Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 589 insertions, 0 deletions

diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
new file mode 100644
index 0000000000..4ed81f94f7
--- /dev/null
+++ b/drivers/mmc/host/dw_mmc.h
@@ -0,0 +1,589 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Synopsys DesignWare Multimedia Card Interface driver
+ *  (Based on NXP driver for lpc 31xx)
+ *
+ * Copyright (C) 2009 NXP Semiconductors
+ * Copyright (C) 2009, 2010 Imagination Technologies Ltd.
+ */
+
+#ifndef _DW_MMC_H_
+#define _DW_MMC_H_
+
+#include <linux/scatterlist.h>
+#include <linux/mmc/core.h>
+#include <linux/dmaengine.h>
+#include <linux/reset.h>
+#include <linux/fault-inject.h>
+#include <linux/hrtimer.h>
+#include <linux/interrupt.h>
+
+enum dw_mci_state {
+	STATE_IDLE = 0,
+	STATE_SENDING_CMD,
+	STATE_SENDING_DATA,
+	STATE_DATA_BUSY,
+	STATE_SENDING_STOP,
+	STATE_DATA_ERROR,
+	STATE_SENDING_CMD11,
+	STATE_WAITING_CMD11_DONE,
+};
+
+enum {
+	EVENT_CMD_COMPLETE = 0,
+	EVENT_XFER_COMPLETE,
+	EVENT_DATA_COMPLETE,
+	EVENT_DATA_ERROR,
+};
+
+enum dw_mci_cookie {
+	COOKIE_UNMAPPED,
+	COOKIE_PRE_MAPPED,	/* mapped by pre_req() of dwmmc */
+	COOKIE_MAPPED,		/* mapped by prepare_data() of dwmmc */
+};
+
+struct mmc_data;
+
+enum {
+	TRANS_MODE_PIO = 0,
+	TRANS_MODE_IDMAC,
+	TRANS_MODE_EDMAC
+};
+
+struct dw_mci_dma_slave {
+	struct dma_chan *ch;
+	enum dma_transfer_direction direction;
+};
+
+/**
+ * struct dw_mci - MMC controller state shared between all slots
+ * @lock: Spinlock protecting the queue and associated data.
+ * @irq_lock: Spinlock protecting the INTMASK setting.
+ * @regs: Pointer to MMIO registers.
+ * @fifo_reg: Pointer to MMIO registers for data FIFO
+ * @sg: Scatterlist entry currently being processed by PIO code, if any.
+ * @sg_miter: PIO mapping scatterlist iterator.
+ * @mrq: The request currently being processed on @slot,
+ *	or NULL if the controller is idle.
+ * @cmd: The command currently being sent to the card, or NULL.
+ * @data: The data currently being transferred, or NULL if no data
+ *	transfer is in progress.
+ * @stop_abort: The command currently prepared for stoping transfer.
+ * @prev_blksz: The former transfer blksz record.
+ * @timing: Record of current ios timing.
+ * @use_dma: Which DMA channel is in use for the current transfer, zero
+ *	denotes PIO mode.
+ * @using_dma: Whether DMA is in use for the current transfer.
+ * @dma_64bit_address: Whether DMA supports 64-bit address mode or not.
+ * @sg_dma: Bus address of DMA buffer.
+ * @sg_cpu: Virtual address of DMA buffer.
+ * @dma_ops: Pointer to platform-specific DMA callbacks.
+ * @cmd_status: Snapshot of SR taken upon completion of the current
+ * @ring_size: Buffer size for idma descriptors.
+ *	command. Only valid when EVENT_CMD_COMPLETE is pending.
+ * @dms: structure of slave-dma private data.
+ * @phy_regs: physical address of controller's register map
+ * @data_status: Snapshot of SR taken upon completion of the current
+ *	data transfer. Only valid when EVENT_DATA_COMPLETE or
+ *	EVENT_DATA_ERROR is pending.
