diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/qrb4210-rb2.dts')
-rw-r--r-- | arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 115 |
1 files changed, 106 insertions, 9 deletions
diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts index 9738c0dacd..52f31f3166 100644 --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts @@ -15,6 +15,7 @@ aliases { serial0 = &uart4; + serial1 = &uart3; }; chosen { @@ -280,6 +281,12 @@ status = "okay"; }; +&remoteproc_mpss { + firmware-name = "qcom/qrb4210/modem.mbn"; + + status = "okay"; +}; + &rpm_requests { regulators { compatible = "qcom,rpm-pm6125-regulators"; @@ -346,13 +353,14 @@ }; vreg_l8a_0p664: l8 { - regulator-min-microvolt = <400000>; - regulator-max-microvolt = <728000>; + regulator-min-microvolt = <640000>; + regulator-max-microvolt = <640000>; }; vreg_l9a_1p8: l9 { regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2000000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; }; vreg_l10a_1p8: l10 { @@ -389,11 +397,13 @@ vreg_l16a_1p3: l16 { regulator-min-microvolt = <1704000>; regulator-max-microvolt = <1904000>; + regulator-allow-set-load; }; vreg_l17a_1p3: l17 { regulator-min-microvolt = <1152000>; regulator-max-microvolt = <1384000>; + regulator-allow-set-load; }; vreg_l18a_1p232: l18 { @@ -424,8 +434,9 @@ }; vreg_l23a_3p3: l23 { - regulator-min-microvolt = <3200000>; - regulator-max-microvolt = <3400000>; + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; + regulator-allow-set-load; }; vreg_l24a_2p96: l24 { @@ -487,6 +498,66 @@ <56 3>, <61 2>, <64 1>, <68 1>, <72 8>, <96 1>; + uart3_default: uart3-default-state { + cts-pins { + pins = "gpio8"; + function = "qup3"; + drive-strength = <2>; + bias-bus-hold; + }; + + rts-pins { + pins = "gpio9"; + function = "qup3"; + drive-strength = <2>; + bias-disable; + }; + + tx-pins { + pins = "gpio10"; + function = "qup3"; + drive-strength = <2>; + bias-disable; + }; + + rx-pins { + pins = "gpio11"; + function = "qup3"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + uart3_sleep: uart3-sleep-state { + cts-pins { + pins = "gpio8"; + function = "gpio"; + drive-strength = <2>; + bias-bus-hold; + }; + + rts-pins { + pins = "gpio9"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + tx-pins { + pins = "gpio10"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + rx-pins { + pins = "gpio11"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + lt9611_rst_pin: lt9611-rst-state { pins = "gpio41"; function = "gpio"; @@ -508,16 +579,32 @@ }; }; -&uart4 { +&uart3 { + interrupts-extended = <&intc GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 11 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-0 = <&uart3_default>; + pinctrl-1 = <&uart3_sleep>; + pinctrl-names = "default", "sleep"; status = "okay"; + + bluetooth { + compatible = "qcom,wcn3988-bt"; + + vddio-supply = <&vreg_l9a_1p8>; + vddxo-supply = <&vreg_l16a_1p3>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l23a_3p3>; + enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>; + max-speed = <3200000>; + }; }; -&usb { +&uart4 { status = "okay"; }; -&usb_dwc3 { - maximum-speed = "super-speed"; +&usb { + status = "okay"; }; &usb_hsphy { @@ -535,6 +622,16 @@ status = "okay"; }; +&wifi { + vdd-0.8-cx-mx-supply = <&vreg_l8a_0p664>; + vdd-1.8-xo-supply = <&vreg_l16a_1p3>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l23a_3p3>; + qcom,ath10k-calibration-variant = "Thundercomm_RB2"; + + status = "okay"; +}; + &xo_board { clock-frequency = <19200000>; }; |