diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-11 08:27:49 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-11 08:27:49 +0000 |
commit | ace9429bb58fd418f0c81d4c2835699bddf6bde6 (patch) | |
tree | b2d64bc10158fdd5497876388cd68142ca374ed3 /drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | |
parent | Initial commit. (diff) | |
download | linux-ace9429bb58fd418f0c81d4c2835699bddf6bde6.tar.xz linux-ace9429bb58fd418f0c81d4c2835699bddf6bde6.zip |
Adding upstream version 6.6.15.upstream/6.6.15
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'drivers/net/ethernet/intel/ixgbe/ixgbe_common.c')
-rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 4409 |
1 files changed, 4409 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c new file mode 100644 index 0000000000..878dd8dff5 --- /dev/null +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -0,0 +1,4409 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright(c) 1999 - 2018 Intel Corporation. */ + +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/sched.h> +#include <linux/netdevice.h> + +#include "ixgbe.h" +#include "ixgbe_common.h" +#include "ixgbe_phy.h" + +static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw); +static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw); +static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw); +static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw); +static void ixgbe_standby_eeprom(struct ixgbe_hw *hw); +static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, + u16 count); +static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count); +static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); +static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); +static void ixgbe_release_eeprom(struct ixgbe_hw *hw); + +static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); +static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg); +static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, + u16 offset); +static s32 ixgbe_disable_pcie_primary(struct ixgbe_hw *hw); + +/* Base table for registers values that change by MAC */ +const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = { + IXGBE_MVALS_INIT(8259X) +}; + +/** + * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow + * control + * @hw: pointer to hardware structure + * + * There are several phys that do not support autoneg flow control. This + * function check the device id to see if the associated phy supports + * autoneg flow control. + **/ +bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) +{ + bool supported = false; + ixgbe_link_speed speed; + bool link_up; + + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + /* flow control autoneg black list */ + switch (hw->device_id) { + case IXGBE_DEV_ID_X550EM_A_SFP: + case IXGBE_DEV_ID_X550EM_A_SFP_N: + supported = false; + break; + default: + hw->mac.ops.check_link(hw, &speed, &link_up, false); + /* if link is down, assume supported */ + if (link_up) + supported = speed == IXGBE_LINK_SPEED_1GB_FULL; + else + supported = true; + } + + break; + case ixgbe_media_type_backplane: + if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI) + supported = false; + else + supported = true; + break; + case ixgbe_media_type_copper: + /* only some copper devices support flow control autoneg */ + switch (hw->device_id) { + case IXGBE_DEV_ID_82599_T3_LOM: + case IXGBE_DEV_ID_X540T: + case IXGBE_DEV_ID_X540T1: + case IXGBE_DEV_ID_X550T: + case IXGBE_DEV_ID_X550T1: + case IXGBE_DEV_ID_X550EM_X_10G_T: + case IXGBE_DEV_ID_X550EM_A_10G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T_L: + supported = true; + break; + default: + break; + } + break; + default: + break; + } + + if (!supported) + hw_dbg(hw, "Device %x does not support flow control autoneg\n", + hw->device_id); + + return supported; +} + +/** + * ixgbe_setup_fc_generic - Set up flow control + * @hw: pointer to hardware structure + * + * Called at init time to set up flow control. + **/ +s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw) +{ + s32 ret_val = 0; + u32 reg = 0, reg_bp = 0; + u16 reg_cu = 0; + bool locked = false; + + /* + * Validate the requested mode. Strict IEEE mode does not allow + * ixgbe_fc_rx_pause because it will cause us to fail at UNH. + */ + if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { + hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); + return IXGBE_ERR_INVALID_LINK_SETTINGS; + } + + /* + * 10gig parts do not have a word in the EEPROM to determine the + * default flow control setting, so we explicitly set it to full. + */ + if (hw->fc.requested_mode == ixgbe_fc_default) + hw->fc.requested_mode = ixgbe_fc_full; + + /* + * Set up the 1G and 10G flow control advertisement registers so the + * HW will be able to do fc autoneg once the cable is plugged in. If + * we link at 10G, the 1G advertisement is harmless and vice versa. + */ + switch (hw->phy.media_type) { + case ixgbe_media_type_backplane: + /* some MAC's need RMW protection on AUTOC */ + ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, ®_bp); + if (ret_val) + return ret_val; + + fallthrough; /* only backplane uses autoc */ + case ixgbe_media_type_fiber: + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + + break; + case ixgbe_media_type_copper: + hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, ®_cu); + break; + default: + break; + } + + /* + * The possible values of fc.requested_mode are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + * other: Invalid. + */ + switch (hw->fc.requested_mode) { + case ixgbe_fc_none: + /* Flow control completely disabled by software override. */ + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled by software override. + */ + reg |= IXGBE_PCS1GANA_ASM_PAUSE; + reg &= ~IXGBE_PCS1GANA_SYM_PAUSE; + if (hw->phy.media_type == ixgbe_media_type_backplane) { + reg_bp |= IXGBE_AUTOC_ASM_PAUSE; + reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE; + } else if (hw->phy.media_type == ixgbe_media_type_copper) { + reg_cu |= IXGBE_TAF_ASM_PAUSE; + reg_cu &= ~IXGBE_TAF_SYM_PAUSE; + } + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE, as such we fall + * through to the fc_full statement. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + case ixgbe_fc_full: + /* Flow control (both Rx and Tx) is enabled by SW override. */ + reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE; + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp |= IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE; + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE; + break; + default: + hw_dbg(hw, "Flow control param set incorrectly\n"); + return IXGBE_ERR_CONFIG; + } + + if (hw->mac.type != ixgbe_mac_X540) { + /* + * Enable auto-negotiation between the MAC & PHY; + * the MAC will advertise clause 37 flow control. + */ + IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); + + /* Disable AN timeout */ + if (hw->fc.strict_ieee) + reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; + + IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); + hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg); + } + + /* + * AUTOC restart handles negotiation of 1G and 10G on backplane + * and copper. There is no need to set the PCS1GCTL register. + * + */ + if (hw->phy.media_type == ixgbe_media_type_backplane) { + /* Need the SW/FW semaphore around AUTOC writes if 82599 and + * LESM is on, likewise reset_pipeline requries the lock as + * it also writes AUTOC. + */ + ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked); + if (ret_val) + return ret_val; + + } else if ((hw->phy.media_type == ixgbe_media_type_copper) && + ixgbe_device_supports_autoneg_fc(hw)) { + hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, reg_cu); + } + + hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg); + return ret_val; +} + +/** + * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx + * @hw: pointer to hardware structure + * + * Starts the hardware by filling the bus info structure and media type, clears + * all on chip counters, initializes receive address registers, multicast + * table, VLAN filter table, calls routine to set up link and flow control + * settings, and leaves transmit and receive units disabled and uninitialized + **/ +s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) +{ + s32 ret_val; + u32 ctrl_ext; + u16 device_caps; + + /* Set the media type */ + hw->phy.media_type = hw->mac.ops.get_media_type(hw); + + /* Identify the PHY */ + hw->phy.ops.identify(hw); + + /* Clear the VLAN filter table */ + hw->mac.ops.clear_vfta(hw); + + /* Clear statistics registers */ + hw->mac.ops.clear_hw_cntrs(hw); + + /* Set No Snoop Disable */ + ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT); + ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS; + IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext); + IXGBE_WRITE_FLUSH(hw); + + /* Setup flow control if method for doing so */ + if (hw->mac.ops.setup_fc) { + ret_val = hw->mac.ops.setup_fc(hw); + if (ret_val) + return ret_val; + } + + /* Cashe bit indicating need for crosstalk fix */ + switch (hw->mac.type) { + case ixgbe_mac_82599EB: + case ixgbe_mac_X550EM_x: + case ixgbe_mac_x550em_a: + hw->mac.ops.get_device_caps(hw, &device_caps); + if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR) + hw->need_crosstalk_fix = false; + else + hw->need_crosstalk_fix = true; + break; + default: + hw->need_crosstalk_fix = false; + break; + } + + /* Clear adapter stopped flag */ + hw->adapter_stopped = false; + + return 0; +} + +/** + * ixgbe_start_hw_gen2 - Init sequence for common device family + * @hw: pointer to hw structure + * + * Performs the init sequence common to the second generation + * of 10 GbE devices. + * Devices in the second generation: + * 82599 + * X540 + **/ +s32 ixgbe_start_hw_gen2(struct ixgbe_hw *hw) +{ + u32 i; + + /* Clear the rate limiters */ + for (i = 0; i < hw->mac.max_tx_queues; i++) { + IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i); + IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0); + } + IXGBE_WRITE_FLUSH(hw); + + return 0; +} + +/** + * ixgbe_init_hw_generic - Generic hardware initialization + * @hw: pointer to hardware structure + * + * Initialize the hardware by resetting the hardware, filling the bus info + * structure and media type, clears all on chip counters, initializes receive + * address registers, multicast table, VLAN filter table, calls routine to set + * up link and flow control settings, and leaves transmit and receive units + * disabled and uninitialized + **/ +s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw) +{ + s32 status; + + /* Reset the hardware */ + status = hw->mac.ops.reset_hw(hw); + + if (status == 0) { + /* Start the HW */ + status = hw->mac.ops.start_hw(hw); + } + + /* Initialize the LED link active for LED blink support */ + if (hw->mac.ops.init_led_link_act) + hw->mac.ops.init_led_link_act(hw); + + return status; +} + +/** + * ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters + * @hw: pointer to hardware structure + * + * Clears all hardware statistics counters by reading them from the hardware + * Statistics counters are clear on read. + **/ +s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) +{ + u16 i = 0; + + IXGBE_READ_REG(hw, IXGBE_CRCERRS); + IXGBE_READ_REG(hw, IXGBE_ILLERRC); + IXGBE_READ_REG(hw, IXGBE_ERRBC); + IXGBE_READ_REG(hw, IXGBE_MSPDC); + for (i = 0; i < 8; i++) + IXGBE_READ_REG(hw, IXGBE_MPC(i)); + + IXGBE_READ_REG(hw, IXGBE_MLFC); + IXGBE_READ_REG(hw, IXGBE_MRFC); + IXGBE_READ_REG(hw, IXGBE_RLEC); + IXGBE_READ_REG(hw, IXGBE_LXONTXC); + IXGBE_READ_REG(hw, IXGBE_LXOFFTXC); + if (hw->mac.type >= ixgbe_mac_82599EB) { + IXGBE_READ_REG(hw, IXGBE_LXONRXCNT); + IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT); + } else { + IXGBE_READ_REG(hw, IXGBE_LXONRXC); + IXGBE_READ_REG(hw, IXGBE_LXOFFRXC); + } + + for (i = 0; i < 8; i++) { + IXGBE_READ_REG(hw, IXGBE_PXONTXC(i)); + IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i)); + if (hw->mac.type >= ixgbe_mac_82599EB) { + IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i)); + IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i)); + } else { + IXGBE_READ_REG(hw, IXGBE_PXONRXC(i)); + IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i)); + } + } + if (hw->mac.type >= ixgbe_mac_82599EB) + for (i = 0; i < 8; i++) + IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i)); + IXGBE_READ_REG(hw, IXGBE_PRC64); + IXGBE_READ_REG(hw, IXGBE_PRC127); + IXGBE_READ_REG(hw, IXGBE_PRC255); + IXGBE_READ_REG(hw, IXGBE_PRC511); + IXGBE_READ_REG(hw, IXGBE_PRC1023); + IXGBE_READ_REG(hw, IXGBE_PRC1522); + IXGBE_READ_REG(hw, IXGBE_GPRC); + IXGBE_READ_REG(hw, IXGBE_BPRC); + IXGBE_READ_REG(hw, IXGBE_MPRC); + IXGBE_READ_REG(hw, IXGBE_GPTC); + IXGBE_READ_REG(hw, IXGBE_GORCL); + IXGBE_READ_REG(hw, IXGBE_GORCH); + IXGBE_READ_REG(hw, IXGBE_GOTCL); + IXGBE_READ_REG(hw, IXGBE_GOTCH); + if (hw->mac.type == ixgbe_mac_82598EB) + for (i = 0; i < 8; i++) + IXGBE_READ_REG(hw, IXGBE_RNBC(i)); + IXGBE_READ_REG(hw, IXGBE_RUC); + IXGBE_READ_REG(hw, IXGBE_RFC); + IXGBE_READ_REG(hw, IXGBE_ROC); + IXGBE_READ_REG(hw, IXGBE_RJC); + IXGBE_READ_REG(hw, IXGBE_MNGPRC); + IXGBE_READ_REG(hw, IXGBE_MNGPDC); + IXGBE_READ_REG(hw, IXGBE_MNGPTC); + IXGBE_READ_REG(hw, IXGBE_TORL); + IXGBE_READ_REG(hw, IXGBE_TORH); + IXGBE_READ_REG(hw, IXGBE_TPR); + IXGBE_READ_REG(hw, IXGBE_TPT); + IXGBE_READ_REG(hw, IXGBE_PTC64); + IXGBE_READ_REG(hw, IXGBE_PTC127); + IXGBE_READ_REG(hw, IXGBE_PTC255); + IXGBE_READ_REG(hw, IXGBE_PTC511); + IXGBE_READ_REG(hw, IXGBE_PTC1023); + IXGBE_READ_REG(hw, IXGBE_PTC1522); + IXGBE_READ_REG(hw, IXGBE_MPTC); + IXGBE_READ_REG(hw, IXGBE_BPTC); + for (i = 0; i < 16; i++) { + IXGBE_READ_REG(hw, IXGBE_QPRC(i)); + IXGBE_READ_REG(hw, IXGBE_QPTC(i)); + if (hw->mac.type >= ixgbe_mac_82599EB) { + IXGBE_READ_REG(hw, IXGBE_QBRC_L(i)); + IXGBE_READ_REG(hw, IXGBE_QBRC_H(i)); + IXGBE_READ_REG(hw, IXGBE_QBTC_L(i)); + IXGBE_READ_REG(hw, IXGBE_QBTC_H(i)); + IXGBE_READ_REG(hw, IXGBE_QPRDC(i)); + } else { + IXGBE_READ_REG(hw, IXGBE_QBRC(i)); + IXGBE_READ_REG(hw, IXGBE_QBTC(i)); + } + } + + if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) { + if (hw->phy.id == 0) + hw->phy.ops.identify(hw); + hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i); + hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, MDIO_MMD_PCS, &i); + hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, MDIO_MMD_PCS, &i); + hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, MDIO_MMD_PCS, &i); + } + + return 0; +} + +/** + * ixgbe_read_pba_string_generic - Reads part number string from EEPROM + * @hw: pointer to hardware structure + * @pba_num: stores the part number string from the EEPROM + * @pba_num_size: part number string buffer length + * + * Reads the part number string from the EEPROM. + **/ +s32 ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num, + u32 pba_num_size) +{ + s32 ret_val; + u16 data; + u16 pba_ptr; + u16 offset; + u16 length; + + if (pba_num == NULL) { + hw_dbg(hw, "PBA string buffer was null\n"); + return IXGBE_ERR_INVALID_ARGUMENT; + } + + ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + + ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + + /* + * if data is not ptr guard the PBA must be in legacy format which + * means pba_ptr is actually our second data word for the PBA