+ * @stop_cmdr: Value to be loaded into CMDR when the stop command is
+ *	to be sent.
+ * @dir_status: Direction of current transfer.
+ * @tasklet: Tasklet running the request state machine.
+ * @pending_events: Bitmask of events flagged by the interrupt handler
+ *	to be processed by the tasklet.
+ * @completed_events: Bitmask of events which the state machine has
+ *	processed.
+ * @state: Tasklet state.
+ * @queue: List of slots waiting for access to the controller.
+ * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
+ *	rate and timeout calculations.
+ * @current_speed: Configured rate of the controller.
+ * @minimum_speed: Stored minimum rate of the controller.
+ * @fifoth_val: The value of FIFOTH register.
+ * @verid: Denote Version ID.
+ * @dev: Device associated with the MMC controller.
+ * @pdata: Platform data associated with the MMC controller.
+ * @drv_data: Driver specific data for identified variant of the controller
+ * @priv: Implementation defined private data.
+ * @biu_clk: Pointer to bus interface unit clock instance.
+ * @ciu_clk: Pointer to card interface unit clock instance.
+ * @slot: Slots sharing this MMC controller.
+ * @fifo_depth: depth of FIFO.
+ * @data_addr_override: override fifo reg offset with this value.
+ * @wm_aligned: force fifo watermark equal with data length in PIO mode.
+ *	Set as true if alignment is needed.
+ * @data_shift: log2 of FIFO item size.
+ * @part_buf_start: Start index in part_buf.
+ * @part_buf_count: Bytes of partial data in part_buf.
+ * @part_buf: Simple buffer for partial fifo reads/writes.
+ * @push_data: Pointer to FIFO push function.
+ * @pull_data: Pointer to FIFO pull function.
+ * @quirks: Set of quirks that apply to specific versions of the IP.
+ * @vqmmc_enabled: Status of vqmmc, should be true or false.
+ * @irq_flags: The flags to be passed to request_irq.
+ * @irq: The irq value to be passed to request_irq.
+ * @sdio_id0: Number of slot0 in the SDIO interrupt registers.
+ * @cmd11_timer: Timer for SD3.0 voltage switch over scheme.
+ * @cto_timer: Timer for broken command transfer over scheme.
+ * @dto_timer: Timer for broken data transfer over scheme.
+ *
+ * Locking
+ * =======
+ *
+ * @lock is a softirq-safe spinlock protecting @queue as well as
+ * @slot, @mrq and @state. These must always be updated
+ * at the same time while holding @lock.
+ * The @mrq field of struct dw_mci_slot is also protected by @lock,
+ * and must always be written at the same time as the slot is added to
+ * @queue.
+ *
+ * @irq_lock is an irq-safe spinlock protecting the INTMASK register
+ * to allow the interrupt handler to modify it directly.  Held for only long
+ * enough to read-modify-write INTMASK and no other locks are grabbed when
+ * holding this one.
+ *
+ * @pending_events and @completed_events are accessed using atomic bit
+ * operations, so they don't need any locking.
+ *
+ * None of the fields touched by the interrupt handler need any
+ * locking. However, ordering is important: Before EVENT_DATA_ERROR or
+ * EVENT_DATA_COMPLETE is set in @pending_events, all data-related
+ * interrupts must be disabled and @data_status updated with a
+ * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the
+ * CMDRDY interrupt must be disabled and @cmd_status updated with a
+ * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the
+ * bytes_xfered field of @data must be written. This is ensured by
+ * using barriers.
