diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts')
-rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts | 103 |
1 files changed, 103 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts index 41cadb906b..3b7fdb6797 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts @@ -3,9 +3,12 @@ /dts-v1/; #include "msm8916-pm8916.dtsi" +#include "msm8916-modem-qdsp6.dtsi" + #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / { model = "BQ Aquaris X5 (Longcheer L8910)"; @@ -22,6 +25,16 @@ stdout-path = "serial0"; }; + speaker_amp: audio-amplifier { + compatible = "awinic,aw8738"; + mode-gpios = <&tlmm 114 GPIO_ACTIVE_HIGH>; + awinic,mode = <5>; + sound-name-prefix = "Speaker Amp"; + + pinctrl-0 = <&spk_ext_pa_default>; + pinctrl-names = "default"; + }; + flash-led-controller { compatible = "ocs,ocp8110"; enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; @@ -74,6 +87,46 @@ }; }; +&blsp_i2c2 { + status = "okay"; + + led-controller@30 { + compatible = "kinetic,ktd2026"; + reg = <0x30>; + #address-cells = <1>; + #size-cells = <0>; + + vin-supply = <&pm8916_l17>; + vio-supply = <&pm8916_l6>; + + pinctrl-0 = <&status_led_default>; + pinctrl-names = "default"; + + multi-led { + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_STATUS; + + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_RED>; + }; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_BLUE>; + }; + }; + }; +}; + &blsp_i2c3 { status = "okay"; @@ -107,6 +160,27 @@ status = "okay"; }; +&mpss_mem { + reg = <0x0 0x86800000 0x0 0x5000000>; +}; + +&pm8916_codec { + qcom,micbias-lvl = <2800>; + qcom,mbhc-vthreshold-low = <75 100 120 180 500>; + qcom,mbhc-vthreshold-high = <75 100 120 180 500>; + qcom,hphl-jack-type-normally-open; +}; + +&pm8916_gpios { + status_led_default: status-led-default-state { + pins = "gpio3"; + function = PMIC_GPIO_FUNC_NORMAL; + power-source = <PM8916_GPIO_VPH>; + bias-disable; + output-high; + }; +}; + &pm8916_resin { status = "okay"; linux,code = <KEY_VOLUMEDOWN>; @@ -137,6 +211,28 @@ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; }; +&sound { + /* + * Provide widgets/pin-switches to allow enabling speaker separately. + * The hardware does not provide a way to disable the output via the + * headphone jack when the speaker is enabled. + */ + model = "bq-paella"; + widgets = + "Speaker", "Speaker", + "Headphone", "Headphones"; + pin-switches = "Speaker"; + audio-routing = + "Speaker", "Speaker Amp OUT", + "Speaker Amp IN", "HPH_R", + "Headphones", "HPH_L", + "Headphones", "HPH_R", + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + aux-devs = <&speaker_amp>; +}; + &usb { status = "okay"; extcon = <&usb_id>, <&usb_id>; @@ -205,6 +301,13 @@ bias-disable; }; + spk_ext_pa_default: spk-ext-pa-default-state { + pins = "gpio114"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + usb_id_default: usb-id-default-state { pins = "gpio110"; function = "gpio"; |