diff options
Diffstat (limited to 'arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi | 214 |
1 files changed, 207 insertions, 7 deletions
diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi index a199de8f8b..d33ab4c887 100644 --- a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi +++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi @@ -9,18 +9,36 @@ #include <dt-bindings/pinctrl/rzg2l-pinctrl.h> /* - * Signals of SW_CONFIG switches: - * @SW_SD0_DEV_SEL: - * 0 - SD0 is connected to eMMC - * 1 - SD0 is connected to uSD0 card + * On-board switches' states: + * @SW_OFF: switch's state is OFF + * @SW_ON: switch's state is ON */ -#define SW_SD0_DEV_SEL 1 +#define SW_OFF 0 +#define SW_ON 1 + +/* + * SW_CONFIG[x] switches' states: + * @SW_CONFIG2: + * SW_OFF - SD0 is connected to eMMC + * SW_ON - SD0 is connected to uSD0 card + * @SW_CONFIG3: + * SW_OFF - SD2 is connected to SoC + * SW_ON - SCIF1, SSI0, IRQ0, IRQ1 connected to SoC + */ +#define SW_CONFIG2 SW_ON +#define SW_CONFIG3 SW_ON / { compatible = "renesas,rzg3s-smarcm", "renesas,r9a08g045s33", "renesas,r9a08g045"; aliases { mmc0 = &sdhi0; +#if SW_CONFIG3 == SW_OFF + mmc2 = &sdhi2; +#else + eth0 = ð0; + eth1 = ð1; +#endif }; chosen { @@ -43,7 +61,7 @@ enable-active-high; }; -#if SW_SD0_DEV_SEL +#if SW_CONFIG2 == SW_ON vccq_sdhi0: regulator1 { compatible = "regulator-gpio"; regulator-name = "SDHI0 VccQ"; @@ -63,13 +81,76 @@ regulator-always-on; }; #endif + + vcc_sdhi2: regulator2 { + compatible = "regulator-fixed"; + regulator-name = "SDHI2 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpios = <&pinctrl RZG2L_GPIO(8, 1) GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +#if SW_CONFIG3 == SW_ON +ð0 { + pinctrl-0 = <ð0_pins>; + pinctrl-names = "default"; + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; + status = "okay"; + + phy0: ethernet-phy@7 { + reg = <7>; + interrupt-parent = <&pinctrl>; + interrupts = <RZG2L_GPIO(12, 0) IRQ_TYPE_EDGE_FALLING>; + rxc-skew-psec = <0>; + txc-skew-psec = <0>; + rxdv-skew-psec = <0>; + txen-skew-psec = <0>; + rxd0-skew-psec = <0>; + rxd1-skew-psec = <0>; + rxd2-skew-psec = <0>; + rxd3-skew-psec = <0>; + txd0-skew-psec = <0>; + txd1-skew-psec = <0>; + txd2-skew-psec = <0>; + txd3-skew-psec = <0>; + }; }; +ð1 { + pinctrl-0 = <ð1_pins>; + pinctrl-names = "default"; + phy-handle = <&phy1>; + phy-mode = "rgmii-id"; + status = "okay"; + + phy1: ethernet-phy@7 { + reg = <7>; + interrupt-parent = <&pinctrl>; + interrupts = <RZG2L_GPIO(12, 1) IRQ_TYPE_EDGE_FALLING>; + rxc-skew-psec = <0>; + txc-skew-psec = <0>; + rxdv-skew-psec = <0>; + txen-skew-psec = <0>; + rxd0-skew-psec = <0>; + rxd1-skew-psec = <0>; + rxd2-skew-psec = <0>; + rxd3-skew-psec = <0>; + txd0-skew-psec = <0>; + txd1-skew-psec = <0>; + txd2-skew-psec = <0>; + txd3-skew-psec = <0>; + }; +}; +#endif + &extal_clk { clock-frequency = <24000000>; }; -#if SW_SD0_DEV_SEL +#if SW_CONFIG2 == SW_ON /* SD0 slot */ &sdhi0 { pinctrl-0 = <&sdhi0_pins>; @@ -100,7 +181,104 @@ }; #endif +#if SW_CONFIG3 == SW_OFF +&sdhi2 { + pinctrl-0 = <&sdhi2_pins>; + pinctrl-names = "default"; + vmmc-supply = <&vcc_sdhi2>; + bus-width = <4>; + max-frequency = <50000000>; + status = "okay"; +}; +#endif + &pinctrl { +#if SW_CONFIG3 == SW_ON + eth0-phy-irq-hog { + gpio-hog; + gpios = <RZG2L_GPIO(12, 0) GPIO_ACTIVE_LOW>; + input; + line-name = "eth0-phy-irq"; + }; +#endif + + eth0_pins: eth0 { + txc { + pinmux = <RZG2L_PORT_PINMUX(1, 0, 1)>; /* ET0_TXC */ + power-source = <1800>; + output-enable; + input-enable; + drive-strength-microamp = <5200>; + }; + + tx_ctl { + pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>; /* ET0_TX_CTL */ + power-source = <1800>; + output-enable; + drive-strength-microamp = <5200>; + }; + + mux { + pinmux = <RZG2L_PORT_PINMUX(1, 2, 1)>, /* ET0_TXD0 */ + <RZG2L_PORT_PINMUX(1, 3, 1)>, /* ET0_TXD1 */ + <RZG2L_PORT_PINMUX(1, 4, 1)>, /* ET0_TXD2 */ + <RZG2L_PORT_PINMUX(2, 0, 1)>, /* ET0_TXD3 */ + <RZG2L_PORT_PINMUX(3, 0, 1)>, /* ET0_RXC */ + <RZG2L_PORT_PINMUX(3, 1, 1)>, /* ET0_RX_CTL */ + <RZG2L_PORT_PINMUX(3, 2, 1)>, /* ET0_RXD0 */ + <RZG2L_PORT_PINMUX(3, 3, 1)>, /* ET0_RXD1 */ + <RZG2L_PORT_PINMUX(4, 0, 1)>, /* ET0_RXD2 */ + <RZG2L_PORT_PINMUX(4, 1, 1)>, /* ET0_RXD3 */ + <RZG2L_PORT_PINMUX(4, 3, 1)>, /* ET0_MDC */ + <RZG2L_PORT_PINMUX(4, 4, 1)>, /* ET0_MDIO */ + <RZG2L_PORT_PINMUX(4, 5, 1)>; /* ET0_LINKSTA */ + power-source = <1800>; + }; + }; + +#if SW_CONFIG3 == SW_ON + eth1-phy-irq-hog { + gpio-hog; + gpios = <RZG2L_GPIO(12, 1) GPIO_ACTIVE_LOW>; + input; + line-name = "eth1-phy-irq"; + }; +#endif + + eth1_pins: eth1 { + txc { + pinmux = <RZG2L_PORT_PINMUX(7, 0, 1)>; /* ET1_TXC */ + power-source = <1800>; + output-enable; + input-enable; + drive-strength-microamp = <5200>; + }; + + tx_ctl { + pinmux = <RZG2L_PORT_PINMUX(7, 1, 1)>; /* ET1_TX_CTL */ + power-source = <1800>; + output-enable; + drive-strength-microamp = <5200>; + }; + + mux { + pinmux = <RZG2L_PORT_PINMUX(7, 2, 1)>, /* ET1_TXD0 */ + <RZG2L_PORT_PINMUX(7, 3, 1)>, /* ET1_TXD1 */ + <RZG2L_PORT_PINMUX(7, 4, 1)>, /* ET1_TXD2 */ + <RZG2L_PORT_PINMUX(8, 0, 1)>, /* ET1_TXD3 */ + <RZG2L_PORT_PINMUX(8, 4, 1)>, /* ET1_RXC */ + <RZG2L_PORT_PINMUX(9, 0, 1)>, /* ET1_RX_CTL */ + <RZG2L_PORT_PINMUX(9, 1, 1)>, /* ET1_RXD0 */ + <RZG2L_PORT_PINMUX(9, 2, 1)>, /* ET1_RXD1 */ + <RZG2L_PORT_PINMUX(9, 3, 1)>, /* ET1_RXD2 */ + <RZG2L_PORT_PINMUX(10, 0, 1)>, /* ET1_RXD3 */ + <RZG2L_PORT_PINMUX(10, 2, 1)>, /* ET1_MDC */ + <RZG2L_PORT_PINMUX(10, 3, 1)>, /* ET1_MDIO */ + <RZG2L_PORT_PINMUX(10, 4, 1)>; /* ET1_LINKSTA */ + power-source = <1800>; + }; + }; + sdhi0_pins: sd0 { data { pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3"; @@ -139,4 +317,26 @@ "SD0_CLK", "SD0_CMD", "SD0_RST#"; power-source = <1800>; }; + + sdhi2_pins: sd2 { + data { + pins = "P11_2", "P11_3", "P12_0", "P12_1"; + input-enable; + }; + + ctrl { + pins = "P11_1"; + input-enable; + }; + + mux { + pinmux = <RZG2L_PORT_PINMUX(11, 0, 8)>, /* SD2_CLK */ + <RZG2L_PORT_PINMUX(11, 1, 8)>, /* SD2_CMD */ + <RZG2L_PORT_PINMUX(11, 2, 8)>, /* SD2_DATA0 */ + <RZG2L_PORT_PINMUX(11, 3, 8)>, /* SD2_DATA1 */ + <RZG2L_PORT_PINMUX(12, 0, 8)>, /* SD2_DATA2 */ + <RZG2L_PORT_PINMUX(12, 1, 8)>, /* SD2_DATA3 */ + <RZG2L_PORT_PINMUX(14, 1, 7)>; /* SD2_CD# */ + }; + }; }; |