diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa')
20 files changed, 3902 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt new file mode 100644 index 0000000000..f824fdae0d --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt @@ -0,0 +1,147 @@ +Atheros AR9331 built-in switch +============================= + +It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal +MDIO bus. All PHYs are built-in as well. + +Required properties: + + - compatible: should be: "qca,ar9331-switch" + - reg: Address on the MII bus for the switch. + - resets : Must contain an entry for each entry in reset-names. + - reset-names : Must include the following entries: "switch" + - interrupt-parent: Phandle to the parent interrupt controller + - interrupts: IRQ line for the switch + - interrupt-controller: Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. + - #interrupt-cells: must be 1 + - mdio: Container of PHY and devices on the switches MDIO bus. + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required and optional properties. +Examples: + +eth0: ethernet@19000000 { + compatible = "qca,ar9330-eth"; + reg = <0x19000000 0x200>; + interrupts = <4>; + + resets = <&rst 9>, <&rst 22>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; + clock-names = "eth", "mdio"; + + phy-mode = "mii"; + phy-handle = <&phy_port4>; +}; + +eth1: ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch10: switch@10 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "qca,ar9331-switch"; + reg = <0x10>; + resets = <&rst 8>; + reset-names = "switch"; + + interrupt-parent = <&miscintc>; + interrupts = <12>; + + interrupt-controller; + #interrupt-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch_port0: port@0 { + reg = <0x0>; + ethernet = <ð1>; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch_port1: port@1 { + reg = <0x1>; + phy-handle = <&phy_port0>; + phy-mode = "internal"; + }; + + switch_port2: port@2 { + reg = <0x2>; + phy-handle = <&phy_port1>; + phy-mode = "internal"; + }; + + switch_port3: port@3 { + reg = <0x3>; + phy-handle = <&phy_port2>; + phy-mode = "internal"; + }; + + switch_port4: port@4 { + reg = <0x4>; + phy-handle = <&phy_port3>; + phy-mode = "internal"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&switch10>; + + phy_port0: phy@0 { + reg = <0x0>; + interrupts = <0>; + }; + + phy_port1: phy@1 { + reg = <0x1>; + interrupts = <0>; + }; + + phy_port2: phy@2 { + reg = <0x2>; + interrupts = <0>; + }; + + phy_port3: phy@3 { + reg = <0x3>; + interrupts = <0>; + }; + + phy_port4: phy@4 { + reg = <0x4>; + interrupts = <0>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml b/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml new file mode 100644 index 0000000000..9565a74021 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/arrow,xrs700x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Arrow SpeedChips XRS7000 Series Switch + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +maintainers: + - George McCollister <george.mccollister@gmail.com> + +description: + The Arrow SpeedChips XRS7000 Series of single chip gigabit Ethernet switches + are designed for critical networking applications. They have up to three + RGMII ports and one RMII port and are managed via i2c or mdio. + +properties: + compatible: + oneOf: + - enum: + - arrow,xrs7003e + - arrow,xrs7003f + - arrow,xrs7004e + - arrow,xrs7004f + + reg: + maxItems: 1 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + switch@8 { + compatible = "arrow,xrs7004e"; + reg = <0x8>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + ethernet-port@1 { + reg = <1>; + label = "lan0"; + phy-handle = <&swphy0>; + phy-mode = "rgmii-id"; + }; + ethernet-port@2 { + reg = <2>; + label = "lan1"; + phy-handle = <&swphy1>; + phy-mode = "rgmii-id"; + }; + ethernet-port@3 { + reg = <3>; + ethernet = <&fec1>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml b/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml new file mode 100644 index 0000000000..4c78c54634 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml @@ -0,0 +1,268 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/brcm,b53.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM53xx Ethernet switches + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +description: + Broadcom BCM53xx Ethernet switches + +properties: + compatible: + oneOf: + - const: brcm,bcm5325 + - const: brcm,bcm53115 + - const: brcm,bcm53125 + - const: brcm,bcm53128 + - const: brcm,bcm53134 + - const: brcm,bcm5365 + - const: brcm,bcm5395 + - const: brcm,bcm5389 + - const: brcm,bcm5397 + - const: brcm,bcm5398 + - items: + - const: brcm,bcm11360-srab + - const: brcm,cygnus-srab + - items: + - enum: + - brcm,bcm53010-srab + - brcm,bcm53011-srab + - brcm,bcm53012-srab + - brcm,bcm53018-srab + - brcm,bcm53019-srab + - const: brcm,bcm5301x-srab + - items: + - enum: + - brcm,bcm11404-srab + - brcm,bcm11407-srab + - brcm,bcm11409-srab + - brcm,bcm58310-srab + - brcm,bcm58311-srab + - brcm,bcm58313-srab + - const: brcm,omega-srab + - items: + - enum: + - brcm,bcm58522-srab + - brcm,bcm58523-srab + - brcm,bcm58525-srab + - brcm,bcm58622-srab + - brcm,bcm58623-srab + - brcm,bcm58625-srab + - brcm,bcm88312-srab + - const: brcm,nsp-srab + - items: + - enum: + - brcm,bcm3384-switch + - brcm,bcm6318-switch + - brcm,bcm6328-switch + - brcm,bcm6362-switch + - brcm,bcm6368-switch + - brcm,bcm63268-switch + - const: brcm,bcm63xx-switch + +required: + - compatible + - reg + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - if: + properties: + compatible: + contains: + enum: + - brcm,bcm5325 + - brcm,bcm53115 + - brcm,bcm53125 + - brcm,bcm53128 + - brcm,bcm5365 + - brcm,bcm5395 + - brcm,bcm5397 + - brcm,bcm5398 + then: + $ref: /schemas/spi/spi-peripheral-props.yaml + + # BCM585xx/586xx/88312 SoCs + - if: + properties: + compatible: + contains: + enum: + - brcm,bcm58522-srab + - brcm,bcm58523-srab + - brcm,bcm58525-srab + - brcm,bcm58622-srab + - brcm,bcm58623-srab + - brcm,bcm58625-srab + - brcm,bcm88312-srab + then: + properties: + reg: + minItems: 3 + maxItems: 3 + reg-names: + items: + - const: srab + - const: mux_config + - const: sgmii_config + interrupts: + minItems: 13 + maxItems: 13 + interrupt-names: + items: + - const: link_state_p0 + - const: link_state_p1 + - const: link_state_p2 + - const: link_state_p3 + - const: link_state_p4 + - const: link_state_p5 + - const: link_state_p7 + - const: link_state_p8 + - const: phy + - const: ts + - const: imp_sleep_timer_p5 + - const: imp_sleep_timer_p7 + - const: imp_sleep_timer_p8 + required: + - interrupts + else: + properties: + reg: + maxItems: 1 + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@1e { + compatible = "brcm,bcm53125"; + reg = <30>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@5 { + reg = <5>; + label = "cable-modem"; + phy-mode = "rgmii-txid"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@8 { + reg = <8>; + phy-mode = "rgmii-txid"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + axi { + #address-cells = <1>; + #size-cells = <1>; + + switch@36000 { + compatible = "brcm,bcm58623-srab", "brcm,nsp-srab"; + reg = <0x36000 0x1000>, + <0x3f308 0x8>, + <0x3f410 0xc>; + reg-names = "srab", "mux_config", "sgmii_config"; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "link_state_p0", + "link_state_p1", + "link_state_p2", + "link_state_p3", + "link_state_p4", + "link_state_p5", + "link_state_p7", + "link_state_p8", + "phy", + "ts", + "imp_sleep_timer_p5", + "imp_sleep_timer_p7", + "imp_sleep_timer_p8"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + label = "port0"; + reg = <0>; + }; + + port@1 { + label = "port1"; + reg = <1>; + }; + + port@2 { + label = "port2"; + reg = <2>; + }; + + port@3 { + label = "port3"; + reg = <3>; + }; + + port@4 { + label = "port4"; + reg = <4>; + }; + + port@8 { + ethernet = <&amac2>; + reg = <8>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/brcm,sf2.yaml b/Documentation/devicetree/bindings/net/dsa/brcm,sf2.yaml new file mode 100644 index 0000000000..b06c416893 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/brcm,sf2.yaml @@ -0,0 +1,166 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/brcm,sf2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Starfighter 2 integrated switch + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +properties: + compatible: + items: + - enum: + - brcm,bcm4908-switch + - brcm,bcm7278-switch-v4.0 + - brcm,bcm7278-switch-v4.8 + - brcm,bcm7445-switch-v4.0 + + reg: + minItems: 6 + maxItems: 6 + + reg-names: + items: + - const: core + - const: reg + - const: intrl2_0 + - const: intrl2_1 + - const: fcb + - const: acb + + interrupts: + minItems: 2 + maxItems: 2 + + interrupt-names: + items: + - const: switch_0 + - const: switch_1 + + resets: + maxItems: 1 + + reset-names: + const: switch + + clocks: + minItems: 1 + items: + - description: switch's main clock + - description: dividing of the switch core clock + + clock-names: + minItems: 1 + items: + - const: sw_switch + - const: sw_switch_mdiv + + brcm,num-gphy: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum number of integrated gigabit PHYs in the switch + + brcm,num-rgmii-ports: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum number of RGMII interfaces supported by the switch + + brcm,fcb-pause-override: + description: if present indicates that the switch supports Failover Control + Block pause override capability + type: boolean + + brcm,acb-packets-inflight: + description: if present indicates that the switch Admission Control Block + supports reporting the number of packets in-flight in a switch queue + type: boolean + + ports: + type: object + + patternProperties: + '^port@[0-9a-f]$': + $ref: dsa-port.yaml# + unevaluatedProperties: false + + properties: + brcm,use-bcm-hdr: + description: if present, indicates that the switch port has Broadcom + tags enabled (per-packet metadata) + type: boolean + +required: + - reg + - interrupts + +allOf: + - $ref: dsa.yaml# + - if: + properties: + compatible: + contains: + enum: + - brcm,bcm7278-switch-v4.0 + - brcm,bcm7278-switch-v4.8 + then: + properties: + clocks: + minItems: 1 + maxItems: 1 + clock-names: + minItems: 1 + maxItems: 1 + required: + - clocks + - clock-names + - if: + properties: + compatible: + contains: + const: brcm,bcm7445-switch-v4.0 + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + minItems: 2 + maxItems: 2 + required: + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + switch@f0b00000 { + compatible = "brcm,bcm7445-switch-v4.0"; + reg = <0xf0b00000 0x40000>, + <0xf0b40000 0x110>, + <0xf0b40340 0x30>, + <0xf0b40380 0x30>, + <0xf0b40400 0x34>, + <0xf0b40600 0x208>; + reg-names = "core", "reg", "intrl2_0", "intrl2_1", + "fcb", "acb"; + interrupts = <0 0x18 0>, + <0 0x19 0>; + clocks = <&sw_switch>, <&sw_switch_mdiv>; + clock-names = "sw_switch", "sw_switch_mdiv"; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml new file mode 100644 index 0000000000..4801204699 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/dsa-port.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic DSA Switch Port + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> + +description: + A DSA switch port is a component of a switch that manages one MAC, and can + pass Ethernet frames. It can act as a stanadard Ethernet switch port, or have + DSA-specific functionality. + +$ref: /schemas/net/ethernet-switch-port.yaml# + +properties: + reg: + items: + - description: Port number + + label: + description: + Describes the label associated with this port, which will become + the netdev name + $ref: /schemas/types.yaml#/definitions/string + + link: + description: + Should be a list of phandles to other switch's DSA port. This + port is used as the outgoing port towards the phandle ports. The + full routing information must be given, not just the one hop + routes to neighbouring switches + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + maxItems: 1 + + ethernet: + description: + Should be a phandle to a valid Ethernet device node. This host + device is what the switch port is connected to + $ref: /schemas/types.yaml#/definitions/phandle + + dsa-tag-protocol: + description: + Instead of the default, the switch will use this tag protocol if + possible. Useful when a device supports multiple protocols and + the default is incompatible with the Ethernet device. + enum: + - dsa + - edsa + - ocelot + - ocelot-8021q + - rtl8_4 + - rtl8_4t + - seville + +# CPU and DSA ports must have phylink-compatible link descriptions +if: + oneOf: + - required: [ ethernet ] + - required: [ link ] +then: + allOf: + - required: + - phy-mode + - oneOf: + - required: + - fixed-link + - required: + - phy-handle + - required: + - managed + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt new file mode 100644 index 0000000000..dab208b5c7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -0,0 +1,4 @@ +Distributed Switch Architecture Device Tree Bindings +---------------------------------------------------- + +See Documentation/devicetree/bindings/net/dsa/dsa.yaml for the documentation. diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml new file mode 100644 index 0000000000..ec74a660be --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/dsa.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ethernet Switch + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> + +description: + This binding represents Ethernet Switches which have a dedicated CPU + port. That port is usually connected to an Ethernet Controller of the + SoC. Such setups are typical for embedded devices. + +select: false + +$ref: /schemas/net/ethernet-switch.yaml# + +properties: + dsa,member: + minItems: 2 + maxItems: 2 + description: + A two element list indicates which DSA cluster, and position within the + cluster a switch takes. <0 0> is cluster 0, switch 0. <0 1> is cluster 0, + switch 1. <1 0> is cluster 1, switch 0. A switch not part of any cluster + (single device hanging off a CPU port) must not specify this property + $ref: /schemas/types.yaml#/definitions/uint32-array + +additionalProperties: true + +$defs: + ethernet-ports: + description: A DSA switch without any extra port properties + $ref: '#' + + patternProperties: + "^(ethernet-)?ports$": + type: object + additionalProperties: false + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^(ethernet-)?port@[0-9]+$": + description: Ethernet switch ports + $ref: dsa-port.yaml# + unevaluatedProperties: false + +... diff --git a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml new file mode 100644 index 0000000000..4021b054f6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/hirschmann,hellcreek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hirschmann Hellcreek TSN Switch + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> + - Kurt Kanzenbach <kurt@linutronix.de> + +description: + The Hellcreek TSN Switch IP is a 802.1Q Ethernet compliant switch. It supports + the Precision Time Protocol, Hardware Timestamping as well the Time Aware + Shaper. + +properties: + compatible: + items: + - const: hirschmann,hellcreek-de1soc-r1 + + reg: + description: + The physical base address and size of TSN and PTP memory base + minItems: 2 + maxItems: 2 + + reg-names: + items: + - const: tsn + - const: ptp + + leds: + type: object + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^led@[01]$": + type: object + description: Hellcreek leds + $ref: /schemas/leds/common.yaml# + + properties: + reg: + items: + - enum: [0, 1] + description: Led number + + label: true + + default-state: true + + required: + - reg + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + - ethernet-ports + - leds + +unevaluatedProperties: false + +examples: + - | + switch0: switch@ff240000 { + compatible = "hirschmann,hellcreek-de1soc-r1"; + reg = <0xff240000 0x1000>, + <0xff250000 0x1000>; + reg-names = "tsn", "ptp"; + dsa,member = <0 0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ethernet = <&gmac0>; + phy-mode = "mii"; + + fixed-link { + speed = <100>; + full-duplex; + }; + }; + + port@2 { + reg = <2>; + label = "lan0"; + phy-handle = <&phy1>; + }; + + port@3 { + reg = <3>; + label = "lan1"; + phy-handle = <&phy2>; + }; + }; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + label = "sync_good"; + default-state = "on"; + }; + + led@1 { + reg = <1>; + label = "is_gm"; + default-state = "off"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt new file mode 100644 index 0000000000..46a732087f --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -0,0 +1,100 @@ +SMSC/MicroChip LAN9303 three port ethernet switch +------------------------------------------------- + +Required properties: + +- compatible: should be + - "smsc,lan9303-i2c" for I2C managed mode + or + - "smsc,lan9303-mdio" for mdio managed mode + +Optional properties: + +- reset-gpios: GPIO to be used to reset the whole device +- reset-duration: reset duration in milliseconds, defaults to 200 ms + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. The CPU port of this switch is always port 0. + +Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is +configured to use 1/2/3 instead. This hardware configuration will be +auto-detected and mapped accordingly. + +Example: + +I2C managed mode: + + master: masterdevice@X { + + fixed-link { /* RMII fixed link to LAN9303 */ + speed = <100>; + full-duplex; + }; + }; + + switch: switch@a { + compatible = "smsc,lan9303-i2c"; + reg = <0xa>; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <200>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { /* RMII fixed link to master */ + reg = <0>; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1"; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + +MDIO managed mode: + + master: masterdevice@X { + phy-handle = <&switch>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch: switch-phy@0 { + compatible = "smsc,lan9303-mdio"; + reg = <0>; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <100>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1"; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt new file mode 100644 index 0000000000..8bb1eff21c --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -0,0 +1,146 @@ +Lantiq GSWIP Ethernet switches +================================== + +Required properties for GSWIP core: + +- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the + xRX200 SoC + "lantiq,xrx300-gswip" for the embedded GSWIP in the + xRX300 SoC + "lantiq,xrx330-gswip" for the embedded GSWIP in the + xRX330 SoC +- reg : memory range of the GSWIP core registers + : memory range of the GSWIP MDIO registers + : memory range of the GSWIP MII registers + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of +additional required and optional properties. + + +Required properties for MDIO bus: +- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP + core of the xRX200 SoC and the PHYs connected to it. + +See Documentation/devicetree/bindings/net/mdio.txt for a list of additional +required and optional properties. + + +Required properties for GPHY firmware loading: +- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw" + for the loading of the firmware into the embedded + GPHY core of the SoC. +- lantiq,rcu : reference to the rcu syscon + +The GPHY firmware loader has a list of GPHY entries, one for each +embedded GPHY + +- reg : Offset of the GPHY firmware register in the RCU + register range +- resets : list of resets of the embedded GPHY +- reset-names : list of names of the resets + +Example: + +Ethernet switch on the VRX200 SoC: + +switch@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-gswip"; + reg = < 0xe108000 0x3100 /* switch */ + 0xe10b100 0xd8 /* mdio */ + 0xe10b1d8 0x130 /* mii */ + >; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + + port@4 { + reg = <4>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy13>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + + port@6 { + reg = <0x6>; + ethernet = <ð0>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + }; + }; + + gphy-fw { + compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"; + lantiq,rcu = <&rcu0>; + #address-cells = <1>; + #size-cells = <0>; + + gphy@20 { + reg = <0x20>; + + resets = <&reset0 31 30>; + reset-names = "gphy"; + }; + + gphy@68 { + reg = <0x68>; + + resets = <&reset0 29 28>; + reset-names = "gphy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt new file mode 100644 index 0000000000..6ec0c181b6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -0,0 +1,109 @@ +Marvell DSA Switch Device Tree Bindings +--------------------------------------- + +WARNING: This binding is currently unstable. Do not program it into a +FLASH never to be changed again. Once this binding is stable, this +warning will be removed. + +If you need a stable binding, use the old dsa.txt binding. + +Marvell Switches are MDIO devices. The following properties should be +placed as a child node of an mdio device. + +The properties described here are those specific to Marvell devices. +Additional required and optional properties can be found in dsa.txt. + +The compatibility string is used only to find an identification register, +which is at a different MDIO base address in different switch families. +- "marvell,mv88e6085" : Switch has base address 0x10. Use with models: + 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, + 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321, + 6341, 6350, 6351, 6352 +- "marvell,mv88e6190" : Switch has base address 0x00. Use with models: + 6190, 6190X, 6191, 6290, 6361, 6390, 6390X +- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: + 6220, 6250 + +Required properties: +- compatible : Should be one of "marvell,mv88e6085", + "marvell,mv88e6190" or "marvell,mv88e6250" as + indicated above +- reg : Address on the MII bus for the switch. + +Optional properties: + +- reset-gpios : Should be a gpio specifier for a reset line +- interrupts : Interrupt from the switch +- interrupt-controller : Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. +#interrupt-cells = <2> : Controller uses two cells, number and flag +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. +- mdio : Container of PHY and devices on the switches MDIO + bus. +- mdio? : Container of PHYs and devices on the external MDIO + bus. The node must contains a compatible string of + "marvell,mv88e6xxx-mdio-external" + +Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + switch0: switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + switch0: switch@0 { + compatible = "marvell,mv88e6190"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + mdio1 { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + switch1phy9: switch1phy0@9 { + reg = <9>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml new file mode 100644 index 0000000000..e532c6b795 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml @@ -0,0 +1,812 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT7530 and MT7531 Ethernet Switches + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Landen Chao <Landen.Chao@mediatek.com> + - DENG Qingfang <dqfext@gmail.com> + - Sean Wang <sean.wang@mediatek.com> + - Daniel Golle <daniel@makrotopia.org> + +description: | + There are three versions of MT7530, standalone, in a multi-chip module and + built-into a SoC. + + MT7530 is a part of the multi-chip module in MT7620AN, MT7620DA, MT7620DAN, + MT7620NN, MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs. + + The MT7988 SoC comes with a built-in switch similar to MT7531 as well as four + Gigabit Ethernet PHYs. The switch registers are directly mapped into the SoC's + memory map rather than using MDIO. The switch got an internally connected 10G + CPU port and 4 user ports connected to the built-in Gigabit Ethernet PHYs. + + MT7530 in MT7620AN, MT7620DA, MT7620DAN and MT7620NN SoCs has got 10/100 PHYs + and the switch registers are directly mapped into SoC's memory map rather than + using MDIO. The DSA driver currently doesn't support MT7620 variants. + + There is only the standalone version of MT7531. + + Port 5 on MT7530 has got various ways of configuration: + + - Port 5 can be used as a CPU port. + + - PHY 0 or 4 of the switch can be muxed to gmac5 of the switch. Therefore, + the gmac of the SoC which is wired to port 5 can connect to the PHY. + This is usually used for connecting the wan port directly to the CPU to + achieve 2 Gbps routing in total. + + The driver looks up the reg on the ethernet-phy node, which the phy-handle + property on the gmac node refers to, to mux the specified phy. + + The driver requires the gmac of the SoC to have "mediatek,eth-mac" as the + compatible string and the reg must be 1. So, for now, only gmac1 of a + MediaTek SoC can benefit this. Banana Pi BPI-R2 suits this. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + + Check out example 5. + + - For the multi-chip module MT7530, in case of an external phy wired to + gmac1 of the SoC, port 5 must not be enabled. + + In case of muxing PHY 0 or 4, the external phy must not be enabled. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + + Check out example 6. + + - Port 5 can be wired to an external phy. Port 5 becomes a DSA slave. + + For the multi-chip module MT7530, the external phy must be wired TX to TX + to gmac1 of the SoC for this to work. Ubiquiti EdgeRouter X SFP is wired + this way. + + For the multi-chip module MT7530, muxing PHY 0 or 4 won't work when the + external phy is connected TX to TX. + + For the MT7621 SoCs, rgmii2 group must be claimed with gpio function. + + Check out example 7. + +properties: + compatible: + oneOf: + - description: + Standalone MT7530 and multi-chip module MT7530 in MT7623AI SoC + const: mediatek,mt7530 + + - description: + Standalone MT7531 + const: mediatek,mt7531 + + - description: + Multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + const: mediatek,mt7621 + + - description: + Built-in switch of the MT7988 SoC + const: mediatek,mt7988-switch + + reg: + maxItems: 1 + + core-supply: + description: + Phandle to the regulator node necessary for the core power. + + "#gpio-cells": + const: 2 + + gpio-controller: + type: boolean + description: | + If defined, LED controller of the MT7530 switch will run on GPIO mode. + + There are 15 controllable pins. + port 0 LED 0..2 as GPIO 0..2 + port 1 LED 0..2 as GPIO 3..5 + port 2 LED 0..2 as GPIO 6..8 + port 3 LED 0..2 as GPIO 9..11 + port 4 LED 0..2 as GPIO 12..14 + + "#interrupt-cells": + const: 1 + + interrupt-controller: true + + interrupts: + maxItems: 1 + + io-supply: + description: | + Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for + details for the regulator setup on these boards. + + mediatek,mcm: + type: boolean + description: + Used for MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs which the MT7530 + switch is a part of the multi-chip module. + + reset-gpios: + description: | + GPIO to reset the switch. Use this if mediatek,mcm is not used. + This property is optional because some boards share the reset line with + other components which makes it impossible to probe the switch if the + reset line is used. + maxItems: 1 + + reset-names: + const: mcm + + resets: + description: + Phandle pointing to the system reset controller with line index for the + ethsys. + maxItems: 1 + +patternProperties: + "^(ethernet-)?ports$": + type: object + + patternProperties: + "^(ethernet-)?port@[0-9]+$": + type: object + + properties: + reg: + description: + Port address described must be 5 or 6 for CPU port and from 0 to 5 + for user ports. + + allOf: + - if: + required: [ ethernet ] + then: + properties: + reg: + enum: + - 5 + - 6 + +required: + - compatible + - reg + +$defs: + mt7530-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - gmii + - mii + - rgmii + else: + properties: + phy-mode: + enum: + - rgmii + - trgmii + + mt7531-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - rgmii + - sgmii + else: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - sgmii + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - if: + required: + - mediatek,mcm + then: + properties: + reset-gpios: false + + required: + - resets + - reset-names + + - dependencies: + interrupt-controller: [ interrupts ] + + - if: + properties: + compatible: + const: mediatek,mt7530 + then: + $ref: "#/$defs/mt7530-dsa-port" + required: + - core-supply + - io-supply + + - if: + properties: + compatible: + const: mediatek,mt7531 + then: + $ref: "#/$defs/mt7531-dsa-port" + properties: + gpio-controller: false + mediatek,mcm: false + + - if: + properties: + compatible: + const: mediatek,mt7621 + then: + $ref: "#/$defs/mt7530-dsa-port" + required: + - mediatek,mcm + + - if: + properties: + compatible: + const: mediatek,mt7988-switch + then: + $ref: "#/$defs/mt7530-dsa-port" + properties: + gpio-controller: false + mediatek,mcm: false + reset-names: false + +unevaluatedProperties: false + +examples: + # Example 1: Standalone MT7530 + - | + #include <dt-bindings/gpio/gpio.