564_state *adc)
+{
+	unsigned int pow = adc->chip_info->resolution - 1;
+	int ref;
+	unsigned int i;
+	int tmp0;
+	u64 tmp1;
+
+	for (i = 0; i < MCP3564_MAX_PGA; i++) {
+		ref = adc->vref_mv;
+		tmp1 = ((u64)ref * NANO) >> pow;
+		div_u64_rem(tmp1, NANO, &tmp0);
+
+		tmp1 = tmp1 * mcp3564_hwgain_frac[(2 * i) + 1];
+		tmp0 = (int)div_u64(tmp1, mcp3564_hwgain_frac[2 * i]);
+
+		adc->scale_tbls[i][1] = tmp0;
+	}
+}
+
+static int mcp3564_config(struct iio_dev *indio_dev)
+{
+	struct mcp3564_state *adc = iio_priv(indio_dev);
+	struct device *dev = &adc->spi->dev;
+	const struct spi_device_id *dev_id;
+	u8 tmp_reg;
+	u16 tmp_u16;
+	enum mcp3564_ids ids;
+	int ret = 0;
+	unsigned int tmp = 0x01;
+	bool err = false;
+
+	/*
+	 * The address is set on a per-device basis by fuses in the factory,
+	 * configured on request. If not requested, the fuses are set for 0x1.
+	 * The device address is part of the device markings to avoid
+	 * potential confusion. This address is coded on two bits, so four possible
+	 * addresses are available when multiple devices are present on the same
+	 * SPI bus with only one Chip Select line for all devices.
+	 */
+	device_property_read_u32(dev, "microchip,hw-device-address", &tmp);
+
+	if (tmp > 3) {
+		dev_err_probe(dev, tmp,
+			      "invalid device address. Must be in range 0-3.\n");
+		return -EINVAL;
+	}
+
+	adc->dev_addr = FIELD_GET(MCP3564_HW_ADDR_MASK, tmp);
+
+	dev_dbg(dev, "use HW device address %i\n", adc->dev_addr);
+
+	ret = mcp3564_read_8bits(adc, MCP3564_RESERVED_C_REG, &tmp_reg);
+	if (ret < 0)
+		return ret;
+
+	switch (tmp_reg) {
+	case MCP3564_C_REG_DEFAULT:
+		adc->have_vref = false;
+		break;
+	case MCP3564R_C_REG_DEFAULT:
+		adc->have_vref = true;
+		break;
+	default:
+		dev_info(dev, "Unknown chip found: %d\n", tmp_reg);
+		err = true;
+	}
+
+	if (!err) {
+		ret = mcp3564_read_16bits(adc, MCP3564_RESERVED_E_REG, &tmp_u16);
+		if (ret < 0)
+			return ret;
+
+		switch (tmp_u16 & MCP3564_HW_ID_MASK) {
+		case MCP3461_HW_ID:
+			if (adc->have_vref)
+				ids = mcp3461r;
+			else
+				ids = mcp3461;
+			break;
+		case MCP3462_HW_ID:
+			if (adc->have_vref)
+				ids = mcp3462r;
+			else
+				ids = mcp3462;
+			break;
+		case MCP3464_HW_ID:
+			if (adc->have_vref)
+				ids = mcp3464r;
+			else
+				ids = mcp3464;
+			break;
+		case MCP3561_HW_ID:
+			if (adc->have_vref)
+				ids = mcp3561r;
+			else
+				ids = mcp3561;
+			break;
+		case MCP3562_HW_ID:
+			if (adc->have_vref)
+				ids = mcp3562r;
+			else
+				ids = mcp3562;
+			break;
+		case MCP3564_HW_ID:
+			if (adc->have_vref)
+				ids = mcp3564r;
+			else
+				ids = mcp3564;
+			break;
+		default:
+			dev_info(dev, "Unknown chip found: %d\n", tmp_u16);
+			err = true;
+		}
+	}
+
+	if (err) {
+		/*
+		 * If failed to identify the hardware based on internal registers,
+		 * try using fallback compatible in device tree to deal with some newer part number.