+ */
+struct dw_mci {
+	spinlock_t		lock;
+	spinlock_t		irq_lock;
+	void __iomem		*regs;
+	void __iomem		*fifo_reg;
+	u32			data_addr_override;
+	bool			wm_aligned;
+
+	struct scatterlist	*sg;
+	struct sg_mapping_iter	sg_miter;
+
+	struct mmc_request	*mrq;
+	struct mmc_command	*cmd;
+	struct mmc_data		*data;
+	struct mmc_command	stop_abort;
+	unsigned int		prev_blksz;
+	unsigned char		timing;
+
+	/* DMA interface members*/
+	int			use_dma;
+	int			using_dma;
+	int			dma_64bit_address;
+
+	dma_addr_t		sg_dma;
+	void			*sg_cpu;
+	const struct dw_mci_dma_ops	*dma_ops;
+	/* For idmac */
+	unsigned int		ring_size;
+
+	/* For edmac */
+	struct dw_mci_dma_slave *dms;
+	/* Registers's physical base address */
+	resource_size_t		phy_regs;
+
+	u32			cmd_status;
+	u32			data_status;
+	u32			stop_cmdr;
+	u32			dir_status;
+	struct tasklet_struct	tasklet;
+	unsigned long		pending_events;
+	unsigned long		completed_events;
+	enum dw_mci_state	state;
+	struct list_head	queue;
+
+	u32			bus_hz;
+	u32			current_speed;
+	u32			minimum_speed;
+	u32			fifoth_val;
+	u16			verid;
+	struct device		*dev;
+	struct dw_mci_board	*pdata;
+	const struct dw_mci_drv_data	*drv_data;
+	void			*priv;
+	struct clk		*biu_clk;
+	struct clk		*ciu_clk;
+	struct dw_mci_slot	*slot;
+
+	/* FIFO push and pull */
+	int			fifo_depth;
+	int			data_shift;
+	u8			part_buf_start;
+	u8			part_buf_count;
+	union {
+		u16		part_buf16;
+		u32		part_buf32;
+		u64		part_buf;
+	};
+	void (*push_data)(struct dw_mci *host, void *buf, int cnt);
+	void (*pull_data)(struct dw_mci *host, void *buf, int cnt);
+
+	u32			quirks;
+	bool			vqmmc_enabled;
+	unsigned long		irq_flags; /* IRQ flags */
+	int			irq;
+
+	int			sdio_id0;
+
+	struct timer_list       cmd11_timer;
+	struct timer_list       cto_timer;
+	struct timer_list       dto_timer;
+
+#ifdef CONFIG_FAULT_INJECTION
+	struct fault_attr	fail_data_crc;
+	struct hrtimer		fault_timer;
+#endif
+};
+
+/* DMA ops for Internal/External DMAC interface */
+struct dw_mci_dma_ops {
+	/* DMA Ops */
+	int (*init)(struct dw_mci *host);
+	int (*start)(struct dw_mci *host, unsigned int sg_len);
+	void (*complete)(void *host);
+	void (*stop)(struct dw_mci *host);
+	void (*cleanup)(struct dw_mci *host);
+	void (*exit)(struct dw_mci *host);
+};
+
+struct dma_pdata;
+
+/* Board platform data */
+struct dw_mci_board {
+	unsigned int bus_hz; /* Clock speed at the cclk_in pad */
+
+	u32 caps;	/* Capabilities */
+	u32 caps2;	/* More capabilities */
+	u32 pm_caps;	/* PM capabilities */
+	/*
+	 * Override fifo depth. If 0, autodetect it from the FIFOTH register,
+	 * but note that this may not be reliable after a bootloader has used
+	 * it.