number + * and we can decode it into an ascii string + */ + if (data != IXGBE_PBANUM_PTR_GUARD) { + hw_dbg(hw, "NVM PBA number is not stored as string\n"); + + /* we will need 11 characters to store the PBA */ + if (pba_num_size < 11) { + hw_dbg(hw, "PBA string buffer too small\n"); + return IXGBE_ERR_NO_SPACE; + } + + /* extract hex string from data and pba_ptr */ + pba_num[0] = (data >> 12) & 0xF; + pba_num[1] = (data >> 8) & 0xF; + pba_num[2] = (data >> 4) & 0xF; + pba_num[3] = data & 0xF; + pba_num[4] = (pba_ptr >> 12) & 0xF; + pba_num[5] = (pba_ptr >> 8) & 0xF; + pba_num[6] = '-'; + pba_num[7] = 0; + pba_num[8] = (pba_ptr >> 4) & 0xF; + pba_num[9] = pba_ptr & 0xF; + + /* put a null character on the end of our string */ + pba_num[10] = '\0'; + + /* switch all the data but the '-' to hex char */ + for (offset = 0; offset < 10; offset++) { + if (pba_num[offset] < 0xA) + pba_num[offset] += '0'; + else if (pba_num[offset] < 0x10) + pba_num[offset] += 'A' - 0xA; + } + + return 0; + } + + ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + + if (length == 0xFFFF || length == 0) { + hw_dbg(hw, "NVM PBA number section invalid length\n"); + return IXGBE_ERR_PBA_SECTION; + } + + /* check if pba_num buffer is big enough */ + if (pba_num_size < (((u32)length * 2) - 1)) { + hw_dbg(hw, "PBA string buffer too small\n"); + return IXGBE_ERR_NO_SPACE; + } + + /* trim pba length from start of string */ + pba_ptr++; + length--; + + for (offset = 0; offset < length; offset++) { + ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + pba_num[offset * 2] = (u8)(data >> 8); + pba_num[(offset * 2) + 1] = (u8)(data & 0xFF); + } + pba_num[offset * 2] = '\0'; + + return 0; +} + +/** + * ixgbe_get_mac_addr_generic - Generic get MAC address + * @hw: pointer to hardware structure + * @mac_addr: Adapter MAC address + * + * Reads the adapter's MAC address from first Receive Address Register (RAR0) + * A reset of the adapter must be performed prior to calling this function + * in order for the MAC address to have been loaded from the EEPROM into RAR0 + **/ +s32 ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr) +{ + u32 rar_high; + u32 rar_low; + u16 i; + + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0)); + rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0)); + + for (i = 0; i < 4; i++) + mac_addr[i] = (u8)(rar_low >> (i*8)); + + for (i = 0; i < 2; i++) + mac_addr[i+4] = (u8)(rar_high >> (i*8)); + + return 0; +} + +enum ixgbe_bus_width ixgbe_convert_bus_width(u16 link_status) +{ + switch (link_status & IXGBE_PCI_LINK_WIDTH) { + case IXGBE_PCI_LINK_WIDTH_1: + return ixgbe_bus_width_pcie_x1; + case IXGBE_PCI_LINK_WIDTH_2: + return ixgbe_bus_width_pcie_x2; + case IXGBE_PCI_LINK_WIDTH_4: + return ixgbe_bus_width_pcie_x4; + case IXGBE_PCI_LINK_WIDTH_8: + return ixgbe_bus_width_pcie_x8; + default: + return ixgbe_bus_width_unknown; + } +} + +enum ixgbe_bus_speed ixgbe_convert_bus_speed(u16 link_status) +{ + switch (link_status & IXGBE_PCI_LINK_SPEED) { + case IXGBE_PCI_LINK_SPEED_2500: + return ixgbe_bus_speed_2500; + case IXGBE_PCI_LINK_SPEED_5000: + return ixgbe_bus_speed_5000; + case IXGBE_PCI_LINK_SPEED_8000: + return ixgbe_bus_speed_8000; + default: + return ixgbe_bus_speed_unknown; + } +} + +/** + * ixgbe_get_bus_info_generic - Generic set PCI bus info + * @hw: pointer to hardware structure + * + * Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure + **/ +s32 ixgbe_get_bus_info_generic(struct ixgbe_hw *hw) +{ + u16 link_status; + + hw->bus.type = ixgbe_bus_type_pci_express; + + /* Get the negotiated link width and speed from PCI config space */ + link_status = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_LINK_STATUS); + + hw->bus.width = ixgbe_convert_bus_width(link_status); + hw->bus.speed = ixgbe_convert_bus_speed(link_status); + + hw->mac.ops.set_lan_id(hw); + + return 0; +} + +/** + * ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices + * @hw: pointer to the HW structure + * + * Determines the LAN function id by reading memory-mapped registers + * and swaps the port value if requested. + **/ +void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw) +{ + struct ixgbe_bus_info *bus = &hw->bus; + u16 ee_ctrl_4; + u32 reg; + + reg = IXGBE_READ_REG(hw, IXGBE_STATUS); + bus->func = (reg & IXGBE_STATUS_LAN_ID) >> IXGBE_STATUS_LAN_ID_SHIFT; + bus->lan_id = bus->func; + + /* check for a port swap */ + reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw)); + if (reg & IXGBE_FACTPS_LFS) + bus->func ^= 0x1; + + /* Get MAC instance from EEPROM for configuring CS4227 */ + if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) { + hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4); + bus->instance_id = (ee_ctrl_4 & IXGBE_EE_CTRL_4_INST_ID) >> + IXGBE_EE_CTRL_4_INST_ID_SHIFT; + } +} + +/** + * ixgbe_stop_adapter_generic - Generic stop Tx/Rx units + * @hw: pointer to hardware structure + * + * Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts, + * disables transmit and receive units. The adapter_stopped flag is used by + * the shared code and drivers to determine if the adapter is in a stopped + * state and should not touch the hardware. + **/ +s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw) +{ + u32 reg_val; + u16 i; + + /* + * Set the adapter_stopped flag so other driver functions stop touching + * the hardware + */ + hw->adapter_stopped = true; + + /* Disable the receive unit */ + hw->mac.ops.disable_rx(hw); + + /* Clear interrupt mask to stop interrupts from being generated */ + IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK); + + /* Clear any pending interrupts, flush previous writes */ + IXGBE_READ_REG(hw, IXGBE_EICR); + + /* Disable the transmit unit. Each queue must be disabled. */ + for (i = 0; i < hw->mac.max_tx_queues; i++) + IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH); + + /* Disable the receive unit by stopping each queue */ + for (i = 0; i < hw->mac.max_rx_queues; i++) { + reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i)); + reg_val &= ~IXGBE_RXDCTL_ENABLE; + reg_val |= IXGBE_RXDCTL_SWFLSH; + IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val); + } + + /* flush all queues disables */ + IXGBE_WRITE_FLUSH(hw); + usleep_range(1000, 2000); + + /* + * Prevent the PCI-E bus from hanging by disabling PCI-E primary + * access and verify no pending requests + */ + return ixgbe_disable_pcie_primary(hw); +} + +/** + * ixgbe_init_led_link_act_generic - Store the LED index link/activity. + * @hw: pointer to hardware structure + * + * Store the index for the link active LED. This will be used to support + * blinking the LED. + **/ +s32 ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw) +{ + struct ixgbe_mac_info *mac = &hw->mac; + u32 led_reg, led_mode; + u16 i; + + led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + + /* Get LED link active from the LEDCTL register */ + for (i = 0; i < 4; i++) { + led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i); + + if ((led_mode & IXGBE_LED_MODE_MASK_BASE) == + IXGBE_LED_LINK_ACTIVE) { + mac->led_link_act = i; + return 0; + } + } + + /* If LEDCTL register does not have the LED link active set, then use + * known MAC defaults. + */ + switch (hw->mac.type) { + case ixgbe_mac_x550em_a: + mac->led_link_act = 0; + break; + case ixgbe_mac_X550EM_x: + mac->led_link_act = 1; + break; + default: + mac->led_link_act = 2; + } + + return 0; +} + +/** + * ixgbe_led_on_generic - Turns on the software controllable LEDs. + * @hw: pointer to hardware structure + * @index: led number to turn on + **/ +s32 ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index) +{ + u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + + if (index > 3) + return IXGBE_ERR_PARAM; + + /* To turn on the LED, set mode to ON. */ + led_reg &= ~IXGBE_LED_MODE_MASK(index); + led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index); + IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); + IXGBE_WRITE_FLUSH(hw); + + return 0; +} + +/** + * ixgbe_led_off_generic - Turns off the software controllable LEDs. + * @hw: pointer to hardware structure + * @index: led number to turn off + **/ +s32 ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index) +{ + u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + + if (index > 3) + return IXGBE_ERR_PARAM; + + /* To turn off the LED, set mode to OFF. */ + led_reg &= ~IXGBE_LED_MODE_MASK(index); + led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index); + IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); + IXGBE_WRITE_FLUSH(hw); + + return 0; +} + +/** + * ixgbe_init_eeprom_params_generic - Initialize EEPROM params + * @hw: pointer to hardware structure + * + * Initializes the EEPROM parameters ixgbe_eeprom_info within the + * ixgbe_hw struct in order to set up EEPROM access. + **/ +s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw) +{ + struct ixgbe_eeprom_info *eeprom = &hw->eeprom; + u32 eec; + u16 eeprom_size; + + if (eeprom->type == ixgbe_eeprom_uninitialized) { + eeprom->type = ixgbe_eeprom_none; + /* Set default semaphore delay to 10ms which is a well + * tested value */ + eeprom->semaphore_delay = 10; + /* Clear EEPROM page size, it will be initialized as needed */ + eeprom->word_page_size = 0; + + /* + * Check for EEPROM present first. + * If not present leave as none + */ + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + if (eec & IXGBE_EEC_PRES) { + eeprom->type = ixgbe_eeprom_spi; + + /* + * SPI EEPROM is assumed here. This code would need to + * change if a future EEPROM is not SPI. + */ + eeprom_size = (u16)((eec & IXGBE_EEC_SIZE) >> + IXGBE_EEC_SIZE_SHIFT); + eeprom->word_size = BIT(eeprom_size + + IXGBE_EEPROM_WORD_SIZE_SHIFT); + } + + if (eec & IXGBE_EEC_ADDR_SIZE) + eeprom->address_bits = 16; + else + eeprom->address_bits = 8; + hw_dbg(hw, "Eeprom params: type = %d, size = %d, address bits: %d\n", + eeprom->type, eeprom->word_size, eeprom->address_bits); + } + + return 0; +} + +/** + * ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to write + * @words: number of words + * @data: 16 bit word(s) to write to EEPROM + * + * Reads 16 bit word(s) from EEPROM through bit-bang method + **/ +s32 ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data) +{ + s32 status; + u16 i, count; + + hw->eeprom.ops.init_params(hw); + + if (words == 0) + return IXGBE_ERR_INVALID_ARGUMENT; + + if (offset + words > hw->eeprom.word_size) + return IXGBE_ERR_EEPROM; + + /* + * The EEPROM page size cannot be queried from the chip. We do lazy + * initialization. It is worth to do that when we write large buffer. + */ + if ((hw->eeprom.word_page_size == 0) && + (words > IXGBE_EEPROM_PAGE_SIZE_MAX)) + ixgbe_detect_eeprom_page_size_generic(hw, offset); + + /* + * We cannot hold synchronization semaphores for too long + * to avoid other entity starvation. However it is more efficient + * to read in bursts than synchronizing access for each word. + */ + for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) { + count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ? + IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i); + status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i, + count, &data[i]); + + if (status != 0) + break; + } + + return status; +} + +/** + * ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be written to + * @words: number of word(s) + * @data: 16 bit word(s) to be written to the EEPROM + * + * If ixgbe_eeprom_update_checksum is not called after this function, the + * EEPROM will most likely contain an invalid checksum. + **/ +static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data) +{ + s32 status; + u16 word; + u16 page_size; + u16 i; + u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI; + + /* Prepare the EEPROM for writing */ + status = ixgbe_acquire_eeprom(hw); + if (status) + return status; + + if (ixgbe_ready_eeprom(hw) != 0) { + ixgbe_release_eeprom(hw); + return IXGBE_ERR_EEPROM; + } + + for (i = 0; i < words; i++) { + ixgbe_standby_eeprom(hw); + + /* Send the WRITE ENABLE command (8 bit opcode) */ + ixgbe_shift_out_eeprom_bits(hw, + IXGBE_EEPROM_WREN_OPCODE_SPI, + IXGBE_EEPROM_OPCODE_BITS); + + ixgbe_standby_eeprom(hw); + + /* Some SPI eeproms use the 8th address bit embedded + * in the opcode + */ + if ((hw->eeprom.address_bits == 8) && + ((offset + i) >= 128)) + write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; + + /* Send the Write command (8-bit opcode + addr) */ + ixgbe_shift_out_eeprom_bits(hw, write_opcode, + IXGBE_EEPROM_OPCODE_BITS); + ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2), + hw->eeprom.address_bits); + + page_size = hw->eeprom.word_page_size; + + /* Send the data in burst via SPI */ + do { + word = data[i]; + word = (word >> 8) | (word << 8); + ixgbe_shift_out_eeprom_bits(hw, word, 16); + + if (page_size == 0) + break; + + /* do not wrap around page */ + if (((offset + i) & (page_size - 1)) == + (page_size - 1)) + break; + } while (++i < words); + + ixgbe_standby_eeprom(hw); + usleep_range(10000, 20000); + } + /* Done with writing - release the EEPROM */ + ixgbe_release_eeprom(hw); + + return 0; +} + +/** + * ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be written to + * @data: 16 bit word to be written to the EEPROM + * + * If ixgbe_eeprom_update_checksum is not called after this function, the + * EEPROM will most likely contain an invalid checksum. + **/ +s32 ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data) +{ + hw->eeprom.ops.init_params(hw); + + if (offset >= hw->eeprom.word_size) + return IXGBE_ERR_EEPROM; + + return ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data); +} + +/** + * ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be read + * @words: number of word(s) + * @data: read 16 bit words(s) from EEPROM + * + * Reads 16 bit word(s) from EEPROM through bit-bang method + **/ +s32 ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data) +{ + s32 status; + u16 i, count; + + hw->eeprom.ops.init_params(hw); + + if (words == 0) + return IXGBE_ERR_INVALID_ARGUMENT; + + if (offset + words > hw->eeprom.word_size) + return IXGBE_ERR_EEPROM; + + /* + * We cannot hold synchronization semaphores for too long + * to avoid other entity starvation. However it is more efficient + * to read in bursts than synchronizing access for each word. + */ + for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) { + count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ? + IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i); + + status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i, + count, &data[i]); + + if (status) + return status; + } + + return 0; +} + +/** + * ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be read + * @words: number of word(s) + * @data: read 16 bit word(s) from EEPROM + * + * Reads 16 bit word(s) from EEPROM through bit-bang method + **/ +static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data) +{ + s32 status; + u16 word_in; + u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI; + u16 i; + + /* Prepare the EEPROM for reading */ + status = ixgbe_acquire_eeprom(hw); + if (status) + return status; + + if (ixgbe_ready_eeprom(hw) != 0) { + ixgbe_release_eeprom(hw); + return IXGBE_ERR_EEPROM; + } + + for (i = 0; i < words; i++) { + ixgbe_standby_eeprom(hw); + /* Some SPI eeproms use the 8th address bit embedded + * in the