diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless')
13 files changed, 2023 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml new file mode 100644 index 0000000000..4aa521f1be --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml @@ -0,0 +1,154 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices + +maintainers: + - Arend van Spriel <arend@broadcom.com> + +description: + The Broadcom Single chip MAC part for the BCM4329 family and + later Cypress chips in the same family named CYW4373 and similar. + These chips also have a Bluetooth portion described in a separate + binding. + +allOf: + - $ref: ieee80211.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,bcm43143-fmac + - brcm,bcm4341b0-fmac + - brcm,bcm4341b4-fmac + - brcm,bcm4341b5-fmac + - brcm,bcm4329-fmac + - brcm,bcm4330-fmac + - brcm,bcm4334-fmac + - brcm,bcm43340-fmac + - brcm,bcm4335-fmac + - brcm,bcm43362-fmac + - brcm,bcm4339-fmac + - brcm,bcm43430a0-fmac + - brcm,bcm43430a1-fmac + - brcm,bcm43455-fmac + - brcm,bcm43456-fmac + - brcm,bcm4354-fmac + - brcm,bcm4356-fmac + - brcm,bcm4359-fmac + - brcm,bcm4366-fmac + - cypress,cyw4373-fmac + - cypress,cyw43012-fmac + - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 + + reg: + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. + + interrupts: + maxItems: 1 + description: Out-of-band (OOB) IRQ line for waking up the host + in response to WLAN activity. This corresponds to the HOST_WAKE + line into the chip. + + interrupt-names: + description: Name for the OOB IRQ, this must be set to "host-wake". + const: host-wake + + brcm,drive-strength: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Drive strength used for the SDIO pins on the device in mA. + minimum: 0 + maximum: 32 + + reset-gpios: + maxItems: 1 + description: A GPIO line connected to the WL_RST line, if present + this shall be flagged as active low. + + brcm,ccode-map: + $ref: /schemas/types.yaml#/definitions/string-array + description: Multiple strings for translating ISO3166 country code to + brcmfmac firmware country code and revision. + items: + pattern: '^[A-Z][A-Z]-[A-Z][0-9A-Z]-[0-9]+$' + + brcm,ccode-map-trivial: + description: | + Use a trivial mapping of ISO3166 country codes to brcmfmac firmware + country code and revision: cc -> { cc, 0 }. In other words, assume that + the CLM blob firmware uses ISO3166 country codes as well, and that all + revisions are zero. This property is mutually exclusive with + brcm,ccode-map. If both properties are specified, then brcm,ccode-map + takes precedence. + type: boolean + + brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present. + + brcm,board-type: + $ref: /schemas/types.yaml#/definitions/string + description: Overrides the board type, which is normally the compatible of + the root node. This can be used to decouple the overall system board or + device name from the board type for WiFi purposes, which is used to + construct firmware and NVRAM configuration filenames, allowing for + multiple devices that share the same module or characteristics for the + WiFi subsystem to share the same firmware/NVRAM files. On Apple platforms, + this should be the Apple module-instance codename prefixed by "apple,", + e.g. "apple,honshu". + + apple,antenna-sku: + $ref: /schemas/types.yaml#/definitions/string + description: Antenna SKU used to identify a specific antenna configuration + on Apple platforms. This is use to build firmware filenames, to allow + platforms with different antenna configs to have different firmware and/or + NVRAM. This would normally be filled in by the bootloader from platform + configuration data. + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + mmc@80118000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80118000 0x1000>; + clocks = <&clk 0>, <&clk 1>; + clock-names = "mclk", "apb_pclk"; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + bus-width = <4>; + non-removable; + vmmc-supply = <&wl_bt_reg>; + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; + reg = <1>; + interrupt-parent = <&gpio>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "host-wake"; + reset-gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + brcm,ccode-map = "JP-JP-78", "US-Q2-86"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.yaml b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.yaml new file mode 100644 index 0000000000..0ea84d6fe7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/esp,esp8089.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Espressif ESP8089 + +maintainers: + - Hans de Goede <hdegoede@redhat.com> + +properties: + compatible: + const: esp,esp8089 + + reg: + maxItems: 1 + + esp,crystal-26M-en: + $ref: /schemas/types.yaml#/definitions/uint32 + description: > + Value for the crystal_26M_en firmware parameter + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + mmc { + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.yaml b/Documentation/devicetree/bindings/net/wireless/ieee80211.yaml new file mode 100644 index 0000000000..d89f7a3f88 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/ieee80211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common IEEE 802.11 + +maintainers: + - Lorenzo Bianconi <lorenzo@kernel.org> + +description: | + This provides documentation of common properties that are valid for + all wireless devices + +properties: + ieee80211-freq-limit: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + minItems: 2 + maxItems: 2 + description: + List of supported frequency ranges in KHz. This can be used for devices + that in a given config support less channels than normally. It may happen + chipset supports a wide wireless band but it is limited to some part of + it due to used antennas or power amplifier. An example case for this + can be tri-band wireless router with two identical chipsets