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7530"; + reg = <0x1f>; + + reset-gpios = <&pio 33 0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 2: MT7530 in MT7623AI SoC + - | + #include <dt-bindings/reset/mt2701-resets.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7530"; + reg = <0x1f>; + + mediatek,mcm; + resets = <ðsys MT2701_ETHSYS_MCM_RST>; + reset-names = "mcm"; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 3: Standalone MT7531 + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7531"; + reg = <0>; + + reset-gpios = <&pio 54 0>; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 4: MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 5: MT7621: mux MT7530's phy4 to SoC's gmac1 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + + phy-mode = "rgmii"; + phy-handle = <&example5_ethphy4>; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* MT7530's phy4 */ + example5_ethphy4: ethernet-phy@4 { + reg = <4>; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + /* Commented out, phy4 is connected to gmac1. + port@4 { + reg = <4>; + label = "wan"; + }; + */ + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; + + # Example 6: MT7621: mux external phy to SoC's gmac1 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + + phy-mode = "rgmii"; + phy-handle = <&example6_ethphy7>; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* External PHY */ + example6_ethphy7: ethernet-phy@7 { + reg = <7>; + phy-mode = "rgmii"; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; + + # Example 7: MT7621: mux external phy to MT7530's port 5 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* External PHY */ + example7_ethphy7: ethernet-phy@7 { + reg = <7>; + phy-mode = "rgmii"; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@5 { + reg = <5>; + label = "extphy"; + phy-mode = "rgmii-txid"; + phy-handle = <&example7_ethphy7>; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml new file mode 100644 index 0000000000..03b5567be3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml @@ -0,0 +1,162 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/microchip,ksz.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip KSZ Series Ethernet switches + +maintainers: + - Marek Vasut <marex@denx.de> + - Woojung Huh <Woojung.Huh@microchip.com> + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + # See Documentation/devicetree/bindings/net/dsa/dsa.yaml for a list of additional + # required and optional properties. + compatible: + enum: + - microchip,ksz8765 + - microchip,ksz8794 + - microchip,ksz8795 + - microchip,ksz8863 + - microchip,ksz8873 + - microchip,ksz9477 + - microchip,ksz9897 + - microchip,ksz9896 + - microchip,ksz9567 + - microchip,ksz8565 + - microchip,ksz9893 + - microchip,ksz9563 + - microchip,ksz8563 + + reset-gpios: + description: + Should be a gpio specifier for a reset line. + maxItems: 1 + + microchip,synclko-125: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set if the output SYNCLKO frequency should be set to 125MHz instead of 25MHz. + + microchip,synclko-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set if the output SYNCLKO clock should be disabled. Do not mix with + microchip,synclko-125. + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + // Ethernet switch connected via SPI to the host, CPU port wired to eth0: + eth0 { + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + spi { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&pinctrl_spi_ksz>; + cs-gpios = <&pioC 25 0>; + id = <1>; + + ksz9477: switch@0 { + compatible = "microchip,ksz9477"; + reg = <0>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + + spi-max-frequency = <44000000>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { + reg = <4>; + label = "lan5"; + }; + port@5 { + reg = <5>; + ethernet = <ð0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + + ksz8565: switch@1 { + compatible = "microchip,ksz8565"; + reg = <1>; + + spi-max-frequency = <44000000>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@6 { + reg = <6>; + ethernet = <ð0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,lan937x.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,lan937x.yaml new file mode 100644 index 0000000000..8d7e878b84 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/microchip,lan937x.yaml @@ -0,0 +1,192 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/microchip,lan937x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LAN937x Ethernet Switch Series + +maintainers: + - UNGLinuxDriver@microchip.com + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +properties: + compatible: + enum: + - microchip,lan9370 + - microchip,lan9371 + - microchip,lan9372 + - microchip,lan9373 + - microchip,lan9374 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 50000000 + + reset-gpios: + description: Optional gpio specifier for a reset line + maxItems: 1 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + +patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + allOf: + - if: + properties: + phy-mode: + contains: + enum: + - rgmii + - rgmii-id + - rgmii-txid + - rgmii-rxid + then: + properties: + rx-internal-delay-ps: + enum: [0, 2000] + default: 0 + tx-internal-delay-ps: + enum: [0, 2000] + default: 0 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + macb0 { + #address-cells = <1>; + #size-cells = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + spi { + #address-cells = <1>; + #size-cells = <0>; + + lan9374: switch@0 { + compatible = "microchip,lan9374"; + reg = <0>; + spi-max-frequency = <44000000>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&t1phy0>; + }; + + port@1 { + reg = <1>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&t1phy1>; + }; + + port@2 { + reg = <2>; + label = "lan4"; + phy-mode = "internal"; + phy-handle = <&t1phy2>; + }; + + port@3 { + reg = <3>; + label = "lan6"; + phy-mode = "internal"; + phy-handle = <&t1phy3>; + }; + + port@4 { + reg = <4>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + ethernet = <&macb0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@5 { + reg = <5>; + label = "lan7"; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@6 { + reg = <6>; + label = "lan5"; + phy-mode = "internal"; + phy-handle = <&t1phy6>; + }; + + port@7 { + reg = <7>; + label = "lan3"; + phy-mode = "internal"; + phy-handle = <&t1phy7>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + t1phy0: ethernet-phy@0{ + reg = <0x0>; + }; + + t1phy1: ethernet-phy@1{ + reg = <0x1>; + }; + + t1phy2: ethernet-phy@2{ + reg = <0x2>; + }; + + t1phy3: ethernet-phy@3{ + reg = <0x3>; + }; + + t1phy6: ethernet-phy@6{ + reg = <0x6>; + }; + + t1phy7: ethernet-phy@7{ + reg = <0x7>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml new file mode 100644 index 0000000000..fe02d05196 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml @@ -0,0 +1,260 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mscc,ocelot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Ocelot Switch Family + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + - Claudiu Manoil <claudiu.manoil@nxp.com> + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - UNGLinuxDriver@microchip.com + +description: | + There are multiple switches which are either part of the Ocelot-1 family, or + derivatives of this architecture. These switches can be found embedded in + various SoCs and accessed using MMIO, or as discrete chips and accessed over + SPI or PCIe. The present DSA binding shall be used when the host controlling + them performs packet I/O primarily through an Ethernet port of the switch + (which is attached to an Ethernet port of the host), rather than through + Frame DMA or register-based I/O. + + VSC9953 (Seville): + + This is found in the NXP T1040, where it is a memory-mapped platform + device. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 8 and 9 + - phy-mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3, 4, 5, 6, 7 + + VSC9959 (Felix): + + This is found in the NXP LS1028A. It is a PCI device, part of the larger + enetc root complex. As a result, the ethernet-switch node is a sub-node of + the PCIe root complex node and its "reg" property conforms to the parent + node bindings, describing it as PF 5 of device 0, bus 0. + + If any external switch port is enabled, the enetc PF2 (enetc_port2) should + be enabled as well. This is because the internal MDIO bus (exposed through + EA BAR 0) used to access the MAC PCS registers truly belongs to the enetc + port 2 and not to Felix. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 4 and 5 + - phy-mode = "sgmii": on ports 0, 1, 2, 3 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3 + - phy-mode = "usxgmii": on ports 0, 1, 2, 3 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3 + - phy-mode = "2500base-x": on ports 0, 1, 2, 3 + +properties: + compatible: + enum: + - mscc,vsc9953-switch + - pci1957,eef0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + description: + Used to signal availability of PTP TX timestamps, and state changes of + the MAC merge layer of ports that support Frame Preemption. + + little-endian: true + big-endian: true + +required: + - compatible + - reg + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - if: + properties: + compatible: + const: pci1957,eef0 + then: + required: + - interrupts + +unevaluatedProperties: false + +examples: + # Felix VSC9959 (NXP LS1028A) + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pcie { /* Integrated Endpoint Root Complex */ + #address-cells = <3>; + #size-cells = <2>; + + ethernet-switch@0,5 { + compatible = "pci1957,eef0"; + reg = <0x000500 0 0 0 0>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + ethernet = <&enetc_port2>; + phy-mode = "internal"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@5 { + reg = <5>; + ethernet = <&enetc_port3>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + # Seville VSC9953 (NXP T1040) + - | + soc { + #address-cells = <1>; + #size-cells = <1>; + + ethernet-switch@800000 { + compatible = "mscc,vsc9953-switch"; + reg = <0x800000 0x290000>; + little-endian; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + phy-mode = "qsgmii"; + phy-handle = <&phy4>; + managed = "in-band-status"; + }; + + port@5 { + reg = <5>; + phy-mode = "qsgmii"; + phy-handle = <&phy5>; + managed = "in-band-status"; + }; + + port@6 { + reg = <6>; + phy-mode = "qsgmii"; + phy-handle = <&phy6>; + managed = "in-band-status"; + }; + + port@7 { + reg = <7>; + phy-mode = "qsgmii"; + phy-handle = <&phy7>; + managed = "in-band-status"; + }; + + port@8 { + reg = <8>; + phy-mode = "internal"; + ethernet = <&enet0>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@9 { + reg = <9>; + phy-mode = "internal"; + ethernet = <&enet1>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml new file mode 100644 index 0000000000..4d5f5cc6d0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml @@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP SJA1105 Automotive Ethernet Switch Family + +description: + The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at + least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum + cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed + depends on the SPI bus master driver. + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + +properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105t + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1110a + - nxp,sja1110b + - nxp,sja1110c + - nxp,sja1110d + + reg: + maxItems: 1 + + spi-cpha: true + spi-cpol: true + + # Optional container node for the 2 internal MDIO buses of the SJA1110 + # (one for the internal 100base-T1 PHYs and the other for the single + # 100base-TX PHY). The "reg" property does not have physical significance. + # The PHY addresses to port correspondence is as follows: for 100base-T1, + # port 5 has PHY 1, port 6 has PHY 2 etc, while for 100base-TX, port 1 has + # PHY 1. + mdios: + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^mdio@[0-1]$": + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + oneOf: + - enum: + - nxp,sja1110-base-t1-mdio + - nxp,sja1110-base-tx-mdio + + reg: + oneOf: + - enum: + - 0 + - 1 + + required: + - compatible + - reg + +patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + allOf: + - if: + properties: + phy-mode: + contains: + enum: + - rgmii + - rgmii-rxid + - rgmii-txid + - rgmii-id + then: + properties: + rx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + tx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + +required: + - compatible + - reg + +$defs: + internal-delay-ps: + description: + Disable tunable delay lines using 0 ps, or enable them and select + the phase between 1640 ps (73.8 degree shift at 1Gbps) and 2260 ps + (101.7 degree shift) in increments of 0.9 degrees (20 ps). + enum: + [0, 1640, 1660, 1680, 1700, 1720, 1740, 1760, 1780, 1800, 1820, 1840, + 1860, 1880, 1900, 1920, 1940, 1960, 1980, 2000, 2020, 2040, 2060, 2080, + 2100, 2120, 2140, 2160, 2180, 2200, 2220, 2240, 2260] + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1105t + then: + properties: + spi-cpol: false + required: + - spi-cpha + else: + properties: + spi-cpha: false + required: + - spi-cpol + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@1 { + reg = <0x1>; + compatible = "nxp,sja1105t"; + spi-cpha; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + phy-handle = <&rgmii_phy6>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <0>; + }; + + port@1 { + phy-handle = <&rgmii_phy3>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <1>; + }; + + port@2 { + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <2>; + }; + + port@3 { + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <3>; + }; + + port@4 { + ethernet = <&enet2>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <4>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml new file mode 100644 index 0000000000..df64eebebe --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml @@ -0,0 +1,320 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/qca8k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros QCA83xx switch family + +maintainers: + - John Crispin <john@phrozen.org> + +description: + If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode + describing a port needs to have a valid phandle referencing the internal PHY + it is connected to. This is because there is no N:N mapping of port and PHY + ID. To