opcode + */ + if ((hw->eeprom.address_bits == 8) && + ((offset + i) >= 128)) + read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; + + /* Send the READ command (opcode + addr) */ + ixgbe_shift_out_eeprom_bits(hw, read_opcode, + IXGBE_EEPROM_OPCODE_BITS); + ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2), + hw->eeprom.address_bits); + + /* Read the data. */ + word_in = ixgbe_shift_in_eeprom_bits(hw, 16); + data[i] = (word_in >> 8) | (word_in << 8); + } + + /* End this read operation */ + ixgbe_release_eeprom(hw); + + return 0; +} + +/** + * ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be read + * @data: read 16 bit value from EEPROM + * + * Reads 16 bit value from EEPROM through bit-bang method + **/ +s32 ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, + u16 *data) +{ + hw->eeprom.ops.init_params(hw); + + if (offset >= hw->eeprom.word_size) + return IXGBE_ERR_EEPROM; + + return ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data); +} + +/** + * ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD + * @hw: pointer to hardware structure + * @offset: offset of word in the EEPROM to read + * @words: number of word(s) + * @data: 16 bit word(s) from the EEPROM + * + * Reads a 16 bit word(s) from the EEPROM using the EERD register. + **/ +s32 ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data) +{ + u32 eerd; + s32 status; + u32 i; + + hw->eeprom.ops.init_params(hw); + + if (words == 0) + return IXGBE_ERR_INVALID_ARGUMENT; + + if (offset >= hw->eeprom.word_size) + return IXGBE_ERR_EEPROM; + + for (i = 0; i < words; i++) { + eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) | + IXGBE_EEPROM_RW_REG_START; + + IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd); + status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ); + + if (status == 0) { + data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >> + IXGBE_EEPROM_RW_REG_DATA); + } else { + hw_dbg(hw, "Eeprom read timed out\n"); + return status; + } + } + + return 0; +} + +/** + * ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size + * @hw: pointer to hardware structure + * @offset: offset within the EEPROM to be used as a scratch pad + * + * Discover EEPROM page size by writing marching data at given offset. + * This function is called only when we are writing a new large buffer + * at given offset so the data would be overwritten anyway. + **/ +static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, + u16 offset) +{ + u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX]; + s32 status; + u16 i; + + for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++) + data[i] = i; + + hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX; + status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset, + IXGBE_EEPROM_PAGE_SIZE_MAX, data); + hw->eeprom.word_page_size = 0; + if (status) + return status; + + status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data); + if (status) + return status; + + /* + * When writing in burst more than the actual page size + * EEPROM address wraps around current page. + */ + hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0]; + + hw_dbg(hw, "Detected EEPROM page size = %d words.\n", + hw->eeprom.word_page_size); + return 0; +} + +/** + * ixgbe_read_eerd_generic - Read EEPROM word using EERD + * @hw: pointer to hardware structure + * @offset: offset of word in the EEPROM to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM using the EERD register. + **/ +s32 ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data) +{ + return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data); +} + +/** + * ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR + * @hw: pointer to hardware structure + * @offset: offset of word in the EEPROM to write + * @words: number of words + * @data: word(s) write to the EEPROM + * + * Write a 16 bit word(s) to the EEPROM using the EEWR register. + **/ +s32 ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset, + u16 words, u16 *data) +{ + u32 eewr; + s32 status; + u16 i; + + hw->eeprom.ops.init_params(hw); + + if (words == 0) + return IXGBE_ERR_INVALID_ARGUMENT; + + if (offset >= hw->eeprom.word_size) + return IXGBE_ERR_EEPROM; + + for (i = 0; i < words; i++) { + eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) | + (data[i] << IXGBE_EEPROM_RW_REG_DATA) | + IXGBE_EEPROM_RW_REG_START; + + status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE); + if (status) { + hw_dbg(hw, "Eeprom write EEWR timed out\n"); + return status; + } + + IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr); + + status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE); + if (status) { + hw_dbg(hw, "Eeprom write EEWR timed out\n"); + return status; + } + } + + return 0; +} + +/** + * ixgbe_write_eewr_generic - Write EEPROM word using EEWR + * @hw: pointer to hardware structure + * @offset: offset of word in the EEPROM to write + * @data: word write to the EEPROM + * + * Write a 16 bit word to the EEPROM using the EEWR register. + **/ +s32 ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data) +{ + return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data); +} + +/** + * ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status + * @hw: pointer to hardware structure + * @ee_reg: EEPROM flag for polling + * + * Polls the status bit (bit 1) of the EERD or EEWR to determine when the + * read or write is done respectively. + **/ +static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg) +{ + u32 i; + u32 reg; + + for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) { + if (ee_reg == IXGBE_NVM_POLL_READ) + reg = IXGBE_READ_REG(hw, IXGBE_EERD); + else + reg = IXGBE_READ_REG(hw, IXGBE_EEWR); + + if (reg & IXGBE_EEPROM_RW_REG_DONE) { + return 0; + } + udelay(5); + } + return IXGBE_ERR_EEPROM; +} + +/** + * ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang + * @hw: pointer to hardware structure + * + * Prepares EEPROM for access using bit-bang method. This function should + * be called before issuing a command to the EEPROM. + **/ +static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) +{ + u32 eec; + u32 i; + + if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0) + return IXGBE_ERR_SWFW_SYNC; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + + /* Request EEPROM Access */ + eec |= IXGBE_EEC_REQ; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + + for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) { + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + if (eec & IXGBE_EEC_GNT) + break; + udelay(5); + } + + /* Release if grant not acquired */ + if (!(eec & IXGBE_EEC_GNT)) { + eec &= ~IXGBE_EEC_REQ; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + hw_dbg(hw, "Could not acquire EEPROM grant\n"); + + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); + return IXGBE_ERR_EEPROM; + } + + /* Setup EEPROM for Read/Write */ + /* Clear CS and SK */ + eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); + return 0; +} + +/** + * ixgbe_get_eeprom_semaphore - Get hardware semaphore + * @hw: pointer to hardware structure + * + * Sets the hardware semaphores so EEPROM access can occur for bit-bang method + **/ +static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) +{ + u32 timeout = 2000; + u32 i; + u32 swsm; + + /* Get SMBI software semaphore between device drivers first */ + for (i = 0; i < timeout; i++) { + /* + * If the SMBI bit is 0 when we read it, then the bit will be + * set and we have the semaphore + */ + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); + if (!(swsm & IXGBE_SWSM_SMBI)) + break; + usleep_range(50, 100); + } + + if (i == timeout) { + hw_dbg(hw, "Driver can't access the Eeprom - SMBI Semaphore not granted.\n"); + /* this release is particularly important because our attempts + * above to get the semaphore may have succeeded, and if there + * was a timeout, we should unconditionally clear the semaphore + * bits to free the driver to make progress + */ + ixgbe_release_eeprom_semaphore(hw); + + usleep_range(50, 100); + /* one last try + * If the SMBI bit is 0 when we read it, then the bit will be + * set and we have the semaphore + */ + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); + if (swsm & IXGBE_SWSM_SMBI) { + hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n"); + return IXGBE_ERR_EEPROM; + } + } + + /* Now get the semaphore between SW/FW through the SWESMBI bit */ + for (i = 0; i < timeout; i++) { + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); + + /* Set the SW EEPROM semaphore bit to request access */ + swsm |= IXGBE_SWSM_SWESMBI; + IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm); + + /* If we set the bit successfully then we got the + * semaphore. + */ + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); + if (swsm & IXGBE_SWSM_SWESMBI) + break; + + usleep_range(50, 100); + } + + /* Release semaphores and return error if SW EEPROM semaphore + * was not granted because we don't have access to the EEPROM + */ + if (i >= timeout) { + hw_dbg(hw, "SWESMBI Software EEPROM semaphore not granted.\n"); + ixgbe_release_eeprom_semaphore(hw); + return IXGBE_ERR_EEPROM; + } + + return 0; +} + +/** + * ixgbe_release_eeprom_semaphore - Release hardware semaphore + * @hw: pointer to hardware structure + * + * This function clears hardware semaphore bits. + **/ +static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw) +{ + u32 swsm; + + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); + + /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */ + swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI); + IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm); + IXGBE_WRITE_FLUSH(hw); +} + +/** + * ixgbe_ready_eeprom - Polls for EEPROM ready + * @hw: pointer to hardware structure + **/ +static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw) +{ + u16 i; + u8 spi_stat_reg; + + /* + * Read "Status Register" repeatedly until the LSB is cleared. The + * EEPROM will signal that the command has been completed by clearing + * bit 0 of the internal status register. If it's not cleared within + * 5 milliseconds, then error out. + */ + for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) { + ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI, + IXGBE_EEPROM_OPCODE_BITS); + spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8); + if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI)) + break; + + udelay(5); + ixgbe_standby_eeprom(hw); + } + + /* + * On some parts, SPI write time could vary from 0-20mSec on 3.3V + * devices (and only 0-5mSec on 5V devices) + */ + if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) { + hw_dbg(hw, "SPI EEPROM Status error\n"); + return IXGBE_ERR_EEPROM; + } + + return 0; +} + +/** + * ixgbe_standby_eeprom - Returns EEPROM to a "standby" state + * @hw: pointer to hardware structure + **/ +static void ixgbe_standby_eeprom(struct ixgbe_hw *hw) +{ + u32 eec; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + + /* Toggle CS to flush commands */ + eec |= IXGBE_EEC_CS; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); + eec &= ~IXGBE_EEC_CS; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); +} + +/** + * ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM. + * @hw: pointer to hardware structure + * @data: data to send to the EEPROM + * @count: number of bits to shift out + **/ +static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, + u16 count) +{ + u32 eec; + u32 mask; + u32 i; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + + /* + * Mask is used to shift "count" bits of "data" out to the EEPROM + * one bit at a time. Determine the starting bit based on count + */ + mask = BIT(count - 1); + + for (i = 0; i < count; i++) { + /* + * A "1" is shifted out to the EEPROM by setting bit "DI" to a + * "1", and then raising and then lowering the clock (the SK + * bit controls the clock input to the EEPROM). A "0" is + * shifted out to the EEPROM by setting "DI" to "0" and then + * raising and then lowering the clock. + */ + if (data & mask) + eec |= IXGBE_EEC_DI; + else + eec &= ~IXGBE_EEC_DI; + + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + IXGBE_WRITE_FLUSH(hw); + + udelay(1); + + ixgbe_raise_eeprom_clk(hw, &eec); + ixgbe_lower_eeprom_clk(hw, &eec); + + /* + * Shift mask to signify next bit of data to shift in to the + * EEPROM + */ + mask = mask >> 1; + } + + /* We leave the "DI" bit set to "0" when we leave this routine. */ + eec &= ~IXGBE_EEC_DI; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + IXGBE_WRITE_FLUSH(hw); +} + +/** + * ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM + * @hw: pointer to hardware structure + * @count: number of bits to shift + **/ +static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) +{ + u32 eec; + u32 i; + u16 data = 0; + + /* + * In order to read a register from the EEPROM, we need to shift + * 'count' bits in from the EEPROM. Bits are "shifted in" by raising + * the clock input to the EEPROM (setting the SK bit), and then reading + * the value of the "DO" bit. During this "shifting in" process the + * "DI" bit should always be clear. + */ + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + + eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI); + + for (i = 0; i < count; i++) { + data = data << 1; + ixgbe_raise_eeprom_clk(hw, &eec); + + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + + eec &= ~(IXGBE_EEC_DI); + if (eec & IXGBE_EEC_DO) + data |= 1; + + ixgbe_lower_eeprom_clk(hw, &eec); + } + + return data; +} + +/** + * ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input. + * @hw: pointer to hardware structure + * @eec: EEC register's current value + **/ +static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) +{ + /* + * Raise the clock input to the EEPROM + * (setting the SK bit), then delay + */ + *eec = *eec | IXGBE_EEC_SK; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); +} + +/** + * ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input. + * @hw: pointer to hardware structure + * @eec: EEC's current value + **/ +static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) +{ + /* + * Lower the clock input to the EEPROM (clearing the SK bit), then + * delay + */ + *eec = *eec & ~IXGBE_EEC_SK; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec); + IXGBE_WRITE_FLUSH(hw); + udelay(1); +} + +/** + * ixgbe_release_eeprom - Release EEPROM, release semaphores + * @hw: pointer to hardware structure + **/ +static void ixgbe_release_eeprom(struct ixgbe_hw *hw) +{ + u32 eec; + + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); + + eec |= IXGBE_EEC_CS; /* Pull CS high */ + eec &= ~IXGBE_EEC_SK; /* Lower SCK */ + + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + IXGBE_WRITE_FLUSH(hw); + + udelay(1); + + /* Stop requesting EEPROM access */ + eec &= ~IXGBE_EEC_REQ; + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); + + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); + + /* + * Delay before attempt to obtain semaphore again to allow FW + * access. semaphore_delay is in ms we need us for usleep_range + */ + usleep_range(hw->eeprom.semaphore_delay * 1000, + hw->eeprom.semaphore_delay * 2000); +} + +/** + * ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum + * @hw: pointer to hardware structure + **/ +s32 ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw) +{ + u16 i; + u16 j; + u16 checksum = 0; + u16 length = 0; + u16 pointer = 0; + u16 word = 0; + + /* Include 0x0-0x3F in the checksum */ + for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) { + if (hw->eeprom.ops.read(hw, i, &word)) { + hw_dbg(hw, "EEPROM read failed\n"); + break; + } + checksum += word; + } + + /* Include all data from pointers except for the fw pointer */ + for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) { + if (hw->eeprom.ops.read(hw, i, &pointer)) { + hw_dbg(hw, "EEPROM read failed\n"); + return IXGBE_ERR_EEPROM; + } + + /* If the pointer seems invalid */ + if (pointer == 0xFFFF || pointer == 0) + continue; + + if (hw->eeprom.ops.read(hw, pointer, &length)) { + hw_dbg(hw, "EEPROM read failed\n"); + return IXGBE_ERR_EEPROM; + } + + if (length == 0xFFFF || length == 0) + continue; + + for (j = pointer + 1; j <= pointer + length; j++) { + if (hw->eeprom.ops.read(hw, j, &word)) { + hw_dbg(hw, "EEPROM read failed\n"); + return IXGBE_ERR_EEPROM; + } + checksum += word; + } + } + + checksum = (u16)IXGBE_EEPROM_SUM - checksum; + + return (s32)checksum; +} + +/** + * ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum + * @hw: pointer to hardware structure + * @checksum_val: calculated checksum + * + * Performs checksum calculation and validates the EEPROM checksum. If the + * caller does not need checksum_val, the value can be NULL. + **/ +s32 ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw, + u16 *checksum_val) +{ + s32 status; + u16 checksum; + u16 read_checksum = 0; + + /* + * Read the first word from the EEPROM. If this times out or fails, do + * not continue or we could be in for a very long wait while every + * EEPROM read fails + */ + status = hw->eeprom.ops.read(hw, 0, &checksum); + if (status) { + hw_dbg(hw, "EEPROM read failed\n"); + return status; + } + + status = hw->eeprom.ops.calc_checksum(hw); + if (status < 0) + return status; + + checksum = (u16)(status & 0xffff); + + status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum); + if (status) { + hw_dbg(hw, "EEPROM read failed\n"); + return status; + } + + /* Verify read checksum from EEPROM is the same as + * calculated checksum + */ + if (read_checksum != checksum) + status = IXGBE_ERR_EEPROM_CHECKSUM; + + /* If the user cares, return the calculated checksum */ + if (checksum_val) + *checksum_val = checksum; + + return status; +} + +/** + * ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum + * @hw: pointer to hardware structure + **/ +s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw) +{ + s32 status; + u16 checksum; + + /* + * Read the first word from the EEPROM. If this times out or fails, do + * not continue or we could be in for a very long wait while every + * EEPROM read fails + */ + status = hw->eeprom.ops.read(hw, 0, &checksum); + if (status) { + hw_dbg(hw, "EEPROM read failed\n"); + return status; + } + + status = hw->eeprom.ops.calc_checksum(hw); + if (status < 0) + return status; + + checksum = (u16)(status & 0xffff); + + status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum); + + return status; +} + +/** + * ixgbe_set_rar_generic - Set Rx address register + * @hw: pointer to hardware structure + * @index: Receive address register to write + * @addr: Address to put into receive address register + * @vmdq: VMDq "set" or "pool" index + * @enable_addr: set flag that address is active + * + * Puts an ethernet address into a receive address register. + **/ +s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq, + u32 enable_addr) +{ + u32 rar_low, rar_high; + u32 rar_entries = hw->mac.num_rar_entries; + + /* Make sure we are using a valid rar index range */ + if (index >= rar_entries) { + hw_dbg(hw, "RAR index %d is out of range.\n", index); + return IXGBE_ERR_INVALID_ARGUMENT; + } + + /* setup VMDq pool selection before this RAR gets enabled */ + hw->mac.ops.set_vmdq(hw, index, vmdq); + + /* + * HW expects these in little endian so we reverse the byte + * order from network order (big endian) to little endian + */ + rar_low = ((u32)addr[0] | + ((u32)addr[1] << 8) | + ((u32)addr[2] << 16) | + ((u32)addr[3] << 24)); + /* + * Some parts put the VMDq setting in the extra RAH bits, + * so save everything except the lower 16 bits that hold part + * of the address and the address valid bit. + */ + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); + rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); + rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8)); + + if (enable_addr != 0) + rar_high |= IXGBE_RAH_AV; + + /* Record lower 32 bits of MAC address and then make + * sure that write is flushed to hardware before writing + * the upper 16 bits and setting the valid bit. + */ + IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); + IXGBE_WRITE_FLUSH(hw); + IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); + + return 0; +} + +/** + * ixgbe_clear_rar_generic - Remove Rx address register + * @hw: pointer to hardware structure + * @index: Receive address register to write + * + * Clears an ethernet address from a receive address register. + **/ +s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index) +{ + u32 rar_high; + u32 rar_entries = hw->mac.num_rar_entries; + + /* Make sure we are using a valid rar index range */ + if (index >= rar_entries) { + hw_dbg(hw, "RAR index %d is out of range.\n", index); + return IXGBE_ERR_INVALID_ARGUMENT; + } + + /* + * Some parts put the VMDq setting in the extra RAH bits, + * so save everything except the lower 16 bits that hold part + * of the address and the address valid bit. + */ + rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); + rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); + + /* Clear the address valid bit and upper 16 bits of the address + * before clearing the lower bits. This way we aren't updating + * a live filter. + */ + IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); + IXGBE_WRITE_FLUSH(hw); + IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); + + /* clear VMDq pool/queue selection for this RAR */ + hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL); + + return 0; +} + +/** + * ixgbe_init_rx_addrs_generic - Initializes receive address filters. + * @hw: pointer to hardware structure + * + * Places the MAC address in receive address register 0 and clears the rest + * of the receive address registers. Clears the multicast table. Assumes + * the receiver is in reset when the routine is called. + **/ +s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw) +{ + u32 i; + u32 rar_entries = hw->mac.num_rar_entries; + + /* + * If the current mac address is valid, assume it is a software override + * to the permanent address. + * Otherwise, use the permanent address from the eeprom. + */ + if (!is_valid_ether_addr(hw->mac.addr)) { + /* Get the MAC address from the RAR0 for later reference */ + hw->mac.ops.get_mac_addr(hw, hw->mac.addr); + + hw_dbg(hw, " Keeping Current RAR0 Addr =%pM\n", hw->mac.addr); + } else { + /* Setup the receive address. */ + hw_dbg(hw, "Overriding MAC Address in RAR[0]\n"); + hw_dbg(hw, " New MAC Addr =%pM\n", hw->mac.addr); + + hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV); + } + + /* clear VMDq pool/queue selection for RAR 0 */ + hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL); + + hw->addr_ctrl.overflow_promisc = 0; + + hw->addr_ctrl.rar_used_count = 1; + + /* Zero out the other receive addresses. */ + hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1); + for (i = 1; i < rar_entries; i++) { + IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); + IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); + } + + /* Clear the MTA */ + hw->addr_ctrl.mta_in_use = 0; + IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); + + hw_dbg(hw, " Clearing MTA\n"); + for (i = 0; i < hw->mac.mcft_size; i++) + IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); + + if (hw->mac.ops.init_uta_tables) + hw->mac.ops.init_uta_tables(hw); + + return 0; +} + +/** + * ixgbe_mta_vector - Determines bit-vector in multicast table to set + * @hw: pointer to hardware structure + * @mc_addr: the multicast address + * + * Extracts the 12 bits, from a multicast address, to determine which + * bit-vector to set in the multicast table. The hardware uses 12 bits, from + * incoming rx multicast addresses, to determine the bit-vector to check in + * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set + * by the MO field of the MCSTCTRL. The MO field is set during initialization + * to mc_filter_type. + **/ +static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr) +{ + u32 vector = 0; + + switch (hw->mac.mc_filter_type) { + case 0: /* use bits [47:36] of the address */ + vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); + break; + case 1: /* use bits [46:35] of the address */ + vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); + break; + case 2: /* use bits [45:34] of the address */ + vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); + break; + case 3: /* use bits [43:32] of the address */ + vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); + break; + default: /* Invalid mc_filter_type */ + hw_dbg(hw, "MC filter type param set incorrectly\n"); + break; + } + + /* vector can only be 12-bits or boundary will be exceeded */ + vector &= 0xFFF; + return vector; +} + +/** + * ixgbe_set_mta - Set bit-vector in multicast table + * @hw: pointer to hardware structure + * @mc_addr: Multicast address + * + * Sets the bit-vector in the multicast table. + **/ +static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr) +{ + u32 vector; + u32 vector_bit; + u32 vector_reg; + + hw->addr_ctrl.mta_in_use++; + + vector = ixgbe_mta_vector(hw, mc_addr); + hw_dbg(hw, " bit-vector = 0x%03X\n", vector); + + /* + * The MTA is a register array of 128 32-bit registers. It is treated + * like an array of 4096 bits. We want to set bit + * BitArray[vector_value]. So we figure out what register the bit is + * in, read it, OR in the new bit, then write back the new value. The + * register is determined by the upper 7 bits of the vector value and + * the bit within that register are determined by the lower 5 bits of + * the value. + */ + vector_reg = (vector >> 5) & 0x7F; + vector_bit = vector & 0x1F; + hw->mac.mta_shadow[vector_reg] |= BIT(vector_bit); +} + +/** + * ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses + * @hw: pointer to hardware structure + * @netdev: pointer to net device structure + * + * The given list replaces any existing list. Clears the MC addrs from receive + * address registers and the multicast table. Uses unused receive address + * registers for the first multicast addresses, and hashes the rest into the + * multicast table. + **/ +s32 ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw, + struct net_device *netdev) +{ + struct netdev_hw_addr *ha; + u32 i; + + /* + * Set the new number of MC addresses that we are being requested to + * use. + */ + hw->addr_ctrl.num_mc_addrs = netdev_mc_count(netdev); + hw->addr_ctrl.mta_in_use = 0; + + /* Clear mta_shadow */ + hw_dbg(hw, " Clearing MTA\n"); + memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); + + /* Update mta shadow */ + netdev_for_each_mc_addr(ha, netdev) { + hw_dbg(hw, " Adding the multicast addresses:\n"); + ixgbe_set_mta(hw, ha->addr); + } + + /* Enable mta */ + for (i = 0; i < hw->mac.mcft_size; i++) + IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i, + hw->mac.mta_shadow[i]); + + if (hw->addr_ctrl.mta_in_use > 0) + IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, + IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type); + + hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n"); + return 0; +} + +/** + * ixgbe_enable_mc_generic - Enable multicast address in RAR + * @hw: pointer to hardware structure + * + * Enables multicast address in RAR and the use of the multicast hash table. + **/ +s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw) +{ + struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; + + if (a->mta_in_use > 0) + IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE | + hw->mac.mc_filter_type); + + return 0; +} + +/** + * ixgbe_disable_mc_generic - Disable multicast address in RAR + * @hw: pointer to hardware structure + * + * Disables multicast address in RAR and the use of the multicast hash table. + **/ +s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) +{ + struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; + + if (a->mta_in_use > 0) + IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); + + return 0; +} + +/** + * ixgbe_fc_enable_generic - Enable flow control + * @hw: pointer to hardware structure + * + * Enable flow control according to the current settings. + **/ +s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) +{ + u32 mflcn_reg, fccfg_reg; + u32 reg; + u32 fcrtl, fcrth; + int i; + + /* Validate the water mark configuration. */ + if (!hw->fc.pause_time) + return IXGBE_ERR_INVALID_LINK_SETTINGS; + + /* Low water mark of zero causes XOFF floods */ + for (i = 0; i < MAX_TRAFFIC_CLASS; i++) { + if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && + hw->fc.high_water[i]) { + if (!hw->fc.low_water[i] || + hw->fc.low_water[i] >= hw->fc.high_water[i]) { + hw_dbg(hw, "Invalid water mark configuration\n"); + return IXGBE_ERR_INVALID_LINK_SETTINGS; + } + } + } + + /* Negotiate the fc mode to use */ + hw->mac.ops.fc_autoneg(hw); + + /* Disable any previous flow control settings */ + mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); + mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE); + + fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG); + fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY); + + /* + * The possible values of fc.current_mode are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + * other: Invalid. + */ + switch (hw->fc.current_mode) { + case ixgbe_fc_none: + /* + * Flow control is disabled by software override or autoneg. + * The code below will actually disable it in the HW. + */ + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + mflcn_reg |= IXGBE_MFLCN_RFCE; + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled by software override. + */ + fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; + break; + case ixgbe_fc_full: + /* Flow control (both Rx and Tx) is enabled by SW override. */ + mflcn_reg |= IXGBE_MFLCN_RFCE; + fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; + break; + default: + hw_dbg(hw, "Flow control param set incorrectly\n"); + return IXGBE_ERR_CONFIG; + } + + /* Set 802.3x based flow control settings. */ + mflcn_reg |= IXGBE_MFLCN_DPF; + IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); + IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); + + /* Set up and enable Rx high/low water mark thresholds, enable XON. */ + for (i = 0; i < MAX_TRAFFIC_CLASS; i++) { + if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && + hw->fc.high_water[i]) { + fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE; + IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl); + fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN; + } else { + IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0); + /* + * In order to prevent Tx hangs when the internal Tx + * switch is enabled we must set the high water mark + * to the Rx packet buffer size - 24KB. This allows + * the Tx switch to function even under heavy Rx + * workloads. + */ + fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576; + } + + IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth); + } + + /* Configure pause time (2 TCs per register) */ + reg = hw->fc.pause_time * 0x00010001U; + for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++) + IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg); + + IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2); + + return 0; +} + +/** + * ixgbe_negotiate_fc - Negotiate flow control + * @hw: pointer to hardware structure + * @adv_reg: flow control advertised settings + * @lp_reg: link partner's flow control settings + * @adv_sym: symmetric pause bit in advertisement + * @adv_asm: asymmetric pause bit in advertisement + * @lp_sym: symmetric pause bit in link partner advertisement + * @lp_asm: asymmetric pause bit in link partner advertisement + * + * Find the intersection between advertised settings and link partner's + * advertised settings + **/ +s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, + u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) +{ + if ((!