used for two + different 5 GHz subbands. Using them incorrectly could not work or + decrease performance noticeably + +additionalProperties: true + +examples: + - | + pcie0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <2402000 2482000>, + <5170000 5250000>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt new file mode 100644 index 0000000000..cdc303caf5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -0,0 +1,70 @@ +Marvell 8787/8897/8978/8997 (sd8787/sd8897/sd8978/sd8997/pcie8997) SDIO/PCIE devices +------ + +This node provides properties for controlling the Marvell SDIO/PCIE wireless device. +The node is expected to be specified as a child node to the SDIO/PCIE controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8787" + * "marvell,sd8897" + * "marvell,sd8978" + * "marvell,sd8997" + * "nxp,iw416" + * "pci11ab,2b42" + * "pci1b4b,2b42" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + - vmmc-supply: a phandle of a regulator, supplying VCC to the card + - mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*" + for documentation of MMC power sequence bindings. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + vmmc-supply = <&wlan_en_reg>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml new file mode 100644 index 0000000000..252207adbc --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml @@ -0,0 +1,301 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/mediatek,mt76.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek mt76 wireless devices + +maintainers: + - Felix Fietkau <nbd@nbd.name> + - Lorenzo Bianconi <lorenzo@kernel.org> + - Ryder Lee <ryder.lee@mediatek.com> + +description: | + This node provides properties for configuring the MediaTek mt76xx + wireless device. The node is expected to be specified as a child + node of the PCI controller to which the wireless chip is connected. + Alternatively, it can specify the wireless part of the MT7628/MT7688 + or MT7622/MT7986 SoC. + +allOf: + - $ref: ieee80211.yaml# + +properties: + compatible: + enum: + - mediatek,mt76 + - mediatek,mt7628-wmac + - mediatek,mt7622-wmac + - mediatek,mt7981-wmac + - mediatek,mt7986-wmac + + reg: + minItems: 1 + maxItems: 3 + description: + MT7986 should contain 3 regions consys, dcm, and sku, in this order. + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + memory-region: + maxItems: 1 + + resets: + maxItems: 1 + description: + Specify the consys reset for mt7986. + + reset-names: + const: consys + + clocks: + maxItems: 2 + description: + Specify the consys clocks for mt7986. + + clock-names: + items: + - const: mcu + - const: ap2conn + + mediatek,infracfg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the infrastructure bus fabric syscon node. + This property is MT7622 specific + + ieee80211-freq-limit: true + + nvmem-cells: + items: + - description: NVMEM cell with EEPROM + + nvmem-cell-names: + items: + - const: eeprom + + mediatek,eeprom-data: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + EEPROM data embedded as array. + + mediatek,mtd-eeprom: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to MTD partition + - description: offset containing EEPROM data + description: + Phandle to a MTD partition + offset containing EEPROM data + deprecated: true + + big-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: + Specify if the radio eeprom partition is written in big-endian + + mediatek,eeprom-merge-otp: + type: boolean + description: + Merge EEPROM data with OTP data. Can be used on boards where the flash + calibration data is generic and specific calibration data should be + pulled from the OTP ROM + + mediatek,disable-radar-background: + type: boolean + description: + Disable/enable radar/CAC detection running on a dedicated offchannel + chain available on some hw. + Background radar/CAC detection allows to avoid the CAC downtime + switching on a different channel during CAC detection on the selected + radar channel. + + led: + type: object + $ref: /schemas/leds/common.yaml# + additionalProperties: false + properties: + led-active-low: + description: + LED is enabled with ground signal. + type: boolean + + led-sources: + maxItems: 1 + + power-limits: + type: object + additionalProperties: false + patternProperties: + "^r[0-9]+": + type: object + additionalProperties: false + properties: + regdomain: + $ref: /schemas/types.yaml#/definitions/string + description: + Regdomain refers to a legal regulatory region. Different + countries define different levels of allowable transmitter + power, time that a channel can be occupied, and different + available channels + enum: + - FCC + - ETSI + - JP + + patternProperties: + "^txpower-[256]g$": + type: object + additionalProperties: false + patternProperties: + "^b[0-9]+$": + type: object + additionalProperties: false + properties: + channels: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: + Pairs of first and last channel number of the selected + band + + rates-cck: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 4 + maxItems: 4 + description: + 4 half-dBm per-rate power limit values + + rates-ofdm: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 8 + maxItems: 8 + description: + 8 half-dBm per-rate power limit values + + rates-mcs: + $ref: /schemas/types.yaml#/definitions/uint8-matrix + description: + Sets of per-rate power limit values for 802.11n/802.11ac + rates for multiple channel bandwidth settings. + Each set starts with the number of channel bandwidth + settings for which the rate set applies, followed by + either 8 or 10 power limit values. The order of the + channel bandwidth settings is 20, 40, 80 and 160 MHz. + maxItems: 4 + items: + minItems: 9 + maxItems: 11 + + rates-ru: + $ref: /schemas/types.yaml#/definitions/uint8-matrix + description: + Sets of per-rate power limit values for 802.11ax