Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 401 insertions, 0 deletions

diff --git a/drivers/thermal/intel/intel_pch_thermal.c b/drivers/thermal/intel/intel_pch_thermal.c
new file mode 100644
index 0000000000..b3905e34c5
--- /dev/null
+++ b/drivers/thermal/intel/intel_pch_thermal.c
@@ -0,0 +1,401 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* intel_pch_thermal.c - Intel PCH Thermal driver
+ *
+ * Copyright (c) 2015, Intel Corporation.
+ *
+ * Authors:
+ *     Tushar Dave <tushar.n.dave@intel.com>
+ */
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/pm.h>
+#include <linux/suspend.h>
+#include <linux/thermal.h>
+#include <linux/types.h>
+#include <linux/units.h>
+
+/* Intel PCH thermal Device IDs */
+#define PCH_THERMAL_DID_HSW_1	0x9C24 /* Haswell PCH */
+#define PCH_THERMAL_DID_HSW_2	0x8C24 /* Haswell PCH */
+#define PCH_THERMAL_DID_WPT	0x9CA4 /* Wildcat Point */
+#define PCH_THERMAL_DID_SKL	0x9D31 /* Skylake PCH */
+#define PCH_THERMAL_DID_SKL_H	0xA131 /* Skylake PCH 100 series */
+#define PCH_THERMAL_DID_CNL	0x9Df9 /* CNL PCH */
+#define PCH_THERMAL_DID_CNL_H	0xA379 /* CNL-H PCH */
+#define PCH_THERMAL_DID_CNL_LP	0x02F9 /* CNL-LP PCH */
+#define PCH_THERMAL_DID_CML_H	0X06F9 /* CML-H PCH */
+#define PCH_THERMAL_DID_LWB	0xA1B1 /* Lewisburg PCH */
+#define PCH_THERMAL_DID_WBG	0x8D24 /* Wellsburg PCH */
+
+/* Wildcat Point-LP  PCH Thermal registers */
+#define WPT_TEMP	0x0000	/* Temperature */
+#define WPT_TSC	0x04	/* Thermal Sensor Control */
+#define WPT_TSS	0x06	/* Thermal Sensor Status */
+#define WPT_TSEL	0x08	/* Thermal Sensor Enable and Lock */
+#define WPT_TSREL	0x0A	/* Thermal Sensor Report Enable and Lock */
+#define WPT_TSMIC	0x0C	/* Thermal Sensor SMI Control */
+#define WPT_CTT	0x0010	/* Catastrophic Trip Point */
+#define WPT_TSPM	0x001C	/* Thermal Sensor Power Management */
+#define WPT_TAHV	0x0014	/* Thermal Alert High Value */
+#define WPT_TALV	0x0018	/* Thermal Alert Low Value */
+#define WPT_TL		0x00000040	/* Throttle Value */
+#define WPT_PHL	0x0060	/* PCH Hot Level */
+#define WPT_PHLC	0x62	/* PHL Control */
+#define WPT_TAS	0x80	/* Thermal Alert Status */
+#define WPT_TSPIEN	0x82	/* PCI Interrupt Event Enables */
+#define WPT_TSGPEN	0x84	/* General Purpose Event Enables */
+
+/*  Wildcat Point-LP  PCH Thermal Register bit definitions */
+#define WPT_TEMP_TSR	0x01ff	/* Temp TS Reading */
+#define WPT_TSC_CPDE	0x01	/* Catastrophic Power-Down Enable */
+#define WPT_TSS_TSDSS	0x10	/* Thermal Sensor Dynamic Shutdown Status */
+#define WPT_TSS_GPES	0x08	/* GPE status */
+#define WPT_TSEL_ETS	0x01    /* Enable TS */
+#define WPT_TSEL_PLDB	0x80	/* TSEL Policy Lock-Down Bit */
+#define WPT_TL_TOL	0x000001FF	/* T0 Level */
+#define WPT_TL_T1L	0x1ff00000	/* T1 Level */
+#define WPT_TL_TTEN	0x20000000	/* TT Enable */
+
+/* Resolution of 1/2 degree C and an offset of -50C */
+#define PCH_TEMP_OFFSET	(-50)
+#define GET_WPT_TEMP(x)	((x) * MILLIDEGREE_PER_DEGREE / 2 + WPT_TEMP_OFFSET)
+#define WPT_TEMP_OFFSET	(PCH_TEMP_OFFSET * MILLIDEGREE_PER_DEGREE)
+#define GET_PCH_TEMP(x)	(((x) / 2) + PCH_TEMP_OFFSET)
+
+#define PCH_MAX_TRIPS 3 /* critical, hot, passive */
+
+/* Amount of time for each cooling delay, 100ms by default for now */
+static unsigned int delay_timeout = 100;
+module_param(delay_timeout, int, 0644);
+MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration.");
+
+/* Number of iterations for cooling delay, 600 counts by default for now */
+static unsigned int delay_cnt = 600;
+module_param(delay_cnt, int, 0644);
+MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay.");
+
+static char driver_name[] = "Intel PCH thermal driver";
+
+struct pch_thermal_device {
+	void __iomem *hw_base;
+	struct pci_dev *pdev;
+	struct thermal_zone_device *tzd;
+	struct thermal_trip trips[PCH_MAX_TRIPS];
+	bool bios_enabled;
+};
+
+#ifdef CONFIG_ACPI
+/*
+ * On some platforms, there is a companion ACPI device, which adds
+ * passive trip temperature using _PSV method. There is no specific
+ * passive temperature setting in MMIO interface of this PCI device.
+ */
+static int pch_wpt_add_acpi_psv_trip(struct pch_thermal_device *ptd, int trip)
+{
+	struct acpi_device *adev;
+	int temp;
+
+	adev = ACPI_COMPANION(&ptd->pdev->dev);
+	if (!adev)
+		return 0;
+
+	if (thermal_acpi_passive_trip_temp(adev, &temp) || temp <= 0)
+		return 0;
+
+	ptd->trips[trip].type = THERMAL_TRIP_PASSIVE;
+	ptd->trips[trip].temperature = temp;
+	return 1;
+}
+#else
+static int pch_wpt_add_acpi_psv_trip(struct pch_thermal_device *ptd, int trip)
+{
+	return 0;
+}
+#endif
+
+static int pch_thermal_get_temp(struct thermal_zone_device *tzd, int *temp)
+{
+	struct pch_thermal_device *ptd = thermal_zone_device_priv(tzd);
+
+	*temp = GET_WPT_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP));
+	return 0;
+}
+
+static void pch_critical(struct thermal_zone_device *tzd)
+{
+	dev_dbg(thermal_zone_device(tzd), "%s: critical temperature reached\n",
+		thermal_zone_device_type(tzd));
+}
+
+static struct thermal_zone_device_ops tzd_ops = {
+	.get_temp = pch_thermal_get_temp,
+	.critical = pch_critical,
+};
+
+enum pch_board_ids {
+	PCH_BOARD_HSW = 0,
+	PCH_BOARD_WPT,
+	PCH_BOARD_SKL,
+	PCH_BOARD_CNL,
+	PCH_BOARD_CML,
+	PCH_BOARD_LWB,
+	PCH_BOARD_WBG,
+};
+
+static const char *board_names[] = {
+	[PCH_BOARD_HSW] = "pch_haswell",
+	[PCH_BOARD_WPT] = "pch_wildcat_point",
+	[PCH_BOARD_SKL] = "pch_skylake",
+	[PCH_BOARD_CNL] = "pch_cannonlake",
+	[PCH_BOARD_CML] = "pch_cometlake",
+	[PCH_BOARD_LWB] = "pch_lewisburg",
+	[PCH_BOARD_WBG] = "pch_wellsburg",
+};
+
+static int intel_pch_thermal_probe(struct pci_dev *pdev,
+				   const struct pci_device_id *id)
+{
+	enum pch_board_ids board_id = id->driver_data;
+	struct pch_thermal_device *ptd;
+	int nr_trips = 0;
+	u16 trip_temp;
+	u8 tsel;
+	int err;
+
+	ptd = devm_kzalloc(&pdev->dev, sizeof(*ptd), GFP_KERNEL);
+	if (!ptd)
+		return -ENOMEM;
+
+	pci_set_drvdata(pdev, ptd);
+	ptd->pdev = pdev;
+
+	err = pci_enable_device(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "failed to enable pci device\n");
+		return err;
+	}
+
+	err = pci_request_regions(pdev, driver_name);
+	if (err) {
+		dev_err(&pdev->dev, "failed to request pci region\n");
+		goto error_disable;
+	}
+
+	ptd->hw_base = pci_ioremap_bar(pdev, 0);
+	if (!ptd->hw_base) {
+		err = -ENOMEM;
+		dev_err(&pdev->dev, "failed to map mem base\n");
+		goto error_release;
+	}
+
+	/* Check if BIOS has already enabled thermal sensor */
+	if (WPT_TSEL_ETS & readb(ptd->hw_base + WPT_TSEL)) {
+		ptd->bios_enabled = true;
+		goto read_trips;
+	}
+
+	tsel = readb(ptd->hw_base + WPT_TSEL);
+	/*
+	 * When TSEL's Policy Lock-Down bit is 1, TSEL become RO.