(adv_reg)) || (!(lp_reg))) + return IXGBE_ERR_FC_NOT_NEGOTIATED; + + if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) { + /* + * Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == ixgbe_fc_full) { + hw->fc.current_mode = ixgbe_fc_full; + hw_dbg(hw, "Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control=RX PAUSE frames only\n"); + } + } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) && + (lp_reg & lp_sym) && (lp_reg & lp_asm)) { + hw->fc.current_mode = ixgbe_fc_tx_pause; + hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); + } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) && + !(lp_reg & lp_sym) && (lp_reg & lp_asm)) { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); + } else { + hw->fc.current_mode = ixgbe_fc_none; + hw_dbg(hw, "Flow Control = NONE.\n"); + } + return 0; +} + +/** + * ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber + * @hw: pointer to hardware structure + * + * Enable flow control according on 1 gig fiber. + **/ +static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw) +{ + u32 pcs_anadv_reg, pcs_lpab_reg, linkstat; + s32 ret_val; + + /* + * On multispeed fiber at 1g, bail out if + * - link is up but AN did not complete, or if + * - link is up and AN completed but timed out + */ + + linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); + if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) || + (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) + return IXGBE_ERR_FC_NOT_NEGOTIATED; + + pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); + + ret_val = ixgbe_negotiate_fc(hw, pcs_anadv_reg, + pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE, + IXGBE_PCS1GANA_ASM_PAUSE, + IXGBE_PCS1GANA_SYM_PAUSE, + IXGBE_PCS1GANA_ASM_PAUSE); + + return ret_val; +} + +/** + * ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37 + * @hw: pointer to hardware structure + * + * Enable flow control according to IEEE clause 37. + **/ +static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw) +{ + u32 links2, anlp1_reg, autoc_reg, links; + s32 ret_val; + + /* + * On backplane, bail out if + * - backplane autoneg was not completed, or if + * - we are 82599 and link partner is not AN enabled + */ + links = IXGBE_READ_REG(hw, IXGBE_LINKS); + if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) + return IXGBE_ERR_FC_NOT_NEGOTIATED; + + if (hw->mac.type == ixgbe_mac_82599EB) { + links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2); + if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) + return IXGBE_ERR_FC_NOT_NEGOTIATED; + } + /* + * Read the 10g AN autoc and LP ability registers and resolve + * local flow control settings accordingly + */ + autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1); + + ret_val = ixgbe_negotiate_fc(hw, autoc_reg, + anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE, + IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE); + + return ret_val; +} + +/** + * ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37 + * @hw: pointer to hardware structure + * + * Enable flow control according to IEEE clause 37. + **/ +static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw) +{ + u16 technology_ability_reg = 0; + u16 lp_technology_ability_reg = 0; + + hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, + &technology_ability_reg); + hw->phy.ops.read_reg(hw, MDIO_AN_LPA, + MDIO_MMD_AN, + &lp_technology_ability_reg); + + return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg, + (u32)lp_technology_ability_reg, + IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE, + IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE); +} + +/** + * ixgbe_fc_autoneg - Configure flow control + * @hw: pointer to hardware structure + * + * Compares our advertised flow control capabilities to those advertised by + * our link partner, and determines the proper flow control mode to use. + **/ +void ixgbe_fc_autoneg(struct ixgbe_hw *hw) +{ + s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; + ixgbe_link_speed speed; + bool link_up; + + /* + * AN should have completed when the cable was plugged in. + * Look for reasons to bail out. Bail out if: + * - FC autoneg is disabled, or if + * - link is not up. + * + * Since we're being called from an LSC, link is already known to be up. + * So use link_up_wait_to_complete=false. + */ + if (hw->fc.disable_fc_autoneg) + goto out; + + hw->mac.ops.check_link(hw, &speed, &link_up, false); + if (!link_up) + goto out; + + switch (hw->phy.media_type) { + /* Autoneg flow control on fiber adapters */ + case ixgbe_media_type_fiber: + if (speed == IXGBE_LINK_SPEED_1GB_FULL) + ret_val = ixgbe_fc_autoneg_fiber(hw); + break; + + /* Autoneg flow control on backplane adapters */ + case ixgbe_media_type_backplane: + ret_val = ixgbe_fc_autoneg_backplane(hw); + break; + + /* Autoneg flow control on copper adapters */ + case ixgbe_media_type_copper: + if (ixgbe_device_supports_autoneg_fc(hw)) + ret_val = ixgbe_fc_autoneg_copper(hw); + break; + + default: + break; + } + +out: + if (ret_val == 0) { + hw->fc.fc_was_autonegged = true; + } else { + hw->fc.fc_was_autonegged = false; + hw->fc.current_mode = hw->fc.requested_mode; + } +} + +/** + * ixgbe_pcie_timeout_poll - Return number of times to poll for completion + * @hw: pointer to hardware structure + * + * System-wide timeout range is encoded in PCIe Device Control2 register. + * + * Add 10% to specified maximum and return the number of times to poll for + * completion timeout, in units of 100 microsec. Never return less than + * 800 = 80 millisec. + **/ +static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw) +{ + s16 devctl2; + u32 pollcnt; + + devctl2 = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_CONTROL2); + devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK; + + switch (devctl2) { + case IXGBE_PCIDEVCTRL2_65_130ms: + pollcnt = 1300; /* 130 millisec */ + break; + case IXGBE_PCIDEVCTRL2_260_520ms: + pollcnt = 5200; /* 520 millisec */ + break; + case IXGBE_PCIDEVCTRL2_1_2s: + pollcnt = 20000; /* 2 sec */ + break; + case IXGBE_PCIDEVCTRL2_4_8s: + pollcnt = 80000; /* 8 sec */ + break; + case IXGBE_PCIDEVCTRL2_17_34s: + pollcnt = 34000; /* 34 sec */ + break; + case IXGBE_PCIDEVCTRL2_50_100us: /* 100 microsecs */ + case IXGBE_PCIDEVCTRL2_1_2ms: /* 2 millisecs */ + case IXGBE_PCIDEVCTRL2_16_32ms: /* 32 millisec */ + case IXGBE_PCIDEVCTRL2_16_32ms_def: /* 32 millisec default */ + default: + pollcnt = 800; /* 80 millisec minimum */ + break; + } + + /* add 10% to spec maximum */ + return (pollcnt * 11) / 10; +} + +/** + * ixgbe_disable_pcie_primary - Disable PCI-express primary access + * @hw: pointer to hardware structure + * + * Disables PCI-Express primary access and verifies there are no pending + * requests. IXGBE_ERR_PRIMARY_REQUESTS_PENDING is returned if primary disable + * bit hasn't caused the primary requests to be disabled, else 0 + * is returned signifying primary requests disabled. + **/ +static s32 ixgbe_disable_pcie_primary(struct ixgbe_hw *hw) +{ + u32 i, poll; + u16 value; + + /* Always set this bit to ensure any future transactions are blocked */ + IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS); + + /* Poll for bit to read as set */ + for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) { + if (IXGBE_READ_REG(hw, IXGBE_CTRL) & IXGBE_CTRL_GIO_DIS) + break; + usleep_range(100, 120); + } + if (i >= IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT) { + hw_dbg(hw, "GIO disable did not set - requesting resets\n"); + goto gio_disable_fail; + } + + /* Exit if primary requests are blocked */ + if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) || + ixgbe_removed(hw->hw_addr)) + return 0; + + /* Poll for primary request bit to clear */ + for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) { + udelay(100); + if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO)) + return 0; + } + + /* + * Two consecutive resets are required via CTRL.RST per datasheet + * 5.2.5.3.2 Primary Disable. We set a flag to inform the reset routine + * of this need. The first reset prevents new primary requests from + * being issued by our device. We then must wait 1usec or more for any + * remaining completions from the PCIe bus to trickle in, and then reset + * again to clear out any effects they may have had on our device. + */ + hw_dbg(hw, "GIO Primary Disable bit didn't clear - requesting resets\n"); +gio_disable_fail: + hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; + + if (hw->mac.type >= ixgbe_mac_X550) + return 0; + + /* + * Before proceeding, make sure that the PCIe block does not have + * transactions pending. + */ + poll = ixgbe_pcie_timeout_poll(hw); + for (i = 0; i < poll; i++) { + udelay(100); + value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS); + if (ixgbe_removed(hw->hw_addr)) + return 0; + if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING)) + return 0; + } + + hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n"); + return IXGBE_ERR_PRIMARY_REQUESTS_PENDING; +} + +/** + * ixgbe_acquire_swfw_sync - Acquire SWFW semaphore + * @hw: pointer to hardware structure + * @mask: Mask to specify which semaphore to acquire + * + * Acquires the SWFW semaphore through the GSSR register for the specified + * function (CSR, PHY0, PHY1, EEPROM, Flash) + **/ +s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask) +{ + u32 gssr = 0; + u32 swmask = mask; + u32 fwmask = mask << 5; + u32 timeout = 200; + u32 i; + + for (i = 0; i < timeout; i++) { + /* + * SW NVM semaphore bit is used for access to all + * SW_FW_SYNC bits (not just NVM) + */ + if (ixgbe_get_eeprom_semaphore(hw)) + return IXGBE_ERR_SWFW_SYNC; + + gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); + if (!(gssr & (fwmask | swmask))) { + gssr |= swmask; + IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); + ixgbe_release_eeprom_semaphore(hw); + return 0; + } else { + /* Resource is currently in use by FW or SW */ + ixgbe_release_eeprom_semaphore(hw); + usleep_range(5000, 10000); + } + } + + /* If time expired clear the bits holding the lock and retry */ + if (gssr & (fwmask | swmask)) + ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask)); + + usleep_range(5000, 10000); + return IXGBE_ERR_SWFW_SYNC; +} + +/** + * ixgbe_release_swfw_sync - Release SWFW semaphore + * @hw: pointer to hardware structure + * @mask: Mask to specify which semaphore to release + * + * Releases the SWFW semaphore through the GSSR register for the specified + * function (CSR, PHY0, PHY1, EEPROM, Flash) + **/ +void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask) +{ + u32 gssr; + u32 swmask = mask; + + ixgbe_get_eeprom_semaphore(hw); + + gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); + gssr &= ~swmask; + IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); + + ixgbe_release_eeprom_semaphore(hw); +} + +/** + * prot_autoc_read_generic - Hides MAC differences needed for AUTOC read + * @hw: pointer to hardware structure + * @reg_val: Value we read from AUTOC + * @locked: bool to indicate whether the SW/FW lock should be taken. Never + * true in this the generic case. + * + * The default case requires no protection so just to the register read. + **/ +s32 prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val) +{ + *locked = false; + *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC); + return 0; +} + +/** + * prot_autoc_write_generic - Hides MAC differences needed for AUTOC write + * @hw: pointer to hardware structure + * @reg_val: value to write to AUTOC + * @locked: bool to indicate whether the SW/FW lock was already taken by + * previous read. + **/ +s32 prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked) +{ + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val); + return 0; +} + +/** + * ixgbe_disable_rx_buff_generic - Stops the receive data path + * @hw: pointer to hardware structure + * + * Stops the receive data path and waits for the HW to internally + * empty the Rx security block. + **/ +s32 ixgbe_disable_rx_buff_generic(struct ixgbe_hw *hw) +{ +#define IXGBE_MAX_SECRX_POLL 40 + int i; + int secrxreg; + + secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); + secrxreg |= IXGBE_SECRXCTRL_RX_DIS; + IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg); + for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) { + secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT); + if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY) + break; + else + /* Use interrupt-safe sleep just in case */ + udelay(1000); + } + + /* For informational purposes only */ + if (i >= IXGBE_MAX_SECRX_POLL) + hw_dbg(hw, "Rx unit being enabled before security path fully disabled. Continuing with init.