rates + for multiple channel bandwidth or resource unit settings. + Each set starts with the number of channel bandwidth or + resource unit settings for which the rate set applies, + followed by 12 power limit values. The order of the + channel resource unit settings is RU26, RU52, RU106, + RU242/SU20, RU484/SU40, RU996/SU80 and RU2x996/SU160. + items: + minItems: 13 + maxItems: 13 + + txs-delta: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Half-dBm power delta for different numbers of antennas + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + pcie0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + mediatek,mtd-eeprom = <&factory 0x8000>; + big-endian; + + led { + led-sources = <2>; + }; + + power-limits { + r0 { + regdomain = "FCC"; + txpower-5g { + b0 { + channels = <36 48>; + rates-ofdm = /bits/ 8 <23 23 23 23 23 23 23 23>; + rates-mcs = /bits/ 8 <1 23 23 23 23 23 23 23 23 23 23>, + /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22>; + rates-ru = /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22 22 22>, + /bits/ 8 <4 20 20 20 20 20 20 20 20 20 20 20 20>; + }; + b1 { + channels = <100 181>; + rates-ofdm = /bits/ 8 <14 14 14 14 14 14 14 14>; + rates-mcs = /bits/ 8 <4 14 14 14 14 14 14 14 14 14 14>; + txs-delta = <12 9 6>; + rates-ru = /bits/ 8 <7 14 14 14 14 14 14 14 14 14 14 14 14>; + }; + }; + }; + }; + }; + }; + + - | + wifi@10300000 { + compatible = "mediatek,mt7628-wmac"; + reg = <0x10300000 0x100000>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + nvmem-cells = <&eeprom>; + nvmem-cell-names = "eeprom"; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + wifi@18000000 { + compatible = "mediatek,mt7622-wmac"; + reg = <0x10300000 0x100000>; + interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_LOW>; + + mediatek,infracfg = <&infracfg>; + + power-domains = <&scpsys 3>; + }; + + - | + wifi@18000000 { + compatible = "mediatek,mt7986-wmac"; + resets = <&watchdog 23>; + reset-names = "consys"; + reg = <0x18000000 0x1000000>, + <0x10003000 0x1000>, + <0x11d10000 0x1000>; + interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen 50>, + <&topckgen 62>; + clock-names = "mcu", "ap2conn"; + memory-region = <&wmcpu_emi>; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml new file mode 100644 index 0000000000..2460ccc082 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip WILC wireless + +maintainers: + - Adham Abozaeid <adham.abozaeid@microchip.com> + - Ajay Singh <ajay.kathat@microchip.com> + +description: + The wilc1000 chips can be connected via SPI or SDIO. This document + describes the binding to connect wilc devices. + +properties: + compatible: + const: microchip,wilc1000 + + reg: true + + interrupts: + maxItems: 1 + + clocks: + description: phandle to the clock connected on rtc clock line. + maxItems: 1 + + clock-names: + const: rtc + + enable-gpios: + maxItems: 1 + description: Used by wilc1000-spi to determine the GPIO line + connected to the ENABLE line. If specified, reset-gpios + must be specified as well as otherwise the driver cannot + ensure the timing required between asserting ENABLE + and deasserting RESET. This should be declared as an + active-high signal. + + reset-gpios: + maxItems: 1 + description: Used by wilc1000-spi to determine the GPIO line + connected to the RESET line. This should be declared as an + active-low signal. + +required: + - compatible + - interrupts + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + wifi@0 { + compatible = "microchip,wilc1000"; + spi-max-frequency = <48000000>; + reg = <0>; + interrupt-parent = <&pioC>; + interrupts = <27 0>; + clocks = <&pck1>; + clock-names = "rtc"; + enable-gpios = <&pioA 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pioA 6 GPIO_ACTIVE_LOW>; + }; + }; + + - | + mmc { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; + non-removable; + vmmc-supply = <&vcc_mmc1_reg>; + vqmmc-supply = <&vcc_3v3_reg>; + bus-width = <4>; + wifi@0 { + compatible = "microchip,wilc1000"; + reg = <0>; + interrupt-parent = <&pioC>; + interrupts = <27 0>; + clocks = <&pck1>; + clock-names = "rtc"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml new file mode 100644 index 0000000000..0e5412cff2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qca,ath9k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros ath9k wireless devices + +maintainers: + - Toke Høiland-Jørgensen <toke@toke.dk> + +description: | + This node provides properties for configuring the ath9k wireless device. + The node is expected to be specified as a child node of the PCI controller + to which the wireless chip is connected. + +allOf: + - $ref: ieee80211.yaml# + +properties: + compatible: + enum: + - pci168c,0023 # AR5416 + - pci168c,0024 # AR5418 + - pci168c,0027 # AR9160 + - pci168c,0029 # AR9220 and AR9223 + - pci168c,002a # AR9280 and AR9283 + - pci168c,002b # AR9285 + - pci168c,002c # AR2427 - 802.11n bonded out + - pci168c,002d # AR9227 + - pci168c,002e # AR9287 + - pci168c,0030 # AR9380, AR9381 and AR9382 + - pci168c,0032 # AR9485 + - pci168c,0033 # AR9580 and AR9590 + - pci168c,0034 # AR9462 + - pci168c,0036 # AR9565 + - pci168c,0037 # AR1111 and AR9485 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + ieee80211-freq-limit: true + + qca,no-eeprom: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates that there is no physical EEPROM connected + + nvmem-cells: + items: + - description: Reference to an nvmem node for the MAC address + - description: Reference to an nvmem node for calibration data + + nvmem-cell-names: + items: + - const: mac-address + - const: calibration + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pcie0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,0 { + compatible = "pci168c,002d"; + reg = <0 0 0 0 0>; + interrupts = <3>; + qca,no-eeprom; + }; + }; + - | + pci0 { + #address-cells = <3>; + #size-cells = <2>; + wifi@0,11 { + compatible = "pci168c,0029"; + reg = <0x8800 0 0 0 0>; + nvmem-cells = <&macaddr_art_c>, <&cal_art_1000>; + nvmem-cell-names = "mac-address", "calibration"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml new file mode 100644 index 0000000000..7758a55dd3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml @@ -0,0 +1,362 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qcom,ath10k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies ath10k wireless devices + +maintainers: + - Kalle Valo <kvalo@kernel.org> + +description: + Qualcomm Technologies, Inc. IEEE 802.11ac devices. + +properties: + compatible: + enum: + - qcom,ath10k # SDIO-based devices + - qcom,ipq4019-wifi + - qcom,wcn3990-wifi # SNoC-based devices + + reg: + maxItems: 1 + + reg-names: + items: + - const: membase + + interrupts: + minItems: 12 + maxItems: 17 + + interrupt-names: + minItems: 12 + maxItems: 17 + + memory-region: + maxItems: 1 + description: + Reference to the MSA memory region used by the Wi-Fi firmware + running on the Q6 core. + + iommus: + minItems: 1 + maxItems: 2 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + resets: + maxItems: 6 + + reset-names: + items: + - const: wifi_cpu_init + - const: wifi_radio_srif + - const: wifi_radio_warm + - const: wifi_radio_cold + - const: wifi_core_warm + - const: wifi_core_cold + + ext-fem-name: + $ref: /schemas/types.yaml#/definitions/string + description: Name of external front end module used. + enum: + - microsemi-lx5586 + - sky85703-11 + - sky85803 + + wifi-firmware: + type: object + additionalProperties: false + description: | + The ath10k Wi-Fi node can contain one optional firmware subnode. + Firmware subnode is needed when the platform does not have Trustzone. + properties: + iommus: + maxItems: 1 + required: + - iommus + + ieee80211-freq-limit: true + + qcom,ath10k-calibration-data: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Calibration data + board-specific data as a byte array. The length + can vary between hardware versions. + + qcom,ath10k-calibration-variant: + $ref: /schemas/types.yaml#/definitions/string + description: + Unique variant identifier of the calibration data in board-2.bin + for designs with colliding bus and device specific ids + + qcom,ath10k-pre-calibration-data: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Pre-calibration data as a byte array. The length can vary between + hardware versions. + + qcom,coexist-support: + $ref: /schemas/types.yaml#/definitions/uint8 + enum: [0, 1] + description: + Indicate coex support by the hardware. + + qcom,coexist-gpio-pin: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + COEX GPIO number provided to the Wi-Fi firmware. + + qcom,msa-fixed-perm: + type: boolean + description: + Whether to skip executing an SCM call that reassigns the memory + region ownership. + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: State bits used by the AP to signal the WLAN Q6. + items: + - description: Signal bits used to enable/disable low power mode + on WCN in the case of WoW (Wake on Wireless). + + qcom,smem-state-names: + description: The names of the state bits used for SMP2P output. + items: + - const: wlan-smp2p-out + + qcom,snoc-host-cap-8bit-quirk: + type: boolean + description: + Quirk specifying that the firmware expects the 8bit version + of the host capability QMI request + + qcom,xo-cal-data: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + XO cal offset to be configured in XO trim register. + + vdd-0.8-cx-mx-supply: + description: Main logic power rail + + vdd-1.8-xo-supply: + description: Crystal oscillator supply + + vdd-1.3-rfa-supply: + description: RFA supply + + vdd-3.3-ch0-supply: + description: Primary Wi-Fi antenna supply + + vdd-3.3-ch1-supply: + description: Secondary Wi-Fi antenna supply + +required: + - compatible + - reg + +additionalProperties: false + +allOf: + - $ref: ieee80211.yaml# + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq4019-wifi + then: + properties: + interrupts: + minItems: 17 + maxItems: 17 + + interrupt-names: + items: + - const: msi0 + - const: msi1 + - const: msi2 + - const: msi3 + - const: msi4 + - const: msi5 + - const: msi6 + - const: msi7 + - const: msi8 + - const: msi9 + - const: msi10 + - const: msi11 + - const: msi12 + - const: msi13 + - const: msi14 + - const: msi15 + - const: legacy + + clocks: + items: + - description: Wi-Fi command clock + - description: Wi-Fi reference clock + - description: Wi-Fi RTC clock + + clock-names: + items: + - const: wifi_wcss_cmd + - const: wifi_wcss_ref + - const: wifi_wcss_rtc + + required: + - clocks + - clock-names + - interrupts + - interrupt-names + - resets + - reset-names + + - if: + properties: + compatible: + contains: + enum: + - qcom,wcn3990-wifi + + then: + properties: + clocks: + minItems: 1 + items: + - description: XO reference clock + - description: Qualcomm Debug Subsystem clock + + clock-names: + minItems: 1 + items: + - const: cxo_ref_clk_pin + - const: qdss + + interrupts: + items: + - description: CE0 + - description: CE1 + - description: CE2 + - description: CE3 + - description: CE4 + - description: CE5 + - description: CE6 + - description: CE7 + - description: CE8 + - description: CE9 + - description: CE10 + - description: CE11 + + interrupt-names: false + + required: + - interrupts + +examples: + # SNoC + - | + #include <dt-bindings/clock/qcom,rpmcc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + wifi@18800000 { + compatible = "qcom,wcn3990-wifi"; + reg = <0x18800000 0x800000>; + reg-names = "membase"; + memory-region = <&wlan_msa_mem>; + clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>; + clock-names = "cxo_ref_clk_pin"; + interrupts = <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&anoc2_smmu 