+		 */
+		adc->chip_info = spi_get_device_match_data(adc->spi);
+		if (!adc->chip_info) {
+			dev_id = spi_get_device_id(adc->spi);
+			adc->chip_info = (const struct mcp3564_chip_info *)dev_id->driver_data;
+		}
+
+		adc->have_vref = adc->chip_info->have_vref;
+	} else {
+		adc->chip_info = &mcp3564_chip_infos_tbl[ids];
+	}
+
+	dev_dbg(dev, "Found %s chip\n", adc->chip_info->name);
+
+	adc->vref = devm_regulator_get_optional(dev, "vref");
+	if (IS_ERR(adc->vref)) {
+		if (PTR_ERR(adc->vref) != -ENODEV)
+			return dev_err_probe(dev, PTR_ERR(adc->vref),
+					     "failed to get regulator\n");
+
+		/* Check if chip has internal vref */
+		if (!adc->have_vref)
+			return dev_err_probe(dev, PTR_ERR(adc->vref),
+					     "Unknown Vref\n");
+		adc->vref = NULL;
+		dev_dbg(dev, "%s: Using internal Vref\n", __func__);
+	} else {
+		ret = regulator_enable(adc->vref);
+		if (ret)
+			return ret;
+
+		ret = devm_add_action_or_reset(dev, mcp3564_disable_reg,
+					       adc->vref);
+		if (ret)
+			return ret;
+
+		dev_dbg(dev, "%s: Using External Vref\n", __func__);
+
+		ret = regulator_get_voltage(adc->vref);
+		if (ret < 0)
+			return dev_err_probe(dev, ret,
+					     "Failed to read vref regulator\n");
+
+		adc->vref_mv = ret / MILLI;
+	}
+
+	ret = mcp3564_parse_fw_children(indio_dev);
+	if (ret)
+		return ret;
+
+	/*
+	 * Command sequence that ensures a recovery with the desired settings
+	 * in any cases of loss-of-power scenario (Full Chip Reset):
+	 *  - Write LOCK register to 0xA5
+	 *  - Write IRQ register to 0x03
+	 *  - Send "Device Full Reset" fast command
+	 *  - Wait 1ms for "Full Reset" to complete
+	 */
+	ret = mcp3564_write_8bits(adc, MCP3564_LOCK_REG, MCP3564_LOCK_WRITE_ACCESS_PASSWORD);
+	if (ret)
+		return ret;
+
+	ret = mcp3564_write_8bits(adc, MCP3564_IRQ_REG, 0x03);
+	if (ret)
+		return ret;
+
+	ret = mcp3564_fast_cmd(adc, MCP3564_FASTCMD_RESET);
+	if (ret)
+		return ret;
+
+	/*
+	 * After Full reset wait some time to be able to fully reset the part and place
+	 * it back in a default configuration.
+	 * From datasheet: POR (Power On Reset Time) is ~1us
+	 * 1ms should be enough.
+	 */
+	mdelay(1);
+
+	/* set a gain of 1x for GAINCAL */
+	ret = mcp3564_write_24bits(adc, MCP3564_GAINCAL_REG, MCP3564_DEFAULT_GAINCAL);
+	if (ret)
+		return ret;
+
+	adc->calib_scale = MCP3564_DEFAULT_GAINCAL;
+
+	ret = mcp3564_write_24bits(adc, MCP3564_OFFSETCAL_REG, MCP3564_DEFAULT_OFFSETCAL);
+	if (ret)
+		return ret;
+
+	ret = mcp3564_write_24bits(adc, MCP3564_TIMER_REG, MCP3564_TIMER_DEFAULT_VALUE);
+	if (ret)
+		return ret;
+
+	ret = mcp3564_write_24bits(adc, MCP3564_SCAN_REG,
+				   MCP3564_SCAN_DELAY_TIME_SET(MCP3564_NO_DELAY) |
+				   MCP3564_SCAN_CH_SEL_SET(MCP3564_SCAN_DEFAULT_VALUE));
+	if (ret)
+		return ret;
+
+	ret = mcp3564_write_8bits(adc, MCP3564_MUX_REG, MCP3564_MUX_SET(MCP3564_CH0, MCP3564_CH1));
+	if (ret)
+		return ret;
+
+	ret = mcp3564_write_8bits(adc, MCP3564_IRQ_REG,
+				  FIELD_PREP(MCP3464_EN_FASTCMD_MASK, 1) |
+				  FIELD_PREP(MCP3464_EN_STP_MASK, 1));
+	if (ret)
+		return ret;
+
+	tmp_reg = FIELD_PREP(MCP3464_CONFIG3_CONV_MODE_MASK,
+			     MCP3464_CONFIG3_CONV_MODE_ONE_SHOT_STANDBY);
+	tmp_reg |= FIELD_PREP(MCP3464_CONFIG3_DATA_FORMAT_MASK,
+			      MCP3464_CONFIG3_DATA_FMT_32B_SGN_EXT);