+	 * If so, thermal sensor cannot enable. Bail out.
+	 */
+	if (tsel & WPT_TSEL_PLDB) {
+		dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n");
+		err = -ENODEV;
+		goto error_cleanup;
+	}
+
+	writeb(tsel|WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL);
+	if (!(WPT_TSEL_ETS & readb(ptd->hw_base + WPT_TSEL))) {
+		dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n");
+		err = -ENODEV;
+		goto error_cleanup;
+	}
+
+read_trips:
+	trip_temp = readw(ptd->hw_base + WPT_CTT);
+	trip_temp &= 0x1FF;
+	if (trip_temp) {
+		ptd->trips[nr_trips].temperature = GET_WPT_TEMP(trip_temp);
+		ptd->trips[nr_trips++].type = THERMAL_TRIP_CRITICAL;
+	}
+
+	trip_temp = readw(ptd->hw_base + WPT_PHL);
+	trip_temp &= 0x1FF;
+	if (trip_temp) {
+		ptd->trips[nr_trips].temperature = GET_WPT_TEMP(trip_temp);
+		ptd->trips[nr_trips++].type = THERMAL_TRIP_HOT;
+	}
+
+	nr_trips += pch_wpt_add_acpi_psv_trip(ptd, nr_trips);
+
+	ptd->tzd = thermal_zone_device_register_with_trips(board_names[board_id],
+							   ptd->trips, nr_trips,
+							   0, ptd, &tzd_ops,
+							   NULL, 0, 0);
+	if (IS_ERR(ptd->tzd)) {
+		dev_err(&pdev->dev, "Failed to register thermal zone %s\n",
+			board_names[board_id]);
+		err = PTR_ERR(ptd->tzd);
+		goto error_cleanup;
+	}
+	err = thermal_zone_device_enable(ptd->tzd);
+	if (err)
+		goto err_unregister;
+
+	return 0;
+
+err_unregister:
+	thermal_zone_device_unregister(ptd->tzd);
+error_cleanup:
+	iounmap(ptd->hw_base);
+error_release:
+	pci_release_regions(pdev);
+error_disable:
+	pci_disable_device(pdev);
+	dev_err(&pdev->dev, "pci device failed to probe\n");
+	return err;
+}
+
+static void intel_pch_thermal_remove(struct pci_dev *pdev)
+{
+	struct pch_thermal_device *ptd = pci_get_drvdata(pdev);
+
+	thermal_zone_device_unregister(ptd->tzd);
+	iounmap(ptd->hw_base);
+	pci_set_drvdata(pdev, NULL);
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+}
+
+static int intel_pch_thermal_suspend_noirq(struct device *device)
+{
+	struct pch_thermal_device *ptd = dev_get_drvdata(device);
+	u16 pch_thr_temp, pch_cur_temp;
+	int pch_delay_cnt = 0;
+	u8 tsel;
+
+	/* Shutdown the thermal sensor if it is not enabled by BIOS */
+	if (!ptd->bios_enabled) {
+		tsel = readb(ptd->hw_base + WPT_TSEL);
+		writeb(tsel & 0xFE, ptd->hw_base + WPT_TSEL);
+		return 0;
+	}
+
+	/* Do not check temperature if it is not s2idle */
+	if (pm_suspend_via_firmware())
+		return 0;
+
+	/* Get the PCH temperature threshold value */
+	pch_thr_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TSPM));
+
+	/* Get the PCH current temperature value */
+	pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP));
+
+	/*
+	 * If current PCH temperature is higher than configured PCH threshold
+	 * value, run some delay loop with sleep to let the current temperature
+	 * go down below the threshold value which helps to allow system enter
+	 * lower power S0ix suspend state. Even after delay loop if PCH current
+	 * temperature stays above threshold, notify the warning message
+	 * which helps to indentify the reason why S0ix entry was rejected.