0x1900>, + <&anoc2_smmu 0x1901>; + qcom,snoc-host-cap-8bit-quirk; + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + vdd-3.3-ch1-supply = <&vreg_l23a_3p3>; + + wifi-firmware { + iommus = <&apps_smmu 0x1c02 0x1>; + }; + }; + + # AHB + - | + #include <dt-bindings/clock/qcom,gcc-ipq4019.h> + + wifi@a000000 { + compatible = "qcom,ipq4019-wifi"; + reg = <0xa000000 0x200000>; + resets = <&gcc WIFI0_CPU_INIT_RESET>, + <&gcc WIFI0_RADIO_SRIF_RESET>, + <&gcc WIFI0_RADIO_WARM_RESET>, + <&gcc WIFI0_RADIO_COLD_RESET>, + <&gcc WIFI0_CORE_WARM_RESET>, + <&gcc WIFI0_CORE_COLD_RESET>; + reset-names = "wifi_cpu_init", + "wifi_radio_srif", + "wifi_radio_warm", + "wifi_radio_cold", + "wifi_core_warm", + "wifi_core_cold"; + clocks = <&gcc GCC_WCSS2G_CLK>, + <&gcc GCC_WCSS2G_REF_CLK>, + <&gcc GCC_WCSS2G_RTC_CLK>; + clock-names = "wifi_wcss_cmd", + "wifi_wcss_ref", + "wifi_wcss_rtc"; + interrupts = <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 40 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi0", + "msi1", + "msi2", + "msi3", + "msi4", + "msi5", + "msi6", + "msi7", + "msi8", + "msi9", + "msi10", + "msi11", + "msi12", + "msi13", + "msi14", + "msi15", + "legacy"; + ieee80211-freq-limit = <5470000 5875000>; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml new file mode 100644 index 0000000000..817f02a8b4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k-pci.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2023 Linaro Limited +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k-pci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies ath11k wireless devices (PCIe) + +maintainers: + - Kalle Valo <kvalo@kernel.org> + +description: | + Qualcomm Technologies IEEE 802.11ax PCIe devices + +properties: + compatible: + enum: + - pci17cb,1103 # WCN6855 + + reg: + maxItems: 1 + + qcom,ath11k-calibration-variant: + $ref: /schemas/types.yaml#/definitions/string + description: | + string to uniquely identify variant of the calibration data for designs + with colliding bus and device ids + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pcie { + #address-cells = <3>; + #size-cells = <2>; + + pcie@0 { + device_type = "pci"; + reg = <0x0 0x0 0x0 0x0 0x0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + bus-range = <0x01 0xff>; + + wifi@0 { + compatible = "pci17cb,1103"; + reg = <0x10000 0x0 0x0 0x0 0x0>; + + qcom,ath11k-calibration-variant = "LE_X13S"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml new file mode 100644 index 0000000000..7d5f982a3d --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml @@ -0,0 +1,468 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies ath11k wireless devices + +maintainers: + - Kalle Valo <kvalo@kernel.org> + +description: | + These are dt entries for Qualcomm Technologies, Inc. IEEE 802.11ax + devices, for example like AHB based IPQ8074. + +properties: + compatible: + enum: + - qcom,ipq8074-wifi + - qcom,ipq6018-wifi + - qcom,wcn6750-wifi + - qcom,ipq5018-wifi + + reg: + maxItems: 1 + + interrupts: + minItems: 32 + maxItems: 52 + + interrupt-names: + maxItems: 52 + + qcom,rproc: + $ref: /schemas/types.yaml#/definitions/phandle + description: + DT entry of q6v5-wcss remoteproc driver. + Phandle to a node that can contain the following properties + * compatible + * reg + * reg-names + + qcom,ath11k-calibration-variant: + $ref: /schemas/types.yaml#/definitions/string + description: + string to uniquely identify variant of the calibration data in the + board-2.bin for designs with colliding bus and device specific ids + + memory-region: + minItems: 1 + maxItems: 2 + description: + phandle to a node describing reserved memory (System RAM memory) + used by ath11k firmware (see bindings/reserved-memory/reserved-memory.txt) + + iommus: + minItems: 1 + maxItems: 2 + + wifi-firmware: + type: object + description: | + WCN6750 wifi node can contain one optional firmware subnode. + Firmware subnode is needed when the platform does not have Trustzone. + required: + - iommus + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: State bits used by the AP to signal the WLAN Q6. + items: + - description: Signal bits used to enable/disable low power mode + on WCN6750 in the case of WoW (Wake on Wireless). + + qcom,smem-state-names: + description: The names of the state bits used for SMP2P output. + items: + - const: wlan-smp2p-out + +required: + - compatible + - reg + - interrupts + - qcom,rproc + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq8074-wifi + - qcom,ipq6018-wifi + then: + properties: + interrupts: + items: + - description: misc-pulse1 interrupt events + - description: misc-latch interrupt events + - description: sw exception interrupt events + - description: watchdog interrupt events + - description: interrupt event for ring CE0 + - description: interrupt event for ring CE1 + - description: interrupt event for ring CE2 + - description: interrupt event for ring CE3 + - description: interrupt event for ring CE4 + - description: interrupt event for ring CE5 + - description: interrupt event for ring CE6 + - description: interrupt event for ring CE7 + - description: interrupt event for ring CE8 + - description: interrupt event for ring CE9 + - description: interrupt event for ring CE10 + - description: interrupt event for ring CE11 + - description: interrupt event for ring host2wbm-desc-feed + - description: interrupt event for ring host2reo-re-injection + - description: interrupt event for ring host2reo-command + - description: interrupt event for ring host2rxdma-monitor-ring3 + - description: interrupt event for ring host2rxdma-monitor-ring2 + - description: interrupt event for ring host2rxdma-monitor-ring1 + - description: interrupt event for ring reo2ost-exception + - description: interrupt event for ring wbm2host-rx-release + - description: interrupt event for ring