\n"); + + return 0; + +} + +/** + * ixgbe_enable_rx_buff_generic - Enables the receive data path + * @hw: pointer to hardware structure + * + * Enables the receive data path + **/ +s32 ixgbe_enable_rx_buff_generic(struct ixgbe_hw *hw) +{ + u32 secrxreg; + + secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); + secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS; + IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg); + IXGBE_WRITE_FLUSH(hw); + + return 0; +} + +/** + * ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit + * @hw: pointer to hardware structure + * @regval: register value to write to RXCTRL + * + * Enables the Rx DMA unit + **/ +s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval) +{ + if (regval & IXGBE_RXCTRL_RXEN) + hw->mac.ops.enable_rx(hw); + else + hw->mac.ops.disable_rx(hw); + + return 0; +} + +/** + * ixgbe_blink_led_start_generic - Blink LED based on index. + * @hw: pointer to hardware structure + * @index: led number to blink + **/ +s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index) +{ + ixgbe_link_speed speed = 0; + bool link_up = false; + u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + bool locked = false; + s32 ret_val; + + if (index > 3) + return IXGBE_ERR_PARAM; + + /* + * Link must be up to auto-blink the LEDs; + * Force it if link is down. + */ + hw->mac.ops.check_link(hw, &speed, &link_up, false); + + if (!link_up) { + ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg); + if (ret_val) + return ret_val; + + autoc_reg |= IXGBE_AUTOC_AN_RESTART; + autoc_reg |= IXGBE_AUTOC_FLU; + + ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked); + if (ret_val) + return ret_val; + + IXGBE_WRITE_FLUSH(hw); + + usleep_range(10000, 20000); + } + + led_reg &= ~IXGBE_LED_MODE_MASK(index); + led_reg |= IXGBE_LED_BLINK(index); + IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); + IXGBE_WRITE_FLUSH(hw); + + return 0; +} + +/** + * ixgbe_blink_led_stop_generic - Stop blinking LED based on index. + * @hw: pointer to hardware structure + * @index: led number to stop blinking + **/ +s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index) +{ + u32 autoc_reg = 0; + u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); + bool locked = false; + s32 ret_val; + + if (index > 3) + return IXGBE_ERR_PARAM; + + ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg); + if (ret_val) + return ret_val; + + autoc_reg &= ~IXGBE_AUTOC_FLU; + autoc_reg |= IXGBE_AUTOC_AN_RESTART; + + ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked); + if (ret_val) + return ret_val; + + led_reg &= ~IXGBE_LED_MODE_MASK(index); + led_reg &= ~IXGBE_LED_BLINK(index); + led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index); + IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); + IXGBE_WRITE_FLUSH(hw); + + return 0; +} + +/** + * ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM + * @hw: pointer to hardware structure + * @san_mac_offset: SAN MAC address offset + * + * This function will read the EEPROM location for the SAN MAC address + * pointer, and returns the value at that location. This is used in both + * get and set mac_addr routines. + **/ +static s32 ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw, + u16 *san_mac_offset) +{ + s32 ret_val; + + /* + * First read the EEPROM pointer to see if the MAC addresses are + * available. + */ + ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR, + san_mac_offset); + if (ret_val) + hw_err(hw, "eeprom read at offset %d failed\n", + IXGBE_SAN_MAC_ADDR_PTR); + + return ret_val; +} + +/** + * ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM + * @hw: pointer to hardware structure + * @san_mac_addr: SAN MAC address + * + * Reads the SAN MAC address from the EEPROM, if it's available. This is + * per-port, so set_lan_id() must be called before reading the addresses. + * set_lan_id() is called by identify_sfp(), but this cannot be relied + * upon for non-SFP connections, so we must call it here. + **/ +s32 ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr) +{ + u16 san_mac_data, san_mac_offset; + u8 i; + s32 ret_val; + + /* + * First read the EEPROM pointer to see if the MAC addresses are + * available. If they're not, no point in calling set_lan_id() here. + */ + ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset); + if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF) + + goto san_mac_addr_clr; + + /* make sure we know which port we need to program */ + hw->mac.ops.set_lan_id(hw); + /* apply the port offset to the address offset */ + (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) : + (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET); + for (i = 0; i < 3; i++) { + ret_val = hw->eeprom.ops.read(hw, san_mac_offset, + &san_mac_data); + if (ret_val) { + hw_err(hw, "eeprom read at offset %d failed\n", + san_mac_offset); + goto san_mac_addr_clr; + } + san_mac_addr[i * 2] = (u8)(san_mac_data); + san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8); + san_mac_offset++; + } + return 0; + +san_mac_addr_clr: + /* No addresses available in this EEPROM. It's not necessarily an + * error though, so just wipe the local address and return. + */ + for (i = 0; i < 6; i++) + san_mac_addr[i] = 0xFF; + return ret_val; +} + +/** + * ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count + * @hw: pointer to hardware structure + * + * Read PCIe configuration space, and get the MSI-X vector count from + * the capabilities table. + **/ +u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw) +{ + u16 msix_count; + u16 max_msix_count; + u16 pcie_offset; + + switch (hw->mac.type) { + case ixgbe_mac_82598EB: + pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS; + max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598; + break; + case ixgbe_mac_82599EB: + case ixgbe_mac_X540: + case ixgbe_mac_X550: + case ixgbe_mac_X550EM_x: + case ixgbe_mac_x550em_a: + pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS; + max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599; + break; + default: + return 1; + } + + msix_count = ixgbe_read_pci_cfg_word(hw, pcie_offset); + if (ixgbe_removed(hw->hw_addr)) + msix_count = 0; + msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK; + + /* MSI-X count is zero-based in HW */ + msix_count++; + + if (msix_count > max_msix_count) + msix_count = max_msix_count; + + return msix_count; +} + +/** + * ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address + * @hw: pointer to hardware struct + * @rar: receive address register index to disassociate + * @vmdq: VMDq pool index to remove from the rar + **/ +s32 ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq) +{ + u32 mpsar_lo, mpsar_hi; + u32 rar_entries = hw->mac.num_rar_entries; + + /* Make sure we are using a valid rar index range */ + if (rar >= rar_entries) { + hw_dbg(hw, "RAR index %d is out of range.\n", rar); + return IXGBE_ERR_INVALID_ARGUMENT; + } + + mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar)); + mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar)); + + if (ixgbe_removed(hw->hw_addr)) + return 0; + + if (!mpsar_lo && !mpsar_hi) + return 0; + + if (vmdq == IXGBE_CLEAR_VMDQ_ALL) { + if (mpsar_lo) { + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0); + mpsar_lo = 0; + } + if (mpsar_hi) { + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0); + mpsar_hi = 0; + } + } else if (vmdq < 32) { + mpsar_lo &= ~BIT(vmdq); + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo); + } else { + mpsar_hi &= ~BIT(vmdq - 32); + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi); + } + + /* was that the last pool using this rar? */ + if (mpsar_lo == 0 && mpsar_hi == 0 && + rar != 0 && rar != hw->mac.san_mac_rar_index) + hw->mac.ops.clear_rar(hw, rar); + + return 0; +} + +/** + * ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address + * @hw: pointer to hardware struct + * @rar: receive address register index to associate with a VMDq index + * @vmdq: VMDq pool index + **/ +s32 ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq) +{ + u32 mpsar; + u32 rar_entries = hw->mac.num_rar_entries; + + /* Make sure we are using a valid rar index range */ + if (rar >= rar_entries) { + hw_dbg(hw, "RAR index %d is out of range.\n", rar); + return IXGBE_ERR_INVALID_ARGUMENT; + } + + if (vmdq < 32) { + mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar)); + mpsar |= BIT(vmdq); + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar); + } else { + mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar)); + mpsar |= BIT(vmdq - 32); + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar); + } + return 0; +} + +/** + * ixgbe_set_vmdq_san_mac_generic - Associate VMDq pool index with a rx address + * @hw: pointer to hardware struct + * @vmdq: VMDq pool index + * + * This function should only be involved in the IOV mode. + * In IOV mode, Default pool is next pool after the number of + * VFs advertized and not 0. + * MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index] + **/ +s32 ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq) +{ + u32 rar = hw->mac.san_mac_rar_index; + + if (vmdq < 32) { + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), BIT(vmdq)); + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0); + } else { + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0); + IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), BIT(vmdq - 32)); + } + + return 0; +} + +/** + * ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array + * @hw: pointer to hardware structure + **/ +s32 ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw) +{ + int i; + + for (i = 0; i < 128; i++) + IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0); + + return 0; +} + +/** + * ixgbe_find_vlvf_slot - find the vlanid or the first empty slot + * @hw: pointer to hardware structure + * @vlan: VLAN id to write to VLAN filter + * @vlvf_bypass: true to find vlanid only, false returns first empty slot if + * vlanid not found + * + * return the VLVF index where this VLAN id should be placed + * + **/ +static s32 ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan, bool vlvf_bypass) +{ + s32 regindex, first_empty_slot; + u32 bits; + + /* short cut the special case */ + if (vlan == 0) + return 0; + + /* if vlvf_bypass is set we don't want to use an empty slot, we + * will simply bypass the VLVF if there are no entries present in the + * VLVF that contain our VLAN + */ + first_empty_slot = vlvf_bypass ? IXGBE_ERR_NO_SPACE : 0; + + /* add VLAN enable bit for comparison */ + vlan |= IXGBE_VLVF_VIEN; + + /* Search for the vlan id in the VLVF entries. Save off the first empty + * slot found along the way. + * + * pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1 + */ + for (regindex = IXGBE_VLVF_ENTRIES; --regindex;) { + bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex)); + if (bits == vlan) + return regindex; + if (!first_empty_slot && !bits) + first_empty_slot = regindex; + } + + /* If we are here then we didn't find the VLAN. Return first empty + * slot we found during our search, else error. + */ + if (!first_empty_slot) + hw_dbg(hw, "No space in VLVF.\n"); + + return first_empty_slot ? : IXGBE_ERR_NO_SPACE; +} + +/** + * ixgbe_set_vfta_generic - Set VLAN filter table + * @hw: pointer to hardware structure + * @vlan: VLAN id to write to VLAN filter + * @vind: VMDq output index that maps queue to VLAN id in VFVFB + * @vlan_on: boolean flag to turn on/off VLAN in VFVF + * @vlvf_bypass: boolean flag indicating updating default pool is okay + * + * Turn on/off specified VLAN in the VLAN filter table. + **/ +s32 ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind, + bool vlan_on, bool vlvf_bypass) +{ + u32 regidx, vfta_delta, vfta, bits; + s32 vlvf_index; + + if ((vlan > 4095) || (vind > 63)) + return IXGBE_ERR_PARAM; + + /* + * this is a 2 part operation - first the VFTA, then the + * VLVF and VLVFB if VT Mode is set + * We don't write the VFTA until we know the VLVF part succeeded. + */ + + /* Part 1 + * The VFTA is a bitstring made up of 128 32-bit registers + * that enable the particular VLAN id, much like the MTA: + * bits[11-5]: which register + * bits[4-0]: which bit in the register + */ + regidx = vlan / 32; + vfta_delta = BIT(vlan % 32); + vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx)); + + /* vfta_delta represents the difference between the current value + * of vfta and the value we want in the register. Since the diff + * is an XOR mask we can just update vfta using an XOR. + */ + vfta_delta &= vlan_on ? ~vfta : vfta; + vfta ^= vfta_delta; + + /* Part 2 + * If VT Mode is set + * Either vlan_on + * make sure the vlan is in VLVF + * set the vind bit in the matching VLVFB + * Or !vlan_on + * clear the pool bit and possibly the vind + */ + if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE)) + goto vfta_update; + + vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass); + if (vlvf_index < 0) { + if (vlvf_bypass) + goto vfta_update; + return vlvf_index; + } + + bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32)); + + /* set the pool bit */ + bits |= BIT(vind % 32); + if (vlan_on) + goto vlvf_update; + + /* clear the pool bit */ + bits ^= BIT(vind % 32); + + if (!bits && + !IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + 1 - vind / 32))) { + /* Clear VFTA first, then disable VLVF. Otherwise + * we run the risk of stray packets leaking into + * the PF via the default pool + */ + if (vfta_delta) + IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta); + + /* disable VLVF and clear remaining bit from pool */ + IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0); + IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), 0); + + return 0; + } + + /* If there are still bits set in the VLVFB registers + * for the VLAN ID indicated we need to see if the + * caller is requesting that we clear the VFTA entry bit. + * If the caller has requested that we clear the VFTA + * entry bit but there are still pools/VFs using this VLAN + * ID entry then ignore the request. We're not worried + * about the case where we're turning the VFTA VLAN ID + * entry bit on, only when requested to turn it off as + * there may be multiple pools and/or VFs using the + * VLAN ID entry. In that case we cannot clear the + * VFTA bit until all pools/VFs using that VLAN ID have also + * been cleared. This will be indicated by "bits" being + * zero. + */ + vfta_delta = 0; + +vlvf_update: + /* record pool change and enable VLAN ID if not already enabled */ + IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), bits); + IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), IXGBE_VLVF_VIEN | vlan); + +vfta_update: + /* Update VFTA now that we are ready for traffic */ + if (vfta_delta) + IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta); + + return 0; +} + +/** + * ixgbe_clear_vfta_generic - Clear VLAN filter table + * @hw: pointer to hardware structure + * + * Clears the VLAN filter table, and the VMDq index associated with the filter + **/ +s32 ixgbe_clear_vfta_generic(struct ixgbe_hw *hw) +{ + u32 offset; + + for (offset = 0; offset < hw->mac.vft_size; offset++) + IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0); + + for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) { + IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0); + IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0); + IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2 + 1), 0); + } + + return 0; +} + +/** + * ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix + * @hw: pointer to hardware structure + * + * Contains the logic to identify if we need to verify link for the + * crosstalk fix + **/ +static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw) +{ + /* Does FW say we need the fix */ + if (!hw->need_crosstalk_fix) + return false; + + /* Only consider SFP+ PHYs i.e. media type fiber */ + switch (hw->mac.ops.get_media_type(hw)) { + case ixgbe_media_type_fiber: + case ixgbe_media_type_fiber_qsfp: + break; + default: + return false; + } + + return true; +} + +/** + * ixgbe_check_mac_link_generic - Determine link and speed status + * @hw: pointer to hardware structure + * @speed: pointer to link speed + * @link_up: true when link is up + * @link_up_wait_to_complete: bool used to wait for link up or not + * + * Reads the links register to determine if link is up and the current speed + **/ +s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed, + bool *link_up, bool link_up_wait_to_complete) +{ + bool crosstalk_fix_active = ixgbe_need_crosstalk_fix(hw); + u32 links_reg, links_orig; + u32 i; + + /* If Crosstalk fix enabled do the sanity check of making sure + * the SFP+ cage is full. + */ + if (crosstalk_fix_active) { + u32 sfp_cage_full; + + switch (hw->mac.type) { + case ixgbe_mac_82599EB: + sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) & + IXGBE_ESDP_SDP2; + break; + case ixgbe_mac_X550EM_x: + case ixgbe_mac_x550em_a: + sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) & + IXGBE_ESDP_SDP0; + break; + default: + /* sanity check - No SFP+ devices here */ + sfp_cage_full = false; + break; + } + + if (!sfp_cage_full) { + *link_up = false; + *speed = IXGBE_LINK_SPEED_UNKNOWN; + return 0; + } + } + + /* clear the old state */ + links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS); + + links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); + + if (links_orig != links_reg) { + hw_dbg(hw, "LINKS changed from %08X to %08X\n", + links_orig, links_reg); + } + + if (link_up_wait_to_complete) { + for (i = 0; i < IXGBE_LINK_UP_TIME; i++) { + if (links_reg & IXGBE_LINKS_UP) { + *link_up = true; + break; + } else { + *link_up = false; + } + msleep(100); + links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); + } + } else { + if (links_reg & IXGBE_LINKS_UP) { + if (crosstalk_fix_active) { + /* Check the link state again after a delay + * to filter out spurious link up + * notifications. + */ + mdelay(5); + links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); + if (!