+	 */
+	while (pch_delay_cnt < delay_cnt) {
+		if (pch_cur_temp < pch_thr_temp)
+			break;
+
+		if (pm_wakeup_pending()) {
+			dev_warn(&ptd->pdev->dev, "Wakeup event detected, abort cooling\n");
+			return 0;
+		}
+
+		pch_delay_cnt++;
+		dev_dbg(&ptd->pdev->dev,
+			"CPU-PCH current temp [%dC] higher than the threshold temp [%dC], sleep %d times for %d ms duration\n",
+			pch_cur_temp, pch_thr_temp, pch_delay_cnt, delay_timeout);
+		msleep(delay_timeout);
+		/* Read the PCH current temperature for next cycle. */
+		pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP));
+	}
+
+	if (pch_cur_temp >= pch_thr_temp)
+		dev_warn(&ptd->pdev->dev,
+			"CPU-PCH is hot [%dC] after %d ms delay. S0ix might fail\n",
+			pch_cur_temp, pch_delay_cnt * delay_timeout);
+	else {
+		if (pch_delay_cnt)
+			dev_info(&ptd->pdev->dev,
+				"CPU-PCH is cool [%dC] after %d ms delay\n",
+				pch_cur_temp, pch_delay_cnt * delay_timeout);
+		else
+			dev_info(&ptd->pdev->dev,
+				"CPU-PCH is cool [%dC]\n",
+				pch_cur_temp);
+	}
+
+	return 0;
+}
+
+static int intel_pch_thermal_resume(struct device *device)
+{
+	struct pch_thermal_device *ptd = dev_get_drvdata(device);
+	u8 tsel;
+
+	if (ptd->bios_enabled)
+		return 0;
+
+	tsel = readb(ptd->hw_base + WPT_TSEL);
+
+	writeb(tsel | WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL);
+
+	return 0;
+}
+
+static const struct pci_device_id intel_pch_thermal_id[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_HSW_1),
+		.driver_data = PCH_BOARD_HSW, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_HSW_2),
+		.driver_data = PCH_BOARD_HSW, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WPT),
+		.driver_data = PCH_BOARD_WPT, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL),
+		.driver_data = PCH_BOARD_SKL, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL_H),
+		.driver_data = PCH_BOARD_SKL, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL),
+		.driver_data = PCH_BOARD_CNL, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL_H),
+		.driver_data = PCH_BOARD_CNL, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL_LP),
+		.driver_data = PCH_BOARD_CNL, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CML_H),
+		.driver_data = PCH_BOARD_CML, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_LWB),
+		.driver_data = PCH_BOARD_LWB, },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WBG),
+		.driver_data = PCH_BOARD_WBG, },
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id);
+
+static const struct dev_pm_ops intel_pch_pm_ops = {
+	.suspend_noirq = intel_pch_thermal_suspend_noirq,
+	.resume = intel_pch_thermal_resume,
+};
+
+static struct pci_driver intel_pch_thermal_driver = {
+	.name		= "intel_pch_thermal",
+	.id_table	= intel_pch_thermal_id,
+	.probe		= intel_pch_thermal_probe,
+	.remove		= intel_pch_thermal_remove,
+	.driver.pm	= &intel_pch_pm_ops,
+};
+
+module_pci_driver(intel_pch_thermal_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Intel PCH Thermal driver");