reo2host-status + - description: interrupt event for ring reo2host-destination-ring4 + - description: interrupt event for ring reo2host-destination-ring3 + - description: interrupt event for ring reo2host-destination-ring2 + - description: interrupt event for ring reo2host-destination-ring1 + - description: interrupt event for ring rxdma2host-monitor-destination-mac3 + - description: interrupt event for ring rxdma2host-monitor-destination-mac2 + - description: interrupt event for ring rxdma2host-monitor-destination-mac1 + - description: interrupt event for ring ppdu-end-interrupts-mac3 + - description: interrupt event for ring ppdu-end-interrupts-mac2 + - description: interrupt event for ring ppdu-end-interrupts-mac1 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac3 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac2 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac1 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac3 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac2 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac1 + - description: interrupt event for ring rxdma2host-destination-ring-mac3 + - description: interrupt event for ring rxdma2host-destination-ring-mac2 + - description: interrupt event for ring rxdma2host-destination-ring-mac1 + - description: interrupt event for ring host2tcl-input-ring4 + - description: interrupt event for ring host2tcl-input-ring3 + - description: interrupt event for ring host2tcl-input-ring2 + - description: interrupt event for ring host2tcl-input-ring1 + - description: interrupt event for ring wbm2host-tx-completions-ring3 + - description: interrupt event for ring wbm2host-tx-completions-ring2 + - description: interrupt event for ring wbm2host-tx-completions-ring1 + - description: interrupt event for ring tcl2host-status-ring + interrupt-names: + items: + - const: misc-pulse1 + - const: misc-latch + - const: sw-exception + - const: watchdog + - const: ce0 + - const: ce1 + - const: ce2 + - const: ce3 + - const: ce4 + - const: ce5 + - const: ce6 + - const: ce7 + - const: ce8 + - const: ce9 + - const: ce10 + - const: ce11 + - const: host2wbm-desc-feed + - const: host2reo-re-injection + - const: host2reo-command + - const: host2rxdma-monitor-ring3 + - const: host2rxdma-monitor-ring2 + - const: host2rxdma-monitor-ring1 + - const: reo2ost-exception + - const: wbm2host-rx-release + - const: reo2host-status + - const: reo2host-destination-ring4 + - const: reo2host-destination-ring3 + - const: reo2host-destination-ring2 + - const: reo2host-destination-ring1 + - const: rxdma2host-monitor-destination-mac3 + - const: rxdma2host-monitor-destination-mac2 + - const: rxdma2host-monitor-destination-mac1 + - const: ppdu-end-interrupts-mac3 + - const: ppdu-end-interrupts-mac2 + - const: ppdu-end-interrupts-mac1 + - const: rxdma2host-monitor-status-ring-mac3 + - const: rxdma2host-monitor-status-ring-mac2 + - const: rxdma2host-monitor-status-ring-mac1 + - const: host2rxdma-host-buf-ring-mac3 + - const: host2rxdma-host-buf-ring-mac2 + - const: host2rxdma-host-buf-ring-mac1 + - const: rxdma2host-destination-ring-mac3 + - const: rxdma2host-destination-ring-mac2 + - const: rxdma2host-destination-ring-mac1 + - const: host2tcl-input-ring4 + - const: host2tcl-input-ring3 + - const: host2tcl-input-ring2 + - const: host2tcl-input-ring1 + - const: wbm2host-tx-completions-ring3 + - const: wbm2host-tx-completions-ring2 + - const: wbm2host-tx-completions-ring1 + - const: tcl2host-status-ring + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq8074-wifi + - qcom,ipq6018-wifi + then: + required: + - interrupt-names + + - if: + properties: + compatible: + contains: + enum: + - qcom,wcn6750-wifi + then: + properties: + interrupts: + items: + - description: interrupt event for ring CE1 + - description: interrupt event for ring CE2 + - description: interrupt event for ring CE3 + - description: interrupt event for ring CE4 + - description: interrupt event for ring CE5 + - description: interrupt event for ring CE6 + - description: interrupt event for ring CE7 + - description: interrupt event for ring CE8 + - description: interrupt event for ring CE9 + - description: interrupt event for ring CE10 + - description: interrupt event for ring DP1 + - description: interrupt event for ring DP2 + - description: interrupt event for ring DP3 + - description: interrupt event for ring DP4 + - description: interrupt event for ring DP5 + - description: interrupt event for ring DP6 + - description: interrupt event for ring DP7 + - description: interrupt event for ring DP8 + - description: interrupt event for ring DP9 + - description: interrupt event for ring DP10 + - description: interrupt event for ring DP11 + - description: interrupt event for ring DP12 + - description: interrupt event for ring DP13 + - description: interrupt event for ring DP14 + - description: interrupt event for ring DP15 + - description: interrupt event for ring DP16 + - description: interrupt event for ring DP17 + - description: interrupt event for ring DP18 + - description: interrupt event for ring DP19 + - description: interrupt event for ring DP20 + - description: interrupt event for ring DP21 + - description: interrupt event for ring DP22 + +examples: + - | + + q6v5_wcss: remoteproc@cd00000 { + compatible = "qcom,ipq8074-wcss-pil"; + reg = <0xcd00000 0x4040>, + <0x4ab000 0x20>; + reg-names = "qdsp6", + "rmb"; + }; + + wifi0: wifi@c000000 { + compatible = "qcom,ipq8074-wifi"; + reg = <0xc000000 0x2000000>; + interrupts = <0 320 1>, + <0 319 1>, + <0 318 1>, + <0 317 1>, + <0 316 1>, + <0 315 1>, + <0 314 1>, + <0 311 1>, + <0 310 1>, + <0 411 1>, + <0 410 1>, + <0 40 1>, + <0 39 1>, + <0 302 1>, + <0 301 1>, + <0 37 1>, + <0 36 1>, + <0 296 1>, + <0 295 1>, + <0 294 1>, + <0 293 1>, + <0 292 1>, + <0 291 1>, + <0 290 1>, + <0 