summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/vf610-nfc.txt')
-rw-r--r--Documentation/devicetree/bindings/mtd/vf610-nfc.txt59
1 files changed, 59 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
new file mode 100644
index 000000000..7db5e6e60
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
@@ -0,0 +1,59 @@
+Freescale's NAND flash controller (NFC)
+
+This variant of the Freescale NAND flash controller (NFC) can be found on
+Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70.
+
+Required properties:
+- compatible: Should be set to "fsl,vf610-nfc".
+- reg: address range of the NFC.
+- interrupts: interrupt of the NFC.
+- #address-cells: shall be set to 1. Encode the nand CS.
+- #size-cells : shall be set to 0.
+- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
+- assigned-clock-rates: The NAND bus timing is derived from this clock
+ rate and should not exceed maximum timing for any NAND memory chip
+ in a board stuffing. Typical NAND memory timings derived from this
+ clock are found in the SoC hardware reference manual. Furthermore,
+ there might be restrictions on maximum rates when using hardware ECC.
+
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+ representing partitions.
+
+Required children nodes:
+Children nodes represent the available nand chips. Currently the driver can
+only handle one NAND chip.
+
+Required properties:
+- compatible: Should be set to "fsl,vf610-nfc-cs".
+- nand-bus-width: see nand-controller.yaml
+- nand-ecc-mode: see nand-controller.yaml
+
+Required properties for hardware ECC:
+- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand-controller.yaml)
+- nand-ecc-step-size: step size equals page size, currently only 2k pages are
+ supported
+- nand-on-flash-bbt: see nand-controller.yaml
+
+Example:
+
+ nfc: nand@400e0000 {
+ compatible = "fsl,vf610-nfc";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x400e0000 0x4000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks VF610_CLK_NFC>;
+ clock-names = "nfc";
+ assigned-clocks = <&clks VF610_CLK_NFC>;
+ assigned-clock-rates = <33000000>;
+
+ nand@0 {
+ compatible = "fsl,vf610-nfc-nandcs";
+ reg = <0>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <32>;
+ nand-ecc-step-size = <2048>;
+ nand-on-flash-bbt;
+ };
+ };