(links_reg & IXGBE_LINKS_UP)) { + *link_up = false; + *speed = IXGBE_LINK_SPEED_UNKNOWN; + return 0; + } + } + *link_up = true; + } else { + *link_up = false; + } + } + + switch (links_reg & IXGBE_LINKS_SPEED_82599) { + case IXGBE_LINKS_SPEED_10G_82599: + if ((hw->mac.type >= ixgbe_mac_X550) && + (links_reg & IXGBE_LINKS_SPEED_NON_STD)) + *speed = IXGBE_LINK_SPEED_2_5GB_FULL; + else + *speed = IXGBE_LINK_SPEED_10GB_FULL; + break; + case IXGBE_LINKS_SPEED_1G_82599: + *speed = IXGBE_LINK_SPEED_1GB_FULL; + break; + case IXGBE_LINKS_SPEED_100_82599: + if ((hw->mac.type >= ixgbe_mac_X550) && + (links_reg & IXGBE_LINKS_SPEED_NON_STD)) + *speed = IXGBE_LINK_SPEED_5GB_FULL; + else + *speed = IXGBE_LINK_SPEED_100_FULL; + break; + case IXGBE_LINKS_SPEED_10_X550EM_A: + *speed = IXGBE_LINK_SPEED_UNKNOWN; + if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T || + hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) { + *speed = IXGBE_LINK_SPEED_10_FULL; + } + break; + default: + *speed = IXGBE_LINK_SPEED_UNKNOWN; + } + + return 0; +} + +/** + * ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from + * the EEPROM + * @hw: pointer to hardware structure + * @wwnn_prefix: the alternative WWNN prefix + * @wwpn_prefix: the alternative WWPN prefix + * + * This function will read the EEPROM from the alternative SAN MAC address + * block to check the support for the alternative WWNN/WWPN prefix support. + **/ +s32 ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix, + u16 *wwpn_prefix) +{ + u16 offset, caps; + u16 alt_san_mac_blk_offset; + + /* clear output first */ + *wwnn_prefix = 0xFFFF; + *wwpn_prefix = 0xFFFF; + + /* check if alternative SAN MAC is supported */ + offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR; + if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset)) + goto wwn_prefix_err; + + if ((alt_san_mac_blk_offset == 0) || + (alt_san_mac_blk_offset == 0xFFFF)) + return 0; + + /* check capability in alternative san mac address block */ + offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET; + if (hw->eeprom.ops.read(hw, offset, &caps)) + goto wwn_prefix_err; + if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN)) + return 0; + + /* get the corresponding prefix for WWNN/WWPN */ + offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET; + if (hw->eeprom.ops.read(hw, offset, wwnn_prefix)) + hw_err(hw, "eeprom read at offset %d failed\n", offset); + + offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET; + if (hw->eeprom.ops.read(hw, offset, wwpn_prefix)) + goto wwn_prefix_err; + + return 0; + +wwn_prefix_err: + hw_err(hw, "eeprom read at offset %d failed\n", offset); + return 0; +} + +/** + * ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing + * @hw: pointer to hardware structure + * @enable: enable or disable switch for MAC anti-spoofing + * @vf: Virtual Function pool - VF Pool to set for MAC anti-spoofing + * + **/ +void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf) +{ + int vf_target_reg = vf >> 3; + int vf_target_shift = vf % 8; + u32 pfvfspoof; + + if (hw->mac.type == ixgbe_mac_82598EB) + return; + + pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); + if (enable) + pfvfspoof |= BIT(vf_target_shift); + else + pfvfspoof &= ~BIT(vf_target_shift); + IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof); +} + +/** + * ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing + * @hw: pointer to hardware structure + * @enable: enable or disable switch for VLAN anti-spoofing + * @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing + * + **/ +void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf) +{ + int vf_target_reg = vf >> 3; + int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT; + u32 pfvfspoof; + + if (hw->mac.type == ixgbe_mac_82598EB) + return; + + pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); + if (enable) + pfvfspoof |= BIT(vf_target_shift); + else + pfvfspoof &= ~BIT(vf_target_shift); + IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof); +} + +/** + * ixgbe_get_device_caps_generic - Get additional device capabilities + * @hw: pointer to hardware structure + * @device_caps: the EEPROM word with the extra device capabilities + * + * This function will read the EEPROM location for the device capabilities, + * and return the word through device_caps. + **/ +s32 ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps) +{ + hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps); + + return 0; +} + +/** + * ixgbe_set_rxpba_generic - Initialize RX packet buffer + * @hw: pointer to hardware structure + * @num_pb: number of packet buffers to allocate + * @headroom: reserve n KB of headroom + * @strategy: packet buffer allocation strategy + **/ +void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw, + int num_pb, + u32 headroom, + int strategy) +{ + u32 pbsize = hw->mac.rx_pb_size; + int i = 0; + u32 rxpktsize, txpktsize, txpbthresh; + + /* Reserve headroom */ + pbsize -= headroom; + + if (!num_pb) + num_pb = 1; + + /* Divide remaining packet buffer space amongst the number + * of packet buffers requested using supplied strategy. + */ + switch (strategy) { + case (PBA_STRATEGY_WEIGHTED): + /* pba_80_48 strategy weight first half of packet buffer with + * 5/8 of the packet buffer space. + */ + rxpktsize = ((pbsize * 5 * 2) / (num_pb * 8)); + pbsize -= rxpktsize * (num_pb / 2); + rxpktsize <<= IXGBE_RXPBSIZE_SHIFT; + for (; i < (num_pb / 2); i++) + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); + fallthrough; /* configure remaining packet buffers */ + case (PBA_STRATEGY_EQUAL): + /* Divide the remaining Rx packet buffer evenly among the TCs */ + rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT; + for (; i < num_pb; i++) + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); + break; + default: + break; + } + + /* + * Setup Tx packet buffer and threshold equally for all TCs + * TXPBTHRESH register is set in K so divide by 1024 and subtract + * 10 since the largest packet we support is just over 9K. + */ + txpktsize = IXGBE_TXPBSIZE_MAX / num_pb; + txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX; + for (i = 0; i < num_pb; i++) { + IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize); + IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh); + } + + /* Clear unused TCs, if any, to zero buffer size*/ + for (; i < IXGBE_MAX_PB; i++) { + IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0); + IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0); + IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0); + } +} + +/** + * ixgbe_calculate_checksum - Calculate checksum for buffer + * @buffer: pointer to EEPROM + * @length: size of EEPROM to calculate a checksum for + * + * Calculates the checksum for some buffer on a specified length. The + * checksum calculated is returned. + **/ +u8 ixgbe_calculate_checksum(u8 *buffer, u32 length) +{ + u32 i; + u8 sum = 0; + + if (!buffer) + return 0; + + for (i = 0; i < length; i++) + sum += buffer[i]; + + return (u8) (0 - sum); +} + +/** + * ixgbe_hic_unlocked - Issue command to manageability block unlocked + * @hw: pointer to the HW structure + * @buffer: command to write and where the return status will be placed + * @length: length of buffer, must be multiple of 4 bytes + * @timeout: time in ms to wait for command completion + * + * Communicates with the manageability block. On success return 0 + * else returns semaphore error when encountering an error acquiring + * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. + * + * This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held + * by the caller. + **/ +s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length, + u32 timeout) +{ + u32 hicr, i, fwsts; + u16 dword_len; + + if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { + hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length); + return IXGBE_ERR_HOST_INTERFACE_COMMAND; + } + + /* Set bit 9 of FWSTS clearing FW reset indication */ + fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS); + IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI); + + /* Check that the host interface is enabled. */ + hicr = IXGBE_READ_REG(hw, IXGBE_HICR); + if (!(hicr & IXGBE_HICR_EN)) { + hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n"); + return IXGBE_ERR_HOST_INTERFACE_COMMAND; + } + + /* Calculate length in DWORDs. We must be DWORD aligned */ + if (length % sizeof(u32)) { + hw_dbg(hw, "Buffer length failure, not aligned to dword"); + return IXGBE_ERR_INVALID_ARGUMENT; + } + + dword_len = length >> 2; + + /* The device driver writes the relevant command block + * into the ram area. + */ + for (i = 0; i < dword_len; i++) + IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG, + i, (__force u32)cpu_to_le32(buffer[i])); + + /* Setting this bit tells the ARC that a new command is pending. */ + IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C); + + for (i = 0; i < timeout; i++) { + hicr = IXGBE_READ_REG(hw, IXGBE_HICR); + if (!(hicr & IXGBE_HICR_C)) + break; + usleep_range(1000, 2000); + } + + /* Check command successful completion. */ + if ((timeout && i == timeout) || + !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) + return IXGBE_ERR_HOST_INTERFACE_COMMAND; + + return 0; +} + +/** + * ixgbe_host_interface_command - Issue command to manageability block + * @hw: pointer to the HW structure + * @buffer: contains the command to write and where the return status will + * be placed + * @length: length of buffer, must be multiple of 4 bytes + * @timeout: time in ms to wait for command completion + * @return_data: read and return data from the buffer (true) or not (false) + * Needed because FW structures are big endian and decoding of + * these fields can be 8 bit or 16 bit based on command. Decoding + * is not easily understood without making a table of commands. + * So we will leave this up to the caller to read back the data + * in these cases. + * + * Communicates with the manageability block. On success return 0 + * else return IXGBE_ERR_HOST_INTERFACE_COMMAND. + **/ +s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer, + u32 length, u32 timeout, + bool return_data) +{ + u32 hdr_size = sizeof(struct ixgbe_hic_hdr); + struct ixgbe_hic_hdr *hdr = buffer; + u32 *u32arr = buffer; + u16 buf_len, dword_len; + s32 status; + u32 bi; + + if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { + hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length); + return IXGBE_ERR_HOST_INTERFACE_COMMAND; + } + /* Take management host interface semaphore */ + status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); + if (status) + return status; + + status = ixgbe_hic_unlocked(hw, buffer, length, timeout); + if (status) + goto rel_out; + + if (!return_data) + goto rel_out; + + /* Calculate length in DWORDs */ + dword_len = hdr_size >> 2; + + /* first pull in the header so we know the buffer length */ + for (bi = 0; bi < dword_len; bi++) { + u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); + le32_to_cpus(&u32arr[bi]); + } + + /* If there is any thing in data position pull it in */ + buf_len = hdr->buf_len; + if (!buf_len) + goto rel_out; + + if (length < round_up(buf_len, 4) + hdr_size) { + hw_dbg(hw, "Buffer not large enough for reply message.\n"); + status = IXGBE_ERR_HOST_INTERFACE_COMMAND; + goto rel_out; + } + + /* Calculate length in DWORDs, add 3 for odd lengths */ + dword_len = (buf_len + 3) >> 2; + + /* Pull in the rest of the buffer (bi is where we left off) */ + for (; bi <= dword_len; bi++) { + u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); + le32_to_cpus(&u32arr[bi]); + } + +rel_out: + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); + + return status; +} + +/** + * ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware + * @hw: pointer to the HW structure + * @maj: driver version major number + * @min: driver version minor number + * @build: driver version build number + * @sub: driver version sub build number + * @len: length of driver_ver string + * @driver_ver: driver string + * + * Sends driver version number to firmware through the manageability + * block. On success return 0 + * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring + * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. + **/ +s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min, + u8 build, u8 sub, __always_unused u16 len, + __always_unused const char *driver_ver) +{ + struct ixgbe_hic_drv_info fw_cmd; + int i; + s32 ret_val; + + fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO; + fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN; + fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED; + fw_cmd.port_num = hw->bus.func; + fw_cmd.ver_maj = maj; + fw_cmd.ver_min = min; + fw_cmd.ver_build = build; + fw_cmd.ver_sub = sub; + fw_cmd.hdr.checksum = 0; + fw_cmd.pad = 0; + fw_cmd.pad2 = 0; + fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd, + (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len)); + + for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) { + ret_val = ixgbe_host_interface_command(hw, &fw_cmd, + sizeof(fw_cmd), + IXGBE_HI_COMMAND_TIMEOUT, + true); + if (ret_val != 0) + continue; + + if (fw_cmd.hdr.cmd_or_resp.ret_status == + FW_CEM_RESP_STATUS_SUCCESS) + ret_val = 0; + else + ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND; + + break; + } + + return ret_val; +} + +/** + * ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo + * @hw: pointer to the hardware structure + * + * The 82599 and x540 MACs can experience issues if TX work is still pending + * when a reset occurs. This function prevents this by flushing the PCIe + * buffers on the system. + **/ +void ixgbe_clear_tx_pending(struct ixgbe_hw *hw) +{ + u32 gcr_ext, hlreg0, i, poll; + u16 value; + + /* + * If double reset is not requested then all transactions should + * already be clear and as such there is no work to do + */ + if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED)) + return; + + /* + * Set loopback enable to prevent any transmits from being sent + * should the link come up. This