+	 */
+	unsigned int fifo_depth;
+
+	/* delay in mS before detecting cards after interrupt */
+	u32 detect_delay_ms;
+
+	struct reset_control *rstc;
+	struct dw_mci_dma_ops *dma_ops;
+	struct dma_pdata *data;
+};
+
+/* Support for longer data read timeout */
+#define DW_MMC_QUIRK_EXTENDED_TMOUT            BIT(0)
+
+#define DW_MMC_240A		0x240a
+#define DW_MMC_280A		0x280a
+
+#define SDMMC_CTRL		0x000
+#define SDMMC_PWREN		0x004
+#define SDMMC_CLKDIV		0x008
+#define SDMMC_CLKSRC		0x00c
+#define SDMMC_CLKENA		0x010
+#define SDMMC_TMOUT		0x014
+#define SDMMC_CTYPE		0x018
+#define SDMMC_BLKSIZ		0x01c
+#define SDMMC_BYTCNT		0x020
+#define SDMMC_INTMASK		0x024
+#define SDMMC_CMDARG		0x028
+#define SDMMC_CMD		0x02c
+#define SDMMC_RESP0		0x030
+#define SDMMC_RESP1		0x034
+#define SDMMC_RESP2		0x038
+#define SDMMC_RESP3		0x03c
+#define SDMMC_MINTSTS		0x040
+#define SDMMC_RINTSTS		0x044
+#define SDMMC_STATUS		0x048
+#define SDMMC_FIFOTH		0x04c
+#define SDMMC_CDETECT		0x050
+#define SDMMC_WRTPRT		0x054
+#define SDMMC_GPIO		0x058
+#define SDMMC_TCBCNT		0x05c
+#define SDMMC_TBBCNT		0x060
+#define SDMMC_DEBNCE		0x064
+#define SDMMC_USRID		0x068
+#define SDMMC_VERID		0x06c
+#define SDMMC_HCON		0x070
+#define SDMMC_UHS_REG		0x074
+#define SDMMC_RST_N		0x078
+#define SDMMC_BMOD		0x080
+#define SDMMC_PLDMND		0x084
+#define SDMMC_DBADDR		0x088
+#define SDMMC_IDSTS		0x08c
+#define SDMMC_IDINTEN		0x090
+#define SDMMC_DSCADDR		0x094
+#define SDMMC_BUFADDR		0x098
+#define SDMMC_CDTHRCTL		0x100
+#define SDMMC_UHS_REG_EXT	0x108
+#define SDMMC_DDR_REG		0x10c
+#define SDMMC_ENABLE_SHIFT	0x110
+#define SDMMC_DATA(x)		(x)
+/*
+ * Registers to support idmac 64-bit address mode
+ */
+#define SDMMC_DBADDRL		0x088
+#define SDMMC_DBADDRU		0x08c
+#define SDMMC_IDSTS64		0x090
+#define SDMMC_IDINTEN64		0x094
+#define SDMMC_DSCADDRL		0x098
+#define SDMMC_DSCADDRU		0x09c
+#define SDMMC_BUFADDRL		0x0A0
+#define SDMMC_BUFADDRU		0x0A4
+
+/*
+ * Data offset is difference according to Version
+ * Lower than 2.40a : data register offest is 0x100
+ */
+#define DATA_OFFSET		0x100
+#define DATA_240A_OFFSET	0x200
+
+/* shift bit field */
+#define _SBF(f, v)		((v) << (f))
+
+/* Control register defines */
+#define SDMMC_CTRL_USE_IDMAC		BIT(25)
+#define SDMMC_CTRL_CEATA_INT_EN		BIT(11)
+#define SDMMC_CTRL_SEND_AS_CCSD		BIT(10)
+#define SDMMC_CTRL_SEND_CCSD		BIT(9)
+#define SDMMC_CTRL_ABRT_READ_DATA	BIT(8)
+#define SDMMC_CTRL_SEND_IRQ_RESP	BIT(7)
+#define SDMMC_CTRL_READ_WAIT		BIT(6)
+#define SDMMC_CTRL_DMA_ENABLE		BIT(5)
+#define SDMMC_CTRL_INT_ENABLE		BIT(4)
+#define SDMMC_CTRL_DMA_RESET		BIT(2)
