diff options
Diffstat (limited to 'arch/arc/boot/dts/axc003_idu.dtsi')
| -rw-r--r-- | arch/arc/boot/dts/axc003_idu.dtsi | 167 |
1 files changed, 167 insertions, 0 deletions
diff --git a/arch/arc/boot/dts/axc003_idu.dtsi b/arch/arc/boot/dts/axc003_idu.dtsi new file mode 100644 index 0000000000..67556f4b70 --- /dev/null +++ b/arch/arc/boot/dts/axc003_idu.dtsi @@ -0,0 +1,167 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2014, 2015 Synopsys, Inc. (www.synopsys.com) + */ + +/* + * Device tree for AXC003 CPU card: HS38x2 (Dual Core) with IDU intc + */ + +/include/ "skeleton_hs_idu.dtsi" + +/ { + compatible = "snps,arc"; + #address-cells = <2>; + #size-cells = <2>; + + cpu_card { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x00000000 0x0 0xf0000000 0x10000000>; + + input_clk: input-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <33333333>; + }; + + core_clk: core-clk@80 { + compatible = "snps,axs10x-arc-pll-clock"; + reg = <0x80 0x10>, <0x100 0x10>; + #clock-cells = <0>; + clocks = <&input_clk>; + + /* + * Set initial core pll output frequency to 100MHz. + * It will be applied at the core pll driver probing + * on early boot. + */ + assigned-clocks = <&core_clk>; + assigned-clock-rates = <100000000>; + }; + + core_intc: archs-intc@cpu { + compatible = "snps,archs-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + + idu_intc: idu-interrupt-controller { + compatible = "snps,archs-idu-intc"; + interrupt-controller; + interrupt-parent = <&core_intc>; + #interrupt-cells = <1>; + }; + + /* + * this GPIO block ORs all interrupts on CPU card (creg,..) + * to uplink only 1 IRQ to ARC core intc + */ + dw-apb-gpio@2000 { + compatible = "snps,dw-apb-gpio"; + reg = < 0x2000 0x80 >; + #address-cells = <1>; + #size-cells = <0>; + + ictl_intc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <30>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&idu_intc>; + interrupts = <1>; + }; + }; + + debug_uart: dw-apb-uart@5000 { + compatible = "snps,dw-apb-uart"; + reg = <0x5000 0x100>; + clock-frequency = <33333000>; + interrupt-parent = <&ictl_intc>; + interrupts = <2 4>; + baud = <115200>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + arcpct0: pct { + compatible = "snps,archs-pct"; + #interrupt-cells = <1>; + interrupt-parent = <&core_intc>; + interrupts = <20>; + }; + }; + + /* + * Mark DMA peripherals connected via IOC port as dma-coherent. We do + * it via overlay because peripherals defined in axs10x_mb.dtsi are + * used for both AXS101 and AXS103 boards and only AXS103 has IOC (so + * only AXS103 board has HW-coherent DMA peripherals) + * We don't need to mark pgu@17000 as dma-coherent because it uses + * external DMA buffer located outside of IOC aperture. + */ + axs10x_mb { + ethernet@18000 { + dma-coherent; + }; + + usb@40000 { + dma-coherent; + }; + + usb@60000 { + dma-coherent; + }; + + mmc@15000 { + dma-coherent; + }; + }; + + /* + * This INTC is actually connected to DW APB GPIO + * which acts as a wire between MB INTC and CPU INTC. + * GPIO INTC is configured in platform init code + * and here we mimic direct connection from MB INTC to + * CPU INTC, thus we set "interrupts = <0 1>" instead of + * "interrupts = <12>" + * + * This intc actually resides on MB, but we move it here to + * avoid duplicating the MB dtsi file given that IRQ from + * this intc to cpu intc are different for axs101 and axs103 + */ + mb_intc: interrupt-controller@e0012000 { + #interrupt-cells = <1>; + compatible = "snps,dw-apb-ictl"; + reg = < 0x0 0xe0012000 0x0 0x200 >; + interrupt-controller; + interrupt-parent = <&idu_intc>; + interrupts = <0>; + }; + + memory { + device_type = "memory"; + /* CONFIG_LINUX_RAM_BASE needs to match low mem start */ + reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MiB low mem */ + 0x1 0xc0000000 0x0 0x40000000>; /* 1 GiB highmem */ + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + /* + * Move frame buffer out of IOC aperture (0x8z-0xaz). + */ + frame_buffer: frame_buffer@be000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xbe000000 0x0 0x2000000>; + no-map; + }; + }; +}; |