declare the internal mdio-bus configuration, declare an MDIO node in + the switch node and declare the phandle for the port, referencing the internal + PHY it is connected to. In this config, an internal mdio-bus is registered and + the MDIO master is used for communication. Mixed external and internal + mdio-bus configurations are not supported by the hardware. + Each phy has at most 3 LEDs connected and can be declared + using the standard LEDs structure. + +properties: + compatible: + oneOf: + - enum: + - qca,qca8327 + - qca,qca8328 + - qca,qca8334 + - qca,qca8337 + description: | + qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package + qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package + qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package + qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package + + reg: + maxItems: 1 + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + + qca,ignore-power-on-sel: + $ref: /schemas/types.yaml#/definitions/flag + description: + Ignore power-on pin strapping to configure LED open-drain or EEPROM + presence. This is needed for devices with incorrect configuration or when + the OEM has decided not to use pin strapping and falls back to SW regs. + + qca,led-open-drain: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to + be set, otherwise the driver will fail at probe. This is required if the + OEM does not use pin strapping to set this mode and prefers to set it + using SW regs. The pin strappings related to LED open-drain mode are + B68 on the QCA832x and B49 on the QCA833x. + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Qca8k switch have an internal mdio to access switch port. + If this is not present, the legacy mapping is used and the + internal mdio access is used. + With the legacy mapping the reg corresponding to the internal + mdio is the switch reg with an offset of -1. + +$ref: dsa.yaml# + +patternProperties: + "^(ethernet-)?ports$": + type: object + patternProperties: + "^(ethernet-)?port@[0-6]$": + type: object + description: Ethernet switch ports + + $ref: dsa-port.yaml# + + properties: + qca,sgmii-rxclk-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set the receive clock phase to falling edge. Mostly commonly used on + the QCA8327 with CPU port 0 set to SGMII. + + qca,sgmii-txclk-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set the transmit clock phase to falling edge. + + qca,sgmii-enable-pll: + $ref: /schemas/types.yaml#/definitions/flag + description: + For SGMII CPU port, explicitly enable PLL, TX and RX chain along with + Signal Detection. On the QCA8327 this should not be enabled, otherwise + the SGMII port will not initialize. When used on the QCA8337, revision 3 + or greater, a warning will be displayed. When the CPU port is set to + SGMII on the QCA8337, it is advised to set this unless a communication + issue is observed. + + unevaluatedProperties: false + +oneOf: + - required: + - ports + - required: + - ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + external_phy_port1: ethernet-phy@0 { + reg = <0>; + }; + + external_phy_port2: ethernet-phy@1 { + reg = <1>; + }; + + external_phy_port3: ethernet-phy@2 { + reg = <2>; + }; + + external_phy_port4: ethernet-phy@3 { + reg = <3>; + }; + + external_phy_port5: ethernet-phy@4 { + reg = <4>; + }; + + switch@10 { + compatible = "qca,qca8337"; + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&external_phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&external_phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&external_phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&external_phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-handle = <&external_phy_port5>; + }; + }; + }; + }; + - | + #include <dt-bindings/gpio/gpio.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@10 { + compatible = "qca,qca8337"; + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port1>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_WHITE>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_AMBER>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + }; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port5>; + }; + + port@6 { + reg = <0>; + ethernet = <&gmac1>; + phy-mode = "sgmii"; + + qca,sgmii-rxclk-falling-edge; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + internal_phy_port1: ethernet-phy@0 { + reg = <0>; + }; + + internal_phy_port2: ethernet-phy@1 { + reg = <1>; + }; + + internal_phy_port3: ethernet-phy@2 { + reg = <2>; + }; + + internal_phy_port4: ethernet-phy@3 { + reg = <3>; + }; + + internal_phy_port5: ethernet-phy@4 { + reg = <4>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml new file mode 100644 index 0000000000..cfd69c2604 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml @@ -0,0 +1,386 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/realtek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek switches for unmanaged switches + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + Realtek advertises these chips as fast/gigabit switches or unmanaged + switches. They can be controlled using different interfaces, like SMI, + MDIO or SPI. + + The SMI "Simple Management Interface" is a two-wire protocol using + bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does + not use the MDIO protocol. This binding defines how to specify the + SMI-based Realtek devices. The realtek-smi driver is a platform driver + and it must be inserted inside a platform node. + + The MDIO-connected switches use MDIO protocol to access their registers. + The realtek-mdio driver is an MDIO driver and it must be inserted inside + an MDIO node. + + The compatible string is only used to identify which (silicon) family the + switch belongs to. Roughly speaking, a family is any set of Realtek switches + whose chip identification register(s) have a common location and semantics. + The different models in a given family can be automatically disambiguated by + parsing the chip identification register(s) according to the given family, + avoiding the need for a unique compatible string for each model. + +properties: + compatible: + enum: + - realtek,rtl8365mb + - realtek,rtl8366rb + description: | + realtek,rtl8365mb: + Use with models RTL8363NB, RTL8363NB-VB, RTL8363SC, RTL8363SC-VB, + RTL8364NB, RTL8364NB-VB, RTL8365MB, RTL8366SC, RTL8367RB-VB, RTL8367S, + RTL8367SB, RTL8370MB, RTL8310SR + realtek,rtl8366rb: + Use with models RTL8366RB, RTL8366S + + mdc-gpios: + description: GPIO line for the MDC clock line. + maxItems: 1 + + mdio-gpios: + description: GPIO line for the MDIO data line. + maxItems: 1 + + reset-gpios: + description: GPIO to be used to reset the whole device + maxItems: 1 + + realtek,disable-leds: + type: boolean + description: | + if the LED drivers are not used in the hardware design, + this will disable them so they are not turned on + and wasting power. + + interrupt-controller: + type: object + description: | + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the Realtek switch chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + + properties: + + interrupt-controller: true + + interrupts: + maxItems: 1 + description: + A single IRQ line from the switch, either active LOW or HIGH + + '#address-cells': + const: 0 + + '#interrupt-cells': + const: 1 + + required: + - interrupt-controller + - '#address-cells' + - '#interrupt-cells' + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + const: realtek,smi-mdio + +if: + required: + - reg + +then: + $ref: /schemas/spi/spi-peripheral-props.yaml# + not: + required: + - mdc-gpios + - mdio-gpios + - mdio + + properties: + mdc-gpios: false + mdio-gpios: false + mdio: false + +else: + required: + - mdc-gpios + - mdio-gpios + - mdio + - reset-gpios + +required: + - compatible + + # - mdc-gpios + # - mdio-gpios + # - reset-gpios + # - mdio + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc1: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc1>; + interrupts = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc1>; + interrupts = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc1>; + interrupts = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc1>; + interrupts = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc1>; + interrupts = <12>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8365mb"; + mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + + switch_intc2: interrupt-controller { + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "swp0"; + phy-handle = <ðphy0>; + }; + port@1 { + reg = <1>; + label = "swp1"; + phy-handle = <ðphy1>; + }; + port@2 { + reg = <2>; + label = "swp2"; + phy-handle = <ðphy2>; + }; + port@3 { + reg = <3>; + label = "swp3"; + phy-handle = <ðphy3>; + }; + port@6 { + reg = <6>; + ethernet = <&fec1>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc2>; + interrupts = <0>; + }; + ethphy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc2>; + interrupts = <1>; + }; + ethphy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc2>; + interrupts = <2>; + }; + ethphy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc2>; + interrupts = <3>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@29 { + compatible = "realtek,rtl8365mb"; + reg = <29>; + + reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; + + switch_intc3: interrupt-controller { + interrupt-parent = <&gpio0>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@7 { + reg = <7>; + ethernet = <ðernet>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml new file mode 100644 index 0000000000..833d2f68da --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml @@ -0,0 +1,158 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/renesas,rzn1-a5psw.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/N1 Advanced 5 ports ethernet switch + +maintainers: + - Clément Léger <clement.leger@bootlin.com> + +description: | + The advanced 5 ports switch is present on the Renesas RZ/N1 SoC family and + handles 4 ports + 1 CPU management port. + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +properties: + compatible: + items: + - enum: + - renesas,r9a06g032-a5psw + - const: renesas,rzn1-a5psw + + reg: + maxItems: 1 + + interrupts: + items: + - description: Device Level Ring (DLR) interrupt + - description: Switch interrupt + - description: Parallel Redundancy Protocol (PRP) interrupt + - description: Integrated HUB module interrupt + - description: Receive Pattern Match interrupt + + interrupt-names: + items: + - const: dlr + - const: switch + - const: prp + - const: hub + - const: ptrn + + power-domains: + maxItems: 1 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + clocks: + items: + - description: AHB clock used for the switch register interface + - description: Switch system clock + + clock-names: + items: + - const: hclk + - const: clk + + ethernet-ports: + type: object + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^(ethernet-)?port@[0-4]$": + type: object + description: Ethernet switch ports + + properties: + pcs-handle: + maxItems: 1 + description: + phandle pointing to a PCS sub-node compatible with + renesas,rzn1-miic.yaml# + +unevaluatedProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/r9a06g032-sysctrl.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + switch@44050000 { + compatible = "renesas,r9a06g032-a5psw", "renesas,rzn1-a5psw"; + reg = <0x44050000 0x10000>; + clocks = <&sysctrl R9A06G032_HCLK_SWITCH>, <&sysctrl R9A06G032_CLK_SWITCH>; + clock-names = "hclk", "clk"; + power-domains = <&sysctrl>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "dlr", "switch", "prp", "hub", "ptrn"; + + dsa,member = <0 0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&switch0phy3>; + pcs-handle = <&mii_conv4>; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&switch0phy1>; + pcs-handle = <&mii_conv3>; + }; + + port@4 { + reg = <4>; + ethernet = <&gmac2>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio0a 2 GPIO_ACTIVE_HIGH>; + reset-delay-us = <15>; + clock-frequency = <2500000>; + + switch0phy1: ethernet-phy@1{ + reg = <1>; + }; + + switch0phy3: ethernet-phy@3{ + reg = <3>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt new file mode 100644 index 0000000000..258bef4836 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt @@ -0,0 +1,129 @@ +Vitesse VSC73xx Switches +======================== + +This defines device tree bindings for the Vitesse VSC73xx switch chips. +The Vitesse company has been acquired by Microsemi and Microsemi has +been acquired Microchip but retains this vendor branding. + +The currently supported switch chips are: +Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch +Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch +Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch +Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch + +This switch could have two different management interface. + +If SPI interface is used, the device tree node is an SPI device so it must +reside inside a SPI bus device tree node, see spi/spi-bus.txt + +When the chip is connected to a parallel memory bus and work in memory-mapped +I/O mode, a platform device is used to represent the vsc73xx. In this case it +must reside inside a platform bus device tree node. + +Required properties: + +- compatible: must be exactly one of: + "vitesse,vsc7385" + "vitesse,vsc7388" + "vitesse,vsc7395" + "vitesse,vsc7398" +- gpio-controller: indicates that this switch is also a GPIO controller, + see gpio/gpio.txt +- #gpio-cells: this must be set to <2> and indicates that we are a twocell + GPIO controller, see gpio/gpio.txt + +Optional properties: + +- reset-gpios: a handle to a GPIO line that can issue reset of the chip. + It should be tagged as active low. + +Required subnodes: + +See net/dsa/dsa.txt for a list of additional required and optional properties +and subnodes of DSA switches. + +Examples: + +SPI: +switch@0 { + compatible = "vitesse,vsc7395"; + reg = <0>; + /* Specified for 2.5 MHz or below */ + spi-max-frequency = <2500000>; + gpio-controller; + #gpio-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + vsc: port@6 { + reg = <6>; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; +}; + +Platform: +switch@2,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "vitesse,vsc7385"; + reg = <0x2 0x0 0x20000>; + reset-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + vsc: port@6 { + reg = <6>; + ethernet = <&enet0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + +}; |