289 1>, + <0 288 1>, + <0 239 1>, + <0 236 1>, + <0 235 1>, + <0 234 1>, + <0 233 1>, + <0 232 1>, + <0 231 1>, + <0 230 1>, + <0 229 1>, + <0 228 1>, + <0 224 1>, + <0 223 1>, + <0 203 1>, + <0 183 1>, + <0 180 1>, + <0 179 1>, + <0 178 1>, + <0 177 1>, + <0 176 1>, + <0 163 1>, + <0 162 1>, + <0 160 1>, + <0 159 1>, + <0 158 1>, + <0 157 1>, + <0 156 1>; + interrupt-names = "misc-pulse1", + "misc-latch", + "sw-exception", + "watchdog", + "ce0", + "ce1", + "ce2", + "ce3", + "ce4", + "ce5", + "ce6", + "ce7", + "ce8", + "ce9", + "ce10", + "ce11", + "host2wbm-desc-feed", + "host2reo-re-injection", + "host2reo-command", + "host2rxdma-monitor-ring3", + "host2rxdma-monitor-ring2", + "host2rxdma-monitor-ring1", + "reo2ost-exception", + "wbm2host-rx-release", + "reo2host-status", + "reo2host-destination-ring4", + "reo2host-destination-ring3", + "reo2host-destination-ring2", + "reo2host-destination-ring1", + "rxdma2host-monitor-destination-mac3", + "rxdma2host-monitor-destination-mac2", + "rxdma2host-monitor-destination-mac1", + "ppdu-end-interrupts-mac3", + "ppdu-end-interrupts-mac2", + "ppdu-end-interrupts-mac1", + "rxdma2host-monitor-status-ring-mac3", + "rxdma2host-monitor-status-ring-mac2", + "rxdma2host-monitor-status-ring-mac1", + "host2rxdma-host-buf-ring-mac3", + "host2rxdma-host-buf-ring-mac2", + "host2rxdma-host-buf-ring-mac1", + "rxdma2host-destination-ring-mac3", + "rxdma2host-destination-ring-mac2", + "rxdma2host-destination-ring-mac1", + "host2tcl-input-ring4", + "host2tcl-input-ring3", + "host2tcl-input-ring2", + "host2tcl-input-ring1", + "wbm2host-tx-completions-ring3", + "wbm2host-tx-completions-ring2", + "wbm2host-tx-completions-ring1", + "tcl2host-status-ring"; + qcom,rproc = <&q6v5_wcss>; + }; + + - | + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + + qcn9074_0: wifi@51100000 { + no-map; + reg = <0x0 0x51100000 0x0 0x03500000>; + }; + }; + + pci { + pcie0 { + #size-cells = <2>; + #address-cells = <3>; + + wifi_0: wifi@0 { + reg = <0 0 0 0 0>; + memory-region = <&qcn9074_0>; + }; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + + wlan_ce_mem: memory@4cd000 { + no-map; + reg = <0x0 0x004cd000 0x0 0x1000>; + }; + + wlan_fw_mem: memory@80c00000 { + no-map; + reg = <0x0 0x80c00000 0x0 0xc00000>; + }; + }; + + wifi: wifi@17a10040 { + compatible = "qcom,wcn6750-wifi"; + reg = <0x17a10040 0x0>; + iommus = <&apps_smmu 0x1c00 0x1>; + interrupts = <GIC_SPI 768 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 769 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 770 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 771 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 772 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 773 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 774 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 775 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 776 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 777 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 778 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 779 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 780 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 781 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 782 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 783 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 784 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 785 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 786 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 787 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 788 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 789 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 790 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 791 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 792 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 793 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 794 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 795 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 796 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 797 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 798 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 799 IRQ_TYPE_EDGE_RISING>; + qcom,rproc = <&remoteproc_wpss>; + memory-region = <&wlan_fw_mem>, <&wlan_ce_mem>; + qcom,smem-states = <&wlan_smp2p_out 0>; + qcom,smem-state-names = "wlan-smp2p-out"; + wifi-firmware { + iommus = <&apps_smmu 0x1c02 0x1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml new file mode 100644 index 0000000000..84e5659e50 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020, Silicon Laboratories, Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Labs WFxxx + +maintainers: + - Jérôme Pouiller <jerome.pouiller@silabs.com> + +description: > + Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device + from the WFxxx series is the WF200 described here: + https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf + + The WF200 can be connected via SPI or via SDIO. + + For SDIO: + + Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is + sufficient for the SDIO devices). + + It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without + it, you may encounter issues during reboot. The mmc-pwrseq should be + compatible with mmc-pwrseq-simple. Please consult + Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more + information. + +properties: + compatible: + items: + - enum: + - prt,prtt1c-wfm200 # Protonic PRTT1C Board + - silabs,brd4001a # WGM160P Evaluation Board + - silabs,brd8022a # WF200 Evaluation Board + - silabs,brd8023a # WFM200 Evaluation Board + - const: silabs,wf200 # Chip alone without antenna + + reg: + description: + When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is + the chip select address of the device as defined in the SPI