diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi | 92 |
1 files changed, 73 insertions, 19 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi index c19cf20d74..fbd2caf405 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi @@ -3,9 +3,12 @@ /dts-v1/; #include "msm8916-pm8916.dtsi" +#include "msm8916-modem-qdsp6.dtsi" + #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/sound/apq8016-lpass.h> / { aliases { @@ -65,25 +68,6 @@ }; }; -&blsp_i2c4 { - status = "okay"; - - fuelgauge@36 { - compatible = "maxim,max77849-battery"; - reg = <0x36>; - - maxim,rsns-microohm = <10000>; - maxim,over-heat-temp = <600>; - maxim,over-volt = <4400>; - - interrupt-parent = <&tlmm>; - interrupts = <121 IRQ_TYPE_EDGE_FALLING>; - - pinctrl-0 = <&fuelgauge_int_default>; - pinctrl-names = "default"; - }; -}; - &blsp_i2c2 { status = "okay"; @@ -112,10 +96,52 @@ }; }; +&blsp_i2c4 { + status = "okay"; + + fuelgauge@36 { + compatible = "maxim,max77849-battery"; + reg = <0x36>; + + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4400>; + + interrupt-parent = <&tlmm>; + interrupts = <121 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-0 = <&fuelgauge_int_default>; + pinctrl-names = "default"; + }; +}; + &blsp_uart2 { status = "okay"; }; +/* + * For some reason the speaker amplifier is connected to the second SD line + * (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the + * device tree, otherwise audio will seemingly play fine on the wrong SD line + * but the speaker stays silent. + * + * When routing audio via QDSP6 (the default) the &lpass node is reserved and + * the definitions from &q6afedai are used. When the modem is disabled audio can + * be alternatively routed directly to the LPASS hardware with reduced latency. + * The definitions for &lpass are here for completeness to simplify changing the + * setup with minor changes to the DT (either manually or with DT overlays). + */ +&lpass { + dai-link@3 { + reg = <MI2S_QUATERNARY>; + qcom,playback-sd-lines = <1>; + }; +}; + +&mpss_mem { + reg = <0x0 0x86800000 0x0 0x5400000>; +}; + &pm8916_resin { linux,code = <KEY_VOLUMEDOWN>; status = "okay"; @@ -133,6 +159,13 @@ status = "okay"; }; +&q6afedai { + dai@22 { + reg = <QUATERNARY_MI2S_RX>; + qcom,sd-lines = <1>; + }; +}; + &sdhc_1 { status = "okay"; }; @@ -147,6 +180,27 @@ status = "okay"; }; +&sound { + audio-routing = + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + + sound_link_backend2: backend2-dai-link { + link-name = "Quaternary MI2S"; + + cpu { + sound-dai = <&q6afedai QUATERNARY_MI2S_RX>; + }; + platform { + sound-dai = <&q6routing>; + }; + codec { + sound-dai = <&speaker_codec>; + }; + }; +}; + &usb { dr_mode = "peripheral"; extcon = <&pm8916_usbin>; |