diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/xilinx')
5 files changed, 403 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt new file mode 100644 index 000000000..d0335ca0c --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -0,0 +1,35 @@ +DT bindings for Xilinx video IP cores +------------------------------------- + +Xilinx video IP cores process video streams by acting as video sinks and/or +sources. They are connected by links through their input and output ports, +creating a video pipeline. + +Each video IP core is represented by an AMBA bus child node in the device +tree using bindings documented in this directory. Connections between the IP +cores are represented as defined in ../video-interfaces.txt. + +The whole pipeline is represented by an AMBA bus child node in the device +tree using bindings documented in ./xlnx,video.txt. + +Common properties +----------------- + +The following properties are common to all Xilinx video IP cores. + +- xlnx,video-format: This property represents a video format transmitted on an + AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream + Video IP and System Design Guide" [UG934]. How the format relates to the IP + core is described in the IP core bindings documentation. + +- xlnx,video-width: This property qualifies the video format with the sample + width expressed as a number of bits per pixel component. All components must + use the same width. + +- xlnx,cfa-pattern: When the video format is set to Mono/Sensor, this property + describes the sensor's color filter array pattern. Supported values are + "bggr", "gbrg", "grbg", "rggb" and "mono". If not specified, the pattern + defaults to "mono". + + +[UG934] https://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml new file mode 100644 index 000000000..43daf837f --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml @@ -0,0 +1,209 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/xilinx/xlnx,csi2rxss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx MIPI CSI-2 Receiver Subsystem + +maintainers: + - Vishal Sagar <vishal.sagar@amd.com> + +description: | + The Xilinx MIPI CSI-2 Receiver Subsystem is used to capture MIPI CSI-2 + traffic from compliant camera sensors and send the output as AXI4 Stream + video data for image processing. + The subsystem consists of a MIPI D-PHY in slave mode which captures the + data packets. This is passed along the MIPI CSI-2 Rx IP which extracts the + packet data. The optional Video Format Bridge (VFB) converts this data to + AXI4 Stream video data. + For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem. + Please note that this bindings includes only the MIPI CSI-2 Rx controller + and Video Format Bridge and not D-PHY. + +properties: + compatible: + items: + - enum: + - xlnx,mipi-csi2-rx-subsystem-5.0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: List of clock specifiers + items: + - description: AXI Lite clock + - description: Video clock + + clock-names: + items: + - const: lite_aclk + - const: video_aclk + + xlnx,csi-pxl-format: + description: | + This denotes the CSI Data type selected in hw design. + Packets other than this data type (except for RAW8 and + User defined data types) will be filtered out. + Possible values are as below - + 0x1e - YUV4228B + 0x1f - YUV42210B + 0x20 - RGB444 + 0x21 - RGB555 + 0x22 - RGB565 + 0x23 - RGB666 + 0x24 - RGB888 + 0x28 - RAW6 + 0x29 - RAW7 + 0x2a - RAW8 + 0x2b - RAW10 + 0x2c - RAW12 + 0x2d - RAW14 + 0x2e - RAW16 + 0x2f - RAW20 + $ref: /schemas/types.yaml#/definitions/uint32 + oneOf: + - minimum: 0x1e + maximum: 0x24 + - minimum: 0x28 + maximum: 0x2f + + xlnx,vfb: + type: boolean + description: Present when Video Format Bridge is enabled in IP configuration + + xlnx,en-csi-v2-0: + type: boolean + description: Present if CSI v2 is enabled in IP configuration. + + xlnx,en-vcx: + type: boolean + description: | + When present, there are maximum 16 virtual channels, else only 4. + + xlnx,en-active-lanes: + type: boolean + description: | + Present if the number of active lanes can be re-configured at + runtime in the Protocol Configuration Register. Otherwise all lanes, + as set in IP configuration, are always active. + + video-reset-gpios: + description: Optional specifier for a GPIO that asserts video_aresetn. + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + description: | + Input / sink port node, single endpoint describing the + CSI-2 transmitter. + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: | + This is required only in the sink port 0 endpoint which + connects to MIPI CSI-2 source like sensor. + The possible values are - + 1 - For 1 lane enabled in IP. + 1 2 - For 2 lanes enabled in IP. + 1 2 3 - For 3 lanes enabled in IP. + 1 2 3 4 - For 4 lanes enabled in IP. + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + required: + - data-lanes + + unevaluatedProperties: false + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: | + Output / source port node, endpoint describing modules + connected the CSI-2 receiver. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - ports + +allOf: + - if: + required: + - xlnx,vfb + then: + required: + - xlnx,csi-pxl-format + else: + properties: + xlnx,csi-pxl-format: false + + - if: + not: + required: + - xlnx,en-csi-v2-0 + then: + properties: + xlnx,en-vcx: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + xcsi2rxss_1: csi2rx@a0020000 { + compatible = "xlnx,mipi-csi2-rx-subsystem-5.0"; + reg = <0xa0020000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 95 4>; + xlnx,csi-pxl-format = <0x2a>; + xlnx,vfb; + xlnx,en-active-lanes; + xlnx,en-csi-v2-0; + xlnx,en-vcx; + clock-names = "lite_aclk", "video_aclk"; + clocks = <&misc_clk_0>, <&misc_clk_1>; + video-reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + /* Sink port */ + reg = <0>; + csiss_in: endpoint { + data-lanes = <1 2 3 4>; + /* MIPI CSI-2 Camera handle */ + remote-endpoint = <&camera_out>; + }; + }; + port@1 { + /* Source port */ + reg = <1>; + csiss_out: endpoint { + remote-endpoint = <&vproc_in>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt new file mode 100644 index 000000000..2aed3b4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt @@ -0,0 +1,33 @@ +Xilinx Video Timing Controller (VTC) +------------------------------------ + +The Video Timing Controller is a general purpose video timing generator and +detector. + +Required properties: + + - compatible: Must be "xlnx,v-tc-6.1". + + - reg: Physical base address and length of the registers set for the device. + + - clocks: Must contain a clock specifier for the VTC core and timing + interfaces clock. + +Optional properties: + + - xlnx,detector: The VTC has a timing detector + - xlnx,generator: The VTC has a timing generator + + At least one of the xlnx,detector and xlnx,generator properties must be + specified. + + +Example: + + vtc: vtc@43c40000 { + compatible = "xlnx,v-tc-6.1"; + reg = <0x43c40000 0x10000>; + + clocks = <&clkc 15>; + xlnx,generator; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt new file mode 100644 index 000000000..439351ab2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt @@ -0,0 +1,71 @@ +Xilinx Video Test Pattern Generator (TPG) +----------------------------------------- + +Required properties: + +- compatible: Must contain at least one of + + "xlnx,v-tpg-5.0" (TPG version 5.0) + "xlnx,v-tpg-6.0" (TPG version 6.0) + + TPG versions backward-compatible with previous versions should list all + compatible versions in the newer to older order. + +- reg: Physical base address and length of the registers set for the device. + +- clocks: Reference to the video core clock. + +- xlnx,video-format, xlnx,video-width: Video format and width, as defined in + video.txt. + +- port: Video port, using the DT bindings defined in ../video-interfaces.txt. + The TPG has a single output port numbered 0. + +Optional properties: + +- xlnx,vtc: A phandle referencing the Video Timing Controller that generates + video timings for the TPG test patterns. + +- timing-gpios: Specifier for a GPIO that controls the timing mux at the TPG + input. The GPIO active level corresponds to the selection of VTC-generated + video timings. + +The xlnx,vtc and timing-gpios properties are mandatory when the TPG is +synthesized with two ports and forbidden when synthesized with one port. + +Example: + + tpg_0: tpg@40050000 { + compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0"; + reg = <0x40050000 0x10000>; + clocks = <&clkc 15>; + + xlnx,vtc = <&vtc_3>; + timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg_in: endpoint { + remote-endpoint = <&adv7611_out>; + }; + }; + port@1 { + reg = <1>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg1_out: endpoint { + remote-endpoint = <&switch_in0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt new file mode 100644 index 000000000..5a0227023 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt @@ -0,0 +1,55 @@ +Xilinx Video IP Pipeline (VIPP) +------------------------------- + +General concept +--------------- + +Xilinx video IP pipeline processes video streams through one or more Xilinx +video IP cores. Each video IP core is represented as documented in video.txt +and IP core specific documentation, xlnx,v-*.txt, in this directory. The DT +node of the VIPP represents as a top level node of the pipeline and defines +mappings between DMAs and the video IP cores. + +Required properties: + +- compatible: Must be "xlnx,video". + +- dmas, dma-names: List of one DMA specifier and identifier string (as defined + in Documentation/devicetree/bindings/dma/dma.txt) per port. Each port + requires a DMA channel with the identifier string set to "port" followed by + the port index. + +- ports: Video port, using the DT bindings defined in ../video-interfaces.txt. + +Required port properties: + +- direction: should be either "input" or "output" depending on the direction + of stream. + +Example: + + video_cap { + compatible = "xlnx,video"; + dmas = <&vdma_1 1>, <&vdma_3 1>; + dma-names = "port0", "port1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + direction = "input"; + vcap0_in0: endpoint { + remote-endpoint = <&scaler0_out>; + }; + }; + port@1 { + reg = <1>; + direction = "input"; + vcap0_in1: endpoint { + remote-endpoint = <&switch_out1>; + }; + }; + }; + }; |