+#define SDMMC_CTRL_FIFO_RESET		BIT(1)
+#define SDMMC_CTRL_RESET		BIT(0)
+/* Clock Enable register defines */
+#define SDMMC_CLKEN_LOW_PWR		BIT(16)
+#define SDMMC_CLKEN_ENABLE		BIT(0)
+/* time-out register defines */
+#define SDMMC_TMOUT_DATA(n)		_SBF(8, (n))
+#define SDMMC_TMOUT_DATA_MSK		0xFFFFFF00
+#define SDMMC_TMOUT_RESP(n)		((n) & 0xFF)
+#define SDMMC_TMOUT_RESP_MSK		0xFF
+/* card-type register defines */
+#define SDMMC_CTYPE_8BIT		BIT(16)
+#define SDMMC_CTYPE_4BIT		BIT(0)
+#define SDMMC_CTYPE_1BIT		0
+/* Interrupt status & mask register defines */
+#define SDMMC_INT_SDIO(n)		BIT(16 + (n))
+#define SDMMC_INT_EBE			BIT(15)
+#define SDMMC_INT_ACD			BIT(14)
+#define SDMMC_INT_SBE			BIT(13)
+#define SDMMC_INT_HLE			BIT(12)
+#define SDMMC_INT_FRUN			BIT(11)
+#define SDMMC_INT_HTO			BIT(10)
+#define SDMMC_INT_VOLT_SWITCH		BIT(10) /* overloads bit 10! */
+#define SDMMC_INT_DRTO			BIT(9)
+#define SDMMC_INT_RTO			BIT(8)
+#define SDMMC_INT_DCRC			BIT(7)
+#define SDMMC_INT_RCRC			BIT(6)
+#define SDMMC_INT_RXDR			BIT(5)
+#define SDMMC_INT_TXDR			BIT(4)
+#define SDMMC_INT_DATA_OVER		BIT(3)
+#define SDMMC_INT_CMD_DONE		BIT(2)
+#define SDMMC_INT_RESP_ERR		BIT(1)
+#define SDMMC_INT_CD			BIT(0)
+#define SDMMC_INT_ERROR			0xbfc2
+/* Command register defines */
+#define SDMMC_CMD_START			BIT(31)
+#define SDMMC_CMD_USE_HOLD_REG	BIT(29)
+#define SDMMC_CMD_VOLT_SWITCH		BIT(28)
+#define SDMMC_CMD_CCS_EXP		BIT(23)
+#define SDMMC_CMD_CEATA_RD		BIT(22)
+#define SDMMC_CMD_UPD_CLK		BIT(21)
+#define SDMMC_CMD_INIT			BIT(15)
+#define SDMMC_CMD_STOP			BIT(14)
+#define SDMMC_CMD_PRV_DAT_WAIT		BIT(13)
+#define SDMMC_CMD_SEND_STOP		BIT(12)
+#define SDMMC_CMD_STRM_MODE		BIT(11)
+#define SDMMC_CMD_DAT_WR		BIT(10)
+#define SDMMC_CMD_DAT_EXP		BIT(9)
+#define SDMMC_CMD_RESP_CRC		BIT(8)
+#define SDMMC_CMD_RESP_LONG		BIT(7)
+#define SDMMC_CMD_RESP_EXP		BIT(6)
+#define SDMMC_CMD_INDX(n)		((n) & 0x1F)
+/* Status register defines */
+#define SDMMC_GET_FCNT(x)		(((x)>>17) & 0x1FFF)
+#define SDMMC_STATUS_DMA_REQ		BIT(31)
+#define SDMMC_STATUS_BUSY		BIT(9)
+/* FIFOTH register defines */
+#define SDMMC_SET_FIFOTH(m, r, t)	(((m) & 0x7) << 28 | \
+					 ((r) & 0xFFF) << 16 | \
+					 ((t) & 0xFFF))
+/* HCON register defines */
+#define DMA_INTERFACE_IDMA		(0x0)
+#define DMA_INTERFACE_DWDMA		(0x1)
+#define DMA_INTERFACE_GDMA		(0x2)
+#define DMA_INTERFACE_NODMA		(0x3)
+#define SDMMC_GET_TRANS_MODE(x)		(((x)>>16) & 0x3)
+#define SDMMC_GET_SLOT_NUM(x)		((((x)>>1) & 0x1F) + 1)
+#define SDMMC_GET_HDATA_WIDTH(x)	(((x)>>7) & 0x7)
+#define SDMMC_GET_ADDR_CONFIG(x)	(((x)>>27) & 0x1)