assumes that the RXCTRL.RXEN bit + * has already been cleared. + */ + hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0); + IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK); + + /* wait for a last completion before clearing buffers */ + IXGBE_WRITE_FLUSH(hw); + usleep_range(3000, 6000); + + /* Before proceeding, make sure that the PCIe block does not have + * transactions pending. + */ + poll = ixgbe_pcie_timeout_poll(hw); + for (i = 0; i < poll; i++) { + usleep_range(100, 200); + value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS); + if (ixgbe_removed(hw->hw_addr)) + break; + if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING)) + break; + } + + /* initiate cleaning flow for buffers in the PCIe transaction layer */ + gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT); + IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, + gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR); + + /* Flush all writes and allow 20usec for all transactions to clear */ + IXGBE_WRITE_FLUSH(hw); + udelay(20); + + /* restore previous register values */ + IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext); + IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0); +} + +static const u8 ixgbe_emc_temp_data[4] = { + IXGBE_EMC_INTERNAL_DATA, + IXGBE_EMC_DIODE1_DATA, + IXGBE_EMC_DIODE2_DATA, + IXGBE_EMC_DIODE3_DATA +}; +static const u8 ixgbe_emc_therm_limit[4] = { + IXGBE_EMC_INTERNAL_THERM_LIMIT, + IXGBE_EMC_DIODE1_THERM_LIMIT, + IXGBE_EMC_DIODE2_THERM_LIMIT, + IXGBE_EMC_DIODE3_THERM_LIMIT +}; + +/** + * ixgbe_get_ets_data - Extracts the ETS bit data + * @hw: pointer to hardware structure + * @ets_cfg: extected ETS data + * @ets_offset: offset of ETS data + * + * Returns error code. + **/ +static s32 ixgbe_get_ets_data(struct ixgbe_hw *hw, u16 *ets_cfg, + u16 *ets_offset) +{ + s32 status; + + status = hw->eeprom.ops.read(hw, IXGBE_ETS_CFG, ets_offset); + if (status) + return status; + + if ((*ets_offset == 0x0000) || (*ets_offset == 0xFFFF)) + return IXGBE_NOT_IMPLEMENTED; + + status = hw->eeprom.ops.read(hw, *ets_offset, ets_cfg); + if (status) + return status; + + if ((*ets_cfg & IXGBE_ETS_TYPE_MASK) != IXGBE_ETS_TYPE_EMC_SHIFTED) + return IXGBE_NOT_IMPLEMENTED; + + return 0; +} + +/** + * ixgbe_get_thermal_sensor_data_generic - Gathers thermal sensor data + * @hw: pointer to hardware structure + * + * Returns the thermal sensor data structure + **/ +s32 ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw) +{ + s32 status; + u16 ets_offset; + u16 ets_cfg; + u16 ets_sensor; + u8 num_sensors; + u8 i; + struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data; + + /* Only support thermal sensors attached to physical port 0 */ + if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1)) + return IXGBE_NOT_IMPLEMENTED; + + status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset); + if (status) + return status; + + num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK); + if (num_sensors > IXGBE_MAX_SENSORS) + num_sensors = IXGBE_MAX_SENSORS; + + for (i = 0; i < num_sensors; i++) { + u8 sensor_index; + u8 sensor_location; + + status = hw->eeprom.ops.read(hw, (ets_offset + 1 + i), + &ets_sensor); + if (status) + return status; + + sensor_index = ((ets_sensor & IXGBE_ETS_DATA_INDEX_MASK) >> + IXGBE_ETS_DATA_INDEX_SHIFT); + sensor_location = ((ets_sensor & IXGBE_ETS_DATA_LOC_MASK) >> + IXGBE_ETS_DATA_LOC_SHIFT); + + if (sensor_location != 0) { + status = hw->phy.ops.read_i2c_byte(hw, + ixgbe_emc_temp_data[sensor_index], + IXGBE_I2C_THERMAL_SENSOR_ADDR, + &data->sensor[i].temp); + if (status) + return status; + } + } + + return 0; +} + +/** + * ixgbe_init_thermal_sensor_thresh_generic - Inits thermal sensor thresholds + * @hw: pointer to hardware structure + * + * Inits the thermal sensor thresholds according to the NVM map + * and save off the threshold and location values into mac.thermal_sensor_data + **/ +s32 ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw) +{ + s32 status; + u16 ets_offset; + u16 ets_cfg; + u16 ets_sensor; + u8 low_thresh_delta; + u8 num_sensors; + u8 therm_limit; + u8 i; + struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data; + + memset(data, 0, sizeof(struct ixgbe_thermal_sensor_data)); + + /* Only support thermal sensors attached to physical port 0 */ + if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1)) + return IXGBE_NOT_IMPLEMENTED; + + status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset); + if (status) + return status; + + low_thresh_delta = ((ets_cfg & IXGBE_ETS_LTHRES_DELTA_MASK) >> + IXGBE_ETS_LTHRES_DELTA_SHIFT); + num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK); + if (num_sensors > IXGBE_MAX_SENSORS) + num_sensors = IXGBE_MAX_SENSORS; + + for (i = 0; i < num_sensors; i++) { + u8 sensor_index; + u8 sensor_location; + + if (hw->eeprom.ops.read(hw, ets_offset + 1 + i, &ets_sensor)) { + hw_err(hw, "eeprom read at offset %d failed\n", + ets_offset + 1 + i); + continue; + } + sensor_index = ((ets_sensor & IXGBE_ETS_DATA_INDEX_MASK) >> + IXGBE_ETS_DATA_INDEX_SHIFT); + sensor_location = ((ets_sensor & IXGBE_ETS_DATA_LOC_MASK) >> + IXGBE_ETS_DATA_LOC_SHIFT); + therm_limit = ets_sensor & IXGBE_ETS_DATA_HTHRESH_MASK; + + hw->phy.ops.write_i2c_byte(hw, + ixgbe_emc_therm_limit[sensor_index], + IXGBE_I2C_THERMAL_SENSOR_ADDR, therm_limit); + + if (sensor_location == 0) + continue; + + data->sensor[i].location = sensor_location; + data->sensor[i].caution_thresh = therm_limit; + data->sensor[i].max_op_thresh = therm_limit - low_thresh_delta; + } + + return 0; +} + +/** + * ixgbe_get_orom_version - Return option ROM from EEPROM + * + * @hw: pointer to hardware structure + * @nvm_ver: pointer to output structure + * + * if valid option ROM version, nvm_ver->or_valid set to true + * else nvm_ver->or_valid is false. + **/ +void ixgbe_get_orom_version(struct ixgbe_hw *hw, + struct ixgbe_nvm_version *nvm_ver) +{ + u16 offset, eeprom_cfg_blkh, eeprom_cfg_blkl; + + nvm_ver->or_valid = false; + /* Option Rom may or may not be present. Start with pointer */ + hw->eeprom.ops.read(hw, NVM_OROM_OFFSET, &offset); + + /* make sure offset is valid */ + if (offset == 0x0 || offset == NVM_INVALID_PTR) + return; + + hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_HI, &eeprom_cfg_blkh); + hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_LOW, &eeprom_cfg_blkl); + + /* option rom exists and is valid */ + if ((eeprom_cfg_blkl | eeprom_cfg_blkh) == 0x0 || + eeprom_cfg_blkl == NVM_VER_INVALID || + eeprom_cfg_blkh == NVM_VER_INVALID) + return; + + nvm_ver->or_valid = true; + nvm_ver->or_major = eeprom_cfg_blkl >> NVM_OROM_SHIFT; + nvm_ver->or_build = (eeprom_cfg_blkl << NVM_OROM_SHIFT) | + (eeprom_cfg_blkh >> NVM_OROM_SHIFT); + nvm_ver->or_patch = eeprom_cfg_blkh & NVM_OROM_PATCH_MASK; +} + +/** + * ixgbe_get_oem_prod_version - Etrack ID from EEPROM + * @hw: pointer to hardware structure + * @nvm_ver: pointer to output structure + * + * if valid OEM product version, nvm_ver->oem_valid set to true + * else nvm_ver->oem_valid is false. + **/ +void ixgbe_get_oem_prod_version(struct ixgbe_hw *hw, + struct ixgbe_nvm_version *nvm_ver) +{ + u16 rel_num, prod_ver, mod_len, cap, offset; + + nvm_ver->oem_valid = false; + hw->eeprom.ops.read(hw, NVM_OEM_PROD_VER_PTR, &offset); + + /* Return is offset to OEM Product Version block is invalid */ + if (offset == 0x0 || offset == NVM_INVALID_PTR) + return; + + /* Read product version block */ + hw->eeprom.ops.read(hw, offset, &mod_len); + hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_CAP_OFF, &cap); + + /* Return if OEM product version block is invalid */ + if (mod_len != NVM_OEM_PROD_VER_MOD_LEN || + (cap & NVM_OEM_PROD_VER_CAP_MASK) != 0x0) + return; + + hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_L, &prod_ver); + hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_H, &rel_num); + + /* Return if version is invalid */ + if ((rel_num | prod_ver) == 0x0 || + rel_num == NVM_VER_INVALID || prod_ver == NVM_VER_INVALID) + return; + + nvm_ver->oem_major = prod_ver >> NVM_VER_SHIFT; + nvm_ver->oem_minor = prod_ver & NVM_VER_MASK; + nvm_ver->oem_release = rel_num; + nvm_ver->oem_valid = true; +} + +/** + * ixgbe_get_etk_id - Return Etrack ID from EEPROM + * + * @hw: pointer to hardware structure + * @nvm_ver: pointer to output structure + * + * word read errors will return 0xFFFF + **/ +void ixgbe_get_etk_id(struct ixgbe_hw *hw, + struct ixgbe_nvm_version *nvm_ver) +{ + u16 etk_id_l, etk_id_h; + + if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_LOW, &etk_id_l)) + etk_id_l = NVM_VER_INVALID; + if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_HI, &etk_id_h)) + etk_id_h = NVM_VER_INVALID; + + /* The word order for the version format is determined by high order + * word bit 15. + */ + if ((etk_id_h & NVM_ETK_VALID) == 0) { + nvm_ver->etk_id = etk_id_h; + nvm_ver->etk_id |= (etk_id_l << NVM_ETK_SHIFT); + } else { + nvm_ver->etk_id = etk_id_l; + nvm_ver->etk_id |= (etk_id_h << NVM_ETK_SHIFT); + } +} + +void ixgbe_disable_rx_generic(struct ixgbe_hw *hw) +{ + u32 rxctrl; + + rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); + if (rxctrl & IXGBE_RXCTRL_RXEN) { + if (hw->mac.type != ixgbe_mac_82598EB) { + u32 pfdtxgswc; + + pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); + if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) { + pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN; + IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); + hw->mac.set_lben = true; + } else { + hw->mac.set_lben = false; + } + } + rxctrl &= ~IXGBE_RXCTRL_RXEN; + IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl); + } +} + +void ixgbe_enable_rx_generic(struct ixgbe_hw *hw) +{ + u32 rxctrl; + + rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); + IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN)); + + if (hw->mac.type != ixgbe_mac_82598EB) { + if (hw->mac.set_lben) { + u32 pfdtxgswc; + + pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); + pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN; + IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); + hw->mac.set_lben = false; + } + } +} + +/** ixgbe_mng_present - returns true when management capability is present + * @hw: pointer to hardware structure + **/ +bool ixgbe_mng_present(struct ixgbe_hw *hw) +{ + u32 fwsm; + + if (hw->mac.type < ixgbe_mac_82599EB) + return false; + + fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw)); + + return !!(fwsm & IXGBE_FWSM_FW_MODE_PT); +} + +/** + * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait_to_complete: true when waiting for completion is needed + * + * Set the link speed in the MAC and/or PHY register and restarts link. + */ +s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg_wait_to_complete) +{ + ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; + ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; + s32 status = 0; + u32 speedcnt = 0; + u32 i = 0; + bool autoneg, link_up = false; + + /* Mask off requested but non-supported speeds */ + status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg); + if (status) + return status; + + speed &= link_speed; + + /* Try each speed one by one, highest priority first. We do this in + * software because 10Gb fiber doesn't support speed autonegotiation. + */ + if (speed & IXGBE_LINK_SPEED_10GB_FULL) { + speedcnt++; + highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; + + /* Set the module link speed */ + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + hw->mac.ops.set_rate_select_speed(hw, + IXGBE_LINK_SPEED_10GB_FULL); + break; + case ixgbe_media_type_fiber_qsfp: + /* QSFP module automatically detects MAC link speed */ + break; + default: + hw_dbg(hw, "Unexpected media type\n"); + break; + } + + /* Allow module to change analog characteristics (1G->10G) */ + msleep(40); + + status = hw->mac.ops.setup_mac_link(hw, + IXGBE_LINK_SPEED_10GB_FULL, + autoneg_wait_to_complete); + if (status) + return status; + + /* Flap the Tx laser if it has not already been done */ + if (hw->mac.ops.flap_tx_laser) + hw->mac.ops.flap_tx_laser(hw); + + /* Wait for the controller to acquire link. Per IEEE 802.3ap, + * Section 73.10.2, we may have to wait up to 500ms if KR is + * attempted. 82599 uses the same timing for 10g SFI. + */ + for (i = 0; i < 5; i++) { + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, + &link_up, false); + if (status) + return status; + + if (link_up) + goto out; + } + } + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) { + speedcnt++; + if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) + highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; + + /* Set the module link speed */ + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + hw->mac.ops.set_rate_select_speed(hw, + IXGBE_LINK_SPEED_1GB_FULL); + break; + case ixgbe_media_type_fiber_qsfp: + /* QSFP module automatically detects link speed */ + break; + default: + hw_dbg(hw, "Unexpected media type\n"); + break; + } + + /* Allow module to change analog characteristics (10G->1G) */ + msleep(40); + + status = hw->mac.ops.setup_mac_link(hw, + IXGBE_LINK_SPEED_1GB_FULL, + autoneg_wait_to_complete); + if (status) + return status; + + /* Flap the Tx laser if it has not already been done */ + if (hw->mac.ops.flap_tx_laser) + hw->mac.ops.flap_tx_laser(hw); + + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_up) + goto out; + } + + /* We didn't get link. Configure back to the highest speed we tried, + * (if there was more than one). We call ourselves back with just the + * single highest speed that the user requested. + */ + if (speedcnt > 1) + status = ixgbe_setup_mac_link_multispeed_fiber(hw, + highest_link_speed, + autoneg_wait_to_complete); + +out: + /* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised = 0; + + if (speed & IXGBE_LINK_SPEED_10GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; + + return status; +} + +/** + * ixgbe_set_soft_rate_select_speed - Set module link speed + * @hw: pointer to hardware structure + * @speed: link speed to set + * + * Set module link speed via the soft rate select. + */ +void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw, + ixgbe_link_speed speed) +{ + s32 status; + u8 rs, eeprom_data; + + switch (speed) { + case IXGBE_LINK_SPEED_10GB_FULL: + /* one bit mask same as setting on */ + rs = IXGBE_SFF_SOFT_RS_SELECT_10G; + break; + case IXGBE_LINK_SPEED_1GB_FULL: + rs = IXGBE_SFF_SOFT_RS_SELECT_1G; + break; + default: + hw_dbg(hw, "Invalid fixed module speed\n"); + return; + } + + /* Set RS0 */ + status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + &eeprom_data); + if (status) { + hw_dbg(hw, "Failed to read Rx Rate Select RS0\n"); + return; + } + + eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; + + status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + eeprom_data); + if (status) { + hw_dbg(hw, "Failed to write Rx Rate Select RS0\n"); + return; + } + + /* Set RS1 */ + status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + &eeprom_data); + if (status) { + hw_dbg(hw, "Failed to read Rx Rate Select RS1\n"); + return; + } + + eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; + + status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + eeprom_data); + if (status) { + hw_dbg(hw, "Failed to write Rx Rate Select RS1\n"); + return; + } +} |