summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/usb/dwc3-st.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/usb/dwc3-st.txt')
-rw-r--r--Documentation/devicetree/bindings/usb/dwc3-st.txt66
1 files changed, 66 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt
new file mode 100644
index 000000000..4aa368447
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt
@@ -0,0 +1,66 @@
+ST DWC3 glue logic
+
+This file documents the parameters for the dwc3-st driver.
+This driver controls the glue logic used to configure the dwc3 core on
+STiH407 based platforms.
+
+Required properties:
+ - compatible : must be "st,stih407-dwc3"
+ - reg : glue logic base address and USB syscfg ctrl register offset
+ - reg-names : should be "reg-glue" and "syscfg-reg"
+ - st,syscon : should be phandle to system configuration node which
+ encompasses the glue registers
+ - resets : list of phandle and reset specifier pairs. There should be two entries, one
+ for the powerdown and softreset lines of the usb3 IP
+ - reset-names : list of reset signal names. Names should be "powerdown" and "softreset"
+See: Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+ with 'reg' property
+
+ - pinctl-names : A pinctrl state named "default" must be defined
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+ - pinctrl-0 : Pin control group
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+ - ranges : allows valid 1:1 translation between child's address space and
+ parent's address space
+
+Sub-nodes:
+The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
+example below. The DT binding details of dwc3 can be found in:
+Documentation/devicetree/bindings/usb/snps,dwc3.yaml
+
+NB: The dr_mode property described in [1] is NOT optional for this driver, as the default value
+is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are either "host"
+or "device".
+
+[1] Documentation/devicetree/bindings/usb/usb-drd.yaml
+
+Example:
+
+st_dwc3: dwc3@8f94000 {
+ compatible = "st,stih407-dwc3";
+ reg = <0x08f94000 0x1000>, <0x110 0x4>;
+ reg-names = "reg-glue", "syscfg-reg";
+ st,syscfg = <&syscfg_core>;
+ resets = <&powerdown STIH407_USB3_POWERDOWN>,
+ <&softreset STIH407_MIPHY2_SOFTRESET>;
+ reset-names = "powerdown", "softreset";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb3>;
+ ranges;
+
+ dwc3: dwc3@9900000 {
+ compatible = "snps,dwc3";
+ reg = <0x09900000 0x100000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>;
+ dr_mode = "host";
+ phy-names = "usb2-phy", "usb3-phy";
+ phys = <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>;
+ };
+};