+/* Internal DMAC interrupt defines */
+#define SDMMC_IDMAC_INT_AI		BIT(9)
+#define SDMMC_IDMAC_INT_NI		BIT(8)
+#define SDMMC_IDMAC_INT_CES		BIT(5)
+#define SDMMC_IDMAC_INT_DU		BIT(4)
+#define SDMMC_IDMAC_INT_FBE		BIT(2)
+#define SDMMC_IDMAC_INT_RI		BIT(1)
+#define SDMMC_IDMAC_INT_TI		BIT(0)
+/* Internal DMAC bus mode bits */
+#define SDMMC_IDMAC_ENABLE		BIT(7)
+#define SDMMC_IDMAC_FB			BIT(1)
+#define SDMMC_IDMAC_SWRESET		BIT(0)
+/* H/W reset */
+#define SDMMC_RST_HWACTIVE		0x1
+/* Version ID register define */
+#define SDMMC_GET_VERID(x)		((x) & 0xFFFF)
+/* Card read threshold */
+#define SDMMC_SET_THLD(v, x)		(((v) & 0xFFF) << 16 | (x))
+#define SDMMC_CARD_WR_THR_EN		BIT(2)
+#define SDMMC_CARD_RD_THR_EN		BIT(0)
+/* UHS-1 register defines */
+#define SDMMC_UHS_DDR			BIT(16)
+#define SDMMC_UHS_18V			BIT(0)
+/* DDR register defines */
+#define SDMMC_DDR_HS400			BIT(31)
+/* Enable shift register defines */
+#define SDMMC_ENABLE_PHASE		BIT(0)
+/* All ctrl reset bits */
+#define SDMMC_CTRL_ALL_RESET_FLAGS \
+	(SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET | SDMMC_CTRL_DMA_RESET)
+
+/* FIFO register access macros. These should not change the data endian-ness
+ * as they are written to memory to be dealt with by the upper layers
+ */
+#define mci_fifo_readw(__reg)	__raw_readw(__reg)
+#define mci_fifo_readl(__reg)	__raw_readl(__reg)
+#define mci_fifo_readq(__reg)	__raw_readq(__reg)
+
+#define mci_fifo_writew(__value, __reg)	__raw_writew(__reg, __value)
+#define mci_fifo_writel(__value, __reg)	__raw_writel(__reg, __value)
+#define mci_fifo_writeq(__value, __reg)	__raw_writeq(__reg, __value)
+
+/* Register access macros */
+#define mci_readl(dev, reg)			\
+	readl_relaxed((dev)->regs + SDMMC_##reg)
+#define mci_writel(dev, reg, value)			\
+	writel_relaxed((value), (dev)->regs + SDMMC_##reg)
+
+/* 16-bit FIFO access macros */
+#define mci_readw(dev, reg)			\
+	readw_relaxed((dev)->regs + SDMMC_##reg)
+#define mci_writew(dev, reg, value)			\
+	writew_relaxed((value), (dev)->regs + SDMMC_##reg)
+
+/* 64-bit FIFO access macros */
+#ifdef readq
+#define mci_readq(dev, reg)			\
+	readq_relaxed((dev)->regs + SDMMC_##reg)
+#define mci_writeq(dev, reg, value)			\
+	writeq_relaxed((value), (dev)->regs + SDMMC_##reg)
+#else
+/*
+ * Dummy readq implementation for architectures that don't define it.
+ *
+ * We would assume that none of these architectures would configure
+ * the IP block with a 64bit FIFO width, so this code will never be
+ * executed on those machines. Defining these macros here keeps the
+ * rest of the code free from ifdefs.