+	tmp_reg |= MCP3464_CONFIG3_EN_OFFCAL_MASK;
+	tmp_reg |= MCP3464_CONFIG3_EN_GAINCAL_MASK;
+
+	ret = mcp3564_write_8bits(adc, MCP3564_CONFIG3_REG, tmp_reg);
+	if (ret)
+		return ret;
+
+	tmp_reg = FIELD_PREP(MCP3564_CONFIG2_BOOST_CURRENT_MASK, MCP3564_BOOST_CURRENT_x1_00);
+	tmp_reg |= FIELD_PREP(MCP3564_CONFIG2_HARDWARE_GAIN_MASK, 0x01);
+	tmp_reg |= FIELD_PREP(MCP3564_CONFIG2_AZ_MUX_MASK, 1);
+
+	ret = mcp3564_write_8bits(adc, MCP3564_CONFIG2_REG, tmp_reg);
+	if (ret)
+		return ret;
+
+	adc->hwgain = 0x01;
+	adc->auto_zeroing_mux = true;
+	adc->auto_zeroing_ref = false;
+	adc->current_boost_mode = MCP3564_BOOST_CURRENT_x1_00;
+
+	tmp_reg = FIELD_PREP(MCP3564_CONFIG1_OVERSPL_RATIO_MASK, MCP3564_OVERSAMPLING_RATIO_98304);
+
+	ret = mcp3564_write_8bits(adc, MCP3564_CONFIG1_REG, tmp_reg);
+	if (ret)
+		return ret;
+
+	adc->oversampling = MCP3564_OVERSAMPLING_RATIO_98304;
+
+	tmp_reg = FIELD_PREP(MCP3564_CONFIG0_ADC_MODE_MASK, MCP3564_ADC_MODE_STANDBY);
+	tmp_reg |= FIELD_PREP(MCP3564_CONFIG0_CS_SEL_MASK, MCP3564_CONFIG0_CS_SEL_0_0_uA);
+	tmp_reg |= FIELD_PREP(MCP3564_CONFIG0_CLK_SEL_MASK, MCP3564_CONFIG0_USE_INT_CLK);
+	tmp_reg |= MCP3456_CONFIG0_BIT6_DEFAULT;
+
+	if (!adc->vref) {
+		tmp_reg |= FIELD_PREP(MCP3456_CONFIG0_VREF_MASK, 1);
+		adc->vref_mv = MCP3564R_INT_VREF_MV;
+	}
+
+	ret = mcp3564_write_8bits(adc, MCP3564_CONFIG0_REG, tmp_reg);
+
+	adc->burnout_mode = MCP3564_CONFIG0_CS_SEL_0_0_uA;
+
+	return ret;
+}
+
+static IIO_DEVICE_ATTR(auto_zeroing_ref_enable, 0644,
+		       mcp3564_auto_zeroing_ref_show,
+		       mcp3564_auto_zeroing_ref_store, 0);
+
+static IIO_DEVICE_ATTR(auto_zeroing_mux_enable, 0644,
+		       mcp3564_auto_zeroing_mux_show,
+		       mcp3564_auto_zeroing_mux_store, 0);
+
+static struct attribute *mcp3564_attributes[] = {
+	&iio_dev_attr_auto_zeroing_mux_enable.dev_attr.attr,
+	NULL
+};
+
+static struct attribute *mcp3564r_attributes[] = {
+	&iio_dev_attr_auto_zeroing_mux_enable.dev_attr.attr,
+	&iio_dev_attr_auto_zeroing_ref_enable.dev_attr.attr,
+	NULL
+};
+
+static struct attribute_group mcp3564_attribute_group = {
+	.attrs = mcp3564_attributes,
+};
+
+static struct attribute_group mcp3564r_attribute_group = {
+	.attrs = mcp3564r_attributes,
+};
+
+static const struct iio_info mcp3564_info = {
+	.read_raw = mcp3564_read_raw,
+	.read_avail = mcp3564_read_avail,
+	.write_raw = mcp3564_write_raw,
+	.write_raw_get_fmt = mcp3564_write_raw_get_fmt,
+	.read_label = mcp3564_read_label,
+	.attrs = &mcp3564_attribute_group,
+};
+
+static const struct iio_info mcp3564r_info = {
+	.read_raw = mcp3564_read_raw,
+	.read_avail = mcp3564_read_avail,
+	.write_raw = mcp3564_write_raw,
+	.write_raw_get_fmt = mcp3564_write_raw_get_fmt,
+	.read_label = mcp3564_read_label,
+	.attrs = &mcp3564r_attribute_group,
+};
+
+static int mcp3564_probe(struct spi_device *spi)
+{
+	int ret;
+	struct iio_dev *indio_dev;
+	struct mcp3564_state *adc;
+
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*adc));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	adc = iio_priv(indio_dev);
+	adc->spi = spi;
+
+	dev_dbg(&spi->dev, "%s: probe(spi = 0x%p)\n", __func__, spi);
+
+	/*
+	 * Do any chip specific initialization, e.g:
+	 * read/write some registers
+	 * enable/disable certain channels