devices + bindings. + maxItems: 1 + + interrupts: + description: The interrupt line. Should be IRQ_TYPE_EDGE_RISING. When SPI is + used, this property is required. When SDIO is used, the "in-band" + interrupt provided by the SDIO bus is used unless an interrupt is defined + in the Device Tree. + maxItems: 1 + + reset-gpios: + description: (SPI only) Phandle of gpio that will be used to reset chip + during probe. Without this property, you may encounter issues with warm + boot. + + For SDIO, the reset gpio should declared using a mmc-pwrseq. + maxItems: 1 + + wakeup-gpios: + description: Phandle of gpio that will be used to wake-up chip. Without this + property, driver will disable most of power saving features. + maxItems: 1 + + silabs,antenna-config-file: + $ref: /schemas/types.yaml#/definitions/string + description: Use an alternative file for antenna configuration (aka + "Platform Data Set" in Silabs jargon). Default depends of "compatible" + string. For "silabs,wf200", the default is 'wf200.pds'. + + local-mac-address: true + + mac-address: true + +required: + - compatible + - reg + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + wifi@0 { + compatible = "silabs,brd8022a", "silabs,wf200"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_irq &wfx_gpios>; + reg = <0>; + interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>; + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + spi-max-frequency = <42000000>; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + wfx_pwrseq: wfx_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_reset>; + reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + mmc { + mmc-pwrseq = <&wfx_pwrseq>; + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "silabs,brd8022a", "silabs,wf200"; + pinctrl-names = "default"; + pinctrl-0 = <&wfx_wakeup>; + reg = <1>; + wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt new file mode 100644 index 0000000000..88fd28d15e --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -0,0 +1,64 @@ +* Texas Instruments wl1251 wireless lan controller + +The wl1251 chip can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be "ti,wl1251" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- interrupts : Should contain interrupt line +- vio-supply : phandle to regulator providing VIO + +Optional properties: +- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which + provides configuration data (calibration, MAC, ...) +- ti,power-gpio : GPIO connected to chip's PMEN pin if operated in + SPI mode +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +&spi1 { + wl1251@0 { + compatible = "ti,wl1251"; + + reg = <0>; + spi-max-frequency = <48000000>; + spi-cpol; + spi-cpha; + + interrupt-parent = <&gpio2>; + interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */ + + vio-supply = <&vio>; + ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ + }; +}; + +&mmc3 { + vmmc-supply = <&wlan_en>; + + bus-width = <4>; + non-removable; + ti,non-removable; + cap-power-off-card; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; + + #address-cells = <1>; + #size-cells = <0>; + + wlan: wifi@1 { + compatible = "ti,wl1251"; + + reg = <1>; + + interrupt-parent = <&gpio1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_21 */ + + ti,wl1251-has-eeprom; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml new file mode 100644 index 0000000000..75c9489f31 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/ti,wlcore.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments Wilink 6/7/8 (wl12xx/wl18xx) Wireless LAN Controller + +maintainers: + - Tony Lindgren <tony@atomide.com> + +description: + The wl12xx/wl18xx chips can be connected via SPI or via SDIO. + Note that the *-clock-frequency properties assume internal clocks. In case + of external clocks, new bindings (for parsing the clock nodes) have to be + added. + +properties: + compatible: + enum: + - ti,wl1271 + - ti,wl1273 + - ti,wl1281 + - ti,wl1283 + - ti,wl1285 + - ti,wl1801 + - ti,wl1805 + - ti,wl1807 + - ti,wl1831 + - ti,wl1835 + - ti,wl1837 + + reg: + maxItems: 1 + description: + This is required when connected via SPI, and optional when connected via + SDIO. + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + items: + - const: irq + - const: wakeup + + vwlan-supply: + description: + Points to the node of the regulator that powers/enable the wl12xx/wl18xx + chip. This is required when connected via SPI. + + + ref-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Reference clock frequency. + + tcxo-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TCXO clock frequency. + + clock-xtal: + $ref: /schemas/types.yaml#/definitions/flag + description: Indicates that the clock is generated from XTAL. + +required: + - compatible + - interrupts + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + contains: + enum: + - ti,wl1271 + - ti,wl1273 + - ti,wl1281 + - ti,wl1283 + then: + required: + - ref-clock-frequency + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + // For wl12xx family: + spi { + #address-cells = <1>; + #size-cells = <0>; + + wlcore1: wlcore@1 { + compatible = "ti,wl1271"; + reg = <1>; + spi-max-frequency = <48000000>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + vwlan-supply = <&vwlan_fixed>; + clock-xtal; + ref-clock-frequency = <38400000>; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + // For wl18xx family: + spi { + #address-cells = <1>; + #size-cells = <0>; + + wlcore2: wlcore@0 { + compatible = "ti,wl1835"; + reg = <0>; + spi-max-frequency = <48000000>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + vwlan-supply = <&vwlan_fixed>; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + // SDIO example: + mmc3 { + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + + wlcore3: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; + }; |