+ */
+#define mci_readq(dev, reg)			\
+	(*(volatile u64 __force *)((dev)->regs + SDMMC_##reg))
+#define mci_writeq(dev, reg, value)			\
+	(*(volatile u64 __force *)((dev)->regs + SDMMC_##reg) = (value))
+
+#define __raw_writeq(__value, __reg) \
+	(*(volatile u64 __force *)(__reg) = (__value))
+#define __raw_readq(__reg) (*(volatile u64 __force *)(__reg))
+#endif
+
+extern int dw_mci_probe(struct dw_mci *host);
+extern void dw_mci_remove(struct dw_mci *host);
+#ifdef CONFIG_PM
+extern int dw_mci_runtime_suspend(struct device *device);
+extern int dw_mci_runtime_resume(struct device *device);
+#endif
+
+/**
+ * struct dw_mci_slot - MMC slot state
+ * @mmc: The mmc_host representing this slot.
+ * @host: The MMC controller this slot is using.
+ * @ctype: Card type for this slot.
+ * @mrq: mmc_request currently being processed or waiting to be
+ *	processed, or NULL when the slot is idle.
+ * @queue_node: List node for placing this node in the @queue list of
+ *	&struct dw_mci.
+ * @clock: Clock rate configured by set_ios(). Protected by host->lock.
+ * @__clk_old: The last clock value that was requested from core.
+ *	Keeping track of this helps us to avoid spamming the console.
+ * @flags: Random state bits associated with the slot.
+ * @id: Number of this slot.
+ * @sdio_id: Number of this slot in the SDIO interrupt registers.
+ */
+struct dw_mci_slot {
+	struct mmc_host		*mmc;
+	struct dw_mci		*host;
+
+	u32			ctype;
+
+	struct mmc_request	*mrq;
+	struct list_head	queue_node;
+
+	unsigned int		clock;
+	unsigned int		__clk_old;
+
+	unsigned long		flags;
+#define DW_MMC_CARD_PRESENT	0
+#define DW_MMC_CARD_NEED_INIT	1
+#define DW_MMC_CARD_NO_LOW_PWR	2
+#define DW_MMC_CARD_NO_USE_HOLD 3
+#define DW_MMC_CARD_NEEDS_POLL	4
+	int			id;
+	int			sdio_id;
+};
+
+/**
+ * dw_mci driver data - dw-mshc implementation specific driver data.
+ * @caps: mmc subsystem specified capabilities of the controller(s).
+ * @num_caps: number of capabilities specified by @caps.
+ * @common_caps: mmc subsystem specified capabilities applicable to all of
+ *	the controllers
+ * @init: early implementation specific initialization.
+ * @set_ios: handle bus specific extensions.
+ * @parse_dt: parse implementation specific device tree properties.
+ * @execute_tuning: implementation specific tuning procedure.
+ * @set_data_timeout: implementation specific timeout.
+ * @get_drto_clks: implementation specific cycle count for data read timeout.
+ *
+ * Provide controller implementation specific extensions. The usage of this
+ * data structure is fully optional and usage of each member in this structure
+ * is optional as well.
+ */
+struct dw_mci_drv_data {
+	unsigned long	*caps;
+	u32		num_caps;
+	u32		common_caps;
+	int		(*init)(struct dw_mci *host);
+	void		(*set_ios)(struct dw_mci *host, struct mmc_ios *ios);
+	int		(*parse_dt)(struct dw_mci *host);
+	int		(*execute_tuning)(struct dw_mci_slot *slot, u32 opcode);
+	int		(*prepare_hs400_tuning)(struct dw_mci *host,
+						struct mmc_ios *ios);
+	int		(*switch_voltage)(struct mmc_host *mmc,
+					  struct mmc_ios *ios);
+	void		(*set_data_timeout)(struct dw_mci *host,
+					  unsigned int timeout_ns);
+	u32		(*get_drto_clks)(struct dw_mci *host);
+};
+#endif /* _DW_MMC_H_ */