+	 * change the sampling rate to the requested value
+	 */
+	ret = mcp3564_config(indio_dev);
+	if (ret)
+		return dev_err_probe(&spi->dev, ret,
+				     "Can't configure MCP356X device\n");
+
+	dev_dbg(&spi->dev, "%s: Vref (mV): %d\n", __func__, adc->vref_mv);
+
+	mcp3564_fill_scale_tbls(adc);
+
+	indio_dev->name = adc->chip_info->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	if (!adc->vref)
+		indio_dev->info = &mcp3564r_info;
+	else
+		indio_dev->info = &mcp3564_info;
+
+	mutex_init(&adc->lock);
+
+	ret = devm_iio_device_register(&spi->dev, indio_dev);
+	if (ret)
+		return dev_err_probe(&spi->dev, ret,
+				     "Can't register IIO device\n");
+
+	return 0;
+}
+
+static const struct of_device_id mcp3564_dt_ids[] = {
+	{ .compatible = "microchip,mcp3461", .data = &mcp3564_chip_infos_tbl[mcp3461] },
+	{ .compatible = "microchip,mcp3462", .data = &mcp3564_chip_infos_tbl[mcp3462] },
+	{ .compatible = "microchip,mcp3464", .data = &mcp3564_chip_infos_tbl[mcp3464] },
+	{ .compatible = "microchip,mcp3561", .data = &mcp3564_chip_infos_tbl[mcp3561] },
+	{ .compatible = "microchip,mcp3562", .data = &mcp3564_chip_infos_tbl[mcp3562] },
+	{ .compatible = "microchip,mcp3564", .data = &mcp3564_chip_infos_tbl[mcp3564] },
+	{ .compatible = "microchip,mcp3461r", .data = &mcp3564_chip_infos_tbl[mcp3461r] },
+	{ .compatible = "microchip,mcp3462r", .data = &mcp3564_chip_infos_tbl[mcp3462r] },
+	{ .compatible = "microchip,mcp3464r", .data = &mcp3564_chip_infos_tbl[mcp3464r] },
+	{ .compatible = "microchip,mcp3561r", .data = &mcp3564_chip_infos_tbl[mcp3561r] },
+	{ .compatible = "microchip,mcp3562r", .data = &mcp3564_chip_infos_tbl[mcp3562r] },
+	{ .compatible = "microchip,mcp3564r", .data = &mcp3564_chip_infos_tbl[mcp3564r] },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, mcp3564_dt_ids);
+
+static const struct spi_device_id mcp3564_id[] = {
+	{ "mcp3461", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3461] },
+	{ "mcp3462", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3462] },
+	{ "mcp3464", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3464] },
+	{ "mcp3561", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3561] },
+	{ "mcp3562", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3562] },
+	{ "mcp3564", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3564] },
+	{ "mcp3461r", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3461r] },
+	{ "mcp3462r", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3462r] },
+	{ "mcp3464r", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3464r] },
+	{ "mcp3561r", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3561r] },
+	{ "mcp3562r", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3562r] },
+	{ "mcp3564r", (kernel_ulong_t)&mcp3564_chip_infos_tbl[mcp3564r] },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, mcp3564_id);
+
+static struct spi_driver mcp3564_driver = {
+	.driver = {
+		.name = "mcp3564",
+		.of_match_table = mcp3564_dt_ids,
+	},
+	.probe = mcp3564_probe,
+	.id_table = mcp3564_id,
+};
+
+module_spi_driver(mcp3564_driver);
+
+MODULE_AUTHOR("Marius Cristea <marius.cristea@microchip.com>");
+MODULE_DESCRIPTION("Microchip MCP346x/MCP346xR and MCP356x/MCP356xR ADCs");
+MODULE_LICENSE("GPL v2");